Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This section explains the objectives, intended audience, and organization of this publication and describes the conventions that convey instructions and other information.
•Added the section "Flexible Protection Mechanism" in the chapter "Transponder and Muxponder Cards".
•Updated the table "Single-Mode Fiber XFP Port Cabling Specifications" in the appendix "Hardware Specifications".
June 2010
•Updated the table "ONS 15454 Security Levels—Node View" in the chapter "Security Reference".
July 2010
•Updated the table "SFP/XFP Card Compatibility" in the chapter "Transponder and Muxponder Cards".
•Updated the section "40G-MXP-C Card Specifications" in the appendix "Hardware Specifications".
•Updated the sub-section "Key Features" under the section "40G-MXP-C Card" in the chapter "Transponder and Muxponder Cards".
•Updated the following sections:
–Updated the key features for the MXP_MR_10DME card in the chapter, Transponder and Muxponder Cards.
–Updated the section, Y-cable protection in the chapter, Transponder and Muxponder Cards.
August 2010
•Updated the table "Node View (Single-Shelf Mode) or Shelf View (Multishelf Mode) Tabs and Subtab" in the chapter, "Cisco Transport Controller Operation".
•Updated the tables "SFP Specifications" and "Single-Mode Fiber SFP Port Cabling Specifications" in the appendix "Hardware Specifications".
September 2010
•Updated the table "SFP/XFP Card Compatibility" in the chapter "Transponder and Muxponder Cards".
•Updated the "OTU2_XP Card" section in the Chapter "Transponder and Muxponder Cards".
•Added the FAPS switching criteria in the section, "Layer 2 Over DWDM Protection" in the chapter, "Transponder and Muxponder Cards".
October 2010
•Updated the "Class 1M Laser Product Statement" section in the chapters "Optical Amplifier Cards", "Multiplexer and Demultiplexer Cards", "Optical Add/Drop Cards", "Reconfigurable Optical Add/Drop Cards", and "Transponder and Muxponder Cards".
•Updated the table "Internal Patchcord Ports" in the chapter "Optical Channel Circuits and Virtual Patchcords Reference".
November 2010
•Updated the "SFP/XFP Card Compatibility" table in the "Transponder and Muxponder Cards" chapter with a new footnote.
•Updated the section, "SNMP in Multishelf Management" in the chapter, SNMP.
•Updated the width of the single slot cards for Control cards and Transponder and Muxponder Cards in the appendix, "Hardware Specifications".
•Updated the table "SFP/XFP Card Compatibility" in the chapter "Transponder and Muxponder Cards".
•Updated the tables "SFP Specifications" and "Single-Mode Fiber SFP Port Cabling Specifications" in the appendix, "Hardware Specifications".
December 2010
•Updated the table "ONS 15454 Security Levels—Node View" in the chapter "Security Reference".
January 2011
•Updated the width of all the cards in the appendix, "Hardware Specifications".
•Updated the section "40G-MXP-C Card" and the table "40G-MXP-C Card Port-Level Indicators" i nthe chapter "Transponder and Muxponder Cards".
March 2011
•Removed the table "8G Fibre Channel (FC) Payload PMs for the 40G-MXP-C Card" in the chapter, "Performance Monitoring".
April 2011
•Updated the section "Interllink Interfaces" and the table "SFP/XFP Card Compatibility" in the chapter "Transponder and Muxponder Cards".
•Updated the table, "XFP Specifications" in the chapter, "Hardware Specifications".
•Updated the section "Safety Labels" in the following chapters:
–Common Control Cards
–Optical Service Channel Cards
–Optical Amplifier Cards
–Multiplexer and Demultiplexer Cards
–Tunable Dispersion Compensating Units
–Optical Add/Drop Cards
–Reconfigurable Optical Add/Drop Cards
–Transponder and Muxponder Cards
•Updated the section "Node View (Multishelf Mode), Node View (Single-Shelf Mode), and Shelf View (Multishelf Mode)" in the chapter "Cisco Transport Controller Operation".
•Updated the section "SFP and XFP Modules" in the chapter "Transponder and Muxponder Cards".
•Updated the power values in the "Individual Card Power Requirements" table in the appendix, "Hardware Specifications".
May 2011
•Updated the section "SFP and XFP Modules" in the chapter "Transponder and Muxponder Cards".
•Removed the sections "SFP Specifications" and "XFP Specifications" and added the section "SFP and XFP Specifications" in the appendix "Hardware Specifications".
•Updated the minimum output power value for the MXP_MR_10DMEX_C card in the appendix "Hardware Specifications".
June 2011
•Updated the section "Y-Cable Protection" in the chapter "Transponder and Muxponder Cards".
•Updated the sections "MXP_2.5G_10EX_C Card Specifications" and "TXP_MR_10EX_C Card Specifications" in the chapter "Hardware Specifications".
•Updated the TNC and TSC card power consumption values in Table A-1 in the chapter "Hardware Specifications".
July 2011
•Added a note in the "PC and UNIX Workstation Requirements" section of Chapter, "Cisco Transport Controller Operation".
August 2011
•Updated the sub-section "Configuration Management" under the section "OTU2_XP Card" in the chapter "Transponder and Muxponder Cards".
•Updated the section "40G-MXP-C Card" in the chapter "Transponder and Muxponder Cards".
September 2011
•Updated the key features section of TXP_MR_10G, TXP_MR_10E, TXP_MR_10E_C, TXP_MR_10E_L, TXP_MR_10EX_C, and OTU2_XP cards in the chapter "Transponder and Muxponder Cards".
•Added a note to SONET PM Parameters table in "SONET PM Parameter Definitions" section.
•Replaced G.975.1 with G.975.1 I.7 and added a note in the "Enhanced FEC (E-FEC) Feature" section in the chapter, "Transponder and Muxponder Cards".
•Created a "Summary Pane" section in the chapter, "Cisco Transport Controller Operation".
October 2011
•Removed the Temperature table and updated the Temperature section with standard operating temperature values, removed the Environmental section from all the 15454 card specifications, and added "Environmental Exception" to "40G-MXP-C Card Specifications" section in the appendix "Hardware Specifications."
December 2011
•Updated the power values in the table "Individual Card Power Requirements" in the appendix "Hardware Specifications".
•Updated the section "Termination Modes" in the chapter "Transponder and Muxponder Cards".
January 2012
•Updated the section "GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards" with pluggable limitations in the chapter Transponder and Muxponder Cards".
February 2012
•Removed the autonegotiation support statement for ADM-10G card from the "Key Features" section in the chapter "Transponder and Muxponder Cards".
March 2012
•Updated the section, "Multishelf Node" in the chapter, " Node Reference".
April 2012
•Updated the "Functional View for an Eight-Sided Node" diagram in the chapter "Node Reference".
•Added a note in the "Displaying Optical Power" section of chapter, "Node Reference".
•Updated the "Faceplate and Block Diagram" section of "GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Cards" in the chapter, "Transponder and Muxponder Cards".
•Upadted the section "SNMP in Multishelf Management" in the chapter "SNMP".
May 2012
Updated the section "Optical Channel Circuits" in the chapter "Optical Channel Circuits and Virtual Patchcords Reference".
June 2012
Updated the section "Generic Threshold and Performance Monitoring MIBs" in the chapter "SNMP".
July 2012
Document Part Number revisioned to 78-19285-02 and a full length book-PDF was generated.
August 2012
•Updated the table "Platform and Software Release Compatibility for Control Cards" in the chapter "Common Control Cards".
•Updated the section "TCC2P Card" in the chapter "Install the Control cards" and "Supported Node Configurations for OPT-RAMP-C and OPT-RAMP-CE Cards" in the chapter "Node Reference".
•Updated the power values in the "Individual Card Power Requirements" table in the appendix, "Hardware Specifications".
October 2012
•Updated the "Circuit Provisioning" section of ADM-10G card in the chapter "Transponder and Muxponder Cards".
•Updated the section "TCC2P Card" in the chapter "Install the Control cards".
•Added a caution to the section, "IP Addressing with Secure Mode Enabled" in the chapter, "Management Network Connectivity".
December 2012
•Updated the "TCC2/TCC2P/TCC3/TNC/TSC Card Reset" section in the chapter, "Cisco Transport Controller Operation".
•Renamed chapter "Management Network Connectivity" to "Manage Network Connectivity".
February 2013
•In the chapter "Transponder and Muxponder Cards," added a note after "Table 10-44 Supported SDH Circuit Sizes of ADM-10G card on ONS 15454 SDH".
•In the chapter "Cisco Transport Controller Operation," added a new column to Table 14-1 JRE Compatibility to reflect the compatibility of releases with JRE 1.7.
April 2013
Updated the section "External Firewalls" in the chapter "Manage Network Connectivity".
May 2013
Updated the section, " REP Limitations and Restrictions" in the chapter, " Transponder and Muxponder Cards".
June 2013
Updated the section "Administrative States" in the chapter "Administrative and Service States".
October 2013
Created a new table "Revision Number Compatibility for Transponder and Muxponder Cards " in the chapter, "Transponder and Muxponder Cards".
November 2013
Updated the section "Trunk Interface" of OTU2_XP card in the chapter "Transponder and Muxponder Cards".
Document Objectives
This document provides background and reference material for Cisco ONS 15454 dense wavelength division (DWDM) systems.
Audience
To use this publication, you should be familiar with Cisco or equivalent optical transmission hardware and cabling, telecommunications hardware and cabling, electronic circuitry and wiring practices, and preferably have experience as a telecommunications technician.
Includes descriptions of the OPT-PRE, OPT-BST, OPT-BST-E, OP-BST-L, OPT-AMP-L, OPT-AMP-C, and OPT-AMP-17-C cards, as well as card temperature ranges and card compatibility.
Includes descriptions of the AD-1C-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards, card temperature ranges, compatibility, and applications.
Includes descriptions of the 32WSS, 32WSS-L, 32DMX, 32DMX-L, 40-DMX-C, 40-DMX-CE, 40-MUX-C, 40-WSS-C, 40-WSS-CE, 40-WXC-C, and MMUC cards, card temperature ranges, compatibility, and applications.
Includes information about ransponder (TXP), muxponder (MXP), GE_XP, 10GE_XP, and ADM-10G cards, as well as their associated plug-in modules (Small Form-factor Pluggables [SFPs or XFPs]).
Explains the DWDM node types t available for the ONS 15454. The DWDM node type is determined by the type of amplifier and filter cards that are installed in an ONS 15454. Also explains the DWDM automatic power control (APC), reconfigurable optical add/drop multiplexing (ROADM) power equalization, span loss verification, and automatic node setup (ANS) functions.
Explains the DWDM optical channel (OCH) circuit types and virtual patchcords that can be provisioned. Circuit types include the OCH client connection (OCHCC), the OCH trail, and the OCH network connection (OCHNC).
Provides an overview of ONS 15454 data communications network (DCN) connectivity. Cisco Optical Networking System (ONS) network communication is based on IP, including communication between Cisco Transport Controller (CTC) computers and ONS 15454 nodes, and communication among networked ONS 15454 nodes. The chapter shows common Cisco ONS 15454 IP network configurations and includes detailed data communications network (DCN) case studies.
Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for, and report performance data for early detection of problems. In this chapter, PM parameters and concepts are defined for transponder, muxponder, and dense wavelength division multiplexing (DWDM) cards in the Cisco ONS 15454 including optical amplifier, multiplexer, demutiplexer, optical add/drop multiplexer (OADM), and optical service channel (OSC) cards.
Describes the administrative and service states for Cisco ONS 15454 dense wavelength division multiplexing (DWDM) cards, optical payload ports, out-of-band optical service channel (OSC) ports, optical channel network connections (OCHNCs), and transponder/muxponder cards and ports.
Keywords or arguments that appear within square brackets are optional.
{ x | x | x }
A choice of keywords (represented by x) appears in braces separated by vertical bars. The user must select one.
Ctrl
The control key. For example, where Ctrl + D is written, hold down the Control key while pressing the D key.
screen font
Examples of information displayed on the screen.
boldface screen font
Examples of information that the user must enter.
< >
Command parameters that must be replaced by module-specific codes.
Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the document.
Caution Means reader be careful. In this situation, the user might do something that could result in equipment damage or loss of data.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.
SPARA DESSA ANVISNINGAR
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.
For safety and warning information, refer to the Cisco Optical Transport Products Safety and Compliance Information document that accompanied the product. This publication describes the international agency compliance and safety information for the Cisco ONS 15454 system. It also includes translations of the safety warnings that appear in the ONS 15454 system documentation.
Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is available in a CD-ROM package that ships with your product. The Optical Networking Product Documentation CD-ROM is updated periodically and may be more current than printed documentation.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
Feedback
The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
