Patch Upgrade Procedure for Cisco PGW 2200 Softswitch Release 9.6 and Later

Document ID: 48100

Updated: Jun 03, 2009

Download PDF

Cisco PGW 2200 Patch Upgrade Procedure

Related Information

Introduction

This document describes how to upgrade the Cisco PGW 2200 Softswitch Release 9.6 and later versions with new software patches.

Note: In older PGW 2200 versions, such as release 7.x, the upgrade process was performed with the Sun Solaris commands pkgadd and pkgrm. These Sun Solaris commands must not be issued with Cisco PGW 2200 Softswitch Release 9.2 and later versions. A new script called 'patch' does the job, as described in this document.

Prerequisites

Requirements

Cisco recommends that you have knowledge of these topics:

A new directory is created at the time of initial base software installation in Cisco PGW 2200 Softswitch Release 9.2 and later. The directory is called /opt/SW. The user is expected to download all new patches from the Voice Downloads (registered customers only) into this location. Also, a new shell script 'patch' is provided with the standard installation and is installed in the /opt/SW directory.

Here are the prerequisites for this procedure:

Note: Starting from 9.8(1) Patch 5, before the upgrade, make sure the TimesTen daemon is running on both active and standby Cisco PGW 2200 Softswitches. If the TimesTen daemon is not running, use the /etc/init.d/tt start command with the root privilege.
Note: Starting from 9.8(1) Patch 5, it is suggested that you use ./backupDb.sh ttbackup.tar on both active and standby Cisco PGW 2200 Softswitches in order to back up the TimesTen database before the upgrade. The script is located in the /opt/CiscoMGC/local folder.
Verify the directory /opt/SW is present on the active and the standby PGW 2200.
Verify that the two files called 'patch' and 'admin.file' are present in the directory /opt/SW.
Download the appropriate PGW 2200 patches from the Voice Downloads (registered customers only) to the /opt/SW directory in the active and the standby PGW 2200. Make sure the appropriate protocol and system patches are downloaded. Take a look at these:
Make sure that the decode<version_number>.pl file is downloaded from the Voice Downloads (registered customers only) to the /opt/SW directory.
Make sure that the two PGW 2200s do not synchronize their configurations during the upgrade.

In order to do this in both PGW 2200s, edit the file /opt/CiscoMGC/etc/XECfgParm.dat and set the parameter pom.dataSync to false. You must set pom.dataSync to false on the active and standby pair of Cisco PGW 2200 Softswitches before you perform the live upgrade. If you modify the pom.dataSync variable, make sure you save the file, /opt/CiscoMGC/etc/XECfgParm.dat. You do not have to restart the Cisco PGW 2200 Softswitch after the modification of this variable.

This ensures that one of the two PGW 2200s retains the old configuration and patch level, so that there is a way to return if something goes wrong.

Components Used

The information in this document is based on Cisco PGW 2200 Softswitch Release 9.7(3).

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

For more information on document conventions, refer to the Cisco Technical Tips Conventions.

Cisco PGW 2200 Patch Upgrade Procedure

The first step in this procedure is to upgrade the standby PGW 2200 with the new patches while you ensure the active PGW 2200 continues to carry the traffic until the standby is upgraded to the latest version.

Issue the rtrv-ne command in mml in order to check the status of the standby PGW 2200. The mml is the command line interface of the Cisco PGW 2200 Softswitch. Then verify that the current platform state is "STANDBY."

mgcusr@PGW2200-2% mml 

Copyright © 1998-2008, Cisco Systems, Inc. 

PGW2200-2> rtrv-ne 
   
   MGC-02 - Media Gateway Controller 2009-05-22 01:47:26.795 EDT
M  RTRV
   "Type:MGC"
   "Hardware platform:sun4u sparc SUNW,UltraAX-i2"
   "Vendor:"Cisco Systems, Inc.""
   "Location:MGC-01 - Media Gateway Controller"
   "Version:"9.7(3)""
   "Platform State:STANDBY"

PGW2200-2>

Issue the rtrv-alms and rtrv-softw:all commands in the mml, in order to check the alarm status and the software status..

If no error message is reported on software problems, proceed to step 3. Otherwise, try to understand the reason why the alarms are reported.

Exit the mml application. You can also shutdown the PGW 2200 application.

PGW2200-2> quit 
mgcusr@PGW2200% cd /etc/init.d 
mgcusr@PGW2200% pwd
/etc/init.d 
mgcusr@PGW2200-2% exit
login as: root
Using keyboard-interactive authentication.
Password:
Last login: Fri May 22 01:26:17 2009 from 10.1.1.1
Sun Microsystems Inc.   SunOS 5.10      Generic January 2005
# cd /etc/init.d#  ./CiscoMGC stop 

Signalling procM to shut down, with the pid = 1940
Sun Microsystems Inc.   SunOS 5.10      Generic January 2005
...shutdown complete

#

Check again to see if all processes on mgcusr are down. Issue the UNIX command ps -ef.
```
#ps -ef | grep mgcusr 
   
#
```
Before you install the new patches, check which patches you want to install at this time.

In the new naming convention, characters 5 and 6 describe the package contents, and the last three digits identify the patch number. For example, if the characters are equal to "012", this identifies the packages as Patch 12. In summary:

The protocol packages are labeled CSCOnnvvv:
- nn—Indicates the specific protocols you need for your environment.
- vvv—Indicates the version level of the patch.
An example of the patches for these protocol packages appears in this format:
```
CSCO30012 – Patch 12 for  protocol packages 30 
CSCO42012 – Patch 12 for  protocol packages 42 
```
Note: Install only the protocol patches you need. Issue the UNIX command pkginfo or the ./patch status command under directory /opt/SW to check this out.

Note: Make sure the appropriate protocol and system patches were downloaded from these:
Note: Refer to the Release Notes for the latest patches and patch download URLs.

For the Cisco PGW 2200 Softswitch Release 9.7(3), download the patches and scripts from the Software Download-Media Gateway Controller 9.7(3) Sparc Version. Create a folder, for example, s24p24, under /opt/SW directory to hold all the patch files. Copy all the downloaded patches and scripts to the /opt/SW/s24p24 directory. It must include these files:

C090703gs024.SPA
   C09070300024.SPA
   C09070301024.SPA
   C09070302024.SPA
   C09070310024.SPA
   C09070320024.SPA
   C09070330024.SPA
   C09070331024.SPA
   C09070332024.SPA
   C09070333024.SPA
   C09070340024.SPA
   C09070341024.SPA
   C09070342024.SPA
   C09070350024.SPA
   C09070360024.SPA
   C09070370024.SPA
   C09070371024.SPA
   C09070380024.SPA
   decode973sparc.pl
   patch973sparc.sh

Copy the admin.file to the folder you have created with this command:

cp /opt/SW/admin.file /opt/SW/s24p24

Under the /opt/SW/s24p24 directory, run perl decode973sparc.pl to decode encoded packages. You can choose to either decode the desired packages or decode all the packages at one time.

Note: For example, if you run this script with the package name, it decodes the assigned packages:
```
e.g. perl decode973sparc.pl C090703gs024.SPA
```
```
e.g. perl decode981sparc.pl C09080170005.SPA
```
Note: If you run this script with no package name under /opt/SW/s24p24, all the packages under this directory are decoded.
```
e.g. perl decode973sparc.pl
```
```
e.g. perl decode981sparc.pl
```
All the packages under this directory are renamed:
```
CSCOgs024.pkg
   CSCO00024.pkg
   CSCO01024.pkg
   CSCO02024.pkg
   CSCO10024.pkg
   CSCO20024.pkg
   CSCO30024.pkg
   CSCO31024.pkg
   CSCO32024.pkg
   CSCO33024.pkg
   CSCO40024.pkg
   CSCO41024.pkg
   CSCO42024.pkg
   CSCO50024.pkg
   CSCO60024.pkg
   CSCO70024.pkg
   CSCO71024.pkg
   CSCO80024.pkg
```

Check that the patch script, the admin.file, and the recently downloaded patches are in the /opt/SW/s24p24 directory.

In this example, you upgrade from PGW 2200 Softswitch Patch 12 to Patch 24.

mgcusr@PGW2200-2% pwd
/opt/SW/s24p24
mgcusr@PGW2200-2%  ls -al
total 1885378
drwxrwxr-x   2 mgcusr   mgcgrp      1024 May 18 02:47 .
drwxr-xr-x  13 root     sys          512 Jan  4  2008 ..
-rw-rw-r--   1 mgcusr   mgcgrp   93227520 May 15 01:49 CSCO00024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   21320192 May 15 02:53 CSCO01024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   9137152 May 15 03:05 CSCO02024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   49820672 May 15 05:18 CSCO10024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   76101632 May 15 03:11 CSCO20024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   61702144 May 15 05:03 CSCO30024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   61044224 May 15 05:08 CSCO31024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   79120384 May 15 05:13 CSCO32024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   62429184 May 15 05:13 CSCO33024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   60942336 May 15 01:50 CSCO40024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   69136896 May 15 01:52 CSCO41024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   17419776 May 15 02:49 CSCO42024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   53905920 May 15 02:54 CSCO50024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   31889920 May 15 02:53 CSCO60024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   52454912 May 15 02:59 CSCO70024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   47808512 May 15 03:05 CSCO71024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   35650048 May 15 03:20 CSCO80024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   81433088 May 15 03:29 CSCOgs024.pkg
-rwxrwxr-x   1 root     sys          205 Feb 16  2000 admin.file
-rw-rw-r--   1 mgcusr   mgcgrp      2150 Mar  9  2007 decode973sparc.pl
-rw-r--r--   1 root     other       1600 May 18 02:57 logs
-rwxrwxr-x   1 root     sys        16718 Jul 11  2008 patch973sparc.sh
mgcusr@PGW2200-2%



!--- This is the current patch level.


mgcusr@PGW2200-2% pkginfo | grep CSCO 

application CSCO00012      Cisco Media Gateway Controller Software 
                           core system protocols 
application CSCO01012      Cisco Media Gateway Controller Software 
                           Miscellaneous Protocols 
application CSCO02012      Cisco Media Gateway Controller Software 
                           Miscellaneous Protocols 
application CSCO10012      Cisco Media Gateway Controller Software 
                           SS7 family protocols 
application CSCO20012      Cisco Media Gateway Controller Software PRI 
                           family protocols 
application CSCO30012      Cisco Media Gateway Controller Software Q761 
                           Version 1 family  protocols 
application CSCO31012      Cisco Media Gateway Controller Software Q761 
                           Version 1 family protocols 
application CSCO32012      Cisco Media Gateway Controller Software Q761 
                           Version 1 family protocols 
application CSCO33012      Cisco Media Gateway Controller Software Q761 
                           Version 1 Family protocols 
application CSCO40012      Cisco Media Gateway Controller Software Q761 
                           Version 2 Protocol Family 
application CSCO41012      Cisco Media Gateway Controller Software Q761 
                           Version2 Protocol Family 
application CSCO42012      Cisco Media Gateway Controller Software Q761 
                           Version2 Protocol Family 
application CSCO50012      Cisco Media Gateway Controller Software Q761 
                           Version 3 Protocol Family 
application CSCO60012      Cisco Media Gateway Controller Software Q721 
                           Protocol Family 
application CSCO70012      Cisco Media Gateway Controller Software Q767 
                           Protocol Family 
application CSCO71012      Cisco Media Gateway Controller Software Q767 
                           Protocol Family 
application CSCO80012      Cisco Media Gateway Controller Software Q931 
                           Protocol Family 
application CSCOga000      Cisco Media Gateway Controller Software 
                           Licensing Components 
application CSCOga001      Cisco Media Gateway Controller Software 
                           Application 
application CSCOga002      Cisco Media Gateway Controller Software 
                           Database Components 
application CSCOga003      Cisco Media Gateway Controller Software 
                           SNMP Components 
application CSCOga004      Cisco Media Gateway Controller Software 
                           Toolkit Applications 
application CSCOga005      Cisco Media Gateway Controller Software 
                           Oracle/XML Parser tools 
application CSCOgc001      Cisco Media Gateway Controller Software  
                           Configuration & Data Migration 
application CSCOgd004      Cisco Media Gateway Controller Software 
                           SCTP Streams Module 
application CSCOgs012      Cisco Media Gateway Controller Software 
                           Patch Package 
application CSCOgt001      Cisco Media Gateway Controller Software 
                           Analyzer/Simulator 
utilities   CSCOgu000      Cisco Media Gateway Controller Software 
                           Common Utilities & Libraries 
utilities   CSCOh020       Media Gateway Controller Security package compatible with Solaris 10

utilities   CSCOh021       Media Gateway Controller Solaris 10 test for SPARC/Opteron

utilities   CSCOh022       Media Gateway Controller Solaris 10 Patch Cluster

utilities   CSCOh023       Media Gateway Controller Solaris 10 DiskSuite

utilities   CSCOh026       Media Gateway Controller PGW Specific Solaris 10 packages

Rename the script patch973sparc.sh to patch.

mgcusr@PGW2200-2%  mv patch973sparc.sh patch


mgcusr@PGW2200-2%  ls -al
total 1885378
drwxrwxr-x   2 mgcusr   mgcgrp      1024 May 18 02:47 .
drwxr-xr-x  13 root     sys          512 Jan  4  2008 ..
-rw-rw-r--   1 mgcusr   mgcgrp   93227520 May 15 01:49 CSCO00024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   21320192 May 15 02:53 CSCO01024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   9137152 May 15 03:05 CSCO02024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   49820672 May 15 05:18 CSCO10024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   76101632 May 15 03:11 CSCO20024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   61702144 May 15 05:03 CSCO30024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   61044224 May 15 05:08 CSCO31024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   79120384 May 15 05:13 CSCO32024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   62429184 May 15 05:13 CSCO33024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   60942336 May 15 01:50 CSCO40024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   69136896 May 15 01:52 CSCO41024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   17419776 May 15 02:49 CSCO42024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   53905920 May 15 02:54 CSCO50024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   31889920 May 15 02:53 CSCO60024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   52454912 May 15 02:59 CSCO70024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   47808512 May 15 03:05 CSCO71024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   35650048 May 15 03:20 CSCO80024.pkg
-rw-rw-r--   1 mgcusr   mgcgrp   81433088 May 15 03:29 CSCOgs024.pkg
-rwxrwxr-x   1 root     sys          205 Feb 16  2000 admin.file
-rw-rw-r--   1 mgcusr   mgcgrp      2150 Mar  9  2007 decode973sparc.pl
-rw-r--r--   1 root     other       1600 May 18 02:57 logs
-rwxrwxr-x   1 root     sys        16718 Jul 11  2008 patch

mgcusr@PGW2200-2%

For PGW releases 9.8(1)S5P5 and later, proceed to step 10. For all the previous versions, proceed to step 11.

Use the ./delete_replication.sh command on both active and standby Cisco PGW 2200 Softswitches in order to stop the TimesTen replication. The script is located in the /opt/CiscoMGC/local folder.

If there are no errors in step 9, start with the installation of the patches. Issue the ./patch all command under the /opt/SW/s24p24 directory.

You can choose to install the patch as given in the example below:

./patch all

!--- This will determine the most recent available patch,
 and automatically updates the system with that patch.

./patch system 024

!--- This will install the specified system patch

./patch protocol 024

!--- This will install the specified protocol patch

./patch system latest

!--- This will install the most recently downloaded system patch.

./patch protocol latest

!--- This will install the most recently downloaded protocol patch.

mgcusr@PGW2200-2% cd /opt/SW/s24p24

mgcusr@PGW2200-2% ./patch all 

 User [mgcusr] is still logged in or has running processes. 

 Processes: 
  5884 pts/1    0:01 tcsh 

 Please log [mgcusr] out or kill processes before uninstalling. 
  

#

Note: For patch installation, you need to log out as mgcusr and log in again as root.

mgcusr@PGW2200-2% exit
login as: root
Using keyboard-interactive authentication.
Password:
Last login: Fri May 22 01:26:17 2009 from 10.1.1.1
Sun Microsystems Inc.   SunOS 5.10      Generic January 2005# ./patch all 
The following patches are about to be removed from your system: 
CSCO00012 
CSCO01012 
CSCO02012 
CSCO10012 
CSCO20012 
CSCO30012 
CSCO31012 
CSCO32012 
CSCO33012 
CSCO40012 
CSCO41012 
CSCO42012 
CSCO50012 
CSCO60012 
CSCO70012 
CSCO71012 
CSCO80012 
CSCOgs012 

These patch(es) are about to be added to your system from the local directory:
CSCO00024.pkg
CSCO01024.pkg
CSCO02024.pkg
CSCO10024.pkg
CSCO20024.pkg
CSCO30024.pkg
CSCO31024.pkg
CSCO32024.pkg
CSCO33024.pkg
CSCO40024.pkg
CSCO41024.pkg
CSCO42024.pkg
CSCO50024.pkg
CSCO60024.pkg
CSCO70024.pkg
CSCO71024.pkg
CSCO80024.pkg
CSCOgs024.pkg
 
Are you sure this add/remove scenario is correct?  [y] [y,n,?,q] y 

Removal of <CSCO00012> was successful. 

Removal of <CSCO01012> was successful. 

Removal of <CSCO02012> was successful. 

Removal of <CSCO10012> was successful. 

Removal of <CSCO20012> was successful. 

Removal of <CSCO30012> was successful. 

Removal of <CSCO31012> was successful. 

Removal of <CSCO32012> was successful. 

Removal of <CSCO33012> was successful. 

Removal of <CSCO40012> was successful. 

Removal of <CSCO41012> was successful. 

Removal of <CSCO42012> was successful. 

Removal of <CSCO50012> was successful. 

Removal of <CSCO60012> was successful. 

Removal of <CSCO70012> was successful. 

Removal of <CSCO71012> was successful. 

Removal of <CSCO80012> was successful. 
Restoring saved /opt/CiscoMGC/bin/almM 
Restoring saved /opt/CiscoMGC/bin/amDmpr 
Restoring saved /opt/CiscoMGC/bin/ca 
Restoring saved /opt/CiscoMGC/bin/cdrDmpr 
Restoring saved /opt/CiscoMGC/bin/cfgM 
Restoring saved /opt/CiscoMGC/bin/converter 
Restoring saved /opt/CiscoMGC/bin/EISUP 
Restoring saved /opt/CiscoMGC/bin/engine.no_smartalloc 
Restoring saved /opt/CiscoMGC/bin/engine.smartalloc 
Restoring saved /opt/CiscoMGC/bin/foverd 
Restoring saved /opt/CiscoMGC/bin/get_trc.sh 
Restoring saved /opt/CiscoMGC/bin/ioChanMgr 
Restoring saved /opt/CiscoMGC/bin/ISDNIP 
Restoring saved /opt/CiscoMGC/bin/ISDNL3 
Restoring saved /opt/CiscoMGC/bin/IUA 
Restoring saved /opt/CiscoMGC/bin/LogServerd 
Restoring saved /opt/CiscoMGC/bin/M3UA 
Restoring saved /opt/CiscoMGC/bin/measMgr 
Restoring saved /opt/CiscoMGC/bin/MGCP 
Restoring saved /opt/CiscoMGC/bin/mml 
Restoring saved /opt/CiscoMGC/bin/mmSAgt 
Restoring saved /opt/CiscoMGC/bin/pom 
Restoring saved /opt/CiscoMGC/bin/procM 
Restoring saved /opt/CiscoMGC/bin/replicator 
Restoring saved /opt/CiscoMGC/bin/sagt 
Restoring saved /opt/CiscoMGC/bin/sim 
Restoring saved /opt/CiscoMGC/bin/simWriter 
Restoring saved /opt/CiscoMGC/bin/SIP 
Restoring saved /opt/CiscoMGC/bin/sp 
Restoring saved /opt/CiscoMGC/bin/SS7 
Restoring saved /opt/CiscoMGC/bin/SUA 
Restoring saved /opt/CiscoMGC/bin/TALI 
Restoring saved /opt/CiscoMGC/bin/TCAP 
Restoring saved /opt/CiscoMGC/lib/libcmg.so 
Restoring saved /opt/CiscoMGC/lib/libconvutil.so 
Restoring saved /opt/CiscoMGC/lib/libcxn.so 
Restoring saved /opt/CiscoMGC/lib/libda.so 
Restoring saved /opt/CiscoMGC/lib/libeng.so 
Restoring saved /opt/CiscoMGC/lib/libengif.so 
Restoring saved /opt/CiscoMGC/lib/libhelp.so 
Restoring saved /opt/CiscoMGC/lib/libinf.so 
Restoring saved /opt/CiscoMGC/lib/libpolbase.so 
Restoring saved /opt/CiscoMGC/lib/libpolcomp.so 
Restoring saved /opt/CiscoMGC/lib/libpolfiles.so 
Restoring saved /opt/CiscoMGC/lib/libpolnuman.so 
Restoring saved /opt/CiscoMGC/lib/libpolroute.so 
Restoring saved /opt/CiscoMGC/lib/libpom.so 
Restoring saved /opt/CiscoMGC/lib/libpxe.so 
Restoring saved /opt/CiscoMGC/lib/libpxelog.so 
Restoring saved /opt/CiscoMGC/lib/librmg.so 
Restoring saved /opt/CiscoMGC/lib/librudp.so 
Restoring saved /opt/CiscoMGC/lib/libsa.so 
Restoring saved /opt/CiscoMGC/lib/libxe.so 
Restoring saved /opt/CiscoMGC/local/config-lib 
Restoring saved /opt/CiscoMGC/local/migrateTKGFile 
Restoring saved /opt/CiscoMGC/etc/alarmCats.dat 
Restoring saved /opt/CiscoMGC/etc/extNodeTypes.dat 
Restoring saved /opt/CiscoMGC/etc/measCats.dat 
Restoring saved /opt/CiscoMGC/etc/mmlCommands.dat 
Restoring saved /opt/CiscoMGC/etc/propSet.xml.dat 
Restoring saved /opt/CiscoMGC/etc/propVal.xsd.dat 
Restoring saved /opt/CiscoMGC/etc/variant.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/alarmCats.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/extNodeTypes.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/measCats.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/mmlCommands.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/properties.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/propSet.xml.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/propVal.xsd.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/new/variant.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/alarmCats.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/extNodeTypes.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/measCats.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/mmlCommands.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/propSet.xml.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/propVal.xsd.dat 
Restoring saved /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/variant.dat 
Restoring saved /opt/CiscoMGC/etc/migrate/migrate_9.3001_9.4001 
Restoring saved /opt/CiscoMGC/etc/migrate/migrate_cpp_4_5 
Restoring saved /opt/CiscoMGC/etc/migrate/migrate_cpp_5_6 
Restoring saved /opt/CiscoMGC/.sw_config/mmlCommands.xml 
Backing out new file /opt/CiscoMGC/local/config-snmp 
Restoring saved /opt/Toolkit/bytecode/cdr/EntryLimit.tbc 
Restoring saved /opt/Toolkit/bytecode/cdr/File.tbc 
Restoring saved /opt/Toolkit/bytecode/cdr/position.dat 
Restoring saved /opt/Toolkit/bytecode/cdr/presentation.dat 
Restoring saved /opt/Toolkit/bytecode/cdr/search.tbc 
Restoring saved /opt/Toolkit/bytecode/toolbar/Toolbar.tbc 
Restoring saved /opt/Toolkit/bytecode/am/EntryLimit.tbc 
Restoring saved /opt/Toolkit/bytecode/XECfg/XECfgParm.tbc 

Removal of <CSCOgs012> was successful. 
Uncompressing ASP_NotRealProtocol.mdo
Uncompressing ASP_NotRealProtocol.so
Uncompressing CALLVER.mdo
Uncompressing CALLVER.so
Uncompressing CALLVER_GENERIC_ANALYSIS.mdo
Uncompressing CALLVER_GENERIC_ANALYSIS.so
Uncompressing CALLVER_LCM.mdo
Uncompressing CDR_MAN.mdo
Uncompressing CDR_MAN.so
Uncompressing CONNECTION_PLANE_MANAGER.mdo
Uncompressing CONNECTION_PLANE_MANAGER.so
Uncompressing EISUP.mdo
Uncompressing EISUP.so
Uncompressing EISUP_96VER.mdo
Uncompressing EISUP_96VER.so
Uncompressing ETS_300_172_SLAVE.mdo
Uncompressing ETS_300_172_SLAVE.so
Uncompressing GENERIC_ANALYSIS.mdo
Uncompressing GENERIC_ANALYSIS.so
Uncompressing IN_TRIGGER.mdo
Uncompressing IN_TRIGGER.so
Uncompressing LEG_CONTROLLER.mdo
Uncompressing LEG_CONTROLLER.so
Uncompressing LEG_CONTROLLER_H248V2.mdo
Uncompressing LEG_CONTROLLER_H248V2.so
Uncompressing LEG_CONTROLLER_MGCP.mdo
Uncompressing LEG_CONTROLLER_MGCP.so
Uncompressing cc.mdo
Uncompressing cc.so
Uncompressing dummy.mdo
Uncompressing dummy.so
Uncompressing lcm.mdo
Uncompressing lcm.so

Installation of <CSCO00024> was successful.
Uncompressing BTNUP_BTNR167.mdo
Uncompressing BTNUP_BTNR167.so

Uncompressing BTNUP_IUP.mdo
Uncompressing BTNUP_IUP.so
Uncompressing DPNSS_BTNR188.mdo
Uncompressing DPNSS_BTNR188.so
Uncompressing QBE.mdo
Uncompressing QBE.so 

Installation of <CSCO01024> was successful.
Uncompressing IETF_SIP.mdo
Uncompressing IETF_SIP.so

Installation of <CSCO02024> was successful.
Uncompressing ANSISS7_2K.mdo
Uncompressing ANSISS7_2K.so
Uncompressing ANSISS7_92.mdo
Uncompressing ANSISS7_92.so
Uncompressing ANSISS7_C2.mdo
Uncompressing ANSISS7_C2.so
Uncompressing ANSISS7_C3.mdo
Uncompressing ANSISS7_C3.so
Uncompressing ANSISS7_E1.mdo
Uncompressing ANSISS7_E1.so
Uncompressing ANSISS7_STANDARD.mdo
Uncompressing ANSISS7_STANDARD.so
Uncompressing GR317.mdo
Uncompressing GR317.so

Installation of <CSCO10024> was successful.
Uncompressing ATT_41459.mdo
Uncompressing ATT_41459.so
Uncompressing ATT_41459_C2.mdo
Uncompressing ATT_41459_C2.so
Uncompressing BELL_1268.mdo
Uncompressing BELL_1268.so
Uncompressing BELL_1268_C2.mdo
Uncompressing BELL_1268_C2.so
Uncompressing ETS_300_102.mdo
Uncompressing ETS_300_102.so
Uncompressing ETS_300_102_C2.mdo
Uncompressing ETS_300_102_C2.so
Uncompressing ETS_300_172.mdo
Uncompressing ETS_300_172.so

Installation of <CSCO20024> was successful. 
Uncompressing ETS_300_121.mdo
Uncompressing ETS_300_121.so
Uncompressing ETS_300_356.mdo
Uncompressing ETS_300_356.so
Uncompressing HONGKONG.mdo
Uncompressing HONGKONG.so
Uncompressing ISUPV1_POLI.mdo
Uncompressing ISUPV1_POLI.so
Uncompressing Q761_ARGENTINA.mdo
Uncompressing Q761_ARGENTINA.so
Uncompressing Q761_ARGENTINA_C2.mdo
Uncompressing Q761_ARGENTINA_C2.so
Uncompressing Q761_AUSTRL.mdo
Uncompressing Q761_AUSTRL.so
Uncompressing Q761_AUSTRL_C2.mdo
Uncompressing Q761_AUSTRL_C2.so

Installation of <CSCO30024> was successful.
Uncompressing Q761_BASE.mdo
Uncompressing Q761_BASE.so
Uncompressing Q761_BELG.mdo
Uncompressing Q761_BELG.so
Uncompressing Q761_BELG_97VER.mdo
Uncompressing Q761_BELG_97VER.so
Uncompressing Q761_CHILE.mdo
Uncompressing Q761_CHILE.so
Uncompressing Q761_CHINA.mdo
Uncompressing Q761_CHINA.so
Uncompressing Q761_CHINA_C2.mdo
Uncompressing Q761_CHINA_C2.so
Uncompressing Q761_DANISH.mdo
Uncompressing Q761_DANISH.so

Installation of <CSCO31024> was successful. 
Uncompressing Q761_97VER_BASE.mdo
Uncompressing Q761_97VER_BASE.so
Uncompressing Q761_97VER_RUSS.mdo
Uncompressing Q761_97VER_RUSS.so
Uncompressing Q761_97VER_RUSS_C2.mdo
Uncompressing Q761_97VER_RUSS_C2.so
Uncompressing Q761_GERMAN.mdo
Uncompressing Q761_GERMAN.so
Uncompressing Q761_INDIA.mdo
Uncompressing Q761_INDIA.so
Uncompressing Q761_KOREAN.mdo
Uncompressing Q761_KOREAN.so
Uncompressing Q761_NEWZEALAND.mdo
Uncompressing Q761_NEWZEALAND.so
Uncompressing Q761_PERU.mdo
Uncompressing Q761_PERU.so
Uncompressing Q761_PORTUGAL.mdo
Uncompressing Q761_PORTUGAL.so

Installation of <CSCO32024> was successful. 
Uncompressing Q761_99VER_AUSTRL_C3.mdo
Uncompressing Q761_99VER_AUSTRL_C3.so
Uncompressing Q761_99VER_BASE.mdo
Uncompressing Q761_99VER_BASE.so
Uncompressing Q761_MALAYSIAN.mdo
Uncompressing Q761_MALAYSIAN.so
Uncompressing Q761_SINGAPORE.mdo
Uncompressing Q761_SINGAPORE.so
Uncompressing Q761_SINGAPORE_C2.mdo
Uncompressing Q761_SINGAPORE_C2.so
Uncompressing Q761_TAIWAN.mdo
Uncompressing Q761_TAIWAN.so
Uncompressing Q761_THAILAND.mdo
Uncompressing Q761_THAILAND.so

Installation of <CSCO33024> was successful. 
Uncompressing ISUPV2_AUSTRIAN.mdo
Uncompressing ISUPV2_AUSTRIAN.so
Uncompressing ISUPV2_CZECH.mdo
Uncompressing ISUPV2_CZECH.so
Uncompressing ISUPV2_DUTCH.mdo
Uncompressing ISUPV2_DUTCH.so
Uncompressing ISUPV2_FINNISH96.mdo
Uncompressing ISUPV2_FINNISH96.so
Uncompressing ISUPV2_FRENCH.mdo
Uncompressing ISUPV2_FRENCH.so
Uncompressing ISUPV2_GERMAN.mdo
Uncompressing ISUPV2_GERMAN.so
Uncompressing ISUPV2_ISRAEL.mdo
Uncompressing ISUPV2_ISRAEL.so

Installation of <CSCO40024> was successful. 
Uncompressing ISUPV2_JAPAN.mdo
Uncompressing ISUPV2_JAPAN.so
Uncompressing ISUPV2_JAPAN_C2.mdo
Uncompressing ISUPV2_JAPAN_C2.so
Uncompressing ISUPV2_NORWEGIAN.mdo
Uncompressing ISUPV2_NORWEGIAN.so
Uncompressing ISUPV2_POLISH.mdo
Uncompressing ISUPV2_POLISH.so
Uncompressing ISUPV2_SPANISH.mdo
Uncompressing ISUPV2_SPANISH.so
Uncompressing ISUPV2_SPANISH_C2.mdo
Uncompressing ISUPV2_SPANISH_C2.so
Uncompressing ISUPV2_SWISS.mdo
Uncompressing ISUPV2_SWISS.so
Uncompressing ISUPV2_SWISS_C2.mdo
Uncompressing ISUPV2_SWISS_C2.so

Installation of <CSCO41024> was successful. 
Uncompressing ISUPV2_AUSTRIAN_C2.mdo
Uncompressing ISUPV2_AUSTRIAN_C2.so
Uncompressing ISUPV2_VIETNAM.mdo
Uncompressing ISUPV2_VIETNAM.so

Installation of <CSCO42024> was successful. 
Uncompressing ISUPV3.mdo
Uncompressing ISUPV3.so
Uncompressing ISUPV3_FRENCH.mdo
Uncompressing ISUPV3_FRENCH.so
Uncompressing ISUPV3_UK.mdo
Uncompressing ISUPV3_UK.so
Uncompressing ISUPV3_UK_C2.mdo
Uncompressing ISUPV3_UK_C2.so
Uncompressing ISUPV3_UK_C3.mdo
Uncompressing ISUPV3_UK_C3.so
Uncompressing ISUPV3_UK_C4.mdo
Uncompressing ISUPV3_UK_C4.so

Installation of <CSCO50024> was successful.
Uncompressing Q721_BASE.mdo
Uncompressing Q721_BASE.so
Uncompressing Q721_BRAZILIAN.mdo
Uncompressing Q721_BRAZILIAN.so
Uncompressing Q721_BRAZILIAN_C2.mdo
Uncompressing Q721_BRAZILIAN_C2.so
Uncompressing Q721_CHINA.mdo
Uncompressing Q721_CHINA.so
Uncompressing Q721_FRENCH.mdo
Uncompressing Q721_FRENCH.so
Uncompressing Q721_PHILLIPINE.mdo
Uncompressing Q721_PHILLIPINE.so

Installation of <CSCO60024> was successful.
Uncompressing Q767_AUSTRALIA.mdo
Uncompressing Q767_AUSTRALIA.so
Uncompressing Q767_BASE.mdo
Uncompressing Q767_BASE.so
Uncompressing Q767_BRAZIL.mdo
Uncompressing Q767_BRAZIL.so
Uncompressing Q767_BRAZIL_C2.mdo
Uncompressing Q767_BRAZIL_C2.so
Uncompressing Q767_COLOMBIA.mdo
Uncompressing Q767_COLOMBIA.so
Uncompressing Q767_GUATEMALA.mdo
Uncompressing Q767_GUATEMALA.so
Uncompressing Q767_INDONESIA.mdo
Uncompressing Q767_INDONESIA.so
Uncompressing Q767_ITAL.mdo
Uncompressing Q767_ITAL.so
Uncompressing Q767_ITAL_C2.mdo
Uncompressing Q767_ITAL_C2.so

Installation of <CSCO70024> was successful. 
Uncompressing Q767_MEXICAN.mdo
Uncompressing Q767_MEXICAN.so
Uncompressing Q767_NIGERIAN.mdo
Uncompressing Q767_NIGERIAN.so
Uncompressing Q767_RUSS.mdo
Uncompressing Q767_RUSS.so
Uncompressing Q767_RUSS_C2.mdo
Uncompressing Q767_RUSS_C2.so
Uncompressing Q767_SINGAPORE.mdo
Uncompressing Q767_SINGAPORE.so
Uncompressing Q767_SPAN.mdo
Uncompressing Q767_SPAN.so
Uncompressing Q767_SWED.mdo
Uncompressing Q767_SWED.so
Uncompressing Q767_TURKISH.mdo
Uncompressing Q767_TURKISH.so

Installation of <CSCO71024> was successful.
Uncompressing Q931.mdo
Uncompressing Q931.so
Uncompressing Q931_AUSTRALIA.mdo
Uncompressing Q931_AUSTRALIA.so
Uncompressing Q931_SINGAPORE.mdo
Uncompressing Q931_SINGAPORE.so

Installation of <CSCO80024> was successful. 
Uncompressing EISUP 
Uncompressing ISDNIP 
Uncompressing ISDNL3 
Uncompressing IUA 
Uncompressing LogServerd 
Uncompressing M3UA 
Uncompressing MGCP 
Uncompressing SIP 
Uncompressing SS7 
Uncompressing SUA 
Uncompressing TALI 
Uncompressing TCAP 
Uncompressing almM 
Uncompressing amDmpr 
Installing ca 
Uncompressing cdrDmpr 
Uncompressing cfgM 
Uncompressing converter 
Installing engine.no_smartalloc 
Installing engine.smartalloc 
Uncompressing foverd 
Installing get_trc.sh 
Uncompressing ioChanMgr 
Uncompressing measMgr 
Uncompressing mmSAgt 
Uncompressing mml 
Uncompressing pom 
Uncompressing procM 
Uncompressing replicator 
Uncompressing sagt 
Installing sim 
Installing simWriter 
Installing sp 
Installing alarmCats.dat 
Installing extNodeTypes.dat 
Installing measCats.dat 
Installing mmlCommands.dat 
Installing propSet.xml.dat 
Installing propVal.xsd.dat 
Installing variant.dat 
Installing alarmCats.dat 
Installing extNodeTypes.dat 
Installing measCats.dat 
Installing mmlCommands.dat 
Installing propSet.xml.dat 
Installing propVal.xsd.dat 
Installing properties.dat 
Installing variant.dat 
Installing alarmCats.dat 
Installing extNodeTypes.dat 
Installing measCats.dat 
Installing migrate_cpp_4_5 
Installing migrate_cpp_5_6 
Installing mmlCommands.dat 
Installing propSet.xml.dat 
Installing propVal.xsd.dat 
Installing variant.dat 
Installing libcmg.so 
Installing libconvutil.so 
Installing libcxn.so 
Installing libda.so 
Installing libeng.so 
Installing libengif.so 
Installing libhelp.so 
Installing libinf.so 
Installing libpolbase.so 
Installing libpolcomp.so 
Installing libpolfiles.so 
Installing libpolnuman.so 
Installing libpolroute.so 
Uncompressing libpom.so 
Uncompressing libpxe.so 
Uncompressing libpxelog.so 
Installing librmg.so 
Uncompressing librudp.so 
Installing libsa.so 
Uncompressing libxe.so 
Installing libexpect5.32.so 
Updating parameters for CiscoMGC 
Updating parameters for mmlCommands.xml 
Updating parameters for migrate_9.3001_9.4001 
Updating parameters for .dump-prov 
Updating parameters for .master.cks 
Updating parameters for config-lib 
Updating parameters for config-snmp 
Updating parameters for delete_replication.sh 
Updating parameters for migrateTKGFile 
Updating /opt/CiscoMGC/bin/almM 
Updating /opt/CiscoMGC/bin/amDmpr 
Updating /opt/CiscoMGC/bin/ca 
Updating /opt/CiscoMGC/bin/cdrDmpr 
Updating /opt/CiscoMGC/bin/cfgM 
Updating /opt/CiscoMGC/bin/converter 
Updating /opt/CiscoMGC/bin/EISUP 
Updating /opt/CiscoMGC/bin/engine.no_smartalloc 
Updating /opt/CiscoMGC/bin/engine.smartalloc 
Updating /opt/CiscoMGC/bin/foverd 
Updating /opt/CiscoMGC/bin/get_trc.sh 
Updating /opt/CiscoMGC/bin/ioChanMgr 
Updating /opt/CiscoMGC/bin/ISDNIP 
Updating /opt/CiscoMGC/bin/ISDNL3 
Updating /opt/CiscoMGC/bin/IUA 
Updating /opt/CiscoMGC/bin/LogServerd 
Updating /opt/CiscoMGC/bin/M3UA 
Updating /opt/CiscoMGC/bin/measMgr 
Updating /opt/CiscoMGC/bin/MGCP 
Updating /opt/CiscoMGC/bin/mml 
Updating /opt/CiscoMGC/bin/mmSAgt 
Updating /opt/CiscoMGC/bin/pom 
Updating /opt/CiscoMGC/bin/procM 
Updating /opt/CiscoMGC/bin/replicator 
Updating /opt/CiscoMGC/bin/sagt 
Updating /opt/CiscoMGC/bin/sim 
Updating /opt/CiscoMGC/bin/simWriter 
Updating /opt/CiscoMGC/bin/SIP 
Updating /opt/CiscoMGC/bin/sp 
Updating /opt/CiscoMGC/bin/SS7 
Updating /opt/CiscoMGC/bin/SUA 
Updating /opt/CiscoMGC/bin/TALI 
Updating /opt/CiscoMGC/bin/TCAP 
Updating /opt/CiscoMGC/etc/alarmCats.dat 
Updating /opt/CiscoMGC/etc/extNodeTypes.dat 
Updating /opt/CiscoMGC/etc/measCats.dat 
Updating /opt/CiscoMGC/etc/mmlCommands.dat 
Updating /opt/CiscoMGC/etc/propSet.xml.dat 
Updating /opt/CiscoMGC/etc/propVal.xsd.dat 
Updating /opt/CiscoMGC/etc/variant.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/alarmCats.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/extNodeTypes.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/measCats.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/mmlCommands.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/properties.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/propSet.xml.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/propVal.xsd.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/new/variant.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/alarmCats.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/extNodeTypes.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/measCats.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/mmlCommands.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/propSet.xml.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/propVal.xsd.dat 
Updating /opt/CiscoMGC/etc/CONFIG_LIB/CFG_sgp2/variant.dat 
Updating /opt/CiscoMGC/etc/migrate/migrate_9.3001_9.4001 
Updating /opt/CiscoMGC/etc/migrate/migrate_cpp_4_5 
Updating /opt/CiscoMGC/etc/migrate/migrate_cpp_5_6 
Updating /opt/CiscoMGC/lib/libcmg.so 
Updating /opt/CiscoMGC/lib/libconvutil.so 
Updating /opt/CiscoMGC/lib/libcxn.so 
Updating /opt/CiscoMGC/lib/libda.so 
Updating /opt/CiscoMGC/lib/libeng.so 
Updating /opt/CiscoMGC/lib/libengif.so 
Updating /opt/CiscoMGC/lib/libhelp.so 
Updating /opt/CiscoMGC/lib/libinf.so 
Updating /opt/CiscoMGC/lib/libpolbase.so 
Updating /opt/CiscoMGC/lib/libpolcomp.so 
Updating /opt/CiscoMGC/lib/libpolfiles.so 
Updating /opt/CiscoMGC/lib/libpolnuman.so 
Updating /opt/CiscoMGC/lib/libpolroute.so 
Updating /opt/CiscoMGC/lib/libpom.so 
Updating /opt/CiscoMGC/lib/libpxe.so 
Updating /opt/CiscoMGC/lib/libpxelog.so 
Updating /opt/CiscoMGC/lib/librmg.so 
Updating /opt/CiscoMGC/lib/librudp.so 
Updating /opt/CiscoMGC/lib/libsa.so 
Updating /opt/CiscoMGC/lib/libxe.so 
Updating /opt/CiscoMGC/local/config-lib 
Updating /opt/CiscoMGC/local/config-snmp 
Updating /opt/CiscoMGC/local/delete_replication.sh 
Updating /opt/CiscoMGC/local/migrateTKGFile 
Updating /opt/CiscoMGC/snmp/measurement.my 
Updating /opt/CiscoMGC/snmp/snmpinfo.dat 
Updating /opt/CiscoMGC/.sw_config/mmlCommands.xml 
Updating /opt/Toolkit/bytecode/cdr/EntryLimit.tbc 
Updating /opt/Toolkit/bytecode/cdr/File.tbc 
Updating /opt/Toolkit/bytecode/cdr/position.dat 
Updating /opt/Toolkit/bytecode/cdr/presentation.dat 
Updating /opt/Toolkit/bytecode/cdr/search.tbc 
Updating /opt/Toolkit/bytecode/toolbar/Toolbar.tbc 
Updating /opt/Toolkit/bytecode/log/EntryLimit.tbc 
Updating /opt/Toolkit/bytecode/log/File.tbc 
Updating /opt/Toolkit/bytecode/am/AlarmView.tbc 
Updating /opt/Toolkit/bytecode/am/EntryLimit.tbc 
Updating /opt/Toolkit/bytecode/tv/EntryLimit.tbc 
Updating /opt/Toolkit/bytecode/XECfg/XECfgParm.tbc 

Update proc-setid core flag.
Done.

Installation of <CSCOgs024> was successful 
#

After successful installation of all patches, restart the PGW 2200 Softswitch application and check to make sure that all processes are up and running correctly.

# 
# cd /etc/init.d 
# ./CiscoMGC start
Application started 
# 
# ps -ef | grep mgcusr 
  
  root  1967 16890   0 06:02:30 pts/1       0:00 grep mgcusr
  mgcusr  1961  1940   1 06:02:11 ?           0:00 ../bin/mmdbd -X 30007
  mgcusr  1944  1940   1 06:02:03 ?           0:00 ../bin/cdrDmpr -X 30005
  mgcusr  1951  1940   1 06:02:06 ?           0:00 ../bin/replicator -X 3000d -C ../etc/XECfgParm.dat -t
  mgcusr  1963  1940   1 06:02:12 ?           0:01 ../bin/TCAP -X 30010
  mgcusr  1947  1940   1 06:02:04 ?           0:01 ../bin/pom -X 30008
  mgcusr  1948  1940   1 06:02:04 ?           0:00 ../bin/diskmonitor -X 30006
  mgcusr  1950  1940   3 06:02:06 ?           0:02 ../bin/engine -X 3000e
  mgcusr  1946  1940   1 06:02:04 ?           0:00 ../bin/measMgr -X 30003
  mgcusr  1940     1   1 06:01:58 ?           0:00 procM
  mgcusr  1945  1940   1 06:02:03 ?           0:00 ../bin/cfgM -X 30001
  mgcusr  1931     1   0 06:01:57 ?           0:00 ../bin/LogServerd -d
  mgcusr  1943  1940   1 06:02:03 ?           0:00 ../bin/amDmpr -X 30004

# exit

Use the mml command in order to check the PGW 2200 Softswitch STANDBY status.

Note: After you restart the PGW 2200 Softswitch, the STATUS can be OOS for up to a couple of minutes. But then the status changes to STANDBY. If this is not the case, try to check the system with an mml command. You can issue the rtrv-softw:all and rtrv-alms commands, for example.

mgcusr@PGW2200-2% mml 

Copyright © 1998-2008, Cisco Systems, Inc.
PGW2200-2 mml> rtrv-ne 
   
   ;
   MGC-02 - Media Gateway Controller 2009-05-22 02:17:58.091 EDT
M  RTRV
   "Type:MGC"
   "Hardware platform:sun4u sparc SUNW,UltraAX-i2"
   "Vendor:"Cisco Systems, Inc.""
   "Location:MGC-02 - Media Gateway Controller"
   "Version:"9.7(3)""
   "Platform State:STANDBY"
 
PGW2200-2 mml>

Check the software and alarm status:

PGW2200-2 mml> rtrv-softw:all 
  
  MGC-02 - Media Gateway Controller 2009-05-22 02:19:14.006 EDT
M  RTRV 
   "CFM-01:RUNNING STANDBY" 
   "ALM-01:RUNNING STANDBY" 
   "MM-01:RUNNING STANDBY" 
   "AMDMPR-01:RUNNING STANDBY" 
   "CDRDMPR-01:RUNNING STANDBY" 
   "DSKM-01:RUNNING IN N/A STATE" 
   "MMDB-01:RUNNING IN N/A STATE" 
   "POM-01:RUNNING STANDBY" 
   "MEASAGT:RUNNING STANDBY" 
   "OPERSAGT:RUNNING STANDBY" 
   "mgcp-1:RUNNING IN N/A STATE" 
   "Replic-01:RUNNING STANDBY" 
   "ENG-01:RUNNING STANDBY" 
   "IOCM-01:RUNNING STANDBY" 
   "TCAP-01:RUNNING IN N/A STATE" 
   "m3ua-1:RUNNING IN N/A STATE" 
   "FOD-01:RUNNING IN N/A STATE

PGW2200-2 mml> rtrv-alms 
PGW2200-2 mml> quit 
mgcusr@PGW2200%

In case of other problems, check the messages in the /opt/CiscoMGC/var/log/platform.log file. If you are not able to solve the problem, open a case with the Cisco Technical Assistance Center (TAC) and include the capture file of the upgrade patch process, in combination with the platform.log information.

Note: Do not upgrade the active system with the new patch level until the problem has been analyzed. If everything is all right, proceed to step 16.

Perform the same process again for the PGW 2200 Softswitch that is currently active. First switch over the active PGW to standby status:

PGW2200-1 mml> rtrv-ne 
MGC-02 - Media Gateway Controller 2009-05-22 02:17:58.091 EDT
M  RTRV
   "Type:MGC"
   "Hardware platform:sun4u sparc SUNW,UltraAX-i2"
   "Vendor:"Cisco Systems, Inc.""
   "Location:MGC-02 - Media Gateway Controller"
   "Version:"9.7(3)""
   "Platform State:ACTIVE"
   ; 
PGW2200-1> 
PGW2200-1> sw-over::confirm 
   MGC-02 - Media Gateway Controller 2004-01-28 09:56:56.883 GMT 
M  COMPLD 
   "Proc Mgr" 
   ; 
PGW2200-1 mml> 

!--- Note: The system comes into OOS 
!--- status for some time until the system comes to the final 
!--- Standby status. Do a rtrv-ne several times 
!--- in order to find out the final status. If the status still remains
!--- in OOS, check the PGW 2200 alarm status 
!--- with rtrv-alms. 


PGW2200-1 mml> rtrv-ne
 MGC-02 - Media Gateway Controller 2009-05-22 02:17:58.091 EDT
M  RTRV
   "Type:MGC"
   "Hardware platform:sun4u sparc SUNW,UltraAX-i2"
   "Vendor:"Cisco Systems, Inc.""
   "Location:MGC-02 - Media Gateway Controller"
   "Version:"9.7(3)""
   "Platform State:STANDBY"
PGW2200-1 mml>

Note: Check PGW2200-2, if this system is in ACTIVE mode.

If the system is in STANDBY mode, go to step 1 again and upgrade PGW 2200-1 with the new patches.

For PGW releases 9.8(1)S5P5 and later, proceed to step 18. For all the previous versions, proceed to step 19.
Start the TimesTen replication on the active and standby pair of Cisco PGW 2200 Softswitches. Refer to the Initializing Database Replication section of the Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide for more information and instructions on how to start the replication.
After both PGW 2200 Softswitches have been upgraded, edit the /opt/CiscoMGC/etc/XECfgParm.dat file in both PGW 2200 Softswitches and set the parameter pom.dataSync to true in order to restore configuration synchronization.