Feedback
Contents
A through M
- aaa group server radius
- address-family
- aggregate-address
- apply profile
- autodiscovery bgp signaling ldp
- boot poap
- bridge-domain
- checkpoint
- clear evb
- clear evb statistics
- clear fabric access
- clear fabric connectivity cable-plan
- clear fabric connectivity neighbors
- clear fabric database statistics
- clear fabricpath oam loopback
- clear FabricPath oam mtrace
- clear fabripath oam notification
- clear fabricpath oam traceroute
- configure profile
- copy scheduled-config
- db-jid
- db-security
- db-table
- debug evb
- default-information originate
- define
- description (fabricpath-oam)
- dot1q (fabricpath-oam)
- encapsulation dot1Q
- errdisable detect cause
- errdisable recovery cause
- errdisable recovery interval
- ether-type (fabricpath-oam)
- evb mac
- evb reinit-keep-alive
- evb resource-wait-delay
- fabric access attach device
- fabric access attach group
- fabric access create group
- fabric access group
- fabric access local-help
- fabric access login
- fabric access ping
- fabric access prepend-id
- fabric access send device
- fabric access send group
- fabric access server
- fabric connectivity cable-plan enforce
- fabric connectivity cable-plan generate
- fabric connectivity cable-plan import
- fabric connectivity mismatch action delay
- fabric connectivity tier
- fabric database mobility-domain
- fabric database type
- fabric forwarding anycast-gateway-mac
- fabric forwarding control-segment
- fabric forwarding conversational-aging
- fabric forwarding conversational-learning
- fabric forwarding identifier
- fabric forwarding switch-role
- fabricpath isis bfd
- fabricpath oam profile
- feature cable-management
- feature evb
- feature fabric
- feature fabric access
- feature fabric multicast
- feature-set fabric
- feature vn-segment-vlan-based
- flow (fabricpath-oam)
- hop (fabricpath-oam)
- include profile
- install feature-set fabric
- instance
- interface (fabricpath-oam)
- ip (fabricpath-oam)
- ip arp rarp fabric-forwarding
- ip multicast fabric-forwarding
- ipv6 (fabricpath-oam)
- logging level evb
- mac-address (fabricpath-oam)
- match (VLAN access-map)
- mtrace fabricpath
aaa group server radius
To create a RADIUS server group and enter RADIUS server group configuration mode, use the aaa group server radius command in global configuration mode. To delete a RADIUS server group, use the no form of this command.
Syntax Description
group-name RADIUS server group name. The name is alphanumeric and case-sensitive. The maximum length is 64 characters.
Command History
Examples
The following example shows how to create a RADIUS server group and enter RADIUS server configuration mode:
Device# configure terminal Device(config)# aaa group server radius RadServer Device(config-radius)#
The following example shows how to delete a RADIUS server group:
Device# configure terminal Device(config)# no aaa group server radius RadServeraddress-family
To configure multicast VPN (MVPN) for IPv4 or IPv6, use the address-family command in router configuration mode or neighbor configuration mode. To disable MVPN configuration, use the no form of this command.
Syntax Description
ipv4 Configures the IPv4 address-family.
ipv6 Configures the IPv6 address-family.
mvpn Configures Multicast VPN .
Command History
Usage Guidelines
This command places the router in address family configuration mode (prompt: config-router-af), from which you can configure routing sessions that support Multicast VPN provisioning for IPv4 or IPv6.
Examples
The following example shows how to configure multicast VPN for IPv4:
Device> enable Device# configure terminal Device(config)# router bgp 100 Device(config-router)# address-family ipv4 mvpn Device(config-router-af)# exitThe following example shows how to configure multicast VPN for IPv6:
Device> enable Device# configure terminal Device(config)# router bgp 100 Device(config-router)# address-family ipv6 mvpn Device(config-router-af)# exitaggregate-address
To create a summary address in a Border Gateway Protocol (BGP) routing table, use the aggregate-address command. To remove the summary address, use the no form of this command.
aggregate-address address/length [ advertise-map map-name][as-set][ attribute-map map-name][summary-only][ suppress-map map-name]
no aggregate-address address/length [ advertise-map map-name][as-set][ attribute-map map-name][summary-only][ suppress-map map-name]
Syntax Description
address/length Specifies aggregate IP address and mask length. Valid values for length are as follows:
advertise-map map-name (Optional) Specifies the name of the route map used to select attribute information from specific routes.
as-set (Optional) Generates the autonomous system set path information and community information from the contributing paths.
attribute-map map-name (Optional) Specifies the name of the route map used to set the attribute information for specific routes. The map-name is an alphanumeric string up to 63 characters.
summary-only (Optional) Filters all more-specific routes from updates.
suppress-map map-name (Optional) Specifies the name of the route map used to conditionally filter more specific routes. The map-name is an alphanumeric string up to 63 characters.
Command Default
The atomic aggregate attribute is set automatically when an aggregate route is created with this command unless the as-set keyword is specified.
Command Modes
Address-family configuration mode
Neighbor address-family configuration mode
Router BGP configuration mode
Command History
Usage Guidelines
You can implement aggregate routing in BGP and mBGP either by redistributing an aggregate route into BGP or mBGP, or by using the conditional aggregate routing feature.
Using the aggregate-address command with no keywords will create an aggregate entry in the BGP or mBGP routing table if any more-specific BGP or mBGP routes are available that fall within the specified range. (A longer prefix which matches the aggregate must exist in the RIB.) The aggregate route will be advertised as coming from your autonomous system and will have the atomic aggregate attribute set to show that information might be missing. (By default, the atomic aggregate attribute is set unless you specify the as-set keyword.)
Using the as-set keyword creates an aggregate entry using the same rules that the command follows without this keyword, but the path advertised for this route will be an AS_SET consisting of all elements contained in all paths that are being summarized. Do not use this form of the aggregate-address command when aggregating many paths, because this route must be continually withdrawn and updated as autonomous system path reachability information for the summarized routes changes.
Using the summary-only keyword not only creates the aggregate route (for example, 192.*.*.*) but also suppresses advertisements of more-specific routes to all neighbors. If you want to suppress only advertisements to certain neighbors, you may use the neighbor distribute-list command, with caution. If a more-specific route leaks out, all BGP or mBGP routers will prefer that route over the less-specific aggregate you are generating (using longest-match routing).
Using the suppress-map keyword creates the aggregate route but suppresses advertisement of specified routes. You can use the match clauses of route maps to selectively suppress some more-specific routes of the aggregate and leave others unsuppressed. IP access lists and autonomous system path access lists match clauses are supported.
Using the advertise-map keyword selects specific routes that will be used to build different components of the aggregate route, such as AS_SET or community. This form of the aggregate-address command is useful when the components of an aggregate are in separate autonomous systems and you want to create an aggregate with AS_SET, and advertise it back to some of the same autonomous systems. You must remember to omit the specific autonomous system numbers from the AS_SET to prevent the aggregate from being dropped by the BGP loop detection mechanism at the receiving router. IP access lists and autonomous system path access lists match clauses are supported.Using the attribute-map keyword allows attributes of the aggregate route to be changed. This form of the aggregate-address command is useful when one of the routes forming the AS_SET is configured with an attribute such as the community no-export attribute, which would prevent the aggregate route from being exported. An attribute map route map can be created to change the aggregate attributes.
This command requires the Enterprise Services license.
Examples
AS-Set Example
In This example, an aggregate BGP address is created in router configuration mode. The path advertised for this route will be an AS_SET consisting of all elements contained in all paths that are being summarized.
Device(config)# router bgp 64496 Device(config-router)# aggregate-address 10.0.0.0 255.0.0.0 as-setSummary-Only Example
In This example, an aggregate BGP address is created in address family configuration mode and applied to the multicast database (SAFI) under the IP Version 4 address family. Because the summary-only keyword is configured, more-specific routes are filtered from updates.
Device(config)# router bgp 64496 Device(config-router)# address-family ipv4 multicast Device(config-router-af)# aggregate-address 10.0.0.0 255.0.0.0 summary-onlyConditional Aggregation Example
In This example, a route map called MAP-ONE is created to match on an as-path access list. The path advertised for this route will be an AS_SET consisting of elements contained in paths that are matched in the route map.
Device(config)# ip as-path access-list 1 deny ^1234_ Device(config)# ip as-path access-list 1 permit .* Device(config)# ! Device(config)# route-map MAP-ONE Device(config-route-map)# match ip as-path 1 Device(config-route-map)# exit Device(config)# router bgp 64496 Device(config-router)# address-family ipv4 Device(config-router-af)# aggregate-address 10.0.0.0 255.0.0.0 as-set advertise-map MAP-ONE Device(config-router-af)# endapply profile
To apply a configuration profile to configure hosts, use the apply profile command in global configuration mode. To remove the configuration profile use the no form of this command.
apply profile profile-name [ include-instance include-instance ] [ param-instance instance-name ]
no apply profile profile-name [ include-instance include-instance ] [ param-instance instance-name ]
Syntax Description
profile-name Name of the profile that is created using the configure profile command.
include-instance include-instance (Optional) Specifies the include instance name.
param-instance instance-name (Optional) Specifies the parameter instance name.
Command History
Usage Guidelines
Configuration profiles provide an infrastructure to configure hosts based on a set of user-defined templates. You can define different templates for different types of hosts and enable them appropriately based on an event, such as host discovery. You can apply different profiles to different hosts and apply different values for the configuration for different hosts.
Use the apply profile command to apply a configuration profile on a host.
Use the configure profile command to create a configuration profile and add a parameter list and a parameter-list instance. You can either create one parameterized profile for each host or create one profile with parameterized argument and apply it with host-specific arguments. The parameter-list instance provides the actual values that are added in the configuration profile before the profile is applied. The parameter name in the instance must match the parameter name in the profile.
Examples
The following example shows how to create a configuration profile and apply it to a host instance, named HOST-1, to expand the profile and configure a new host:
Device(config)# configure profile sample Device(conf-profile)# vlan $vlanId Device(conf-profile-vlan)# vn-segment $segmentId Device(conf-profile-vlan)# interface vlan $vlanId Device(conf-profile-if-verify)# ip address $ipv4addr/$netmask1 Device(conf-profile-if-verify)# ipv6 address $ipv6addr/$netmask2 Device(conf-profile-if-verify)# ip access-group $aclnum out Device(conf-profile-if-verify)# configure terminal Device(config)# apply profile sample param-instance HOST-1 Device(config)# end
Related Commands
Command
Description
Related Information
Configures a profile.
autodiscovery bgp signaling ldp
To enable autodiscovery using Label Distribution Protocol (LDP) in a Layer 2 virtual forwarding interface (VFI), use the autodiscovery bgp signaling ldp command in L2 VFI configuration mode. To disable autodiscovery, use the no form of this command.Command History
Examples
The following example shows how to enable Layer 2 VFI as having BGP autodiscovered pseudowire members and specify that LDP signaling should be used for autodiscovery:
Device(config)# l2vpn vfi context vfi1 Device(config-vfi)# vpn id 100 Device(config-vfi)# autodiscovery bgp signaling ldp Device(config-vfi-autodiscovery)#boot poap
To reboot a device and apply the changes after you configure the device or install a new image, use the boot poap command in global configuration mode. To avoid rebooting the device, use the no form of this command.
Related Commands
Command
Description
Related Information
Configures a file that contains CLI commands and applies on the next reboot of the device.
bridge-domain
To enter bridge-domain configuration mode and configure a bridge domain, use the bridge-domain command. To remove the bridge-domain configurations, use the no form of this command.Syntax Description
domain-id Specifies the Bridge-domain ID. The range is defined by the system-bridge-domain configuration.
Command History
Usage Guidelines
Removing the bridge-domain configuration does not remove the underlying VLAN. If a VLAN is associated with a bridge domain, you cannot remove the VLAN without first removing the bridge domain. To remove the underlying VLAN, use the no vlan command after you remove the bridge domain. This command requires the MPLS Services license.
checkpoint
To configure the rollback checkpoint, use the checkpoint command. To delete the checkpoint, use the no form of this command.
Syntax Description
name
Specifies the checkpoint name that is used in the checkpoint database. The name can contain any alphanumeric string up to 80 characters, without any spaces.
description description
Specifies the checkpoint description. The description can contain up to 80 alphanumeric characters, including space.
file name
Specifies the filename that is used to save the checkpoint. clear evb
To clear information associated with Edge Virtual Bridging (EVB), use the clear evb command in global configuration mode.
clear evb { hosts | vsi } [force-standby] [ interface ethernet slot-number ] [ ip ipv4-address ] [ ipv6 ipv6-address ] [ mac mac-address ] [ vlan vlan-id ] [ vni vni-id ]
Syntax Description
hosts Clears information about hosts in an EVB session.
vsi Clears information about the Virtual Station Interface (VSI) in an EVB session.
force-standby (Optional) Forces to clear standby entries in an EVB session.
interface ethernet slot-number (Optional) Clears hosts or VSI entries by filtering interface.
ip ipv4-address (Optional) Clears information about hosts or the VSI by filtering the IPv4 address.
ipv6 ipv6-address (Optional) Clears information about hosts or the VSI by filtering the IPv6 address.
mac mac-address (Optional) Clears information about hosts or the VSI by filtering the MAC address.
vlan vlan-id (Optional) Clears information about hosts or the VSI by filtering the VLAN.
vni vni-id (Optional) Clears information about hosts or the VSI by filtering the Virtual Network Identifier (VNI).
Command History
Related Commands
Command
Description
Related Information
Enables the EVB session on a device.
Clears Edge Virtual Bridge (EVB) statistic counters.
clear evb statistics
To clear Edge Virtual Bridge (EVB) statistic counters, use the clear evb statistics command in global configuration mode.
Command History
Related Commands
Command
Description
Related Information
Clears information associated with Edge Virtual Bridging (EVB).
Enables the EVB session on a device.
clear fabric access
To clear specific user sessions and disconnect specific user from the Extensible Messaging and Presence Protocol (XMPP) server, or to clear fabric access statistics, use the clear fabric access command in privileged EXEC mode.
Syntax Description
statistics Clears user statistics such as ping parameters.
user username Clears the specified user connection.
Command History
Related Commands
Command
Description
Related Information
Attaches a remote device in the fabric network to an XMPP server.
Attaches a group of devices in the fabric network to an XMPP server.
Creates one or more groups of devices on the fabric access network using the XMPP server.
clear fabric connectivity cable-plan
To clear the current cable plan, use the clear fabric connectivity cable-plan command in privileged EXEC mode.
Command History
Usage Guidelines
Before you import a new cable plan, use this command to clear the existing one.
To clear a cable plan that is already saved to the startup configuration, specify this command and then configure the copy running-config startup-config command.
Examples
The following example shows how to clear an existing cable plan:
Device(config)# feature lldp Device(config)# feature cable-management Device(config)# exit Device# fabric connectivity cable-plan import bootflash:cp.xml Success: Imported cable-plan: /bootflash/cp.xml Device# clear fabric connectivity cable-planclear fabric connectivity neighbors
To clear all information about neighbors or subset of neighbors from the neighbor cache, use the clear fabric connectivity neighbors command in privileged EXEC mode.
clear fabric connectivity neighbors [ interface { ethernet slot-number/port-number | mgmt interface-number } | stale ]
Syntax Description
interface (Optional) Clears cache of neighbors connected to an interface.
ethernet (Optional) Specifies the Ethernet interface.
slot-number/port-number (Optional) Slot number and port number.
mgmt interface-number (Optional) Specifies the management interface and the interface number.
stale (Optional) Clears neighbor cache information for stale or purged neighbors.
Command History
Usage Guidelines
Use this command to delete a single entry, all entries, or all error entries from the network neighbor cache. You should manually clear an already secured port in the neighbor cache if recabling is desired to immediately remove old or stale entries. If you have a switch that was previously in the network but has since gone stale (because it was removed or taken down), the only way to completely remove it from the neighbor cache is by using this command. You have to enable the cable management feature using the feature cable-management command to be able to use the clear fabric connectivity neighbors command.
Related Commands
Command
Description
Related Information
Enables automatic recovery of an application from an error-disabled state.
Imports a cable plan from a local or a remote location.
Delays the port error-disable action on detecting cabling errors for a specified time.
Configures the tier level of a device.
clear fabric database statistics
To clear the external database statistics such as number of messages sent or received, pending requests, access errors, and access timeouts, use the clear fabric database statistics command in privileged EXEC mode.
Using LDAP or RADIUS
clear fabric database statistics [ type { network | cabling | profile } [ server-proto { ldap | radius } { host hostname | ip ip-address } [ port port-number ] ] ]
Using XMPP
clear fabric database statistics [ type { network | cabling | profile } [ server-proto xmpp { host hostname | ip ip-address } [ port port-number ] db-jid jid ] ]
Syntax Description
type (Optional) Specifies the type of database.
network (Optional) Specifies a network database.
cabling (Optional) Specifies a cable management database.
profile (Optional) Specifies a port or switch profile database.
server-proto (Optional) Specifies a database protocol.
ldap (Optional) Specifies the use of Lightweight Directory Access Protocol (LDAP).
radius (Optional) Specifies the use of RADIUS.
xmpp (Optional) Specifies the use of Extensible Messaging and Presence Protocol (XMPP).
host hostname (Optional) Specifies the hostname of the server.
ip ip-address (Optional) Specifies the IP address of the server.
port port-number (Optional) Specifies the port number of the server.
db-jid jid (Optional) Specifies the Jabber ID of the database.
Command History
Usage Guidelines
The clear fabric database statistics command is used to reset the database statistics counters to zero. But this command does not delete existing statistics memory. You can use the show fabric database statistics command to display per-server statistics including number of messages sent or received, pending requests, access errors, and timeouts.
Related Commands
Command
Description
Related Information
Displays fabric database statistics.
clear fabricpath oam loopback
To clear information about FabricPath Operation, Administration, and Maintenance (OAM) loopback, use the clear fabricpath OAM loopback command in privileged EXEC mode.
clear fabricpath oam loopback { database [ session session-handle ] | session session-handle | statistics [ session session-handle | summary ] }
Syntax Description
database Clears information about FabricPath OAM loopback database.
session session-handle Clears information about the FabricPath OAM loopback for a specific session.
statistics Clears information about FabricPath OAM loopback statistics.
summary Clears summary information about fabricpath OAM loopback statistics.
Command History
Usage Guidelines
To clear statistics for all sessions, use the clear fabricpath oam loopback statistics command. To clear statistics for a particular session, use the clear fabricpath oam loopback statistics session command. To clear summary statistics, use the clear fabricpath oam loopback statistics summary command.
Related Commands
Command
Description
Related Information
Shows statistics for FabricPath OAM loopback.
clear FabricPath oam mtrace
To clear information about FabricPath Operation, Administration, and Maintenance (OAM) mtrace, use the clear fabricpath oam mtrace command in privileged EXEC mode.
Syntax Description
database Clears information about the FabricPath OAM mtrace database.
session session-handle (Optional) Clears information about the FabricPath OAM mtrace for a specific session.
statistics Clears FabricPath OAM mtrace statistics.
summary (Optional) Clears FabricPath OAM mtrace statistics summary.
Command History
Related Commands
Command
Description
Related Information
Shows statistics for fabricpath OAM mtrace.
clear fabripath oam notification
To clear information about FabricPath Operation, Administration, and Maintenance (OAM) notification, use the clear fabricpath oam notification command in privileged EXEC mode.
Syntax Description
database Clears information about FabricPath OAM notification database.
statistics Clears information about FabricPath OAM notification statistics.
Command History
Related Commands
Command
Description
Related Information
Shows information about for FabricPath OAM notification.
clear fabricpath oam traceroute
To clear information about FabricPath Operation, Administration, and Maintenance (OAM) traceroute, use the clear fabricpath oam traceroute command in privileged EXEC mode.
Syntax Description
database Clears information about FabricPath OAM traceroute database.
session session-handle (Optional) Clears information about for FabricPath OAM traceroute for a specific session.
statistics Clears FabricPath OAM traceroute statistics.
summary (Optional) Clears FabricPath OAM traceroute statistics summary.
Command History
Related Commands
Command
Description
Related Information
Shows statistics for FabricPath OAM traceroute.
configure profile
To configure a profile, use the configure profile command in privileged EXEC mode. To remove a configured profile, use the no form of this command.
Syntax Description
Command History
Usage Guidelines
You can specify a maximum of 80 characters for the profile-name argument. Once you configure a profile name, this profile is available in the list of profiles that can be used to configure profile parameters. Use the show running-config command to display all configured profiles and their parameters.
When you configure a profile, the command mode changes to configuration profile mode. You can configure profile parameters into a template in the configuration profile mode.
Use the show config-profile command to view the list of configured profiles.
Examples
The following example shows how to configure a profile named pname:
Device# configure profile pname Device(config-profile)#The following example shows how to configure profile parameters in the configuration profile mode:
Device# configure profile sample Device(config-profile)# vrf context sample-vrf Device(config-profile-vrf)# endcopy scheduled-config
To configure a file containing CLI commands that you want to apply on the next reboot of the device, use the copy scheduled-config command in any command mode.
Usage Guidelines
The copy scheduled-config command specifies the schedule of the configuration at the specified source to apply on the next reboot of the device. This command must be called explicitly within the POAP (Power On Auto Provisioning) script to allow the POAP boot process to continue at the next reboot. When PowerOn Auto Provisioning (POAP) is in progress, any important information or errors are displayed over the serial console, aiding the administrator to troubleshoot in case of problems.
This command does not require a license.
Note
This command is used in POAP script.db-jid
To configure the Jabber ID of the database using Extensible Messaging and Presence Protocol (XMPP), use the db-jid command in fabric database server configuration mode. To remove the Jabber ID of the database, use the no form of this command.
Syntax Description
jid Jabber ID of the database.
key-type key-type-value (Optional) Specifies the key type for the database queries. The valid value is 1.
Command History
Related Commands
Command
Description
db-security
To configure a database security, use the db-security command in fabric database server configuration mode.
db-table user username password password [ shared-secret name ]
no db-table user username password password [ shared-secret name ]
Syntax Description
Command History
Examples
device# configure device(config)# fabric database type network device(config-fabric-db)# server protocol ldap host host1 device(config-fabric-db-server)# db-table ou=networks,dc=host,dc=com key-type 1 device(config-fabric-db-server)# db-security user cn=admin,dc=cisco,dc=com password cisco123
Related Commands
Command
Description
db-table
To configure a database table using Lightweight Directory Access Protocol (LDAP), use the db-table command in fabric database server configuration mode. To remove the database table, use the no form of this command.
Syntax Description
table-name Name of the database table.
key-type key-type-value (Optional) Specifies the key type for the database queries. The valid value is 1.
Command History
Related Commands
Command
Description
Related Information
Configures the Jabber ID of the database using XMPP.
debug evb
To enable debugging of events associated with an Edge Virtual Bridging (EVB) session, use the debug evb command in privileged EXEC mode. To disable debugging, use the no form of this command.
debug evb { all | cli | errors | events | ha | periodic | pss | trace | verbose }
no debug evb { all | cli | errors | events | ha | periodic | pss | trace | verbose }
Syntax Description
all Enables debugging of all events in an EVB session.
cli Enables debugging of CLI command processing events only.
errors Enables debugging of only errors in an EVB session.
events Enables debugging of only general events in an EVB session.
ha Enables debugging of only High Availability (HA) related events in an EVB session.
periodic Enables debugging of only periodic events in an EVB session.
pss Enables debugging of only persistent storage service (PSS) related events in an EVB session.
trace Enables debugging of detailed processing traces in an EVB session.
verbose Enables debugging of verbose mode in an EVB session.
Command History
Usage Guidelines
Use the feature evb command to enable the EVB session. This, in turn, enables the debug evb command on the device.
Examples
The following example shows how to enable debugging of detail processing traces in an EVB session:
Device# configure terminal Device(config)# feature evb Device(config)# end Device# debug evb errors eventsThe following is sample output from the show debug evb command in an EVB session:
Device# show debug evb Debugs Enabled: errors eventsdefault-information originate
To configure a Border Gateway Protocol (BGP) routing process to distribute a default route (network 0.0.0.0), use the default-information originate command in address family configuration mode. To disable the advertisement of a default route, use the no form of this command.
Command History
Related Commands
Command
Description
Related Information
Configures multicast VPN.
define
To create user-defined parameters for a parameter list, use the define command in parameter list configuration mode. To remove user-defined parameters from a parameter list, use the no form of this command.
define parameter-name [ integer| ipaddr| ipv6addr| mac-addr| string] [ value]
no define parameter-name [ integer| ipaddr| ipv6addr| mac-addr| string] [ value]
Syntax Description
parameter-name Parameter name.
integer (Optional). Specifies the data type as an integer.
ipaddr (Optional). Specifies the address as an IPv4 address.
ipv6addr (Optional). Specifies the address as an IPv6 address.
mac-addr (Optional). Specifies the address as a MAC address.
string (Optional). Specifies the data type as a string.
value (Optional). Parameter data type or address type value or parameter description.
Command History
Usage Guidelines
User-defined parameters that you create using the define command are associated with a parameter list. A parameter list can be created using the param-list command.
You can use existing user-defined parameters and associate values (such as integer, IP address, and MAC address) to them.
Related Commands
Command
Description
Related Information
Configures a parameter list instance.
description (fabricpath-oam)
To configure a description for a FabricPath Operation, Administration, and Maintenance (OAM) profile, use the description command in FabricPath OAM profile configuration mode. To remove the FabricPath OAM profile description, use the no form of this command.
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Configures a FabricPath OAM profile.
dot1q (fabricpath-oam)
To specify that a FabricPath Operation, Administration, and Maintenance (OAM) flow profile must include a dot1q tag, use the dot1q command in FabricPath oam flow profile configuration mode. To remove the dot1q tag, use the no form of this command.
Syntax Description
vlan-id Specifies the flow profile VLAN ID.
cos service-value (Optional) Specifies the class of service (CoS). The range is from 0 to 7.
Command History
Related Commands
Command
Description
Related Information
Configures a FabricPath OAM profile.
Configures the direction FabricPath OAM flow entropy.
encapsulation dot1Q
To enable IEEE 802.1Q encapsulation of traffic on a specified subinterface in a virtual LAN (VLAN), use the encapsulation dot1q command. To disable encapsulation, use the no form of this command.Syntax Description
vlan-id Specifies the VLAN to set when the interface is in access mode. The range is from 1 to 4094 except for the VLANs reserved for internal switch use.
Command History
Usage Guidelines
IEEE 802.1Q encapsulation is configurable on Ethernet interfaces. IEEE 802.1Q is a standard protocol for interconnecting multiple switches and routers and for defining VLAN topologies.
Use the encapsulation dot1q command in subinterface range configuration mode to apply a VLAN ID to the subinterface.
This command does not require a license.
errdisable detect cause
To enable error-disable (errdisable) detection for an application, use the errdisable detect cause command in global configuration mode. To disable error-disable detection, use the no form of this command.errdisable detect cause { acl-exception | all | link-flap | loopback | miscabling }
no errdisable detect cause { acl-exception | all | link-flap | loopback | miscabling }
Syntax Description
acl-exception Enables error-disabled detection for access-list installation failures.
all Enables error-disabled detection for all causes.
link-flap Enables error-disabled detection on link-state flapping.
loopback Enables error-disabled detection on loopback detected by unidirectional link detection (UDLD).
miscabling Enables error-disabled detection on a miscabled port.
Command History
Related Commands
Command
Description
Related Information
Enables automatic recovery of an application from an error-disabled state.
Configures the error disable recovery timer.
Imports a cable plan from a local or a remote location.
Displays information about interfaces that are in error-disabled state.
errdisable recovery cause
To enable automatic recovery of an application from an error-disabled (errdisable) state, use the errdisable recovery cause command in global configuration mode. To return to the default setting, use the no form of this command.
errdisable recovery cause { all | bpduguard | failed-port-state | link-flap | loopback | miscabling | psecure-violation | security-violation | storm-control | udld | vpc-peerlink }
errdisable recovery cause { all | bpduguard | failed-port-state | link-flap | loopback | miscabling | psecure-violation | security-violation | storm-control | udld | vpc-peerlink }
Syntax Description
all Enables the timer to recover from all causes.
bpduguard Enables the timer to recover from the bridge protocol data unit (BPDU) guard error disable state.
failed-port-state Enables the timer to recover from the Spanning Tree Protocol (STP) set port state failure.
link-flap Enables the timer to recover from link-state flapping.
loopback Enables timer to recover from the loopback error disabled state detected by Unidirectional Link Detection (UDLD).
miscabling Enables the timer to automatically recover miscabled ports from an error-disabled state.
psecure-violation Enables the timer to recover from the psecure-violation disable state.
security-violation Enables the timer to recover from the 802.1x violation disable state.
storm-control Enables the timer to recover from the storm control error-disabled state.
udld Enables the timer to recover from the UDLD error-disabled state.
vpc-peerlink Enables the timer to recover from an inconsistent virtual port channel (vPC) peer-link error-disabled state.
Command History
Release Modification — This command was introduced in a release earlier than Cisco NX-OS Release 7.0(0)N1(1). 7.0(0)N1(1)
This command was modified. The miscabling keyword was added.
Usage Guidelines
Use the errdisable recovery cause command to enable an automatic recovery of an application on the interface from an error-disabled state. This command tries to bring the interface out of the error-disabled state once all the causes have timed out. The interface automatically tries to come up again after 300 seconds. To change this interval, use the errdisable recovery interval command.
This command does not require a license.
Related Commands
Command
Description
Related Information
Enables error-disable detection for an application.
Configures the error disable recovery timer.
Imports a cable plan from a local or a remote location.
Displays information about interfaces that are in error-disabled state.
errdisable recovery interval
To configure the error disable recovery timer, use the errdisable recovery interval in global configuration mode. To remove this configuration, use the no form of this command.
Syntax Description
Command History
Release Modification — This command was introduced in a release earlier than Cisco NX-OS Release 7.0(0)N1(1).
Related Commands
Command
Description
Related Information
Enables error-disable detection for an application.
Enables automatic recovery of an application from an error-disabled state.
Imports a cable plan from a local or a remote location.
Displays information about interfaces that are in error-disabled state.
ether-type (fabricpath-oam)
To configure the FabricPath Operation, Administration, and Maintenance (OAM) flow profile ether-type, use the ether-type command in FabricPath OAM flow profile configuration mode. To remove the ether-type, use the no form of this command.
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Configures a FabricPath OAM profile.
evb mac
To configure the Virtual Station Interface (VSI) Discovery and Configuration Protocol (VDP) multicast MAC address for the Edge Virtual Bridge (EVB) feature on a device, use the evb mac command in global configuration mode. To return to the default, use the no form of this command.
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Enables the EVB session on a device.
evb reinit-keep-alive
To configure the Virtual Station Interface (VSI) Discovery and Configuration protocol (VDP) keepalive parameter for the Edge Virtual Bridging (EVB) feature on a device, use the evb reinit-keep-alive command in global configuration mode. To return to the default, use the no form of this command.
Syntax Description
Command History
Usage Guidelines
Use the feature evb command to enable the EVB feature globally on the device before configuring the keepalive parameter. After a VDP request is successful, a refresh request is expected within the keep-alive time. If the refresh request is not received within the keepalive time, device revokes the configuration changes. You must configure the correct reinit-keepalive EVB parameter to align with the network scale as each virtual machine contributes a refresh message as per the keepalive time.
Related Commands
Command
Description
Related Information
Configures the resource wait delay parameter for EVB.
Enables the EVB session on a device.
evb resource-wait-delay
To configure the Virtual Station Interface (VSI) Discovery and Configuration protocol (VDP) resource wait delay parameter for the Edge Virtual Bridge (EVB) feature on a device, use the evb resource-wait-delay command in global configuration mode. To return to the default, use the no form of this command.
Syntax Description
Command History
Usage Guidelines
Use the feature evb command to enable the EVB feature globally on the device before configuring the resource wait delay parameter.
When a VDP request is received, a series of configuration changes are triggered on the device. The resource-wait-delay parameter indicates the maximum waiting time for a device to complete the configuration change. If the change is not completed within the wait delay parameter, then the VDP request fails. You can configure the resource-wait-delay EVB parameter to align with specific configuration scale and requirement.
Related Commands
Command
Description
Related Information
Configures the keepalive parameter for EVB.
Enables the EVB session on a device.
fabric access attach device
To attach a remote device in the fabric network to an Extensible Messaging and Presence Protocol (XMPP) server, use the fabric access attach device command in privileged EXEC mode.
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Clears specific user sessions and disconnect a specific user from the XMPP server, or clears fabric access statistics.
Attaches a group of devices in the fabric network to an XMPP server.
Creates one or more groups of devices on the fabric access network using the XMPP server.
fabric access attach group
To attach a group of devices in the fabric network to an Extensible Messaging and Presence Protocol (XMPP) server, use the fabric access attach group command in privileged EXEC mode.
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Clears specific user sessions and disconnect a specific user from the XMPP server, or clears fabric access statistics.
Attaches a remote device in the fabric network to an XMPP server.
Attaches a group of devices in the fabric network to an XMPP server.
Creates one or more groups of devices on the fabric access network using the XMPP server.
fabric access create group
To create one or more groups of devices on the fabric access network using the Extensible Messaging and Presence Protocol (XMPP) server, use the fabric access create group command in privileged EXEC mode. To remove one or more groups of devices from the fabric access network, use the no form of this command.
fabric access create group group-name1 [group-name2, group-name3...]
no fabric access create group group-name1 [group-name2, group-name3...]
Syntax Description
group-name1 Name of the group of devices.
[group-name2, group-name3...] [Optional] Names of additional groups.
Command History
Related Commands
Command
Description
Related Information
Clears specific user sessions and disconnect a specific user from the XMPP server, or clears fabric access statistics.
Attaches a remote device in the fabric network to an XMPP server.
fabric access group
To configure a group to which the switch needs to join or subscribe to in a fabric access network, use the fabric access group command in global configuration mode. To remove the switch from a group, use the no form of this command.
Syntax Description
group-name-1 Name of the group to which the switch needs to join or subscribe to.
[group-name-2, group-name-3, ...] (Optional) Name of the additional groups.
Command History
Related Commands
Command
Description
Related Information
Gets the online command syntax help using the currently logged-in switch.
Logs in to a fabric access server.
fabric access local-help
To get the online command syntax help using the currently logged-in local switch instead of remote switches accessed via the fabric access group chat, use the fabric access local-help command in privileged EXEC mode. To disable the online help on the currently logged-in local switch, use the no form of this command.
Command Default
Online help is not enabled for the currently logged-in local switch in the fabric access group chat mode.
Command History
Usage Guidelines
Online help can be used to find the available options after typing in a keyword. By default, online help is executed on the remote devices that generate several keyword options for each device in a network. To retrieve only those keywords related to the currently logged in device, the fabric access local-help command is used.
fabric access login
To log in to the fabric access server, use the fabric access login command in privileged EXEC mode. To log out of the server, use the no form of this command.
Syntax Description
password Password for users to log in to the fabric access server. A password can contain any combination of alphanumeric characters.
Command History
Related Commands
Command
Description
Related Information
Gets the online command syntax help using the currently logged-in switch.
Configures a group to which the switch needs to join or subscribe to in a fabric access network.
fabric access ping
To check the network reachability of the switch to the fabric access server and to enable the Extensible Messaging and Presence Protocol (XMPP) ping, use the fabric access ping command in global configuration mode. To disable the ping, use the no form of this command.
Syntax Description
interval seconds (Optional) Specifies the frequency of XMPP ping messages that are sent out. The default interval is 60 seconds. The range is from 30 to 180.
response seconds (Optional) Specifies the expected time to receive a ping response from the fabric access server. The default response value is 10 seconds. The range is from 3 to 30.
retry time (Optional) Specifies the number of ping messages that are sent without receiving a successful response from the fabric access server. The default retry value is 5. The range is from 1 to 5.
Command History
Related Commands
Command
Description
Related Information
Configures a group to which the switch needs to join or subscribe to in a fabric access network.
fabric access prepend-id
To enable the display of the device ID in the response message of a remote device in the fabric access group chat, use thefabric access prepend-id command in global configuration mode. To remove the device ID in the response message, use the no form of this command.
Command History
Related Commands
Command
Description
Related Information
Configures a group to which the switch needs to join or subscribe to in a fabric access network.
fabric access send device
To send a command to a host device or a list of host devices without entering the fabric access group chat mode, use the fabric access send device command in privileged EXEC mode.
Syntax Description
device-jid The Jabber ID (JID) of the single peer device to be addressed. Multiple device JIDs (device-jid2...device-jidn ) can also be specified.
“cli-command” Command History
Usage Guidelines
To ensure the remote device is in the correct mode to accept the command(s), start the message to be sent with an “end” keyword followed by a space, semicolon, and the command. If there are multiple commands to be sent, each command should be separated by a space and semicolon.
Examples
The following example shows how to send a command to a host device with the JID p3-ac13-64t to enable “feature lldp” on that device:
Device(config)# fabric access send device p3-ac13-64t “end; conf; feature lldp”The following example shows how to send a command to “show host name” on a list of host devices with the JIDs p1-sp1-48p, p1-sp2-48p, and p3-ac13-64t:
Device(config)# fabric access send device p1-sp1-48p p1-sp2-48p p3-ac13-64t “show hostname”
Related Commands
Command
Description
Related Information
Sends a CLI command to a group of devices without entering fabric access group chat mode.
fabric access send group
To send a CLI command to a group of devices without entering fabric access group chat mode, use the fabric access send group command in EXEC mode.
Syntax Description
group-name Name of the group in the fabric access network to which messages are sent.
"cli-command"
Note The CLI command must be within quotation marks. Command History
Usage Guidelines
Use the fabric access send group command to send CLI commands to a group in a fabric access network without entering fabric access group chat mode.
Note
You need to enable the fabric access feature to use the fabric access send group command. Use the feature fabric access command to enable fabric access on a device.
Related Commands
Command
Description
Related Information
Enables the fabric access feature for a fabric network.
Sends a command to a host device or a list of host devices without entering the fabric access group chat mode.
fabric access server
To configure the fabric access server to be connected to from a device, use the fabric access server command in global configuration mode. To disconnect the device from the fabric access server, use the no form of this command.
fabric access server dns-name [ vrf { vrf-name | default | management } ] [ device device-name ] [ password password-name ]
no fabric access server
Syntax Description
dns-name Fabric network server domain name.
vrf (Optional) Configures virtual routing and forwarding (VRF) information for a fabric access server.
vrf-name (Optional) Name of the VRF.
default (Optional) Configures the default VRF name.
management (Optional) Configures the management VRF name.
device (Optional) Configures the device in the fabric network.
device-name (Optional) Name of the device to be configured in the fabric network.
password (Optional) Configures the password for a device in the fabric network.
password-name (Optional) Password for the device.
Command History
Usage Guidelines
Use the fabric access server command to configure the fabric access server to be connected from the device that needs to be added to the fabric network. You need to configure the device name and password for the device in the fabric access server. The device name has to be a unique name in the network on a fabric access server.
Note
You need to enable the fabric access feature to access and view the fabric access server command. Use the feature fabric access command to enable the fabric access feature on a device.
Related Commands
Command
Description
Related Information
Enables the fabric access feature for a fabric network.
Displays the connection status of a device or a user that is connected in the fabric access network.
fabric connectivity cable-plan enforce
To enforce an imported cable plan, use the fabric connectivity cable-plan enforce command in global configuration mode. To stop enforcing a cable plan, use the no form of this command.
Command History
Usage Guidelines
When the fabric connectivity cable-plan enforce command is configured, all type, length, value (TLV) fields received on a device are checked against the enforced cable plan. If no cable plan is enforced, checks are ignored.
After importing a cable plan if the cable plan is not enforced or if the no fabric connectivity cable-plan enforce command is configured, all cable plan checks are disabled. However, the imported cable plan will remain in the device.
Use the show fabric connectivity cable-plan command to view the currently enforced cable plan.
Related Commands
Command
Description
Related Information
Enables the cable management feature for a network
fabric connectivity cable-plan generate
To automatically generate a cable plan based on the topology of the data center neighbors, use the fabric connectivity cable-plan generate command in privileged EXEC mode.
Syntax Description
Command History
Usage Guidelines
The fabric connectivity cable-plan generate command creates a valid cable plan from the output of the show fabric connectivity neighbors command. You can modify the autogenerated cable plan to suit the link or connectivity endpoints within your data center.
If you do not specify a plan-name, then the filename is a generic time-stamped name.
Note
Before configuring this command you must enable the feature lldp command and then the feature cable-management command in global configuration mode.
Related Commands
Command
Description
Related Information
Enables the cable management feature for a network
Displays cache information about fabric connectivity neighbors.
fabric connectivity cable-plan import
To import a cable plan from a local or a remote location, use the fabric connectivity cable-plan import command in privileged EXEC mode.
fabric connectivity cable-plan import [ ftp: | scp: | sftp: | tftp: ] bootflash: [ vrf vrf-name ] [ update ] [ verbose ]
Syntax Description
ftp: (Optional) Imports a cable plan from a remote FTP location.
scp: (Optional) Imports a cable plan from a remote Secure Copy Protocol location.
sftp: (Optional) Imports a cable plan from a remote Secure FTP location.
tftp: (Optional) Imports a cable plan from a remote TFTP location.
bootflash: Imports a cable plan from the local location.
vrf vrf-name (Optional) Displays information about the specified virtual routing and forwarding instance.
update (Optional) Updates the existing cable plan with a newly imported cable plan.
verbose (Optional) Prints all errors regarding the cable plan file import to the console.
Command History
Usage Guidelines
When you copy a cable plan from a remote location, you must specify the local location to save the file. If a remote import fails, the downloaded file is deleted automatically.
Once you configure the command, you have to enter the name of the source cable plan file and the destination cable plan file.
When you specify the fabric connectivity cable-plan import bootflash: command, the local cable plan file that exists in the bootflash is imported. Imported cable plans are stored in the device memory. Once imported, cable plans are persistent across reboots if you configure the copy running-config startup-config command.
Examples
The following example shows how the cp.xml file is imported from the local location:
Device# fabric connectivity cable-plan import bootflash:cp.xml Success: Imported cable-plan: /bootflash/cp.xml Device#The following sample output from the fabric connectivity cable-plan import bootflash: verbose command displays cable plan import failures:
Device# fabric connectivity cable-plan import bootflash:cp_failure.xml verbose /bootflash/cp_failure.xml:6: element LINK_INFO: Schemas validity error : Element '{http://www.cisco.com/cableplan/Schema2}LINK_INFO', attribute 'destPort': [facet 'pattern'] The value 'Eth11' is not accepted by the pattern 'Eth[0-9]{1,3}/[0-9]{1,3}'. /bootflash/cp_failure.xml:6: element LINK_INFO: Schemas validity error : Element '{http://www.cisco.com/cableplan/Schema2}LINK_INFO', attribute 'destPort': 'Eth11' is not a valid value of the atomic type '{http://www.cisco.com/cableplan/Schema2}portType'. /bootflash/cp_failure.xml:7: element LINK_INFO: Schemas validity error : Element '{http://www.cisco.com/cableplan/Schema2}LINK_INFO', attribute 'destPort': [facet 'pattern'] The value 'Et1/1' is not accepted by the pattern 'Eth[0-9]{1,3}/[0-9]{1,3}'. /bootflash/cp_failure.xml:7: element LINK_INFO: Schemas validity error : Element '{http://www.cisco.com/cableplan/Schema2}LINK_INFO', attribute 'destPort': 'Et1/1' is not a valid value of the atomic type '{http://www.cisco.com/cableplan/Schema2}portType'. /bootflash/cp_failure.xml:11: element LINK_INFO: Schemas validity error : Element '{http://www.cisco.com/cableplan/Schema2}LINK_INFO', attribute 'destPort': [facet 'pattern'] The value 'Eth18881/2' is not accepted by the pattern 'Eth[0-9]{1,3}/[0-9]{1,3}'. /bootflash/cp_failure.xml:11: element LINK_INFO: Schemas validity error : Element '{http://www.cisco.com/cableplan/Schema2}LINK_INFO', attribute 'destPort': 'Eth18881/2' is not a valid value of the atomic type '{http://www.cisco.com/cableplan/Schema2}portType'. /bootflash/cp_failure.xml:13: element LINK_INFO: Schemas validity error : Element '{http://www.cisco.com/cableplan/Schema2}LINK_INFO', attribute 'destPort': [facet 'pattern'] The value 'th1/2' is not accepted by the pattern 'Eth[0-9]{1,3}/[0-9]{1,3}'. /bootflash/cp_failure.xml:13: element LINK_INFO: Schemas validity error : Element '{http://www.cisco.com/cableplan/Schema2}LINK_INFO', attribute 'destPort': 'th1/2' is not a valid value of the atomic type '{http://www.cisco.com/cableplan/Schema2}portType'. Error: Failed to import cable-plan: Invalid cable-plan Device#The following is a sample cable plan for a data center with two spine devices and three leaf devices. This cable plan describes a data center that contains the following switches: spine1, spine2, leaf1, leaf2, and leaf3. The sourceChassis, spine2 is connected to destChassis, leaf1 through Ethernet 1/1. If your data center network has more interfaces than the ones described in the cable plan, a warning about the absence is logged.
<?xml version="1.0" encoding="UTF-8"?> <CISCO_NETWORK_TYPES version="1.0" xmlns="http://www.cisco.com/cableplan/Schema2" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.cisco.com/cableplan/Schema2 nxos-cable-plan-schema.xsd "> <DATA_CENTER networkLocation="san-jose" idFormat="hostname"> <CHASSIS_INFO sourceChassis="spine1" type="n7k"> <LINK_INFO sourcePort="Eth2/1" destChassis="leaf1" destPort="Eth2/1"/> <LINK_INFO sourcePort="Eth2/2" destChassis="leaf2" destPort="Eth2/1"/> <LINK_INFO sourcePort="Eth2/3" destChassis="leaf3" destPort="Eth2/1"/> </CHASSIS_INFO> <CHASSIS_INFO sourceChassis="spine2.cisco.com" type="n7k"> <LINK_INFO sourcePort="Eth1/1" destChassis="leaf1" destPort="Eth1/2"/> <LINK_INFO sourcePort="Eth1/2" destChassis="leaf2" destPort="Eth1/2"/> <LINK_INFO sourcePort="Eth1/3" destChassis="leaf3" destPort="Eth1/2"/> </CHASSIS_INFO> </DATA_CENTER> </CISCO_NETWORK_TYPES>The following paragraphs describe the lines and the XML tags and attributes associated with each line in the cable plan. These lines are required headings for XML processing and Cisco-specific headers that denote that this is a Cisco cable plan. The format must be exactly the same as shown in the following example for all cable plans. Failure to adhere to the format results in a rejected cable plan.
The CISCO_NETWORK_TYPES tag is required and it is the parent tag for the entire XML cable plan. The entire cable plan must be within this tag.<?xml version="1.0" encoding="UTF-8"?> <CISCO_NETWORK_TYPES version="1.0" xmlns="http://www.cisco.com/cableplan/Schema2" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.cisco.com/cableplan/Schema2 nxos-cable-plan-schema.xsd ">The DATA_CENTER tag is required and it houses all information about each chassis in the plan. The networkLocation tag is required and it specifies the location of the data center. The idFormat tag is required and it specifies the format in which IDs are present in subsequent entries. In the Cisco NX-OS Release 6.0(2)N3(1), the only supported format is "hostname". Cable plans that do not use "hostname" as the format are rejected.
<DATA_CENTER networkLocation="san-jose" idFormat="hostname">The CHASSIS_INFO tag is required and it describes one single chassis. All interfaces that belong to the sourceChassis that administrators want to include in the cable plan must be within this tag. The sourceChassis tag is required and it describes the chassis that all subsequent interfaces (described below by LINK_INFO tags) belong to.
Include all details about the interfaces on a device inside the CHASSIS_INFO tag. If you need to check interfaces on another device, include them inside another CHASSIS_INFO tag. There is no limit to the number of unique CHASSIS_INFO tags in a cable plan.
In the following example, all interfaces within the CHASSIS_INFO tag belong to spine1 chassis. The specified chassis name must be the fully qualified domain name of the device. If a domain name is configured for the hostname, the hostname must be followed by the domain name. For example, spine1.cisco.com if spine1 is configured with the domain name, cisco.com.
The type tag is required and it specifies the type of chassis. In the Cisco NX-OS Release 6.0(2)N3(1), only Cisco Nexus switches are supported. This tag is not case sensitive. Cable plans that do not adhere to the "n#k" format are rejected.
<CHASSIS_INFO sourceChassis="spine1" type="n7k">The LINK_INFO tag is required and it describes an interface connection from the sourceChassis to the destChassis. In the following example, the spine1 source port on Ethernet 2/1 is connected to the leaf1 destination port on Ethernet2/1, spine1 source port on Ethernet 2/2 is connected to leaf2 destination port on Ethernet 2/1, and so on.
The sourcePort tag is required and it denotes the port on the sourceChassis. Source ports must be unique per chassis. For example, spine1 must not specify multiple connections that come from port Ethernet 2/1. The cable plan import will not fail if you do not specify unique ports. However, a warning is displayed on the console and only the first entry is read and checked by the cable plan.
The destChassis tag is required and it denotes the destination chassis that the sourceChassis is connected to. The destChassis name must be the fully qualified domain name.
The destPort tag is required and it denotes the port on the destination chassis. Like the sourcePort, the destPort must be unique to the destChassis.
<LINK_INFO sourcePort="Eth2/1" destChassis="leaf1" destPort="Eth2/1"/> <LINK_INFO sourcePort="Eth2/2" destChassis="leaf2" destPort="Eth2/1"/> <LINK_INFO sourcePort="Eth2/3" destChassis="leaf3" destPort="Eth2/1"/>
Related Commands
Command
Description
Related Information
Clears the current cable plan.
Enables the cable management feature for a network
Displays the cable plan available in the system memory.
fabric connectivity mismatch action delay
To delay the port error-disable action on detecting cabling errors for a specified time, use the fabric connectivity mismatch action delay command in global configuration mode. To remove this configuration, use the no form of this command
Syntax Description
Command History
Usage Guidelines
Use this command to delay, by seconds, any action caused by mismatched errors. For example, if you set the action delay to 30 seconds and have errors configured to error-disable ports, then in case an error is detected at a network port, the port is error-disabled after a period of 30 seconds. If a valid entry is received within the wait period of 30 seconds, the port will remain open and not be error-disabled. You have to enable the cable management feature using the feature cable-management command to be able to configure the fabric connectivity mismatch action delay command.
Related Commands
Command
Description
Related Information
Displays cache information about fabric connectivity neighbors.
Imports a cable plan from a local or a remote location.
Configures the tier level of a device.
fabric connectivity tier
To configure the tier level of a device in the Dynamic Fabric Automation (DFA) fabric, use the fabric connectivity tier command in global configuration mode. To remove this configuration, use the no form of this command.
Syntax Description
tier-level Tier level of the device. The range is from 1 to 16, where 1 indicates a leaf, 2 indicates a level 1 spine, 3 indicates a level 2 spine, and so on.
Command History
Usage Guidelines
To detect and resolve miscabling issues in a Clos network, DFA provides the user the functionality to assign a sequential number (called the tier number) at each stage of the network topology. Every device in a stage can be associated with the corresponding tier level number assigned to the stage the device is in. All leaf switches (in the lowest level of the Clos stage) are provisioned with a tier level of 1, the next higher-level stage devices (1st stage of spine switches) are provisioned with a tier level value of 2, and the next higher-level stage devices (2nd stage of spine switches) are provisioned with a tier level of 3, and so on. Use the fabric connectivity tier command to assign the tier-level number for a specific device in the fabric. You have to enable the cable management feature using the feature cable-management command to be able to configure the fabric connectivity tier command.
Related Commands
Command
Description
Related Information
Clears all information about neighbors from the neighbor cache.
Imports a cable plan from a local or a remote location.
Delays the port error-disable action on detecting cabling errors for a specified time.
fabric database mobility-domain
To configure the mobility domain name, use the fabric database mobility-domain command in global configuration mode. To remove the mobility domain name, use the no form of this command.
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Enables configuring host mobility-specific commands.
fabric database type
To configure the external database, use the fabric database type command in global configuration mode. To remove this configuration, use the no form of this command
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Clears the external database statistics such as number of messages sent or received, pending requests, access errors, and access timeouts
Displays fabric database statistics.
fabric forwarding anycast-gateway-mac
To specify the MAC address of the server facing ports across all leaf nodes, use the fabric forwarding anycast-gateway-mac command in global configuration mode. To disable the anycast gateway MAC address, use the no form of this command.
fabric forwarding anycast-gateway-mac mac-address
no fabric forwarding anycast-gateway-mac mac-address
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Enables configuring host mobility-specific commands.
fabric forwarding control-segment
To configure a control segment under a switched virtual interface (SVI) in a default virtual routing and forwarding (VRF) instance, use the fabric forwarding control-segment command in interface configuration mode.Command History
Usage Guidelines
Use the fabric forwarding control-segment command to specify an SVI interface to be a fabric control VLAN interface on which adjacencies are established in the default VRF. You can configure only one SVI interface in the default VRF as a fabric control VLAN interface.
Note
You can also configure a control segment under a bridge domain.
Related Commands
Command
Description
Related Information
Enables configuring host mobility-specific commands.
fabric forwarding conversational-aging
To configure the conversational aging timeout value, use the fabric forwarding conversational-aging command in global configuration mode. To remove the aging timeout value, use the no form of this command.
Syntax Description
timeout Conversational aging timeout value in minutes. The range is from 15 to 1800. The default is 30.
Command History
Related Commands
Command
Description
Related Information
Enables configuring host mobility-specific commands.
fabric forwarding conversational-learning
To enable Layer 3 conversational learning-based route download into the forwarding information base (FIB), use the fabric forwarding conversational-learning command in global configuration mode. To disable the conversational learning-based FIB route download, use the no form of this command.
Syntax Description
all (Optional) Enables conversational learning for all virtual routing and forwarding (VRF) instances.
Command History
Usage Guidelines
Use the fabric forwarding conversational-learning command to enable Layer 3 conversational learning. After conversational learning is enabled, the host routes are downloaded into the FIB when a conversation is detected.
NoteIf you use this command without the all keyword, it specifies that conversational learning is used for the default VRF.
Related Commands
Command
Description
Related Information
Enables configuring host mobility-specific commands.
fabric forwarding identifier
fabric forwarding switch-role
To specify the role of a device in the network, use the fabric forwarding switch-role command in global configuration mode. To disable the role specified for a device, use the no form of the command.
fabric forwarding switch-role { border [ leaf | spine] | leaf [ border] | spine [ border]}
no fabric forwarding switch-role
Syntax Description
border Sets border as the role of a device.
leaf Sets leaf as the role of a device.
spine Sets spine as the role of a device.
Command History
Usage Guidelines
Use the fabric forwarding switch-role command to specify the role of a device. You can configure a device to act like a border, a spine or a leaf. A device sends notifications to registered components whenever there is a change in the role of a device. You can specify a combination of a border and a leaf or a spine on a device. Both Border Gateway Protocol (BGP) and Intermediate System-to-Intermediate System (ISIS) protocol restart when the role of a device changes.
Examples
The following example shows how to specify the role of a device to be a border and a spine:
Device> enable Device# configure terminal Device(config)# install feature-set fabric Device(config)# feature-set fabric Device(config)# fabric forwarding switch-role border spineThe following example shows how to specify the role of a device to be a border and a leaf.
Device> enable Device# configure terminal Device(config)# install feature-set fabric Device(config)# feature-set fabric Device(config)# fabric forwarding switch-role border leaf
Related Commands
Command
Description
Related Information
Enables configuring host mobility-specific commands.
fabricpath isis bfd
To enable the FabricPath Bidirectional Forwarding (BFD) feature on an Intermediate System-to-Intermediate System (IS-IS) interface, use the fabricpath isis bfd command in interface configuration mode. To disable the FabricPath BFD feature on the IS-IS interface, use the no form of this command.
Syntax Description
Command History
Usage Guidelines
The no fabricpath isis bfd command disables the BFD on the interface, but if global BFD is configured, the interface inherits the global BFD and BFD is remains enabled on that interface.
The no fabricpath isis bfd disable command disables the BFD on the interface even if global BFD is configured. This command overrides the global BFD configuration. No BFD is configured on that interface .
Related Commands
Command
Description
Related Information
Displays information about FabricPath IS-IS.
Displays information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) interface.
fabricpath oam profile
To configure a FabricPath Operation, Administration, and Maintenance (OAM) profile and enter FabricPath OAM profile configuration mode, use the fabricpath oam profile command in global configuration mode. To remove the FabricPath OAM profile, use the no form of this command.
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Shows statistics for FabricPath OAM loopback.
Shows statistics for fabricpath OAM mtrace.
Shows information about for FabricPath OAM notification.
Shows statistics for FabricPath OAM traceroute.
feature cable-management
To enable the cable management feature for a network, use the feature cable-management command in global configuration mode. To disable the feature, use the no form of this command.
Command History
feature evb
To enable the Edge Virtual Bridging (EVB) feature on a device, use the feature evb command in global configuration mode. To disable EVB feature, use the no form of this command.
Command History
Related Commands
Command
Description
Related Information
Configures the keepalive parameter for EVB.
Configures the resource wait delay parameter for EVB.
Displays information associated with Edge Virtual Bridging (EVB).
feature fabric
To enable fabric network services on a device, use the feature fabric command in global configuration mode. To disable the fabric network services, use the no form of this command.
feature fabric { access | forwarding | multicast }
no feature fabric { access | forwarding | multicast }
Syntax Description
access Enables single point of access in an Extensible Messaging and Presence Protocol (XMPP) client for a fabric network.
forwarding Enables the Host Mobility Manager (HMM) and release-specific HMM configuration commands.
multicast Enables the Next-Gen Multicast VPN (NGMVPN) features associated with the fabric network services.
Command History
feature fabric access
To enable the fabric access feature for a fabric network, use the feature fabric access command in global configuration mode. To disable the fabric access feature, use the no form of this command.
Command History
Related Commands
Command
Description
Related Information
Displays the connection status of a device or a user that is connected in the fabric access network.
feature fabric multicast
To enable the Next-Generation Multicast VPN (NG-MVPN) features on a device, use the feature fabric multicast command in global configuration mode. To disable the NG-MVPN features on a device, use the no form of this command.
Command History
Related Commands
Command
Description
Related Information
Enables configuring host mobility-specific commands.
feature-set fabric
To enable configuring host mobility-specific commands, use the install feature-set fabric command in global configuration mode.
Command History
Related Commands
Command
Description
Related Information
Enables configuring host mobility-specific commands.
feature vn-segment-vlan-based
To enable the (VLAN)-based virtual network (VN) segment feature on a device, use the feature vn-segment-vlan-based command in global configuration mode. To disable VLAN-based VN segment feature, use the no form of this command.
Command History
Related Commands
Command
Description
Related Information
Configures the segment identifier of the VLAN.
Configures the virtual network identifier.
flow (fabricpath-oam)
To configure the direction of FabricPath Operation, Administration, and Maintenance (OAM) packet flow and enter FabricPath OAM profile flow configuration mode, use the flow command in FabricPath OAM profile configuration mode. To remove the flow configuration, use the no form of this command.
Syntax Description
forward Configures the FabricPath OAM forward flow.
reverse Configures the FabricPath OAM reverse flow.
Command History
Related Commands
Command
Description
Related Information
Configures a FabricPath OAM profile.
Configures the FabricPath OAM flow protocol number.
hop (fabricpath-oam)
To configure the hop limit for a FabricPath OAM service packet protocol header, use the hop command in FabricPath OAM profile configuration mode. To restore the hop limit to the default value, use the no form of this command.
Syntax Description
Command History
Related Commands
Command
Description
Related Information
Configures a FabricPath OAM profile.
Configures the FabricPath OAM flow protocol number.
include profile
To configure a set of VLAN profile instances to refer to a common virtual routing and forwarding (VRF) instance, use the include profile command in profile configuration mode. To remove the reference to a common VRF instance, use the no form of this command.
Syntax Description
Command History
Usage Guidelines
Use the include profile command to configure a set of VRF profile instances to refer to a common VRF instance. For example, a set of VLANs can refer to the same VLAN VRF instance. Any configuration after you configure the first VLAN VRF instance will increment the reference count of the include instance. The configuration related to the VRF stays until the last instance referring to the VRF is present.
Related Commands
Command
Description
Related Information
Configures a profile.
install feature-set fabric
To enable configuring host mobility-specific commands, use the install feature-set fabric command in global configuration mode.
Command History
Related Commands
Command
Description
Related Information
Enables configuring host mobility-specific commands.
instance
To create an instance of a user-defined parameter list, use the instance command in parameter list configuration mode. To remove an instance of a user-defined parameter list, use the no form of this command.
Syntax Description
Command History
Usage Guidelines
You can create instances of a parameter list for different hosts with various values. When you create an instance of a parameter list using the instance command, the device enters parameter instance configuration (config-param-inst) mode. The following options are available in this mode:
- set - Sets the parameter value.
- this - Displays information about the instance.
- verify - Verifies the instance with the specified device-profile.
- end - Exits parameter instance configuration mode and returns to EXEC mode.
- exit - Exits parameter instance configuration mode and returns to parameter list configuration mode.
- pop - Pops the mode from the stack or restores it from the specified name.
- push - Pushes the current mode to the stack or saves it with the specified name.
- where - Displays instance-related details (such as parameter-list name, instance name, and so on).
Related Commands
Command
Description
Related Information
Creates user-defined parameters for the specified parameter list.
interface (fabricpath-oam)
To configure a FabricPath Operation, Administration, and Maintenance (OAM) egress interface, use the interface command in FabricPath OAM profile configuration mode. To remove the egress interface configuration, use the no form of this command.
Syntax Description
ethernet Specifies that the egress interface is an Ethernet interface.
slot-number/port-number Interface ID or interface range.
Command History
Related Commands
Command
Description
Related Information
Configures a FabricPath OAM profile.
ip (fabricpath-oam)
To configure a Layer 3 flow destination or source IPv4 address, use the ip command in FabricPath OAM profile flow configuration mode. To remove the IPv4 flow address, use the no form of this command.
Syntax Description
destination Specifies the FabricPath OAM profile flow destination address.
source Specifies the FabricPath OAM profile flow source address.
ip-address IP address.
Command History
Related Commands
Command
Description
Related Information
Configures a FabricPath OAM profile.
Configures the direction FabricPath OAM flow entropy.
ip arp rarp fabric-forwarding
To enable forwarding of Reverse Address Resolution Protocol (RARP) messages from a host to the fabric, and to set a rate-limit for the messages being forwarded, use the ip arp rarp fabric-forwarding command in global configuration mode. To disable forwarding of RARP messages from a host to the fabric, use the no form of this command.
ip arp rarp fabric-forwarding [ rate-limit rate-limit]
no ip arp rarp fabric-forwarding [ rate-limit rate-limit]
Syntax Description
rate-limit rate-limit (Optional) Specifies the forwarding rate of the RARP frames.
Note The default forwarding rate is 200 RARP frames per second. You can specify a forwarding rate in the range of 200 to 400 RARP frames per second. Command History
Usage Guidelines
If you want to enable forwarding of RARP messages and set the rate to the default value of 200 RARP frames per second, then use the ip arp rarp fabric-forwarding command.
If you want to enable forwarding of RARP messages and set the rate to a specific value, then include the use the rate-limit keyword and the rate-limit value.
ip multicast fabric-forwarding
To enable multicast enhanced fabric forwarding for a particular Virtual Routing and Forwarding (VRF), use the ip multicast fabric-forwarding command in global configuration mode. To disable fabric forwarding for the VRF, use the no form of this command.
Related Commands
Command
Description
Related Information
Displays the global state associated with the fabric multicast process.
ipv6 (fabricpath-oam)
To configure a Layer 3 flow destination or source IPv6 address, use the ipv6 command in FabricPath OAM profile flow configuration mode. To remove the IPv6 flow address, use the no form of this command.
Syntax Description
destination Specifies the FabricPath OAM profile flow destination address.
source Specifies the FabricPath OAM profile flow source address.
ip-address IP address.
Command History
Related Commands
Command
Description
Related Information
Configures a FabricPath OAM profile.
Configures the direction FabricPath OAM flow entropy.
logging level evb
To enable the system log (syslog) filter level for an Edge Virtual Bridging (EVB) session, use the logging level evb command in global configuration mode. To disable the syslog filter level for EVB, use the no form of this command.
Syntax Description
Command History
Usage Guidelines
Use the feature evb command to enable the EVB session. This, in turn, enables the evb keyword in the logging level command on the device.
Examples
The following example shows how to set a syslog filter level of 4 for an EVB session:
Device# configure terminal Device(config)# feature evb Device(config)# logging level evb 4 Device(config)# endThe following example displays the default severity level and the user-defined syslog filter level for an EVB session:
Device# show logging level evb Facility Default Severity Current Session Severity -------- ---------------- ------------------------ evb 5 4 0(emergencies) 1(alerts) 2(critical) 3(errors) 4(warnings) 5(notifications) 6(information) 7(debugging)mac-address (fabricpath-oam)
To specify a FabricPath OAM flow destination or source MAC address, use the mac-address command in FabricPath OAM profile flow configuration mode. To remove the MAC address, use the no form of this command.
Syntax Description
destination Specifies the FabricPath OAM profile flow destination MAC address.
source Specifies the FabricPath OAM profile flow source MAC address.
mac-address MAC address.
Command History
Related Commands
Command
Description
Related Information
Configures a FabricPath OAM profile.
Configures the direction FabricPath OAM flow entropy.
match (VLAN access-map)
To specify an access control list (ACL) for traffic filtering in a VLAN access map, use the match command in VLAN access-map configuration mode. To remove a match command from a VLAN access map, use the no form of this command.
Syntax Description
ip Specifies that the ACL is an IPv4 ACL.
ipv6 Specifies that the ACL is an IPv6 ACL.
mac Specifies that the ACL is a MAC ACL.
access-list-name Specifies the ACL by name, which can be up to 64 alphanumeric, case-sensitive characters.
Command History
Release Modification —
This command was introduced in a release earlier than Cisco NX-OS Release 7.0(0)N1(1).
Usage Guidelines
You can specify one or more match commands per entry in a VLAN access map.
By default, the device classifies traffic and applies IPv4 ACLs to IPv4 traffic, IPv6 ACLs to IPv6 traffic, and MAC ACLs to all other traffic.
This command does not require a license.
Examples
This example shows how to create a VLAN access map named vlan-map-01 and add two entries that each have two match commands and one action command:
Device(config-access-map)# vlan access-map vlan-map-01 Device(config-access-map)# match ip address ip-acl-01 switch(config-access-map)# action forward switch(config-access-map)# match mac address mac-acl-00f switch(config-access-map)# vlan access-map vlan-map-01 switch(config-access-map)# match ip address ip-acl-320 switch(config-access-map)# match mac address mac-acl-00e switch(config-access-map)# action drop switch(config-access-map)# show vlan access-map Vlan access-map vlan-map-01 10 match ip: ip-acl-01 match mac: mac-acl-00f action: forward Vlan access-map vlan-map-01 20 match ip: ip-acl-320 match mac: mac-acl-00e action: dropmtrace fabricpath
To trace the path from a source to a destination branch for FabricPath OAM, use the mtrace fabricpath command in privileged EXEC mode.
mtrace fabricpath [ tree id | ftag ftag-id ] { profile profile-id | mac dst dst-mac etype etype | ip dst dst-ip src src-ip | forward flow flow-ent { l2 | l3 } } [ ingress if-id ] { vlan vlan-id | tag tag-id | dot1q dot1q-id intf-id } [use-host-vlan] [ topology t-id ] [ reply mode out-of-band { ipv4 ip-addr | ipv6 ipv6-addr } ] [ data pattern data ] [ size size ] [ validate ] [ repeat repeat-count ] [ switch-id sw-id ] [verbose]
Syntax Description
tree id (Optional) Specifies the ID of the multicast tree to be verified.
ftag ftag-id (Optional) Specifies the multicast Forwarding Tag (FTag) ID.
profile profile-id Specifies the profile ID.
mac dst dst-mac Specifies the destination MAC address.
etype etype Specifies the ether type.
ip dst dst-ip Specifies the destination IP address.
src src-ip Specifies the source IP address.
forward flow flow-ent Specifies the input flow entropy (128 bytes) from actual user data traffic so that FabricPath OAM packet takes the same path as user traffic.
l2 Specifies that the input flow entropy must be terminated until only Layer 2 entries are used. For example, MAC address, VLAN, and e-type. We recommend that you use only one string option.
l3
Note Only IPv4 and IPv6 entries can be processed ingress if-id (Optional) Specifies the ingress interface ID.
vlan vlan-id Specifies the VLAN ID for the multicast tree to be verified.
tag tag-id
Note The VLAN ID and tag ID are mutually exclusive. dot1q dot1q-id intf-id
Note The dot1q option is not available on Cisco Nexus 5000 series and 6000 series switches; it is available only on the Cisco Nexus 7000 series switches. use-host-vlan (Optional) Specifies that only VLAN input should be used. Use this keyword when enhanced forwarding is applied and you do not want to use translated VLAN. Use this option when you specify the ingress interface ID or when you specify the flow entropy through the profile keyword or through forward flow with IP address of customer traffic.
topology t-id (Optional) Specifies the topology ID. Range is from 0 to 63. Default is 0.
reply mode out-of-band (Optional) Specifies that the FabricPath OAM reply mode is out of band. By default, FabricPath OAM is replied in band (on the FabricPath network). Use the reply mode out-of-band keyword to change the mode of reply to out of band for input IPv4 or IPv6 addresses. For routing, only the default VRF is used.
ipv4 ip-addr (Optional) Specifies the input IPv4 address for out-of-band reply.
ipv6 ipv6-addr (Optional) Specifies the input IPv6 address for out-of-band reply.
data pattern data (Optional) Specifies the data pattern.
size size (Optional) Specifies the padding size of data TLV or test TLV. The total size must not be greater than the MTU of the egress interface.
validate (Optional) Validates the ping command.
repeat repeat-count (Optional) Specifies the repeat value.
interval interval-value (Optional) Specifies the minimum send delay between requests, in milliseconds. The range is from 100 to 3600000. Default is 0 for synchronous ping, 1000 for asynchronous ping.
timeout timeout-value (Optional) Specifies the timeout values in seconds. Range is from 1 to 36000.
hop hop-count (Optional) Specifies the FabricPath OAM ping hop count. Range is from 1 to 64. Default is 63.
switch-id sw-id (Optional) Sends an mtrace request to the specified switch ID.
verbose (Optional) Displays additional information.
Command History
Usage Guidelines
For a synchronous ping, traceroute, or mtrace, if the profile has multiple interfaces, only the first interface is selected. Use the interface keyword to overwrite the selected interface. Only one session is created.
The following rules are apply:
- If a tree ID is specified, an ether type cannot be specified.
- If a Layer 2 tree is specified, a source MAC cannot be specified.
- If a Layer 3 tree is specified, a source and destination MAC addresses cannot be specified.
- If flow entropy is specified, type of flow, either Layer 2 or Layer 3, must be specified. If the flow is Layer 2, the source MAC address is overwritten. If the flow is Layer 3, the source and destination MAC addresses are overwritten.
Examples
The following example shows how to specify a FabricPath mtrace for all trees.
Device# mtrace fabricpath vlan 10 Codes: '!' - success, 'Q' - request not sent, '.' - timeout, 'D' - Destination Unreachable, 'X' - unknown return code, 'V' - VLAN nonexistent, 'v' - VLAN in suspended state, 'm' - malformed request, 'C' - Cross Connect Error, 'U' - Unknown RBridge nickname, 'n' - Not AF, '*' - Success, Optional Tlv incomplete, 'I' - Interface not in forwarding state, 'S' - Service Tag nonexistent, 's' - Service Tag in suspended state, 'c' - Corrupted Data/Test Sender handle: 3 FabricPath mtrace for multicast ftag 1, vlan 10 Code SwitchId Interface State TotalTime ================================================== ! 320 Rcvd on Eth1/48 fwd 2ms ! 3498 Rcvd on Eth1/47 fwd 2ms FabricPath mtrace for multicast ftag 2, vlan 10 Code SwitchId Interface State TotalTime ================================================== ! 320 Rcvd on Eth1/48 fwd 2ms ! 3498 Rcvd on Eth1/47 fwd 2ms FabricPath mtrace for multicast ftag 1, vlan 10 Code SwitchId Interface State TotalTime ================================================== ! 320 Rcvd on Eth1/48 fwd 2ms ! 3498 Rcvd on Eth1/47 fwd 2ms FabricPath mtrace for multicast ftag 2, vlan 10 Code SwitchId Interface State TotalTime ================================================== ! 320 Rcvd on Eth1/48 fwd 2ms ! 3498 Rcvd on Eth1/47 fwd 3ms FabricPath mtrace for multicast ftag 1, vlan 10 Code SwitchId Interface State TotalTime ================================================== ! 320 Rcvd on Eth1/48 fwd 2ms ! 3498 Rcvd on Eth1/47 fwd 3msThe following example shows how to specify FabricPath mtrace for a specific tree.
Device(#) mtrace fabricpath tree 1 vlan 10 repeat 1 Codes: '!' - success, 'Q' - request not sent, '.' - timeout, 'D' - Destination Unreachable, 'X' - unknown return code, 'V' - VLAN nonexistent, 'v' - VLAN in suspended state, 'm' - malformed request, 'C' - Cross Connect Error, 'U' - Unknown RBridge nickname, 'n' - Not AF, '*' - Success, Optional Tlv incomplete, 'I' - Interface not in forwarding state, 'S' - Service Tag nonexistent, 's' - Service Tag in suspended state, 'c' - Corrupted Data/Test Sender handle: 4 FabricPath mtrace for multicast ftag 1, vlan 10 Code SwitchId Interface State TotalTime ================================================== ! 3498 Rcvd on Eth1/47 fwd 2ms ! 320 Rcvd on Eth1/48 fwd 3msThe following example shows how to specify FTag instead of tree.
Device(#) mtrace fabricpath ftag 1 vlan 10 repeat 1 verbose Codes: '!' - success, 'Q' - request not sent, '.' - timeout, 'D' - Destination Unreachable, 'X' - unknown return code, 'V' - VLAN nonexistent, 'v' - VLAN in suspended state, 'm' - malformed request, 'C' - Cross Connect Error, 'U' - Unknown RBridge nickname, 'n' - Not AF, '*' - Success, Optional Tlv incomplete, 'I' - Interface not in forwarding state, 'S' - Service Tag nonexistent, 's' - Service Tag in suspended state, 'c' - Corrupted Data/Test Sender handle: 6 FabricPath mtrace for multicast ftag 1, vlan 10 Code SwitchId Interface State TotalTime DownSwitchId Intf State ============================================================================ ! 3498 Rcvd on Eth1/47 fwd 2ms ! 320 Rcvd on Eth1/48 fwd 3msThe following example shows how to specify a pair of trees.
Device(#) mtrace fabricpath ip dst 224.1.1.1 src 10.1.1.1 vlan 10 repeat 1 Codes: '!' - success, 'Q' - request not sent, '.' - timeout, 'D' - Destination Unreachable, 'X' - unknown return code, 'V' - VLAN nonexistent, 'v' - VLAN in suspended state, 'm' - malformed request, 'C' - Cross Connect Error, 'U' - Unknown RBridge nickname, 'n' - Not AF, '*' - Success, Optional Tlv incomplete, 'I' - Interface not in forwarding state, 'S' - Service Tag nonexistent, 's' - Service Tag in suspended state, 'c' - Corrupted Data/Test Sender handle: 7 FabricPath mtrace for multicast ftag 1, vlan 10 Code SwitchId Interface State TotalTime ================================================== ! 320 Rcvd on Eth1/48 fwd 2ms
Related Commands
Command
Description
Related Information
Tests the FabricPath OAM reachability.
Discovers the FabricPath route.
