Feedback
Table Of Contents
switchport private-vlan host-association
switchport private-vlan mapping
switchport private-vlan mapping trunk
S Commands
This chapter describes the Cisco Nexus 1000V commands that begin with the letter S.
send
To send a message to an open session, use the send command.
send {message | session device message}
Syntax Description
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
network-operatorCommand History
Examples
This example shows how to send a message to an open session:
n1000v# send session sessionOne testingn1000v#Related Commands
session-limit
To limit the number of VSH sessions, use the session-limit command. To remove the limit, use the no form of this command.
session-limit number
no session-limit number
Syntax Description
Defaults
No limit is set.
Command Modes
Line configuration (config-line)
Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to limit the number of VSH sessions:
n1000v# configure terminaln1000v(config)# line vtyn1000v(config-line)# session-limit 10n1000v(config-line)#This example shows how to remove the limit:
n1000v# configure terminaln1000v(config)# line vtyn1000v(config-line)# no session-limit 10n1000v(config-line)#service-policy
To configure a service policy for an interface, use the service-policy command. To remove the service policy configuration, use the no form of this command.
service-policy {input name [no-stats] | output name [no-stats] | type qos {input name [no-stats] | output name [no-stats]}}
no service-policy {input name [no-stats] | output name [no-stats] | type qos {input name [no-stats] | output name [no-stats]}}
Syntax Description
Defaults
No service policy exists.
Command Modes
Interface Configuration (config-if)
Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to configure a service policy for an interface:
n1000v# configure terminaln1000v(config)# interface vethernet 10n1000v(config-if)# service-policy type qos input sp10 no-statsn1000v(config-if)#This example shows how to remove a service policy configuration for an interface:
n1000v# configure terminaln1000v(config)# interface vethernet 10n1000v(config-if)# no service-policy type qos input sp10 no-statsn1000v(config-if)#Related Commands
set
To set QoS class attributes, use the set command. To remove class attributes, use the no form of this command.
set {{cos cos-val} | {dscp [tunnel] {dscp-val | dscp-enum}} | {precedence [tunnel] {prec-val | prec-enum}} | {discard-class dis-class-val} | {qos-group qos-grp-val} | {{{cos cos} | {dscp dscp} | {precedence precedence} | {discard-class discard-class}} table table-map-name} | {cos1 {{dscp table cos-dscp-map} | {precedence table cos-precedence-map} | {discard-class table cos-discard-class-map}}} | {dscp1 {{cos table dscp-cos-map} | {prec3 table dscp-precedence-map} | {dis-class3 table dscp-discard-class-map}}} | {prec1 {{cos3 table precedence-cos-map} | {dscp3 table precedence-dscp-map} | {dis-class3 table precedence-discard-class-map}}} | {dis-class1 {{cos3 table discard-class-cos-map} | {dscp3 table discard-class-dscp-map} | {prec3 table discard-class-precedence-map}}}}
no set {{cos cos-val} | {dscp [tunnel] {dscp-val | dscp-enum}} | {precedence [tunnel] {prec-val | prec-enum}} | {discard-class dis-class-val} | {qos-group qos-grp-val} | {{{cos cos} | {dscp dscp} | {precedence precedence} | {discard-class discard-class}} table table-map-name} | {cos1 {{dscp table cos-dscp-map} | {precedence table cos-precedence-map} | {discard-class table cos-discard-class-map}}} | {dscp1 {{cos table dscp-cos-map} | {prec3 table dscp-precedence-map} | {dis-class3 table dscp-discard-class-map}}} | {prec1 {{cos3 table precedence-cos-map} | {dscp3 table precedence-dscp-map} | {dis-class3 table precedence-discard-class-map}}} | {dis-class1 {{cos3 table discard-class-cos-map} | {dscp3 table discard-class-dscp-map} | {prec3 table discard-class-precedence-map}}}}
Syntax Description
Defaults
None
Command Modes
Policy Map Class Configuration (config-pmap-c-qos)
Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to set class attributes:
n1000v# configure terminaln1000v(config)# policy-map pm1n1000v(config-pmap-qos)# class class-defaultn1000v(config-pmap-c-qos)# set qos-group 1n1000v(config-pmap-c-qos)#This example shows how to remove class attributes:
n1000v# configure terminaln1000v(config)# policy-map pm1n1000v(config-pmap-qos)# class class-defaultn1000v(config-pmap-c-qos)# no set qos-group 1n1000v(config-pmap-c-qos)#Related Commands
setup
To use the Basic System Configuration Dialog for creating or modifying your system configuration file, use the setup command.
setup
Syntax Description
This command has no arguments or keywords, but the Basic System Configuration Dialog prompts you for complete setup information (see the example below).
Defaults
None
Command Modes
Any
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
The Basic System Configuration Dialog assumes the factory defaults. Keep this in mind when using it to modify an existing configuration.
All changes made to your configuration are summarized for you at the completion of the setup sequence with an option to save the changes or not.
You can exit the setup sequence at any point by pressing Ctrl-C.
Examples
This example shows how to use the setup command to create or modify a basic system configuration:
n1000v# setupEnter the domain id<1-4095>: 400Enter HA role[standalone/primary/secondary]: standalone[########################################] 100%---- Basic System Configuration Dialog ----This setup utility will guide you through the basic configuration ofthe system. Setup configures only enough connectivity for managementof the system.*Note: setup is mainly used for configuring the system initially,when no configuration is present. So setup always assumes systemdefaults and not the current system configuration values.Press Enter at anytime to skip a dialog. Use ctrl-c at anytimeto skip the remaining dialogs.Would you like to enter the basic configuration dialog (yes/no): yCreate another login account (yes/no) [n]: nConfigure read-only SNMP community string (yes/no) [n]: nConfigure read-write SNMP community string (yes/no) [n]: nEnter the switch name : n1000vContinue with Out-of-band (mgmt0) management configuration? (yes/no) [y]:Mgmt0 IPv4 address :Configure the default gateway? (yes/no) [y]: nConfigure advanced IP options? (yes/no) [n]:Enable the telnet service? (yes/no) [y]:Enable the ssh service? (yes/no) [n]:Configure the ntp server? (yes/no) [n]:Configure vem feature level? (yes/no) [n]:Configure svs domain parameters? (yes/no) [y]:Enter SVS Control mode (L2 / L3) : l2Invalid SVS Control ModeEnter SVS Control mode (L2 / L3) : L2Enter control vlan <1-3967, 4048-4093> : 400Enter packet vlan <1-3967, 4048-4093> : 405The following configuration will be applied:switchname n1000vtelnet server enableno ssh server enablesvs-domainsvs mode L2control vlan 400packet vlan 405domain id 400vlan 400vlan 405Would you like to edit the configuration? (yes/no) [n]:Use this configuration and save it? (yes/no) [y]: nn1000v#Related Commands
shutdown
To shutdown VLAN switching, use the shutdown command. To turn on VLAN switching, use the no form of this command.
shutdown
no shutdown
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
VLAN configuration (config-vlan)
Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to shutdown VLAN switching:
n1000v# configure terminaln1000v(config)# vlan 10n1000v(config-vlan)# shutdownn1000v(config-vlan)#This example shows how to turn on VLAN switching:
n1000v# configure terminaln1000v(config)# vlan 10n1000v(config-vlan)# no shutdownn1000v(config-vlan)#Related Commands
sleep
To set a sleep time, use the sleep command.
sleep time
Syntax Description
Defaults
Sleep time is not set.
Command Modes
Any
Supported User Rolesnetwork-admin
network-operatorCommand History
Usage Guidelines
When you set time to 0, sleep is disabled.
Examples
This example shows how to set a sleep time:
n1000v# sleep 100n1000v#This example shows how to disable sleep:
n1000v# sleep 0n1000v#ssh
To create a Secure Shell (SSH) session, use the ssh command.
ssh [username@]{ipv4-address | hostname} [vrf vrf-name]
Syntax Description
Defaults
Default VRF
Command Modes
Any
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
The NX-OS software supports SSH version 2.
Examples
This example shows how to start an SSH session:
n1000v# ssh 10.10.1.1 vrf managementThe authenticity of host '10.10.1.1 (10.10.1.1)' can't be established.RSA key fingerprint is 9b:d9:09:97:f6:40:76:89:05:15:42:6b:12:48:0f:d6.Are you sure you want to continue connecting (yes/no)? yesWarning: Permanently added '10.10.1.1' (RSA) to the list of known hosts.User Access VerificationPassword:Related Commands
clear ssh session
Clears SSH sessions.
ssh server enable
Enables the SSH server.
ssh key
To create a Secure Shell (SSH) server key for a virtual device context (VDC), use the ssh key command. To remove the SSH server key, use the no form of this command.
ssh key {dsa [force] | rsa [length [force]]}
no ssh key [dsa | rsa]
Syntax Description
Defaults
1024-bit length
Command Modes
Global Configuration (config)
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
The NX-OS software supports SSH version 2.
If you want to remove or replace an SSH server key, you must first disable the SSH server using the no ssh server enable command.
Examples
This example shows how to create an SSH server key using DSA:
n1000v# config tn1000v(config)# ssh key dsagenerating dsa key(1024 bits).......generated dsa keyThis example shows how to create an SSH server key using RSA with the default key length:
n1000v# config tn1000v(config)# ssh key rsagenerating rsa key(1024 bits)......generated rsa keyThis example shows how to create an SSH server key using RSA with a specified key length:
n1000v# config tn1000v(config)# ssh key rsa 768generating rsa key(768 bits)......generated rsa keyThis example shows how to replace an SSH server key using DSA with the force option:
n1000v# config tn1000v(config)# no ssh server enablen1000v(config)# ssh key dsa forcedeleting old dsa key.....generating dsa key(1024 bits)......generated dsa keyn1000v(config)# ssh server enableThis example shows how to remove the DSA SSH server key:
n1000v# config tn1000v(config)# no ssh server enableXML interface to system may become unavailable since ssh is disabledn1000v(config)# no ssh key dsan1000v(config)# ssh server enableThis example shows how to remove all SSH server keys:
n1000v# config tn1000v(config)# no ssh server enableXML interface to system may become unavailable since ssh is disabledn1000v(config)# no ssh keyn1000v(config)# ssh server enableRelated Commands
show ssh key
Displays the SSH server key information.
ssh server enable
Enables the SSH server.
ssh server enable
To enable the Secure Shell (SSH) server, use the ssh server enable command. To disable the SSH server, use the no form of this command.
ssh server enable
no ssh server enable
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global Configuration (config)
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
The NX-OS software supports SSH version 2.
Examples
This example shows how to enable the SSH server:
n1000v# config tn1000v(config)# ssh server enableThis example shows how to disable the SSH server:
n1000v# config tn1000v(config)# no ssh server enableXML interface to system may become unavailable since ssh is disabledRelated Commands
state (VLAN)
To set the operational state of a VLAN, use the state command. To disable state configuration, use the no form of this command.
state {active | suspend}
no state
Syntax Description
Defaults
None
Command Modes
VLAN configuration (config-vlan)
Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to set the operational state of a VLAN:
n1000v# configure terminaln1000v(config)# vlan 10n1000v(config-vlan)# state activen1000v(config-vlan)#This example shows how to disable state configuration:
n1000v# configure terminaln1000v(config)# vlan 10n1000v(config-vlan)# no staten1000v(config-vlan)#Related Commands
state (Port Profile)
To set the operational state of a port profile, use the state command.
state enabled
Syntax Description
Defaults
Disabled
Command Modes
Port profile configuration (config-port-prof)
Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to enable or disable the operational state of a port profile:
n1000v# configure terminaln1000v(config)# port-profile testprofilen1000v(config-port-prof)# state enabledn1000v(config-port-prof)#Related Commands
statistics per-entry
To collect statistics for each ACL entry, use the statistics per-entry command. To remove statistics, use the no form of this command.
statistics per-entry
no statistics per-entry
Syntax Description
This command has no arguments or keywords.
Defaults
No statistics are collected.
Command Modes
ACL configuration (config-acl)
Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to collect statistics for each ACL entry:
n1000v# configure terminaln1000v(config)# ip access-list 1n1000v(config-acl)# statistics per-entryn1000v(config-acl)#This example shows how to remove statistics:
n1000v# configure terminaln1000v(config)# ip access-list 1n1000v(config-acl)# no statistics per-entryn1000v(config-acl)#Related Commands
svs connection
To enable an SVS connection, use the svs connection command. To disable an SVS connection, use the no form of this command.
svs connection name
no svs connection name
Syntax Description
Defaults
None
Command Modes
Global Configuration (config)
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
Only one SVS connection can be enabled per session.
Examples
This example shows how to enable an SVS connection:
n1000v# configure terminaln1000v(config)# svs connection conn1n1000v(config-svs-conn)#This example shows how to disable an SVS connection:
n1000v# configure terminaln1000v(config)# no svs connection conn1n1000v(config)#Related Commands
svs-domain
To configure an SVS domain and enter SVS domain configuration mode, use the svs-domain command.
svs-domain
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Global Configuration (config)
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
Examples
This example shows how to enter SVS domain configuration mode to configure an SVS domain:
n1000v# configure terminaln1000v(config)# svs-domainn1000v(config-svs-domain)#Related Commands
svs license transfer src-vem
To transfer licenses from a specified source VEM to another VEM, or to transfer an unused license to the VSM license pool, use the svs license transfer src-vem command.
svs license transfer src-vem module number [ dst-vem module number | license_pool ]
Syntax Description
dst-vem module-number
Specifies the VEM to receive the transferred license.
license_pool
Transfers a license back to the VSM license pool.
Defaults
None
Command Modes
Global Configuration (config)
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
•
Licenses cannot be transferred to a VEM unless there are sufficient licenses in the pool for all CPUs on that VEM.
•
–
–
•
–
Examples
This example shows how to transfer a license from VEM 3 to VEM 5, and then display the license configuration:
n1000v# config t
n1000v(config)# svs license transfer src-vem 3 dst-vem 5n1000v(config)# show license usage NEXUS1000V_LAN_SERVICES_PKGApplication-----------VEM 5 - Socket 1VEM 5 - Socket 2VEM 4 - Socket 1VEM 4 - Socket 2-----------n1000v#This example shows how to transfer a license from VEM 3 to the VSM license pool, and then display the license configuration:
n1000v# config t
n1000v(config)# svs license transfer src-vem 3 license_pool
n1000v(config)# show license usage NEXUS1000V_LAN_SERVICES_PKGApplication-----------VEM 4 - Socket 1VEM 4 - Socket 2-----------n1000v#Related Commands
svs license volatile
To enable volatile licenses so that, whenever a VEM is taken out of service, its licenses are returned to the VSM pool of available licenses, use the svs license volatile command. To disable volatile licenses, use the no form of this command.
svs license volatile
no svs license volatile
Syntax Description
This command has no arguments or keywords.
Defaults
Disabled
Command Modes
Global Configuration (config)
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
Caution
Volatile licenses are removed from a VEM during a loss in connectivity and are not returned to the VEM when connectivity resumes. Cisco recommends that the volatile license feature remain disabled and that you, instead, transfer unused licenses using the svs license transfer src-vem command.
Examples
This example shows how to enable the volatile license feature for a VSM:
n1000v(config)# svs license volatile
n1000v(config)#
This example shows how to disable the volatile license feature for a VSM:
n1000v(config)# no svs license volatileRelated Commands
switchname
To configure the hostname for the device, use the switchname command. To revert to the default, use the no form of this command.
switchname name
no switchname
Syntax Description
name
Name for the device. The name is alphanumeric, case sensitive, can contain special characters, and can have a maximum of 32 characters.
Defaults
switch
Command Modes
Global Configuration (config)
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
The Cisco NX-OS software uses the hostname in command-line interface (CLI) prompts and in default configuration filenames.
The switchname command performs the same function as the hostname command.
Examples
This example shows how to configure the device hostname:
n1000v# configure terminaln1000v(config)# switchname Engineering2Engineering2(config)#This example shows how to revert to the default device hostname:
Engineering2# configure terminalEngineering2(config)# no switchnamen1000v(config)#
Related Commands
hostname
Configures the device hostname.
show switchname
Displays the device hostname.
switchport access vlan
To set the access mode of an interface, use the switchport access vlan command. To remove access mode configuration, use the no form of this command.
switchport access vlan id
no switchport access vlan
Syntax Description
Defaults
Access mode is not set.
Command Modes
Interface Configuration (config-if)
Port Profile Configuration (config-port-prof)Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to set the access mode of an interface:
n1000v# configure terminaln1000v(config)# interface vethernet 1n1000v(config-if)# switchport access vlan 10n1000v(config-if)#This example shows how to remove access mode configuration:
n1000v# configure terminaln1000v(config)# interface vethernet 1n1000v(config-if)# no switchport access vlann1000v(config-if)#Related Commands
switchport mode
To set the port mode of an interface, use the switchport mode command. To remove the port mode configuration, use the no form of this command.
switchport mode {access | private-vlan {host | promiscuous} | trunk}
no switchport mode {access | private-vlan {host | promiscuous} | trunk}
Syntax Description
Defaults
Switchport mode is not set.
Command Modes
Interface Configuration (config-if)
Port Profile Configuration (config-port-prof)Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to set the port mode of an interfn1000vace:
n1000v# configure terminaln1000v(config)# interface vethernet 1n1000v(config-if)# switchport mode private-vlan hostn1000v(config-if)#This example shows how to remove mode configuration:
n1000v# configure terminaln1000v(config)# interface vethernet 1n1000v(config-if)# no switchport mode private-vlan hostn1000v(config-if)#Related Commands
switchport port-security
To set the port security characteristics of an interface, use the switchport port-security command. To remove the port security configuration, use the no form of this command.
switchport port-security [aging {time time | type {absolute | inactivity}} | mac-address {address [vlan id] |sticky} | maximum number [vlan id] | violation {protect | shutdown}]
no switchport port-security [aging {time time | type {absolute | inactivity}} | mac-address {address [vlan id] |sticky} | maximum number [vlan id] | violation {protect | shutdown}]}
Syntax Description
Defaults
None
Command Modes
Interface Configuration (config-if)
Port Profile Configuration (config-port-prof)Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to set the port security aging inactivity timer:
n1000v# configure terminaln1000v(config)# interface vethernet 1n1000v(config-if)# switchport port-security aging type inactivityn1000v(config-if)#This example shows how to remove the port security aging inactivity timer:
n1000v# configure terminaln1000v(config)# interface vethernet 1n1000v(config-if)# no switchport port-security aging type inactivityn1000v(config-if)#Related Commands
show interface
Displays interface information.
show port-security
Displays port security information.
switchport private-vlan host-association
To define a private VLAN association for an isolated or community port, use the switchport private-vlan host-association command. To remove the private VLAN association from the port, use the no form of this command.
switchport private-vlan host-association {primary-vlan-id} {secondary-vlan-id}
no switchport private-vlan host-association
Syntax Description
primary-vlan-id
Number of the primary VLAN of the private VLAN relationship.
secondary-vlan-id
Number of the secondary VLAN of the private VLAN relationship.
Defaults
None
Command Modes
Interface Configuration (config-if)
Port Profile Configuration (config-port-prof)Supported User Rolesnetwork-admin
Command History
Usage Guidelines
There is no run-time effect on the port unless it is in private VLAN-host mode. If the port is in private VLAN-host mode but neither of the VLANs exist, the command is allowed but the port is made inactive. The port also may be inactive when the association between the private VLANs is suspended.
The secondary VLAN may be an isolated or community VLAN.
Examples
This example shows how to configure a host private VLAN port with a primary VLAN (VLAN 18) and a secondary VLAN (VLAN 20):
n1000v(config-if)# switchport private-vlan host-association 18 20n1000v(config-if)#This example shows how to remove the private VLAN association from the port:
n1000v(config-if)# no switchport private-vlan host-associationn1000v(config-if)#Related Commands
switchport private-vlan mapping
To define the private VLAN association for a promiscuous port, use the switchport private-vlan mapping command. To clear all mapping from the primary VLAN, use the no form of this command.
switchport private-vlan mapping {primary-vlan-id} {[add] secondary-vlan-list | remove secondary-vlan-list}
no switchport private-vlan mapping
Syntax Description
Defaults
None
Command Modes
Interface Configuration (config-if)
Port Profile Configuration (config-port-prof)Supported User Rolesnetwork-admin
Command History
Usage Guidelines
There is no run-time effect on the port unless it is in private VLAN-promiscuous mode. If the port is in private VLAN-promiscuous mode but the primary VLAN does not exist, the command is allowed but the port is made inactive.
The secondary VLAN may be an isolated or community VLAN.
Examples
This example shows how to configure the associate primary VLAN 18 to secondary isolated VLAN 20 on a private VLAN promiscuous port:
n1000v(config-if)# switchport private-vlan mapping 18 20n1000v(config-if)#This example shows how to add a VLAN to the association on the promiscuous port:
n1000v(config-if)# switchport private-vlan mapping 18 add 21n1000v(config-if)#This example shows how to remove the all private VLAN association from the port:
n1000v(config-if)# no switchport private-vlan mappingn1000v(config-if)#
Related Commands
switchport private-vlan mapping trunk
To designate the primary private VLAN, use the switchport private-vlan trunk mapping trunk command. To remove the primary private VLAN, use the no form of this command.
switchport private-vlan trunk native vlan id
no switchport private-vlan trunk native vlan
Syntax Description
Defaults
None
Command Modes
Interface Configuration (config-if)
Port Profile Configuration (config-port-prof)Supported User Rolesnetwork-admin
Command History
Usage Guidelines
When you use this command, you must either add a secondary VLAN, or remove a VLAN.
Examples
This example shows how to designate the primary private VLAN:
n1000v# configure terminaln1000v(config)# interface vethernet 1n1000v(config-if)# n1000v(config-if)# switchport private-vlan mapping trunk 10 add 11n1000v(config-if)#This example shows how to remove the primary private VLAN:
n1000v# configure terminaln1000v(config)# interface vethernet 1n1000v(config-if)# n1000v(config-if)# no switchport private-vlan mapping trunk 10n1000v(config-if)#Related Commands
switchport trunk allowed vlan
To set the list of allowed VLANs on the trunking interface, use the switchport trunk allowed vlan command. To allow all VLANs on the trunking interface, use the no form of this command.
switchport trunk allowed vlan {vlan-list | all | none | [add | except | remove {vlan-list}]}
no switchport trunk allowed vlan
Syntax Description
Defaults
All VLANs
Command Modes
Interface Configuration (config-if)
Port Profile Configuration (config-port-prof)Supported User Rolesnetwork-admin
Command History
Usage Guidelines
You must enter the switchport command without any keywords to configure the LAN interface as a Layer 2 interface before you can enter the switchport trunk allowed vlan command. This action is required only if you have not entered the switchport command for the interface.
If you remove VLAN 1 from a trunk, the trunk interface continues to send and receive management traffic in VLAN 1.
Examples
This example shows how to add a series of consecutive VLANs to the list of allowed VLANs on a trunking port:
n1000v(config-if)# switchport trunk allowed vlan add 40-50n1000v(config-if)#Related Commands
show interface switchport
Displays the administrative and operational status of a switching (nonrouting) port.
switchport trunk native vlan
To configure trunking parameters on an interface, use the switchport trunk native vlan command. To remove the configuration, use the no form of this command.
switchport trunk native vlan id
no switchport trunk native vlan
Syntax Description
Defaults
None
Command Modes
Interface Configuration (config-if)
Port Profile Configuration (config-port-prof)Supported User Rolesnetwork-admin
Command History
Examples
This example shows how to configure trunking parameters on an interface:
n1000v# configure terminaln1000v(config)# interface vethernet 10n1000v(config-if)# switchport trunk native vlan 20n1000v(config-if)#Related Commands
system redundancy role
To configure a redundancy role for the VSM, use the system redundancy role command. To revert to the default setting, use the no form of the command.
system redundancy role {primary | secondary | standalone}
no system redundancy role {primary | secondary | standalone}
Syntax Description
primary
Specifies the primary redundant VSM.
secondary
Specifies the secondary redundant VSM.
standalone
Specifies no redundant VSM.
Command Default
None
Command Modes
EXEC
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
Examples
This example shows how to configure no redundant VSM:
n1000v# system redundancy role standalonen1000v#Related Commands
system switchover
To switch over to the standby supervisor, use the system switchover command.
system switchover
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
EXEC
Supported User Rolesnetwork-admin
Command History
Usage Guidelines
Examples
This example shows how to switch over to the standby supervisor:
n1000v# system switchovern1000v#Related Commands
