Guest

IP Application Services

The Traps Sent with SNMP-Server Enabled Traps Configured

Hierarchical Navigation

Document ID: 45362

Updated: Oct 26, 2005

   Download PDF
   Print

Introduction

This document describes the traps sent when you configure the command snmp-server enable traps <…> on a Cisco device.

Prerequisites

Requirements

Readers of this document should have knowledge of these topics:

  • How to configure SNMP on a Cisco device

  • Use of SNMP get and walk commands

Components Used

This document applies to Cisco devices (routers and switches) that run IOS which supports SNMP. The information in this document is based on several releases of IOS® because the trap command differs from release to release and platform to platform. For example, you will not have the capacity to send ATM related traps on a system that has no ATM interface.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Refer to Cisco Technical Tips Conventions for more information on document conventions.

An Overview of the Traps Enabled on Your Device

In order to get an overview of the traps you have enabled on your device, issue this command on every Cisco IOS device: 

cognac# conf t

Enter configuration commands, one per line.  End with CNTL/Z.

cognac(config)# snmp-server enable traps ?

  atm          Enable SNMP atm traps

  bgp          Enable BGP state change traps

  config       Enable SNMP config traps

  dial         Enable SNMP dial control traps

  dlsw         Enable SNMP dlsw traps

  dsp          Enable SNMP dsp traps

  entity       Enable SNMP entity traps

  envmon       Enable SNMP environmental monitor traps

  frame-relay  Enable SNMP frame-relay traps

  hsrp         Enable SNMP HSRP traps

  ipmulticast  Enable SNMP ipmulticast traps

  isdn         Enable SNMP isdn traps

  msdp         Enable SNMP MSDP traps

  rsvp         Enable RSVP flow change traps

  rtr          Enable SNMP Response Time Reporter traps

  snmp         Enable SNMP traps

  syslog       Enable SNMP syslog traps

  tty          Enable TCP connection traps

  voice        Enable SNMP voice traps

  xgcp         Enable XGCP protocol traps

  <cr>
 
cognac(config)#

Once you know the traps you have enabled, you can enable them as you need. This document helps you find which traps are sent when you enable a command.

Note:  This list can differ from platform to platform and release to release because of the features in a specific device and available interfaces.

Traps Sent When You Enable Commands from the List

aaa-server Sends AAA server notifications 12.1(3)T AS5300 AS5800 CISCO-AAA-SERVER-MIB 1.3.6.1.4.1.9.10.56.2.0.1 casServerStateChange
bgp Sends Border Gateway Protocol (BGP) state change notifications / / BGP4-MIB 1.3.6.1.2.1.15.7.1 1.3.6.1.2.1.15.7.2 bgpEstablished bgpBackwardTransition
calltracker Sends notification whenever a new active call entry is created in the cctActiveTable or a new history call entry is created in the cctHistoryTable / / CISCO-CALL-TRACKER-MIB 1.3.6.1.4.1.9.9.163.2.0.1 1.3.6.1.4.1.9.9.163.2.0.2 cctCallSetupNotification cctCallTerminateNotification
config Sends configuration notifications / / CISCO-CONFIG-MAN-MIB 1.3.6.1.4.1.9.9.43.2.0.1 ciscoConfigManEvent
dial Sends notification whenever
  • a successful call clears
  • a failed call attempt is determined to have ultimately failed
  • whenever a call setup message is received or sent
 / / DIAL-CONTROL-MIB 1.3.6.1.2.1.10.21.2.0.1 1.3.6.1.2.1.10.21.2.0.2 dialCtlPeerCallInformation dialCtlPeerCallSetup
dlsw Sends notifications from DLSw agents. When the dlsw keyword is used, you can specify a notification-option value. / / CISCO-DLSW-MIB 1.3.6.1.4.1.9.10.9.1.7.1 1.3.6.1.4.1.9.10.9.1.7.2 1.3.6.1.4.1.9.10.9.1.7.3 1.3.6.1.4.1.9.10.9.1.7.4 1.3.6.1.4.1.9.10.9.1.7.5 1.3.6.1.4.1.9.10.9.1.7.6 ciscoDlswTrapTConnPartnerReject ciscoDlswTrapTConnProtViolation ciscoDlswTrapTConnUp ciscoDlswTrapTConnDown ciscoDlswTrapCircuitUp ciscoDlswTrapCircuitDown
ds0-busyout Sends notification whenever the busyout of a DS0 interface changes state 12.1(3)T AS5300 CISCO-POP-MGMT-MIB 1.3.6.1.4.1.9.10.19.2.0.1 cpmDS0BusyoutNotification
ds1-loopback Sends notification whenever the DS1 interface goes into loopback mode 12.1(3)T AS5300 CISCO-POP-MGMT-MIB 1.3.6.1.4.1.9.10.19.2.0.2 cpmDS1LoopbackNotification
dspu Sends notification whenever the operational state of the physical unit (PU) or the logical unit (LU) changes or activation failure is detected / / CISCO-DSPU-MIB 1.3.6.1.4.1.9.9.24.1.4.4.0.1 1.3.6.1.4.1.9.9.24.1.4.4.0.2 1.3.6.1.4.1.9.9.24.1.5.3.0.1 1.3.6.1.4.1.9.9.24.1.5.3.0.2 newdspuPuStateChangeTrap newdspuPuActivationFailureTrap newdspuLuStateChangeTrap dspuLuActivationFailureTrap
dsp Sends notification whenever the DSP card is going up or down / / CISCO-DSP-MGMT-MIB 1.3.6.1.4.1.9.9.86.2.0.1 cdspMIBCardStateNotification
entity Sends Entity MIB modification notifications / / ENTITY-MIB 1.3.6.1.2.1.47.2.0.1 entConfigChange
envmon Sends Cisco enterprise-specific environmental monitor notifications when an environmental threshold is exceeded. When the envmon keyword is used, you can specify a notification-option value. / / CISCO-ENVMON-MIB 1.3.6.1.4.1.9.9.13.3.0.1 1.3.6.1.4.1.9.9.13.3.0.2 1.3.6.1.4.1.9.9.13.3.0.3 1.3.6.1.4.1.9.9.13.3.0.4 1.3.6.1.4.1.9.9.13.3.0.5 ciscoEnvMonShutdownNotification ciscoEnvMonVoltageNotification ciscoEnvMonTemperatureNotification ciscoEnvMonFanNotification ciscoEnvMonRedundantSupplyNotification
frame-relay Sends Frame Relay notifications / / RFC1315-MIB 1.3.6.1.2.1.10.32.0.1 frDLCIStatusChange
hsrp Sends Hot Standby Router Protocol (HSRP) notifications 12.0(3)T / CISCO-HSRP-MIB 1.3.6.1.4.1.9.9.106.2.0.1 cHsrpStateChange
isdn Sends Integrated Services Digital Network (ISDN) notifications. When the isdn keyword is used, you can specify a notification-option value. 12.1(1)T 12.1(5)T / CISCO-ISDN-MIB CISCO-ISDNU-IF-MIB 1.3.6.1.4.1.9.9.26.2.0.1 1.3.6.1.4.1.9.9.26.2.0.2 1.3.6.1.4.1.9.9.26.2.0.3 1.3.6.1.4.1.9.9.26.2.0.4 1.3.6.1.4.1.9.9.18.2.0.1 demandNbrCallInformation demandNbrCallDetails demandNbrLayer2Change demandNbrCNANotification ciuIfLoopStatusNotification
msdp Sends Multicast Source Discovery Protocol (MSDP) notifications / / MSDP-MIB 1.3.6.1.3.92.1.1.7.1 1.3.6.1.3.92.1.1.7.2 msdpEstablished msdpBackwardTransition
repeater Sends Ethernet hub repeater notifications / Cisco-HUB CISCO-REPEATER-MIB 1.3.6.1.4.1.9.9.22.3.0.1 ciscoRptrIllegalSrcAddrTrap
rsvp Sends Resource Reservation Protocol (RSVP) notifications / / RSVP-MIB 1.3.6.1.2.1.51.3.0.1 1.3.6.1.2.1.51.3.0.2 newFlow lostFlow
rtr Sends Service Assurance Agent RTR (RTR) notifications / / CISCO-RTTMON-MIB 1.3.6.1.4.1.9.9.42.2.0.1 1.3.6.1.4.1.9.9.42.2.0.2 1.3.6.1.4.1.9.9.42.2.0.3 rttMonConnectionChangeNotification rttMonTimeoutNotification rttMonThresholdNotification
snmp Sends Simple Network Management Protocol (SNMP) notifications / / CISCO-GENERAL-TRAPS 1.3.6.1.6.3.1.1.5.1 1.3.6.1.6.3.1.1.5.3 1.3.6.1.6.3.1.1.5.4 1.3.6.1.6.3.1.1.5.5 coldStart linkDown linkUp authenticationFailure egpNeighborLoss reload
syslog Sends error message notifications (Cisco Syslog MIB). Specify the level of messages to be sent with the logging history level command / / CISCO-SYSLOG-MIB 1.3.6.1.4.1.9.9.41.2.0.1 clogMessageGenerated
voice Sends poor quality of voice notification / / CISCO-VOICE-DIAL-CONTROL-MIB 1.3.6.1.4.1.9.9.63.2.0.1 cvdcPoorQoVNotification
xgcp Sends External Media Gateway Control Protocol (XGCP) notifications / / XGCP-MIB 1.3.6.1.3.90.2.0.1 xgcpUpDownNotification
channel-failures This trap indicates that a significant link event has been recognized resulting in the degradation of the interface line quality / / CISCO-CHANNEL-MIB 1.3.6.1.4.1.9.9.20.1.5.1 1.3.6.1.4.1.9.9.20.1.5.2 cipCardLinkFailure cipCardDtrBrdLinkFailure
llc2 Sends Logical Link Control, type2 notifications / / CISCO-SDLLC-MIB 1.3.6.1.4.1.9.9.28.2.1 convSdllcPeerStateChangeNotification
rsrb Indicates that the state of an RSRB remote peer has transitioned to Active or Inactive. / / CISCO-RSRB-MIB 1.3.6.1.4.1.9.9.29.2.1 rsrbPeerStateChangeNotification
sdlc Indicates that the state of an SDLC port has transitioned. Indicates that the state of an SDLC station has transitioned to Contacted or Discontacted. Indicates that the state of an SDLC link has transitioned to Contacted or Discontacted. / / SNA-SDLC-MIB 1.3.6.1.2.1.41.1.3.1 1.3.6.1.2.1.41.1.3.2 1.3.6.1.2.1.41.1.3.3 sdlcPortStatusChange sdlcLSStatusChange sdlcLSStatusChange1
stun Indicated that the state of a STUN route has transitioned to Active or Inactive / / CISCO-STUN-MIB 1.3.6.1.4.1.9.9.30.2.1 stunPeerStateChangeNotification

Related Information

Updated: Oct 26, 2005
Document ID: 45362