Feedback
Table Of Contents
network local messaging-gateway
N
Last Updated: April 16, 2010network local messaging-gateway
name
To assign a name to a system distribution list (SDL), use the name command in Cisco Unified Messaging Gateway (Cisco UMG) list manager edit mode. To clear the configuration, use the no form of this command.
name name
no name name
Syntax Description
name
Descriptive name used to identify the list. Enclose the name in double quotes if you use spaces.
Command Default
No name is specified.
Command Modes
Cisco UMG list manager edit (listmgr-edit)
Command History
Command History
Examples
The following example assigns the name "salesforce" to an SDL:
umg-1# config tumg-1(config)# list managerumg-1(listmgr)# list number 1234umg-1(listmgr-edit)# name salesforceumg-1(listmgr-edit)# member 408 555 0100 type subumg-1(listmgr-edit)# endumg-1(config)#Related Commands
nat location
To enter the NAT configuration mode to set up NAT entries on Cisco Unified Messaging Gateway (Cisco UMG) for an endpoint or for a messaging-gateway, use the nat location command in Cisco UMG configuration mode.
nat location location-id
Syntax Description
location-id
This is a numeric string that functions as a system-wide unique identifier (range: 1-10 digits).
Command Default
None
Command Modes
Cisco UMG configuration (config)
Command History
Usage Guidelines
If there is a NAT device in front of an endpoint or a peer messaging gateway, use this command to configure the local messaging gateway to use the external IP address on that NAT device when addressing that endpoint or messaging gateway.
If multiple messaging gateways are behind the same NAT device, endpoints should have the capability to talk to messaging gateways on ports other than just 80/25, because they may be sharing the same external IP address.
Examples
The following example illustrates the use of the nat location command:
umg-1# config tEnter configuration commands, one per line. End with CNTL/Z.umg-1(config)# nat location 777777umg-1(config-nat)# http external 192.0.2.24umg-1(config-nat)# endumg-1(config)# endumg-1# show nat location 777777Protocol Ext-IP Ext-Port----------------------------------------HTTP 209.165.200.224 26umg-1#Related Commands
ndr timeout
To configure a timeout window whose elapse will result in a non- delivery receipt (NDR), use the ndr command in Cisco Unified Messaging Gateway (Cisco UMG) configuration mode.
ndr timeout 1-48
Syntax Description
Command Default
6 hours
Command Modes
Cisco UMG configuration (config)
Command History
Usage Guidelines
Use this command to change the default settings.
Examples
The following example sets an NDR timeout:
umg# config t
umg(config)# ndr timeout 12umg(config)# exitumg# show ndr timeout
Timeout window for NDR is 12 hours
Related Commands
Configures a timeout window for a delayed delivery receipt (DDR).
Displays the NDR timeout window.
network default-route
To configure a default destination for messages that Cisco Unified Messaging Gateway (Cisco UMG) cannot deliver, use the network default-route command in Cisco UMG configuration mode. To clear the configuration, use the no form of this command.
network default-route location-id
no network default-route location-id
Syntax Description
location-id
This is a numeric string that functions as a system-wide unique identifier (range: 1-10 digits).
Command Default
None
Command Modes
Cisco UMG configuration (config)
Command History
Usage Guidelines
Use this command to set the default destination (either an endpoint or a peer messaging gateway) where a message is sent if the system cannot deliver it.
Examples
The following example illustrates the use of the network default-route command:
umg-1# configumg-1(config)# network default-route 777umg-1(config)# endumg-1# show network default-routeDefault route is location 777.umg-1#Related Commands
network local messaging-gateway
To set the location ID of the current configuring messaging gateway, use the network local messaging-gateway command in Cisco Unified Messaging Gateway (Cisco UMG) configuration mode. To clear the location ID, use the no form of this command.
network local messaging-gateway location-id
no network local messaging-gateway location-id
Syntax Description
location-id
This is a numeric string that functions as a system-wide unique identifier (range: 1-10 digits).
Command Default
None
Command Modes
Cisco UMG configuration (config)
Command History
Usage Guidelines
Use this command to set the location ID of the current configuring Cisco UMG.
Note
If you have more than one messaging gateway, you must configure them both as the local messaging gateway and as a peer (that is, from another messaging gateway).
Examples
umg-1# config tumg-1(config)# network local messaging-gateway 101umg-1(config)# endumg-1# show messaging-gatewayLocationID Hostname NAT------------------------------------------------------------5 sj.mycompany.com disabled55 sf.mycompany.com disabled555 ny.mycompany.com disabledLocal Gateway ID: 50000Related Commands
Configures a peer messaging gateway.
Displays all messaging gateways including the network peer messaging gateways and the current configuring messaging gateway.
network messaging-gateway
To configure a peer messaging gateway, use the network messaging-gateway command in Cisco Unified Messaging Gateway (Cisco UMG) configuration mode. To clear the configuration, use the no form of this command.
network messaging-gateway location-id hostname
no network messaging-gateway location-id hostname
Syntax Description
Command Default
None
Command Modes
Cisco UMG configuration (config)
Command History
Usage Guidelines
Use this command to specify location ID and hostname for a peer Cisco UMG.
Note
Specify one or more peer messaging gateways to ensure failover support for <Abbreviation>Cisco Unity Express and Cisco Unity systems.
You can add multiple peer Cisco UMGs to your system.
Note
Examples
The following example illustrates how the network messaging-gateway command is used:
umg-1# config tumg-1(config)# network messaging-gateway 101 peer-1.mycompany.comumg-1(config)# endumg-1# show messaging-gatewayLocationID Hostname NAT------------------------------------------------------------101 peer-1.mycompany.com disabledLocal Gateway ID: 51000umg-1#Related Commands
ntp server
To synchronize the clocks in the Cisco Unified Messaging Gateway (Cisco UMG) system by specifying an NTP server, use the ntp server command in Cisco UMG configuration mode. To delete the Cisco UMG router IP address and the NTP server name, use the no form of this command.
ntp server {hostname | ip-address} [prefer]
no ntp server {hostname | ip-address}
Syntax Description
hostname
Hostname of the NTP server.
ip-address
IP address of the NTP server.
prefer
(Optional) Marks the server as preferred.
Command Default
IP address of Cisco UMG.
Command Modes
Cisco UMG configuration
Command History
Usage Guidelines
Use this command to set the timing functions for your Cisco UMG system.
The prefer option indicates that the specified server is chosen for synchronization from among a set of correctly operating hosts.
Caution
Examples
The following example assigns the server with address 192.168.10.0 as the NTP server:
umg-1# enableumg-1# config tumg-1(config)# ntp server 192.168.10.0 preferThe following example assigns the server main_ntp as the NTP server:
umg-1 enableumg-1# config tumg-1(config)# ntp server main_ntpRelated Commands
