Table Of Contents

L Commands

log-adjacency-changes (FabricPath)

lsp-gen-interval (FabricPath)

lsp-mtu (FabricPath)

L Commands

---

This chapter describes the Cisco NX-OS FabricPath commands that begin with L.

log-adjacency-changes (FabricPath)

To configure the log changes in the adjacency state, use the log-adjacency-changes command. To return to the default setting, use the no form of this command.

log-adjacency-changes

no log-adjacency-changes

Syntax Description

This command has no arguments or keywords.

Command Default

ON

Command Modes

FabricPath IS-IS configuration mode

Command History

Release	Modification
6.0(2)N1(1)	This command was introduced.

Usage Guidelines

This command requires an Enhanced Layer 2 license.

Examples

This example shows how to configure the log changes in the adjacency state:

switch# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

switch(config)# fabricpath domain default

switch(config-fabricpath-isis)# log-adjacency-changes

switch(config-fabricpath-isis)# 

Related Commands

Command	Description
show fabricpath isis	Displays FabricPath IS-IS information.

lsp-gen-interval (FabricPath)

To configure a link-state packet (LSP) generation interval, use the lsp-gen-interval command. To return to the default setting, use the no form of this command.

lsp-gen-interval {lsp-max-wait | lsp-initial-wait | lsp-second-wait}

no lsp-gen-interval {lsp-max-wait | lsp-initial-wait | lsp-second-wait}

Syntax Description

lsp-max-wait	Maximum interval (in seconds) between two consecutive occurrences of an LSP being generated. The range is from 50 to 120000. The default is 8000.
lsp-initial-wait	Initial LSP generation delay (in milliseconds). The range is from 50 to 120000. The default is 50.
lsp-second-wait	Hold time between the first and second LSP generation (in milliseconds). The range is from 50 to 120000. The default is 50.

Command Default

The defaults are as follows:

•lsp-max-wait: 8000

•lsp-initial-wait: 50

•lsp-second-wait: 50

Command Modes

FabricPath IS-IS configuration mode

Command History

Release	Modification
6.0(2)N1(1)	This command was introduced.

Usage Guidelines

You can enter the lsp-gen-interval command to control the rate of LSP packets being generated, transmitted, and retransmitted.

This command requires an Enhanced Layer 2 license.

Examples

This example shows how to configure an LSP-generation interval:

switch# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

switch(config)# fabricpath domain default

switch(config-fabricpath-isis)# lsp-gen-interval 9000 60 70

switch(config-fabricpath-isis)#

Related Commands

Command	Description
show fabricpath isis	Displays FabricPath IS-IS information.

lsp-mtu (FabricPath)

To configure a link-state packet (LSP) maximum transmission unit (MTU) that is generated by the Cisco Nexus 6000 software, use the lsp-mtu command. To return to the default setting, use the no form of this command.

lsp-mtu bytes

no lsp-mtu bytes

Syntax Description

bytes

Maximum LSP size in bytes. The range is from 128 to 4352.

Command Default

1492 bytes

Command Modes

FabricPath IS-IS configuration mode

Command History

Release	Modification
6.0(2)N1(1)	This command was introduced.

Usage Guidelines

This command requires an Enhanced Layer 2 license.

Examples

This example shows how to set the maximum LSP size to 1500 bytes:

switch# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

switch(config)# fabricpath domain default

switch(config-fabricpath-isis)# lsp-mtu 1500

switch(config-fabricpath-isis)#

Related Commands

Command	Description
show fabricpath isis	Displays FabricPath Layer 2 IS-IS.