Cisco IP Solution Center Installation Guide, 3.2 - Setting Up Cisco CNS IE2100 Appliances Running Cisco CNS Configuration Engine 1.3.x and 1.4 Software with ISC [Cisco IP Solution Center]

Table Of Contents

Setting Up Cisco CNS IE2100 Appliances Running Cisco CNS Configuration Engine 1.3.x and 1.4 Software with ISC

Overview

SetUp Steps

Set Up Cisco CNS IE2100 Appliance

Configure a TIBCO Rendezvous Routing Daemon

Configuring the rvrd Daemon on the ISC Master Machine

Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance

Testing rv Connectivity Between ISC and Cisco CNS IE2100

Checking Router Configurations Overview

Setting Up Cisco CNS IE2100 Appliances Running Cisco CNS Configuration Engine 1.3.x and 1.4 Software with ISC

Overview

Cisco IP Solution Center (ISC) supports the Device Access Protocol (DAP) of CNS for communication with any Cisco IOS device. The DAP includes:

•uploading a configuration file from a device

•downloading a configlet to a device

•executing a command on a device and obtaining the result (all communications).

ISC supports CNS Plug-and-Play.

In addition to this Overview section, this chapter contains the following major sections:

•SetUp Steps

•Checking Router Configurations Overview

SetUp Steps

To enable the Cisco CNS Intelligence Engine 2100 (IE2100) Series Configuration Engine functionality on ISC, set up in the following order:

1. Set up the Cisco CNS IE2100 device, as shown in "Set Up Cisco CNS IE2100 Appliance."

2. Configure a TIBCO Rendezvous Routing Daemon (rvrd), as shown in "Configure a TIBCO Rendezvous Routing Daemon."

Set Up Cisco CNS IE2100 Appliance

ISC supports the integration with Cisco CNS IE2100 appliances running Cisco CNS Configuration Engine 1.3.x and 1.4 software.

For the Cisco CNS Configuration Engine 1.3.x software installation and setup, see the Cisco CNS Configuration Engine 1.3.x documentation set at:

http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cns/ce/rel13/index.htm

For the Cisco CNS Configuration Engine 1.4 software installation and setup, see the Cisco CNS Configuration Engine 1.4 documentation set at:

http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cns/ce/rel14/index.htm

On a freshly set up Cisco CNS IE2100 appliance, remove Pluto protection, as follows.

Step 1 Log in as root.

Step 2 Enter:

plutosetup.

Step 3 A warning appears:

"plutosetup will open some class files to public access. It is a security risk."

Continue (y/n):

Answer y for yes to the above warning.

Note Because the Cisco CNS IE2100 appliance and the ISC Master server are behind a secure barrier, we can safely answer y for yes to the security risk warning message above. This removal of Pluto protection exposes some files in Cisco CNS IE2100 that allow ISC to create, delete, and edit devices in the IE2100 repository. This is needed for proper ISC to Cisco CNS Configuration Engine 1.3.x and 1.4 integration. Removal of Pluto protection only needs to occur when a particular Cisco CNS IE2100 appliance is first used and every time the file /opt/CSCOcnsie/bin/pluto is deleted for any reason.

Configure a TIBCO Rendezvous Routing Daemon

In this section, do the following:

1. Configuring the rvrd Daemon on the ISC Master Machine

2. Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance

3. Testing rv Connectivity Between ISC and Cisco CNS IE2100

Configuring the rvrd Daemon on the ISC Master Machine

To configure an rvrd daemon on an ISC Master server, do the following:

Step 1 The TIBCO Rendezvous Routing Daemon (rvrd) is the default daemon on the ISC Master server

To configure an rvrd daemon on an ISC Master server, start an ISC-supported browser and go to the following URL: http://<isc_hostname>:7580 or http://<isc_ip_address>:7580

Step 2 Look at the component field under the General Information link to verify that rvrd is running. It should say rvrd, as shown in Figure B-1, "ISC rvrd Verification."

Figure B-1 ISC rvrd Verification

Step 3 Click on the Routers link in the left column.

Step 4 A security alert window appears, asking you if you want to proceed. Answer Yes or Next, depending on your browser, to continue.

Step 5 Verify that ISC automatically created the Router Name <isc_hostname> for the ISC Master server.

Step 6 In the Local Network column, click the current entry in the field (this number indicates the number of local networks currently defined). Verify that ISC automatically created the isc network with the following values:

a. The Local Network Name: isc.

b. The Service, the TIBCO port number for the ISC installation (default: 7530).

c. The Network Specification field is optional.

d. No change in the value of the Cost field.

Step 7 Click on the isc entry created in the Local Network Name column.

Step 8 Verify that ISC automatically added Subjects cisco.cns.> and cisco.mgmt.cns.> to both the Import Subjects and Export Subjects columns.

Step 9 Again, click on the Routers link in the left column.

Step 10 In the Neighbor column, click the current entry in the field (this number indicates the number of neighbors currently defined).

Step 11 In the Local Endpoint section, if you choose a port number other than the default, be sure the Port for Local Endpoint defined on the ISC Master server equals the Port for Remote Endpoint defined on the Cisco CNS IE2100 appliance (defined in Step 22 c. of the section "Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance").

Step 12 Add the following in the Remote Endpoint section:

a. In the Host field, add the IP address or hostname of the Cisco CNS IE2100 appliance.

b. If you choose a port number other than the default, the Port for Remote Endpoint defined on the ISC Master server must equal the Port for Local Endpoint defined on the Cisco CNS IE2100 appliance (defined in Step 22 d. of the section "Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance").

c. In the Router Name field, enter the name of the Cisco CNS IE2100 appliance followed by -ie2100. Any unique name works, but this recommendation is synchronized with this example.

Example: <ie2100_hostname>-ie2100

Note It is very important that the Neighbor Name is the same as the router name configured on the Cisco CNS IE2100 appliance.

d. Click Add Neighbor Interface. The entered values appear in the corresponding columns in the upper section of the page.

Note If you encountered any error, select the check box for the row of information you want to remove, then click Remove Selected Neighbor Interface(s).

Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance

To configure an rvrd daemon on a Cisco CNS IE2100 appliance, do the following:

Step 1 The TIBCO Rendezvous Routing Daemon (rvrd) is the default daemon on the Cisco CNS IE2100 appliance.

To configure an rvrd daemon on a Cisco CNS IE2100 appliance, start an ISC-supported browser and go to the following URL: http://<ie2100_hostname>:7580 or http://<ie2100_ip_address>:7580.

Step 2 Look at the component field under the information link to verify that rvrd is running. It should say rvrd, as shown in Figure B-2, "Cisco CNS IE2100 rvrd Verification."

Figure B-2 Cisco CNS IE2100 rvrd Verification

Step 3 Click on the routers link in the left column.

Step 4 In the Add Router Name field in the upper part of the window, enter the name of the Cisco CNS IE2100 appliance, followed by -ie2100. Any unique name works, but this recommendation is synchronized with this example.

Example: <ie2100_hostname>-ie2100

Step 5 Click Add to create an entry with the new router name.

The chosen name appears in the Router Name column in the lower part of the window.

Step 6 In the Local Networks column, click the current entry in the field (this number indicates the number of local networks currently defined).

Step 7 Specify the local Cisco CNS IE2100 network with the following values:

a. In the Local Network Name field, enter the unique name entered in Step 6 a. of the section "Configuring the rvrd Daemon on the ISC Master Machine". In the example, this is isc.

b. In the Service field, add the TIBCO port number for the ISC installation (default: 7530).

c. The Network Specification field is optional. You can enter a description.

Step 8 Click Add Local Network. The entered values appear in the corresponding columns in the lower section of the page.

Step 9 Click on the entry just created. In this example, it is isc.

Step 10 In the Add Subject field, enter cisco.cns.>.

Step 11 Click Add for Import and Export. The entered values appear in the Imported Subjects and Exported Subjects columns in the lower part of the window.

Step 12 If you are using Cisco CNS Configuration Engine 1.3.2 or 1.4 in the Subject field in the lower part of the window, enter cisco.mgmt.cns.>, repeat Step 11, and then proceed to Step 13. If you are using Cisco CNS Configuration Engine 1.3 or 1.3.1, just proceed to Step 13.

Step 13 Click the routers link in the left column.

Step 14 In the Local Networks column, click the current entry in the field (this is at least 1 now, because you already added one local network).

Step 15 Specify the local Cisco CNS IE2100 network with the following values:

a. In the Local Network Name field, add a unique name. For example: ie2100-eventBus.

b. In the Service field, add the CNS Event Bus Service Parameter value defined in the setup of the Cisco CNS IE2100 appliance (default: 7500).

c. In the Network Specification field, leave it blank or enter the name of the Cisco CNS IE2100 appliance.

Note If you encountered any error, select the check box for the row of information you want to remove, then click Remove Marked Items.

Step 16 Click on the entry just created in the Local Network Name column.

Step 17 In the Add Subject field in the upper part of the window, enter cisco.cns.>.

Step 18 Click Add for Import and Export. The entered values appear in the Imported Subjects and Exported Subjects columns in the upper part of the window.

Step 19 If you are using Cisco CNS Configuration Engine 1.3.2 or 1.4, in the Subject field in the lower part of the window, enter cisco.mgmt.cns.>, repeat Step 18, and then proceed to Step 20. If you are using Cisco CNS Configuration Engine 1.3 or 1.3.1, just proceed to Step 20.

Step 20 Click the routers link in the left column.

Step 21 In the Neighbors column, click the current entry in the field (this number indicates the number of neighbors currently defined).

Step 22 Add the following in the Neighbors Configuration window:

a. In the Neighbor Name column, add the router name as automatically configured on the ISC Master server, and verified in Step 5 of the section "Configuring the rvrd Daemon on the ISC Master Machine." This router name is <isc_hostname>.

Note It is very important that the Neighbor Name is the same as the router name configured on the ISC Master server.

b. In the Hostname or IP addr column, add the host name or IP address of the ISC Master server.

c. In the Remote column, add the Port number for the Local Endpoint defined on the ISC Master server in Step 11 of the section "Configuring the rvrd Daemon on the ISC Master Machine."

d. In the Local column, add the Port number for Remote Endpoint defined on the ISC Master server, in Step 12 b. of the section "Configuring the rvrd Daemon on the ISC Master Machine."

Step 23 Click Add Active [all].

A good indication that the connection is established is when the new name in the Neighbor Name column appears as a hyperlink in the bottom of the window. It takes a few seconds for this to occur. Also, it is recommended to click Refresh a few times to see the hyperlink.

Note If you encountered any error, select the check box for the row of information you want to remove, then click Remove Marked Items.

Testing rv Connectivity Between ISC and Cisco CNS IE2100

Test that the rvrd setup has been successful, by testing the following:

•Connectivity from ISC Master Server to Cisco CNS IE2100 Appliance

•Connectivity from Cisco CNS IE2100 Appliance to ISC Master Server.

Connectivity from ISC Master Server to Cisco CNS IE2100 Appliance

Test the successful setup of connectivity from an ISC Master server to a Cisco CNS IE2100 appliance:

Step 1 Telnet to the Cisco CNS IE2100 appliance.

Step 2 Go to the following directory:

cd /opt/CSCOcnsie/tools

Step 3 Set up a TIBCO Listener to the TIBCO port the ISC installation is running and as configured above (default: 7530):

./cns-listen -service <tibco_port_number> "cisco.cns.>"

Leave the Listener running in this window.

Step 4 In a separate window, navigate to the following directory:

cd /<isc_install_directory>/thirdparty/rv/bin

Step 5 Send a TIBCO message to the Cisco CNS IE2100 appliance on the configured TIBCO port number (default: 7530):

/tibrvsend -service <tibco_port_number> "cisco.cns.config-changed" "<variable_message>"

Step 6 If the message is seen in the Listener window on the Cisco CNS IE2100 appliance, connectivity is established correctly from the ISC Master server to the Cisco CNS IE2100 appliance for the TIBCO subject "cisco.cns.>".

Step 7 If you are using Cisco CNS Configuration Engine Release 1.3.2 or 1.4, proceed with Step 8 to Step 12. Otherwise, proceed to the "Connectivity from Cisco CNS IE2100 Appliance to ISC Master Server" section."

Step 8 Telnet to the Cisco CNS IE2100 appliance.

Step 9 Go to the following directory:

cd /opt/CSCOcnsie/tools

Step 10 Set up a TIBCO Listener to the TIBCO port the ISC installation is running and as configured above (default: 7530):

./cns-listen -service <tibco_port_number> "cisco.mgmt.cns.>"

Leave the Listener running in this window.

Step 11 In the window created in Step 4, send a TIBCO message to the Cisco CNS IE2100 appliance on the configured TIBCO port number (default: 7530):

/tibrvsend -service <tibco_port_number> "cisco.mgmt.cns.config-changed" "<variable_message>"

Step 12 If the message is seen in the Listener window on the Cisco CNS IE2100 appliance, connectivity is established correctly from the ISC Master server to the Cisco CNS IE2100 appliance for the TIBCO subject "cisco.mgmt.cns.>".

Connectivity from Cisco CNS IE2100 Appliance to ISC Master Server

Test the successful setup of connectivity from a Cisco CNS IE2100 appliance to an ISC Master Server, as follows:

Step 1 On the ISC device, go to the following directory:

cd /<isc_install_directory>/thirdparty/rv/bin

Step 2 Set up a TIBCO Listener to the TIBCO port that isc installation is running and as configured above (default: 7530):

./tibrvlisten -service <tibco_port_number> "cisco.cns.>"

Leave the Listener running in this window.

Step 3 In a separate window, telnet to the Cisco CNS IE2100 appliance.

Step 4 Go to the following directory:

cd /opt/CSCOcnsie/tools

Step 5 Send a TIBCO message to the ISC Master server on the configured ISC installation port (default: 7530):

./cns-send -service <tibco_port_number> "cisco.cns.config-changed" "<variable_message>"

Step 6 If the message is seen in the Listener window on the ISC Master server, connectivity is established correctly from the Cisco CNS IE2100 appliance to the ISC Master server for the TIBCO subject "cisco.cns.>".

Step 7 If you are using Cisco CNS Configuration Engine Release 1.3.2 or 1.4, proceed with Step 8 to Step 12. Otherwise, proceed to the "Checking Router Configurations Overview" section."

Step 8 In the window created in Step 1, set up a TIBCO Listener to the TIBCO port that isc installation is running and as configured above (default: 7530):

./tibrvlisten -service <tibco_port_number> "cisco.mgmt.cns.>"

Leave the Listener running in this window.

Step 9 In a separate window, telnet to the Cisco CNS IE2100 appliance.

Step 10 Go to the following directory:

cd /opt/CSCOcnsie/tools

Step 11 Send a TIBCO message to the ISC Master server on the configured ISC installation port (default: 7530):

./cns-send -service <tibco_port_number> "cisco.mgmt.cns.config-changed" "<variable_message>"

Step 12 If the message is seen in the Listener window on the ISC Master server, connectivity is established correctly from the Cisco CNS IE2100 appliance to the ISC Master server for the TIBCO subject "cisco.mgmt.cns.>".

Checking Router Configurations Overview

The Cisco IOS image is needed for the routers used with the Cisco CNS IE2100 functionality (that is, the CNS transport mechanism and/or the CNS Plug-and-Play feature). For Cisco CNS Configuration Engine Release 1.3, the recommended Cisco IOS release is 12.2(8)T or later; for Cisco CNS Configuration Engine Release 1.3.1, 1.3.2, or 1.4, the recommended Cisco IOS release is 12.2(11)T or later. Cisco IOS releases 12.3(1)T or later are supported only by Cisco CNS Configuration Engine Releases 1.3.2 and 1.4.

Additionally, the router running a configuration must contain the following two CNS commands:

1. cns config partial <IE2100 address> 80

2. cns event <ie2100 address> 11011

or

cns event <ie2100 address> 11011 keepalive <num. of seconds> <num. of trials>

Note The keepalive option makes sure the TCP connection between the Cisco CNS IE2100 appliance and the router is alive at all times. It sends keepalive messages at <num. of seconds> intervals with <num. of trials> retries.

Also, the router startup configuration must contain the following two CNS commands:

1. cns config initial <ie2100 address> event

The cns config initial command should be configured in the startup configuration of the Cisco IOS device or router. It triggers the router to pick up and apply any initial configuration that might be waiting for it on the Cisco CNS IE2100 appliance. After the cns config initial command is executed, this command is automatically removed. The recommendation is to include the cns config partial command in the initial configuration that is waiting on the Cisco CNS IE2100 appliance. If a no persist option is used, the router does not perform a write-mem, thus keeping the startup configuration from being overwritten.

2. cns event <ie2100 address> 11011

or

cns event <ie2100 address> 11011 keepalive <num. of seconds> <num. of trials>

Note The keepalive option makes sure the TCP connection between the Cisco CNS IE2100 appliance and the router is alive at all times. It sends keepalive messages at <num. of seconds> intervals with <num. of trials> retries.

Different IOS versions can support additional CNS commands or different formats of the same CNS command. See the Cisco CNS software documentation for more details on the other possible CNS commands and their options.

	Cisco IP Solution Center Installation Guide, 3.2
	Setting Up Cisco CNS IE2100 Appliances Running Cisco CNS Configuration Engine 1.3.x and 1.4 Software with ISC
Cisco IP Solution Center Installation Guide, 3.2 Index About This Guide System Recommendations Installing and Logging Into ISC Setting Up Oracle for ISC Setting Up Cisco CNS IE2100 Appliances Running Cisco CNS Configuration Engine 1.3.x and 1.4 Software with ISC Backup and Restore of ISC Repository and Standby System Troubleshooting	Download this chapter Setting Up Cisco CNS IE2100 Appliances Running Cisco CNS Configuration Engine 1.3.x and 1.4 Software with ISC Download the complete book Cisco IP Solution Center Installation Guide, 3.2 - Entire Book in PDF (PDF - 2 MB) Feedback Table Of Contents Setting Up Cisco CNS IE2100 Appliances Running Cisco CNS Configuration Engine 1.3.x and 1.4 Software with ISC Overview SetUp Steps Set Up Cisco CNS IE2100 Appliance Configure a TIBCO Rendezvous Routing Daemon Configuring the rvrd Daemon on the ISC Master Machine Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance Testing rv Connectivity Between ISC and Cisco CNS IE2100 Checking Router Configurations Overview Setting Up Cisco CNS IE2100 Appliances Running Cisco CNS Configuration Engine 1.3.x and 1.4 Software with ISC Overview Cisco IP Solution Center (ISC) supports the Device Access Protocol (DAP) of CNS for communication with any Cisco IOS device. The DAP includes: •uploading a configuration file from a device •downloading a configlet to a device •executing a command on a device and obtaining the result (all communications). ISC supports CNS Plug-and-Play. In addition to this Overview section, this chapter contains the following major sections: •SetUp Steps •Checking Router Configurations Overview SetUp Steps To enable the Cisco CNS Intelligence Engine 2100 (IE2100) Series Configuration Engine functionality on ISC, set up in the following order: 1. Set up the Cisco CNS IE2100 device, as shown in "Set Up Cisco CNS IE2100 Appliance." 2. Configure a TIBCO Rendezvous Routing Daemon (rvrd), as shown in "Configure a TIBCO Rendezvous Routing Daemon." Set Up Cisco CNS IE2100 Appliance ISC supports the integration with Cisco CNS IE2100 appliances running Cisco CNS Configuration Engine 1.3.x and 1.4 software. For the Cisco CNS Configuration Engine 1.3.x software installation and setup, see the Cisco CNS Configuration Engine 1.3.x documentation set at: http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cns/ce/rel13/index.htm For the Cisco CNS Configuration Engine 1.4 software installation and setup, see the Cisco CNS Configuration Engine 1.4 documentation set at: http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cns/ce/rel14/index.htm On a freshly set up Cisco CNS IE2100 appliance, remove Pluto protection, as follows. Step 1 Log in as root. Step 2 Enter: plutosetup. Step 3 A warning appears: "plutosetup will open some class files to public access. It is a security risk." Continue (y/n): Answer y for yes to the above warning. Note Because the Cisco CNS IE2100 appliance and the ISC Master server are behind a secure barrier, we can safely answer y for yes to the security risk warning message above. This removal of Pluto protection exposes some files in Cisco CNS IE2100 that allow ISC to create, delete, and edit devices in the IE2100 repository. This is needed for proper ISC to Cisco CNS Configuration Engine 1.3.x and 1.4 integration. Removal of Pluto protection only needs to occur when a particular Cisco CNS IE2100 appliance is first used and every time the file /opt/CSCOcnsie/bin/pluto is deleted for any reason. Configure a TIBCO Rendezvous Routing Daemon In this section, do the following: 1. Configuring the rvrd Daemon on the ISC Master Machine 2. Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance 3. Testing rv Connectivity Between ISC and Cisco CNS IE2100 Configuring the rvrd Daemon on the ISC Master Machine To configure an rvrd daemon on an ISC Master server, do the following: Step 1 The TIBCO Rendezvous Routing Daemon (rvrd) is the default daemon on the ISC Master server To configure an rvrd daemon on an ISC Master server, start an ISC-supported browser and go to the following URL: http://<isc_hostname>:7580 or http://<isc_ip_address>:7580 Step 2 Look at the component field under the General Information link to verify that rvrd is running. It should say rvrd, as shown in Figure B-1, "ISC rvrd Verification." Figure B-1 ISC rvrd Verification Step 3 Click on the Routers link in the left column. Step 4 A security alert window appears, asking you if you want to proceed. Answer Yes or Next, depending on your browser, to continue. Step 5 Verify that ISC automatically created the Router Name <isc_hostname> for the ISC Master server. Step 6 In the Local Network column, click the current entry in the field (this number indicates the number of local networks currently defined). Verify that ISC automatically created the isc network with the following values: a. The Local Network Name: isc. b. The Service, the TIBCO port number for the ISC installation (default: 7530). c. The Network Specification field is optional. d. No change in the value of the Cost field. Step 7 Click on the isc entry created in the Local Network Name column. Step 8 Verify that ISC automatically added Subjects cisco.cns.> and cisco.mgmt.cns.> to both the Import Subjects and Export Subjects columns. Step 9 Again, click on the Routers link in the left column. Step 10 In the Neighbor column, click the current entry in the field (this number indicates the number of neighbors currently defined). Step 11 In the Local Endpoint section, if you choose a port number other than the default, be sure the Port for Local Endpoint defined on the ISC Master server equals the Port for Remote Endpoint defined on the Cisco CNS IE2100 appliance (defined in Step 22 c. of the section "Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance"). Step 12 Add the following in the Remote Endpoint section: a. In the Host field, add the IP address or hostname of the Cisco CNS IE2100 appliance. b. If you choose a port number other than the default, the Port for Remote Endpoint defined on the ISC Master server must equal the Port for Local Endpoint defined on the Cisco CNS IE2100 appliance (defined in Step 22 d. of the section "Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance"). c. In the Router Name field, enter the name of the Cisco CNS IE2100 appliance followed by -ie2100. Any unique name works, but this recommendation is synchronized with this example. Example: <ie2100_hostname>-ie2100 Note It is very important that the Neighbor Name is the same as the router name configured on the Cisco CNS IE2100 appliance. d. Click Add Neighbor Interface. The entered values appear in the corresponding columns in the upper section of the page. Note If you encountered any error, select the check box for the row of information you want to remove, then click Remove Selected Neighbor Interface(s). Configuring the rvrd Daemon on a Cisco CNS IE2100 Appliance To configure an rvrd daemon on a Cisco CNS IE2100 appliance, do the following: Step 1 The TIBCO Rendezvous Routing Daemon (rvrd) is the default daemon on the Cisco CNS IE2100 appliance. To configure an rvrd daemon on a Cisco CNS IE2100 appliance, start an ISC-supported browser and go to the following URL: http://<ie2100_hostname>:7580 or http://<ie2100_ip_address>:7580. Step 2 Look at the component field under the information link to verify that rvrd is running. It should say rvrd, as shown in Figure B-2, "Cisco CNS IE2100 rvrd Verification." Figure B-2 Cisco CNS IE2100 rvrd Verification Step 3 Click on the routers link in the left column. Step 4 In the Add Router Name field in the upper part of the window, enter the name of the Cisco CNS IE2100 appliance, followed by -ie2100. Any unique name works, but this recommendation is synchronized with this example. Example: <ie2100_hostname>-ie2100 Step 5 Click Add to create an entry with the new router name. The chosen name appears in the Router Name column in the lower part of the window. Step 6 In the Local Networks column, click the current entry in the field (this number indicates the number of local networks currently defined). Step 7 Specify the local Cisco CNS IE2100 network with the following values: a. In the Local Network Name field, enter the unique name entered in Step 6 a. of the section "Configuring the rvrd Daemon on the ISC Master Machine". In the example, this is isc. b. In the Service field, add the TIBCO port number for the ISC installation (default: 7530). c. The Network Specification field is optional. You can enter a description. Step 8 Click Add Local Network. The entered values appear in the corresponding columns in the lower section of the page. Step 9 Click on the entry just created. In this example, it is isc. Step 10 In the Add Subject field, enter cisco.cns.>. Step 11 Click Add for Import and Export. The entered values appear in the Imported Subjects and Exported Subjects columns in the lower part of the window. Step 12 If you are using Cisco CNS Configuration Engine 1.3.2 or 1.4 in the Subject field in the lower part of the window, enter cisco.mgmt.cns.>, repeat Step 11, and then proceed to Step 13. If you are using Cisco CNS Configuration Engine 1.3 or 1.3.1, just proceed to Step 13. Step 13 Click the routers link in the left column. Step 14 In the Local Networks column, click the current entry in the field (this is at least 1 now, because you already added one local network). Step 15 Specify the local Cisco CNS IE2100 network with the following values: a. In the Local Network Name field, add a unique name. For example: ie2100-eventBus. b. In the Service field, add the CNS Event Bus Service Parameter value defined in the setup of the Cisco CNS IE2100 appliance (default: 7500). c. In the Network Specification field, leave it blank or enter the name of the Cisco CNS IE2100 appliance. Note If you encountered any error, select the check box for the row of information you want to remove, then click Remove Marked Items. Step 16 Click on the entry just created in the Local Network Name column. Step 17 In the Add Subject field in the upper part of the window, enter cisco.cns.>. Step 18 Click Add for Import and Export. The entered values appear in the Imported Subjects and Exported Subjects columns in the upper part of the window. Step 19 If you are using Cisco CNS Configuration Engine 1.3.2 or 1.4, in the Subject field in the lower part of the window, enter cisco.mgmt.cns.>, repeat Step 18, and then proceed to Step 20. If you are using Cisco CNS Configuration Engine 1.3 or 1.3.1, just proceed to Step 20. Step 20 Click the routers link in the left column. Step 21 In the Neighbors column, click the current entry in the field (this number indicates the number of neighbors currently defined). Step 22 Add the following in the Neighbors Configuration window: a. In the Neighbor Name column, add the router name as automatically configured on the ISC Master server, and verified in Step 5 of the section "Configuring the rvrd Daemon on the ISC Master Machine." This router name is <isc_hostname>. Note It is very important that the Neighbor Name is the same as the router name configured on the ISC Master server. b. In the Hostname or IP addr column, add the host name or IP address of the ISC Master server. c. In the Remote column, add the Port number for the Local Endpoint defined on the ISC Master server in Step 11 of the section "Configuring the rvrd Daemon on the ISC Master Machine." d. In the Local column, add the Port number for Remote Endpoint defined on the ISC Master server, in Step 12 b. of the section "Configuring the rvrd Daemon on the ISC Master Machine." Step 23 Click Add Active [all]. A good indication that the connection is established is when the new name in the Neighbor Name column appears as a hyperlink in the bottom of the window. It takes a few seconds for this to occur. Also, it is recommended to click Refresh a few times to see the hyperlink. Note If you encountered any error, select the check box for the row of information you want to remove, then click Remove Marked Items. Testing rv Connectivity Between ISC and Cisco CNS IE2100 Test that the rvrd setup has been successful, by testing the following: •Connectivity from ISC Master Server to Cisco CNS IE2100 Appliance •Connectivity from Cisco CNS IE2100 Appliance to ISC Master Server. Connectivity from ISC Master Server to Cisco CNS IE2100 Appliance Test the successful setup of connectivity from an ISC Master server to a Cisco CNS IE2100 appliance: Step 1 Telnet to the Cisco CNS IE2100 appliance. Step 2 Go to the following directory: cd /opt/CSCOcnsie/tools Step 3 Set up a TIBCO Listener to the TIBCO port the ISC installation is running and as configured above (default: 7530): ./cns-listen -service <tibco_port_number> "cisco.cns.>" Leave the Listener running in this window. Step 4 In a separate window, navigate to the following directory: cd /<isc_install_directory>/thirdparty/rv/bin Step 5 Send a TIBCO message to the Cisco CNS IE2100 appliance on the configured TIBCO port number (default: 7530): /tibrvsend -service <tibco_port_number> "cisco.cns.config-changed" "<variable_message>" Step 6 If the message is seen in the Listener window on the Cisco CNS IE2100 appliance, connectivity is established correctly from the ISC Master server to the Cisco CNS IE2100 appliance for the TIBCO subject "cisco.cns.>". Step 7 If you are using Cisco CNS Configuration Engine Release 1.3.2 or 1.4, proceed with Step 8 to Step 12. Otherwise, proceed to the "Connectivity from Cisco CNS IE2100 Appliance to ISC Master Server" section." Step 8 Telnet to the Cisco CNS IE2100 appliance. Step 9 Go to the following directory: cd /opt/CSCOcnsie/tools Step 10 Set up a TIBCO Listener to the TIBCO port the ISC installation is running and as configured above (default: 7530): ./cns-listen -service <tibco_port_number> "cisco.mgmt.cns.>" Leave the Listener running in this window. Step 11 In the window created in Step 4, send a TIBCO message to the Cisco CNS IE2100 appliance on the configured TIBCO port number (default: 7530): /tibrvsend -service <tibco_port_number> "cisco.mgmt.cns.config-changed" "<variable_message>" Step 12 If the message is seen in the Listener window on the Cisco CNS IE2100 appliance, connectivity is established correctly from the ISC Master server to the Cisco CNS IE2100 appliance for the TIBCO subject "cisco.mgmt.cns.>". Connectivity from Cisco CNS IE2100 Appliance to ISC Master Server Test the successful setup of connectivity from a Cisco CNS IE2100 appliance to an ISC Master Server, as follows: Step 1 On the ISC device, go to the following directory: cd /<isc_install_directory>/thirdparty/rv/bin Step 2 Set up a TIBCO Listener to the TIBCO port that isc installation is running and as configured above (default: 7530): ./tibrvlisten -service <tibco_port_number> "cisco.cns.>" Leave the Listener running in this window. Step 3 In a separate window, telnet to the Cisco CNS IE2100 appliance. Step 4 Go to the following directory: cd /opt/CSCOcnsie/tools Step 5 Send a TIBCO message to the ISC Master server on the configured ISC installation port (default: 7530): ./cns-send -service <tibco_port_number> "cisco.cns.config-changed" "<variable_message>" Step 6 If the message is seen in the Listener window on the ISC Master server, connectivity is established correctly from the Cisco CNS IE2100 appliance to the ISC Master server for the TIBCO subject "cisco.cns.>". Step 7 If you are using Cisco CNS Configuration Engine Release 1.3.2 or 1.4, proceed with Step 8 to Step 12. Otherwise, proceed to the "Checking Router Configurations Overview" section." Step 8 In the window created in Step 1, set up a TIBCO Listener to the TIBCO port that isc installation is running and as configured above (default: 7530): ./tibrvlisten -service <tibco_port_number> "cisco.mgmt.cns.>" Leave the Listener running in this window. Step 9 In a separate window, telnet to the Cisco CNS IE2100 appliance. Step 10 Go to the following directory: cd /opt/CSCOcnsie/tools Step 11 Send a TIBCO message to the ISC Master server on the configured ISC installation port (default: 7530): ./cns-send -service <tibco_port_number> "cisco.mgmt.cns.config-changed" "<variable_message>" Step 12 If the message is seen in the Listener window on the ISC Master server, connectivity is established correctly from the Cisco CNS IE2100 appliance to the ISC Master server for the TIBCO subject "cisco.mgmt.cns.>". Checking Router Configurations Overview The Cisco IOS image is needed for the routers used with the Cisco CNS IE2100 functionality (that is, the CNS transport mechanism and/or the CNS Plug-and-Play feature). For Cisco CNS Configuration Engine Release 1.3, the recommended Cisco IOS release is 12.2(8)T or later; for Cisco CNS Configuration Engine Release 1.3.1, 1.3.2, or 1.4, the recommended Cisco IOS release is 12.2(11)T or later. Cisco IOS releases 12.3(1)T or later are supported only by Cisco CNS Configuration Engine Releases 1.3.2 and 1.4. Additionally, the router running a configuration must contain the following two CNS commands: 1. cns config partial <IE2100 address> 80 2. cns event <ie2100 address> 11011 or cns event <ie2100 address> 11011 keepalive <num. of seconds> <num. of trials> Note The keepalive option makes sure the TCP connection between the Cisco CNS IE2100 appliance and the router is alive at all times. It sends keepalive messages at <num. of seconds> intervals with <num. of trials> retries. Also, the router startup configuration must contain the following two CNS commands: 1. cns config initial <ie2100 address> event The cns config initial command should be configured in the startup configuration of the Cisco IOS device or router. It triggers the router to pick up and apply any initial configuration that might be waiting for it on the Cisco CNS IE2100 appliance. After the cns config initial command is executed, this command is automatically removed. The recommendation is to include the cns config partial command in the initial configuration that is waiting on the Cisco CNS IE2100 appliance. If a no persist option is used, the router does not perform a write-mem, thus keeping the startup configuration from being overwritten. 2. cns event <ie2100 address> 11011 or cns event <ie2100 address> 11011 keepalive <num. of seconds> <num. of trials> Note The keepalive option makes sure the TCP connection between the Cisco CNS IE2100 appliance and the router is alive at all times. It sends keepalive messages at <num. of seconds> intervals with <num. of trials> retries. Different IOS versions can support additional CNS commands or different formats of the same CNS command. See the Cisco CNS software documentation for more details on the other possible CNS commands and their options.
	Terms & Conditions \| Privacy Statement \| Cookie Policy \| Trademarks