Cisco 7600 Series Router Software Configuration Guide Cisco IOS Release 15S
Product Overview
Download this chapter
Product OverviewProduct Overview
Download the complete book
Full Book PDF of Cisco 7600 Series Router Cisco IOS Software Configuration GuideFull Book PDF of Cisco 7600 Series Router Cisco IOS Software Configuration Guide (PDF - 9 MB)
 Feedback

Table Of Contents

Product Overview

Supported Hardware and Software

User Interfaces

Configuring Embedded CiscoView Support

Understanding Embedded CiscoView

Installing and Configuring Embedded CiscoView

Displaying Embedded CiscoView Information

Software Features Supported in Hardware by the PFC and DFC

Software Features Supported in Hardware by the PFC3, DFC3, and DFC

Software Features Supported in Hardware by the PFC3 and DFC3


Product Overview

This chapter contains these sections:

•Supported Hardware and Software

•User Interfaces

•Configuring Embedded CiscoView Support

•Software Features Supported in Hardware by the PFC and DFC

Supported Hardware and Software

For complete information about the chassis, modules, and software features supported by Cisco 7600 series routers, refer to the Release Notes for Cisco IOS Release 12.2SX on the Supervisor Engine 720, Supervisor Engine 32, and Supervisor Engine 2.

See "Cisco IOS Release 15.S Software Images," for information about the Cisco IOS software images available for this release.

Note In Cisco IOS Release 12.2SR and later releases, the Supervisor Engine 2, policy feature card 2 (PFC2), and FlexWAN module are no longer supported on Cisco 7600 series routers.

User Interfaces

Release 12.2SR supports configuration using the following interfaces:

•CLI—Refer to "Using the Command-Line Interface" in the Release 12.2 Cisco IOS Configuration Fundamentals Configuration Guide at this URL:

http://www.cisco.com/en/US/docs/ios/fundamentals/configuration/guide/12_2sr/cf_12_2sr_book.html

•SNMP—Refer to the Release 12.2 Cisco IOS Configuration Fundamentals Configuration Guide and Command Reference documents at this URL:

http://www.cisco.com/en/US/docs/ios/fundamentals/configuration/guide/12_2sr/cf_12_2sr_book.html

•Cisco IOS web browser interface—Refer to "Using the Cisco Web Browser" in the Cisco IOS Configuration Fundamentals Configuration Guide at this URL:

http://www.cisco.com/en/US/docs/ios/fundamentals/configuration/guide/12_2sr/cf_12_2sr_book.html

•Embedded CiscoView—See the "Configuring Embedded CiscoView Support" section.

Configuring Embedded CiscoView Support

These sections describe configuring Embedded CiscoView support:

•Understanding Embedded CiscoView

•Installing and Configuring Embedded CiscoView

•Displaying Embedded CiscoView Information

Understanding Embedded CiscoView

The Embedded CiscoView network management system is a web-based interface that uses HTTP and SNMP to provide a graphical representation of the router and to provide a GUI-based management and configuration interface. You can download the Java Archive (JAR) files for Embedded CiscoView at:

http://www.cisco.com/cisco/software/navigator.html

Installing and Configuring Embedded CiscoView

To install and configure Embedded CiscoView, perform this task:

 
Command
Purpose

Step 1 

Router# dir device_name

Displays the contents of the device.

If you are installing Embedded CiscoView for the first time, or if the CiscoView directory is empty, skip to Step 4.

Step 2 

Router# delete device_name:cv/*

Removes existing files from the CiscoView directory.

Step 3 

Router# squeeze device_name:

Recovers the space in the file system.

Step 4 

Router# archive tar /xtract tftp:// ip_address_of_tftp_server/ciscoview.tar device_name:cv

Extracts the CiscoView files from the tar file on the TFTP server to the CiscoView directory.

Step 5 

Router# dir device_name:

Displays the contents of the device.

In a redundant configuration, repeat Step 1 through Step 5 for the file system on the redundant supervisor engine.

Step 6 

Router# configure terminal

Enters global configuration mode.

Step 7 

Router(config)# ip http server

Enables the HTTP web server.

Step 8 

Router(config)# snmp-server community string ro

Configures the SNMP password for read-only operation.

Step 9 

Router(config)# snmp-server community string rw

Configures the SNMP password for read/write operation.

Note The default password for accessing the router web page is the enable-level password of the router.

For more information about web access to the router, refer to "Using the Cisco Web Browser" in the Cisco IOS Configuration Fundamentals Configuration Guide at this URL:

/en/US/docs/ios/12_2/configfun/configuration/guide/fcf005.html

Displaying Embedded CiscoView Information

To display the Embedded CiscoView information, enter the following EXEC commands:

Command
Purpose

Router# show ciscoview package

Displays information about the Embedded CiscoView files.

Router# show ciscoview version

Displays the Embedded CiscoView version.


Software Features Supported in Hardware by the PFC and DFC

These sections describe the hardware support provided by Policy Feature Card 3 (PFC3), Distributed Forwarding Card 3 (DFC3), and Distributed Forwarding Card (DFC):

•Software Features Supported in Hardware by the PFC3, DFC3, and DFC

•Software Features Supported in Hardware by the PFC3 and DFC3

Software Features Supported in Hardware by the PFC3, DFC3, and DFC

The PFC3, DFC3, and DFC provide hardware support for these Cisco IOS software features:

•Access Control Lists (ACLs) for Layer 3 ports and VLAN interfaces

–Permit and deny actions of input and output standard and extended ACLs

Note Flows that require ACL logging are processed in software on the MSFC.

–Except on MPLS interfaces, reflexive ACL flows after the first packet in a session is processed in software on the MSFC

–Dynamic ACL flows

Note Idle timeout is processed in software on the MSFC.

For more information about PFC and DFC support for ACLs, see Chapter 36 "Understanding Cisco IOS ACL Support." For complete information about configuring ACLs, refer to the Cisco IOS Security Configuration Guide, Release 12.2, "Traffic Filtering and Firewalls," at this URL:

http://www.cisco.com/en/US/docs/ios/12_2/security/configuration/guide/fsecur_c.html

•VLAN ACLs (VACLs)—To configure VACLs, see Chapter 38 "Configuring VLAN ACLs."

•Policy-based routing (PBR) for route-map sequences that use the match ip address, set ip next-hop, and ip default next-hop PBR keywords.

To configure PBR, refer to the Cisco IOS Quality of Service Solutions Configuration Guide, Release 12.2, "Classification" and "Configuring Policy-Based Routing," at this URL:

http://www.cisco.com/en/US/docs/ios/12_2/qos/configuration/guide/qcfpbr_ps1835_TSD_Products_Configuration_Guide_Chapter.html

Note If the MSFC3 or MSFC4 address falls within the range of a PBR ACL, traffic addressed to the MSFC is policy routed in hardware instead of being forwarded to the MSFC. To prevent policy routing of traffic addressed to a MSFC3 or MSFC4, configure PBR ACLs to deny traffic addressed to the MSFC.

•Except on MPLS interfaces, TCP intercept—To configure TCP intercept, see the "Configuring TCP Intercept" section.

•Hardware-assisted NetFlow Aggregation—Refer to this URL:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/configuration/guide/nde.html

Software Features Supported in Hardware by the PFC3 and DFC3

The PFC3 and DFC3 provide hardware support for these Cisco IOS software features:

•IPv4 Multicast over Point-to-Point generic route encapsulation (GRE) Tunnels—Refer to the publication at this URL:

http://www.cisco.com/en/US/docs/ios/12_2/interface/configuration/guide/icflogin.html

•Bidirectional Protocol Independent Multicast (PIM) in hardware—See the "Understanding How IPv4 Bidirectional PIM Works" section.

•Multiple-path Unicast Reverse Path Forwarding (RPF) Check—To configure Unicast RPF Check, see the "Configuring Unicast Reverse Path Forwarding Check" section.

•Except on MPLS interfaces, Network Address Translation (NAT) for IPv4 unicast and multicast traffic.

Note the following information about hardware-assisted NAT:

–NAT of UDP traffic is not supported in PFC3A mode.

–The PFC3 does not support NAT of multicast traffic.

–The PFC3 does not support NAT configured with a route-map that specifies length.

–When you configure NAT and NDE on an interface, the PFC3 sends all traffic in fragmented packets to the MSFC3 or MSFC4 to be processed in software. (CSCdz51590)

To configure NAT, see the Cisco IOS IP Configuration Guide, Release 12.2, "IP Addressing and Services," "Configuring IP Addressing," and "Configuring Network Address Translation," at this URL:

http://www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/fipr_c.html

To prevent a significant volume of NAT traffic from being sent to the MSFC3, due to either a DoS attack or a misconfiguration, enter the mls rate-limit unicast acl {ingress | egress} command described at this URL:

http://www.cisco.com/en/US/products/hw/switches/ps700/prod_command_reference_list.html

•The PFC3 and DFC3 support IPv4 multicast over point-to-point GRE tunnels in hardware.

•GRE Tunneling and IP in IP Tunneling—The PFC3 and DFC3 support the following tunnel commands:

–tunnel destination

–tunnel mode gre

–tunnel mode ipip

–tunnel source

–tunnel ttl

–tunnel tos

The MSFC3 and MSFC4 support tunneling configured with any other tunnel commands.

The tunnel ttl command (default 255) sets the TTL of encapsulated packets.

The tunnel tos command sets the ToS byte of a packet when it is encapsulated. If the tunnel tos command is not present and QoS is not enabled, the ToS byte of a packet sets the ToS byte of the packet when it is encapsulated. If the tunnel tos command is not present and QoS is enabled, the ToS byte of a packet as modified by PFC QoS sets the ToS byte of the packet when it is encapsulated.

To configure GRE Tunneling and IP in IP Tunneling, refer to these publications:

http://www.cisco.com/en/US/docs/ios/12_2/interface/configuration/guide/icflogin.html

http://www.cisco.com/en/US/docs/ios/12_2/interface/command/reference/irfshoip.html

To configure the tunnel tos and tunnel ttl commands, refer to this publication:

http://www.cisco.com/en/US/docs/ios/12_0s/feature/guide/12s_tos.html

Note the following information about tunnels:

–Each hardware-assisted tunnel must have a unique source. Hardware-assisted tunnels cannot share a source even if the destinations are different. Use secondary addresses on loopback interfaces or create multiple loopback interfaces. Failure to use unique source addresses may result in control plane failures during software path congestion.

–Each tunnel interface uses one internal VLAN.

–Each tunnel interface uses one additional router MAC address entry per router MAC address.

–The PFC3A does not support any PFC QoS features on tunnel interfaces. All other PFCs do.

–The MSFC3 and MSFC4 support tunnels configured with egress features on the tunnel interface. Examples of egress features are output Cisco IOS ACLs, NAT (for inside to outside translation), TCP intercept, CBAC, and encryption.