Cisco PIX 500 Series Security Appliances

Introduction

This sample configuration demonstrates how to set up the Cisco Security Appliances (PIX/ASA) for use on a single internal network.

For more information about the PIX/ASA Security Appliance Version 7.x and later with multiple internal networks that connect to the Internet (or an external network) with the command line interface (CLI) or Adaptive Security Device Manager (ASDM) 5.x and later, refer to PIX/ASA 7.x and later: Connecting Multiple Internal Networks with Internet Configuration Example.

Refer to ASA 8.3(x): Connect a Single Internal Network to the Internet for more information on identical configuration with Cisco Adaptive Security Appliance (ASA) with version 8.3 and later.

Before You Begin

Prerequisites

There are no specific prerequisites for this document.

Components Used

The information in this document is based on the software and hardware versions below.

• Cisco PIX Firewall Software Release 6.x and later

The information presented in this document was created from devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it.

Related Products

This configuration can also be used with the Cisco 5500 Series Adaptive Security Appliance, which runs version 7.x and later.

Conventions

For more information about document conventions, refer to Cisco Technical Tips Conventions.

Configure

In this section, you are presented with the information to configure the features described in this document.

Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only) .

Network Diagram

This document uses the network setup shown in the diagram below.

Note: The IP addressing schemes used in this configuration are not legally routable on the Internet. They are RFC 1918 addresses, which have been used in a lab environment.

PIX 6.x Configuration

This document uses the configurations shown below.

If you have the output of a write terminal command from your Cisco device, you can use to display potential issues and fixes. To use , you must be a registered customer, be logged in, and have JavaScript enabled.

• PIX 6.3 Configuration

• Router Configuration

• Configure PIX/ASA 7.x and Later

PIX Version 6.3(3)
nameif ethernet0 outside security0
nameif ethernet1 inside security100
nameif ethernet2 intf2 security10
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pixfirewall


!--- Output Suppressed




!--- Enable logging. 


logging on


!--- Output Suppressed




!--- All interfaces are shutdown by default. 


interface ethernet0 auto
interface ethernet1 auto
interface ethernet2 100full
mtu outside 1500
mtu inside 1500
mtu intf2 1500
ip address outside 10.165.200.226 255.255.255.224
ip address inside 10.1.1.1 255.255.255.0
ip address intf2 127.0.0.1 255.255.255.255
no failover   
failover timeout 0:00:00
failover ip address outside 0.0.0.0
failover ip address inside 0.0.0.0
failover ip address intf2 0.0.0.0
arp timeout 14400



!--- Output Suppressed




!--- Define a Network Address Translation (NAT) pool that
!--- internal hosts use when going out to the Internet.



global (outside) 1 10.165.200.227-10.165.200.254 netmask 255.255.255.224




!--- Allow all internal hosts to use 
!--- the NAT or PAT addresses specified previously.



nat (inside) 1 0.0.0.0 0.0.0.0 0 0



!--- Define a default route to the ISP router.


route outside 0.0.0.0 0.0.0.0 10.165.200.225 1


!--- Output Suppressed


: end         
[OK]

Building configuration...

Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname R3640_out
!
!
username cisco password 0 cisco
!
!
!
!
ip subnet-zero
ip domain-name cisco.com
!
isdn voice-call-failure 0
!

!
interface Ethernet0/1
 ip address 10.165.200.225 255.255.255.224
 no ip directed-broadcast

!
ip classless
no ip http server
!
!
line con 0
 exec-timeout 0 0
 length 0
 transport input none
line aux 0
line vty 0 4
 password ww
 login
!
end

Configure PIX/ASA 7.x and Later

Note: Nondefault commands are shown in bold.

pixfirewall# sh run
: Saved
:
PIX Version 8.0(2)
!
hostname pixfirewall
enable password 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0
 nameif outside
 security-level 0
 ip address 10.165.200.226 255.255.255.0
!
interface Ethernet1
 nameif inside
 security-level 100
 ip address 10.1.1.1 255.255.255.0
!


!--- Output Suppressed




!--- Enable logging.


logging enable




!--- Define a Network Address Translation (NAT) pool that
!--- internal hosts use when going out to the Internet.



global (outside) 1 10.165.200.227-10.165.200.254 netmask 255.255.255.2244



!--- Allow all internal hosts to use 
!--- the NAT or PAT addresses specified previously.


nat (inside) 1 0.0.0.0 0.0.0.0 0 0



!--- Define a default route to the ISP router.


route outside 0.0.0.0 0.0.0.0 10.165.200.225 1


!--- Output Suppressed


: end

NOTE:For more information about the configuration of NAT and PAT on PIX/ASA, refer to PIX/ASA 7.x NAT and PAT Statements.

For more information about the configuration of access lists on PIX/ASA, refer toPIX/ASA 7.x : Port Redirection (Forwarding) with nat, global, static and access-list Commands.

Verify

There is currently no verification procedure available for this configuration.

Troubleshoot

This section provides information you can use to troubleshoot your configuration.

NOTE:For more information about how to troubleshoot PIX/ASA, refer to Troubleshoot Connections through the PIX and ASA.

Certain show commands are supported by the Output Interpreter Tool (registered customers only) , which allows you to view an analysis of show command output.

Note: Before issuing debug commands, please see Important Information on Debug Commands.

• debug icmp trace - Shows whether ICMP requests from the hosts reach the PIX. To run this debug, you need to add the conduit permit icmp any any command to your configuration. However, when you have finished debugging, remove conduit permit icmp any any command to avoid security risks.

Related Information

• Cisco PIX Firewall Software
• Cisco PIX 500 Series Security Appliances
• Cisco ASA 5500 Series Adaptive Security Appliances
• PIX Command Reference
• Requests for Comments (RFCs)
• Technical Support & Documentation - Cisco Systems