Document ID: 7276
Updated: Jan 14, 2008
Contents
Introduction
This sample configuration shows how to encrypt traffic between two private networks (10.50.50.x and 10.103.1.x) using IPSec. The networks know each other by their private addresses.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on these software and hardware versions:
-
Cisco IOS® Software Release 12.3.1a
-
Cisco 2691 Routers
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
For more information on document conventions, refer to Cisco Technical Tips Conventions.
Configure
In this section, you are presented with the information to configure the features described in this document.
Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only) .
Network Diagram
This document uses the network setup shown in this diagram.
Configurations
This document uses these configurations.
| Router A |
|---|
Router_A#write terminal Building configuration... Current configuration : 1638 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router_A ! boot system flash:c2691-ik9o3s-mz.123-1a.bin ! ip subnet-zero ! ip audit notify log ip audit po max-events 100 no ftp-server write-enable ! crypto isakmp policy 1 hash md5 authentication pre-share crypto isakmp key cisco123 address 95.95.95.2 ! crypto ipsec transform-set rtpset esp-des esp-md5-hmac ! crypto map rtp 1 ipsec-isakmp set peer 95.95.95.2 set transform-set rtpset !--- Include the private network to private network traffic !--- in the encryption process. match address 115 ! no voice hpi capture buffer no voice hpi capture destination ! interface FastEthernet0/0 ip address 99.99.99.2 255.255.255.0 ip nat outside duplex auto speed auto crypto map rtp ! interface FastEthernet0/1 ip address 10.50.50.50 255.255.255.0 ip nat inside duplex auto speed auto ! !--- Except the private network traffic from the !--- Network Address Translation (NAT) process. ip nat inside source route-map nonat interface FastEthernet0/0 overload ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 99.99.99.1 ! !--- Except the private network traffic from the NAT process. access-list 110 deny ip 10.50.50.0 0.0.0.255 10.103.1.0 0.0.0.255 access-list 110 permit ip 10.50.50.0 0.0.0.255 any !--- Include the private network to private network traffic !--- in the encryption process. access-list 115 permit ip 10.50.50.0 0.0.0.255 10.103.1.0 0.0.0.255 ! !--- Except the private network traffic from the NAT process. route-map nonat permit 10 match ip address 110 ! dial-peer cor custom ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! end Router_A# |
| Router B |
|---|
Router_B#write terminal Building configuration... Current configuration : 1394 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router_B ! boot system flash:c2691-ik9o3s-mz.123-1a.bin ! ip subnet-zero ! ip audit notify log ip audit po max-events 100 no ftp-server write-enable ! crypto isakmp policy 1 hash md5 authentication pre-share crypto isakmp key cisco123 address 99.99.99.2 ! crypto ipsec transform-set rtpset esp-des esp-md5-hmac ! crypto map rtp 1 ipsec-isakmp set peer 99.99.99.2 set transform-set rtpset !--- Include the private network to private network traffic !--- in the encryption process. match address 115 ! no voice hpi capture buffer no voice hpi capture destination ! interface FastEthernet0/0 ip address 95.95.95.2 255.255.255.0 ip nat outside duplex auto speed auto crypto map rtp ! interface FastEthernet0/1 ip address 10.103.1.75 255.255.255.0 ip nat inside duplex auto speed auto ! !--- Except the private network traffic from the NAT process. ip nat inside source route-map nonat interface FastEthernet0/0 overload ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 95.95.95.1 ! !--- Except the private network traffic from the NAT process. access-list 110 deny ip 10.103.1.0 0.0.0.255 10.50.50.0 0.0.0.255 access-list 110 permit ip 10.103.1.0 0.0.0.255 any !--- Include the private network to private network traffic !--- in the encryption process. access-list 115 permit ip 10.103.1.0 0.0.0.255 10.50.50.0 0.0.0.255 ! !--- Except the private network traffic from the NAT process. route-map nonat permit 10 match ip address 110 ! dial-peer cor custom ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! end Router_B# |
Verify
There is currently no verification procedure available for this configuration.
Troubleshoot
Troubleshooting Commands
Certain show commands are supported by the Output Interpreter Tool (registered customers only) , which allows you to view an analysis of show command output.
Note: Before issuing debug commands, refer to Important Information on Debug Commands.
-
debug crypto ipsec sa—Displays the IPSec negotiations of phase 2.
-
debug crypto isakmp sa—Displays the Internet Security Association and Key Management Protocol (ISAKMP) negotiations of phase 1.
-
debug crypto engine—Displays the encrypted sessions.
Related Information
Open a Support Case 
(Requires a Cisco Service Contract.)
Related Cisco Support Community Discussions
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.