Document ID: 110353
Updated: May 18, 2009
Contents
Introduction
This sample configuration demonstrates how to configure a Router with Zone Based Firewall and NAT configuration to serve as a termination of Point-to-Point Tunneling Protocol (PPTP) connections.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on these software and hardware versions:
-
Cisco Router 871
-
Cisco IOS® Software Release 12.4T and later
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
Refer to the Cisco Technical Tips Conventions for more information on document conventions.
Background Information
The internal network has a server that users on the Internet can access once they are connected through PPTP that terminates on an Internet facing router. All other access to hosts on the internal network is denied from outside users.
-
IP address of the Internal server—10.22.22.10
-
IP address of the Remote Client PC—10.66.83.50
All users on the internal network are allowed unrestricted access to the Internet. These internal users use PAT on the Router in order to reach the Internet. All traffic from the Internal users is inspected on passing through the Router.
Configure
In this section, you are presented with the information to configure the features described in this document.
Note: Use the Command Lookup Tool (registered customers only) to obtain more information on the commands used in this section.
Network Diagram
This document uses this network setup:
PPTP Router Configuration
This document uses this configuration.
These Cisco IOS commands are applicable to all platforms that support PPTP.
Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. !--- Enable virtual private dial-up networking. Router(config)#vpdn enable !--- Enters VPDN group configuration mode for the specified VPDN group. Router(config)#vpdn-group 1 !--- Enters VPDN accept-dialin configuration mode !--- and enables the router to accept dial-in requests. Router(config-vpdn)#accept-dialin !--- Specifies which PPTP protocol is used. Router(config-vpdn-acc-in)#protocol pptp !--- Specifies the virtual template that is used !--- in order to clone the virtual access interface. Router(config-vpdn-acc-in)#virtual-template 1 Router(config-vpdn-acc-in)#exit Router(config)#ip local pool defaultpool 192.168.100.1 192.168.100.254 !--- Create virtual-template interface used for cloning !--- virtual-access interfaces with the use of address pool defaultpool !--- with Challenge Authentication Protocol (CHAP) authentication and MS-CHAP. Router(config)#interface virtual-template 1 Router(config-if)#encapsulation ppp Router(config-if)#peer default ip address pool defaultpool Router(config-if)#ip unnumbered FastEthernet4 Router(config-if)#ppp authentication chap ms-chap
Note: Non-default commands are shown in bold.
| Router |
|---|
Router#show run Building configuration... Current configuration : 3666 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot system flash flash:c870-advsecurityk9-mz.124-20.T3.bin boot-end-marker ! logging message-counter syslog enable password cisco ! aaa new-model ! ! aaa authentication login VTY local ! !--- Define local authentication for PPP. ! aaa authentication ppp default local ! ! aaa session-id common ! ! dot11 syslog ip source-route ! ! ip cef ip domain name cisco.com ! ! vpdn enable ! !--- Enable VDPN. ! vpdn-group PPTP-VPDN ! !--- Default PPTP VPDN group. ! accept-dialin protocol pptp virtual-template 1 ! ! !--- Defining local username and password. ! username cisco privilege 15 password 0 cisco ! archive log config hidekeys ! ! ip ssh version 1 ! !--- Defining Zone-Based Policy Firewall Class-Maps. ! class-map type inspect match-all PPTP-Pass-Through-Traffic match access-group name PPTP-PASS-THROUGH class-map type inspect match-any All-Traffic match protocol tcp match protocol udp match protocol icmp class-map type inspect match-all Router-Access-Traffic match access-group name Router-Access class-map type inspect match-all PPTP-Terminated-Traffic match access-group name PPTP-TERMINATED ! ! !--- Defining Zone-Based Policy Firewall Policy-Maps. ! policy-map type inspect PPTP-In-Policy class type inspect All-Traffic inspect class class-default drop policy-map type inspect Out-In-Policy class type inspect PPTP-Pass-Through-Traffic pass class class-default drop policy-map type inspect In-Out-Policy class type inspect PPTP-Pass-Through-Traffic pass class type inspect All-Traffic inspect class class-default drop policy-map type inspect Out-Self-Policy class type inspect Router-Access-Traffic pass class type inspect PPTP-Terminated-Traffic pass class class-default drop ! !--- Defining the different zones. ! zone security outside zone security inside zone security pptp ! !--- Defining the zone-pairs for different flows of traffic. ! zone-pair security outside-self source outside destination self service-policy type inspect Out-Self-Policy zone-pair security pptp-in source pptp destination inside service-policy type inspect PPTP-In-Policy zone-pair security inside-outside source inside destination outside service-policy type inspect In-Out-Policy ! ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface FastEthernet4 description "Connected to Outside Network" ip address 10.66.79.73 255.255.255.224 ! !--- Defines the interface as external for NAT. ! ip nat outside ip virtual-reassembly ! !--- Defines the interface as part of the outside zone. ! zone-member security outside speed 100 full-duplex ! !--- Create virtual-template interface used for cloning !--- virtual-access interfaces with the use of address pool defaultpool !--- with CHAP authentication and MS-CHAP. ! interface Virtual-Template1 ip unnumbered FastEthernet4 ! !--- Defines the interface as part of the pptp zone. ! zone-member security pptp peer default ip address pool defaultpool ppp authentication chap ms-chap ! interface Dot11Radio0 no ip address speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Vlan1 description "Connected to Inside Network" ip address 10.22.22.1 255.255.255.0 ! !--- Defines the interface as internal for NAT. ! ip nat inside ip virtual-reassembly ! !--- Defines the interface as part of the inside zone. ! zone-member security inside ! !--- Enable Create IP pool named test and specify IP range. ! ip local pool defaultpool 192.168.100.1 192.168.100.254 ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 10.66.79.65 no ip http server no ip http secure-server ! !--- Indicates that any packets received on the inside interface !--- matched by access list NO-NAT share one public IP address (the !--- address on Fa4). !--- Note that traffic from the internal network to the remote clients !--- is not natted. ! ip nat inside source list NO-NAT interface FastEthernet4 overload ! !--- Traffic from internal network to remote clients is denied from !--- being natted. ! ip access-list extended NO-NAT deny ip 10.22.22.0 0.0.0.255 192.168.100.0 0.0.0.255 permit ip 10.22.22.0 0.0.0.255 any ! !--- Passing PPTP traffic includes allowing GRE – IP protocol 47. ! ip access-list extended PPTP-PASS-THROUGH permit gre any any ! !--- PPTP terminated traffic involves GRE and TCP port 1723 traffic. ! ip access-list extended PPTP-TERMINATED permit gre any any permit tcp any any eq 1723 ! !--- Allowing Telnet, SSH and HTTPS access ! ip access-list extended Router-Access permit tcp any any eq telnet permit tcp any any eq 22 permit tcp any any eq 443 ! control-plane ! ! line con 0 no modem enable line aux 0 line vty 0 4 login authentication VTY transport input telnet ssh ! scheduler max-task-time 5000 end |
PPTP Client Configuration and Settings
Complete these steps:
-
Choose Start > Settings > Network and Dial-up Connections > Make New Connection.
-
After the Network Connection Wizard window appears, choose Network Connection Type > Connect to the network at my workplace and click Next.
-
Choose Virtual Private Network connection.
-
Specify a Connection Name.
-
Specify a Destination Address in the Host or IP address field and click Next.
-
Choose Start > Settings > Network and Dial up connections and select the recently configured connection.
-
After this window appears, choose Properties > Security in order to set the option properly.
-
Choose Advanced (customer settings) > Settings, and choose the appropriate encryption (Data Encryption) level and authentication (allow these protocols) if needed.
-
Choose Networking > Type of VPN > PPTP VPN and click OK.
-
Enter the username and password to be used for the PPTP connection.
-
The Verifying username and password window appears.
-
The Registering your computer on the network window appears.
-
If you verify the Remote PC, you get an IP address from the configured pool.
Verify
Use this section to confirm that your configuration works properly.
The Output Interpreter Tool (registered customers only) (OIT) supports certain show commands. Use the OIT to view an analysis of show command output.
-
Router#show vpdn
%No active L2TP tunnels PPTP Tunnel and Session Information Total tunnels 1 sessions 1 LocID Remote Name State Remote Address Port Sessions VPDN Group 3 estabd 10.66.83.50 1040 1 PPTP-VPDN LocID RemID TunID Intf Username State Last Chg Uniq ID 3 32768 3 Vi2.1 cisco estabd 00:00:57 2
-
Router#show ip interface brief
Interface IP-Address OK? Method Status Protocol FastEthernet0 unassigned YES unset up up FastEthernet1 unassigned YES unset up down FastEthernet2 unassigned YES unset up down FastEthernet3 unassigned YES unset up down FastEthernet4 10.66.79.73 YES manual up up Dot11Radio0 unassigned YES unset down down SSLVPN-VIF0 unassigned NO unset up up Vlan1 10.22.22.1 YES manual up up NVI0 unassigned NO unset up up Virtual-Template1 10.66.79.73 YES TFTP down down Virtual-Access1 unassigned YES unset down down Virtual-Access2 unassigned YES unset up up Virtual-Access2.1 10.66.79.73 YES TFTP up up
-
Router#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 10.66.79.65 to network 0.0.0.0 C 10.22.22.0/24 is directly connected, Vlan1 10.0.0.0/27 is subnetted, 1 subnets C 10.66.79.64 is directly connected, FastEthernet4 192.168.100.0/32 is subnetted, 1 subnets C 192.168.100.1 is directly connected, Virtual-Access2.1 S* 0.0.0.0/0 [1/0] via 10.66.79.65 -
Router#show users
Line User Host(s) Idle Location * 0 con 0 idle 00:00:00 Interface User Mode Idle Peer Address Vi2.1 cisco PPPoVPDN - 192.168.100.1
-
Ping from the connected client to the Internal Server
-
Router#show policy-map type inspect zone-pair sessions
policy exists on zp outside-self Zone-pair: outside-self Service-policy inspect : Out-Self-Policy Class-map: Router-Access-Traffic (match-all) Match: access-group name Router-Access Pass 14 packets, 358 bytes Class-map: PPTP-Terminated-Traffic (match-all) Match: access-group name PPTP-TERMINATED Pass 52 packets, 4466 bytes Class-map: class-default (match-any) Match: any Drop 21 packets, 1680 bytes policy exists on zp pptp-in Zone-pair: pptp-in Service-policy inspect : PPTP-In-Policy Class-map: All-Traffic (match-any) Match: protocol tcp 0 packets, 0 bytes 30 second rate 0 bps Match: protocol udp 0 packets, 0 bytes 30 second rate 0 bps Match: protocol icmp 1 packets, 40 bytes 30 second rate 0 bps Inspect Class-map: class-default (match-any) Match: any Drop 0 packets, 0 bytes policy exists on zp inside-outside Zone-pair: inside-outside Service-policy inspect : In-Out-Policy Class-map: PPTP-Pass-Through-Traffic (match-all) Match: access-group name PPTP-PASS-THROUGH Pass 4 packets, 320 bytes Class-map: All-Traffic (match-any) Match: protocol tcp 31 packets, 868 bytes 30 second rate 0 bps Match: protocol udp 20 packets, 1271 bytes 30 second rate 0 bps Match: protocol icmp 0 packets, 0 bytes 30 second rate 0 bps Inspect Number of Half-open Sessions = 6 Half-open Sessions Session 83B5B920 (10.22.22.10:2135)=>(10.66.79.245:443) https:tcp SIS_OPENING Created 00:00:26, Last heard 00:00:26 Bytes sent (initiator:responder) [0:0] Session 83B5BB20 (10.66.79.241:138)=>(10.66.79.255:138) netbios-dgm:udp SIS_OPENING Created 00:00:26, Last heard 00:00:13 Bytes sent (initiator:responder) [406:0] Session 83B5BD20 (192.168.212.14:138)=>(192.168.212.255:138) netbios-dgm:udp SIS_OPENING Created 00:00:23, Last heard 00:00:23 Bytes sent (initiator:responder) [233:0] Session 83B5C120 (10.22.22.10:2138)=>(10.66.79.245:443) https:tcp SIS_OPENING Created 00:00:19, Last heard 00:00:19 Bytes sent (initiator:responder) [0:0] Session 83B5C320 (10.22.22.10:2142)=>(10.66.79.245:443) https:tcp SIS_OPENING Created 00:00:12, Last heard 00:00:12 Bytes sent (initiator:responder) [0:0] Session 83B5C520 (10.22.22.10:2145)=>(10.66.79.245:443) https:tcp SIS_OPENING Created 00:00:05, Last heard 00:00:05 Bytes sent (initiator:responder) [0:0] Class-map: class-default (match-any) Match: any Drop 0 packets, 0 bytes -
Router#show debugging
PPP: PPP authentication debugging is on PPP protocol negotiation debugging is on VPN: VPDN events debugging is on !--- When the PPTP User is connecting *Mar 13 02:22:40.535: VPDN Received L2TUN socket message <xCRQ - Session Incoming> *Mar 13 02:22:40.547: VPDN Tnl/Sn 2 2 L2TUN socket session accept requested *Mar 13 02:22:40.547: VPDN Tnl/Sn 2 2 Setting up dataplane for L2-L2, no idb *Mar 13 02:22:40.567: VPDN Received L2TUN socket message <xCCN - Session Connected> *Mar 13 02:22:40.595: VPDN uid:1 VPDN session up *Mar 13 02:22:40.607: ppp1 PPP: Send Message[Dynamic Bind Response] *Mar 13 02:22:40.607: ppp1 PPP: Using vpn set call direction *Mar 13 02:22:40.607: ppp1 PPP: Treating connection as a callin *Mar 13 02:22:40.607: ppp1 PPP: Session handle[8000003] Session id[1] *Mar 13 02:22:40.607: ppp1 PPP: Phase is ESTABLISHING, Passive Open *Mar 13 02:22:40.607: ppp1 LCP: State is Listen *Mar 13 02:22:42.563: ppp1 LCP: I CONFREQ [Listen] id 1 len 21 *Mar 13 02:22:42.563: ppp1 LCP: MRU 1400 (0x01040578) *Mar 13 02:22:42.563: ppp1 LCP: MagicNumber 0x069878CA (0x0506069878CA) *Mar 13 02:22:42.563: ppp1 LCP: PFC (0x0702) *Mar 13 02:22:42.563: ppp1 LCP: ACFC (0x0802) *Mar 13 02:22:42.563: ppp1 LCP: Callback 6 (0x0D0306) *Mar 13 02:22:42.563: ppp1 PPP: Authorization NOT required *Mar 13 02:22:42.563: ppp1 LCP: O CONFREQ [Listen] id 1 len 15 *Mar 13 02:22:42.563: ppp1 LCP: AuthProto CHAP (0x0305C22305) *Mar 13 02:22:42.563: ppp1 LCP: MagicNumber 0x14AF18DB (0x050614AF18DB) *Mar 13 02:22:42.563: ppp1 LCP: O CONFREJ [Listen] id 1 len 7 *Mar 13 02:22:42.563: ppp1 LCP: Callback 6 (0x0D0306) *Mar 13 02:22:42.567: ppp1 LCP: I CONFACK [REQsent] id 1 len 15 *Mar 13 02:22:42.567: ppp1 LCP: AuthProto CHAP (0x0305C22305) *Mar 13 02:22:42.567: ppp1 LCP: MagicNumber 0x14AF18DB (0x050614AF18DB) *Mar 13 02:22:42.567: ppp1 LCP: I CONFREQ [ACKrcvd] id 2 len 18 *Mar 13 02:22:42.567: ppp1 LCP: MRU 1400 (0x01040578) *Mar 13 02:22:42.567: ppp1 LCP: MagicNumber 0x069878CA (0x0506069878CA) *Mar 13 02:22:42.567: ppp1 LCP: PFC (0x0702) *Mar 13 02:22:42.567: ppp1 LCP: ACFC (0x0802) *Mar 13 02:22:42.567: ppp1 LCP: O CONFNAK [ACKrcvd] id 2 len 8 *Mar 13 02:22:42.567: ppp1 LCP: MRU 1500 (0x010405DC) *Mar 13 02:22:42.571: ppp1 LCP: I CONFREQ [ACKrcvd] id 3 len 18 *Mar 13 02:22:42.571: ppp1 LCP: MRU 1400 (0x01040578) *Mar 13 02:22:42.571: ppp1 LCP: MagicNumber 0x069878CA (0x0506069878CA) *Mar 13 02:22:42.571: ppp1 LCP: PFC (0x0702) *Mar 13 02:22:42.571: ppp1 LCP: ACFC (0x0802) *Mar 13 02:22:42.571: ppp1 LCP: O CONFNAK [ACKrcvd] id 3 len 8 *Mar 13 02:22:42.571: ppp1 LCP: MRU 1500 (0x010405DC) *Mar 13 02:22:42.571: ppp1 LCP: I CONFREQ [ACKrcvd] id 4 len 18 *Mar 13 02:22:42.571: ppp1 LCP: MRU 1500 (0x010405DC) *Mar 13 02:22:42.571: ppp1 LCP: MagicNumber 0x069878CA (0x0506069878CA) *Mar 13 02:22:42.571: ppp1 LCP: PFC (0x0702) *Mar 13 02:22:42.571: ppp1 LCP: ACFC (0x0802) *Mar 13 02:22:42.575: ppp1 LCP: O CONFACK [ACKrcvd] id 4 len 18 *Mar 13 02:22:42.575: ppp1 LCP: MRU 1500 (0x010405DC) *Mar 13 02:22:42.575: ppp1 LCP: MagicNumber 0x069878CA (0x0506069878CA) *Mar 13 02:22:42.575: ppp1 LCP: PFC (0x0702) *Mar 13 02:22:42.575: ppp1 LCP: ACFC (0x0802) *Mar 13 02:22:42.575: ppp1 LCP: State is Open *Mar 13 02:22:42.575: ppp1 PPP: Phase is AUTHENTICATING, by this end *Mar 13 02:22:42.575: ppp1 CHAP: O CHALLENGE id 1 len 33 from "Router" *Mar 13 02:22:42.575: ppp1 LCP: I IDENTIFY [Open] id 5 len 18 magic 0x069878CA MSRASV5.10 *Mar 13 02:22:42.579: ppp1 LCP: I IDENTIFY [Open] id 6 len 31 magic 0x069878CA MSRAS-0-WINXP-RIKNIGHT- *Mar 13 02:22:42.579: ppp1 CHAP: I RESPONSE id 1 len 26 from "cisco" *Mar 13 02:22:42.579: ppp1 PPP: Phase is FORWARDING, Attempting Forward *Mar 13 02:22:42.579: ppp1 PPP: Phase is AUTHENTICATING, Unauthenticated User *Mar 13 02:22:42.579: ppp1 PPP: Sent CHAP LOGIN Request *Mar 13 02:22:42.583: ppp1 PPP: Received LOGIN Response PASS *Mar 13 02:22:42.583: ppp1 PPP: Phase is FORWARDING, Attempting Forward *Mar 13 02:22:42.583: ppp1 PPP: Send Message[Connect Local] L2X_ADJ: Vi2.1:midchain adj reqd for ip 0.0.0.0, cid 0 L2X_ADJ: Vi2.1:midchain adj reqd for ip 0.0.0.0, cid 0 *Mar 13 02:22:42.619: VPDN Vi2.1 Virtual interface created for unknown, bandwidth 100000 Kbps *Mar 13 02:22:42.619: VPDN Vi2.1 Setting up dataplane for L2-L3, Vi2.1 *Mar 13 02:22:42.623: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up L2X_ADJ: Vi2.1:allocated ctx, size 1 *Mar 13 02:22:42.627: VPDN Received L2TUN socket message <Dataplane UP> *Mar 13 02:22:42.627: ppp1 PPP: Bind to [Virtual-Access2.1] *Mar 13 02:22:42.631: Vi2.1 PPP: Send Message[Static Bind Response] *Mar 13 02:22:42.631: Vi2.1 PPP: Phase is AUTHENTICATING, Authenticated User *Mar 13 02:22:42.631: Vi2.1 CHAP: O SUCCESS id 1 len 4 *Mar 13 02:22:42.635: Vi2.1 PPP: Phase is UP *Mar 13 02:22:42.639: Vi2.1 IPCP: O CONFREQ [Closed] id 1 len 10 *Mar 13 02:22:42.639: Vi2.1 IPCP: Address 10.66.79.73 (0x03060A424F49) *Mar 13 02:22:42.639: Vi2.1 PPP: Process pending ncp packets *Mar 13 02:22:42.643: Vi2.1 CCP: I CONFREQ [Not negotiated] id 7 len 10 *Mar 13 02:22:42.643: Vi2.1 CCP: MS-PPC supported bits 0x01000001 (0x120601000001) *Mar 13 02:22:42.643: Vi2.1 LCP: O PROTREJ [Open] id 2 len 16 protocol CCP (0x80FD0107000A120601000001) *Mar 13 02:22:42.643: Vi2.1 IPCP: I CONFREQ [REQsent] id 8 len 34 *Mar 13 02:22:42.643: Vi2.1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 13 02:22:42.643: Vi2.1 IPCP: PrimaryDNS 0.0.0.0 (0x810600000000) *Mar 13 02:22:42.643: Vi2.1 IPCP: PrimaryWINS 0.0.0.0 (0x820600000000) *Mar 13 02:22:42.643: Vi2.1 IPCP: SecondaryDNS 0.0.0.0 (0x830600000000) *Mar 13 02:22:42.643: Vi2.1 IPCP: SecondaryWINS 0.0.0.0 (0x840600000000) *Mar 13 02:22:42.643: Vi2.1 IPCP: Pool returned 192.168.100.1 *Mar 13 02:22:42.643: Vi2.1 IPCP: O CONFREJ [REQsent] id 8 len 28 *Mar 13 02:22:42.647: Vi2.1 IPCP: PrimaryDNS 0.0.0.0 (0x810600000000) *Mar 13 02:22:42.647: Vi2.1 IPCP: PrimaryWINS 0.0.0.0 (0x820600000000) *Mar 13 02:22:42.647: Vi2.1 IPCP: SecondaryDNS 0.0.0.0 (0x830600000000) *Mar 13 02:22:42.647: Vi2.1 IPCP: SecondaryWINS 0.0.0.0 (0x840600000000) *Mar 13 02:22:42.647: Vi2.1 IPCP: I CONFACK [REQsent] id 1 len 10 *Mar 13 02:22:42.647: Vi2.1 IPCP: Address 10.66.79.73 (0x03060A424F49) *Mar 13 02:22:42.647: Vi2.1 IPCP: I CONFREQ [ACKrcvd] id 9 len 10 *Mar 13 02:22:42.651: Vi2.1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 13 02:22:42.651: Vi2.1 IPCP: O CONFNAK [ACKrcvd] id 9 len 10 *Mar 13 02:22:42.651: Vi2.1 IPCP: Address 192.168.100.1 (0x0306C0A86401) *Mar 13 02:22:42.651: Vi2.1 IPCP: I CONFREQ [ACKrcvd] id 10 len 10 *Mar 13 02:22:42.651: Vi2.1 IPCP: Address 192.168.100.1 (0x0306C0A86401) *Mar 13 02:22:42.651: Vi2.1 IPCP: O CONFACK [ACKrcvd] id 10 len 10 *Mar 13 02:22:42.651: Vi2.1 IPCP: Address 192.168.100.1 (0x0306C0A86401) *Mar 13 02:22:42.651: Vi2.1 IPCP: State is Open L2X_ADJ: Vi2.1:adj notify change, event 2 L2X_ADJ: Vi2.1:midchain stacking IP 0.0.0.0 to 10.66.83.50 (VRF 0) L2X_ADJ: Vi2.1:adj notify change, event 8 L2X_ADJ: Vi2.1:adj notify change, event 3 *Mar 13 02:22:42.655: Vi2.1 IPCP: Install route to 192.168.100.1 *Mar 13 02:22:43.623: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to up !--- When the PPTP User is disconnecting *Mar 13 02:23:05.571: Vi2.1 LCP: I TERMREQ [Open] id 11 len 16 (0x069878CA003CCD7400000000) *Mar 13 02:23:05.571: Vi2.1 LCP: O TERMACK [Open] id 11 len 4 *Mar 13 02:23:05.575: Vi2.1 PPP: Sending Acct Event[Down] id[4] *Mar 13 02:23:05.575: Vi2.1 PPP: Phase is TERMINATING *Mar 13 02:23:05.779: VPDN Received L2TUN socket message <CDN - Session Disconnected> *Mar 13 02:23:05.779: VPDN Vi2.1 disconnect (AAA) IETF: 1/user-request Ascend: 28/PPP Receive Term *Mar 13 02:23:05.779: VPDN Vi2.1 vpdn shutdown session, result=2, error=6, vendor_err=0, syslog_error_code=2, syslog_key_type=1 *Mar 13 02:23:05.779: VPDN Vi2.1 VPDN/AAA: accounting stop sent *Mar 13 02:23:05.783: VPDN Vi2.1 Unbinding session from idb *Mar 13 02:23:05.783: Vi2.1 VPDN: Resetting interface *Mar 13 02:23:05.783: Vi2.1 PPP: Block vaccess from being freed [0x19] *Mar 13 02:23:05.783: Vi2.1 PPP: Received Disconnect from Lower Layer L2X_ADJ: Vi2.1:midchain unstacking IP 0.0.0.0 L2X_ADJ: Vi2.1:adj notify change, event 8 L2X_ADJ: Vi2.1:removed ctx *Mar 13 02:23:05.807: Vi2.1 LCP: State is Closed *Mar 13 02:23:05.807: Vi2.1 PPP: Phase is DOWN *Mar 13 02:23:05.807: Vi2.1 IPCP: State is Closed *Mar 13 02:23:05.807: Vi2.1 PPP: Unlocked by [0x1] Still Locked by [0x18] *Mar 13 02:23:05.807: Vi2.1 PPP: Unlocked by [0x10] Still Locked by [0x8] *Mar 13 02:23:05.811: Vi2.1 PPP: Unlocked by [0x8] Still Locked by [0x0] *Mar 13 02:23:05.811: Vi2.1 PPP: Free previously blocked vaccess
Troubleshoot
This section provides information you can use to troubleshoot your configuration.
-
Make sure that traffic destined to the Router allows for TCP port 1723 and GRE traffic.
-
Make sure that PPTP pass through traffic allows GRE through the Router.
-
Be careful of defect CSCsr41631; this is overcome with the use of different zones for the External interface and the Virtual-Template interface.
Related Information
Open a Support Case 
(Requires a Cisco Service Contract.)
Related Cisco Support Community Discussions
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.
Updated: May 18, 2009
Document ID: 110353