Table Of Contents
Hardware Specifications
A.1 ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelf Specifications
A.2 General Card Specifications
A.2.1 Power
A.2.2 Temperature
A.3 Common Control Card Specifications
A.3.1 TCC2 Card Specifications
A.3.2 TCC2P Card Specifications
A.3.3 TCC3 Card Specifications
A.3.4 TNC Card Specifications (Cisco ONS 15454 M2 and Cisco ONS 15454 M6)
A.3.5 TSC Card Specifications (ONS 15454 M2 and ONS 15454 M6)
A.3.6 AIC-I Card Specifications
A.3.7 AEP Specifications (ANSI only)
A.3.8 MIC-A/P FMEC Specifications (ETSI only)
A.3.9 MIC-C/T/P FMEC Specifications (ETSI only)
A.3.10 MS-ISC-100T Card Specifications
A.4 Optical Service Channel Cards
A.4.1 OSCM Card Specifications
A.4.2 OSC-CSM Card Specifications
A.5 Optical Amplifier Cards
A.5.1 OPT-PRE Amplifier Card Specifications
A.5.2 OPT-BST Amplifier Card Specifications
A.5.3 OPT-BST-E Amplifier Card Specifications
A.5.4 OPT-BST-L Amplifier Card Specifications
A.5.5 OPT-AMP-L Preamplifier Card Specifications
A.5.6 OPT-AMP-17-C Amplifier Card Specifications
A.5.7 OPT-AMP-C Amplifier Card Specifications
A.5.8 OPT-RAMP-C Amplifier Card Specifications
A.5.9 OPT-RAMP-CE Amplifier Card Specifications
A.6 PSM (Protection Switching Module) Card Specifications
A.7 Multiplexer and Demultiplexer Cards
A.7.1 32MUX-O Card Specifications
A.7.2 32DMX-O Card Specifications
A.7.3 4MD-xx.x Card Specifications
A.8 Reconfigurable Optical Add/Drop Cards
A.8.1 32DMX Card Specifications
A.8.2 32DMX-L Card Specifications
A.8.3 32WSS Card Specifications
A.8.4 32WSS-L Card Specifications
A.8.5 40-MUX-C Card Specifications
A.8.6 40-DMX-C Card Specifications
A.8.7 40-DMX-CE Card Specifications
A.8.8 40-WSS-C Card Specifications
A.8.9 40-WSS-CE Card Specifications
A.8.10 40-WXC-C Card Specifications
A.8.11 80-WXC-C Card Specifications
A.8.12 40-SMR1-C Card Specifications
A.8.13 40-SMR2-C Card Specifications
A.8.14 MMU Card Specifications
A.9 Optical Add/Drop Cards
A.9.1 AD-1C-xx.x Card Specifications
A.9.2 AD-2C-xx.x Card Specifications
A.9.3 AD-4C-xx.x Card Specifications
A.9.4 AD-1B-xx.x Card Specifications
A.9.5 AD-4B-xx.x Card Specifications
A.10 Transponder and Muxponder Card Specifications
A.10.1 TXP_MR_10G Card Specifications
A.10.2 MXP_2.5G_10G Card Specifications
A.10.3 TXP_MR_2.5G and TXPP_MR_2.5G Card Specifications
A.10.4 MXP_MR_2.5G and MXPP_MR_2.5G Card Specifications
A.10.5 MXP_2.5G_10E Card Specifications
A.10.6 MXP_2.5G_10E_C Card Specifications
A.10.7 MXP_2.5G_10E_L Card Specifications
A.10.8 MXP_2.5G_10EX_C Card Specifications
A.10.9 MXP_MR_10DME_C Card Specifications
A.10.10 MXP_MR_10DME_L Card Specifications
A.10.11 MXP_MR_10DMEX_C Card Specifications
A.10.12 TXP_MR_10E Card Specifications
A.10.13 TXP_MR_10E_C Card Specifications
A.10.14 TXP_MR_10E_L Card Specifications
A.10.15 TXP_MR_10EX_C Card Specifications
A.10.16 40G-MXP-C Card Specifications
A.10.17 ADM-10G Card Specifications
A.10.18 GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Card Specifications
A.10.19 OTU2_XP Card Specifications
A.11 TDC-CC and TDC-FC Card Specifications
A.12 Mesh Patch Panel Specifications
A.12.1 PP-MESH-4 Patch Panel Specifications
A.12.2 PP-MESH-8 Patch Panel Specifications
A.12.3 15454-PP-4-SMR Patch Panel Specifications
A.13 SFP and XFP Specifications
A.14 Patch Panel Specifications
Hardware Specifications
This appendix contains hardware and software specifications for the ONS 15454 ANSI and ETSI shelf assemblies and cards.
Note 
Unless otherwise specified, "ONS 15454" refers to both ANSI and ETSI shelf assemblies.
The following sections are included:
•ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelf Specifications
•General Card Specifications
•Common Control Card Specifications
•Optical Service Channel Cards
•Optical Amplifier Cards
•PSM (Protection Switching Module) Card Specifications
•Multiplexer and Demultiplexer Cards
•Reconfigurable Optical Add/Drop Cards
•Optical Add/Drop Cards
•Transponder and Muxponder Card Specifications
•TDC-CC and TDC-FC Card Specifications
•Mesh Patch Panel Specifications
•SFP and XFP Specifications
•Patch Panel Specifications
A.1 ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelf Specifications
For information on shelf bandwidth; list of topologies; Cisco Transport Controller (CTC) specifications; the LAN, Transaction Language One (TL1), modem, and alarm specifications; timing, power, and environmental specifications; and shelf dimensions, refer to Appendix A, Hardware Specifications" in the "Cisco ONS 15454 Hardware Installation Guide".
A.2 General Card Specifications
This section provides power specifications and temperature ranges for all ONS 15454 cards.
A.2.1 Power
Table A-1 provides power consumption information for the ONS 15454 cards.
Table A-1 Individual Card Power Requirements
Card Type
|
Card Name
|
Maximum Power in Watts
|
Typical Power in Watts
|
Amperes at -48 V
|
BTU/Hr.
|
Common Control Cards
|
TCC2/TCC2P/TCC3
|
30
|
19.2
|
0.54
|
89
|
TNC
|
62
|
52
|
0.94
|
153
|
TSC
|
55
|
46
|
0.79
|
129
|
AIC-I
|
10
|
6
|
0.17
|
28
|
AEP
|
-
|
-
|
(from +5 VDC from AIC-I)
|
10
|
MIC-A/P
|
0.2
|
0.13
|
via TCC2/TCC2P/TCC3
|
0.44
|
MIC-C/T/P
|
0.5
|
0.38
|
via TCC2/TCC2P/TCC3
|
1.29
|
MS-ISC-100T
|
69
|
53
|
1.10
|
181.0
|
Optical Service Channel Cards
|
OSCM
|
26
|
23
|
0.48
|
79
|
OSC-CSM
|
27
|
24
|
0.5
|
82
|
Optical Amplifier Cards
|
OPT-PRE
|
39
|
30
|
0.63
|
103
|
OPT-BST
|
39
|
30
|
0.63
|
103
|
OPT-BST-E
|
39
|
30
|
0.63
|
103
|
OPT-BST-L
|
32
|
25
|
0.52
|
86
|
OPT-AMP-L
|
40
|
32
|
0.67
|
110
|
OPT-AMP-17-C
|
23
|
19
|
0.83
|
137
|
OPT-AMP-C
|
30
|
23
|
0.83
|
137
|
OPT-RAMP-C
|
55
|
44
|
1.04
|
171
|
OPT-RAMP-CE
|
58
|
46
|
0.83
|
137
|
PSM Card
|
PSM
|
50
|
35
|
0.41
|
69
|
Multiplexer and Demultiplexer Cards
|
32MUX-O
|
25
|
16
|
0.33
|
55
|
32DMX-O
|
25
|
16
|
0.33
|
55
|
4MD-xx.x
|
25
|
17
|
0.35
|
58.0
|
ROADM Cards
|
32DMX
|
25
|
15
|
0.31
|
52
|
32DMX-L
|
25
|
15
|
0.31
|
52
|
32WSS
|
65
|
50
|
1.04
|
171
|
32WSS-L
|
48
|
43
|
0.90
|
147
|
40-MUX-C
|
39
|
35
|
0.73
|
120
|
40-DMX-C
|
39
|
35
|
0.73
|
120
|
40-DMX-CE
|
39
|
35
|
0.73
|
120
|
40-WSS-C
|
79
|
63
|
1.53
|
250
|
40-WSS-CE
|
79
|
63
|
1.53
|
250
|
40-WXC-C
|
33
|
30
|
0.63
|
103
|
80-WXC-C
|
40
|
20
|
0.42
|
69
|
40-SMR1-C
|
60
|
30
|
0.73
|
120
|
40-SMR2-C
|
70
|
35
|
0.83
|
137
|
MMU
|
15
|
7
|
0.15
|
24
|
Optical Add/Drop Cards
|
AD-1C-xx.x
|
25
|
17
|
0.35
|
58.0
|
AD-2C-xx.x
|
25
|
17
|
0.35
|
58.0
|
AD-4C-xx.x
|
25
|
17
|
0.35
|
58.0
|
AD-1B-xx.x
|
25
|
17
|
0.35
|
58.0
|
AD-4B-xx.x
|
25
|
17
|
0.35
|
58.0
|
Transponder and Muxponder Cards
|
TXP_MR_10G
|
50
|
32.5
|
0.73
|
120
|
TXP_MR_10E
|
50
|
32.5
|
1.05
|
171
|
TXP_MR_10E_C
|
50
|
31.8
|
1.05
|
171
|
TXP_MR_10E_L
|
50
|
31.8
|
1.05
|
171
|
TXP_MR_10EX_C
|
53
|
34.4
|
0.88
|
144
|
TXP_MR_2.5G
|
31
|
24.3
|
0.73
|
120
|
TXPP_MR_2.5G
|
31
|
24.3
|
1.05
|
171
|
MXP_2.5G_10G
|
60
|
43.6
|
1.05
|
171
|
MXP_2.5G_10E
|
60
|
43.6
|
1.05
|
171
|
MXP_2.5G_10E_C
|
60
|
43.6
|
1.05
|
171
|
MXP_2.5G_10E_L
|
60
|
43.6
|
1.05
|
171
|
MXP_2.5G_10EX_C
|
60
|
43.6
|
1.05
|
171
|
MXP_MR_2.5G
|
60
|
43.6
|
1.05
|
171
|
MXPP_MR_2.5G
|
60
|
43.6
|
1.05
|
171
|
Transponder and Muxponder Cards
|
MXP_MR_10DME_C
|
71
|
53.4
|
1.25
|
205
|
MXP_MR_10DME_L
|
71
|
53.4
|
1.25
|
205
|
MXP_MR_10DMEX_C
|
74
|
56
|
1.25
|
205
|
40G-MXP-C
|
112
|
90
|
2.34
|
383
|
ADM-10G
|
160
|
135
|
2.81
|
461
|
OTU2_XP
|
70
|
50.8
|
1.48
|
243
|
TDCU Cards
|
TDC-CC
|
12
|
11
|
0.17
|
28
|
TDC-FC
|
12
|
11
|
0.17
|
28
|
A.2.2 Temperature
•Operating temperature:
–Long term: 0 to 40 degrees Celsius (32 to 104 degrees Fahrenheit)
–Short term: Functionality is guaranteed at -5 to 55 degrees Celsius (23 to 131 degrees Fahrenheit), according to GR-63 Issue 3
The indicated temperatures are the ambient ones in which the shelf can be placed.
A.3 Common Control Card Specifications
This section provides specifications for the TCC2, TCC2P, TCC3, TNC, TSC, AIC, and AIC-I cards, the alarm expansion panel (AEP), the MIC-A/P and MIC-C/T/P FMECs, and the MS-ISC-100T card.
For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance Information document.
A.3.1 TCC2 Card Specifications
The TCC2 card has the following specifications:
•CTC software
–Interface: EIA/TIA-232 (local craft access, on TCC2 faceplate)
–Interface: 10BaseT LAN (on TCC2 faceplate)
–Interface: 10BaseT LAN (through the backplane)
•Synchronization
–Stratum 3, per Telcordia GR-253-CORE
–Free running access: Accuracy +/- 4.6 ppm
–Holdover stability: 3.7 x 10-7 per day including temperature (< 255 slips in first 24 hours)
–Reference: External BITS, line, internal
•Supply voltage monitoring
–Both supply voltage inputs are monitored.
–Normal operation: -40.5 to -56.7 V
–Undervoltage: Major alarm
–Overvoltage: Major alarm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 235 mm (9.250 in.)
–Weight not including clam shell: 0.7 kg (1.5 lb)
A.3.2 TCC2P Card Specifications
The TCC2P card has the following specifications:
•CTC software
–Interface: EIA/TIA-232 (local craft access, on TCC2P faceplate)
–Interface: 10BaseT LAN (on TCC2P faceplate)
–Interface: 10BaseT LAN (through the backplane)
•Synchronization
–Stratum 3, per Telcordia GR-253-CORE
–Free running access: Accuracy +/- 4.6 ppm
–Holdover stability: 3.7 * 10 exp - 7 per day including temperature (< 255 slips in first 24 hours)
–Reference: External BITS, line, internal
•Supply voltage monitoring
–Both supply voltage inputs are monitored.
–Normal operation: -40.5 to -56.7 V (in -48 VDC systems)
–Undervoltage: Major alarm
–Overvoltage: Major alarm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 1.5 lb (0.7 kg)
A.3.3 TCC3 Card Specifications
The TCC3 card has the following specifications:
•CTC software
–Interface: EIA/TIA-232 (local craft access, on TCC3 faceplate)
–Interface: 10BaseT LAN (on TCC3 faceplate)
–Interface: 10BaseT LAN (through the backplane)
•Synchronization
–Stratum 3, per Telcordia GR-253-CORE
–Free running access: Accuracy +/- 4.6 ppm
–Holdover stability: 3.7 * 10 exp - 7 per day including temperature (< 255 slips in first 24 hours)
–Reference: External BITS, line, internal
•Supply voltage monitoring
–Both supply voltage inputs are monitored.
–Normal operation: -40.5 to -56.7 V (in -48 VDC systems)
–Undervoltage: Major alarm
–Overvoltage: Major alarm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 1.5 lb (0.7 kg)
A.3.4 TNC Card Specifications (Cisco ONS 15454 M2 and Cisco ONS 15454 M6)
The TNC card has the following specifications:
•CTC software
–Interface: EIA/TIA-232 (local craft access, on TNC faceplate)
–Interface: 10BaseT LAN (on TNC faceplate)
–Interface: 10BaseT LAN (through the external connection unit for EMS, CT, MSM, VoIP, UDC and Line Cards)
–Two SFP interfaces to support Optical Service Channels (OC-3/STM-1 or FE/GE)
•Synchronization
–Stratum 3, per Telcordia GR-253-CORE
–Free running access: Accuracy +/- 4.6 ppm
–Holdover stability: 3.7 * 10 exp - 7 per day including temperature (< 255 slips in first 24 hours)
–Reference: External BITS, line, internal
•Supply voltage monitoring
–Both the input supply voltages are monitored.
–Normal operation: -40.5 to -56.7 V (in -48 VDC systems)
–AC input voltage range: Undervoltage TH 90V histeresis 5V; Overvoltage TH 254V histeresis 10V
–Undervoltage: Major alarm
–Overvoltage: Major alarm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 1.6 lb (0.8 kg)
A.3.5 TSC Card Specifications (ONS 15454 M2 and ONS 15454 M6)
The TSC card has the following specifications:
•CTC software
–Interface: EIA/TIA-232 (local craft access, on TSC faceplate)
–Interface: 10BaseT LAN (on TSC faceplate)
–Interface: 10BaseT LAN (through the external connection unit for EMS, CT, MSM, VoIP, UDC and Line Cards)
•Synchronization
–Stratum 3, per Telcordia GR-253-CORE
–Free running access: Accuracy +/- 4.6 ppm
–Holdover stability: 3.7 * 10 exp - 7 per day including temperature (< 255 slips in first 24 hours)
–Reference: External BITS, line, internal
•Supply voltage monitoring
–Both the input supply voltages are monitored.
–Normal operation: -40.5 to -56.7 V (in -48 VDC systems)
–AC input voltage range: Undervoltage TH 90V histeresis 5V; Overvoltage TH 254V histeresis 10V
–Undervoltage: Major alarm
–Overvoltage: Major alarm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 1.6 lb (0.8 kg)
A.3.6 AIC-I Card Specifications
The AIC-I card has the following specifications:
•Alarm inputs
–Number of inputs: 12 without AEP, 32 with AEP
–Opto-coupler isolated
–Label customer provisionable
–Severity customer provisionable
–Common 32 V output for all alarm inputs
–Each input limited to 2 mA
–Termination: Wire-wrap on backplane without AEP, on AEP connectors with AEP
•Alarm outputs
–Number of outputs: 4 (user configurable as inputs) without AEP, 16 with AEP
–Switched by opto MOS (metal oxide semiconductor)
–Triggered by definable alarm condition
–Maximum allowed open circuit voltage: 60 VDC
–Maximum allowed closed circuit current: 100 mA
–Termination: Wire-wrap on backplane without AEP, on AEP connectors with AEP
•Express orderwire/local orderwire (EOW/LOW)
–ITU-T G.711, ITU-T G.712, Telcordia GR-253-CORE
–A-law, mu-law
Note Due to the nature of mixed coding, in a mixed-mode (A-law/mu-law) configuration, the orderwire is not ITU-T G.712 compliant.
–Orderwire party line
–Dual tone, multifrequency (DTMF) signaling
•User data channel (UDC)
–Bit rate: 64 kbps, codirectional
–ITU-T G.703
–Input/output impedance: 120 ohm
–Termination: RJ-11 connectors
•Data communications channel (DCC)
–Bit rate: 576 kbps
–EIA/TIA-485/V11
–Input/output impedance: 120 ohm
–Termination: RJ-45 connectors
•ACC connection for additional alarm interfaces
–Connection to AEP
•Power monitoring alarming states:
–Power failure (0 to -38 VDC)
–Undervoltage (-38 to -40.5 VDC)
–Overvoltage (beyond -56.7 VDC)
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Weight: 1.8 lb (0.82 kg)
A.3.7 AEP Specifications (ANSI only)
The AEP has the following specifications:
•Alarm inputs
–Number of inputs: 32
–Optocoupler isolated
–Label customer provisionable
–Severity customer provisionable
–Common 32 V output for all alarm inputs
–Each input limited to 2 mA
–Termination: 50-pin AMP champ connector
•Alarm outputs
–Number of outputs: 16
–Switched by opto MOS
–Triggered by definable alarm condition
–Maximum allowed open circuit voltage: 60 VDC
–Maximum allowed closed circuit current: 100 mA
–Termination: 50-pin AMP champ connector
•Environmental
–Overvoltage protection: as in ITU-T G.703 Annex B
•Dimensions of AEP board
–Height: 20 mm (0.79 in.)
–Width: 330 mm (13.0 in.)
–Depth: 89 mm (3.5 in.)
–Weight: 0.18 kg (0.4 lb)
A.3.8 MIC-A/P FMEC Specifications (ETSI only)
The MIC-A/P FMEC card has the following specifications:
•Power supply input BATTERY B
–System supply voltage: Nominal -48 VDC
Tolerance limits: -40.5 to -57.0 VDC
–Connector: 3WK3 Combo-D power cable connector
•Alarm outputs
–Voltage (open contact): Maximum 60 VDC
–Current (closed contact): Maximum 250 mA
–Connector: 62-pin DB connector (common for inputs/outputs)
•Alarm inputs
–Voltage (open contact): Maximum 60 VDC
–Current (closed contact): Maximum 2 mA
–Connector: 62-pin DB connector (common for inputs/outputs)
•Dimensions
–Height: 182 mm (7.165 in.)
–Width: 31.88 mm (1.255 in.)
–Depth: 92 mm (3.62 in.)
–Depth with backplane connector: 98 mm (3.87 in.)
–Weight not including clam shell: 0.2 kg (0.5 lb)
A.3.9 MIC-C/T/P FMEC Specifications (ETSI only)
The MIC-C/T/P FMEC card has the following specifications:
•Power supply input BATTERY A
–System supply voltage: Nominal -48 VDC
Tolerance limits: -40.5 to -57.0 VDC
–Connector: 3WK3 Combo-D power cable connector
•Timing connector
–Frequency: 2.048 MHz +/-10 ppm
–Signal level: 0.75 to 1.5 V
–Impedance: 75 ohms +/-5 percent (switchable by jumper to high impedance > 3 kohms)
Note 120 ohms balanced impedance is possible with external matching cable.
–Cable attenuation: Up to 6 dB at 2 MHz
–Connectors: 1.0/2.3 miniature coax connector
•System management serial port:
–System management serial port craft interface
–Modem port (for future use)
–Connectors: 8-pin RJ-45
•System management LAN port connectors:
–Signal: IEEE 802.3 10BaseT
–Connectors: 8-pin RJ-45
•Dimensions
–Height: 182 mm (7.165 in.)
–Width: 31.88 mm (1.255 in.)
–Depth: 92 mm (3.62 in.)
–Depth with backplane connector: 98 mm (3.87 in.)
–Weight not including clam shell: 0.2 kg (0.5 lb)
A.3.10 MS-ISC-100T Card Specifications
The MS-ISC-100T card has the following specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 2.3 lb (1.0 kg)
A.4 Optical Service Channel Cards
This section provides specifications for the OSCM and OSC-CSM cards.
A.4.1 OSCM Card Specifications
The OSCM card has the following specifications:
•Line
–Bit rate: 155 Mbps
–Code: Scrambled non-return to zero (NRZ)
–Loopback modes: None
–Connector: Duplex LC
•Transmitter optical service channel (OSC) signal
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -5 dBm
–Nominal wavelength: 1510-nm +/-10 nm
–Variable optical attenuator (VOA) necessary in the transmit path to adjust the in-fiber optical power level
•Receiver OSC signal
–Maximum receiver level: -8 dBm at 10-10 bit error rate (BER)
–Minimum receiver level: -40 dBm at 10-10 BER
–Span budget: 40-dB span budget (about 150 km assuming fiber path loss equals 0.25 dB/km)
–Jitter tolerance: Telcordia GR-253/G.823 compliant
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.4.2 OSC-CSM Card Specifications
The OSC-CSM card has the following specifications:
•Line
–Bit rate: 155 Mbps
–Code: Scrambled NRZ
–Loopback modes: None
–Connector: Duplex LC
•Transmitter OSC signal
–Maximum transmitter output power: -2 dBm
–Minimum transmitter output power: -24 dBm
–Nominal wavelength: 1510-nm +/-10 nm
–VOA is necessary in the transmit path to adjust the in-fiber optical power level
•Receiver OSC signal
–Maximum receiver level: -8 dBm at 10-10 BER
–Minimum receiver level: -40 dBm at 10-10 BER
–Span loss budget: 35-dB span budget (approximately 140 km assuming that the fiber path loss is equal to 0.25 dB/km)
–Jitter tolerance: Telcordia GR-253/G.823 compliant
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.5 Optical Amplifier Cards
This section provides specifications for the OPT-PRE amplifier, OPT-BST amplifier, OPT-BST-E amplifier, OPT-BST-L amplifier, OPT-AMP-L preamplifier (configurable as a preamplifier or booster amplifier), OPT-AMP-C amplifier (configurable as a preamplifier or booster amplifier), OPT-AMP-17-C, and OPT-RAMP-C amplifier cards.
A.5.1 OPT-PRE Amplifier Card Specifications
The OPT-PRE amplifier card has the following specifications:
•Optical characteristics:
–Total operating wavelength range: 1530 to 1561.3 nm
–Gain ripple (peak to valley): 1.5 dB
–Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 3 to 9 dB
–Gain range: 5 to 38.5 dBm in constant power mode, 5 to 28 dBm in constant gain mode
–Minimum gain (standard range): 5.0 dBm
– Maximum gain (standard range with programmable gain tilt): 21 dBm
– Maximum gain (extended range with uncontrolled gain tilt): 38.5 dBm
–Gain and power regulation over/undershoot: 0.5 dB
–Limited maximum output power: 17.5 dBm
–Maximum output power (with full channel load): 17 dB
–Minimum output power (with one channel): -2 dBm
–Input power (Pin) range at full channel load: -21.5 to 12 dBm
–Input power (Pin) range at single channel load: -39.5 to -6 dBm
–Noise figure at G3 21 dB = 6.5 dB
–OSC filter drop (channels) insertion loss maximum: 1 dB
–OSC filter drop (OSC) insertion loss maximum: 1.8 dB
–OSC filter add (OSC) insertion loss maximum: 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.2 OPT-BST Amplifier Card Specifications
The OPT-BST amplifier card has the following specifications:
•Optical characteristics:
–Total operating wavelength range: 1530 to 1561.3 nm
–Gain ripple (peak to valley): 1.5 dB
–Gain range: 5 to 20 dBm with programmable gain tilt
–Gain and power regulation over/undershoot: 0.5 dB
–Limited maximum output power: 17.5 dBm
–Maximum output power (with full channel load): 17 dB
–Minimum output power (with one channel): -2 dBm
–Input power (Pin) range at full channel load: -3 to 12 dBm
–Input power (Pin) range at single channel load: -21 to -6 dBm
–Noise figure at G3 20 dB = 6 dB
–OSC filter drop (channels) insertion loss maximum: 1 dB
–OSC filter drop (OSC) insertion loss maximum: 1.8 dB
–OSC filter add (OSC) insertion loss maximum: 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.3 OPT-BST-E Amplifier Card Specifications
The OPT-BST-E amplifier card has the following specifications:
•Optical characteristics:
–Total operating wavelength range: 1530 to 1561.3 nm
–Gain ripple (peak to valley): 1.8 dB
–Gain range: 8 to 23 dB with programmable gain tilt
–Extended gain range: 23 to 26 dB with gain tilt uncontrolled
–Gain and power regulation over/undershoot: 0.5 dB
–Limited maximum output power: 20.5 dBm
–Maximum output power (with full channel load): 20 dB
–Minimum output power (with one channel): -0 dBm
–Input power (Pin) range at full channel load: -6 to 12 dBm
–Input power (Pin) range at single channel load: -26 to -8 dBm
–Noise figure at G3 23 dB = 6 dB
–OSC filter drop (channels) insertion loss maximum: 1 dB
–OSC filter drop (OSC) insertion loss maximum: 1.8 dB
–OSC filter add (OSC) insertion loss maximum: 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.4 OPT-BST-L Amplifier Card Specifications
The OPT-BST-L amplifier card has the following specifications:
•Optical characteristics:
–Total operating wavelength range: 1570.0 to 1605.0 nm
–Gain ripple (peak to valley): 1.5 dB
–Gain range: 8 to 20 dB with programmable gain tilt
–Extended gain range: 20 to 27 dB with gain tilt uncontrolled
–Gain and power regulation over/undershoot: 0.5 dB
–Limited maximum output power: 10 dBm
–Maximum output power (with full channel load): 17 dB
–Minimum output power (with one channel): -1 dBm
–Input power (Pin) range at full channel load: -10 to 9 dBm
–Input power (Pin) range at single channel load: -37 to -18 dBm
–Noise figure at G3 20 dB = 7.5 dB
–Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
–Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
–Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.5 OPT-AMP-L Preamplifier Card Specifications
The OPT-AMP-L card has the following specifications:
•Optical characteristics:
–DWDM channel wavelength plan, 100 GHz, 4 skip 1, ITU-T wavelength grid channels 71 (1602.3 nm) to 90 (1570.4 nm)
–DWDM channel wavelength plan, 50 GHz, 8 skip 2, ITU-T wavelength grid channels 70.5 (1602.7 nm) to 90 (1570.4 nm)
–Channel spacing: 100 and 50 GHz
–Total operating wavelength range 1570.0 - 1605.0 nm
–Gain ripple (peak to valley): 1.5 dB
–Standard gain range: 12 to 24 dB
–Extended gain range (uncontrolled gain tilt): 24 to 35 dB
–Gain and power regulation over/undershoot: 0.5 dB
–Minimum output power (with one channel): +2 dBm
–Maximum power output (standard or extended gain range): 20 dB
–Input power range (full channel load): -15 to 8 dB
–Input power range (single channel load): -40 to -17
–Noise figure at G3 20 dB = 8.9 dB
–Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
–Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
–Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (240 mm)
A.5.6 OPT-AMP-17-C Amplifier Card Specifications
The OPT-AMP-17-C card has the following specifications:
•Optical characteristics:
–DWDM channel wavelength plan: 80 channels at 50 GHz spacing, 1530.33 nm to 1561.83 nm
–Channel spacing: 50 GHz
–Total operating wavelength range 1529.0 to 1562.5 nm
–Gain ripple (peak to valley): 1.5 dB
–Gain range: 14 to 23 dB
–Optimal gain (gain tilt = 0): 17 dB
–Gain and power regulation over/undershoot: 0.5 dB
–Minimum output power (with one channel): -2 dBm
–Maximum power output (standard or extended gain range): 17.5 dBm
–Input power range (full channel load): -6 to 3 dBm
–Input power range (single channel load): -28 to -19 dBm
–Noise figure at G=17dB = 6 dB maximum
–Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
–Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
–Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.5.7 OPT-AMP-C Amplifier Card Specifications
The OPT-AMP-C amplifier card has the following specifications:
•Optical characteristics:
–Total operating wavelength range: 1529.0 to 1562.5 nm
–Gain ripple (peak to valley): 1.2 dB
–Gain range: 12 to 24 dB with programmable gain tilt
–Extended gain range: 24 to 35 dB with gain tilt uncontrolled
–Gain and power regulation over/undershoot: 0.5 dB
–Limited maximum output power: 20.5 dBm
–Maximum output power (with full channel load): 20 dBm
–Minimum output power (with one channel): -2 dBm
–Input power (Pin) at full channel load: -15 dBm minimum
–Input power (Pin) range at single channel load: -40 to -17 dBm
–Noise figure at G3 20 dB: 7.6 dB
–Insertion loss (Line RX to OSC TX): 0.3 to 1.8 dB
–Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
–Insertion loss (OSC RX to LINE TX): 0.3 to 1.3 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 8.66 in. (220.1 mm)
A.5.8 OPT-RAMP-C Amplifier Card Specifications
The OPT-RAMP-C amplifier card has the following specifications:
•Raman pump
–Raman pump 1 wavelength: 1425 nm
–Raman pump 2 wavelength: 1452 nm
–Total Raman Pump power - Line-RX port: 500 mW
–Operating range Raman Pump power - Line-RX port: min 100 mW, max 4502 mW
–Raman pump laser class: 3B
•Embedded EDFA
–Total operating signal wavelength range: 1529 to 1562.5 nm
–EDFA nominal gain value (Line RX to DC-TX): 14 dB
–EDFA gain settable range: 8 to 20 dB
–EDFA Output Power range - DC-TX (Full Channel load): 17.53 dBm
–VOA attenuation range: 0 to 25 dB
–Gain and power regulation over/undershoot: 0.5 dB
–EDFA laser class: 1M
–Maximum EDFA output power: 17.5 dBm
–Minimum output power (with one channel): -10 dBm
–Input power (Pin) at full channel load: -3 dBm to +9 dBm
–Input power (Pin) range at single channel load: -24dBm to -10 dBm
–Noise figure at G 14 dB: 7.5 dB
–Insertion loss (Line TX to OSC TX): 0.3 to 2.0 dB
–Insertion loss (Line RX to COM TX): 0.3 to 1.0 dB
–Insertion loss (OSC RX to LINE RX): 0.3 to 1.8 dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 8.665 in. (220.1 mm)
A.5.9 OPT-RAMP-CE Amplifier Card Specifications
The OPT-RAMP-CE amplifier card has the following specifications:
•Raman pump
–Raman pump 1 wavelength: 1425 nm
–Raman pump 2 wavelength: 1452 nm
–Total Raman pump power - LINE-RX port: 500 mW
–Operating range Raman pump power - LINE-RX port: min 100 mW, max 450 mW
–Raman pump laser class: 3B
•Embedded EDFA
–Total operating signal wavelength range: 1529 to 1562.5 nm
–EDFA nominal gain value (LINE-RX to DC-TX): 11 dB
–EDFA gain settable range: 5 to 17 dB
–EDFA Output power range - DC-TX (Full Channel load): 20.2 dBm
–VOA attenuation range: 0 to 25 dB
–Gain and power regulation over/undershoot: 0.5 dB
–EDFA laser class: 1M
–Maximum EDFA output power: 20.5 dBm
–Minimum output power (with one channel): -10 dBm
–Input power (Pin) at full channel load: 15 dBm (maximum)
–Input power (Pin) range at single channel load: -27dBm (minimum)
–Noise figure at G 11 dB: 7 dB
–Insertion loss (LINE-RX to MON-RX):22 to 26 dB
–Insertion loss (LINE-TX to OSC-TX): 1.5 dB
–Insertion loss (OSC-RX to LINE-RX): 0.7 to 1.7 dB
–Insertion loss (LINE-TX to COM-RX): 0.6 to 1.0 dB
–Insertion loss (LINE-TX to PD12): 1.7dB
–Insertion loss (OSC-RX to LINE-RX): 0.7 to 1.7dB
–Optical connectors: LC-UPC/2
•Dimensions
–Height: 13.11 in. (333 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.88 in. (251 mm)
A.6 PSM (Protection Switching Module) Card Specifications
The PSM card has the following specifications:
•Wavelength:
–Total operating signal wavelength range (C-band range): 1529.0 - 1562.5 nm
–OSC wavelength range: 1500 - 1520 nm
–L-band range: 1570 - 1605 nm
•Optical
–Insertion loss:
•COM-RX to W-TX and P-TX: 4.6 dB
•W-RX and P-RX to COM-TX: 2.3 dB
–Insertion loss ripple: 0.2 dB
–Maximum optical input power: 300mW
–Polarization dependent loss: 0.2 dB
–Optical switches state setting time: 5 ms
–VOA attenuation setting time in open loop: 20 ms
–VOA attenuation setting time in closed loop: 500 ms (applicable to VOA in RX only)
–VOA attenuation range: 0 - 15 dB
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 8.66 in. (220.1 mm)
A.7 Multiplexer and Demultiplexer Cards
This section provides specifications for the 32MUX-O, 32DMX-O, and 4MD-xx.x cards.
A.7.1 32MUX-O Card Specifications
The 32MUX-O card optical specifications are listed in Table A-2.
Note For power specifications, see Table A-1.
Table A-2 32MUX-O Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Transmit (Tx) filter shape (-1 dB bandwidth)
|
All standard operating procedures (SOP) and within whole operating temperature range
|
In 1/32—Out beginning of life (BOL)
|
+/-180
|
+/-300
|
pm
|
In 1/32—Out end of life (EOL)
|
+/-160
|
+/-300
|
pm
|
Insertion loss
|
All SOP and within whole operating temperature range
|
In 1/32—Out BOL
|
4
|
8.0
|
dB
|
In 1/32—Out EOL
|
4
|
8.5
|
dB
|
VOA dynamic range
|
—
|
—
|
25
|
—
|
dB
|
Optical monitor tap-splitting ratio on monitor port
|
Optical monitor port with respect to output port in multiplexer only
|
—
|
19
|
21
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The 32MUX-O card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.7.2 32DMX-O Card Specifications
The 32DMX-O card optical specifications are listed in Table A-3.
Note For power specifications, see Table A-1.
Table A-3 32DMX-O Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Receive (Rx) filter shape (-1 dB bandwidth)
|
All SOP and within whole operating temperature range
|
In 1/32—Out BOL
|
+/-180
|
+/-300
|
pm
|
In 1/32—Out EOL
|
+/-160
|
+/-300
|
pm
|
Insertion loss
|
All SOP and within whole operating temperature range
|
In 1/32—Out BOL
|
4
|
8.0
|
dB
|
In 1/32—Out EOL
|
4
|
8.5
|
dB
|
VOA dynamic range
|
—
|
—
|
25
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The 32DMX-O card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.7.3 4MD-xx.x Card Specifications
The 4MD-xx.x card optical specifications are listed in Table A-4.
Note For power specifications, see Table A-1.
Table A-4 4MD-xx.x Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Trx filter shape (-0.5 dB bandwidth TrxBW2)
|
All SOP and within whole operating temperature range
|
COM Rx—xx.xx Tx
COM Rx—yy.yy Tx
COM Rx—zz.zz Tx
COM Rx—kk.kk Tx
|
+/-180
|
—
|
pm
|
xx.xx Rx—COM Tx
yy.yy Rx—COM Tx
zz.zz Rx—COM Tx
kk.kk Rx—COM Tx
|
Insertion loss demultiplexer section
|
All SOP and within whole operating temperature range
|
COM Rx—xx.xx Tx
|
—
|
1.9
|
dB
|
COM Rx—yy.yy Tx
|
—
|
2.4
|
dB
|
COM Rx—zz.zz Tx
|
—
|
2.8
|
dB
|
COM Rx—kk.kk Tx
|
—
|
3.3
|
dB
|
Insertion loss multiplexer section
|
All SOP and within whole operating temperature range (two connectors included)
|
xx.xx Rx—COM Tx
|
—
|
3.6
|
dB
|
yy.yy Rx—COM Tx
|
—
|
3.2
|
dB
|
zz.zz Rx—COM Tx
|
—
|
3.0
|
dB
|
kk.kk Rx—COM Tx
|
—
|
2.6
|
dB
|
VOA dynamic range
|
—
|
—
|
25
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The 4MD-xx.x card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.8 Reconfigurable Optical Add/Drop Cards
This section provides specifications for the 32DMX, 32DMX-L, 32WSS, 32WSS-L, 40-MUX-C, 40-DMX-C, 40-DMX-CE, 40-WSS-C, 40-WSS-CE, 40-WXC-C, 80-WXC-C, 40-SMR1-C, 40-SMR2-C, and MMU cards.
A.8.1 32DMX Card Specifications
The 32DMX card optical specifications are listed in Table A-5.
Note For power specifications, see Table A-1.
Table A-5 32DMX Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Typical
|
Max
|
Units
|
-1 dB bandwidth
|
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation.
|
COM RX => TX 1, 32 (OUT)
|
+/-110
|
—
|
—
|
pm
|
-3 dB bandwidth
|
+/-200
|
—
|
—
|
pm
|
Insertion loss
|
All SOP, and within whole operating temperature range, connectors included.
|
COM RX => TX 1, 32
|
—
|
—
|
5.5
|
dB
|
VOA dynamic range
|
—
|
COM RX => TX 1, 32
|
25
|
—
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
—
|
mW
|
The 32DMX channel plan is shown in Table A-6. All 32DMX client interfaces must comply with this plan.
Table A-6 32DMX Channel Plan
Channel Number
|
Band
|
Channel ID
|
Frequency (GHz)
|
Wavelength (nm)
|
1
|
1
|
30.3
|
195.9
|
1530.33
|
2
|
31.2
|
195.8
|
1531.12
|
3
|
31.9
|
195.7
|
1531.90
|
4
|
32.6
|
195.6
|
1532.68
|
5
|
2
|
34.2
|
195.4
|
1534.25
|
6
|
35.0
|
195.3
|
1535.04
|
7
|
35.8
|
195.2
|
1535.82
|
8
|
36.6
|
195.1
|
1536.61
|
9
|
3
|
38.1
|
194.9
|
1538.19
|
10
|
38.9
|
194.8
|
1538.98
|
11
|
39.7
|
194.7
|
1539.77
|
12
|
40.5
|
194.6
|
1540.56
|
13
|
4
|
42.1
|
194.4
|
1542.14
|
14
|
42.9
|
194.3
|
1542.94
|
15
|
43.7
|
194.2
|
1543.73
|
16
|
44.5
|
194.1
|
1544.53
|
17
|
5
|
46.1
|
193.9
|
1546.12
|
18
|
46.9
|
193.8
|
1546.92
|
19
|
47.7
|
193.7
|
1547.72
|
20
|
48.5
|
193.6
|
1548.51
|
21
|
6
|
50.1
|
193.4
|
1550.12
|
22
|
50.9
|
193.3
|
1550.92
|
23
|
51.7
|
193.2
|
1551.72
|
24
|
52.5
|
193.1
|
1552.52
|
25
|
7
|
54.1
|
192.9
|
1554.13
|
26
|
54.9
|
192.8
|
1554.94
|
27
|
55.7
|
192.7
|
1555.75
|
28
|
56.5
|
192.6
|
1556.55
|
29
|
8
|
58.1
|
192.4
|
1558.17
|
30
|
58.9
|
192.3
|
1558.98
|
31
|
59.7
|
192.2
|
1559.79
|
32
|
60.6
|
192.1
|
1560.61
|
The 32DMX card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.8.2 32DMX-L Card Specifications
The 32DMX-L card optical specifications are listed in Table A-5.
Note For power specifications, see Table A-1.
Table A-7 32DMX -L Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Typical
|
Max
|
Units
|
-1 dB bandwidth
|
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation.
|
COM RX => TX 1, 32 (OUT)
|
+/-100
|
—
|
—
|
pm
|
-3 dB bandwidth
|
+/-199
|
—
|
—
|
pm
|
Insertion loss
|
All SOP, and within whole operating temperature range, connectors included.
|
COM RX => TX 1, 32
|
—
|
—
|
5.8
|
dB
|
VOA dynamic range
|
—
|
COM RX => TX 1, 32
|
25
|
—
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
—
|
mW
|
The 32DMX-L channel plan is shown in Table A-8. All 32DMX-L client interfaces must comply with this plan.
Table A-8 32DMX-L Channel Plan
Band ID
|
Channel Label
|
Frequency (THz)
|
Wavelength (nm)
|
B77.8
|
77.8
|
190
|
1577.86
|
78.6
|
189.9
|
1578.69
|
79.5
|
189.8
|
1579.52
|
80.3
|
189.7
|
1580.35
|
B81.1
|
81.1
|
189.6
|
1581.18
|
82.0
|
189.5
|
1582.02
|
82.8
|
189.4
|
1582.85
|
83.6
|
189.3
|
1583.69
|
B84.5
|
84.5
|
189.2
|
1584.53
|
85.3
|
189.1
|
1585.36
|
86.2
|
189
|
1586.20
|
87.0
|
188.9
|
1587.04
|
B87.8
|
87.8
|
188.8
|
1587.88
|
88.7
|
188.7
|
1588.73
|
89.5
|
188.6
|
1589.57
|
90.4
|
188.5
|
1590.41
|
B91.2
|
91.2
|
188.4
|
1591.26
|
92.1
|
188.3
|
1592.10
|
92.9
|
188.2
|
1592.95
|
93.7
|
188.1
|
1593.79
|
B94.6
|
94.6
|
188
|
1594.64
|
95.4
|
187.9
|
1595.49
|
96.3
|
187.8
|
1596.34
|
97.1
|
187.7
|
1597.19
|
B98.0
|
98.0
|
187.6
|
1598.04
|
98.8
|
187.5
|
1598.89
|
99.7
|
187.4
|
1599.75
|
00.6
|
187.3
|
1600.60
|
B01.4
|
01.4
|
187.2
|
1601.46
|
02.3
|
187.1
|
1602.31
|
03.1
|
187
|
1603.17
|
04.0
|
186.9
|
1604.03
|
The 32DMX-L card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.8.3 32WSS Card Specifications
The 32WSS card optical specifications are listed in Table A-9.
Note For power specifications, see Table A-1.
Table A-9 32WSS Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Typical
|
Max
|
Units
|
-0.25 dB bandwidth
|
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation.
|
EXP RX => COM TX
|
+/-/95
|
—
|
—
|
pm
|
-0.5 dB bandwidth
|
+/-115
|
—
|
—
|
pm
|
-1.0 dB bandwidth
|
+/-135
|
—
|
—
|
pm
|
-0.25 dB bandwidth
|
Add 1, 32 => COM TX
|
+/-115
|
—
|
—
|
pm
|
-0.5 dB bandwidth
|
+/-135
|
—
|
—
|
pm
|
-1.0 dB bandwidth
|
+/-160
|
—
|
—
|
pm
|
Insertion loss
|
All SOP, any optical switch state, and within whole operating temperature range, connectors included.
|
EXP RX => COM TX
|
—
|
—
|
11.3
|
dB
|
—
|
COM RX => EXP TX
|
—
|
—
|
1.5
|
dB
|
—
|
Add 1, 32 => COM TX
|
—
|
—
|
7.6
|
dB
|
—
|
COM RX => DROP TX
|
6
|
—
|
8.5
|
dB
|
VOA dynamic range
|
—
|
EXP RX => COM TX
|
20
|
—
|
—
|
dB
|
—
|
Add 1, 32 => COM TX
|
25
|
—
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
—
|
mW
|
The 32WSS channel plan is shown in Table A-10. All 32WSS client interfaces must comply with this plan.
Table A-10 32WSS Channel Plan
Channel Number
|
Band
|
Channel ID
|
Frequency (GHz)
|
Wavelength (nm)
|
1
|
1
|
30.3
|
195.9
|
1530.33
|
2
|
31.2
|
195.8
|
1531.12
|
3
|
31.9
|
195.7
|
1531.90
|
4
|
32.6
|
195.6
|
1532.68
|
5
|
2
|
34.2
|
195.4
|
1534.25
|
6
|
35.0
|
195.3
|
1535.04
|
7
|
35.8
|
195.2
|
1535.82
|
8
|
36.6
|
195.1
|
1536.61
|
9
|
3
|
38.1
|
194.9
|
1538.19
|
10
|
38.9
|
194.8
|
1538.98
|
11
|
39.7
|
194.7
|
1539.77
|
12
|
40.5
|
194.6
|
1540.56
|
13
|
4
|
42.1
|
194.4
|
1542.14
|
14
|
42.9
|
194.3
|
1542.94
|
15
|
43.7
|
194.2
|
1543.73
|
16
|
44.5
|
194.1
|
1544.53
|
17
|
5
|
46.1
|
193.9
|
1546.12
|
18
|
46.9
|
193.8
|
1546.92
|
19
|
47.7
|
193.7
|
1547.72
|
20
|
48.5
|
193.6
|
1548.51
|
21
|
6
|
50.1
|
193.4
|
1550.12
|
22
|
50.9
|
193.3
|
1550.92
|
23
|
51.7
|
193.2
|
1551.72
|
24
|
52.5
|
193.1
|
1552.52
|
25
|
7
|
54.1
|
192.9
|
1554.13
|
26
|
54.9
|
192.8
|
1554.94
|
27
|
55.7
|
192.7
|
1555.75
|
28
|
56.5
|
192.6
|
1556.55
|
29
|
8
|
58.1
|
192.4
|
1558.17
|
30
|
58.9
|
192.3
|
1558.98
|
31
|
59.7
|
192.2
|
1559.79
|
32
|
60.6
|
192.1
|
1560.61
|
The 32WSS card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.8.4 32WSS-L Card Specifications
The 32WSS-L card optical specifications are listed in Table A-11.
Note For power specifications, see Table A-1.
Table A-11 32WSS-L Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Typical
|
Max
|
Units
|
-0.1 dB bandwidth
|
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation.
|
EXP RX => COM TX
|
—
|
+/-/57
|
—
|
pm
|
-0.25 dB bandwidth
|
+/-/61
|
+/-/89
|
—
|
-0.5 dB bandwidth
|
+/-91
|
+/-/116
|
—
|
-1.0 dB bandwidth
|
+/-135
|
+/-/149
|
—
|
-0.1 dB bandwidth
|
Add 1, 32 => COM TX
|
+/-32
|
+/-/69
|
—
|
-0.25 dB bandwidth
|
+/-98
|
+/-/129
|
—
|
-0.5 dB bandwidth
|
+/-135
|
+/-/161
|
—
|
-1.0 dB bandwidth
|
+/-160
|
+/-/201
|
—
|
Insertion loss
|
All SOP, any optical switch state, and within whole operating temperature range, connectors included.
|
EXP RX => COM TX
|
—
|
9.7
|
11.3
|
dB
|
COM RX => EXP TX
|
—
|
1.4
|
1.6
|
dB
|
Add 1, 32 => COM TX
|
—
|
6.2
|
8.0
|
dB
|
COM RX => DROP TX
|
6.0
|
8.0
|
8.5
|
dB
|
VOA dynamic range
|
—
|
EXP RX => COM TX
|
20
|
25
|
—
|
dB
|
—
|
Add 1, 32 => COM TX
|
25
|
25
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
—
|
mW
|
The 32WSS-L channel plan is shown in Table A-12. All 32WSS-L client interfaces must comply with this plan.
Table A-12 32WSS-L Channel Plan
Band ID
|
Channel Label
|
Frequency (THz)
|
Wavelength (nm)
|
B77.8
|
77.8
|
190
|
1577.86
|
78.6
|
189.9
|
1578.69
|
79.5
|
189.8
|
1579.52
|
80.3
|
189.7
|
1580.35
|
B81.1
|
81.1
|
189.6
|
1581.18
|
82.0
|
189.5
|
1582.02
|
82.8
|
189.4
|
1582.85
|
83.6
|
189.3
|
1583.69
|
B84.5
|
84.5
|
189.2
|
1584.53
|
85.3
|
189.1
|
1585.36
|
86.2
|
189
|
1586.20
|
87.0
|
188.9
|
1587.04
|
B87.8
|
87.8
|
188.8
|
1587.88
|
88.7
|
188.7
|
1588.73
|
89.5
|
188.6
|
1589.57
|
90.4
|
188.5
|
1590.41
|
B91.2
|
91.2
|
188.4
|
1591.26
|
92.1
|
188.3
|
1592.10
|
92.9
|
188.2
|
1592.95
|
93.7
|
188.1
|
1593.79
|
B94.6
|
94.6
|
188
|
1594.64
|
95.4
|
187.9
|
1595.49
|
96.3
|
187.8
|
1596.34
|
97.1
|
187.7
|
1597.19
|
B98.0
|
98.0
|
187.6
|
1598.04
|
98.8
|
187.5
|
1598.89
|
99.7
|
187.4
|
1599.75
|
00.6
|
187.3
|
1600.60
|
B01.4
|
01.4
|
187.2
|
1601.46
|
02.3
|
187.1
|
1602.31
|
03.1
|
187
|
1603.17
|
04.0
|
186.9
|
1604.03
|
The 32WSS-L card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.8.5 40-MUX-C Card Specifications
The 40-MUX-C card optical specifications are listed in Table A-13.
Note For power specifications, see Table A-1.
Table A-13 40-MUX-C Card Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Transmit (Tx) filter shape
|
All standard operating procedures (SOP) and within whole operating temperature range
|
-1 dB bandwidth,
RX 1, 40 => COM TX
|
+/-100
|
—
|
pm
|
-3 dB bandwidth,
RX 1, 40 => COM TX
|
+/-199
|
—
|
pm
|
Insertion loss
|
All SOP and within whole operating temperature range
|
RX 1, 40 => COM TX
|
|
5.8
|
dB
|
VOA dynamic range
|
—
|
RX 1, 40 => COM TX
|
25
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The 40-MUX-C card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.8.6 40-DMX-C Card Specifications
The 40-DMX-C card optical specifications are listed in Table A-14.
Note For power specifications, see Table A-1.
Table A-14 40-DMX-C Card Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Receive (Rx) filter shape
|
All SOP and within whole operating temperature range
|
-1 dB bandwidth,
COM RX => TX 1, 40 (OUT)
|
+/-100
|
—
|
pm
|
-3 dB bandwidth,
COM RX => TX 1, 40 (OUT)
|
+/-199
|
—
|
pm
|
Insertion loss
|
All SOP and within whole operating temperature range
|
COM RX => TX 1, 40
|
—
|
5.8
|
dB
|
VOA dynamic range
|
—
|
COM RX => TX 1, 40
|
25
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The 40-DMX-C card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.8.7 40-DMX-CE Card Specifications
The 40-DMX-CE card optical specifications are listed in Table A-15.
Note For power specifications, see Table A-1.
Table A-15 40-DMX-CE Card Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Receive (Rx) filter shape
|
All SOP and within whole operating temperature range
|
-1 dB bandwidth,
COM RX => TX 1, 40 (OUT)
|
+/-100
|
—
|
pm
|
-3 dB bandwidth,
COM RX => TX 1, 40 (OUT)
|
+/-199
|
—
|
pm
|
Insertion loss
|
All SOP and within whole operating temperature range
|
COM RX => TX 1, 40
|
—
|
5.8
|
dB
|
VOA dynamic range
|
—
|
COM RX => TX 1, 40
|
25
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The 40-DMX-CE card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
A.8.8 40-WSS-C Card Specifications
The 40-WSS-C card optical specifications are listed in Table A-16.
Note For power specifications, see Table A-1.
Table A-16 40-WSS-C Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Channel grid: -0.1 dB
|
All SOP and within whole operating temperature range
|
EXP_RX to COM_ TX
|
—
|
—
|
pm
|
Channel grid: -0.25 dB
|
+/- 61
|
—
|
pm
|
Channel grid: -0.5 dB
|
+/- 91
|
—
|
pm
|
Channel grid: -1.0 dB
|
+/- 135
|
—
|
pm
|
Channel grid: -0.1 dB
|
All SOP and within whole operating temperature range
|
EXP_RX to COM_ TX
|
+/- 32
|
—
|
pm
|
Channel grid: -0.25 dB
|
+/- 98
|
—
|
pm
|
Channel grid: -0.5 dB
|
+/- 135
|
—
|
pm
|
Channel grid: -1.0 dB
|
+/- 160
|
—
|
pm
|
Insertion loss
|
All SOP and within whole operating temperature range
|
EXP_RX to COM_ TX
|
—
|
7.5
|
dB
|
EXP_RX to COM_ TX
|
—
|
2.3
|
dB
|
EXP_RX to COM_ TX
|
—
|
6.0
|
dB
|
EXP_RX to COM_ TX
|
—
|
6.8
|
dB
|
VOA dynamic range
|
—
|
EXP_RX to COM_ TX
|
20
|
—
|
dB
|
EXP_RX to COM_ TX
|
25
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The 40-WSS-C card channel grid is listed in Table A-17.
Table A-17 40-WSS-C Channel Grid
Band ID
|
Channel Label
|
Frequency (THz)
|
Wavelength (nm)
|
B30.3
|
30.3
|
195.9
|
1530.33
|
31.1
|
195.8
|
1531.12
|
31.9
|
195.7
|
1531.90
|
32.6
|
195.6
|
1532.68
|
33.4
|
195.5
|
1533.47
|
B34.2
|
34.2
|
195.4
|
1534.25
|
35.0
|
195.3
|
1535.04
|
35.8
|
195.2
|
1535.82
|
36.6
|
195.1
|
1536.61
|
37.4
|
195.0
|
1537.4
|
B38.1
|
38.1
|
194.9
|
1538.19
|
38.9
|
194.8
|
1538.98
|
39.7
|
194.7
|
1539.77
|
40.5
|
194.6
|
1540.56
|
41.3
|
194.5
|
1541.35
|
B42.1
|
42.1
|
194.4
|
1542.14
|
42.9
|
194.3
|
1542.94
|
43.7
|
194.2
|
1543.73
|
44.5
|
194.1
|
1544.53
|
45.3
|
194.0
|
1545.32
|
B46.1
|
46.1
|
193.9
|
1546.12
|
46.9
|
193.8
|
1546.92
|
47.7
|
193.7
|
1547.72
|
48.5
|
193.6
|
1548.51
|
49.3
|
193.5
|
1549.32
|
B50.1
|
50.1
|
193.4
|
1550.12
|
50.9
|
193.3
|
1550.92
|
51.7
|
193.2
|
1551.72
|
52.5
|
193.1
|
1552.52
|
53.3
|
193.0
|
1553.33
|
54.1
|
54.1
|
192.9
|
1544.13
|
54.9
|
192.8
|
1544.94
|
55.7
|
192.7
|
1555.75
|
56.5
|
192.6
|
1556.55
|
57.3
|
192.5
|
1557.36
|
B58.1
|
58.1
|
192.4
|
1558.17
|
58.9
|
192.3
|
1558.98
|
59.7
|
192.2
|
1559.79
|
60.6
|
192.1
|
1560.61
|
61.4
|
192.0
|
1561.42
|
The 40-WSS-C card has the following additional specifications:
•Dimensions
–Height: 8.66 in. (220 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 1.42 in. (36 mm)
A.8.9 40-WSS-CE Card Specifications
The 40-WSS-CE card optical specifications are listed in Table A-18.
Note For power specifications, see Table A-1.
Table A-18 40-WSS-C Card Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Channel grid: -0.1 dB
|
All SOP and within whole operating temperature range
|
EXP RX greater than or equal to COM TX
|
—
|
—
|
pm
|
Channel grid: -0.25 dB
|
+/- 61
|
—
|
pm
|
Channel grid: -0.5 dB
|
+/- 91
|
—
|
pm
|
Channel grid: -1.0 dB
|
+/- 135
|
—
|
pm
|
Channel grid: -0.1 dB
|
All SOP and within whole operating temperature range
|
Add 1, 40 greater than or equal to COM TX
|
+/- 32
|
—
|
pm
|
Channel grid: -0.25 dB
|
+/- 98
|
—
|
pm
|
Channel grid: -0.5 dB
|
+/- 135
|
—
|
pm
|
Channel grid: -1.0 dB
|
+/- 160
|
—
|
pm
|
Insertion loss
|
All SOP and within whole operating temperature range
|
EXP RX greater than or equal to COM TX
|
—
|
7.5
|
dB
|
COM RX greater than or equal to EXP TX
|
—
|
2.3
|
dB
|
Add 1, 40 greater than or equal to COM TX
|
—
|
6.0
|
dB
|
COM RX greater than or equal to DROP TX
|
—
|
6.8
|
dB
|
VOA dynamic range
|
—
|
EXP RX greater than COM TX
|
20
|
—
|
dB
|
Add 1, 40 greater than or equal to COM TX
|
25
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The 40-WSS-CE card channel grid is listed in Table A-19.
Table A-19 40-WSS-C Card Channel Grid
Band ID
|
Channel Label
|
Frequency (THz)
|
Wavelength (nm)
|
B30.7
|
30.7
|
195.85
|
1530.72
|
31.5
|
195.75
|
1531.51
|
32.3
|
195.65
|
1532.29
|
33.1
|
195.55
|
1533.07
|
33.9
|
195.45
|
1533.86
|
B34.6
|
34.6
|
195.35
|
1534.64
|
35.4
|
195.25
|
1535.43
|
36.2
|
195.15
|
1536.22
|
37.0
|
195.05
|
1537.00
|
37.8
|
194.95
|
1537.79
|
B38.6
|
38.6
|
194.85
|
1538.58
|
39.4
|
194.75
|
1539.37
|
40.1
|
194.65
|
1540.16
|
40.9
|
194.55
|
1540.95
|
41.8
|
194.45
|
1541.75
|
B42.5
|
42.5
|
194.35
|
1542.54
|
43.3
|
194.25
|
1543.33
|
44.1
|
194.15
|
1544.13
|
44.9
|
194.05
|
1544.92
|
45.7
|
193.95
|
1545.72
|
B46.5
|
46.5
|
193.85
|
1546.52
|
47.3
|
193.75
|
1547.32
|
48.1
|
193.65
|
1548.11
|
48.9
|
193.55
|
1548.91
|
49.7
|
193.45
|
1549.72
|
B50.5
|
50.5
|
193.35
|
1550.52
|
51.3
|
193.25
|
1551.32
|
52.1
|
193.15
|
1552.12
|
52.9
|
193.05
|
1552.93
|
53.7
|
192.95
|
1553.73
|
B54.4
|
54.4
|
192.85
|
1554.54
|
55.3
|
192.75
|
1555.34
|
56.1
|
192.65
|
1556.15
|
56.9
|
192.55
|
1556.96
|
57.8
|
192.45
|
1557.77
|
B58.6
|
58.6
|
192.35
|
1558.58
|
59.4
|
192.25
|
1559.39
|
60.2
|
192.15
|
1560.20
|
61.0
|
192.05
|
1561.01
|
61.8
|
191.95
|
1561.83
|
The 40-WSS-CE card has the following additional specifications:
•Dimensions
–Height: 8.66 in. (220 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 1.42 in. (36 mm)
A.8.10 40-WXC-C Card Specifications
The 40-WXC-C card optical specifications are listed in Table A-20.
Note For power specifications, see Table A-1.
Table A-20 40-WXC-C Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Channel bandwidth: -0.25 dB
|
All SOP and within whole operating temperature range
|
All paths
|
—
|
—
|
GHz
|
Channel bandwidth: -0.5 dB
|
+/- 20.5
|
—
|
GHz
|
Channel bandwidth: -1.5 dB
|
—
|
—
|
GHz
|
Channel bandwidth: -03.0 dB
|
+/- 37.5
|
—
|
GHz
|
Insertion loss
|
All SOP and within whole operating temperature range
|
All paths
|
—
|
8.5
|
dB
|
VOA dynamic range
|
—
|
All paths
|
20
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The 40-WXC-C card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm) for a standard DWDM unit
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm) for a standard DWDM unit
A.8.11 80-WXC-C Card Specifications
The 80-WXC-C card optical specifications are listed in Table A-21.
Note For power specifications, see Table A-1.
Table A-21 80-WXC-C Card Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Channel grid
|
50 GHz spaced standard ITU Grid and Channel Zero at 1529.55nm (196 THz)
|
|
191.95
|
196.00
|
THz
|
Operating Wavelength Bandwidth
|
All SOP; and within whole operating temperature range; connectors included and for minimum operating attenuation
|
All paths
|
+/- 12.5
|
—
|
GHz
|
Channel bandwidth: -0.25 dB
|
Vendor provided 1
|
—
|
GHz
|
Channel bandwidth: -0.5 dB
|
+/- 12.5
|
—
|
Channel bandwidth: -1.5 dB
|
+/- 17
|
—
|
Channel bandwidth: -03.0 dB
|
Vendor provided 1
|
—
|
Insertion loss
|
All SOP; any optical switch state and within whole operating temperature range; connectors included and for minimum attenuation
|
All paths
|
2.0
|
7.0
|
dB
|
VOA dynamic range
|
—
|
All paths
|
25
|
—
|
dB
|
Maximum optical input power
|
—
|
All ports
|
500
|
—
|
mW
|
The 80-WXC-C card has the following additional specifications:
•Dimensions
–Height: 13.11 in. (333 mm) for a standard DWDM unit
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth:9.88 in. (251 mm) for a standard DWDM unit
A.8.12 40-SMR1-C Card Specifications
The 40-SMR1-C card optical specifications are listed in Table A-22.
Note For power specifications, see Table A-1.
Table A-22 40-SMR1-C Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Channel bandwidth: -0.25 dB
|
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation
|
All WXC paths (ADD-RX to LINE-TX and EXP-RX to LINE-TX)
|
—
|
—
|
pm
|
Channel bandwidth: -0.5 dB
|
+/- 160
|
—
|
pm
|
Channel bandwidth: -1.5 dB
|
—
|
—
|
pm
|
Channel bandwidth: -3.0 dB
|
+/- 240
|
—
|
pm
|
Insertion loss
|
All SOP, any optical switch state, and within whole operating temperature range, connectors included
|
All WXC paths (ADD-RX to LINE-TX and EXP-RX to LINE-TX)
|
2.0
|
8.1
|
dB
|
All SOP, within whole operating temperature range, connectors included
|
DROP-TX with respect to EXP-TX
|
—
|
5.3
|
dB
|
VOA dynamic range
|
—
|
All WXC paths (ADD-RX to LINE-TX and EXP-RX to LINE-TX)
|
20
|
—
|
dB
|
DROP-TX
|
—
|
25
|
dB
|
Maximum optical input power
|
Total power sum of all ports
|
—
|
500
|
—
|
mW
|
The EDFA1 amplifier within the 40-SMR1-C card has the following specifications:
•Optical characteristics (specified from LINE-RX to EXP-TX)
–Total operating wavelength range: 1530 to 1561.5 nm
–Gain ripple (peak to valley): 1.2 dB
–Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 0 to 9 dB
–Gain range: 7 to 38 dB
–Minimum gain (standard range): 7.0 dB
–Maximum gain (standard range with programmable gain tilt): 21 dB
–Maximum gain (extended range with uncontrolled gain tilt): 38 dB
–Gain and power regulation over/undershoot: 0.5 dB
–Maximum output power (with full channel load): 17 dBm
–Minimum output power (with one channel): -5 dBm
–Input power (pin) range at full channel load: -21 to 12 dBm
–Input power (pin) range at single channel load: -43 to -10 dBm
–Noise figure at G = 21 dB = 7.5 dB
The OSC filter within the 40-SMR1-C card has the following specifications:
•OSC filter drop (OSC) insertion loss maximum: 1.8 dB
•OSC filter add (OSC) insertion loss maximum: 1.3 dB
The 40-SMR1-C card has the following additional specifications:
•Dimensions
–Height: 13.11 in. (333 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.88 in. (251 mm)
A.8.13 40-SMR2-C Card Specifications
The 40-SMR2-C card optical specifications are listed in Table A-23.
Note For power specifications, see Table A-1.
Table A-23 40-SMR2-C Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Channel bandwidth: -0.25 dB
|
All SOP and within whole operating temperature range, connectors included, and for maximum VOA operating attenuation
|
All WXC paths (ADD-RX to WXC output, EXP1-RX to WXC output, EXP2-RX to WXC output, and EXP3-RX to WXC output)
|
—
|
—
|
pm
|
Channel bandwidth: -0.5 dB
|
+/- 160
|
—
|
pm
|
Channel bandwidth: -1.5 dB
|
—
|
—
|
pm
|
Channel bandwidth: -3.0 dB
|
+/- 240
|
—
|
pm
|
Insertion loss
|
All SOP, any optical switch state, and within whole operating temperature range, connectors included
|
All WXC paths (ADD-RX to WXC output, EXP1-RX to WXC output, EXP2-RX to WXC output, and EXP3-RX to WXC output)
|
2.0
|
7
|
dB
|
All SOP, within whole operating temperature range, connectors included
|
DROP-TX with respect to EXP-TX
|
—
|
5.3
|
dB
|
VOA dynamic range
|
—
|
All WXC paths (ADD-RX to WXC output, EXP1-RX to WXC output, EXP2-RX to WXC output, and EXP3-RX to WXC output)
|
20
|
—
|
dB
|
DROP-TX
|
—
|
25
|
dB
|
Maximum optical input power
|
Total power sum of all ports
|
—
|
500
|
—
|
mW
|
The EDFA1 amplifier within the 40-SMR2-C card has the following specifications:
•Optical characteristics (specified from LINE-RX to EXP-TX)
–Total operating wavelength range: 1530 to 1561.5 nm
–Gain ripple (peak to valley): 1.2 dB
–Mid-access loss (MAL) range (for dispersion compensation unit [DCU]): 0 to 9 dB
–Gain range: 7 to 38 dBm in constant gain mode
–Minimum gain (standard range): 7.0 dBm
–Maximum gain (standard range with programmable gain tilt): 21 dBm
–Maximum gain (extended range with uncontrolled gain tilt): 38 dBm
–Gain and power regulation over/undershoot: 0.5 dB
–Maximum output power (with full channel load): 17 dBm
–Minimum output power (with one channel): -5 dBm
–Input power (pin) range at full channel load: -21 to 12 dBm
–Input power (pin) range at single channel load: -43 to -10 dBm
–Noise figure at G= 21 dB = 7.5 dB
The EDFA2 amplifier within the 40-SMR2-C card has the following specifications:
•Optical characteristics (specified from WXC output to LINE-TX)
–Total operating wavelength range 1530.0 to 1561.5 nm
–Gain ripple (peak to valley): 1.2 dB
–Gain range: 13 to 26 dB
–Optimal gain (gain tilt = 0): 17 dB
–Gain and power regulation over/undershoot: 0.5 dB
–Minimum output power (with one channel): -5 dBm
–Input power range (full channel load): -9 to 4 dBm
–Input power range (single channel load): -31 to -18 dBm
–Noise figure at G=17dB = 6 dB maximum
The OSC filter within the 40-SMR2-C card has the following specifications:
•OSC filter drop (OSC) insertion loss maximum: 1.8 dB
•OSC filter add (OSC) insertion loss maximum: 1.3 dB
The 40-SMR2-C card has the following additional specifications:
•Dimensions
–Height: 13.11 in. (333 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.88 in. (251 mm)
A.8.14 MMU Card Specifications
The MMU card optical specifications are listed in Table A-24.
Note For power specifications, see Table A-1.
Table A-24 MMU Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Typical
|
Max
|
Units
|
Operating bandwidth
|
All SOP, any optical switch state, and within whole operating temperature range, connectors included.
|
All paths
|
1500
|
—
|
1605
|
nm
|
Insertion loss
|
All SOP, any optical switch state, and within whole operating temperature range, connectors included.
|
EXP RX => COM TX
|
—
|
—
|
7.0
|
dB
|
EXP A RX => COM TX
|
—
|
—
|
2.3
|
dB
|
COM RX => EXP TX
|
—
|
—
|
0.8
|
dB
|
COM RX => EXP A TX
|
—
|
—
|
14.8
|
dB
|
Wavelength dependent losses
|
All SOP, any optical switch state, and within whole operating temperature range, connectors included.
|
C-band only
|
—
|
—
|
0.3
|
dB
|
L-band only
|
—
|
—
|
0.3
|
dB
|
C and L bands
|
—
|
—
|
0.5
|
dB
|
Polarization dependent loss (PDL)
|
—
|
C-band only
|
—
|
—
|
0.2
|
dB
|
—
|
L-band only
|
—
|
—
|
0.2
|
dB
|
—
|
C and L bands
|
—
|
—
|
0.3
|
dB
|
Chromatic dispersion
|
|
All paths
|
-20
|
—
|
+20
|
ps/nm
|
Polarization mode dispersion (PMD)
|
—
|
All paths
|
—
|
—
|
0.1
|
ps
|
Optical power reading resolution
|
—
|
All photodiodes (both real and virtual)
|
—
|
—
|
0.1
|
dB
|
Optical power reading precision
|
—
|
-0.1
|
—
|
0.1
|
dB
|
Directivity
|
All SOP, any optical switch state, and within whole operating temperature range, connectors included.
|
EXP RX => EXP A RX
|
40
|
—
|
—
|
dB
|
EXP RX => EXP B RX
|
40
|
—
|
—
|
dB
|
EXP A RX => EXP B RX
|
40
|
—
|
—
|
dB
|
Return loss
|
—
|
—
|
40
|
—
|
—
|
dB
|
Maximum optical input power
|
Maximum handling power
|
—
|
500
|
—
|
—
|
mW
|
The MMU card has the following additional specifications:
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 8.66 in. (220.1 mm)
A.9 Optical Add/Drop Cards
This section provides specifications for the AD-IC-xx.x, AD-2C-xx.x, AD-4C-xx.x, AD-1B-xx.x, and AD-4B-xx.x cards.
A.9.1 AD-1C-xx.x Card Specifications
Table A-25 lists the AD-1C-xx.x optical specifications.
Table A-25 AD-1C-xx.x Card Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Trx filter shape
(-0.5 dB bandwidth)
TrxBW2
|
All SOP and within whole operating temperature range
|
COM Rx—xx.xx Tx
xx.xx Rx—COM Tx
|
+/-180
|
—
|
pm
|
Rfx filter shape
(-0.5 dB bandwidth)
RfxBW2
|
All SOP and within whole operating temperature range
|
COM Rx—Exp Tx
Exp Rx—COM Tx
|
+/-180
|
—
|
pm
|
Insertion loss
(drop section)
|
All SOP and within whole operating temperature range (two connectors included)
|
COM Rx—xx.xx Tx
|
—
|
2.0
|
dB
|
Insertion loss
(express section)
|
VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)
|
COM Rx—Exp Tx
Exp Rx—COM Tx
|
—
|
2.4 or 1.2
|
dB
|
Insertion loss
(add section)
|
VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)
|
xx.xx Rx—COM Tx
|
—
|
2.6
|
dB
|
VOA dynamic range
|
—
|
—
|
30
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The AD-1C-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.
The AD-1C-xx.x card has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.9.2 AD-2C-xx.x Card Specifications
Table A-26 lists the AD-2C-xx.x optical specifications.
Table A-26 AD-2C-xx.x Card Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Trx filter shape
(-0.5 dB bandwidth)
TrxBW2
|
All SOP and within whole operating temperature range
|
COM Rx—xx.xx Tx
COM Rx—yy.yy Tx
|
+/-180
|
—
|
pm
|
xx.xx Rx—COM Tx
yy.yy Rx—COM Tx
|
+/-180
|
—
|
Rfx filter shape
(-0.5 dB bandwidth)
RfxBW2
|
All SOP and within whole operating temperature range
|
COM Rx—Exp Tx
Exp Rx—COM Tx
|
+/-180
|
—
|
pm
|
Insertion loss
(drop section)
|
All SOP and within whole operating temperature range (two connectors included)
|
COM Rx—xx.xx Tx
|
—
|
2.0
|
dB
|
COM Rx—yy.yy Tx
|
—
|
2.4
|
dB
|
Insertion loss
(express section)
|
VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)
|
COM Rx—Exp Tx
|
—
|
2.7
|
dB
|
Exp Rx—COM Tx
|
—
|
1.6
|
dB
|
Insertion loss
(add section)
|
VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)
|
xx.xx Rx—COM Tx
|
—
|
3.1
|
dB
|
yy.yy Rx—COM Tx
|
—
|
2.7
|
dB
|
VOA dynamic range
|
—
|
—
|
30
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The AD-2C-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.
The AD-2C-xx.x has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.9.3 AD-4C-xx.x Card Specifications
Table A-27 lists the AD-4C-xx.x optical specifications.
Table A-27 AD-4C-xx.x Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Channel grid
|
See Table A-28. The channel plan for the AD-4C-xx.x card is identical to the channel plan for the AD-1B-xx.x card.
|
—
|
—
|
—
|
—
|
Trx filter shape
(-0.5 dB bandwidth)
TrxBW2
|
All SOP and within whole operating temperature range
|
COM Rx—xx.xx Tx
COM Rx—yy.yy Tx
COM Rx—zz.zz Tx
COM Rx—kk.kk Tx
xx.xx Rx—COM Tx
yy.yy Rx—COM Tx
|
+/-180
|
—
|
pm
|
|
Rfx filter shape
(-1 dB bandwidth)
RfxBW2
|
All SOP and within whole operating temperature range
|
COM Rx—Exp Tx
Exp Rx—COM Tx
|
—
|
—
|
pm
|
Insertion loss
(drop section)
|
All SOP and within whole operating temperature range (two connectors included)
|
COM Rx—xx.xx Tx
|
—
|
5.5
|
dB
|
COM Rx—yy.yy Tx
|
—
|
5.0
|
dB
|
COM Rx—zz.zz Tx
|
—
|
4.5
|
dB
|
COM Rx—kk.kk Tx
|
—
|
4.1
|
dB
|
Insertion loss
(express section)
|
VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)
|
COM Rx—Exp Tx
|
—
|
2.7
|
dB
|
Exp Rx—COM Tx
|
—
|
1.2
|
dB
|
Insertion loss
(add section)
|
VOA at minimum attenuation; all SOP and within whole operating temperature range (two connectors included)
|
xx.xx Rx—COM Tx
|
—
|
3.9
|
dB
|
yy.yy Rx—COM Tx
|
—
|
4.3
|
dB
|
zz.zz Rx—COM Tx
|
—
|
4.5
|
dB
|
kk.kk Rx—COM Tx
|
—
|
4.9
|
dB
|
VOA dynamic range
|
—
|
—
|
30
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
The AD-4C-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.
The AD-4C-xx.x has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.9.4 AD-1B-xx.x Card Specifications
Table A-28 lists the unit names, band IDs, channel IDs, frequencies, and wavelengths assigned to the eight versions of the AD-1B-xx.x card.
Table A-28 AD-1B-xx.x Channel Allocation Plan by Band
Unit Name
|
Band ID
|
Channel ID
|
Frequency (GHz)
|
Wavelength (nm)
|
AD-1B-30.3
|
B30.3
|
30.3
|
195.9
|
1530.33
|
30.7
|
195.85
|
1530.72
|
31.1
|
195.8
|
1531.12
|
31.5
|
195.75
|
1531.51
|
31.9
|
195.7
|
1531.90
|
32.2
|
195.65
|
1532.29
|
32.6
|
195.6
|
1532.68
|
33.3
|
195.55
|
1533.07
|
AD-1B-34.2
|
B34.2
|
34.2
|
195.4
|
1534.25
|
34.6
|
195.35
|
1534.64
|
35.0
|
195.3
|
1535.04
|
35.4
|
195.25
|
1535.43
|
35.8
|
195.2
|
1535.82
|
36.2
|
195.15
|
1536.22
|
36.6
|
195.1
|
1536.61
|
37.0
|
195.05
|
1537.00
|
AD-1B-38.1
|
B38.1
|
38.1
|
194.9
|
1538.19
|
38.5
|
194.85
|
1538.58
|
38.9
|
194.8
|
1538.98
|
39.3
|
194.75
|
1539.37
|
39.7
|
194.7
|
1539.77
|
40.1
|
194.65
|
1540.16
|
40.5
|
194.6
|
1540.56
|
40.9
|
194.55
|
1540.95
|
AD-1B-42.2
|
B42.1
|
42.1
|
194.4
|
1542.14
|
42.5
|
194.35
|
1542.54
|
42.9
|
194.3
|
1542.94
|
43.3
|
194.25
|
1543.33
|
43.7
|
194.2
|
1543.73
|
44.1
|
194.15
|
1544.13
|
44.5
|
194.1
|
1544.53
|
44.9
|
194.05
|
1544.92
|
AD-1B-46.1
|
B46.1
|
46.1
|
193.9
|
1546.12
|
46.5
|
193.85
|
1546.52
|
46.9
|
193.8
|
1546.92
|
47.3
|
193.75
|
1547.32
|
47.7
|
193.7
|
1547.72
|
48.1
|
193.65
|
1548.11
|
48.5
|
193.6
|
1548.51
|
48.9
|
193.55
|
1548.91
|
AD-1B-50.1
|
B50.1
|
50.1
|
193.4
|
1550.12
|
50.5
|
193.35
|
1550.52
|
50.9
|
193.3
|
1550.92
|
51.3
|
193.25
|
1551.32
|
51.7
|
193.2
|
1551.72
|
52.1
|
193.15
|
1552.12
|
52.5
|
193.1
|
1552.52
|
52.9
|
193.05
|
1552.93
|
AD-1B-54.1
|
B54.1
|
54.1
|
192.9
|
1554.13
|
54.5
|
192.85
|
1554.54
|
54.9
|
192.8
|
1554.94
|
55.3
|
192.75
|
1555.34
|
55.7
|
192.7
|
1555.75
|
56.1
|
192.65
|
1556.15
|
56.5
|
192.6
|
1556.96
|
56.9
|
192.55
|
1556.96
|
AD-1B-58.1
|
B58.1
|
58.1
|
192.4
|
1558.17
|
58.5
|
192.35
|
1558.58
|
58.9
|
192.3
|
1558.98
|
59.3
|
192.25
|
1559.39
|
59.7
|
192.2
|
1559.79
|
60.2
|
192.15
|
1560.20
|
60.6
|
192.1
|
1560.61
|
61.0
|
192.05
|
1561.01
|
Table A-29 lists AD-1B-xx.x optical specifications.
Table A-29 AD-1B-xx.x Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
-1 dB bandwidth
|
All SOP and within whole operating environmental range
|
COM Rx—Band Tx
Band Rx—COM Tx
|
3.6
|
—
|
nm
|
-1 dB bandwidth
|
All SOP and within whole operating temperature range
|
COM Rx—Exp Tx
Exp Rx—COM Tx
|
See Table A-30.
|
nm
|
Insertion loss
(drop section)
|
All SOP and within whole operating environmental range; two connectors included, VOA set at minimum attenuation
|
COM Rx—Band Tx
|
—
|
3.0
|
dB
|
Insertion loss
(express section)
|
All SOP and within whole operating environmental range; two connectors included
|
Exp Rx—COM Tx
|
—
|
1.6
|
dB
|
All SOP and within whole operating environmental range; two connectors included, VOA set at its minimum attenuation
|
COM Rx—Exp Tx
|
—
|
2.2
|
dB
|
Insertion loss
(add section)
|
All SOP and within whole operating environmental range; two connectors included
|
Band Rx—COM Tx
|
—
|
2.2
|
dB
|
VOA dynamic range
|
—
|
—
|
30
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
Table A-30 lists the range of wavelengths for the receive (express) band.
Table A-30 AD-1B-xx.x Transmit and Receive Dropped Band Wavelength Ranges
Tx (Dropped) Band
|
Rx (Express) Band
|
Left Side (nm)
|
Right Side (nm)
|
B30.3
|
—
|
Wavelengths 1533.825 or higher
|
B34.2
|
Wavelengths 1533.395 or lower
|
Wavelengths 1537.765 or higher
|
B38.1
|
Wavelengths 1537.325 or lower
|
Wavelengths 1541.715 or higher
|
42.1
|
Wavelengths 1541.275 or lower
|
Wavelengths 1545.695 or higher
|
46.1
|
Wavelengths 1545.245 or lower
|
Wavelengths 1549.695 or higher
|
50.1
|
Wavelengths 1549.235 or lower
|
Wavelengths 1553.705 or higher
|
54.1
|
Wavelengths 1553.255 or lower
|
Wavelengths 1557.745 or higher
|
58.1
|
Wavelengths 1557.285 or lower
|
—
|
The AD-1B-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.
The AD-1B-xx.x card has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.9.5 AD-4B-xx.x Card Specifications
Table A-31 lists the unit names, band IDs, channel IDs, frequencies, and wavelengths assigned to the two versions of the card.
Table A-31 AD-4B-xx.x Channel Allocation Plan by Band
Unit Name
|
Band ID
|
Channel ID
|
Frequency (GHz)
|
Wavelength (nm)
|
AD-4B-30.3
|
B30.3
|
30.3
|
195.9
|
1530.33
|
30.7
|
195.85
|
1530.72
|
31.1
|
195.8
|
1531.12
|
31.5
|
195.75
|
1531.51
|
31.9
|
195.7
|
1531.90
|
32.2
|
195.65
|
1532.29
|
32.6
|
195.6
|
1532.68
|
33.3
|
195.55
|
1533.07
|
B34.2
|
34.2
|
195.4
|
1534.25
|
34.6
|
195.35
|
1534.64
|
35.0
|
195.3
|
1535.04
|
35.4
|
195.25
|
1535.43
|
35.8
|
195.2
|
1535.82
|
36.2
|
195.15
|
1536.22
|
36.6
|
195.1
|
1536.61
|
37.0
|
195.05
|
1537.00
|
B38.1
|
38.1
|
194.9
|
1538.19
|
38.5
|
194.85
|
1538.58
|
38.9
|
194.8
|
1538.98
|
39.3
|
194.75
|
1539.37
|
39.7
|
194.7
|
1539.77
|
40.1
|
194.65
|
1540.16
|
40.5
|
194.6
|
1540.56
|
40.9
|
194.55
|
1540.95
|
B42.1
|
42.1
|
194.4
|
1542.14
|
42.5
|
194.35
|
1542.54
|
42.9
|
194.3
|
1542.94
|
43.3
|
194.25
|
1543.33
|
43.7
|
194.2
|
1543.73
|
44.1
|
194.15
|
1544.13
|
44.5
|
194.1
|
1544.53
|
44.9
|
194.05
|
1544.92
|
AD-4B-46.1
|
B46.1
|
46.1
|
193.9
|
1546.12
|
46.5
|
193.85
|
1546.52
|
46.9
|
193.8
|
1546.92
|
47.3
|
193.75
|
1547.32
|
47.7
|
193.7
|
1547.72
|
48.1
|
193.65
|
1548.11
|
48.5
|
193.6
|
1548.51
|
48.9
|
193.55
|
1548.91
|
B50.1
|
50.1
|
193.4
|
1550.12
|
50.5
|
193.35
|
1550.52
|
50.9
|
193.3
|
1550.92
|
51.3
|
193.25
|
1551.32
|
51.7
|
193.2
|
1551.72
|
52.1
|
193.15
|
1552.12
|
52.5
|
193.1
|
1552.52
|
52.9
|
193.05
|
1552.93
|
B54.1
|
54.1
|
192.9
|
1554.13
|
54.5
|
192.85
|
1554.54
|
54.9
|
192.8
|
1554.94
|
55.3
|
192.75
|
1555.34
|
55.7
|
192.7
|
1555.75
|
56.1
|
192.65
|
1556.15
|
56.5
|
192.6
|
1556.96
|
56.9
|
192.55
|
1556.96
|
B58.1
|
58.1
|
192.4
|
1558.17
|
58.5
|
192.35
|
1558.58
|
58.9
|
192.3
|
1558.98
|
59.3
|
192.25
|
1559.39
|
59.7
|
192.2
|
1559.79
|
60.2
|
192.15
|
1560.20
|
60.6
|
192.1
|
1560.61
|
61.0
|
192.05
|
1561.01
|
Table A-32 lists AD-4B-xx.x optical specifications.
Table A-32 AD-4B-xx.x Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
-1 dB bandwidth
|
All SOP and within whole operating environmental range
|
COM Rx—Band Tx
Band Rx—COM Tx
|
3.6
|
—
|
nm
|
-1 dB bandwidth
|
All SOP and within whole operating temperature range
|
COM Rx—Exp Tx
Exp Rx—COM Tx
|
Refer to Table A-33.
|
nm
|
Insertion loss
(drop section)
|
All SOP and within whole operating environmental range; two connectors included, VOA set at minimum attenuation
|
COM Rx—Band Tx
30.3/46.1
|
—
|
2.9
|
dB
|
COM Rx—Band Tx
34.2/50.1
|
—
|
3.3
|
dB
|
COM Rx—Band Tx
38.1/54.1
|
—
|
3.8
|
dB
|
COM Rx—Band Tx
42.1/58.1
|
—
|
4.5
|
dB
|
Insertion loss
(express section)
|
All SOP and within whole operating environmental range; two connectors included
|
Exp Rx—COM Tx
|
—
|
4.9
|
dB
|
All SOP and within whole operating environmental range; two connectors included, VOA set at its minimum attenuation
|
COM Rx—Exp Tx
|
—
|
3
|
dB
|
Insertion loss
(add section)
|
All SOP and within whole operating environmental range; two connectors included
|
Band Rx 30.3/46.1—COM Tx
|
—
|
3.5
|
dB
|
Band Rx 34.2/50.1—COM Tx
|
—
|
2.8
|
dB
|
Band Rx 38.1/54.1—COM Tx
|
—
|
2.3
|
dB
|
Band Rx 42.1/58.1—COM Tx
|
—
|
1.8
|
dB
|
VOA dynamic range
|
—
|
—
|
30
|
—
|
dB
|
Maximum optical input power
|
—
|
—
|
300
|
—
|
mW
|
Table A-33 lists the range of wavelengths for the receive (express) band.
Table A-33 AD-4B-xx.x Transmit and Receive Dropped Band Wavelength Ranges
Tx (Dropped) Band
|
Rx (Express) Band
|
Left Side (nm)
|
Right Side (nm)
|
B30.3
|
—
|
Wavelengths 1533.825 or higher
|
B34.2
|
Wavelengths 1533.395 or lower
|
Wavelengths 1537.765 or higher
|
B38.1
|
Wavelengths 1537.325 or lower
|
Wavelengths 1541.715 or higher
|
B42.1
|
Wavelengths 1541.275 or lower
|
Wavelengths 1545.695 or higher
|
B46.1
|
Wavelengths 1545.245 or lower
|
Wavelengths 1549.695 or higher
|
B50.1
|
Wavelengths 1549.235 or lower
|
Wavelengths 1553.705 or higher
|
B54.1
|
Wavelengths 1553.255 or lower
|
Wavelengths 1557.745 or higher
|
B58.1
|
Wavelengths 1557.285 or lower
|
—
|
The AD-4B-xx.x card optical input and output power varies with amplifier output levels and the class of transponder interfaces used. See Table 8-3 through Table 8-7 for this information.
The AD-4B-xx.x has the following additional specifications:
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.0 in. (228.6 mm)
A.10 Transponder and Muxponder Card Specifications
This section provides specifications for the TXP_MR_10G, MXP_2.5G_10G, TXP_MR_2.5G, TXPP_MR_2.5G, MXP_MR_2.5G, MXPP_MR_2.5G, MXP_2.5G_10E, MXP_2.5G_10E_C, MXP_2.5G_10EX_C, MXP_2.5G_10E, TXP_MR_10E, TXP_MR_10E_C, TXP_MR_10E_L, TXP_MR_10EX_C, MXP_MR_10DME_C, MXP_MR_10DME_L, MXP_MR_10DMEX_C, 40G-MXP-C, ADM-10G, and OTU2_XP cards.
For compliance information, refer to the Cisco Optical Transport Products Safety and Compliance Information document.
A.10.1 TXP_MR_10G Card Specifications
The TXP_MR_10G card has the following specifications:
•Line (trunk side)
–Bit rate:
9.95328 Gbps for OC-192/STM-64
10.70923 Gbps with ITU-T G.709 Digital Wrapper/forward error correction (FEC)
10.3125 Gbps for 10 Gigabit Ethernet (GE)
11.095 Gbps with ITU-T G.709 Digital Wrapper/FEC over 10 GE
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: 1000 ps/nm
–Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10G card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10G card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10G card.
–Connectors: LC
–Compliance Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.691
•Transmitter (trunk side)
–Maximum transmitter output power: +3.5 dBm
–Minimum transmitter output power: +2.5 dBm
–Transmitter: Lithium Niobate (LN) external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of TXP_MR_10G (16 card versions, each covering two wavelengths):
–1530.33 to 1531.12 nm (two wavelengths)
–1531.90 to 1532.68 nm (two wavelengths)
–1534.25 to 1535.04 nm (two wavelengths)
–1535.82 to 1536.61 nm (two wavelengths)
–1538.19 to 1538.98 nm (two wavelengths)
–1539.77 to 1540.56 nm (two wavelengths)
–1542.14 to 1542.94 nm (two wavelengths)
–1543.73 to 1544.53 nm (two wavelengths)
–1546.12 to 1546.92 nm (two wavelengths)
–1547.72 to 1548.51 nm (two wavelengths)
–1550.12 to 1550.92 nm (two wavelengths)
–1551.72 to 1552.52 nm (two wavelengths)
–1554.13 to 1554.94 nm (two wavelengths)
–1555.75 to 1556.55 nm (two wavelengths)
–1558.17 to 1558.98 nm (two wavelengths)
–1559.79 to 1560.61 nm (two wavelengths)
•Receiver (trunk side):
–Receiver input power (no FEC, unamplified, 23 dB optical signal-to-noise ratio [OSNR], BER 1 * 10 exp - 12): -8 to -21 dBm
–Receiver input power (no FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12): -8 to -19 dBm
–Receiver input power (no FEC, amplified, 19 dB OSNR, BER 1 * 10 exp - 12): -8 to -20 dBm
–Receiver input power (no FEC, amplified, 19 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12):-8 to -18 dBm
–Receiver input power (FEC, unamplified, 23 dB OSNR, BER 8 * 10 exp - 5): -8 to -24 dBm
–Receiver input power (FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm, BER 8 * 10 exp - 5): -8 to -22 dBm
–Receiver input power (FEC, amplified, 9 dB OSNR, BER 8 * 10 exp - 5): -8 to -18 dBm
–Receiver input power (FEC, unamplified, 11 dB OSNR, at +/- 800 ps/nm, BER 8 * 10 exp - 5): -8 to -18 dBm
•Line (client side)
–Bit rate: 9.95328 Gbps or 10.3125 Gbps
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: Compliant with SR-1 specification for OC-192. In the case of 10 GE, the allowance is up to 10 km of single-mode fiber (SMF) dispersion.
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: 1290 to 1330 nm
–Nominal wavelength: 1310 nm
–Transmitter: Distributed feedback (DFB) laser
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: avalanche photodiode (APD)
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.2 MXP_2.5G_10G Card Specifications
The MXP_2.5G_10G card has the following specifications:
•Line (trunk side)
–Bit rate:
9.95328 Gbps for OC-192/STM-64
10.70923 Gbps with ITU-T G.709 Digital Wrapper/FEC
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: 1000 ps/nm
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10G card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10G card. Using direct fiber loopbacks causes irreparable damage to the MXP_2.5G_10G card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +3.5 dBm
–Minimum transmitter output power: +2.5 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of MXP_2.5G_10G (16 card versions, each covering two wavelengths):
–1530.33 to 1531.12 nm (two wavelengths)
–1531.90 to 1532.68 nm (two wavelengths)
–1534.25 to 1535.04 nm (two wavelengths)
–1535.82 to 1536.61 nm (two wavelengths)
–1538.19 to 1538.98 nm (two wavelengths)
–1539.77 to 1540.56 nm (two wavelengths)
–1542.14 to 1542.94 nm (two wavelengths)
–1543.73 to 1544.53 nm (two wavelengths)
–1546.12 to 1546.92 nm (two wavelengths)
–1547.72 to 1548.51 nm (two wavelengths)
–1550.12 to 1550.92 nm (two wavelengths)
–1551.72 to 1552.52 nm (two wavelengths)
–1554.13 to 1554.94 nm (two wavelengths)
–1555.75 to 1556.55 nm (two wavelengths)
–1558.17 to 1558.98 nm (two wavelengths)
–1559.79 to 1560.61 nm (two wavelengths)
•Receiver (trunk side)
–Receiver input power (no FEC, unamplified, 23 dB OSNR, BER 1 * 10 exp - 12): -8 to -21 dBm
–Receiver input power (no FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12): -8 to -19 dBm
–Receiver input power (no FEC, amplified, 19 dB OSNR, BER 1 * 10 exp - 12): -8 to -20 dBm
–Receiver input power (no FEC, amplified, 19 dB OSNR, at +/- 1000 ps/nm BER 1 * 10 exp - 12): -8 to -18 dBm
–Receiver input power (FEC, unamplified, 23 dB OSNR, BER 8 * 10 exp - 5): -8 to -24 dBm
–Receiver input power (FEC, unamplified, 23 dB OSNR, at +/- 1000 ps/nm, BER 8 * 10 exp - 5): -8 to -22 dBm
–Receiver input power (FEC, amplified, 9 dB OSNR, BER 8 * 10 exp - 5): -8 to -18 dBm
–Receiver input power (FEC, unamplified, 11 dB OSNR, at +/- 800 ps/nm, BER 8 * 10 exp - 5): -8 to -18 dBm
•Line (client side)
–Bit rate: 2.48832 Gbps
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: Compliant with SR-1 specification for OC-192. In the case of 10 GE, allowance is up to 10 km of SMF fiber of dispersion.
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side): Depends on the Small Form-factor Pluggable (SFP) that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.3 TXP_MR_2.5G and TXPP_MR_2.5G Card Specifications
The TXP_MR_2.5G and TXPP_MR_2.5G cards have the following specifications:
•Line (trunk side)
–Bit rate:
2.488 Gbps for OC-48/STM-16
2.66 Gbps with ITU-T G.709 Digital Wrapper/FEC
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: 5400 ps/nm
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the TXP_MR_2.5G and TXPP_MR_2.5G cards in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_2.5G and TXPP_MR_2.5G cards. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_2.5G and TXPP_MR_2.5G cards.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +1 dBm
–Minimum transmitter output power: -4.5 dBm
–Transmitter: Direct modulated laser
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths of TXP_MR_2.5G and TXPP_MR_2.5G (eight card versions):
ITU grid blue band: 1530.334 to 1544.526 nm (four card versions covering four wavelengths each)
ITU grid red band: 1546.119 to 1560.606 nm (four card versions covering four wavelengths each)
•Receiver (trunk side, see Table A-34)
Table A-34 TXP_MR_2.5G/TXPP_MR_2.5G Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
Input Power Sensitivity
|
Chromatic Dispersion Tolerance
|
22 dB
|
Off - 2R
|
< 10 exp - 12
|
N/A
|
- 9 to - 24 dBm
|
—
|
22 dB
|
Off - 2R
|
< 10 exp - 12
|
N/A
|
- 9 to - 21 dBm
|
+/- 3300ps/nm
|
21 dB
|
Off - 3R
|
< 10 exp - 12
|
N/A
|
- 9 to - 30 dBm
|
—
|
22 dB
|
Off - 3R
|
< 10 exp - 12
|
N/A
|
- 9 to - 30 dBm
|
+/- 1800ps/nm
|
23 dB
|
Off - 3R
|
< 10 exp - 12
|
N/A
|
- 9 to - 30 dBm
|
+/- 5400ps/nm
|
12 dB
|
Standard- 3R
|
< 10 exp - 5
|
< 10 exp - 15
|
- 9 to - 25 dBm
|
—
|
12 dB
|
Standard- 3R
|
< 10 exp - 5
|
< 10 exp - 15
|
- 9 to - 24 dBm
|
+/- 1800ps/nm
|
12 dB
|
Standard- 3R
|
< 10 exp - 5
|
< 10 exp - 15
|
- 9 to - 23 dBm
|
+/- 5400ps/nm
|
21 dB
|
Standard- 3R
|
< 10 exp - 5
|
< 10 exp - 15
|
- 9 to - 31 dBm
|
—
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
•Line (client side)
–Bit rate: 8 Mbps to 2.488 Gbps
–Code: Scrambled NRZ
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Maximum chromatic dispersion allowance: Based on SFP
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: Based on SFP
–Nominal wavelength: Based on SFP
–Transmitter: Based on SFP
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 850nm to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.4 MXP_MR_2.5G and MXPP_MR_2.5G Card Specifications
The MXP_MR_2.5G and MXPP_MR_2.5G cards have the following specifications:
•Payload configuration
–FC1G—Fibre Channel 1.06 Gbps
–FC2G—Fibre Channel 2.125 Gbps
–FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
–FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
–ESCON—Enterprise System Connection 200 Mbps
–ONE_GE—One Gigabit Ethernet 1.125 Gbps
–Mixed configurations up to maximum line rate of 2.5 Gbps (for example, if you have a port configured for FC2G, you cannot use another port at the same time). See the "MXP_MR_2.5G and MXPP_MR_2.5G Cards" section for more information on mixed-mode operation.
•Client ports: 8x SFP
•Performance monitoring (PM) for all interfaces
•Buffer-to-buffer credit management for distance extension
•Line (trunk side)
–Bit rate: 2.488 Gbps for OC-48/STM-16
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: 6000 ps/nm
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_2.5G and MXPP_MR_2.5G cards in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_2.5G and MXPP_MR_2.5G cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_2.5G and MXPP_MR_2.5G cards.
–Connectors: LC
•Transmitter (trunk side)
–Transmit power: +3 +/- 1 dBm with MXP_MR_2.5G card, and +/- 1 dBm with MXPP_MR_2.5G card
–50-GHz DWDM migration ready (the wavelength deviation is less than +/- 0.040 nm through wavelocker deployment)
–Four-channel wavelength tunability at 100-GHz spacing
–Transmitter maximum return reflectance: -27 dB
–Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
–Minimum side mode suppression ratio: 30 dB
–Transmitter is a direct modulated laser
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths of the TXP_MR_2.5G and TXPP_MR_2.5G cards (eight card versions):
–ITU grid blue band: 1530.334 to 1544.526 nm (four card versions, four wavelengths each)
–ITU grid red band: 1546.119 to 1560.606 nm (four card versions, four wavelengths each)
•Receiver (trunk side, see Table A-35)
Table A-35 MXP_MR_2.5G/MXPP_MR_2.5G Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
Input Power Sensitivity
|
Chromatic Dispersion Tolerance
|
17 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 23 dBm
|
—
|
17 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 22 dBm
|
+/- 1800 ps/nm
|
17 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 21 dBm
|
+/- 5400 ps/nm
|
18 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 23 dBm
|
+/- 1800 ps/nm
|
19 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 23 dBm
|
+/- 5400 ps/nm
|
21 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 30 dBm
|
—
|
21 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 29 dBm
|
+/- 1800 ps/nm
|
21 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 28 dBm
|
+/- 5400 ps/nm
|
22 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 30 dBm
|
+/- 1800 ps/nm
|
23 dB
|
N/A
|
< 10 exp - 12
|
N/A
|
- 9 to - 30 dBm
|
+/- 5400 ps/nm
|
–Receiver sensitivity -28 dBm, BER 1 * 10 exp - 12
–Receiver overload is equal to or exceeds -8 dBm
–Receiver maximum reflectance of -27 dB
•Line (client side)
–Bit rate: 200Mbps or 1.06 Gbps to 2.125 Gbps per client
–Code: Scrambled NRZ
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: Based on SFP
–Nominal wavelength: Based on SFP
–Transmitter: Based on SFP
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm or 850nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 2.25 lb (1.02 kg)
A.10.5 MXP_2.5G_10E Card Specifications
The MXP_2.5G_10E card has the following specifications:
•Line (trunk side)
–Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E card. Using direct fiber loopbacks causes irreparable damage to the MXP_2.5G_10E card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of MXP_2.5G_10E (eight card versions):
ITU grid blue band:
–1530.33 to 1533.07 nm (four channels)
–1534.25 to 1537.00 nm (four channels)
–1538.19 to 1540.95 nm (four channels)
–1542.14 to 1544.92 nm (four channels)
ITU grid red band:
–1546.12 to 1548.92 nm (four channels)
–1550.12 to 1552.93 nm (four channels)
–1554.13 to 1556.96 nm (four channels)
–1558.17 to 1561.01 nm (four channels)
•Receiver (trunk side, see Table A-36)
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
Table A-36 MXP_2.5G_10E Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
30 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 20 dBm
|
+/- 1200 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 20 dBm
|
+/- 1000 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 22 dBm
|
—
|
17 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
15 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
15 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
14 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
•Line (client side)
–Bit rate: 2.5 Gbps per port (OC-48/STM-16)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
–Loopback modes: Terminal and facility
–Connectors: LC (optical)
•Transmitter (client side): Depends on the SFP that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.6 MXP_2.5G_10E_C Card Specifications
The MXP_2.5G_10E_C card has the following specifications:
•Line (trunk side)
–Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E_C card. Using direct fiber loopbacks causes irreparable damage to the card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of MXP_2.5G_10E_C card:
There is a single version of the MXP_2.5G_10E_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-37.
Table A-37 MXP_2.5G_10E_C Card Trunk Wavelengths
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
1
|
196.00
|
1529.55
|
42
|
193.95
|
1545.72
|
2
|
195.95
|
1529.94
|
43
|
193.90
|
1546.119
|
3
|
195.90
|
1530.334
|
44
|
193.85
|
1546.518
|
4
|
195.85
|
1530.725
|
45
|
193.80
|
1546.917
|
5
|
195.80
|
1531.116
|
46
|
193.75
|
1547.316
|
6
|
195.75
|
1531.507
|
47
|
193.70
|
1547.715
|
7
|
195.70
|
1531.898
|
48
|
193.65
|
1548.115
|
8
|
195.65
|
1532.290
|
49
|
193.60
|
1548.515
|
9
|
195.60
|
1532.681
|
50
|
193.55
|
1548.915
|
10
|
195.55
|
1533.073
|
51
|
193.50
|
1549.32
|
11
|
195.50
|
1533.47
|
52
|
193.45
|
1549.71
|
12
|
195.45
|
1533.86
|
53
|
193.40
|
1550.116
|
13
|
195.40
|
1534.250
|
54
|
193.35
|
1550.517
|
14
|
195.35
|
1534.643
|
55
|
193.30
|
1550.918
|
15
|
195.30
|
1535.036
|
56
|
193.25
|
1551.319
|
16
|
195.25
|
1535.429
|
57
|
193.20
|
1551.721
|
17
|
195.20
|
1535.822
|
58
|
193.15
|
1552.122
|
18
|
195.15
|
1536.216
|
59
|
193.10
|
1552.524
|
19
|
195.10
|
1536.609
|
60
|
193.05
|
1552.926
|
20
|
195.05
|
1537.003
|
61
|
193.00
|
1553.33
|
21
|
195.00
|
1537.40
|
62
|
192.95
|
1553.73
|
22
|
194.95
|
1537.79
|
63
|
192.90
|
1554.134
|
23
|
194.90
|
1538.186
|
64
|
192.85
|
1554.537
|
24
|
194.85
|
1538.581
|
65
|
192.80
|
1554.940
|
25
|
194.80
|
1538.976
|
66
|
192.75
|
1555.343
|
26
|
194.75
|
1539.371
|
67
|
192.70
|
1555.747
|
27
|
194.70
|
1539.766
|
68
|
192.65
|
1556.151
|
28
|
194.65
|
1540.162
|
69
|
192.60
|
1556.555
|
29
|
194.60
|
1540.557
|
70
|
192.55
|
1556.959
|
30
|
194.55
|
1540.953
|
71
|
192.50
|
1557.36
|
31
|
194.50
|
1541.35
|
72
|
192.45
|
1557.77
|
32
|
194.45
|
1541.75
|
73
|
192.40
|
1558.173
|
33
|
194.40
|
1542.142
|
74
|
192.35
|
1558.578
|
34
|
194.35
|
1542.539
|
75
|
192.30
|
1558.983
|
35
|
194.30
|
1542.936
|
76
|
192.25
|
1559.389
|
36
|
194.25
|
1543.333
|
77
|
192.20
|
1559.794
|
37
|
194.20
|
1543.730
|
78
|
192.15
|
1560.200
|
38
|
194.15
|
1544.128
|
79
|
192.10
|
1560.606
|
39
|
194.10
|
1544.526
|
80
|
192.05
|
1561.013
|
40
|
194.05
|
1544.924
|
81
|
192.00
|
1561.42
|
41
|
194.00
|
1545.32
|
82
|
191.95
|
1561.83
|
•Receiver (trunk side, see Table A-38)
Table A-38 MXP_2.5G_10E_C Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
30 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 18 dBm
|
+/- 1200 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 18 dBm
|
+/- 1000 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 18 dBm
|
—
|
17 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
15.5 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
14 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
12 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
•Line (client side)
–Bit rate: 2.5 Gbps per port (OC-48/STM-16)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
–Loopback modes: Terminal and facility
–Connectors: LC (optical)
•Transmitter (client side): Depends on the SFP that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.7 MXP_2.5G_10E_L Card Specifications
The MXP_2.5G_10E_L card has the following specifications:
•Line (trunk side)
–Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10E_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10E_L card. Using direct fiber loopbacks causes irreparable damage to the card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of MXP_2.5G_10E_L card:
There is a single version of the MXP_2.5G_10E_L card. It is tunable across 80 wavelengths in the L band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-39.
Table A-39 MXP_2.5G_10E_L Card Trunk Wavelengths
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
1
|
190.85
|
1570.83
|
41
|
188.85
|
1587.46
|
2
|
190.8
|
1571.24
|
42
|
188.8
|
1587.88
|
3
|
190.75
|
1571.65
|
43
|
188.75
|
1588.30
|
4
|
190.7
|
1572.06
|
44
|
188.7
|
1588.73
|
5
|
190.65
|
1572.48
|
45
|
188.65
|
1589.15
|
6
|
190.6
|
1572.89
|
46
|
188.6
|
1589.57
|
7
|
190.55
|
1573.30
|
47
|
188.55
|
1589.99
|
8
|
190.5
|
1573.71
|
48
|
188.5
|
1590.41
|
9
|
190.45
|
1574.13
|
49
|
188.45
|
1590.83
|
10
|
190.4
|
1574.54
|
50
|
188.4
|
1591.26
|
11
|
190.35
|
1574.95
|
51
|
188.35
|
1591.68
|
12
|
190.3
|
1575.37
|
52
|
188.3
|
1592.10
|
13
|
190.25
|
1575.78
|
53
|
188.25
|
1592.52
|
14
|
190.2
|
1576.20
|
54
|
188.2
|
1592.95
|
15
|
190.15
|
1576.61
|
55
|
188.15
|
1593.37
|
16
|
190.1
|
1577.03
|
56
|
188.1
|
1593.79
|
17
|
190.05
|
1577.44
|
57
|
188.05
|
1594.22
|
18
|
190
|
1577.86
|
58
|
188
|
1594.64
|
19
|
189.95
|
1578.27
|
59
|
187.95
|
1595.06
|
20
|
189.9
|
1578.69
|
60
|
187.9
|
1595.49
|
21
|
189.85
|
1579.10
|
61
|
187.85
|
1595.91
|
22
|
189.8
|
1579.52
|
62
|
187.8
|
1596.34
|
23
|
189.75
|
1579.93
|
63
|
187.75
|
1596.76
|
24
|
189.7
|
1580.35
|
64
|
187.7
|
1597.19
|
25
|
189.65
|
1580.77
|
65
|
187.65
|
1597.62
|
26
|
189.6
|
1581.18
|
66
|
187.6
|
1598.04
|
27
|
189.55
|
1581.60
|
67
|
187.55
|
1598.47
|
28
|
189.5
|
1582.02
|
68
|
187.5
|
1598.89
|
29
|
189.45
|
1582.44
|
69
|
187.45
|
1599.32
|
30
|
189.4
|
1582.85
|
70
|
187.4
|
1599.75
|
31
|
189.35
|
1583.27
|
71
|
187.35
|
1600.17
|
32
|
189.3
|
1583.69
|
72
|
187.3
|
1600.60
|
33
|
189.25
|
1584.11
|
73
|
187.25
|
1601.03
|
34
|
189.2
|
1584.53
|
74
|
187.2
|
1601.46
|
35
|
189.15
|
1584.95
|
75
|
187.15
|
1601.88
|
36
|
189.1
|
1585.36
|
76
|
187.1
|
1602.31
|
37
|
189.05
|
1585.78
|
77
|
187.05
|
1602.74
|
38
|
189
|
1586.20
|
78
|
187
|
1603.17
|
39
|
188.95
|
1586.62
|
79
|
186.95
|
1603.60
|
40
|
188.9
|
1587.04
|
80
|
186.9
|
1604.03
|
•Receiver (trunk side, see Table A-40)
Table A-40 MXP_2.5G_10E_L Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
30 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 20 dBm
|
+/- 1200 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 20 dBm
|
+/- 1000 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 22 dBm
|
—
|
17 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
15.5 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
15 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
13 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1570 to 1604 nm
•Line (client side)
–Bit rate: 2.5 Gbps per port (OC-48/STM-16)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
–Loopback modes: Terminal and facility
–Connectors: LC (optical)
•Transmitter (client side): Depends on the SFP that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.8 MXP_2.5G_10EX_C Card Specifications
The MXP_2.5G_10EX_C card has the following specifications:
•Line (trunk side)
–Bit rate: 10.70923 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1600 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_2.5G_10EX_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_2.5G_10EX_C card. Using direct fiber loopbacks causes irreparable damage to the card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of MXP_2.5G_10EX_C card:
There is a single version of the MXP_2.5G_10EX_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-37.
Table A-41 MXP_2.5G_10EX_C Card Trunk Wavelengths
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
1
|
196.00
|
1529.55
|
42
|
193.95
|
1545.72
|
2
|
195.95
|
1529.94
|
43
|
193.90
|
1546.12
|
3
|
195.90
|
1530.334
|
44
|
193.85
|
1546.52
|
4
|
195.85
|
1530.725
|
45
|
193.80
|
1546.92
|
5
|
195.80
|
1531.116
|
46
|
193.75
|
1547.32
|
6
|
195.75
|
1531.507
|
47
|
193.70
|
1547.72
|
7
|
195.70
|
1531.898
|
48
|
193.65
|
1548.11
|
8
|
195.65
|
1532.290
|
49
|
193.60
|
1548.51
|
9
|
195.60
|
1532.681
|
50
|
193.55
|
1548.91
|
10
|
195.55
|
1533.073
|
51
|
193.50
|
1549.32
|
11
|
195.50
|
1533.47
|
52
|
193.45
|
1549.72
|
12
|
195.45
|
1533.86
|
53
|
193.40
|
1550.12
|
13
|
195.40
|
1534.250
|
54
|
193.35
|
1550.52
|
14
|
195.35
|
1534.643
|
55
|
193.30
|
1550.92
|
15
|
195.30
|
1535.036
|
56
|
193.25
|
1551.32
|
16
|
195.25
|
1535.429
|
57
|
193.20
|
1551.72
|
17
|
195.20
|
1535.822
|
58
|
193.15
|
1552.12
|
18
|
195.15
|
1536.216
|
59
|
193.10
|
1552.52
|
19
|
195.10
|
1536.609
|
60
|
193.05
|
1552.93
|
20
|
195.05
|
1537.003
|
61
|
193.00
|
1553.33
|
21
|
195.00
|
1537.40
|
62
|
192.95
|
1553.73
|
22
|
194.95
|
1537.79
|
63
|
192.90
|
1554.13
|
23
|
194.90
|
1538.186
|
64
|
192.85
|
1554.54
|
24
|
194.85
|
1538.581
|
65
|
192.80
|
1554.94
|
25
|
194.80
|
1538.976
|
66
|
192.75
|
1555.34
|
26
|
194.75
|
1539.371
|
67
|
192.70
|
1555.75
|
27
|
194.70
|
1539.766
|
68
|
192.65
|
1556.15
|
28
|
194.65
|
1540.162
|
69
|
192.60
|
1556.55
|
29
|
194.60
|
1540.557
|
70
|
192.55
|
1556.96
|
30
|
194.55
|
1540.953
|
71
|
192.50
|
1557.36
|
31
|
194.50
|
1541.35
|
72
|
192.45
|
1557.77
|
32
|
194.45
|
1541.75
|
73
|
192.40
|
1558.17
|
33
|
194.40
|
1542.142
|
74
|
192.35
|
1558.58
|
34
|
194.35
|
1542.539
|
75
|
192.30
|
1558.98
|
35
|
194.30
|
1542.936
|
76
|
192.25
|
1559.39
|
36
|
194.25
|
1543.333
|
77
|
192.20
|
1559.79
|
37
|
194.20
|
1543.730
|
78
|
192.15
|
1560.20
|
38
|
194.15
|
1544.128
|
79
|
192.10
|
1560.61
|
39
|
194.10
|
1544.526
|
80
|
192.05
|
1561.01
|
40
|
194.05
|
1544.924
|
81
|
192.00
|
1561.42
|
41
|
194.00
|
1545.32
|
82
|
191.95
|
1561.83
|
•Receiver (trunk side, see Table A-42)
Table A-42 TMXP_2.5G_10EX_C Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
PMD tolerance
|
16 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
+/- 1600 ps/nm
|
—
|
15 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
—
|
—
|
TBD
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
—
|
3
|
12.5 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
—
|
—
|
17 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
+/- 4000 ps/nm
|
—
|
15.2 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
+/- 2500 ps/nm
|
—
|
17.4 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
|
3
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
•Line (client side)
–Bit rate: 2.5 Gbps per port (OC-48/STM-16)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
–Loopback modes: Terminal and facility
–Connectors: LC (optical)
•Transmitter (client side): Depends on the SFP that is used.
•Receiver (client side): Depends on the SFP that is used.
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.9 MXP_MR_10DME_C Card Specifications
The MXP_MR_10DME_C card has the following specifications:
•Payload configuration
–FC1G—Fibre Channel 1.06 Gbps
–FC2G—Fibre Channel 2.125 Gbps
–FC4G—Fibre Channel 4.25 Gbps
–FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
–FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
–FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)
–ISC compatibility
–ISC peer 1G
–ISC peer 2G
–ONE_GE—One Gigabit Ethernet 1.125 Gbps
–Mixed configurations up to maximum line rate of 10.0 Gbps. See the "MXP_MR_10DME_C and MXP_MR_10DME_L Cards" section for more information on mixed-mode operation.
•Client ports: 8x SFP
•Line (trunk side)
–Bit rate: 9.952 Gbps for OC-192/STM-64
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DME_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DME_C cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DME_C cards.
–Connectors: LC
•Transmitter (trunk side)
–Minimum output power: +3 dBm
–Maximum output power: +6 dBm
–Minimum Single-Mode Suppression Ratio (SMSR): 30 dB
–Minimum optical extinction ratio: 10 dB
–41 wavelength tunability at 100-GHz spacing
–Receiver maximum return reflectance (Rx return loss): -27 dB
–Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
–Minimum side mode suppression ratio: 30 dB
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
–For available wavelengths for the MXP_MR_10DME_C card, see Table 10-29.
•For the receiver trunk side, see Table A-43:
Table A-43 MXP_MR_10DME_C Card Receiver Trunk Side Specifications
FEC Applications
|
|
Pre-FEC BER
|
Post-FEC BER
|
Input Power Sensitivity
|
Chromatic Dispersion Tolerance
|
Power Penalty
|
OSNR Penalty
|
None
|
23 dB
|
< 10 exp - 12
|
—
|
-8 to -20 dBm
|
+/- 1200 ps/nm
|
2 dBm
|
—
|
19 dB
|
< 10 exp - 12
|
—
|
-9 to -22 dBm
|
+/- 1000 ps/nm
|
2 dBm
|
—
|
FEC
|
10 dB
|
< 10 exp - 5
|
< 10 exp - 15
|
-8 to -18 dBm
|
+/- 800 ps/nm
|
—
|
1.5 dB
|
Enhanced FEC
|
19 dB
|
< 10 exp - 4
|
< 10 exp - 15
|
-8 to -26 dBm
|
+/- 800 ps/nm
|
2 dBm
|
2 dB
|
8 dB
|
< 10 exp - 4
|
< 10 exp - 15
|
-8 to -18 dBm
|
+/- 800 ps/nm
|
2 dBm
|
1.5 dB
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
•Line (client side)
–Bit rate: 1.06 Gbps to 4.25 Gbps per client
–Code: Scrambled NRZ
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Maximum chromatic dispersion allowance: Based on SFP
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: Based on SFP
–Nominal wavelength: Based on SFP
–Transmitter: Based on SFP
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm or 850nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 2.25 lb (1.02 kg)
A.10.10 MXP_MR_10DME_L Card Specifications
The MXP_MR_10DME_L card has the following specifications:
•Payload configuration
–FC1G—Fibre Channel 1.06 Gbps
–FC2G—Fibre Channel 2.125 Gbps
–FC4G—Fibre Channel 4.25 Gbps
–FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
–FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
–FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)
–ISC compatibility
–ISC peer 1G
–ISC peer 2G
–ONE_GE—One Gigabit Ethernet 1.125 Gbps
–Mixed configurations up to maximum line rate of 10.0 Gbps. See the "MXP_MR_10DME_C and MXP_MR_10DME_L Cards" section for more information on mixed-mode operation.
•Client ports: 8x SFP
•Line (trunk side)
–Bit rate: 9.952 Gbps for OC-192/STM-64
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DME_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DME_L cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DME_L cards.
–Connectors: LC
•Transmitter (trunk side)
–Minimum output power: +3 dBm
–Maximum output power: +6 dBm
–Minimum SMSR: 30 dB
–Minimum optical extinction ratio: 10.5 dB
–40 wavelength tunability at 100-GHz spacing, 80 wavelength tunability at 50-GHz spacing
–Receiver maximum return reflectance (Rx return loss): -27 dB
–Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
–Minimum side mode suppression ratio: 30 dB
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
–For the currently available wavelengths for the MXP_MR_10DME_L card, see Table 10-30.
•Table A-44 provides the receiver trunk side specifications:
Table A-44 MXP_MR_10DME_L Card Receiver Trunk Side Specifications
FEC Applications
|
|
Pre-FEC BER
|
Post-FEC BER
|
Input Power Sensitivity
|
Chromatic Dispersion Tolerance
|
Power Penalty
|
OSNR Penalty
|
None
|
23 dB
|
< 10 exp - 12
|
—
|
-8 to -19 dBm
|
+/- 1200 ps/nm
|
2 dBm
|
—
|
19 dB
|
< 10 exp - 12
|
—
|
-9 to -19 dBm
|
+/- 1000 ps/nm
|
2 dBm
|
—
|
FEC
|
10 dB
|
< 10 exp - 5
|
< 10 exp - 15
|
-8 to -18 dBm
|
+/- 800 ps/nm
|
—
|
1.5 dB
|
Enhanced FEC
|
19 dB
|
< 10 exp - 4
|
< 10 exp - 15
|
-8 to -26 dBm
|
+/- 800 ps/nm
|
—
|
2 dB
|
8 dB
|
< 10 exp - 4
|
< 10 exp - 15
|
-8 to -18 dBm
|
+/- 800 ps/nm
|
—
|
1.5 dB
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1570 to 1604 nm
•Line (client side)
–Bit rate: 1.06 Gbps to 4.25 Gbps per client
–Code: Scrambled NRZ
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Maximum chromatic dispersion allowance: Based on SFP
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: Based on SFP
–Nominal wavelength: Based on SFP
–Transmitter: Based on SFP
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm or 850nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 2.25 lb (1.02 kg)
A.10.11 MXP_MR_10DMEX_C Card Specifications
The MXP_MR_10DMEX_C card has the following specifications:
•Payload configuration
–FC1G—Fibre Channel 1.06 Gbps
–FC2G—Fibre Channel 2.125 Gbps
–FC4G—Fibre Channel 4.25 Gbps
–FICON1G—Fiber connectivity 1.06 Gbps (IBM signal)
–FICON2G—Fiber connectivity 2.125 Gbps (IBM signal)
–FICON4G—Fiber connectivity 4.25 Gbps (IBM signal)
–ISC compatibility
–ISC peer 1G
–ISC peer 2G
–ONE_GE—One Gigabit Ethernet 1.125 Gbps
–Mixed configurations up to maximum line rate of 10.0 Gbps.
•Client ports: 8x SFP
•Line (trunk side)
–Bit rate: 9.952 Gbps for OC-192/STM-64
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the MXP_MR_10DMEX_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the MXP_MR_10DMEX_C cards. Using direct fiber loopbacks causes irreparable damage to the MXP_MR_10DMEX_C cards.
–Connectors: LC
•Transmitter (trunk side)
–Minimum output power: +3 dBm
–Maximum output power: +7 dBm
–Minimum Single-Mode Suppression Ratio (SMSR): 30 dB
–Minimum optical extinction ratio: 10 dB
–41 wavelength tunability at 100-GHz spacing
–Receiver maximum return reflectance (Rx return loss): -27 dB
–Chromatic dispersion allowance: 5400 ps/nm, giving an optical power penalty < 2.0 dB
–Minimum side mode suppression ratio: 30 dB
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
–For available wavelengths for the MXP_MR_10DMEX_C card, see Table 10-29.
•For the receiver trunk side, see Table A-45:
Table A-45 MXP_MR_10DMEX_C Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
PMD tolerance
|
16 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
+/- 1600 ps/nm
|
—
|
15 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
—
|
—
|
TBD
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
—
|
3
|
12.5 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
—
|
—
|
17 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
+/- 4000 ps/nm
|
—
|
15.2 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
+/- 2500 ps/nm
|
—
|
17.4 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
|
3
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
•Line (client side)
–Bit rate: 1.06 Gbps to 4.25 Gbps per client
–Code: Scrambled NRZ
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Maximum chromatic dispersion allowance: Based on SFP
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: Based on SFP
–Nominal wavelength: Based on SFP
–Transmitter: Based on SFP
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm or 850nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 2.25 lb (1.02 kg)
A.10.12 TXP_MR_10E Card Specifications
The TXP_MR_10E card has the following specifications:
•Line (trunk side)
–Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm for C-band and +2 dBm for L-band
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of TXP_MR_10E:
C-band frequency plan (eight card versions, each with four tunable channels on the ITU 100-GHz grid):
–1530.33 to 1533.07 nm (four channels)
–1534.25 to 1537.00 nm (four channels)
–1538.19 to 1540.95 nm (four channels)
–1542.14 to 1544.92 nm (four channels)
–1546.12 to 1548.92 nm (four channels)
–1550.12 to 1552.93 nm (four channels)
–1554.13 to 1556.96 nm (four channels)
–1558.17 to 1561.01 nm (four channels)
L-band frequency plan (five card versions, each with eight tunable channels on the ITU 50-GHz grid):
–1577.44 to 1580.35 nm (eight channels)
–1580.77 to 1583.69 nm (eight channels)
–1584.11 to 1587.04 nm (eight channels)
–1587.46 to 1590.41 nm (eight channels)
–1590.83 to 1593.79 nm (eight channels)
•Receiver (trunk side, see Table A-46)
Table A-46 TXP_MR_10E Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
30 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 20 dBm
|
+/- 1200 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 20 dBm
|
+ - 1000 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 22 dBm
|
—
|
17 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
15 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
15 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
14 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
•Line (client side):
–10-Gigabit Small Form-factor Pluggable (XFP)-based SR
–Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 6.6 ps/nm
–Loopback modes: Terminal and facility
–Connectors: LC
–Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, ITU-T G.691
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: 1290 to 1330 nm
–Nominal wavelength: 1310 nm
–Transmitter: DFB laser
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.13 TXP_MR_10E_C Card Specifications
The TXP_MR_10E_C card has the following specifications:
•Line (trunk side)
–Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E_C card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E_C card.
–Connectors: LC
–Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, and ITU-T G.709
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of TXP_MR_10E_C card:
There is a single version of the TXP_MR_10E_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-47.
Table A-47 TXP_MR_10E_C Card Trunk Wavelengths
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
1
|
196.00
|
1529.55
|
42
|
193.95
|
1545.72
|
2
|
195.95
|
1529.94
|
43
|
193.90
|
1546.119
|
3
|
195.90
|
1530.334
|
44
|
193.85
|
1546.518
|
4
|
195.85
|
1530.725
|
45
|
193.80
|
1546.917
|
5
|
195.80
|
1531.116
|
46
|
193.75
|
1547.316
|
6
|
195.75
|
1531.507
|
47
|
193.70
|
1547.715
|
7
|
195.70
|
1531.898
|
48
|
193.65
|
1548.115
|
8
|
195.65
|
1532.290
|
49
|
193.60
|
1548.515
|
9
|
195.60
|
1532.681
|
50
|
193.55
|
1548.915
|
10
|
195.55
|
1533.073
|
51
|
193.50
|
1549.32
|
11
|
195.50
|
1533.47
|
52
|
193.45
|
1549.71
|
12
|
195.45
|
1533.86
|
53
|
193.40
|
1550.116
|
13
|
195.40
|
1534.250
|
54
|
193.35
|
1550.517
|
14
|
195.35
|
1534.643
|
55
|
193.30
|
1550.918
|
15
|
195.30
|
1535.036
|
56
|
193.25
|
1551.319
|
16
|
195.25
|
1535.429
|
57
|
193.20
|
1551.721
|
17
|
195.20
|
1535.822
|
58
|
193.15
|
1552.122
|
18
|
195.15
|
1536.216
|
59
|
193.10
|
1552.524
|
19
|
195.10
|
1536.609
|
60
|
193.05
|
1552.926
|
20
|
195.05
|
1537.003
|
61
|
193.00
|
1553.33
|
21
|
195.00
|
1537.40
|
62
|
192.95
|
1553.73
|
22
|
194.95
|
1537.79
|
63
|
192.90
|
1554.134
|
23
|
194.90
|
1538.186
|
64
|
192.85
|
1554.537
|
24
|
194.85
|
1538.581
|
65
|
192.80
|
1554.940
|
25
|
194.80
|
1538.976
|
66
|
192.75
|
1555.343
|
26
|
194.75
|
1539.371
|
67
|
192.70
|
1555.747
|
27
|
194.70
|
1539.766
|
68
|
192.65
|
1556.151
|
28
|
194.65
|
1540.162
|
69
|
192.60
|
1556.555
|
29
|
194.60
|
1540.557
|
70
|
192.55
|
1556.959
|
30
|
194.55
|
1540.953
|
71
|
192.50
|
1557.36
|
31
|
194.50
|
1541.35
|
72
|
192.45
|
1557.77
|
32
|
194.45
|
1541.75
|
73
|
192.40
|
1558.173
|
33
|
194.40
|
1542.142
|
74
|
192.35
|
1558.578
|
34
|
194.35
|
1542.539
|
75
|
192.30
|
1558.983
|
35
|
194.30
|
1542.936
|
76
|
192.25
|
1559.389
|
36
|
194.25
|
1543.333
|
77
|
192.20
|
1559.794
|
37
|
194.20
|
1543.730
|
78
|
192.15
|
1560.200
|
38
|
194.15
|
1544.128
|
79
|
192.10
|
1560.606
|
39
|
194.10
|
1544.526
|
80
|
192.05
|
1561.013
|
40
|
194.05
|
1544.924
|
81
|
192.00
|
1561.42
|
41
|
194.00
|
1545.32
|
82
|
191.95
|
1561.83
|
•Receiver (trunk side, see Table A-48)
Table A-48 TXP_MR_10E _C Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
30 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 18 dBm
|
+/- 1200 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 18 dBm
|
+ - 1000 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 18 dBm
|
—
|
17 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
15.5 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
14 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
12 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
•Line (client side):
–XFP-based SR
–Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 6.6 ps/nm
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: 1290 to 1330 nm
–Nominal wavelength: 1310 nm
–Transmitter: DFB laser
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.14 TXP_MR_10E_L Card Specifications
The TXP_MR_10E_L card has the following specifications:
•Line (trunk side)
–Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1200 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10E_L card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10E_L card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10E_L card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +2 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of TXP_MR_10E_L card:
There is a single version of the TXP_MR_10E_L card. It is tunable across 80 wavelengths in the L band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-49.
Table A-49 TXP_MR_10E_L Card Trunk Wavelengths
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
1
|
190.85
|
1570.83
|
41
|
188.85
|
1587.46
|
2
|
190.8
|
1571.24
|
42
|
188.8
|
1587.88
|
3
|
190.75
|
1571.65
|
43
|
188.75
|
1588.30
|
4
|
190.7
|
1572.06
|
44
|
188.7
|
1588.73
|
5
|
190.65
|
1572.48
|
45
|
188.65
|
1589.15
|
6
|
190.6
|
1572.89
|
46
|
188.6
|
1589.57
|
7
|
190.55
|
1573.30
|
47
|
188.55
|
1589.99
|
8
|
190.5
|
1573.71
|
48
|
188.5
|
1590.41
|
9
|
190.45
|
1574.13
|
49
|
188.45
|
1590.83
|
10
|
190.4
|
1574.54
|
50
|
188.4
|
1591.26
|
11
|
190.35
|
1574.95
|
51
|
188.35
|
1591.68
|
12
|
190.3
|
1575.37
|
52
|
188.3
|
1592.10
|
13
|
190.25
|
1575.78
|
53
|
188.25
|
1592.52
|
14
|
190.2
|
1576.20
|
54
|
188.2
|
1592.95
|
15
|
190.15
|
1576.61
|
55
|
188.15
|
1593.37
|
16
|
190.1
|
1577.03
|
56
|
188.1
|
1593.79
|
17
|
190.05
|
1577.44
|
57
|
188.05
|
1594.22
|
18
|
190
|
1577.86
|
58
|
188
|
1594.64
|
19
|
189.95
|
1578.27
|
59
|
187.95
|
1595.06
|
20
|
189.9
|
1578.69
|
60
|
187.9
|
1595.49
|
21
|
189.85
|
1579.10
|
61
|
187.85
|
1595.91
|
22
|
189.8
|
1579.52
|
62
|
187.8
|
1596.34
|
23
|
189.75
|
1579.93
|
63
|
187.75
|
1596.76
|
24
|
189.7
|
1580.35
|
64
|
187.7
|
1597.19
|
25
|
189.65
|
1580.77
|
65
|
187.65
|
1597.62
|
26
|
189.6
|
1581.18
|
66
|
187.6
|
1598.04
|
27
|
189.55
|
1581.60
|
67
|
187.55
|
1598.47
|
28
|
189.5
|
1582.02
|
68
|
187.5
|
1598.89
|
29
|
189.45
|
1582.44
|
69
|
187.45
|
1599.32
|
30
|
189.4
|
1582.85
|
70
|
187.4
|
1599.75
|
31
|
189.35
|
1583.27
|
71
|
187.35
|
1600.17
|
32
|
189.3
|
1583.69
|
72
|
187.3
|
1600.60
|
33
|
189.25
|
1584.11
|
73
|
187.25
|
1601.03
|
34
|
189.2
|
1584.53
|
74
|
187.2
|
1601.46
|
35
|
189.15
|
1584.95
|
75
|
187.15
|
1601.88
|
36
|
189.1
|
1585.36
|
76
|
187.1
|
1602.31
|
37
|
189.05
|
1585.78
|
77
|
187.05
|
1602.74
|
38
|
189
|
1586.20
|
78
|
187
|
1603.17
|
39
|
188.95
|
1586.62
|
79
|
186.95
|
1603.60
|
40
|
188.9
|
1587.04
|
80
|
186.9
|
1604.03
|
•Receiver (trunk side, see Table A-50)
Table A-50 TXP_MR_10E Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
30 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 20 dBm
|
+/- 1200 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 20 dBm
|
+ - 1000 ps/nm
|
26 dB
|
Off
|
< 10 exp - 12
|
N/A
|
- 8 to - 22 dBm
|
—
|
17 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
15.5 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
15 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
+/- 800 ps/nm
|
13 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 18 dBm
|
—
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1570 to 1604 nm
•Line (client side):
–XFP-based SR
–Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 6.6 ps/nm
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: 1290 to 1330 nm
–Nominal wavelength: 1310 nm
–Transmitter: DFB laser
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.15 TXP_MR_10EX_C Card Specifications
The TXP_MR_10EX_C card has the following specifications:
•Line (trunk side)
–Bit rate: OC-192/STM-64 (9.95328 Gbps), OTU2 (10.70923 Gbps), 10GE (10.3125 Gbps), 10GE into OTU2 (non-standard 11.0957 Gbps), 10G FC (10.51875 Gbps), or 10G FC into OTU2 (non-standard 11.31764 Gbps)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: +/- 1600 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
Caution You must use a 15-dB fiber attenuator (10 to 20 dB) when working with the TXP_MR_10EX_C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the TXP_MR_10EX_C card. Using direct fiber loopbacks causes irreparable damage to the TXP_MR_10EX_C card.
–Connectors: LC
–Compliance: Telcordia GR-253-CORE, ITU-T G.707, ITU-T G.957, and ITU-T G.709
•Transmitter (trunk side)
–Maximum transmitter output power: +6 dBm
–Minimum transmitter output power: +3 dBm
–Transmitter: LN external modulator transmitter
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of TXP_MR_10EX_C card:
There is a single version of the TXP_MR_10EX_C card. It is tunable across 82 wavelengths in the C-band frequency plan, with channels on the ITU 50-GHz grid, as shown in Table A-51.
Table A-51 TXP_MR_10EX_C Card Trunk Wavelengths
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
Channel Number
|
Frequency (THz)
|
Wavelength (nm)
|
1
|
196.00
|
1529.55
|
42
|
193.95
|
1545.72
|
2
|
195.95
|
1529.94
|
43
|
193.90
|
1546.12
|
3
|
195.90
|
1530.334
|
44
|
193.85
|
1546.52
|
4
|
195.85
|
1530.725
|
45
|
193.80
|
1546.92
|
5
|
195.80
|
1531.116
|
46
|
193.75
|
1547.32
|
6
|
195.75
|
1531.507
|
47
|
193.70
|
1547.72
|
7
|
195.70
|
1531.898
|
48
|
193.65
|
1548.11
|
8
|
195.65
|
1532.290
|
49
|
193.60
|
1548.51
|
9
|
195.60
|
1532.681
|
50
|
193.55
|
1548.91
|
10
|
195.55
|
1533.073
|
51
|
193.50
|
1549.32
|
11
|
195.50
|
1533.47
|
52
|
193.45
|
1549.72
|
12
|
195.45
|
1533.86
|
53
|
193.40
|
1550.12
|
13
|
195.40
|
1534.250
|
54
|
193.35
|
1550.52
|
14
|
195.35
|
1534.643
|
55
|
193.30
|
1550.92
|
15
|
195.30
|
1535.036
|
56
|
193.25
|
1551.32
|
16
|
195.25
|
1535.429
|
57
|
193.20
|
1551.72
|
17
|
195.20
|
1535.822
|
58
|
193.15
|
1552.12
|
18
|
195.15
|
1536.216
|
59
|
193.10
|
1552.52
|
19
|
195.10
|
1536.609
|
60
|
193.05
|
1552.93
|
20
|
195.05
|
1537.003
|
61
|
193.00
|
1553.33
|
21
|
195.00
|
1537.40
|
62
|
192.95
|
1553.73
|
22
|
194.95
|
1537.79
|
63
|
192.90
|
1554.13
|
23
|
194.90
|
1538.186
|
64
|
192.85
|
1554.54
|
24
|
194.85
|
1538.581
|
65
|
192.80
|
1554.94
|
25
|
194.80
|
1538.976
|
66
|
192.75
|
1555.34
|
26
|
194.75
|
1539.371
|
67
|
192.70
|
1555.75
|
27
|
194.70
|
1539.766
|
68
|
192.65
|
1556.15
|
28
|
194.65
|
1540.162
|
69
|
192.60
|
1556.55
|
29
|
194.60
|
1540.557
|
70
|
192.55
|
1556.96
|
30
|
194.55
|
1540.953
|
71
|
192.50
|
1557.36
|
31
|
194.50
|
1541.35
|
72
|
192.45
|
1557.77
|
32
|
194.45
|
1541.75
|
73
|
192.40
|
1558.17
|
33
|
194.40
|
1542.142
|
74
|
192.35
|
1558.58
|
34
|
194.35
|
1542.539
|
75
|
192.30
|
1558.98
|
35
|
194.30
|
1542.936
|
76
|
192.25
|
1559.39
|
36
|
194.25
|
1543.333
|
77
|
192.20
|
1559.79
|
37
|
194.20
|
1543.730
|
78
|
192.15
|
1560.20
|
38
|
194.15
|
1544.128
|
79
|
192.10
|
1560.61
|
39
|
194.10
|
1544.526
|
80
|
192.05
|
1561.01
|
40
|
194.05
|
1544.924
|
81
|
192.00
|
1561.42
|
41
|
194.00
|
1545.32
|
82
|
191.95
|
1561.83
|
•Receiver (trunk side, see Table A-48)
Table A-52 TXP_MR_10E _C Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
PMD tolerance
|
16 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
+/- 1600 ps/nm
|
—
|
15 dB
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
—
|
—
|
TBD
|
Standard
|
< 10 exp - 5
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
—
|
3
|
12.5 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
—
|
—
|
17 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
+/- 4000 ps/nm
|
—
|
15.2 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
+/- 2500 ps/nm
|
—
|
17.4 dB
|
Enhanced
|
< 7 x 10 exp - 4
|
< 10 exp - 15
|
- 8 to - 20 dBm
|
|
3
|
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
•Line (client side):
–XFP-based SR
–Bit rate: 10GE (10.3125 Gbps), 10G FC (10.51875 Gbps), or STM-64/OC-192
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode
–Maximum chromatic dispersion allowance: 6.6 ps/nm
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: -1 dBm
–Minimum transmitter output power: -6 dBm
–Center wavelength: 1290 to 1330 nm
–Nominal wavelength: 1310 nm
–Transmitter: DFB laser
•Receiver (client side)
–Maximum receiver level: -1 dBm at BER 1 * 10 exp - 12
–Minimum receiver level: -14 dBm at BER 1 * 10 exp - 12
–Receiver: APD
–Link loss budget: 8 dB minimum, at BER = 1 * 10 exp - 12
–Receiver input wavelength range: 1290 to 1605 nm
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 3.1 lb (1.3 kg)
A.10.16 40G-MXP-C Card Specifications
The 40G-MXP-C card has the following specifications:
•Payload configuration
–FC8G—Fibre Channel 8.50 Gbps
–FC10G—Fiber Channel 10.519 Gbps
–FICON10G—Fiber connectivity 10.519 Gbps
–OC192/STM64/10GE WAN-Phy—9.953 Gbps
–10-GE LAN-Phy—10.312 Gbps
–OTU2 (OC192/STM64/10GE WAN-Phy)—10.709 Gbps
–OTU2e (10GE LAN-Phy)—11.096 Gbps
•Client ports: 4 X SFP
•Line (trunk side)
–Bit rate: 43.018 Gbps for OTU3, 44.57 Gbps for OTU3e
–Code: RZ-DQPSK 40G
–Fiber: 1550-nm single-mode
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the 40G-MXP-C card in a loopback on the trunk port. Do not use direct fiber loopbacks with the 40G-MXP-C cards. Using direct fiber loopbacks causes irreparable damage to the 40G-MXP-C cards.
–Connectors: LC
•Transmitter (trunk side)
–Minimum output power: -2 dBm
–Maximum output power: +2 dBm
–Minimum Single-Mode Suppression Ratio (SMSR): 35 dB
–Minimum optical extinction ratio: 25 dB
–Wavelength tunability (total 82 wavelengths) at 50-GHz spacing
–Receiver maximum return reflectance (Rx return loss): -27 dB
–Chromatic dispersion allowance: 750 ps/nm, giving an optical OSNR penalty < 2.0 dB
–Minimum side mode suppression ratio: 30 dB
–Wavelength stability (drift): +/- 25 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
–For wavelengths available for the 40G-MXP-C card, see Table 10-29.
•Receiver (trunk side)
–Receiver: PIN
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
–Receiver input wavelength range: 1529 to 1562 nm
Table A-53 lists the trunk side specifications of the receiver.
Table A-53 40G-MXP-C Card Receiver (Trunk) Side Specifications
FEC Applications
|
|
Pre-FEC BER
|
Post-FEC BER
|
Input Power Sensitivity
|
Chromatic Dispersion Tolerance
|
Power Penalty
|
OSNR Penalty
|
FEC
|
12 dB
|
< 10 exp - 5
|
< 10 exp - 15
|
-8 to -20 dBm
|
+/- 750 ps/nm
|
—
|
2 dB
|
Enhanced FEC
|
19 dB
|
< 10 exp - 3
|
< 10 exp - 15
|
-8 to -24 dBm
|
+/- 750 ps/nm
|
2 dBm
|
—
|
8 dB
|
< 10 exp - 3
|
< 10 exp - 15
|
-8 to -20 dBm
|
+/- 750 ps/nm
|
—
|
2 dB
|
•Line (client side)
–Bit rate: 8.50 Gbps to 11.096 Gbps per client
–Code: NRZ 40G
–Fiber: Based on SFP (1310-nm single-mode or 850-nm multimode)
–Maximum chromatic dispersion allowance: Based on XFP
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (client side)
–Maximum transmitter output power: Based on XFP
–Minimum transmitter output power: Based on XFP
–Center wavelength: Based on XFP
–Nominal wavelength: Based on XFP
–Transmitter: Based on XFP
•Receiver (client side)
–Maximum receiver level: Based on XFP
–Minimum receiver level: Based on XFP
–Receiver: Based on XFP
–Link loss budget: Based on XFP
–Receiver input wavelength range: Based on XFP
•Environmental Exception
–Short term ambient temperature: Functionality is guaranteed, according to GR-63 Issue 3 for the thermal cycles except for the temperature values which are -5 to 45 degrees Celsius (23 to 113 degrees Fahrenheit) instead of -5 to 55 degrees Celsius (23 to 131 degrees Fahrenheit).
•Dimensions
–Height: 12.650 in. (321.3 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.000 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight excluding clam shell: 7.7 lb (3.5 kg)
A.10.17 ADM-10G Card Specifications
The ADM-10G card has the following specifications:
•Line
–Bit rate: OC-3/STM-1 (155.520 Mb/s); OC-12/STM-3 (622.08 Mb/s); OC-48/STM-16 (2488.32 Mb/s); OC-192/STM-64 (9.95328 Gbps)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode for ONS-XC-10GS1 XFP or 1530.33 to 1554.94-nm single-mode for ONS-XC-10G-xx.x XFP
–Maximum chromatic dispersion allowance: up to 3600 ps/nm
–Loopback modes: Terminal, facility, and cross-connect
–Connectors: LC
•Transmitter (trunk side)
–Transmitter: LN external modulator transmitter
–Maximum transmitter output power: Depends on XFP that is used
–Minimum transmitter output power: Depends on XFP that is used
–Wavelength stability (drift): +/- 25 picometers (pm)
•Receiver (trunk side)
–Receiver: APD
–Receiver input wavelength range: Depends on XFP that is used
–Receiver sensitivity: depends on XFP that is used
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
•Dimensions
–Height: 12.65 in. (321.3 mm)
–Width: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.00 in. (228.6 mm)
–Depth with backplane connector: 9.250 in. (235 mm)
–Weight not including clam shell: 5.07 lb (2.3 kg)
A.10.18 GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE Card Specifications
The GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE cards have the following specifications:
•Line (trunk side)
–Bit rate: 11.1 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode) or 10.3125 Gbps (in ITU-T G.709 Digital Wrapper/FEC mode disabled)
–Code: Scrambled NRZ
–Fiber: 1550-nm single-mode
–Maximum chromatic dispersion allowance: - 500 to 1600 ps/nm (specified penalty)
–Loopback modes: Terminal and facility
Caution You must use a 20-dB fiber attenuator (15 to 25 dB) when working with the GE_XP and GE_XPE card in a loopback on the trunk port. Do not use direct fiber loopbacks with the GE_XP and GE_XPE card. Using direct fiber loopbacks causes irreparable damage to the GE_XP and GE_XPE card.
–Connectors: LC
•Transmitter (trunk side)
–Maximum transmitter output power: +3 dBm
–Minimum transmitter output power: -1 dBm
–Transmitter: EML laser
–Wavelength stability (drift): +/- 100 picometers (pm)
Note An optical device on the card keeps the laser wavelength locked as closely as possible to the ITU nominal value. The allowed drift is +/- 25 pm.
•Currently available wavelengths and versions of GE_XP, 10GE_XP, GE_XPE, and 10GE_XPE: C Band, 100 GHz spacing.
•Receiver (trunk side, see Table A-54)
–Receiver: APD
–Link loss budget: 24 dB minimum, with no dispersion or 22 dB optical path loss at
BER = 1 * 10 exp - 12 including dispersion
Table A-54 GE_XP and GE_XPE Card Receiver Trunk Side Specifications
|
|
FEC Type
|
Pre-FEC BER
|
Post-FEC BER
|
|
Chromatic Dispersion Tolerance
|
30 dB
|
Off
|
1.00E - 12
|
N/A
|
- 7 to - 23 dBm
|
—
|
30 dB
|
Off
|
1.00E - 12
|
N/A
|
- 7 to - 20 dBm
|
- 500 to 1600 ps/nm
|
24 dB
|
Off
|
1.00E - 12
|
N/A
|
- 7 to - 18 dBm
|
—
|
27 dB
|
Off
|
1.00E - 12
|
N/A
|
- 7 to - 18 dBm
|
- 500 to 1600 ps/nm
|
18 dB
|
Standard
|
1.00E - 05
|
1.00E - 15
|
- 7 to - 18 dBm
|
—
|
19 dB
|
Standard
|
1.00E - 05
|
1.00E - 15
|
- 7 to - 18 dBm
|
- 500 to 1600 ps/nm
|
30 dB
|
Enhanced
|
1.00E - 04
|
1.00E - 15
|
- 7 to - 27 dBm
|
—
|
30 dB
|
Enhanced
|
1.00E - 04
|
1.00E - 15
|
- 7 to - 24 dBm
|
- 500 to 1600 ps/nm
|
15 dB
|
Enhanced
|
1.00E - 04
|
1.00E - 15
|
- 7 to - 18 dBm
|
—
|
15 dB
|
Enhanced
|
1.00E - 04
|
1.00E - 15
|
- 7 to - 18 dBm
|
- 500 to 1600 ps/nm
|
•Line (client side)
–Bit rate: 1.125Gbps (GE) or 10.3125Gbps (10GE)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode or 850-nm multimode
–Maximum chromatic dispersion allowance: 12 ps/nm (SR SFP version)
–Loopback modes: Terminal and facility
–Connectors: LC (optical)
•Transmitter (client side): Depends on the SFP that is used.
•Receiver (client side): Depends on the SFP that is used.
•Environmental
–Power consumption: 95.00 W (maximum), 2 A at -48 V for GE_XP and GE_XPE cards
–Power consumption: 80.00 W (maximum), 1.67 A at -48 V for 10GE_XP and 10GE_XPE cards
•Dimensions
–Height: 12.992 in. (330 mm)
–Width: 10GE_XP and 10GE_XPE: 0.921 in. (23.4 mm)
GE_XP and GE_XPE: 1.866 in. (47.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.448 in. (240 mm)
–Weight not including clam shell: 10GE-XP and 10GE_XPE, 1.04 kg;
GE-XP and GE_XPE, 1.36 kg.
A.10.19 OTU2_XP Card Specifications
The OTU2_XP card has the following specifications:
•Line
–Bit rate: OC-192/STM-64 (9.95328 Gbps), 10GE (10.3125 Gbps), or 10G FC (10.51875 Gbps)
–Code: Scrambled NRZ
–Fiber: 1310-nm single-mode for ONS-XC-10GS1 XFP or 1530.33-nm to 1561.42-nm single-mode for ONS-XC-10G-xx.x XFP
–Maximum chromatic dispersion allowance: Depends on the XFP that is used
–Loopback modes: Terminal and facility
–Connectors: LC
•Transmitter (trunk side)
–Transmitter: EML
–Maximum transmitter output power: Depends on the XFP that is used
–Minimum transmitter output power: Depends on the XFP that is used
–Wavelength stability (drift): Depends on the XFP that is used
•Receiver (trunk side)
–Receiver: APD
–Receiver input wavelength range: Depends on XFP that is used
–Receiver sensitivity: Depends on XFP that is used
–Link loss budget: Depends on XFP that is used
•Dimensions
–Height: 13.043 in. (331.3 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 9.413 in. (239.1 mm)
–Depth with backplane connector: 9.909 in. (251.7 mm)
–Weight not including clam shell: 2.38 lb (1.08 kg)
A.11 TDC-CC and TDC-FC Card Specifications
The TDC-CC and TDC-FC card specifications are as follows:
•Wavelength
–Total operating signal wavelength range (C-band range): 1529.0 - 1562.5 nm
•Optical
–Insertion loss — DC-RX to DC-TX: Maximum 12.5 for TDC-CC and 9.5 for TDC-FC @ 1545.32 nm at room temperature
•Wavelength dependant loss: 0.8 dB max
–Maximum optical input power: 200mW
–Polarization dependent loss: 0.2 dB max
•Dimensions
–Height: 12.65 in. (332 mm)
–Width: 0.921 in. (23.4 mm) (The dimension of the finger gasket is not included)
–Depth: 8.66 in. (220.1 mm)
–Depth with backplane connector: 235 mm (9.250 in)
–Weight not including clam shell:
•TDC-CC—1.26 Kg
•TDC-FC—1.14 Kg
•The TDC-CC and TDC-FC tunable CD values are listed in Table A-55.
Table A-55 TDC-CC and TDC-FC Tunable CD Value
Unit Configuration
|
TDC-CC [ps/nm]
|
TDC-FC [ps/nm]
|
0
|
0 1
|
02
|
1
|
-110
|
-45
|
2
|
-220
|
-90
|
3
|
-330
|
-135
|
4
|
-440
|
-180
|
5
|
-550
|
-225
|
6
|
-660
|
-270
|
7
|
-770
|
-315
|
8
|
-880
|
-360
|
9
|
-990
|
-405
|
10
|
-1100
|
-450
|
11
|
-1210
|
-495
|
12
|
-1320
|
-540
|
13
|
-1430
|
-585
|
14
|
-1540
|
-630
|
15
|
-1650
|
-675
|
A.12 Mesh Patch Panel Specifications
This section provides specifications for the PP-MESH-4, PP-MESH-8, and 15454-PP-4-SMR patch panels.
A.12.1 PP-MESH-4 Patch Panel Specifications
The PP-MESH-4 patch panel optical specifications are listed in Table A-56.
Table A-56 PP-MESH-4 Patch Panel Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Wavelength range
|
—
|
—
|
1530
|
1570
|
nm
|
Insertion loss 1 2
|
—
|
In all the wavelength ranges
(local ADD or test access RX to EXP TX, COM RX to EXP TX, COM RX to test access TX)
|
—
|
7.5
|
dB
|
Insertion Loss Uniformity1 2
|
—
|
In all the wavelength ranges
|
—
|
0.9
|
dB
|
Polarization dispersion loss (PDL) 1
|
—
|
—
|
—
|
0.3
|
dB
|
Polarization mode dispersion (PMD) 1
|
—
|
—
|
—
|
0.1
|
dB
|
Optical Return Loss 1
|
—
|
—
|
50
|
—
|
dB
|
Directivity 1
|
—
|
—
|
50
|
—
|
dB
|
The PP-MESH-4 patch panel has the following additional specifications:
•Environmental
–Operating temperature: +23 to +149 degrees Fahrenheit (-5 to +65 degrees Celsius)
–Operating humidity: 5 to 95 percent, noncondensing
•Dimensions
–Height: 17.42 in. (442.5 mm)
–Width: 3.457 in. (87.8 mm)
–Depth: 11.025 in. (280 mm)
A.12.2 PP-MESH-8 Patch Panel Specifications
The PP-MESH-8 patch panel optical specifications are listed in Table A-57.
Table A-57 PP-MESH-8 Patch Panel Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Wavelength range
|
—
|
—
|
1530
|
1570
|
nm
|
Insertion loss 1 2
|
—
|
In all the wavelength ranges
(local ADD or test access RX to EXP TX, COM RX to EXP TX, COM RX to test access TX)
|
—
|
10.6
|
dB
|
Insertion loss uniformity 1 2
|
—
|
In all the wavelength ranges
|
—
|
1.3
|
dB
|
PDL 1
|
—
|
—
|
—
|
0.5
|
dB
|
PMD 1
|
—
|
—
|
—
|
0.1
|
dB
|
Optical Return Loss 1
|
—
|
—
|
50
|
—
|
dB
|
Directivity 1
|
—
|
—
|
50
|
—
|
dB
|
The PP-MESH-8 patch panel has the following additonal specifications:
•Environmental
–Operating temperature: +23 to +149 degrees Fahrenheit (-5 to +65 degrees Celsius)
–Operating humidity: 5 to 95 percent, noncondensing
•Dimensions
–Height: 17.42 in. (442.5 mm)
–Width: 3.457 in. (87.8 mm)
–Depth: 11.025 in. (280 mm)
A.12.3 15454-PP-4-SMR Patch Panel Specifications
The 15454-PP-4-SMR patch panel optical specifications are listed in Table A-58.
Table A-58 15454-PP-4-SMR Patch Panel Optical Specifications
Parameter
|
Note
|
Condition
|
Min
|
Max
|
Unit
|
Wavelength range
|
All SOP within operating temperature range
|
—
|
1520
|
1570
|
nm
|
Insertion loss
|
All SOP within operating temperature range, wavelength range, from each input port of any MPO connector to any output port including two MPO connections
|
—
|
5.5
|
7.5
|
dB
|
Insertion loss uniformity 1
|
—
|
—
|
0.5
|
dB
|
Insertion loss ripple
|
—
|
—
|
0.2
|
dB
|
Chromatic dispersion
|
—
|
—
|
+/- 5
|
ps/nm
|
PDL
|
—
|
—
|
0.1
|
dB
|
PMD
|
—
|
—
|
0.1
|
dB
|
Optical return loss
|
—
|
50
|
—
|
dB
|
Directivity
|
—
|
50.0
|
—
|
dB
|
The 15454-PP-4-SMR patch panel has the following additional specifications:
•Environmental
–Operating temperature: +23 to +149 degrees Fahrenheit (-5 to +65 degrees Celsius)
A.13 SFP and XFP Specifications
Note The CC-FTA fan tray is mandatory if CWDM SFPs and DWDM SFPs are used on MSTP units.
Note Use hardware version 2.0 DWDM SFP for MSTP units.
See the Installing the GBIC, SFP, SFP+, XFP, CXP, and CFP Optical Modules in Cisco ONS Platforms for SFP and XFP specifications.
A.14 Patch Panel Specifications
For information on 15216 40-Channel Mux/Demux Patch Panel specifications, refer to the "Patch Panel Specifications" section in the "Installing Cisco ONS 15216 40-Channel Mux/Demux Patch Panel" guide.
For information on 15454-PP-4-SMR Patch Panel specifications, refer to the "Patch Panel Specifications" section in the "Installing Cisco ONS 15454-PP-4-SMR Patch Panel" guide.
Feedback
