Table Of Contents

E

email domain (network location id)

enable (IMAP)

enable (network location)

enable (VoiceView Express)

enabled (ccn application)

enabled (ccn reporting historical)

enabled (ccn subsystem edbs dbprofile)-IVR Only

enabled (ccn trigger http)-IVR Only

enabled (ccn trigger jtapi)

enabled (ccn trigger sip)

erase startup-config

exec-commands (aaa accounting event)

E

---

Last Updated: August 03, 2009

email domain (network location id)

enable (IMAP)

enable (network location)

enable (VoiceView Express)

enabled (ccn application)

enabled (ccn reporting historical)

enabled (ccn subsystem edbs dbprofile)-IVR Only

enabled (ccn trigger http)-IVR Only

enabled (ccn trigger jtapi)

enabled (ccn trigger sip)

erase startup-config

exec-commands (aaa accounting event)

email domain (network location id)

To configure the e-mail domain for a voice-mail location, use the email command in Cisco Unity Express location configuration mode. To remove the e-mail domain for a location, use the no form of this command.

email domain {name | ip-address}

no email domain {name | ip-address}

Syntax Description

name	Configures the e-mail domain hostname for the location.
ip-address	Configures the e-mail domain IP address for the location.

Defaults

No e-mail domain is configured.

Command Modes

Location configuration

Command History

Cisco Unity Express Version	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.

Usage Guidelines

This command configures the e-mail domain name or IP address for the location. The domain name is added when a VPIM message is sent to the remote location (for example, "4843000@mycompany.com"). If you do not configure a domain name or IP address, the Cisco Unity Express system at this location cannot receive network messages.

Using the no form of this command removes the e-mail domain from the specified location.

---

Caution If you remove the e-mail domain for a remote network location, the system automatically disables networking from the Cisco Unity Express module to that location.
If you remove the e-mail domain for the local location, then networking on that Cisco Unity Express module is disabled.
To reenable a location, assign it a valid e-mail domain.

---

Examples

The following example configures the e-mail domain for network location 9 to 10.12.0.1.

se-10-0-0-0# config t

se-10-0-0-0(config)# network location id 9

se-10-0-0-0(config-location)# email domain 10.12.0.1

se-10-0-0-0(config-location)# end

se-10-0-0-0(config)#

Related Commands

Command	Description
ccn application	Configures the CCN applications, such as voice mail and auto attendant.
show call-agent	Displays the CCN application details.

enable (IMAP)

To enable the integrated messaging (IMAP) feature system wide, use the enable command in Cisco Unity Express IMAP mode. To disable the IMAP feature, use the no or default form of this command.

enable

no enable

default enable

Syntax Description

This command has no arguments or keywords.

Defaults

IMAP is disabled.

Command Modes

Cisco Unity Express IMAP

Command History

Cisco Unity Express Version	Modification
2.3	This command was introduced.

Usage Guidelines

This command is not available on the AIM.

Examples

The following example enables the IMAP feature:

se-10-0-0-0# config t

se-10-0-0-0(config)# service imap

se-10-0-0-0(config-imap)# enable

Related Commands

Command	Description
groupname	Assigns the IMAP feature to a group.
session idletimeout (IMAP)	Specifies the number of seconds before the session terminates.
service imap	Enters the IMAP configuration mode.
session security	Specifies the type of security connection.
show imap configuration	Displays configured IMAP parameters.
show imap sessions	Displays active IMAP sessions.

enable (network location)

To enable a network location to send and receive Cisco Unity Express voice mail messages, use the enable command in Cisco Unity Express location configuration mode. To disable the location, use the no form of this command.

enable

no enable

Syntax Description

This command has no arguments or keywords.

Defaults

Network locations are enabled.

Command Modes

Cisco Unity Express location configuration

Command History

Cisco Unity Express Version	Modification
2.1	This command was introduced.

Usage Guidelines

Network locations are enabled by default to send and receive Cisco Unity Express voice mail messages. Use the no enable command to prevent communication to the location. Use the enable command to reestablish communication to the network location.

---

Note The no enable command does not erase the network location from the Cisco Unity Express database.

---

Examples

The following example displays the details for network location 15 with networking disabled:

se-10-0-0-0# config t

se-10-0-0-0(config)# network location id 15

se-10-0-0-0(config-location)# no enable

!!!WARNING!!!:Disabling location will disable 

networking to/from this location.

Do you wish to continue[n]?:y

se-10-0-0-0(config-location)# end

se-10-0-0-0(config)# exit

se-10-0-0-0# 

se-10-0-0-0# show network detail location id 15

Name:                      houston

Abbreviation:              hou

Email domain:              how.cue.abcdef.com

Minimum extension length:  2

Maximum extension length:  15

Phone prefix:              4

VPIM encoding:             dynamic

Send spoken name:          enabled

Send vCard:                enabled

State:                     disabled

VPIM broadcast ID:         vpim-broadcast

Sent msg count:            1

Received msg count:        1

The following example reestablishes voice-mail transmission to and from network location 15.

se-10-0-0-0# config t

se-10-0-0-0(config)# network location id 15

se-10-0-0-0(config-location)# enable

se-10-0-0-0(config-location)# end

se-10-0-0-0(config)# exit

Related Commands

Command	Description
network location	Specifies a network ID for a remote site.
show network detail local	Displays details of a specified network location.

enable (VoiceView Express)

To enable the VoiceView Express feature, use the enable command in Cisco Unity Express VoiceView mode. To disable the VoiceView Express feature, use the no or default form of this command.

enable

no enable

default enable

Syntax Description

This command has no arguments or keywords.

Defaults

VoiceView Express is enabled.

Command Modes

Cisco Unity Express VoiceView Express

Command History

Cisco Unity Express Version	Modification
2.3	This command was introduced.
3.0	This command was implemented on the advanced integration module (AIM).

Usage Guidelines

This command is not available on the AIM for version 2.3 and earlier.

Examples

The following example enables the VoiceView Express feature:

se-10-0-0-0# config t

se-10-0-0-0(config)# service voiceview

se-10-0-0-0(config-voiceview)# enable

Related Commands

Command	Description
session idletimeout (VoiceView Express)	Specifies the number of seconds before the session terminates.
service voiceview	Enters the VoiceView Express configuration mode.
show voiceview configuration	Displays configured VoiceView Express parameters.
show voiceview sessions	Displays active VoiceView Express sessions.

enabled (ccn application)

To start an application, use the enabled command in Cisco Unity Express CCN configuration application mode. To disable the application, use the no form of this command.

enabled

no enabled

Syntax Description

This command has no arguments or keywords.

Command Modes

CCN configuration application

Command History

Cisco Unity Express Version	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.

Examples

The following example enables the autoattendant application.

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn application autoattendant

se-10-0-0-0(config-application)# enabled

se-10-0-0-0(config-application)# end

se-10-0-0-0(config)#

Related Commands

Command	Description
ccn application	Configures the CCN applications, such as voice mail and auto attendant.
show call-agent	Displays the CCN application details.

enabled (ccn reporting historical)

To enable the Cisco Unity Express IVR reporting historical database, use the enabled command in the Cisco Unity Express IVR reporting historical configuration mode. Use the no form of this command to disable the historical reporting database.

enabled

no enabled

Syntax Description

This command has no arguments or keywords.

Command Default

The reporting historical database is enabled.

Command Modes

Cisco Unity Express IVR reporting historical configuration

Command History

Cisco Unity Express Version	Modification
3.0	This command was introduced.

Usage Guidelines

The reporting historical database is enabled by default. If the reporting historical database is disabled, call-related events are not stored in the database.

Examples

The following example disables the Cisco Unity Express IVR reporting historical database:

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn reporting historical

se-10-0-0-0(config-hrdm)# no enabled

se-10-0-0-0(config-hrdm)# end

se-10-0-0-0(config)# exit

Related Commands

Command	Description
show ccn reporting historical	Displays the Cisco Unity Express IVR reporting historical database configuration settings.

enabled (ccn subsystem edbs dbprofile)-IVR Only

To enable the Cisco Unity Express IVR enterprise database system (EDBS) profile for use in the database steps for running scripts, use the enabled command in Cisco Unity Express IVR EDBS profile configuration mode. Use the no form of this command to disable the database.

enabled

no enabled

Syntax Description

This command has no arguments or keywords.

Command Default

The EDBS profile is enabled.

Command Modes

Cisco Unity Express IVR EDBS profile configuration

Command History

Cisco Unity Express Version	Modification
3.0	This command was introduced.

Usage Guidelines

After configuring the database profile parameters, use the enabled command to enable the Cisco Unity Express IVR EDBS profile for use with scripts.

Examples

The following example disables the EDBS profile mydbprofile using the no form of the command:

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn subsystem edbs dbprofile mydbprofile

Adding new Database profile

se-10-0-0-0(config-dbprof)# no enabled

se-10-0-0-0(config-dbprof)# end

se-10-0-0-0(config)# exit

Related Commands

Command	Description
show ccn subsystem edbs dbprofile-IVR Only	Displays the Cisco Unity Express IVR EDBS configuration settings.

enabled (ccn trigger http)-IVR Only

To enable the Cisco Unity Express IVR HTTP-based URL and application trigger, use the enabled command in Cisco Unity Express IVR HTTP trigger configuration mode. Use the no form of this command to disable the trigger from processing the incoming HTTP request.

enabled

no enabled

Syntax Description

This command has no arguments or keywords.

Command Default

The HTTP-based trigger is enabled.

Command Modes

Cisco Unity Express IVR HTTP trigger configuration

Command History

Cisco Unity Express Version	Modification
3.0	This command was introduced.

Usage Guidelines

After configuring the HTTP trigger parameters, use the enabled command to start processing incoming HTTP requests.

Examples

The following example enables an HTTP-based trigger application:

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn trigger http urlname myhttpapp

Adding new trigger

se-10-0-0-0(config-trigger)# application myapplication

se-10-0-0-0(config-trigger)# enabled

se-10-0-0-0(config-trigger)# end

se-10-0-0-0(config)# exit

Related Commands

Command	Description
show ccn trigger http-IVR Only	Displays the trigger and application settings. Use the show ccn trigger http command option to display the configured Cisco Unity Express IVR HTTP-based trigger settings.

enabled (ccn trigger jtapi)

To start a trigger, use the enabled command in Cisco Unity Express CCN configuration trigger mode. To disable the trigger, use the no form of this command.

enabled

no enabled

Syntax Description

This command has no arguments or keywords.

Command Modes

CCN configuration trigger mode

Command History

Cisco Unity Express Version	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.

Examples

The following example enables the trigger 1234.

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn trigger jtapi phonenumber 1234

se-10-0-0-0(config-trigger)# enabled

se-10-0-0-0(config-trigger)# end

se-10-0-0-0(config)#

Related Commands

Command	Description
ccn trigger jtapi phonenumber	Enters trigger configuration mode.
show ccn trigger all	Displays the CCN trigger details.

enabled (ccn trigger sip)

To start a trigger, use the enabled command in Cisco Unity Express CCN configuration trigger mode. To disable the trigger, use the no form of this command.

enabled

no enabled

Syntax Description

This command has no arguments or keywords.

Command Modes

CCN configuration trigger mode

Command History

Cisco Unity Express Version	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.

Examples

The following example enables the trigger 1234.

se-10-0-0-0# config t

se-10-0-0-0(config)# ccn trigger sip phonenumber 1234

se-10-0-0-0(config-trigger)# enabled

se-10-0-0-0(config-trigger)# end

se-10-0-0-0(config)#

Related Commands

Command	Description
ccn trigger sip phonenumber	Enters trigger configuration mode.
show ccn trigger all	Displays the CCN trigger details.

erase startup-config

To erase the startup configuration, use the erase startup-config command in Cisco Unity Express EXEC mode.

erase startup-config

Syntax Description

This command has no arguments or keywords.

Command Modes

Cisco Unity Express EXEC

Command History

Cisco Unity Express Version	Modification
1.0	This command was introduced on the Cisco Unity Express network module and in Cisco Unified Communications Manager Express 3.0.
1.1	This command was implemented on the advanced integration module (AIM) and in Cisco Unified Communications Manager 3.3(3).
1.1.2	This command was implemented on the Cisco 2800 series and Cisco 3800 series routers.

Examples

The following example deletes the startup configuration from flash memory:

se-10-0-0-0# erase startup-config

Related Commands

Command	Description
write	Copies the running configuration to the startup configuration.

exec-commands (aaa accounting event)

To enable or disable the logging of EXEC mode commands, use the exec-commands command in Cisco Unity Express AAA accounting event configuration mode. Use the no form of this command to disable the logging of EXEC mode commands. Use the default form of this command to restore the default setting (the logging of EXEC mode commands is enabled).

exec-commands

no exec-commands

default exec-commands

Syntax Description

This command has no arguments or keywords.

Command Default

The logging of EXEC mode commands is enabled.

Command Modes

Cisco Unity Express AAA accounting event configuration (aaa-accounting-event)

Command History

Cisco Unity Express Version	Modification
7.0	This command was introduced.

Usage Guidelines

This command enables the logging of any Cisco Unity Express EXEC mode commands made using any interface except IMAP (CLI, GUI, TUI, and VVE).

Examples

The following example disables the logging of EXEC mode commands:

se-10-0-0-0# config t

se-10-0-0-0(config)# aaa accounting event

se-10-0-0-0(aaa-accounting-event)# no exec-commands

Related Commands

Command	Description
aaa accounting enable	Enables the recording of AAA accounting events.
aaa accounting event	Enters AAA accounting submode and configures event filtering for accounting packets.
show aaa accounting event	Shows the AAA accounting events that are designated to be logged.