Cisco Unified Serviceability Administration Guide, Release 7.0(1) - Configuring SNMP Trap/Inform Parameters [Cisco Unified Communications Manager (CallManager)]

Table Of Contents

Configuring SNMP Trap/Inform Parameters

Configuring CISCO-SYSLOG-MIB Trap Parameters

Configuring CISCO-CCM-MIB Trap Parameters

Where to Find More Information

Configuring SNMP Trap/Inform Parameters

This section describes how to use CLI commands to set configurable trap settings. Table 14-3 provides the SNMP trap configuration parameters and recommended configuration for CISCO-SYSLOG-MIB and CISCO-CCM-MIB.

This chapter provides information on the following topics:

•Configuring CISCO-SYSLOG-MIB Trap Parameters

•Configuring CISCO-CCM-MIB Trap Parameters

Configuring CISCO-SYSLOG-MIB Trap Parameters

Unified CM and Unified CM BE only: Use these guidelines to configure CISCO-SYSLOG-MIB trap settings on your system:

•Set clogsNotificationEnabled (1.3.6.1.4.1.9.9.41.1.1.2) to true by using the SNMP Set operation; for example, use the net-snmp set utility to set this OID to true from the linux command line using: snmpset -c <community string> -v2c <transmitter ipaddress> 1.3.6.1.4.1.9.9.41.1.1.2.0 i 1

You can also use any other SNMP management application for the SNMP Set operation.

•Set clogMaxSeverity (1.3.6.1.4.1.9.9.41.1.1.3) value by using the SNMP Set operation; for example, use the net-snmp set utility to set this OID value from the linux command line using: snmpset -c public -v2c 1<transmitter ipaddress> 1.3.6.1.4.1.9.9.41.1.1.3.0 i <value>

Enter a severity number for the <value> setting. Severity values increase as severity decreases. A value of 1 (Emergency) indicates highest severity, and a value of 8 (Debug) indicates lowest severity. Syslog agent ignores any messages greater than the value that you specify; for example, to trap all syslog messages, use a value of 8.

You can also use any other SNMP management application for the SNMP Set operation.

Note Before logging, Syslog truncates any trap message data that is larger than the specified Syslog buffer size. The Syslog trap message length limitation equals 255 bytes.

Configuring CISCO-CCM-MIB Trap Parameters

Unified CM and Unified CM BE only: Use these guidelines to configure CISCO-CCM-MIB trap settings on your system:

•Set ccmPhoneFailedAlarmInterval (1.3.6.1.4.1. 9.9.156.1.9.2 to a value in the range 30-3600 by using the SNMP Set operation; for example, use the net-snmp set utility to set this OID value from the linux command line using: snmpset -c <community string> -v2c <transmitter ipaddress> 1.3.6.1.4.1.9.9.156.1.9.2 .0 i <value>

You can also use any other SNMP management application for the SNMP Set operation.

•Set ccmPhoneStatusUpdateAlarmInterval (1.3.6.1.4.1.9.9.156.1.9.4) to a value in the range 30-3600 by using the SNMP Set operation; for example, use the net-snmp set utility to set this OID value from the linux command line using: snmpset -c <community string> -v2c <transmitter ipaddress> 1.3.6.1.4.1.9.9.156.1.9.4.0 i <value>

You can also use any other SNMP management application for the SNMP Set operation.

Where to Find More Information

Related Topics

•Understanding Services, page 9-1

•Configuring Services, page 11-1

•Configuring SNMP Trap/Inform Parameters

•Configuring SNMP V1/V2c, page 15-1

•Configuring SNMP V3, page 16-1

•Configuring SNMP System Group, page 17-1

•Troubleshooting, page 19-1

Related Documentation

Command Line Interface Reference Guide for Cisco Unified Solutions

	Cisco Unified Serviceability Administration Guide, Release 7.0(1)
	Configuring SNMP Trap/Inform Parameters
Cisco Unified Serviceability Administration Guide, Release 7.0(1) Index Preface Cisco Unified Serviceability Understanding Cisco Unified Serviceability Using Cisco Unified Serviceability Alarms Understanding Alarms Configuring Alarms Viewing and Updating Alarm Definitions Trace Understanding Trace Configuring Trace Configuring Troubleshooting Trace Setting Tools Understanding Services Understanding Serviceability Reports Archive Configuring Services Configuring Serviceability Reports Archive Configuring CDR Repository Manager Simple Network Management Protocol (SNMP) Understanding Simple Network Management Protocol Configuring SNMP V1/V2c Configuring SNMP V3 Configuring the SNMP System Group Configuring SNMP Trap/Inform Parameters SNMP Troubleshooting	Download this chapter Configuring SNMP Trap/Inform Parameters Download the complete book Cisco Unified Serviceability Administration Guide, Release 7.0(1) (PDF - 3 MB) Feedback Table Of Contents Configuring SNMP Trap/Inform Parameters Configuring CISCO-SYSLOG-MIB Trap Parameters Configuring CISCO-CCM-MIB Trap Parameters Where to Find More Information Configuring SNMP Trap/Inform Parameters This section describes how to use CLI commands to set configurable trap settings. Table 14-3 provides the SNMP trap configuration parameters and recommended configuration for CISCO-SYSLOG-MIB and CISCO-CCM-MIB. This chapter provides information on the following topics: •Configuring CISCO-SYSLOG-MIB Trap Parameters •Configuring CISCO-CCM-MIB Trap Parameters Configuring CISCO-SYSLOG-MIB Trap Parameters Unified CM and Unified CM BE only: Use these guidelines to configure CISCO-SYSLOG-MIB trap settings on your system: •Set clogsNotificationEnabled (1.3.6.1.4.1.9.9.41.1.1.2) to true by using the SNMP Set operation; for example, use the net-snmp set utility to set this OID to true from the linux command line using: snmpset -c <community string> -v2c <transmitter ipaddress> 1.3.6.1.4.1.9.9.41.1.1.2.0 i 1 You can also use any other SNMP management application for the SNMP Set operation. •Set clogMaxSeverity (1.3.6.1.4.1.9.9.41.1.1.3) value by using the SNMP Set operation; for example, use the net-snmp set utility to set this OID value from the linux command line using: snmpset -c public -v2c 1<transmitter ipaddress> 1.3.6.1.4.1.9.9.41.1.1.3.0 i <value> Enter a severity number for the <value> setting. Severity values increase as severity decreases. A value of 1 (Emergency) indicates highest severity, and a value of 8 (Debug) indicates lowest severity. Syslog agent ignores any messages greater than the value that you specify; for example, to trap all syslog messages, use a value of 8. You can also use any other SNMP management application for the SNMP Set operation. Note Before logging, Syslog truncates any trap message data that is larger than the specified Syslog buffer size. The Syslog trap message length limitation equals 255 bytes. Configuring CISCO-CCM-MIB Trap Parameters Unified CM and Unified CM BE only: Use these guidelines to configure CISCO-CCM-MIB trap settings on your system: •Set ccmPhoneFailedAlarmInterval (1.3.6.1.4.1. 9.9.156.1.9.2 to a value in the range 30-3600 by using the SNMP Set operation; for example, use the net-snmp set utility to set this OID value from the linux command line using: snmpset -c <community string> -v2c <transmitter ipaddress> 1.3.6.1.4.1.9.9.156.1.9.2 .0 i <value> You can also use any other SNMP management application for the SNMP Set operation. •Set ccmPhoneStatusUpdateAlarmInterval (1.3.6.1.4.1.9.9.156.1.9.4) to a value in the range 30-3600 by using the SNMP Set operation; for example, use the net-snmp set utility to set this OID value from the linux command line using: snmpset -c <community string> -v2c <transmitter ipaddress> 1.3.6.1.4.1.9.9.156.1.9.4.0 i <value> You can also use any other SNMP management application for the SNMP Set operation. Where to Find More Information Related Topics •Understanding Services, page 9-1 •Configuring Services, page 11-1 •Configuring SNMP Trap/Inform Parameters •Configuring SNMP V1/V2c, page 15-1 •Configuring SNMP V3, page 16-1 •Configuring SNMP System Group, page 17-1 •Troubleshooting, page 19-1 Related Documentation Command Line Interface Reference Guide for Cisco Unified Solutions
	Terms & Conditions \| Privacy Statement \| Cookie Policy \| Trademarks