Table Of Contents
C Commands
clear fabricpath isis adjacency
clear fabricpath isis statistics
clear fabricpath isis traffic
C Commands
This chapter describes the Cisco NX-OS FabricPath commands that begin with C.
clear fabricpath isis adjacency
To clear the FabricPath Layer 2 Intermediate-System to Intermediate-System (IS-IS) adjacency state, use the clear fabricpath isis adjacency command.
clear fabricpath isis adjacency [ * | ethernet slot/[QSFP-module]/port | port-channel
port_channel_number | system-id sid]
Syntax Description
*
|
(Optional) Specifies the IS-IS adjacencies on all interfaces.
|
ethernet
|
(Optional) Specifies the IS-IS adjacencies on an Ethernet interface.
|
slot
|
Slots from 1 to 8. The following list defines the slots available:
• Slots 1 to 4 are fixed Linecard Expansion Modules (LEMs).
•Slots 5 to 8 are hot-swappable LEMs.
|
QSFP-module
|
(Optional) The LEM that has been set to 10G mode. The QSFP-module number is from 1 to 12.
|
port
|
Port number within a particular slot. The port number is from 1 to 128.
|
port-channel
|
(Optional) Specifies the IS-IS adjacencies on a port-channel interface.
|
port_channel_number
|
(Optional) Port-channel number. The range is from 1 to 4096.
|
system-id
|
(Optional) Specifies the system ID.
|
sid
|
(Optional) System ID in the form of XXXX.XXXX.XXXX.
|
Command Default
None
Command Modes
EXEC mode
Command History
Release
|
Modification
|
6.0(2)N1(1)
|
This command was introduced.
|
Usage Guidelines
Note If you enter the * variable, you will affect forwarding by entering this command and might interrupt traffic; this command tears down all adjacencies.
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to clear the FabricPath Layer 2 adjacency state:
switch# clear fabricpath isis adjacency *
Related Commands
Command
|
Description
|
fabricpath domain default
|
Enables FabricPath Layer 2 IS-IS.
|
clear fabricpath isis statistics
To clear all FabricPath Intermediate System-to-Intermediate System (IS-IS) protocol statistics, use the clear fabricpath isis statistics command.
clear fabricpath isis statistics *
Syntax Description
*
|
Specifies the IS-IS adjacencies on all interfaces.
|
Command Default
None
Command Modes
EXEC mode
Command History
Release
|
Modification
|
6.0(2)N1(1)
|
This command was introduced.
|
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to clear FabricPath IS-IS protocol statistics:
switch# clear fabricpath isis statistics *
Related Commands
Command
|
Description
|
fabricpath domain default
|
Enables FabricPath Layer 2 IS-IS.
|
clear fabricpath isis traffic
To clear Intermediate System-to-Intermediate System (IS-IS) traffic information, use the clear fabricpath isis traffic command.
clear fabricpath isis traffic [* | ethernet module/slot/port | port-channel port_channel_number]
Syntax Description
*
|
(Optional) Specifies the IS-IS traffic on all interfaces.
|
ethernet
|
(Optional) Specifies the IS-IS traffic on an Ethernet interface.
|
module/slot/port
|
(Optional) Module, slot, and port numbers. The module range is from 1 to 255, the port is from 1 to 128, and the port range is from 1 to 48.
|
port-channel
|
(Optional) Specifies the IS-IS traffic on a port-channel interface.
|
port_channel_number
|
Port-channel number. The range is from 1 to 4096.
|
Command Default
None
Command Modes
EXEC mode
Command History
Release
|
Modification
|
6.0(2)N1(1)
|
This command was introduced.
|
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to clear FabricPath IS-IS traffic information:
switch# clear fabricpath isis traffic *
Related Commands
Command
|
Description
|
fabricpath domain default
|
Enables FabricPath Layer 2 IS-IS.
|
Feedback
