Table Of Contents
ISC Runtime Configuration Information
Default TCP Port Values and Protocol Directions Used by ISC
Command-Line Interfaces Used by ISC
ISC Runtime Configuration Information
This chapter explains the following ISC information for runtime configuration:
•
Default TCP Port Values and Protocol Directions Used by ISC
•Command-Line Interfaces Used by ISC
Default TCP Port Values and Protocol Directions Used by ISC
ISC uses various Transmission Control Protocol (TCP) ports during its operation. Most TCP ports are configured during the installation. Table D-1 and Table D-2 specify the most vital TCP primary and optional ports, respectively, their default values, and the direction.
Table D-1 ISC Primary TCP Ports, Their Default Values, and Direction
TCP Primary Ports (listed alphabetically)
|
Default Values
|
Direction
|
Notes
|
HTTP
|
8030
|
Web browser to ISC
|
Used for Web GUI and NBI
|
Tibco RVA
|
7600
|
ISC to web browser
|
used by some applications
|
Tomcat
|
8031
|
Web browser to ISC
|
HTTP port value + 1
|
Table D-2 ISC Optional TCP Ports, Their Default Values, and Direction
TCP Optional Ports (listed alphabetically)
|
Default Values
|
Direction
|
Notes
|
HTTPS
|
8443
|
Web browser to ISC
|
if HTTPS activated
|
Naming
|
1030
|
Collection Server (CS) or Processing Server (PS) to Master
|
if ISC installed on distributed servers
|
Naming + 1
|
1031
|
CS or PS to Master
|
if ISC installed on distributed servers
|
Oracle
|
1521
|
ISC to Oracle Server
|
if Oracle database is used
|
Oracle
|
1521
|
CS, PS, or Master to Oracle
|
if Oracle used and distributed ISC servers
|
Sybase
|
2630
|
CS or PS to Master
|
if ISC installed on distributed servers
|
Tibco RVA Admin
|
7630
|
Web browser to ISC
|
if RVA config required
|
Tibco RVD or RVRD
|
7530
|
bi-directional between CS or PS and Master
|
if ISC installed on distributed servers
|
Tibco RVD or RVRD
|
7530
|
bi-directional between ISC and IE2100
|
if using CNS transport mechanism for device access
|
Tibco RVRD Admin
|
7580
|
Web browser to ISC
|
if RVRD config required
|
The values selected during the installation can be retrieved from the file $ISC_HOME/etc/install.cfg. Most of these ports only need to be allowed if you are allowing users to access ISC from outside your firewall. These ports are used by ISC to communicate between the database server and its support servers (processing server, interface server, and so on), if they are installed.
ISC uses or can us the protocols specified in Table D-3 to communicate with the routers under its configuration control.
Note The selected protocol for each of the following categories must be able to pass through any firewalls between ISC and the devices:
1. Terminal Session Protocol - default: Telnet; SSH; CNS*; rsh
2. Configuration Access Protocol - default: selected Terminal Session Protocol; TFTP; FTP; rcp
3. SNMP - default: SNMPv1/v2c; SNMPv3
* CNS is a transport mechanism that uses the TIB/Rendezvous event bus to communicate with an IE2100..
Table D-3 Protocols and Directions with ISC
Protocols
(listed alphabetically)
|
Directions
|
FTP
|
Devices to FTP server
|
NFS
|
Between ISC and TFTP or FTP server if server is on a different machine. (Can be blocked if you do not use FTP or TFTP.)
|
rcp
|
ISC to devices
|
rsh
|
ISC to devices
|
SSH
|
ISC to devices
|
SNMP
|
ISC to devices
|
SNMPv3
|
ISC to devices
|
Telnet
|
ISC to devices
|
TFTP
|
Devices to TFTP server
|
Note Device creation is explained in the chapter Service Inventory—Inventory and Connection Manager, in Cisco IP Solution Center Infrastructure Reference, 4.1.
Command-Line Interfaces Used by ISC
This section specifies the command-line interfaces (CLIs) used by ISC:
•config term
•copy (many variations)
•enable
•end
•exit
•ping [vrf]
•reload
•show diag
•show etherchannel port
•show interfaces switchport
•show modules
•show port
•show running
•show startup
•show ver
•term (length, width, editing)
•write mem
•[no] logging console
Feedback
