Feedback
Table Of Contents
C
Last Updated: April 16, 2010clear counters interfaces
To clear interface counters, use the clear counters interfaces command in Cisco Unified Messaging Gateway (Cisco UMG) EXEC mode.
clear counters interfaces
Syntax Description
This command has no arguments or keywords.
Command Default
None. Interface counters are not cleared.
Command Modes
Cisco UMG EXEC
Command History
Usage Guidelines
Use this command when you have interface counters you want to clear, for example, the general debug counters. This command clears all counters, including statistics counters.
Examples
The following example illustrates the use of the clear counters interfaces command.
umg-1> enableumg-1# clear counters interfacesumg-1# show interfaces ide 0IDE hd0 is up, line protocol is up0 reads, 0 bytes0 read errors0 write, 0 bytes0 write errorsumg-1#Related Commands
clear crashbuffer
To clear the kernel crash buffer, use the clear crashbuffer command in Cisco Unified Messaging Gateway (Cisco UMG) EXEC mode.
clear crashbuffer
Syntax Description
This command has no arguments or keywords.
Command Default
None. Crash buffer is not cleared.
Command Modes
Cisco UMG EXEC
Command History
Usage Guidelines
Use this command to clear the kernel crash buffer after the reasons for a crash are fully investigated.
Examples
The following example illustrates the use of the clear crashbuffer command.
umg-1 enable>umg-1# clear crashbufferumg-1#Related Commands
clear endpoint
To delete an autoregistered endpoint, use the clear endpoint command on the endpoint's primary messaging gateway in Cisco Unified Messaging Gateway (Cisco UMG) EXEC mode.
clear endpoint location-id
Syntax Description
Command Default
None
Command Modes
Cisco UMG EXEC
Command History
Usage Guidelines
•
After you have cleared an autoregistered endpoint, any messages it attempts to forward is rejected by Cisco UMG, although the endpoint does remain online.
•
•
•
Note
Examples
The following example illustrates the use of the clear endpoint command.
umg-1> enableumg-1# show endpoint localA total of 5 local endpoint(s) have been found:Location Location Endpoint Primary SecondaryID Prefix Type Gateway Gateway-----------------------------------------------------------------33 408108 CUE 50000 5900034 408109 CUE 5000035 408110 CUE 5000036 408111 CUE 5000037 408112 CUE 50000umg-1# clear endpoint 35Clear all data associated with endpoint 35 [confirm][OK]umg-1# show endpoint localA total of 4 local endpoint(s) have been found:Location Location Endpoint Primary SecondaryID Prefix Type Gateway Gateway-----------------------------------------------------------------33 408108 CUE 50000 5900034 408109 CUE 5000036 408111 CUE 5000037 408112 CUE 50000umg-1# show endpoint local 35Local endpoint with location id 35 has not been found.Related Commands
continue
To take Cisco Unified Messaging Gateway (Cisco UMG) from offline mode to online EXEC mode, use the continue command in Cisco UMG offline mode.
continue
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Cisco UMG offline
Command History
Usage Guidelines
This command returns Cisco UMG to online mode, for example, after a backup or restore procedure.
Examples
The following example illustrates the use of the continue command as a step in the backup procedure:
umg# offline!!!WARNING!!!: If you are going offline to do a backup, it is recommended that you save the current running configuration using the `write' command prior to going to the offline state.Putting the system offline will terminate all end user sessions.Are you sure you want to go offline[n]?: yumg(offline)# backup category allumg(offline)# continueumg#Related Commands
copy ftp
To copy a new configuration from an FTP server to another Cisco Unified Messaging Gateway (Cisco UMG) location, use the copy ftp command in Cisco UMG EXEC mode.
copy ftp: {nvram:startup-config | running-config | startup-config | system:running-config }
Syntax Description
Command Default
None
Command Modes
Cisco UMG EXEC
Command History
Usage Guidelines
When you copy from the FTP server, the copy ftp command becomes interactive and prompts you for the necessary information.
You may add a username and password to the server IP address if your server is not configured to accept anonymous FTP input. The format would be: userid:password@ftp-server-address/directory.
If you do not specify a directory value, the software uses the default FTP directory.
Note
Examples
The following example shows copying the configuration file named start from the FTP server in the default directory to the startup configuration in NVRAM:
umg# copy ftp: nvram:startup-configAddress or name or remote host? admin:messaging@192.0.2.24Source filename? startIn the following example, the file named start in the FTP server configs directory is copied to the startup configuration:
umg# copy ftp: startup-config!!!WARNING!!! This operation will overwrite your startup configuration.Do you wish to continue[y]? yAddress or name or remote host? admin:messaging@192.0.2.24configsSource filename? startRelated Commands
copy log
To copy the current logging information stored in the Cisco Unified Messaging Gateway (Cisco UMG) database to an FTP server, use the copy log command in Cisco UMG EXEC mode.
copy log {install.log | dmesg | syslog.log | atrace.log | klog.log | debug_server.log | messages.log} url ftp://[user-id:ftp-password@]ftp-server-address[/directory]/filename
Syntax Description
Command Default
None
Command Modes
Cisco UMG EXEC
Command History
Usage Guidelines
If you do not specify a directory value, the software uses the default FTP directory.
Examples
The following example shows copying the install log data to the default directory on the FTP server and saving the data in the file installinfo.
umg# copy log install.log url ftp://admin:umg@192.0.2.24/lnstallinfoumg#Related Commands
copy running-config
To copy the running configuration to another destination, use the copy running-config command in Cisco Unified Messaging Gateway (Cisco UMG) EXEC mode.
copy running-config {ftp: | nvram:startup-config filename | startup-config | tftp:}
Syntax Description
Command Default
None
Command Modes
Cisco UMG EXEC
Command History
Usage Guidelines
When you copy to an FTP or TFTP server, the copy running-config command becomes interactive and prompts you for the necessary information. You may add a username and password to the server IP address if your server is not configured to accept anonymous FTP input. The format would be: userid:password@ftp-server-address/directory. If you do not specify a directory value, the software uses the default FTP directory.
Note
Examples
In the following example, the running configuration is copied to the FTP server, which requires a username and password and has an IP address of 192.0.2.24. The running configuration is copied to the configs directory as file saved_start.
umg# copy running-config ftp:Address or name of remote host? admin:messaging@192.0.2.24/configsSource filename? saved_startThe following example shows the running configuration copied to the NVRAM saved configuration as filename startup:
umg# copy running-config nvram:startup-config startupThe following example shows the running configuration copied to the startup configuration as filename start:
umg# copy running-config startup-config startThe following example shows the running configuration copied to the TFTP server as filename temp_start:
umg# copy running-config tftp:Address or name of remote host? 192.0.2.24Source filename? temp_startRelated Commands
copy startup-config
To copy the startup configuration to another destination, use the copy startup-config command in Cisco Unified Messaging Gateway (Cisco UMG) EXEC mode.
copy startup-config {ftp: | tftp: }
Syntax Description
Command Default
None
Command Modes
Cisco UMG EXEC
Command History
Usage Guidelines
When you copy to an FTP or TFTP server, the copy startup-config command becomes interactive and prompts you for the necessary information. You may add a username and password to the server IP address if your server is not configured to accept anonymous FTP input. The format would be: userid:password@ftp-server-address/directory. If you do not specify a directory value, the software uses the default FTP directory.
Note
Examples
In the following example, the startup configuration is copied to the FTP server, which requires a username and password and has an IP address of 192.0.2.24. The startup configuration is copied to the configs directory as file saved_start.
umg# copy startup-config ftp:Address or name of remote host? admin:messaging@192.0.2.24/configsSource filename? saved_startThe following example shows the startup configuration being copied to the TFTP server as filename temp_start:
umg# copy startup-config tftp:Address or name of remote host? 192.0.2.24Source filename? temp_startRelated Commands
copy tftp
To copy the network TFTP server information to another destination, use the copy tftp command in Cisco Unified Messaging Gateway EXEC mode.
copy tftp: {nvram:startup-config | running-config | startup-config | system:running-config}
Syntax Description
Command Modes
Cisco UMG EXEC
Command History
Usage Guidelines
The copy tftp command is an interactive command and prompts you for the necessary information. You may add a username and password to the server IP address if your server is not configured to accept anonymous TFTP input. The format would be: userid:password@ftp-server-address/directory. If you do not specify a directory value, the software uses the default TFTP directory.
Copying a startup configuration from the TFTP server to the startup configuration overwrites the startup configuration. Cisco UMG displays a warning that asks you to confirm the overwrite.
Note
Examples
The following example shows a TFTP server with the IP address 192.0.2.24. The TFTP server data in the source filename start is copied to the running configuration.
umg# copy tftp: running-configAddress or name of remote host? 192.0.2.24Source filename? startIn the following example, the TFTP server has the IP address 192.0.2.24. The file start in directory configs on the TFTP server is copied to the startup configuration.
umg# copy tftp: startup-config!!!WARNING!!! This operation will overwrite your startup configuration.Do you wish to continue[y]? yAddress or name of remote host? 192.0.2.24/configsSource filename? startRelated Commands
