Feedback
Contents
Command Reference
This appendix contains necessary information on disk space management for all types of Cisco Prime Infrastructure deployments and an alphabetical listing of the commands specific to the Prime Infrastructure. The Prime Infrastructure comprise the following modes:
Each of the commands in this appendix is followed by a brief description of its use, command syntax, any command defaults, command modes, usage guidelines, and one or more examples. Throughout this appendix, the Prime Infrastructure server uses the name ncs in place of the Prime Infrastructure server’s hostname.
NoteIf an error occurs in any command usage, use the debug command to determine the cause of the error.
Disk Space Management in Prime Infrastructure
This section provides information on disk space in the Prime Infrastructure appliances for all types of deployments. Each of the Prime Infrastructure appliances has a different amount of disk space, and managing that disk space is important to enable you to use the Prime Infrastructure efficiently.
Before proceeding to use the Prime Infrastructure CLI commands, familiarize yourself with disk space management in the Prime Infrastructure appliances. You can deploy the Prime Infrastructure on appliances with small, medium and large form factors and VMware. Table A-1 provides information on Prime Infrastructure appliances on all of the form factors and the available disk space that you need to manage the Prime Infrastructure.
Table A-2 lists the disk space that you may use on the /var partition that has a total of 6 GB of disk space. You may use 308 MB of the 6 GB of disk space for the operating system and the Cisco ADE OS 2.0 log files. You can then use the remaining 5.7 GB of disk space for a medium and large type deployment.
All of the files that you create in the Prime Infrastructure reside in the /opt partition. You must manage the disk space for the files that you create in the /opt partition so that the files increase in size within the limits that do not have an impact on other files and services in the system.
Table A-3 lists the disk space that you may use on the /opt partition that has a total of 410 GB of disk space. You may use 161 GB of disk space and the remaining of 249 GB for a medium and large type deployment. The remaining 249 GB of disk space can be better utilized for the database growth after you consider the disk space required for backup, restore, and replication.
For detailed information on logging into the Prime Infrastructure, refer to the Cisco Prime Network Control System Configuration Guide, Release 2.0.
EXEC Commands
- application install
- application remove
- application reset-config
- application start
- application stop
- application upgrade
- backup
- backup-logs
- clock
- configure
- copy
- debug
- delete
- dir
- exit
- forceout
- halt
- mkdir
- ncs start
- ncs stop
- ncs status
- ncs password ftpuser password
- ncs password root password
- ncs ha authkey
- ncs ha remove
- ncs ha status
- ncs key genkey
- ncs key importcacert
- ncs key importkey
- ncs key listcacerts
- ncs key deletecacert
- ncs key importsignedcert
- ncs cleanup
- ncs db sql
- ncs db reinitdb
- nslookup
- patch install
- patch remove
- ping
- ping6
- reload
- restore
- rmdir
- root
- root_disable
- root_enable
- show
- ssh
- tech dumptcp
- telnet
- terminal length
- terminal session-timeout
- terminal session-welcome
- terminal terminal-type
- traceroute
- undebug
- write
- Cisco Plug and Play Gateway Commands
application install
To install a specific application other than the Prime Infrastructure, use the application install command in EXEC mode. To remove this function, use the application remove command.
Syntax Description
Usage Guidelines
Installs the specified application bundle on the appliance. The application bundle file is pulled from the specified repository.
If you enter the application install or application remove command when another installation or removal operation of an application is in progress, you will see the following warning message:
An existing application install, remove, or upgrade is in progress. Try again shortly.Examples
ncs/admin# application install ncs-appbundle-1.0.2.054.i386.tar.gz myrepository Do you want to save the current configuration ? (yes/no) [yes] ? y Please enter yes or no Do you want to save the current configuration ? (yes/no) [yes] ? yes Generating configuration... Saved the running configuration to startup successfully Initiating Application installation... Extracting NCS database content... Starting NCS database processes... Restarting NCS database processes... Creating NCS M&T session directory... Performing NCS database priming...Application successfully installedncs/admin# application install ncs-appbundle-1.0.2.054.i386.tar.gz myrepository Do you want to save the current configuration ? (yes/no) [yes] ? no Initiating Application installation... Extracting NCS database content... Starting NCS database processes... Restarting NCSdatabase processes... Creating NCS M&T session directory... Performing NCS database priming... Application successfully installedapplication remove
NoteYou are not allowed to run the application remove command from the CLI to remove the Prime Infrastructure application unless you are explicitly instructed to do so for an upgrade.
To remove a specific application other than the Prime Infrastructure, use the application remove command in EXEC mode. To remove this function, use the no form of this command.
Syntax Description
Examples
ncs/admin# application remove ncs Continue with application removal? [y/n] y Application successfully uninstalled ncs/admin#application reset-config
NoteThis command is not currently supported by Prime Infrastructure.
To reset an application configuration to factory defaults, use the application reset-config command in EXEC mode.
Syntax Description
Name of the application to reset its configuration to factory defaults. Up to 255 alphanumeric characters.
Usage Guidelines
You can use the application reset-config command to reset the Prime Infrastructure configuration to factory defaults without reimaging the Prime Infrastructure appliance or VMware.
Examples
ncs/admin# application reset-config ncs Initialize your identity policy database to factory defaults? (y/n): y Reinitializing local policy database to factory default state... Stopping NCS Monitoring & Troubleshooting Log Processor... Stopping NCS Monitoring & Troubleshooting Log Collector... Stopping NCS Monitoring & Troubleshooting Alert Process... Stopping NCS Application Server... Stopping NCS Monitoring & Troubleshooting Session Database... Stopping NCS Database processes... Extracting NCS database content... Starting NCS database processes... Restarting NCS database processes... Creating NCS M&T session directory... Performing NCS database priming... Application successfully reset configurationncs/admin# application reset-config ncs Initialize your identity policy database to factory defaults? (y/n): n Existing policy database will be retained. Application successfully reset configuration ncs/admin#application start
To enable a specific application, use the application start command in EXEC mode. To remove this function, use the no form of this command.
Syntax Description
Usage Guidelines
You cannot use this command to start the Prime Infrastructure application. If you use this command to start the application, you can see that the Prime Infrastructure is already running.
Examples
ncs/admin# application start NCS NCS Database processes is already running, PID: 7585 NCS M&T Session Database is already running, PID: 7851 NCS Application Server process is already running, PID: 7935 NCS M&T Log Collector is already running, PID: 7955 NCS M&T Log Processor is already running, PID: 8005 NCS M&T Alert Processor is already running, PID: 8046 ncs/admin#application stop
To disable a specific application, use the application stop command in EXEC mode. To remove this function, use the no form of this command.
Syntax Description
Examples
ncs/admin# application stop NCS Stopping NCS Monitoring & Troubleshooting Log Processor... Stopping NCS Monitoring & Troubleshooting Log Collector... Stopping NCS Monitoring & Troubleshooting Alert Process... Stopping NCS Application Server... Stopping NCS Monitoring & Troubleshooting Session Database... Stopping NCS Database processes... ncs/admin#application upgrade
To upgrade a specific application bundle, use the application upgrade command in EXEC mode. To remove this function, use the application remove command.
Syntax Description
Application name. Up to 255 alphanumeric characters.
Note Enter the application name as ‘PI’ in uppercase.
Usage Guidelines
Upgrades an application bundle, and preserves any application configuration data.
If you enter the application upgrade command when another application upgrade operation is in progress, you will see the following warning message:
An existing application install, remove, or upgrade is in progress. Try again shortly.
CautionDo not enter the backup or restore commands when the upgrade is in progress. This action might cause the database to be corrupted.
Examples
ncs/admin# application upgrade NCS-appbundle-1.0.2.054.i386.tar.gz myremoterepository Do you want to save the current configuration ? (yes/no) [yes] ? yes Generating configuration... Saved the running configuration to startup successfully Initiating Application Upgrade... ncs/admin#ncs/admin# application upgrade NCS-appbundle-1.0.2.054.i386.tar.gz myremoterepository Do you want to save the current configuration ? (yes/no) [yes] ? no Initiating Application Upgrade... ncs/admin#backup
To perform a backup (including the Prime Infrastructure and Cisco ADE OS data) and place the backup in a repository, use the backup command in EXEC mode. To perform a backup of only the Prime Infrastructure application data without the Cisco ADE OS data, use the application command.
Syntax Description
Usage Guidelines
Performs a backup of the Prime Infrastructure and Cisco ADE OS data and places the backup in a repository.
To perform a backup of only the Prime Infrastructure application data without the Cisco ADE OS data, use the application command.
Examples
ncs/admin# backup mybackup repository myrepository % Creating backup with timestamped filename: mybackup-100805-1222.tar.gpg ncs/admin#ncs/admin# backup mybackup repository myrepository application NCS % Creating backup with timestamped filename: mybackup-100805-1240.tar.gpg ncs/admin#backup-logs
To back up system logs, use the backup-logs command in EXEC mode. To remove this function, use the no form of this command.
Syntax Description
Name of one or more files to back up. Up to 100 alphanumeric characters.
Location where files should be backed up to. Up to 80 alphanumeric characters.
Examples
ncs/admin# backup-logs mybackup repository myrepository % Creating log backup with timestamped filename: mybackup-100805-1754.tar.gz ncs/admin#clock
To set the system clock, use the clock command in EXEC mode. To remove this function, use the no form of this command.
Syntax Description
Current month of the year by name. Up to three alphabetic characters. For example, Jan for January.
Current day (by date) of the month. Value = 0 to 31. Up to two numbers.
Current time in hours (24-hour format), minutes, and seconds.
Usage Guidelines
Sets the system clock. You must restart the Prime Infrastructure server after you reset the clock for the change to take effect.
Examples
ncs/admin# clock set May 5 18:07:20 2010 ncs/admin# show clock Thu May 5 18:07:26 UTC 2010 ncs/admin#configure
To enter configuration mode, use the configure command in EXEC mode. If the replace option is used with this command, copies a remote configuration to the system which overwrites the existing configuration.
Syntax Description
Usage Guidelines
Use this command to enter configuration mode. Note that commands in this mode write to the running configuration file as soon as you enter them (press Enter).
To exit configuration mode and return to EXEC mode, enter end, exit, or pressCtrl-z.
To view the changes that you have made to the configuration, use the show running-config command in EXEC mode.
Examples
ncs/admin# configure Enter configuration commands, one per line. End with CNTL/Z. ncs/admin(config)#ncs/admin# configure terminal Enter configuration commands, one per line. End with CNTL/Z. ncs/admin(config)#copy
Syntax Description
Represents the configuration file used during initialization (startup).
See Table A-5 for protocol keyword options.
Copies all Prime Infrastructure log files from the system to another location. All logs are packaged as ncslogs.tar.gz and transferred to the specified directory on the remote host.
Allows you to copy a single Prime Infrastructure log file and transfer it to the specified directory on the remote host, with its original name.
Name of the Prime Infrastructure log file, as displayed by the show logs command (up to 255 characters).
Copies the Prime Infrastructure management debug logs and Tomcat logs from the system, bundles them as mgmtlogs.tar.gz, and transfers them to the specified directory on the remote host.
Copies the Prime Infrastructure runtime debug logs from the system, bundles them as runtimelogs.tar.gz, and transfers them to the specified directory on the remote host.
Running Configuration
The fundamental function of the copy command allows you to copy a file (such as a system image or configuration file) from one location to another location. The source and destination for the file specified uses the file system, through which you can specify any supported local or remote file location. The file system being used (a local memory source or a remote system) dictates the syntax used in the command.
You can enter on the command line all of the necessary source and destination information and the username and password to use; or, you can enter the copy command and have the server prompt you for any missing information. You can enter up to a maximum of 2048 characters of source and destination URL information on the command line.
The copy command in the copies a configuration (running or startup).
The active configuration stores itself in the RAM. Every configuration command you enter resides in the running configuration. If you reboot your server, you lose the running configuration. If you make changes that you want to save, you must copy the running configuration to a safe location, such as a network server, or save it as the server startup configuration.
You cannot edit a startup configuration directly. All commands that you enter store themselves in the running configuration, which you can copy into the startup configuration.
In other words, when you boot a server, the startup configuration becomes the initial running configuration. As you modify the configuration, the two diverge: the startup configuration remains the same; the running configuration reflects the changes that you have made. If you want to make your changes permanent, you must save the running configuration to the startup configuration using the write memory command. The write memory command makes the current running configuration permanent.
NoteIf you do not save the running configuration, you will lose all your configuration changes during the next reboot of the server. You can also save a copy of the running and startup configurations using the following commands, to recover in case of loss of configuration:
NoteThe copy command is supported only for the local disk and not for a repository.
TipAliases reduce the amount of typing that you need to do. For example, type copy run start (the abbreviated form of the copy running-config startup-config command).
The entire copying process might take several minutes and differs from protocol to protocol and from network to network.
Use the filename relative to the directory for file transfers.
Examples
ncs/admin# copy run start Generating configuration... ncs/admin#ncs/admin# copy running-config startup-config Generating configuration... ncs/admin#ncs/admin# copy start run ncs/admin#ncs/admin# copy startup-config running-config ncs/admin#ncs/admin# copy logs disk:/ Collecting logs... ncs/admin#This command is used to copy the certificate file from pnp to ftp.
ncs/admin# copy server.key /localdisk/tftp copy server.crt /localdisk/tftp copy ncs_server_certificate /localdisk/tftpExamples
This command is used to copy the certificate from ftp tp pnp.
copy tftp://<PI Server IP Address>/server.key disk:/ copy tftp://<PI Server IP Address>/server.crt disk:/ copy tftp://<PI Server IP Address>/ncs_server_certificate.crt disk:/debug
debug{all | application | backup-restore | cdp | config | icmp | copy | locks | logging | snmp | system | transfer | user | utils}
Syntax Description
- all—Enables all application debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- install—Enables application install debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- operation—Enables application operation debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- uninstall—Enables application uninstall debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- all—Enables all debug output for backup-restore. Set level between 0 and 7, with 0 being severe and 7 being all.
- backup—Enables backup debug output for backup-restore. Set level between 0 and 7, with 0 being severe and 7 being all.
- backup-logs—Enables backup-logs debug output for backup-restore. Set level between 0 and 7, with 0 being severe and 7 being all.
- history—Enables history debug output for backup-restore. Set level between 0 and 7, with 0 being severe and 7 being all.
- restore—Enables restore debug output for backup-restore. Set level between 0 and 7, with 0 being severe and 7 being all.
Cisco Discovery Protocol configuration files.
- all—Enables all Cisco Discovery Protocol configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- config—Enables configuration debug output for Cisco Discovery Protocol. Set level between 0 and 7, with 0 being severe and 7 being all.
- infra—Enables infrastructure debug output for Cisco Discovery Protocol. Set level between 0 and 7, with 0 being severe and 7 being all.
- all—Enables all configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- backup—Enables backup configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- clock—Enables clock configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- infra—Enables configuration infrastructure debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- kron—Enables command scheduler configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- network—Enables network configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- repository—Enables repository configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- service—Enables service configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
Internet Control Message Protocol (ICMP) echo response configuration.
all—Enable all debug output for ICMP echo response configuration. Set level between 0 and 7, with 0 being severe and 7 being all.
Copy commands. Set level between 0 and 7, with 0 being severe and 7 being all.
all—Enables all logging configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
all—Enables all SNMP configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- all—Enables all system files debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- id—Enables system ID debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- info—Enables system info debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
- init—Enables system init debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
File transfer. Set level between 0 and 7, with 0 being severe and 7 being all.
Utilities configuration files.
all—Enables all utilities configuration debug output. Set level between 0 and 7, with 0 being severe and 7 being all.
Usage Guidelines
Use the debug command to identify various failures within the Prime Infrastructure server; for example, setup failures or configuration failures.
Examples
ncs/admin# debug all ncs/admin# mkdir disk:/1 ncs/admin# 6 [15347]: utils: vsh_root_stubs.c[2742] [admin]: mkdir operation success ncs/admin# rmdir disk:/1 6 [15351]: utils: vsh_root_stubs.c[2601] [admin]: Invoked Remove Directory disk:/1 command 6 [15351]: utils: vsh_root_stubs.c[2663] [admin]: Remove Directory operation success ncs/admin# ncs/admin# undebug all ncs/admin#delete
To delete a file from the Prime Infrastructure server, use the delete command in EXEC mode. To remove this function, use the no form of this command.
Syntax Description
dir
To list a file from the Prime Infrastructure server, use the dir command in EXEC mode. To remove this function, use the no form of this command.
Syntax Description
Examples
ncs/admin# dir Directory of disk:/ 2034113 Aug 05 2010 19:58:39 ADElogs.tar.gz 4096 Jun 10 2010 02:34:03 activemq-data/ 4096 Aug 04 2010 23:14:53 logs/ 16384 Jun 09 2010 02:59:34 lost+found/ 2996022 Aug 05 2010 19:11:16 mybackup-100805-1910.tar.gz 4096 Aug 04 2010 23:15:20 target/ 4096 Aug 05 2010 12:25:55 temp/ Usage for disk: filesystem 8076189696 bytes total used 6371618816 bytes free 15234142208 bytes available ncs/admin#ncs/admin# dir disk:/logs 0 Aug 05 2010 11:53:52 usermgmt.log Usage for disk: filesystem 8076189696 bytes total used 6371618816 bytes free 15234142208 bytes available ncs/admin#ncs/admin# dir recursive Directory of disk:/ 2034113 Aug 05 2010 19:58:39 ADElogs.tar.gz 2996022 Aug 05 2010 19:11:16 mybackup-100805-1910.tar.gz 4096 Aug 04 2010 23:14:53 logs/ 4096 Aug 05 2010 12:25:55 temp/ 4096 Jun 10 2010 02:34:03 activemq-data/ 4096 Aug 04 2010 23:15:20 target/ 16384 Jun 09 2010 02:59:34 lost+found/ Directory of disk:/logs 0 Aug 05 2010 11:53:52 usermgmt.log Directory of disk:/temp 281 Aug 05 2010 19:12:45 RoleBundles.xml 6631 Aug 05 2010 19:12:34 PipDetails.xml 69 Aug 05 2010 19:12:45 GroupRoles.xml 231 Aug 05 2010 19:12:34 ApplicationGroupTypes.xml 544145 Aug 05 2010 19:12:35 ResourceTypes.xml 45231 Aug 05 2010 19:12:45 UserTypes.xml 715 Aug 05 2010 19:12:34 ApplicationGroups.xml 261 Aug 05 2010 19:12:34 ApplicationTypes.xml 1010 Aug 05 2010 19:12:34 Pdps.xml 1043657 Aug 05 2010 19:12:44 Groups.xml 281003 Aug 05 2010 19:12:38 Resources.xml 69 Aug 05 2010 19:12:45 GroupUsers.xml 2662 Aug 05 2010 19:12:44 RoleTypes.xml 79 Aug 05 2010 19:12:34 UserStores.xml 4032 Aug 05 2010 19:12:38 GroupTypes.xml 1043 Aug 05 2010 19:12:34 Organization.xml 58377 Aug 05 2010 19:12:46 UserRoles.xml 300 Aug 05 2010 19:12:45 Contexts.xml 958 Aug 05 2010 19:12:34 Applications.xml 28010 Aug 05 2010 19:12:45 Roles.xml 122761 Aug 05 2010 19:12:45 Users.xml Directory of disk:/activemq-data 4096 Jun 10 2010 02:34:03 localhost/ Directory of disk:/activemq-data/localhost 0 Jun 10 2010 02:34:03 lock 4096 Jun 10 2010 02:34:03 journal/ 4096 Jun 10 2010 02:34:03 kr-store/ 4096 Jun 10 2010 02:34:03 tmp_storage/ Directory of disk:/activemq-data/localhost/journal 33030144 Aug 06 2010 03:40:26 data-1 2088 Aug 06 2010 03:40:26 data-control Directory of disk:/activemq-data/localhost/kr-store 4096 Aug 06 2010 03:40:27 data/ 4096 Aug 06 2010 03:40:26 state/ Directory of disk:/activemq-data/localhost/kr-store/data 102 Aug 06 2010 03:40:27 index-container-roots 0 Aug 06 2010 03:40:27 lock Directory of disk:/activemq-data/localhost/kr-store/state 3073 Aug 06 2010 03:40:26 hash-index-store-state_state 51 Jul 20 2010 21:33:33 index-transactions-state 204 Aug 06 2010 03:40:26 index-store-state 306 Jun 10 2010 02:34:03 index-kaha 290 Jun 10 2010 02:34:03 data-kaha-1 71673 Aug 06 2010 03:40:26 data-store-state-1 0 Jun 10 2010 02:34:03 lock Directory of disk:/activemq-data/localhost/tmp_storage No files in directory Directory of disk:/target 4096 Aug 04 2010 23:15:20 logs/ Directory of disk:/target/logs 0 Aug 04 2010 23:15:20 ProfilerPDP.log 2208 Aug 05 2010 11:54:26 ProfilerSensor.log Directory of disk:/lost+found No files in directory Usage for disk: filesystem 8076189696 bytes total used 6371618816 bytes free 15234142208 bytes available ncs/admin#exit
To close an active terminal session by logging out of the Prime Infrastructure server or to move up one mode level from configuration mode, use the exit command in EXEC mode.
forceout
halt
Usage Guidelines
Before you enter the halt command, ensure that the Prime Infrastructure is not performing any backup, restore, installation, upgrade, or remove operation. If you enter the halt command while the Prime Infrastructure is performing any of these operations, you will get one of the following warning messages:
WARNING: A backup or restore is currently in progress! Continue with halt? WARNING: An install/upgrade/remove is currently in progress! Continue with halt?If you get any of these warnings, enter YEs to halt the operation, or enter NO to cancel the halt.
If no processes are running when you use the halt command or if you enter Yes in response to the warning message displayed, the Prime Infrastructure asks you to respond to the following option:
Do you want to save the current configuration ?Enter YES to save the existing Prime Infrastructure configuration. The Prime Infrastructure displays the following message:
Saved the running configuration to startup successfullymkdir
Syntax Description
Usage Guidelines
Use disk:/path with the directory name; otherwise, an error appears that indicates that the disk:/path must be included.
Examples
ncs/admin# mkdir disk:/test ncs/admin# dir Directory of disk:/ 4096 May 06 2010 13:34:49 activemq-data/ 4096 May 06 2010 13:40:59 logs/ 16384 Mar 01 2010 16:07:27 lost+found/ 4096 May 06 2010 13:42:53 target/ 4096 May 07 2010 12:26:04 test/ Usage for disk: filesystem 181067776 bytes total used 19084521472 bytes free 20314165248 bytes available ncs/admin#ncs start
Syntax Description
Examples
This example shows how to start the server:
> ncs start verbose Starting Network Control System... Starting Health Monitor Starting Health Monitor as a primary Checking for Port 8082 availability... OK Starting Health Montior Web Server... Health Monitor Web Server Started. Starting Health Monitor Server... Health Monitor Server Started. Starting Service Name: Reporting Starting dependency service: NMS Server Starting dependency service: Matlab Starting remoting: Matlab Server Checking for Port 20555 availability... OK Remoting Service Matlab Server application root: /opt/CSCOncs Starting Remoting Service Web Server Matlab Server... Remoting Service Web Server Matlab Server Started. Starting Remoting Service Matlab Server... Remoting 'Matlab Server' started successfully. Starting dependency service: Ftp Starting remoting: Ftp Server Checking for Port 20558 availability... OK Starting up FTP server Started FTP FTP Server started Remoting Service Ftp Server application root: /opt/CSCOncs Starting Remoting Service Web Server Ftp Server... Remoting Service Web Server Ftp Server Started. Starting Remoting Service Ftp Server... Remoting 'Ftp Server' started successfully. Starting dependency service: Tftp Starting remoting: Tftp Server Checking for Port 20559 availability... OK Starting up TFTP server... TFTP Server started. Remoting Service Tftp Server application root: /opt/CSCOncs Starting Remoting Service Web Server Tftp Server... Remoting Service Web Server Tftp Server Started. Starting Remoting Service Tftp Server... Remoting 'Tftp Server' started successfully. Starting NMS Server Checking for running servers. Checking if DECAP is running. 00:00 DECAP is not running. 00:00 Check complete. No servers running. 00:10 DECAP setup complete. Starting Server ... Reporting started successfully Starting Service Name: Ftp Ftp is already running. Starting Service Name: Database 00:40 Server started. 00:40 DONE Done Database is already running. Starting Service Name: Tftp Tftp is already running. Starting Service Name: Matlab Matlab is already running. Starting Service Name: NMS Server NMS Server is already running. Network Control System started successfully.ncs stop
To stop the Prime Infrastructure server, use the ncs stop command in EXEC mode. To see the detailed messages, use the ncs stop verbose command.
Syntax Description
Examples
This example shows how to stop the Prime Infrastructure server:
> ncs stop verbose Stopping Network Control System... Stopping Network Control System server Stopping Service Name: Reporting Stopping Reporting Reporting successfully shutdown. Stopping Service Name: Ftp Stopping NMS Server Stopping Reporting Server(XMP) ..DONE NMS Server successfully shutdown. Stopping remoting: Ftp Server Stopping FTP server... Stopped FTP server. Stopping Remoting Web Server Ftp Server... Remoting Web Server Ftp Server stopped. Remoting 'Ftp Server' stopped successfully. Stopping Service Name: Database Shutting down database server ... Stopping XMP ....DONE Stopping Service Name: Tftp Stopping remoting: Tftp Server Stopping TFTP server... Stopped TFTP server. Stopping Remoting Web Server Tftp Server... Remoting Web Server Tftp Server stopped. Remoting 'Tftp Server' stopped successfully. Stopping Service Name: Matlab Stopping remoting: Matlab Server Stopping Remoting Web Server Matlab Server... Remoting Web Server Matlab Server stopped. Warning: latest version of matlab app-defaults file not found. Contact your system administrator to have this file installed. Remoting 'Matlab Server' stopped successfully. Stopping Service Name: NMS Server NMS Server is not running. Stopping Tomcat... Tomcat Stopped. Network Control System successfully shutdown.ncs status
ncs password ftpuser password
To change the FTP username and password, use the ncs password ftpuser password command in EXEC mode.
Syntax Description
The modified password. The password cannot contain 'cisco' or 'ocsic', or any variant obtained by changing the capitalization of letters therein or by substituting '1', '|', or '!' for i, '0' for 'o', or '$' for 's'.
ncs password root password
Syntax Description
The modified password. The password cannot contain 'cisco' or 'ocsic', or any variant obtained by changing the capitalization of letters therein or by substituting '1', '|', or '!' for i, '0' for 'o', or '$' for 's'.
Examples
Prime InfrastructureThis example shows how to migrate archived files to server:
> ncs password root password Private123 Loading USER - root Validating new password.. Resetting password .. Resetting password COMPLETED. EXECUTION STATUS : Successncs ha authkey
To enter the authentication key for high availability (HA), use the ncs ha authkey command in EXEC mode.
Syntax Description
Examples
This example shows how to set up the authorization key for high availability:
ncs ha authkey cisco123ncs ha remove
To remove the high availability configuration settings from Prime Infrastructure, use the ncs ha remove command in EXEC mode.
Usage Guidelines
The ncs ha remove command removes the high availability configuration settings from Prime Infrastructure. If you enter this command, you will see the following confirmation message:
High availability configuration will be removed. Do you wish to continue? (Y/N)ncs ha status
To display the current status of high availability (HA), use the ncs ha status command in EXEC mode.
Usage Guidelines
Displays the current status of HA.
If you enter the ncs ha status command when HA is not configured, you will see the following response:
[State] Stand Alonencs key genkey
To generate a new RSA key and self-signed certificate, use the ncs key genkey command. You can use this command in the following ways:
Syntax Description
genkey
Generates a new RSA key and self-signed certificate. You can use the following options with this command:
-csr: Generate Certificate Signing Request(CSR) file
-newdn: Generate new RSA key and self-signed certificate with domain information
<cr>: Carriage return.
Generates a new RSA key and self-signed cert with domain information. You can use the following options with this command:
-csr: Generate Certificate Signing Request(CSR) file
<cr>: Carriage return.
Generates new CSR certificate file. You can use the following option with this command:
<WORD>: Type in certificate file name (Max Size - 80)
Repository command. This option is available when you use the -csr option.
Location where the files should be backed up to. Up to 80 alphanumeric characters.
Examples
This example shows how to generate new rsa key and certificate files in the Prime Infrastructure server:
>ncs key genkey -newdn -csr csrfile.cert repository ncs-sftp-repo Generating RSA key INFO: no staging url defined, using local space. rval:2Related Commands
Description
Applies a CA certificate to the trust store in Prime Infrastructure.
Lists all of the CA certificates that exist in the Prime Infrastructure trust store.
Deletes a CA certificates that exist in the Prime Infrastructure trust store.
Applies an RSA key and signed certificate to Prime Infrastructure.
Note
After entering this command, enter the ncs stop and ncs start command to restart the Prime Infrastructure server to make changes take effect.
ncs key importcacert
To apply a CA certificate to a trust store in Prime Infrastructure, use the ncs key importcacert command in the EXEC mode.
Syntax Description
repository
Repository command.
The repository name configured in Prime Infrastructure where the ca-cert-filename is hosted.
Examples
This example shows how to apply the CA certificate file to a trust store in the Prime Infrastructure server:
> ncs key importcacert alias1 cacertfile repository ncs-sftp-repo
NoteAfter applying this command, enter the ncs stop and ncs start command to restart the Prime Infrastructure server to make the changes take effect.
ncs key importkey
To apply an RSA key and signed certificate to the Prime Infrastructure, use the ncs key importkey command in EXEC mode.
Syntax Description
Repository command
The repository name configured in the Prime Infrastructure where the key-file and cert-file is hosted.
Examples
This example shows how to apply the new RSA key and certificate files to the server.
> ncs key importkey keyfile certfile repository ncs-sftp-repo
NoteAfter applying this command, enter the ncs stop and ncs start command to restart the server to make the changes take effect.
Related Commands
Description
Lists all of the CA certificates that exist in the Prime Infratsructure trust store.
Deletes a CA certificates that exist in the Prime Infratsructure trust store.
Applies an RSA key and signed certificate to Prime Infratsructure.
Applies an CA certificate to trust store in the Prime Infratsructure.
ncs key listcacerts
To list all of the CA certificates that exist in the Prime Infrastructure trust store, use the ncs key listcacerts command EXEC mode.
Examples
This example shows how to list all of the CA certificates that exist in the Prime Infrastructure trust store:
> ncs key listcacerts Certificate utnuserfirsthardwareca from CN=UTN-USERFirst-Hardware, OU=http://www.example.com, O=The USERTRUST Network, L=Salt Lake City, ST=UT, C=US Certificate gtecybertrust5ca from CN=GTE CyberTrust Root 5, OU="GTE CyberTrust Solutions, Inc.", O=GTE Corporation, C=US Certificate equifaxsecureebusinessca1 from CN=Equifax Secure eBusiness CA-1, O=Equifax Secure Inc., C=US Certificate thawtepersonalfreemailca from EMAILADDRESS=email@example.com, CN=Thawte Personal Freemail CA, OU=Certification Services Division, O=Thawte Consulting, L=Cape Town, ST=Western Cape, C=ZA Certificate addtrustclass1ca from CN=AddTrust Class 1 CA Root, OU=AddTrust TTP Network, O=AddTrust AB, C=SE Certificate aolrootca1 from CN=America Online Root Certification Authority 1, O=America Online Inc., C=US Certificate geotrustuniversalca from CN=GeoTrust Universal CA, O=GeoTrust Inc., C=US Certificate digicertglobalrootca from CN=DigiCert Global Root CA, OU=www.example.com, O=DigiCert Inc, C=US Certificate certumtrustednetworkca from CN=Certum Trusted Network CA, OU=Certum Certification Authority, O=Unizeto Technologies S.A., C=PL Certificate swisssignsilverg2ca from CN=SwissSign Silver CA - G2, O=SwissSign AG, C=CHRelated Commands
ncs key deletecacert
To delete CA certificates that exist in Prime Infrastructure trust store, use the ncs key deletecacert command in the EXEC mode.
Syntax Description
The short or alias name of the CA certificate which needs to be deleted from the Prime Infrastructure trust store.
Examples
This example shows how to delete CA certificates that exist in the Prime Infrastructure trust store:
> ncs key deletecacert certumtrustednetworkca Deleting certificate from trust storeRelated Commands
ncs key importsignedcert
Syntax Description
repository
Repository command
The repository name configured in Prime Infrastructure where the key-file and cert-file is hosted.
Examples
This example shows how to apply signed certificate files to the Prime Infrastructure server:
> ncs key importsingedcert signed-certfile repository ncs-sftp-repo
NoteAfter applying this command, enter the ncs stop and the ncs start command to restart the Prime Infrastructure server to make changes take effect.
Related Commands
Description
Applies an RSA key and signed certificate to Prime Infrastructure.
Deletes CA certificates that exist in the Prime Infrastructure trust store.
Lists all of the CA certificates that exist in the Prime Infrastructure trust store.
Applies a CA certificate to the trust store in Prime Infrastructure.
ncs db sql
ncs db reinitdb
To reinitialize the Prime Infratsructure database, use the ncs db reinitdb command in EXEC mode. This command removes all data present in the database.
nslookup
To look up the hostname of a remote system on the Prime Infrastructure server, use the nslookup command in EXEC mode.
Syntax Description
Examples
ncs/admin# nslookup 209.165.200.225 Trying "209.165.200.225.in-addr.arpa" Received 127 bytes from 172.16.168.183#53 in 1 ms Trying "209.165.200.225.in-addr.arpa" Host 209.165.200.225.in-addr.arpa. not found: 3(NXDOMAIN) Received 127 bytes from 172.16.168.183#53 in 1 ms ncs/admin#ncs/admin# nslookup 209.165.200.225 Trying "225.200.165.209.in-addr.arpa" ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 65283 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 2, ADDITIONAL: 0 ;; QUESTION SECTION: ;225.200.165.209.in-addr.arpa. IN PTR ;; ANSWER SECTION: 225.200.165.209.in-addr.arpa. 86400 IN PTR 209-165-200-225.got.net. ;; AUTHORITY SECTION: 192.168.209.in-addr.arpa. 86400 IN NS ns1.got.net. 192.168.209.in-addr.arpa. 86400 IN NS ns2.got.net. Received 119 bytes from 172.16.168.183#53 in 28 ms ncs/admin#patch install
Syntax Description
Usage Guidelines
The patch install command installs a patch bundle of the application only on a specific node where you run the patch install command from the CLI.
If you attempt to install a patch that is an older version of the existing patch, then you receive the following error message:
% Patch to be installed is an older version than currently installed version.
NoteIn a Prime Infrastructure distributed deployment environment, install the patch bundle of the application from the primary Policy Administration Point (PAP) node in the Prime Infrastructure Administration user interface so that the patch bundle automatically gets installed on all of the secondary nodes.
Examples
ncs/admin# patch install ncs-appbundle-1.0.2.054-3.i386.tar.gz myrepository Do you want to save the current configuration ? (yes/no) [yes] ? yes Generating configuration... Saved the running configuration to startup successfully Initiating Application Patch installation... Patch successfully installed ncs/admin#ncs/admin# patch install ncs-appbundle-1.0.2.054-3.i386.tar.gz myrepository Do you want to save the current configuration ? (yes/no) [yes] ? no Initiating Application Patch installation... Patch successfully installed ncs/admin#ncs/admin# patch install ncs-appbundle-1.0.2.054-2.i386.tar.gz disk Do you want to save the current configuration ? (yes/no) [yes] ? yes Generating configuration... Saved the running configuration to startup successfully Initiating Application Patch installation... % Patch to be installed is an older version than currently installed version. ncs/admin#patch remove
To remove a specific patch bundle version of the application, use the patch remove command in EXEC mode.
Syntax Description
The name of the application for which the patch is to be removed. Up to 255 alphanumeric characters.
The patch version number to be removed. Up to 255 alphanumeric characters.
Usage Guidelines
Removes a specific patch bundle of the application.
If you attempt to remove a patch that is not installed, then you receive the following error message:
NoteIn a Prime Infrastructure distributed deployment environment, remove the patch bundle of the application from the primary Policy Administration Point (PAP) node in the Prime Infrastructure Administration user interface so that the patch bundle automatically gets uninstalled from all of the secondary nodes.
% Patch is not installedExamples
ncs/admin# patch remove ncs 3 Continue with application patch uninstall? [y/n] y Application patch successfully uninstalled ncs/admin#ncs/admin# patch remove ncs 3 Continue with application patch uninstall? [y/n] y % Patch is not installed ncs/admin#ping
To diagnose the basic IPv4 network connectivity to a remote system, use the ping command in EXEC mode.
Syntax Description
IP address of the system to ping. Up to 32 alphanumeric characters.
Hostname of the system to ping. Up to 32 alphanumeric characters.
Specifies the value as 1 to prohibit packet fragmentation, or 2 to fragment the packets locally, or 3 to not set df.
Specifies the size of the ping packet; the value can be between 0 and 65507.
Specifies the number of ping echo requests; the value can be between 1 and 10.
Usage Guidelines
The ping command sends an echo request packet to an address, then awaits a reply. The ping output can help you evaluate path-to-host reliability, delays over the path, and whether you can reach a host.
Examples
ncs/admin# ping 172.16.0.1 df 2 packetsize 10 pingcount 2 PING 172.16.0.1 (172.16.0.1) 10(38) bytes of data. 18 bytes from 172.16.0.1: icmp_seq=0 ttl=40 time=306 ms 18 bytes from 172.16.0.1: icmp_seq=1 ttl=40 time=300 ms --- 172.16.0.1 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 300.302/303.557/306.812/3.255 ms, pipe 2 ncs/admin#ping6
To diagnose the basic IPv6 network connectivity to a remote system, use the ping6 command in EXEC mode.
Syntax Description
IP address of the system to ping. Up to 64 alphanumeric characters.
Hostname of the system to ping. Up to 64 alphanumeric characters.
Specifies the size of the ping packet; the value can be between 0 and 65507.
Specifies the number of ping echo requests; the value can be between 1 and 10.
Usage Guidelines
The IPv6 ping6 command sends an echo request packet to an address, then awaits a reply. The ping output can help you evaluate path-to-host reliability, delays over the path, and whether you can reach a host.
The IPv6 ping6 command is similar to the existing IPv4 ping command that does not support the IPv4 ping fragmentation (df in IPv4) options, but allows an optional specification of an interface. The interface option is primarily useful for pinning with link-local addresses that are interface-specific. The packetsize and pingcount options work identically the same as they do with the IPv4 command.
Examples
ncs/admin# ping6 3ffe:302:11:2:20c:29ff:feaf:da05 PING 3ffe:302:11:2:20c:29ff:feaf:da05(3ffe:302:11:2:20c:29ff:feaf:da05) from 3ffe:302:11:2:20c:29ff:feaf:da05 eth0: 56 data bytes 64 bytes from 3ffe:302:11:2:20c:29ff:feaf:da05: icmp_seq=0 ttl=64 time=0.599 ms 64 bytes from 3ffe:302:11:2:20c:29ff:feaf:da05: icmp_seq=1 ttl=64 time=0.150 ms 64 bytes from 3ffe:302:11:2:20c:29ff:feaf:da05: icmp_seq=2 ttl=64 time=0.070 ms 64 bytes from 3ffe:302:11:2:20c:29ff:feaf:da05: icmp_seq=3 ttl=64 time=0.065 ms --- 3ffe:302:11:2:20c:29ff:feaf:da05 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3118ms rtt min/avg/max/mdev = 0.065/0.221/0.599/0.220 ms, pipe 2 ncs/admin#ncs/admin# ping6 3ffe:302:11:2:20c:29ff:feaf:da05 GigabitEthernet 0 packetsize 10 pingcount 2 PING 3ffe:302:11:2:20c:29ff:feaf:da05(3ffe:302:11:2:20c:29ff:feaf:da05) from 3ffe:302:11:2:20c:29ff:feaf:da05 eth0: 10 data bytes 18 bytes from 3ffe:302:11:2:20c:29ff:feaf:da05: icmp_seq=0 ttl=64 time=0.073 ms 18 bytes from 3ffe:302:11:2:20c:29ff:feaf:da05: icmp_seq=1 ttl=64 time=0.073 ms --- 3ffe:302:11:2:20c:29ff:feaf:da05 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1040ms rtt min/avg/max/mdev = 0.073/0.073/0.073/0.000 ms, pipe 2 ncs/admin#reload
Usage Guidelines
The reload command reboots the system. Use the reload command after you enter configuration information into a file and save the running-configuration to the persistent startup-configuration on the CLI and save any settings in the web Administration user interface session.
Before you enter the reload command, ensure that the Prime Infrastructure is not performing any backup, restore, installation, upgrade, or remove operation. If the Prime Infrastructure performs any of these operations and you enter the reload command, you will notice any of the following warning messages:
WARNING: A backup or restore is currently in progress! Continue with reload? WARNING: An install/upgrade/remove is currently in progress! Continue with reload?If you get any of these warnings, enter YES to halt the operation, or enter NO to cancel the halt.
If no processes are running when you use the reload command or you enter YES in response to the warning message displayed, the Prime Infrastructure asks you to respond to the following option:
Do you want to save the current configuration ?Enter YES to save the existing Prime Infrastructure configuration. The Prime Infrastructure displays the following message:
Saved the running configuration to startup successfullyExamples
ncs/admin# reload Do you want to save the current configuration ? (yes/no) [yes] ? yes Generating configuration... Saved the running configuration to startup successfully Continue with reboot? [y/n] y Broadcast message from root (pts/0) (Fri Aug 7 13:26:46 2010): The system is going down for reboot NOW! ncs/admin#restore
To perform a restore of a previous backup, use the restore command in EXEC mode.
Use the following command to restore data related to the Prime Infrastructure application and Cisco ADE OS:
restore filename repository repository-name
Use the following command to restore data related only to the Prime Infrastructure application:
Syntax Description
Name of the backed-up file that resides in the repository. Up to 120 alphanumeric characters.
Note You must add the .tar.gpg extension after the filename (for example, myfile.tar.gpg).
The name of the application data to be restored. Up to 255 alphanumeric characters.
Note Enter the application name as ‘PI’ in upper case.
Usage Guidelines
A restore operation restores data related to the Prime Infrastructure as well as the Cisco ADE OS. To perform a restore of a previous backup of the application data of the Prime Infrastructure only, add the application command to the restore command in EXEC mode. To remove this function, use the no form of this command.
When you use these two commands in the Prime Infrastructure, the Prime Infrastructure server restarts automatically.
Examples
ncs/admin# restore mybackup-100818-1502.tar.gpg repository myrepository Restore may require a reboot to successfully complete. Continue? (yes/no) [yes] ? yes Stopping NCS Monitoring & Troubleshooting Log Processor... Stopping NCS Monitoring & Troubleshooting Log Collector... Stopping NCS Monitoring & Troubleshooting Alert Process... Stopping NCS Monitoring & Troubleshooting Session Database... Stopping NCS Application Server... Stopping NCS Database processes... Starting NCS Database processes... Starting NCS Application Server... Starting NCS Monitoring & Troubleshooting Session Database... Starting NCS Monitoring & Troubleshooting Log Collector... Starting NCS Monitoring & Troubleshooting Log Processor... Starting NCS Monitoring & Troubleshooting Alert Process... Note: NCS Processes are initializing. Use 'show application status NCS' CLI to verify all processes are in running state. Broadcast message from root (pts/0) (Wed Aug 18 15:34:58 2010): The system is going down for reboot NOW! ncs/admin# Last login: Wed Aug 18 14:00:27 2010 from 10.77.137.60 ncs/admin# show application status NCS NCS Database listener is running, PID: 3024 NCS Database is running, number of processes: 34 NCS Application Server is still initializing. NCS M&T Session Database is running, PID: 2793 NCS M&T Log Collector is running, PID: 3336 NCS M&T Log Processor is running, PID: 3379 NCS M&T Alert Process is running, PID: 3442 ncs/admin#rmdir
Syntax Description
Examples
ncs/admin# mkdir disk:/test ncs/admin# dir Directory of disk:/ 4096 May 06 2010 13:34:49 activemq-data/ 4096 May 06 2010 13:40:59 logs/ 16384 Mar 01 2010 16:07:27 lost+found/ 4096 May 06 2010 13:42:53 target/ 4096 May 07 2010 12:26:04 test/ Usage for disk: filesystem 181067776 bytes total used 19084521472 bytes free 20314165248 bytes available ncs/admin# ncs/admin# rmdir disk:/test ncs/admin# dir Directory of disk:/ 4096 May 06 2010 13:34:49 activemq-data/ 4096 May 06 2010 13:40:59 logs/ 16384 Mar 01 2010 16:07:27 lost+found/ 4096 May 06 2010 13:42:53 target/ Usage for disk: filesystem 181063680 bytes total used 19084525568 bytes free 20314165248 bytes available ncs/admin#root
To execute the root shell, use the root command in EXEC mode.
NoteFor developer use only, not for end users.
Usage Guidelines
Requires installation of the root_enable application or patch. The root command prompts for the password used with root_enable and puts you in a bash shell with root privileges.
There are no defaults for the password.
If the password is already set, the root_enable command generates the following error message:
% Error : root patch password already setIf the password is not set, the root command generates the following error message:
% Error : root patch password not set.
NoteThis command and the root_enable command can only be used on the Prime Infrastructure locally hard-wired console port via Telnet. If you try to access this port over a LAN via SSH or Telnet, the commands are disallowed and the following message appears: % Error : root patch only available on a console port.
root_disable
To disable the root user restoring admin shell access, use the root_disable command in the EXEC mode.
NoteFor developer use only, not for end users.
Usage Guidelines
Noteroot_enable
To activate the root command, use the root_enable command in the EXEC mode.
NoteFor developer use only, not for end users.
Usage Guidelines
Requires installation of the root_enable application or patch. The root command prompts for the password used with root_enable and puts you in a bash shell with root privileges.
There are no defaults for the password.
If the password is already set, the root_enable command generates the following error message:
% Error : root patch password already setIf the password is not set, the root command generates the following error message:
% Error : root patch password not set
Noteshow
To show the running system information, use the show command in EXEC mode. The show commands are used to display the Prime Infrastructure settings and are among the most useful commands.
The commands in Table A-6 require the show command to be followed by a keyword; for example, show application status. Some show commands require an argument or variable after the keyword to function; for example, show application version.
For detailed information on all of the Prime Infrastructure show commands, see show Commands, page A-61.
show keyword
Syntax Description
Table 5 Summary of show Commands Command(1)
Description
application
(requires keyword)(2)
Displays information about the installed application; for example, status or version.
backup
(requires keyword)
Displays information about the backup.
cdp
(requires keyword)
Displays information about the enabled Cisco Discovery Protocol interfaces.
clock
Displays the day, date, time, time zone, and year of the system clock.
cpu
Displays CPU information.
disks
Displays file-system information of the disks.
interface
Displays statistics for all of the interfaces configured on the Cisco ADE OS.
logging
(requires keyword)
Displays system logging information.
logins
(requires keyword)
Displays login history.
memory
Displays memory usage by all running processes.
ntp
Displays the status of the Network Time Protocol (NTP).
ports
Displays all of the processes listening on the active ports.
process
Displays information about the active processes of the Prime Infrastructure server.
repository
(requires keyword)
Displays the file contents of a specific repository.
restore
(requires keyword)
Displays restore history on the Prime Infrastructure server.
running-config
Displays the contents of the currently running configuration file on the Prime Infrastructure server.
startup-config
Displays the contents of the startup configuration on the Prime Infrastructure server.
tech-support
Displays system and configuration information that you can provide to the TAC when you report a problem.
terminal
Displays information about the terminal configuration parameter settings for the current terminal line.
timezone
Displays the time zone of the Prime Infrastructure server.
timezones
Displays all of the time zones available for use on the Prime Infrastructure server.
udi
Displays information about the unique device identifier (UDI) of the Prime Infrastructure.
uptime
Displays how long the system you are logged in to has been up and running.
users
Displays information for currently logged in users.
version
Displays information about the installed application version.
12 1 (1) The commands in this table require that the show command precedes a keyword; for example, show application.2 (2) Some show commands require an argument or variable after the keyword to function; for example, show application version. This show command displays the version of the application installed on the system (see show application, page A-61 ).ssh
To start an encrypted session with a remote system, use the ssh command in EXEC mode.
NoteAn Admin or Operator (user) can use this command (see Table 1-1).
Syntax Description
IP address of the remote system. Up to 64 alphanumeric characters.
Hostname of the remote system. Up to 64 alphanumeric characters.
(Optional) Indicates the port number of the remote host. From 0 to 65,535. Default 22.
IPv4 address or hostname of a remote system. Up to 64 alphanumeric characters.
Usage Guidelines
The ssh command enables a system to make a secure, encrypted connection to another remote system or server. This connection provides functionality similar to that of an outbound Telnet connection except that the connection is encrypted. With authentication and encryption, the SSH client allows for secure communication over an insecure network.
tech dumptcp
To dump a Transmission Control Protocol (TCP) package to the console, use the tech dumptcp command in EXEC mode.
Syntax Description
Examples
ncs/admin# tech dumptcp 0 140816:141088(272) ack 1921 win 14144 08:26:12.034630 IP NCS.cisco.com.ssh > dhcp-64-102-82-153.cisco.com.2221: P 141088:141248(160) ack 1921 win 14144 08:26:12.034635 IP dhcp-64-102-82-153.cisco.com.2221 > NCS.cisco.com.ssh: . ack 139632 win 64656 08:26:12.034677 IP NCS.cisco.com.ssh > dhcp-64-102-82-153.cisco.com.2221: P 141248:141520(272) ack 1921 win 14144 08:26:12.034713 IP NCS.cisco.com.ssh > dhcp-64-102-82-153.cisco.com.2221: P 141520:141680(160) ack 1921 win 14144 08:26:12.034754 IP NCS.cisco.com.ssh > dhcp-64-102-82-153.cisco.com.2221: P 141680:141952(272) ack 1921 win 14144 08:26:12.034756 IP dhcp-64-102-82-153.cisco.com.2221 > NCS.cisco.com.ssh: . ack 140064 win 65520 08:26:12.034796 IP NCS.cisco.com.ssh > dhcp-64-102-82-153.cisco.com.2221: P 141952:142112(160) ack 1921 win 14144 1000 packets captured 1000 packets received by filter 0 packets dropped by kernel ncs/admin#telnet
terminal length
To set the number of lines on the current terminal screen for the current session, use the terminal length command in EXEC mode.
Syntax Description
Number of lines on the screen. Contains between 0 to 511 lines, inclusive. A value of zero (0) disables pausing between screens of output.
terminal session-timeout
To set the inactivity timeout for all sessions, use the terminal session-timeout command in EXEC mode.
Syntax Description
Sets the number of minutes for the inactivity timeout. From 0 to 525,600. Zero (0) disables the timeout.
Usage Guidelines
Setting the terminal session-timeout command to zero (0) results in no timeout being set.
terminal session-welcome
terminal terminal-type
To specify the type of terminal connected to the current line for the current session, use the terminal terminal-type command in EXEC mode.
Syntax Description
traceroute
undebug
undebug {all | application | backup-restore | cdp | config | copy | icmp | locks | logging | snmp | system | transfer | user | utils}
Syntax Description
- all—Disables all configuration debug output.
- backup—Disables backup configuration debug output.
- clock—Disables clock configuration debug output.
- infra—Disables configuration infrastructure debug output.
- kron—Disables command scheduler configuration debug output.
- network—Disables network configuration debug output.
- repository—Disables repository configuration debug output.
- service—Disables service configuration debug output.
ICMP echo response configuration.
all—Disable all debug output for ICMP echo response configuration. Set level between 0 and 7, with 0 being severe and 7 being all.
write
To copy, display, or erase Prime Infrastructure server configurations, use the write command with the appropriate argument in EXEC mode.
Syntax Description
Examples
The following is an example of the write command with the memory keyword:
ncs/admin# write memory Generating configuration... ncs/admin#The following is an example of the write command with the terminal keyword:
ncs/admin# write terminal Generating configuration... ! hostname ncs ! ip domain-name cisco.com ! interface GigabitEthernet 0 ip address 10.201.2.121 255.255.255.0 ipv6 address autoconfig ! interface GigabitEthernet 1 shutdown ! interface GigabitEthernet 2 shutdown ! interface GigabitEthernet 3 shutdown ! ip name-server 172.16.226.120 ! ip default-gateway 10.201.2.1 ! clock timezone UTC ! ntp server clock.cisco.com ! username admin password hash $1$6yQQaFXM$UBgbp7ggD1bG3kpExywwZ0 role admin ! service sshd ! repository myrepository url disk: user admin password hash 2b50ca94445f240f491e077b5f49fa0375942f38 ! password-policy lower-case-required upper-case-required digit-required no-username disable-cisco-passwords min-password-length 6 ! logging localhost logging loglevel 6 ! cdp timer 60 cdp holdtime 180 cdp run GigabitEthernet 0 ! icmp echo on ! ncs/admin#Cisco Plug and Play Gateway Commands
- Prime Infrastructure Integrated Server Commands
- Prime Infrastructure PnP Gateway Standalone Server Command
Prime Infrastructure Integrated Server Commands
ncs pnp-gateway
To enable or disable the local Cisco Plug and Play Gateway on the Prime Infrastructure Integrated Server and modify or view the properties of the software image on the Cisco Plug and Play Gateway, use the ncs pnp-gateway command in privileged EXEC mode.
Syntax Description
enable Enables the Cisco Plug and Play Gateway.
disable Disables the Cisco Plug and Play Gateway.
modify Enables the modification of the Cisco Plug and Play Gateway image's properties. The properties that can be modified are: activation timeout value, distribution timeout value, and transfer timeout value.
property Enables viewing of the properties pertaining to the software image on the Cisco Plug and Play Gateway.
Command History
Examples
The following is sample output from the ncs pnp-gateway command:
admin# ncs pnp-gateway? disable PNP Gateway Disable Command enable PNP Gateway Enable command modify Modify PnP Gateway properties and variables property Show PnP properties and configurationExamples
The following is sample output from the ncs pnp-gateway disable command:
ncs pnp-gateway disable Disabling Plug and Play Gateway..... Plug and Play Gateway is successfully disabled. Please restart Prime Infrastructure on this serverExamples
The following is a sample output of the ncs pnp-gateway enable command:
ncs pnp-gateway enable Enabling Plug and Play Gateway..... Plug and Play Gateway is successfully enabled. Please restart Prime Infrastructure on this server.Examples
The following is a sample output of the ncs pnp-gateway modify command:
ncs pnp-gateway modify bgl-dt-ncs-vm6-70/ayyanna# ncs pnp-gateway modify image ? activation-timeout Activation timeout for PnP image upgrade job distribution-timeout Distribution timeout for PnP image upgrade job transfer-timeout Transfer timeout for PnP image upgrade job bgl-dt-ncs-vm6-70/ayyanna# ncs pnp-gateway modify image activation-timeout ? <60-1048576> Type the image activation timeout value (seconds)Prime Infrastructure PnP Gateway Standalone Server Command
pnp backup
To create a backup of the Cisco Plug and Play Gateway configuration, use the pnp backup command in privileged EXEC mode.
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Usage Guidelines
The backup file is usually created in a compressed tar file format in the disk:/ directory that corresponds to the /localdisk/ directory on the Linux file system.
pnp modify image
To modify the properties of the Cisco Plug and Play Gateway software image in the Prime Infrastructure Plug and Play Standalone Gateway, use the pnp modify image command in privileged EXEC mode.
pnp modify image { activation-timeout | distribution-timeout | transfer-timeout | transfer-timeout } timeout-value
Syntax Description
activation timeout value Activation timeout value, in seconds, for the Cisco Plug and Play Gateway software image upgrade job. The range is from 60 to 1048576. The default is 600.
distribution timeout value Distribution timeout value, in seconds, for the Cisco Plug and Play Gateway software image upgrade job. The valid range is from 60 to 1048576. The default is 1200.
transfer timeout value Transfer timeout value, in seconds, for the Cisco Plug and Play Gateway software image upgrade job. The valid range is from 60 to 1048576. The default is 1200.
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Usage Guidelines
The Cisco Plug and Play Gateway does not have to be restarted for the timeout value to take effect. The timeout value that you specify will take effect for the next software image.
Examples
The following is sample output from the pnp modify image command:
admin# pnp modify image ? activation-timeout Activation timeout for PnP image upgrade job distribution-timeout Distribution timeout for PnP image upgrade job transfer-timeout Transfer timeout for PnP image upgrade job admin# pnp modify image activation-timeout 1200 Done admin# pnp modify image distribution-timeout 2400 Done admin# pnp modify image transfer-timeout 2200 Donepnp modify log-level
To modify the log-level settings of the Cisco Plug and Play Gateway, use the pnp modify log-level command in privileged EXEC mode.
The Cisco Plug and Play Gateway supports these log levels: debug, error, fatal, info, trace, and warn.
Syntax Description
fatal Enables the collection of fatal-level log messages.
error Enables the collection of fatal-level and error-level log messages.
warn Enables the collection of fatal-level, error-level, and warn-level log messages.
info Enables the collection of fatal-level, error-level, warn-level, and information-level log messages.
debug Enables the collection of fatal-level, error-level, warn-level, information-level, and debug-level log messages.
trace Enables the collection of fatal-level, error-level, warn-level, information-level, debug-level, and trace-level log messages.
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Usage Guidelines
The pnp modify log-level command can be used to dynamically change the log level at run time. However, when you restart the Cisco Plug and Play Gateway, it will reset to the error-log level, which is the default.
Examples
The following is sample output from the pnp modify log-level command:
admin# pnp modify log-level ? debug Log level: Debug error Log level: Error fatal Log level: Fatal info Log level: Info trace Log level: Trace warn Log level: Warn admin# pnp modify log-level debug admin# pnp modify log-level error admin# pnp modify log-level fatal admin# pnp modify log-level info admin# pnp modify log-level trace admin# pnp modify log-level warnpnp restore
To restore the configuration settings from an existing backup of the Cisco Plug and Play Gateway, use the pnp restore command in privileged EXEC mode.
To force a restore of the Cisco Plug and Play Gateway settings either when the pnp setup command is in operation or another instance of the pnp restore command is already running, use the pnp restore force command in privileged EXEC mode.
Syntax Description
backup filename Name of the Cisco Plug and Play Gateway backup file whose server settings must be restored.
force Forces a restore of the Cisco Plug and Play Gateway settings.
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Usage Guidelines
When you run the pnp restore command, the server reads the backup files from the /localdisk/ directory. If there is more than one backup file in the /localdisk/ directory, a list of the available backup files is displayed. You must provide the name of the backup file that is to be used for restoring the configuration settings.
After the Cisco Plug and Play Gateway settings have been restored, you are prompted to commit the changes. Press y to commit the changes or n to cancel the restore operation.
Note
You must restart the Cisco Plug and Play Gateway for changes to take effect.
Note
For information on how to copy files to the local disk, see copy command.
Use the pnp restore force command when you have to force a restore operation. This condition is normally seen when different instances of the restore command is already running or when the pnp setup command is in operation. The pnp restore force command forces the restore operation using an existing backup file.
Examples
The following is a sample output of the pnp restore command:
admin# pnp restore ------------------------------------------------ Tue Oct 2 23:05:53 UTC 2012 Restore operation started ------------------------------------------------ Please copy the backup required for restoration. 20121002230546.pnp_backup.tar.gz 20121002224919.pnp_backup.tar.gz Please provide the backup file name [20121002230546.pnp_backup.tar.gz]: Backup Filename used is /localdisk/20121002230546.pnp_backup.tar.gz Commit changes and restart (y/n): ypnp setup
To set up the Cisco Plug and Play Gateway information, use the pnp setup command in privileged EXEC mode.
To forcefully execute a setup operation of the Cisco Plug and Play Gateway when other commands are running and the pnp setup command cannot be used for setting up the server, use the pnp setup force command in privileged EXEC mode.
Note
The pnp setup command can be executed only if Prime Infrastructure and the Cisco Plug and Play Gateway are running on different servers.
Syntax Description
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Examples
The following is sample output from the pnp setup command:
admin# pnp setup ###################################################################### Enter Plug and Play Gateway Setup (setup log /var/KickStart/install/setup.log) For detail information about the parameters in this setup, refer to Plug and Play Gateway Admin Guide. ###################################################################### Enter Prime Infrastructure IP Address: [10.104.105.70] Enable self certificate for server bgl-dt-ncs-vm64-228 (y/n) [y] Self Signed Certificate already available do you want to recreate (y/n)? [n] Automatic download of SSL Certificate is possible if Prime Infrastructure Server is up and running. Automatically download the certificate for server 10.104.105.70 (y/n) [y] The maximum number of Event Gateways allowed is '10' for both plain text and ssl combined. The Event Gateway ports 11011 and 11012 are reserved for port automatic allocation. These ports are not counted while taking the maximum number of ports. Each Event Gateway can serves up to a maximum of 1000 devices. Enter number of Event Gateways that will be started with crypto operation: [5] The maximum number of plain text event gateways ports possible is 5. Enter number of Event Gateways that will be started with plaintext operation: [5] The CNS Event command configures how the managed devices should connect to this particular Plug and Play Gateway. The command entered in the following line should match what's configured on the devices WITHOUT the port number and keyword 'encrypt' if cryptographic is enabled. For example, if the following CLI is configured on devices "cns event bgl-dt-ncs-vm64-228 encrypt 11012 keepalive 120 2 reconnect 10", then `encrypt 11012` should be removed and the below line should be entered : "cns event bgl-dt-ncs-vm64-228 keepalive 120 2 reconnect 10" Another example, if this is a backup Plug and Play Gateway and the following CLI is configured on devices "cns event bgl-dt-ncs-vm64-228 11011 source Vlan1 backup", then `11011` should be removed and the below line should be entered : "cns event bgl-dt-ncs-vm64-228 source Vlan1 backup" Unable to enter a correct CLI could cause the managed devices not be able to connect to this Plug and Play Gateway. For details, please refer to Installation and Configuration Guide. Enter CNS Event command: [cns event bgl-dt-ncs-vm64-228 keepalive 120 2 reconnect 10] Commit changes (y/n): y Attempting to disable the local Plug and Play Gateway in Prime Infrastructure Machine 10.104.105.70 Enter the username to login to the Prime Infrastructure Machine: [admin] ayyanna Enter the password to login to the Prime Infrastructure Machine: Operation Successful. Plug and Play Gateway is successfully disabled. Setup is in progress....... Stop Plug and Play Gateway server Done. Plug and Play Gateway setup completed Start Plug and Play Gateway server.... Done. Plug and Play Gateway server started! ###################################################################### Disabling the local Plug and Play Gateway on Prime Infrastructure server is successful. Please restart the Prime Infrastructure server. ###################################################################### bgl-dt-ncs-vm64-228/admin#
Note
For more information on how to copy files from the local disk, see copy command.pnp setup advanced
To change port level settings, use the pnp setup advanced command in the privileged EXEC mode.
To forcefully execute a setup operation of the Cisco Plug and Play Gateway when other commands are running and the pnp setup advanced command cannot be used for setting up the server, use the pnp setup advanced force command in privileged EXEC mode.
Syntax Description
Command History
Examples
The following is a sample output of the pnp setup advanced command:
pnp setup advanced ###################################################################### Enter Plug and Play Gateway Setup (setup log /var/KickStart/install/setup.log) For detail information about the parameters in this setup, refer to Plug and Play Gateway Admin Guide. ###################################################################### Enter IP Address of Plug and Play Gateway server [10.104.105.228] Enter the fully qualified host name of Plug and Play Gateway server [bgl-dt-ncs-vm64-228] Enter Prime Infrastructure IP Address: [10.104.105.70] Enter Prime Infrastructure Event Port Parameter: [61617] Enable self certificate for server bgl-dt-ncs-vm64-228 (y/n) [y] Self Signed Certificate already available do you want to recreate (y/n)? [n] Automatic download of SSL Certificate is possible if Prime Infrastructure Server is up and running. Automatically download the certificate for server 10.104.105.70 (y/n) [y] Enable secure HTTPS/SSL encryption to secure Plug and Play Gateway Web GUI (y/n) [y] Enter port number for https web access: [443] Enabling clear text operation between Plug and Play Gateway and device(s) increases security risk. Enable clear text operation between device CNS Agent and Plug and Play Gateway (y/n) [y] Enter Tomcat internal port number: [8009] Enter Tomcat shutdown port number: [8005] The maximum number of Event Gateways allowed is '10' for both plain text and ssl combined. The Event Gateway ports 11011 and 11012 are reserved for port automatic allocation. These ports are not counted while taking the maximum number of ports. Each Event Gateway can serves up to a maximum of 1000 devices. Enter number of Event Gateways that will be started with crypto operation: [5] Enter port number for http web access: [80] The maximum number of plain text event gateways ports possible is 5. Enter number of Event Gateways that will be started with plaintext operation: [5] The CNS Event command configures how the managed devices should connect to this particular Plug and Play Gateway. The command entered in the following line should match what's configured on the devices WITHOUT the port number and keyword 'encrypt' if cryptographic is enabled. For example, if the following CLI is configured on devices "cns event bgl-dt-ncs-vm64-228 encrypt 11012 keepalive 120 2 reconnect 10", then `encrypt 11012` should be removed and the below line should be entered : "cns event bgl-dt-ncs-vm64-228 keepalive 120 2 reconnect 10" Another example, if this is a backup Plug and Play Gateway and the following CLI is configured on devices "cns event bgl-dt-ncs-vm64-228 11011 source Vlan1 backup", then `11011` should be removed and the below line should be entered : "cns event bgl-dt-ncs-vm64-228 source Vlan1 backup" Unable to enter a correct CLI could cause the managed devices not be able to connect to this Plug and Play Gateway. For details, please refer to Installation and Configuration Guide. Enter CNS Event command: [cns event bgl-dt-ncs-vm64-228 keepalive 120 2 reconnect 10] Enter IP address for CNS Gateway to listen to. Enter 1 to have CNSGateway listens to all IP addresses. IP addresses:[1] Enter Plug and Play Gateway Event Port Parameter: [62616] Enter base directory for Plug and Play Gateway log : [/var/log] Data directory contains Template and Image files Enter data directory for Plug and Play Gateway : [/var/KickStart] Commit changes (y/n): y Attempting to disable the local Plug and Play Gateway in Prime Infrastructure Machine 10.104.105.70 Enter the username to login to the Prime Infrastructure Machine: [admin] ayyanna Enter the password to login to the Prime Infrastructure Machine: Plug and Play Gateway is already disabled Setup is in progress....... Stop Plug and Play Gateway server Done. Plug and Play Gateway setup completed Start Plug and Play Gateway server.... Done. Plug and Play Gateway server started! admin#pnp start
To start the Cisco Plug and Play Gateway and display the status messages in detail during the startup process, use the pnp start command in privileged EXEC mode.
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Usage Guidelines
Before you execute the pnp start command, stop the Cisco Plug and Play gateway. For more information on stopping the Cisco Plug and Play gateway, refer to the section pnp stop.
Examples
The following is sample output from the pnp start command:
admin# pnp start httpd is stopped Monitoring process started. Plug and Play Gateway start................... Started Event Manager process Starting tomcat... Starting httpd: [ OK ] Starting CNS Gateway: Start of Plug and Play Gateway Completed!! admin#pnp status
To determine the status of the individual tasks and services that are currently running on the Cisco Plug and Play Gateway, use the pnpstatus command in privileged EXEC mode.
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Usage Guidelines
This command can also be used to determine whether the tasks that are running on the Cisco Plug and Play Gateway are secure or nonsecure, and whether the services are up and running or down, along with their port and PID number, where applicable.
Examples
The following is sample output from the pnp status command:
admin# pnp status SERVICE | MODE | STATUS | ADDITIONAL INFO ---------------------------------------------------------------------------------------------------- System | | UP | ---------------------------------------------------------------------------------------------------- Event Messaging Bus | PLAIN TEXT | UP | pid: 3839 CNS Gateway Dispatcher | PLAIN TEXT | UP | pid: 4216, port: 11011 CNS Gateway | PLAIN TEXT | UP | pid: 4245, port: 11013 CNS Gateway | PLAIN TEXT | UP | pid: 4279, port: 11015 CNS Gateway | PLAIN TEXT | UP | pid: 4313, port: 11017 CNS Gateway | PLAIN TEXT | UP | pid: 4404, port: 11019 CNS Gateway | PLAIN TEXT | UP | pid: 4442, port: 11021 CNS Gateway Dispatcher | SSL | UP | pid: 4645, port: 11014 CNS Gateway | SSL | UP | pid: 4645, port: 11014 CNS Gateway | SSL | UP | pid: 4706, port: 11016 CNS Gateway | SSL | UP | pid: 4881, port: 11018 CNS Gateway | SSL | UP | pid: 4921, port: 11020 CNS Gateway | SSL | UP | pid: 4955, port: 11022 HTTPD | | UP | Image Web Service | SSL | UP | Config Web Service | SSL | UP | Resource Web Service | SSL | UP | Image Web Service | PLAIN TEXT | UP | Config Web Service | PLAIN TEXT | UP | Resource Web Service | PLAIN TEXT | UP | Prime Infrastructure Broker | SSL | UP | port: 61617,connection:1pnp stop
To stop the Cisco Plug and Play Gateway and display detailed messages during the stop process, use the pnp stop command in privileged EXEC mode.
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Examples
The following is sample output from the pnp stop command:
admin# pnp stop start status stop bgl-dt-ncs-vm64-228/admin# pnp stop Plug and Play Gateway is being shut down..... Please wait!!! Stopping monitoring process ... Stopping CNS Gateway Processes: Stopping tomcat... Stopping httpd: OK [ OK ] Stopping Event Manager Processes : Stop of Plug and Play Gateway Completed!! admin#pnp tech
To view the environment variables of the Cisco Plug and Play Gateway process, use the pnp tech command in privileged EXEC mode.
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Examples
The following is sample output from the pnp tech command:
admin# pnp tech ------------------------------------------ Cisco Prime Network Control System Plug and Play ------------------------------------------ Environment variables ------------------------------------------ LOGMANAGER_OPTS=-DPNP_LOG_DIR=/var/log/KickStart -Dlog4j.configuration=log4j.properties -DPNP_PROCESS_LOG=logmanager MONITOR_PROCESS=com.cisco.pnp.ks.monitor.Monitor NCS_PNP_WEB_DIR=/opt/CSCOlumos/tomcat/webapps/ PNP_VAR_INSTALL=/var/KickStart/install GREP=grep SETUP_FLAG_FILE=/var/KickStart/install/.setupRunning PNP_ENABLE_AUTH=n GREP_CMD=/bin/grep SED_CMD=/bin/sed KILL_CMD=/bin/kill CNS_ENABLE_AUTO_PASS=y TOMCAT_HOME=/opt/CSCOlumos/KickStart/tomcat NCS_SERVER_CERTIFICATE=/root/server.crt HTTPD_MODULES=/etc/httpd/modules PNP_NCS_MOM_HOST_NAME=127.0.0.1 INIT_DIR=/etc/init.d RPM_CMD=/bin/rpm CNS_ENCRYPT_SERVER_TRUST_STORE=/var/KickStart/install/kickstart.truststore PNP_DATA_BASE=/var LN_CMD=/bin/ln -sf CNS_MAX_NO_DEVICE_PER_PORT=500 PNP_ENABLE_DMZ=y PNP_VAR_TOMCAT_LOG=/var/KickStart/tomcat/logs MKDIR_CMD=/bin/mkdir -p PNP_DEFAULT_NO_OF_PORT=5 PNP_CNS_EVENT_CMD=cns event bgl-pnp-dev1-ovf keepalive 120 2 reconnect 10 TOMCAT_SHUTDOWN_PORT=8005 NCS_PNP_WEBAPP_DIR=/opt/CSCOlumos/tomcat/conf/Catalina/localhost PNP_HTTP_PORT=80 NCS_PROJECT_DISPLAY_NAME=Prime Infrastructure DATE_CMD=/bin/date PNP_LOG_FILE=/var/KickStart/install/pnp_start_stop.log RM_CMD=/bin/rm -f ECHO_CMD=/bin/echo -e TERM=xterm SHELL=NONE PNP_NCS_LIB_DIR=/opt/CSCOlumos/lib/lib_pnp_ks CNS_ENCRYPT_SERVER_KEY_STORE=/var/KickStart/install/kickstart.keystore GREP_ENHANCED_CMD=/bin/grep -E TAR_CMD=/bin/tar ENV_CMD=/bin/env SSH_CLIENT=10.21.84.117 54389 22 PNP_DATE_FORMAT=%Y%m%d%H%M%S PNP_ENABLE_HTTPS=Y CNS_GATEWAY_IP= PNP_LOG_BASE=/var/log PNP_MODJK_PACKAGE=mod_jk-ap20 CATALINA_BASE=/var/KickStart/tomcat TOMCAT_VAR_DIR=/var/KickStart/tomcat SE_ENABLED=0 HOST_NAME_SHORT_CMD=/bin/hostname -s SSH_TTY=/dev/pts/1 PNP_WEBAPP_FILE=/var/KickStart/tomcat/conf/Catalina/localhost/cns.xml PNP_VAR_TOMCAT=/var/KickStart/tomcat PNP_CARSCLI_PACKAGE=PNPCARSCli PNP_BIN=/opt/CSCOlumos/KickStart/bin PNP_JAVA_VERSION=1.6 TOUCH_CMD=/bin/touch CD_CMD=cd USER=admin PNP_IMAGE_TRANSFER_TIMEOUT=1200 CNS_NO_OF_PLAINTEXT_EVENTGW=5 CNS_NO_OF_CRYPTO_EVENTGW=5 PNP_DATA_IMAGE=/var/KickStart/image PNP_ENABLE_SELF_SIGNED=y PNP_ENABLE=Y CPUFILE=/proc/cpuinfo EVT_NCS_EVENT_PROTOCOL=ssl PNP_VAR_HTTPD_CONF=/var/KickStart/httpd/conf MORE_CMD=/bin/more WGET_CMD_SSL=/usr/bin/wget --no-check-certificate HEAD_CMD=/usr/bin/head PNP_PROJECT_RPM_NAME=Lumos_PNP_Server PNP_LOG_DIR=/var/log/KickStart PNP_INSTALL_PREFIX=/opt/CSCOlumos USERNAME_CMD=/usr/bin/id -un IPTABLE=iptables CNS_GATEWAY_OPTS=-DPNP_LOG_DIR=/var/log/KickStart -Dlog4j.configuration=cnslog4j.properties PNP_ENABLE_EMBEDDED_FT=y PNP_HTTPS_PORT=443 PNP_HTTPD_PACKAGE=httpd PNP_IMAGE_ACTIVATION_TIMEOUT=600 PNP_ENABLE_AUTO_NCS=n PNP_ENABLE_SSL=y PNP_BACKUP_NAME=pnp_backup SE_ENABLE_HTTPD_DIR=/usr/bin/chcon -Rv --type=httpd_sys_content_t LOCAL_DISK_DIR=/localdisk COREFILE=unlimited PWD_CMD=pwd MV_CMD=/bin/mv -f PNP_STARTUP_FILE=/var/KickStart/install/cnsGatewayStartup.txt MEMFILE=/proc/meminfo PNP_CE_NG=n MAIL=/var/mail/admin PATH=/bin:/usr/bin:/sbin:/usr/sbin:/usr/local/bin:/usr/local/sbin:/opt/system/bin:/opt/system/lib:/opt/system/etc/carscli IPTABLE_SAVE_CMD=service iptables save IPTABLE_FILE=/etc/sysconfig/iptables EVT_NCS_EVENT_PORT=61617 PNP_NCS=n PNP_SETUP_LOG=/var/KickStart/install/setup.log PNP_HTTPD_INIT_DIR=/opt/CSCOlumos/KickStart/httpd//etc/init.d PNP_HOME=/opt/CSCOlumos/KickStart IPTABLE_RESTART_CMD=service iptables restart PNP_PRIMARY=y EVT_MANAGER_PROCESS=com.cisco.pnp.ks.eventmanager.server.StartPNPKSMOMServer EVT_MGR_EVENT_PORT=62616 PNP_VAR_HTTPD=/var/KickStart/httpd PNP_SYSTEM_MONITOR_NAME=pnp_systemmonitor PWD=/localdisk JAVA_HOME=/usr/lib/jvm/java-1.6.0-sun-1.6.0.21.x86_64/jre HTTP_SERVER_KEY=/var/KickStart/install/pnp_selfsigned_server.key RPM_INSTALL_CMD=/bin/rpm -ivh DF_CMD=/bin/df CP_CMD=/bin/cp -f NCS_TRUST_STORE=/opt/CSCOlumos/conf/truststore DISKSIZE_CMD=/bin/df -lk IPTABLE_ENABLE_TCP_PORT=/sbin/iptables -I INPUT -p tcp -j ACCEPT --dport CAT_CMD=/bin/cat NCS_KEY_STORE=/opt/CSCOlumos/conf/keystore NETSTAT_CMD=/bin/netstat PNP_SERVER_SSL_KEY=/var/KickStart/conf/server.key PNP_HOST_NAME=bgl-pnp-dev1-ovf RPM_REMOVE_CMD=/bin/rpm -e TAIL_CMD=/bin/tail PNP_SERVER_SSL_CERT=/var/KickStart/conf/server.crt CATALINA_OPTS=-DPNP_LOG_DIR=/var/log/KickStart -DPNP_PROCESS_LOG=tomcat CNS_ENABLE_PLAINTEXT=Y HOST_NAME_FULL_CMD=/bin/hostname -f NCS_PNP_WEBAPP_FILE=/opt/CSCOlumos/tomcat/conf/Catalina/localhost/cns.xml PNP_FT_USERNAME=ciscopnp PNP_PROJECT_NAME=KickStart NETCONF_CMD=/sbin/ifconfig AWK_CMD=/bin/awk PNP_ENABLE_PORT_ALLOCATION=y PNP_VAR_HTTPD_HTML=/var/KickStart/httpd/html IPTABLE_STATUS_CMD=service iptables status PNP_SHUTDOWN_FILE=/var/KickStart/install/cnsGatewayShutdown.txt PNP_SERVER_IP=10.104.105.167 PNP_VAR_SERVICE=/var/KickStart/services PNP_DEPLOYMENT_WEBAPP_FILE=/var/KickStart/tomcat/webapps/pnp-deployment-service.war NCS_LOG_BASE=/opt/CSCOlumos/logs PNP_VAR_CONF=/var/KickStart/conf SHLVL=3 HOME=/home/admin PNP_JAVA_OPTS=-DPNP_LOG_DIR=/var/log/KickStart -DPNP_PROCESS_LOG=tomcat PNP_LIB=/opt/CSCOlumos/KickStart/lib PS_CMD=/bin/ps WGET_CMD=/usr/bin/wget DIFF_CMD=/usr/bin/diff EVT_MGR_OPTS=-DPNP_LOG_DIR=/var/log/KickStart -DPNP_PROCESS_LOG=evtmgr HTTPD_CONF=/var/KickStart/httpd/conf PNP_DATA_DIR=/var/KickStart CUT_CMD=/bin/cut PNP_DATA_TEMPLATE=/var/KickStart/template PNP_PROJECT_RELEASE=1 MONITOR_OPTS=-DPNP_LOG_DIR=/var/log/KickStart -Dlog4j.configuration=monitorlog4j.properties -DPNP_PROCESS_LOG=monitor TOMCAT_LOG_DIR=/var/log/KickStart/tomcat SESTATUS_CMD=/usr/sbin/sestatus OPENSSL_CMD=/usr/bin/openssl LOGNAME=admin PNP_NCS_CONTEXT_FILE=/opt/CSCOlumos/conf/pnp-ks-bean-context.xml EVT_MGR_EVENT_PROTOCOL=tcp PNP_END_PORT_STANDALONE=12010 DU_CMD=/usr/bin/du CLASSPATH=:/var/KickStart/conf NCS_PNP_DEPLOYMENT_WEBAPP_DIR=/opt/CSCOlumos/tomcat/webapps/pnp-deployment-service IPTABLE_STOP_CMD=service iptables stop PNP_PROJECT_VERSION=2.0.0.0 SSH_CONNECTION=10.21.84.117 54389 10.104.105.167 22 PNP_FT_PORT=21 PNP_PLAINTEXT_HTTPD=y PNP_PROJECT_DISPLAY_NAME=PnP Gateway PNP_START_PORT=11011 PNP_SETUP_COUNT=1 TOMCAT_AJP13_PORT=8009 MAXOPENFILE=4096 RPM_QUERY_PKG_CMD=/bin/rpm -qi NCS_PROJECT_NAME=NCS PNP_DATA=/var/KickStart PNP_HOME_HTTPD=/opt/CSCOlumos/KickStart/httpd CNS_TOTAL_EVENTGW=10 HTTP_SERVER_CERTIFICATE=/var/KickStart/install/pnp_self_signedserver.crt EVT_MGR_EVENT_FAILOVER=y LS_CMD=/bin/ls NCS_INSTALL_PREFIX=/opt/CSCOlumos NCS_PKG_NAME=LumosApp PNP_LOG4J_OPTS=-DPNP_LOG_DIR=/var/log/KickStart PNP_VAR_TOMCAT_CONF=/var/KickStart/tomcat/conf PNP_VAR_DIR=/var/KickStart SLEEP_CMD=/bin/sleep PNP_IMAGE_DISTRIBUTION_TIMEOUT=1200 EVT_MGR_NETWORK_IP=10.104.105.167 RPM_FORCED_REMOVE_CMD=/bin/rpm -e --force --noscripts PNP_LOG_LEVEL=warn HTTPD_HOME=/usr PNP_FT_PROTOCOL=ftp CNS_GATEWAY_PROCESS=com.cisco.pnp.ks.cnsgateway.connection.ConnectionManagerBean SE_DEL_HTTPD_MUTEX=/bin/rm -f -r /etc/httpd/logs/ssl_mutex* PNP_END_PORT_NCS=11014 _=/bin/env ------------------------------------------ admin#pnp tech log
To create a system-monitoring log file for the Cisco Plug and Play Gateway, use the pnp tech log command in privileged EXEC mode.
Command History
Release Modification Cisco Prime Infrastructure 1.2 This command was introduced.
Cisco Prime Infrastructure 2.0 This command was modified.
Usage Guidelines
The pnp tech log command creates a system-monitoring log file in a compressed tar format with the extension .pnp_systemmonitor.tar.gz.
Examples
The following is sample output from the pnp tech log command:
admin# pnp tech log The System Status file created : /localdisk/20121003032209.pnp_systemmonitor.tar.gz admin#
Note
For more information on how to copy files from the local disk, see copy command.show Commands
- show application
- show backup history
- show cdp
- show clock
- show cpu
- show disks
- show icmp-status
- show interface
- show inventory
- show logging
- show logins
- show memory
- show ntp
- show ports
- show process
- show repository
- show restore
- show running-config
- show startup-config
- show tech-support
- show terminal
- show timezone
- show timezones
- show udi
- show uptime
- show users
- show version
show application
To show application information of the installed application packages on the system, use the show application command in EXEC mode.
show application [status | version [app_name]]
Syntax Description
status
Displays the status of the installed application.
version
Displays the application version for an installed application—the Prime Infrastructure.
app_name
Name of the installed application.
Table 7 Output Modifier Variables for Count or Last |
Output modifier variables:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counts the number of lines in the output. Add number after the word count. |—Output modifier variables.
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludes lines that match. Up to 80 alphanumeric characters.
- include—Includes lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10. |—Output modifier variables (see Table A-8 ).
Examples
Example 1
ncs/admin# show application <name> <Description> ncs Cisco Network Control System ncs/admin#Example 2
ncs/admin# show application version NCS Cisco Network Control System --------------------------------------------- Version : 1.0.2.051 Build Date : Mon Aug 2 00:34:25 2010 Install Date : Thu Aug 5 17:48:49 2010 ncs/admin#Example 3
ncs/admin# show application status NCS NCS Database listener is running, PID: 21096 NCS Database is running, number of processes: 27 NCS Application Server is running, PID: 21432 NCS M&T Session Database is running, PID: 21365 NCS M&T Log Collector is running, PID: 21468 NCS M&T Log Processor is running, PID: 21494 NCS M&T Alert Process is running, PID: 21524 ncs/admin#show backup history
Examples
Example 1
ncs/admin# show backup history Wed Aug 18 12:55:21 UTC 2010: backup logs logs-0718.tar.gz to repository fileserver007: success Wed Aug 18 12:55:53 UTC 2010: backup full-0718.tar.gpg to repository fileserver007: success ncs/admin#Example 2
ncs/admin# show backup history backup history is empty ncs/admin#Related Commands
Command
Description
Performs a backup ( Prime Infrastructure and Cisco ADE OS) and places the backup in a repository.
Restores from backup the file contents of a specific repository.
Enters the repository submode for configuration of backups.
Displays the available backup files located on a specific repository.
show cdp
To display information about the enabled Cisco Discovery Protocol interfaces, use the show cdp command in EXEC mode.
show cdp {all | neighbors}
Syntax Description
all
Shows all of the enabled Cisco Discovery Protocol interfaces.
neighbors
Shows the Cisco Discovery Protocol neighbors.
Examples
Example 1
ncs/admin# show cdp all CDP protocol is enabled ... broadcasting interval is every 60 seconds. time-to-live of cdp packets is 180 seconds. CDP is enabled on port GigabitEthernet0. ncs/admin#Example 2
ncs/admin# show cdp neighbors CDP Neighbor : 000c297840e5 Local Interface : GigabitEthernet0 Device Type : L-NCS-1.0-50 Port : eth0 Address : 172.23.90.114 CDP Neighbor : isexp-esw5 Local Interface : GigabitEthernet0 Device Type : cisco WS-C3560E-24TD Port : GigabitEthernet0/5 Address : 172.23.90.45 CDP Neighbor : 000c29e29926 Local Interface : GigabitEthernet0 Device Type : L-NCS-1.0-50 Port : eth0 Address : 172.23.90.115 CDP Neighbor : 000c290fba98 Local Interface : GigabitEthernet0 Device Type : L-NCS-1.0-50 Port : eth0 Address : 172.23.90.111 ncs/admin#Related Commands
show clock
To display the day, month, date, time, time zone, and year of the system software clock, use the show clock command in EXEC mode.
show cpu
Syntax Description
statistics
Displays CPU statistics.
|
Output modifier variables:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counts the number of lines in the output. Add number after the word count. |—Output modifier variables (see Table A-9 ).
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludes lines that match. Up to 80 alphanumeric characters.
- include—Includes lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10. |—Output modifier variables (see Table A-9 ).
Examples
Example 1
ncs/admin# show cpu processor : 0 model : Intel(R) Xeon(R) CPU E5320 @ 1.86GHz speed(MHz): 1861.914 cache size: 4096 KB ncs/admin#Example 2
ncs/admin# show cpu statistics user time: 265175 kernel time: 166835 idle time: 5356204 i/o wait time: 162676 irq time: 4055 ncs/admin#show disks
To display the disks file-system information, use the show disks command in EXEC mode.
show disks [|] [|]
Syntax Description
|
Output modifier variables:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counts the number of lines in the output. Add number after the word count. |—Output modifier variables (see Table A-10 ).
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludes lines that match. Up to 80 alphanumeric characters.
- include—Includes lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10. |—Output modifier variables (see Table A-10 ).
Examples
ncs/admin# show disks temp. space 2% used (17828 of 988116) disk: 3% used (143280 of 5944440) Internal filesystems: all internal filesystems have sufficient free space ncs/admin#show icmp-status
To display the Internet Control Message Protocol echo response configuration information, use the show icmp_status command in EXEC mode.
show icmp_status {> file | |}
Syntax Description
>
Output direction.
file
Name of file to redirect standard output (stdout).
|
Output modifier commands:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counts the number of lines in the output. Add number after the word count.
- |—Output modifier commands (see Table A-11 ).
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludes lines that match. Up to 80 alphanumeric characters.
- include—Includes lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10.
- |—Output modifier commands (see Table A-11 ).
Examples
Example 1
ncs/admin# show icmp_status icmp echo response is turned on ncs/admin#Example 2
ncs/admin# show icmp_status icmp echo response is turned off ncs/admin#show interface
To display the usability status of interfaces configured for IP, use the show interface command in EXEC mode.
show interface [GigabitEthernet] |
Syntax Description
GigabitEthernet
Shows the Gigabit Ethernet interface. Either 0 or 1.
|
Output modifier variables:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counts the number of lines in the interface. Add number after the word count.
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludse lines that match. Up to 80 alphanumeric characters.
- include—Includes lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10.
Usage Guidelines
In the show interface GigabitEthernet 0 output, you can find that the interface has three IPv6 addresses. The first internet address (starting with 3ffe) is the result of using stateless autoconfiguration. For this to work, you need to have IPv6 route advertisement enabled on that subnet. The next address (starting with fe80) is a link local address that does not have any scope outside the host. You always see a link local address regardless of the IPv6 autoconfiguration or DHCPv6 configuration. The last address (starting with 2001) is the result obtained from an IPv6 DHCP server.
Examples
Example 1
ncs/admin# show interface eth0 Link encap:Ethernet HWaddr 00:0C:29:6A:88:C4 inet addr:172.23.90.113 Bcast:172.23.90.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe6a:88c4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:48536 errors:0 dropped:0 overruns:0 frame:0 TX packets:14152 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6507290 (6.2 MiB) TX bytes:12443568 (11.8 MiB) Interrupt:59 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1195025 errors:0 dropped:0 overruns:0 frame:0 TX packets:1195025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:649425800 (619.3 MiB) TX bytes:649425800 (619.3 MiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) ncs/admin#Example 2
ncs/admin# show interface GigabitEthernet 0 eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:DA:05 inet addr:172.23.90.116 Bcast:172.23.90.255 Mask:255.255.255.0 inet6 addr: 3ffe:302:11:2:20c:29ff:feaf:da05/64 Scope:Global inet6 addr: fe80::20c:29ff:feaf:da05/64 Scope:Link inet6 addr: 2001:558:ff10:870:8000:29ff:fe36:200/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77848 errors:0 dropped:0 overruns:0 frame:0 TX packets:23131 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10699801 (10.2 MiB) TX bytes:3448374 (3.2 MiB) Interrupt:59 Base address:0x2000show inventory
To display information about the hardware inventory, including the Prime Infrastructure appliance model and serial number, use the show inventory command in EXEC mode.
show inventory |
Syntax Description
|
Output modifier variables:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counts the number of lines in the interface. Add number after the word count.
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludse lines that match. Up to 80 alphanumeric characters.
- include—Includes lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10.
Examples
ncs/admin# show inventory NAME: "L-NCS-1.0-50 chassis", DESCR: "L-NCS-1.0-50 chassis" PID: L-NCS-1.0-50 , VID: V01 , SN: H8JESGOFHGG Total RAM Memory: 1035164 kB CPU Core Count: 1 CPU 0: Model Info: Intel(R) Xeon(R) CPU E5320 @ 1.86GHz Hard Disk Count(*): 1 Disk 0: Device Name: /dev/sda Disk 0: Capacity: 64.40 GB Disk 0: Geometry: 255 heads 63 sectors/track 7832 cylinders NIC Count: 1 NIC 0: Device Name: eth0 NIC 0: HW Address: 00:0C:29:6A:88:C4 NIC 0: Driver Descr: eth0: registered as PCnet/PCI II 79C970A (*) Hard Disk Count may be Logical. ncs/admin#show logging
To display the state of system logging (syslog) and the contents of the standard system logging buffer, use the show logging command in EXEC mode.
show logging {application [application-name]} {internal} {system} |
Syntax Description
application
Displays application logs.
application-name
Application name. Up to 255 alphanumeric characters.
internal
Displays the syslogs configuration.
system
Displays the system syslogs.
|
Output modifier variables:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counts the number of lines in the interface. Add number after the word count.
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludes lines that match. Up to 80 alphanumeric characters.
- include—Includes lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10.
Usage Guidelines
This command displays the state of syslog error and event logging, including host addresses, and for which, logging destinations (console, monitor, buffer, or host) logging is enabled.
Examples
Example 1
ncs/admin# show logging system ADEOS Platform log: ----------------- Aug 5 10:44:32 localhost debugd[1943]: [16618]: config:network: main.c[252] [setup]: Setup is complete Aug 5 10:45:02 localhost debugd[1943]: [17291]: application:install cars_install.c[242] [setup]: Install initiated with bundle - ncs.tar.gz, repo - SystemDefaultPkgRepos Aug 5 10:45:02 localhost debugd[1943]: [17291]: application:install cars_install.c[256] [setup]: Stage area - /storeddata/Installing/.1281030 302 Aug 5 10:45:02 localhost debugd[1943]: [17291]: application:install cars_install.c[260] [setup]: Getting bundle to local machine Aug 5 10:45:03 localhost debugd[1943]: [17291]: transfer: cars_xfer.c[58] [setup]: local copy in of ncs.tar.gz requested Aug 5 10:45:46 localhost debugd[1943]: [17291]: application:install cars_install.c[269] [setup]: Got bundle at - /storeddata/Installing/.1281 030302/ncs.tar.gz Aug 5 10:45:46 localhost debugd[1943]: [17291]: application:install cars_install.c[279] [setup]: Unbundling package ncs.tar.gz Aug 5 10:47:06 localhost debugd[1943]: [17291]: application:install cars_install.c[291] [setup]: Unbundling done. Verifying input parameters. .. Aug 5 10:47:06 localhost debugd[1943]: [17291]: application:install cars_install.c[313] [setup]: Manifest file is at - /storeddata/Installing /.1281030302/manifest.xml Aug 5 10:47:07 localhost debugd[1943]: [17291]: application:install cars_install.c[323] [setup]: Manifest file appname - ncs Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install cars_install.c[386] [setup]: Manifest file pkgtype - CARS Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install cars_install.c[398] [setup]: Verify dependency list - Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install cars_install.c[410] [setup]: Verify app license - Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install cars_install.c[420] [setup]: Verify app RPM's Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install cars_install.c[428] [setup]: No of RPM's - 9 Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install cars_install.c[439] [setup]: Disk - 50 Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install ci_util.c[325] [setup]: Disk requested = 51200 KB Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install ci_util.c[345] [setup]: More disk found Free = 40550400, req_disk = 51200 Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install cars_install.c[450] [setup]: Mem requested by app - 100 Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install ci_util.c[369] [setup]: Mem requested = 102400 Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install ci_util.c[384] [setup]: Found MemFree = MemFree: 13028 kB Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install ci_util.c[390] [setup]: Found MemFree value = 13028 Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install ci_util.c[393] [setup]: Found Inactive = Inactive: 948148 kB Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install ci_util.c[399] [setup]: Found Inactive MemFree value = 948148 Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install ci_util.c[409] [setup]: Sufficient mem found Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install ci_util.c[415] [setup]: Done checking memory... Aug 5 10:47:09 localhost debugd[1943]: [17291]: application:install cars_install.c[461] [setup]: Verifying RPM's... --More-- (press Spacebar to continue)Example 2
ncs/admin# show logging internal log server: localhost Global loglevel: 6 Status: Enabled ncs/admin#Example 3
ncs/admin# show logging internal log server: localhost Global loglevel: 6 Status: Disabled ncs/admin#show logins
Syntax Description
Examples
ncs/admin# show logins cli admin pts/0 10.77.137.60 Fri Aug 6 09:45 still logged in admin pts/0 10.77.137.60 Fri Aug 6 08:56 - 09:30 (00:33) admin pts/0 10.77.137.60 Fri Aug 6 07:17 - 08:43 (01:26) reboot system boot 2.6.18-164.el5PA Thu Aug 5 18:17 (17:49) admin tty1 Thu Aug 5 18:15 - down (00:00) reboot system boot 2.6.18-164.el5PA Thu Aug 5 18:09 (00:06) setup tty1 Thu Aug 5 17:43 - 18:07 (00:24) reboot system boot 2.6.18-164.el5PA Thu Aug 5 16:05 (02:02) wtmp begins Thu Aug 5 16:05:36 2010 ncs/admin#show memory
show ntp
Examples
ncs/admin# show ntp Primary NTP : cd-ncs-ntp.cisco.com synchronised to NTP server (10.56.60.29) at stratum 3 time correct to within 99 ms polling server every 1024 s remote refid st t when poll reach delay offset jitter ============================================================================== 127.127.1.0 .LOCL. 10 l 36 64 377 0.000 0.000 0.001 *10.56.60.29 64.103.34.15 2 u 906 1024 377 270.657 3.831 14.345 Warning: Output results may conflict during periods of changing synchronization. ncs/admin# ncs/admin# show ntp % no NTP servers configured ncs/admin#show ports
To display information about all of the processes listening on active ports, use the show ports command in EXEC mode.
show ports [|] [|]
Syntax Description
|
Output modifier variables:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counts the number of lines in the interface. Add number after the word count. |—Output modifier variables (see Table A-12 ).
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludes lines that match. Up to 80 alphanumeric characters.
- include—Includes lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10. |—Output modifier variables (see Table A-12 ).
Usage Guidelines
When you run the show ports command, the port must have an associated active session.
Examples
ncs/admin# show ports Process : timestensubd (21372) tcp: 127.0.0.1:11298 Process : timestenorad (21609) tcp: 127.0.0.1:51715 udp: ::1:28314, ::1:59055, ::1:45113, ::1:49082, ::1:64737, ::1:62570, ::1:19577, ::1:29821 Process : ttcserver (21382) tcp: 127.0.0.1:16612, 0.0.0.0:53385 Process : timestenrepd (21579) tcp: 127.0.0.1:62504, 0.0.0.0:18047 udp: ::1:51436 Process : timestend (21365) tcp: 0.0.0.0:53384 Process : rpc.statd (2387) tcp: 0.0.0.0:873 udp: 0.0.0.0:867, 0.0.0.0:870 Process : timestensubd (21373) tcp: 127.0.0.1:43407 Process : portmap (2350) tcp: 0.0.0.0:111 udp: 0.0.0.0:111 Process : Decap_main (21468) tcp: 0.0.0.0:2000 udp: 0.0.0.0:9993 Process : timestensubd (21369) tcp: 127.0.0.1:37648 Process : timestensubd (21374) tcp: 127.0.0.1:64211 Process : sshd (2734) tcp: 172.23.90.113:22 Process : java (21432) tcp: 127.0.0.1:8888, :::2080, :::2020, ::ffff:127.0.0.1:8005, :::8009, :::8905, :::8010, :::2090, :::1099, :::9999, :::61616, :::8080, :: :80, :::60628, :::8443, :::443 udp: 0.0.0.0:1812, 0.0.0.0:1813, 0.0.0.0:1700, 0.0.0.0:10414, 0.0.0.0:3799, 0.0.0.0:1645, 0.0.0.0:1646, :::8905, :::8906 Process : monit (21531) tcp: 127.0.0.1:2812 Process : java (21524) tcp: :::62627 Process : java (21494) tcp: ::ffff:127.0.0.1:20515 udp: 0.0.0.0:20514 Process : tnslsnr (21096) tcp: :::1521 Process : ora_d000_ncs1 (21222) tcp: :::26456 udp: ::1:63198 Process : ntpd (2715) udp: 172.23.90.113:123, 127.0.0.1:123, 0.0.0.0:123, ::1:123, fe80::20c:29ff:fe6a:123, :::123 Process : ora_pmon_ncs1 (21190) udp: ::1:51994 Process : ora_mmon_ncs1 (21218) udp: :::38941 Process : ora_s000_ncs1 (21224) udp: ::1:49864 ncs/admin#show process
To display information about active processes, use the show process command in the EXEC mode.
show process |
Syntax Description
|
(Optional) Output modifier variables:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counst the number of lines in the interface. Add number after the word count.
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludes lines that match. Up to 80 alphanumeric characters.
- include—Includes lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10.
Examples
ncs/admin# show processUSER PID TIME TT COMMAND
root 1 00:00:02 ? init
root 2 00:00:00 ? migration/0
root 3 00:00:00 ? ksoftirqd/0
root 4 00:00:00 ? watchdog/0
root 5 00:00:00 ? events/0
root 6 00:00:00 ? khelper
root 7 00:00:00 ? kthread
root 10 00:00:01 ? kblockd/0
root 11 00:00:00 ? kacpid
root 170 00:00:00 ? cqueue/0
root 173 00:00:00 ? khubd
root 175 00:00:00 ? kseriod
root 239 00:00:32 ? kswapd0
root 240 00:00:00 ? aio/0
root 458 00:00:00 ? kpsmoused
root 488 00:00:00 ? mpt_poll_0
root 489 00:00:00 ? scsi_eh_0
root 492 00:00:00 ? ata/0
root 493 00:00:00 ? ata_aux
root 500 00:00:00 ? kstriped
root 509 00:00:07 ? kjournald
root 536 00:00:00 ? kauditd
root 569 00:00:00 ? udevd
root 1663 00:00:00 ? kmpathd/0
root 1664 00:00:00 ? kmpath_handlerd
root 1691 00:00:00 ? kjournald
root 1693 00:00:00 ? kjournald
root 1695 00:00:00 ? kjournald
root 1697 00:00:00 ? kjournald
root 2284 00:00:00 ? auditd
root 2286 00:00:00 ? audispd
root 2318 00:00:10 ? debugd
rpc 2350 00:00:00 ? portmap
root 2381 00:00:00 ? rpciod/0
--More--
ncs/admin#
show repository
To display the file contents of the repository, use the show repository command in EXEC mode.
show repository repository-name
Syntax Description
repository-name
Name of the repository whose contents you want to view. Up to 30 alphanumeric characters.
Related Commands
show restore
Syntax Description
Examples
Example 1ncs/admin# show restore history ncs/admin#Example 2ncs/admin# show restore history restore history is empty ncs/admin#Related Commands
show running-config
To display the contents of the currently running configuration file or the configuration, use the show running-config command in EXEC mode.
Examples
ncs/admin# show running-config Generating configuration... ! hostname ncs ! ip domain-name cisco.com ! interface GigabitEthernet 0 ip address 172.23.90.113 255.255.255.0 ipv6 address autoconfig ! ip name-server 172.16.168.183 ! ip default-gateway 172.23.90.1 ! clock timezone UTC ! ntp server time.nist.gov ! username admin password hash $1$JbbHvKVG$xMZ/XL4tH15Knf.FfcZZr. role admin ! service sshd ! password-policy lower-case-required upper-case-required digit-required no-username disable-cisco-passwords min-password-length 6 ! logging localhost logging loglevel 6 ! cdp timer 60 cdp holdtime 180 cdp run GigabitEthernet 0 ! icmp echo on ! ncs/admin#show startup-config
To display the contents of the startup configuration file or the configuration, use the show startup-config command in EXEC mode.
Command Default
The show startup-config command displays all of the startup configuration information.
Examples
ncs/admin# show startup-config ! hostname ncs ! ip domain-name cisco.com ! interface GigabitEthernet 0 ip address 172.23.90.113 255.255.255.0 ipv6 address autoconfig ! ip name-server 172.16.168.183 ! ip default-gateway 172.23.90.1 ! clock timezone UTC ! ntp server time.nist.gov ! username admin password hash $1$JbbHvKVG$xMZ/XL4tH15Knf.FfcZZr. role admin ! service sshd ! password-policy lower-case-required upper-case-required digit-required no-username disable-cisco-passwords min-password-length 6 ! logging localhost logging loglevel 6 ! cdp timer 60 cdp holdtime 180 cdp run GigabitEthernet 0 ! icmp echo on ! ncs/admin#show tech-support
To display technical support information, including email, use the show tech-support command in EXEC mode.
show tech-support file [word]
Syntax Description
file
Saves any technical support data as a file in the local disk.
word
Filename to save. Up to 80 alphanumeric characters.
Usage Guidelines
The show tech-support command is useful for collecting a large amount of information about your Prime Infrastructure server for troubleshooting purposes. You can then provide output to technical support representatives when reporting a problem.
Examples
ncs/admin# show tech-support ################################################### Application Deployment Engine(ADE) - 2.0.0.568 Technical Support Debug Info follows... ################################################### ***************************************** Checking dmidecode Serial Number(s) ***************************************** None VMware-56 4d 14 cb 54 3d 44 5d-49 ee c4 ad a5 6a 88 c4 ***************************************** Displaying System Uptime... ***************************************** 12:54:34 up 18:37, 1 user, load average: 0.14, 0.13, 0.12 ***************************************** Display Memory Usage(KB) ***************************************** total used free shared buffers cached Mem: 1035164 1006180 28984 0 10784 345464 -/+ buffers/cache: 649932 385232 Swap: 2040244 572700 1467544 ***************************************** Displaying Processes(ax --forest)... ***************************************** PID TTY STAT TIME COMMAND 1 ? Ss 0:02 init [3] 2 ? S< 0:00 [migration/0] 3 ? SN 0:00 [ksoftirqd/0] 4 ? S< 0:00 [watchdog/0] 5 ? S< 0:00 [events/0] --More-- (press Spacebar to continue) ncs/admin#show terminal
To obtain information about the terminal configuration parameter settings, use the show terminal command in EXEC mode.
Examples
ncs/admin# show terminal TTY: /dev/pts/0 Type: "vt100" Length: 27 lines, Width: 80 columns Session Timeout: 30 minutes ncs/admin#show terminal describes the fields of the show terminal output.
Table 9 Show Terminal Field Descriptions Field
Description
TTY: /dev/pts/0
Displays standard output to type of terminal.
Type: “vt100“
Type of current terminal used.
Length: 24 lines
Length of the terminal display.
Width: 80 columns
Width of the terminal display, in character columns.
Session Timeout: 30 minutes
Length of time, in minutes, for a session, after which the connection closes.
show timezone
show timezones
To obtain a list of time zones from which you can select, use the show timezones command in EXEC mode.
Usage Guidelines
See the clock timezone, page A-95 command, for examples of the time zones available for the Prime Infrastructure server.
Examples
ncs/admin# show timezones Africa/Blantyre Africa/Dar_es_Salaam Africa/Dakar Africa/Asmara Africa/Timbuktu Africa/Maputo Africa/Accra Africa/Kigali Africa/Tunis Africa/Nouakchott Africa/Ouagadougou Africa/Windhoek Africa/Douala Africa/Johannesburg Africa/Luanda Africa/Lagos Africa/Djibouti Africa/Khartoum Africa/Monrovia Africa/Bujumbura Africa/Porto-Novo Africa/Malabo Africa/Ceuta Africa/Banjul Africa/Cairo Africa/Mogadishu Africa/Brazzaville Africa/Kampala Africa/Sao_Tome Africa/Algiers Africa/Addis_Ababa Africa/Ndjamena Africa/Gaborone Africa/Bamako Africa/Freetown --More-- (press Spacebar to continue) ncs/admin#show udi
show uptime
To display the length of time that you have been logged in to the Prime Infrastructure server, use the show uptime command in EXEC mode.
show uptime |
Syntax Description
|
(Optional) Output modifier variables:
- begin—Matched pattern. Up to 80 alphanumeric characters.
- count—Counts the number of lines in the output. Add number after the word count.
- end—Ends with line that matches. Up to 80 alphanumeric characters.
- exclude—Excludes lines that match. Up to 80 alphanumeric characters.
- include—Includse lines that match. Up to 80 alphanumeric characters.
- last—Displays last few lines of output. Add number after the word last. Up to 80 lines to display. Default 10.
show users
show version
To display information about the software version of the system, use the show version command in EXEC mode.
Usage Guidelines
This command displays version information about the Cisco ADE-OS software running on the Prime Infrastructure server, and displays the Prime Infrastructure version.
Examples
ncs/admin# show version Cisco Application Deployment Engine OS Release: 2.0 ADE-OS Build Version: 2.0.0.568 ADE-OS System Architecture: i386 Copyright (c) 2005-2010 by Cisco Systems, Inc. All rights reserved. Hostname: pmbudev-vm3 Version information of installed applications --------------------------------------------- Cisco Prime Network Control System --------------------------------------------- Version : 1.0.2.051 Vendor : Wireless Networking Business Unit ncs/admin#Configuration Commands
This section lists the configuration commands along with a brief description of their use, command defaults, command syntax, command modes, usage guidelines, command examples, and related commands, where applicable.
Configuration commands include interface and repository.
NoteSome of the configuration commands require you to enter the configuration submode to complete the command configuration.
To access configuration mode, you must use the configure command in EXEC mode.
- backup-staging-url
- cdp holdtime
- cdp run
- cdp timer
- clock timezone
- do
- end
- exit
- hostname
- icmp echo
- interface
- ipv6 address autoconfig
- ipv6 address dhcp
- ip address
- ip default-gateway
- ip domain-name
- ip name-server
- ip route
- kron occurrence
- kron policy-list
- logging
- ntp server
- password-policy
- repository
- service
- shutdown
- snmp-server community
- snmp-server contact
- snmp-server host
- snmp-server location
- username
backup-staging-url
To allow you to configure a Network File System (NFS) location that the backup and restore operations will use as a staging area to package and unpackage backup files, use the backup-staging-url command in configuration mode.
Syntax Description
word
NFS URL for staging area. Up to 2048 alphanumeric characters. Use nfs://server:path(1) .
cdp holdtime
To specify the amount of time for which the receiving device should hold a Cisco Discovery Protocol packet from the Prime Infrastructure server before discarding it, use the cdp holdtime command in configuration mode. To revert to the default setting, use the no form of this command.
Syntax Description
Usage Guidelines
Cisco Discovery Protocol packets transmit with a time to live, or hold time, value. The receiving device will discard the Cisco Discovery Protocol information in the Cisco Discovery Protocol packet after the hold time has elapsed.
The cdp holdtime command takes only one argument; otherwise, an error occurs.
cdp run
To enable the Cisco Discovery Protocol, use the cdp run command in configuration mode. To disable the Cisco Discovery Protocol, use the no form of this command.
Syntax Description
GigabitEthernet
Specifies the Gigabit Ethernet interface on which to enable the Cisco Discovery Protocol.
Usage Guidelines
The command has one optional argument, which is an interface name. Without an optional interface name, the command enables the Cisco Discovery Protocol on all interfaces.
NoteThe default for this command is on interfaces that are already up and running. When you are bringing up an interface, stop the Cisco Discovery Protocol first; then, start the Cisco Discovery Protocol again.
cdp timer
To specify how often the Prime Infrastructure server sends Cisco Discovery Protocol updates, use the cdp timer command in configuration mode. To revert to the default setting, use the no form of this command.
Syntax Description
seconds
Specifies how often, in seconds, the Prime Infrastructure server sends Cisco Discovery Protocol updates. Value from 5 to 254 seconds.
Usage Guidelines
Cisco Discovery Protocol packets transmit with a time to live, or hold time, value. The receiving device will discard the Cisco Discovery Protocol information in the Cisco Discovery Protocol packet after the hold time has elapsed.
The cdp timer command takes only one argument; otherwise, an error occurs.
clock timezone
To set the time zone, use the clock timezone command in configuration mode. To disable this function, use the no form of this command.
Syntax Description
Usage Guidelines
The system internally keeps time in Coordinated Universal Time (UTC). If you do not know your specific time zone, you can enter the region, country, and city (see Tables A-16, A-17, and A-18 for sample time zones to enter on your system).
3 (1) Enter the country and city together with a forward slash (/) between them; for example, Australia/Currie.4 (2) ACT = Australian Capital Territory5 (3) LHI = Lord Howe Island6 (4) NSW = New South Wales7 (1) The Asia time zone includes cities from East Asia, Southern Southeast Asia, West Asia, and Central Asia.8 (2) Enter the region and city or country together separated by a forward slash (/); for example, Asia/Aden.
NoteSeveral more time zones are available to you. On your Prime Infrastructure server, enter the show timezones command. A list of all of the time zones available in the Prime Infrastructure server appears. Choose the most appropriate one for your time zone.
Examples
ncs/admin(config)# clock timezone EST ncs/admin(config)# exit ncs/admin# show timezone EST ncs/admin#do
To execute an EXEC-level command from configuration mode or any configuration submode, use the do command in any configuration mode.
Table 13 Command Options for the Do Command Performs a backup ( Prime Infrastructure and Cisco ADE OS) and places the backup in a repository.
Performs a backup of all of the logs on the Prime Infrastructure server to a remote location.
Displays any errors or events for various command situations; for example, backup and restore, configuration, copy, resource locking, file transfer, and user management.
Forces the logout of all of the sessions of a specific Prime Infrastructure node user.
Describes the help utility and how to use it on the Prime Infrastructure server.
Determines the IPv6 network activity on a IPv6 remote system.
Performs a restore and retrieves the backup out of a repository.
Sets the welcome message on the system for all terminal sessions.
Specifies the type of terminal connected to the current line of the current session.
Disables the output (display of errors or events) of the debug command for various command situations; for example, backup and restore, configuration, copy, resource locking, file transfer, and user management.
Erases the startup configuration that forces the setup utility to run and prompts the network configuration, copies the running configuration to the startup configuration, and displays the running configuration on the console.
Usage Guidelines
Use this command to execute EXEC commands (such as show, clear, and debug commands) while configuring your server. After the EXEC command executes, the system will return to the configuration mode that you were using.
Examples
ncs/admin(config)# do show run Generating configuration... ! hostname ncs ! ip domain-name cisco.com ! interface GigabitEthernet 0 ip address 172.23.90.113 255.255.255.0 ipv6 address autoconfig ! ip name-server 172.16.168.183 ! ip default-gateway 172.23.90.1 ! clock timezone EST ! ntp server time.nist.gov ! username admin password hash $1$JbbHvKVG$xMZ/XL4tH15Knf.FfcZZr. role admin ! service sshd ! backup-staging-url nfs://loc-filer02a:/vol/local1/private1/jdoe ! password-policy lower-case-required upper-case-required digit-required no-username disable-cisco-passwords min-password-length 6 ! logging localhost logging loglevel 6 ! --More-- ncs/admin(config)#end
To end the current configuration session and return to EXEC mode, use the end command in configuration mode.
exit
To exit any configuration mode to the next-highest mode in the CLI mode hierarchy, use the exit command in configuration mode.
Usage Guidelines
The exit command is used in the Prime Infrastructure server to exit the current command mode to the next highest command mode in the CLI mode hierarchy.
For example, use the exit command in configuration mode to return to EXEC mode. Use the exit command in the configuration submodes to return to configuration mode. At the highest level, EXEC mode, the exit command exits the EXEC mode and disconnects from the Prime Infrastructure server (see exit, page A-24, for a description of the exit (EXEC) command).
hostname
To set the hostname of the system, use the hostname command in configuration mode. To delete the hostname from the system, use the no form of this command, which resets the system to localhost.
[no] hostname word
Syntax Description
word
Name of the host. Contains at least 2 to 64 alphanumeric characters and an underscore ( _ ). The hostname must begin with a character that is not a space.
Usage Guidelines
A single instance type of command, hostname only occurs once in the configuration of the system. The hostname must contain one argument; otherwise, an error occurs.
Examples
ncs/admin(config)# hostname ncs-1 Changing the hostname or IP may result in undesired side effects, such as installed application(s) being restarted. Are you sure you want to proceed? [y/n] y Stopping NCS Monitoring & Troubleshooting Log Processor... Stopping NCS Monitoring & Troubleshooting Log Collector... Stopping NCS Monitoring & Troubleshooting Alert Process... Stopping NCS Application Server... Stopping NCS Monitoring & Troubleshooting Session Database... Stopping NCS Database processes... Starting NCS Database processes... Starting NCS Monitoring & Troubleshooting Session Database... Starting NCS Application Server... Starting NCS Monitoring & Troubleshooting Log Collector... Starting NCS Monitoring & Troubleshooting Log Processor... Starting NCS Monitoring & Troubleshooting Alert Process... Note: NCS Processes are initializing. Use 'show application status ncs' CLI to verify all processes are in running state. ncs-1/admin(config)# ncs-1/admin# show application status ncs NCS Database listener is running, PID: 11142 NCS Database is running, number of processes: 29 NCS Application Server is still initializing. NCS M&T Session Database is running, PID: 11410 NCS M&T Log Collector is running, PID: 11532 NCS M&T Log Processor is running, PID: 11555 NCS M&T Alert Process is running, PID: 11623 ncs-1/admin#icmp echo
interface
To configure an interface type and enter interface configuration mode, use the interface command in configuration mode.
Note
VMware virtual machine may have a number of interfaces available. This depends on how many network interfaces (NIC) are added to the virtual machine.interface GigabitEthernet ip-address
Syntax Description
GigabitEthernet
Configures the Gigabit Ethernet interface.
0 - 3
Number of the Gigabit Ethernet port to configure.
NoteAfter you enter the Gigabit Ethernet port number in the interface command, you enter config-GigabitEthernet configuration submode (see the following Syntax Description).
do
EXEC command. Allows you to perform any EXEC commands in this mode (see do, page A-97 ).
end
Exits config-GigabitEthernet submode and returns you to EXEC mode.
exit
Exits the config-GigabitEthernet configuration submode.
ip
Sets IP address and netmask for the Ethernet interface (see ip address, page A-107 ).
ipv6
Configures the IPv6 autoconfiguration address and IPv6 address from DHCPv6 server. (see ipv6 address autoconfig, page A-104 and ipv6 address dhcp, page A-106 ).
no
Negates the command in this mode. Two keywords are available:
shutdown
Shuts down the interface (see shutdown, page A-119 ).
Usage Guidelines
You can use the interface command to configure subinterfaces to support various requirements.
Related Commands
Command
Description
Displays information about the system interfaces.
ip address (interface configuration mode)
Sets the IP address and netmask for the interface.
shutdown (interface configuration mode)
Shuts down the interface (see shutdown, page A-119 ).
ipv6 address autoconfig
To enable IPv6 stateless autoconfiguration, use the ipv6 address autoconfig command in configuration mode. To remove the address from the interface, use the no form of this command.
[no] ipv6 address autoconfig [default]0
Syntax Description
default
(Optional) If a default router is selected on this interface, the default keyword causes a default route to be installed using that default router.
The default keyword can be specified only on one interface.
Usage Guidelines
IPv6 stateless autoconfiguration has the security downfall of having predictable IP addresses. This downfall is resolved with privacy extensions. You can verify that the privacy extensions feature is enabled using the show command.
IPv6 address autoconfiguration is enabled by default in Linux. Cisco ADE 2.0 shows the IPv6 address autoconfiguration in the running configuration for any interface that is enabled.
Examples
Example 1
ncs/admin# configure terminal Enter configuration commands, one per line. End with CNTL/Z. ncs/admin(config)# interface GigabitEthernet 0 ncs/admin(config)# (config-GigabitEthernet)# ipv6 address autoconfig ncs/admin(config)# (config-GigabitEthernet)# end ncs/admin#When IPv6 autoconfiguration is enabled, the running configuration shows the interface settings similar to the following:
! interface GigabitEthernet 0 ip address 172.23.90.116 255.255.255.0 ipv6 address autoconfig !You can use the show interface GigabitEthernet 0 command to display the interface settings. In example 2, you can see that the interface has three IPv6 addresses. The first address (starting with 3ffe) is obtained using the stateless autoconfiguration. For the stateless autoconfiguration to work, you must have IPv6 route advertisement enabled on that subnet. The next address (starting with fe80) is a link-local address that does not have any scope outside the host. You will always see a link local address regardless of the IPv6 autoconfiguration or DHCPv6 configuration. The last address (starting with 2001) is obtained from a IPv6 DHCP server.
Example 2
ncs/admin# show interface GigabitEthernet 0 eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:DA:05 inet addr:172.23.90.116 Bcast:172.23.90.255 Mask:255.255.255.0 inet6 addr: 3ffe:302:11:2:20c:29ff:feaf:da05/64 Scope:Global inet6 addr: fe80::20c:29ff:feaf:da05/64 Scope:Link inet6 addr: 2001:558:ff10:870:8000:29ff:fe36:200/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77848 errors:0 dropped:0 overruns:0 frame:0 TX packets:23131 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10699801 (10.2 MiB) TX bytes:3448374 (3.2 MiB) Interrupt:59 Base address:0x2000 ncs/admin#To verify that the privacy extensions feature is enabled, you can use the show interface GigabitEthernet 0 command. You can see two autoconfiguration addresses: one address is without the privacy extensions, and the other is with the privacy extensions.
In the example 3 below, the MAC is 3ffe:302:11:2:20c:29ff:feaf:da05/64 and the non-RFC3041 address contains the MAC, and the privacy-extension address is 302:11:2:9d65:e608:59a9:d4b9/64.
The output appears similar to the following:
Example 3
ncs/admin# show interface GigabitEthernet 0 eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:DA:05 inet addr:172.23.90.116 Bcast:172.23.90.255 Mask:255.255.255.0 inet6 addr: 3ffe:302:11:2:9d65:e608:59a9:d4b9/64 Scope:Global inet6 addr: 3ffe:302:11:2:20c:29ff:feaf:da05/64 Scope:Global inet6 addr: fe80::20c:29ff:feaf:da05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:60606 errors:0 dropped:0 overruns:0 frame:0 TX packets:2771 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9430102 (8.9 MiB) TX bytes:466204 (455.2 KiB) Interrupt:59 Base address:0x2000 ncs/admin#Related Commands
Command
Description
Displays information about the system interfaces.
ip address (interface configuration mode)
Sets the IP address and netmask for the interface.
shutdown (interface configuration mode)
Shuts down the interface (see shutdown, page A-119 ).
Enables IPv6 address DHCP on an interface.
Displays the contents of the currently running configuration file or the configuration.
ipv6 address dhcp
To enable IPv6 address DHCP, use the ipv6 address dhcp command in configuration mode. To remove the address from the interface, use the no form of this command.
[no] ipv6 address dhcp [rapid-commit] 0
Syntax Description
[rapid-commit]
(Optional) Allows the two-message exchange method for address assignment.
0
Gigabit Ethernet port number to be configured.
Examples
ncs/admin# configure terminal Enter configuration commands, one per line. End with CNTL/Z. ncs/admin(config)# interface GigabitEthernet 0 ncs/admin(config-GigabitEthernet)# ipv6 address dhcp ncs/admin(config-GigabitEthernet)# end ncs/admin#When IPv6 DHCPv6 is enabled, the running configuration shows the interface settings similar to the following:
! interface GigabitEthernet 0 ip address 172.23.90.116 255.255.255.0 ipv6 address dhcp !
NoteThe IPv6 stateless autoconfiguration and IPv6 address DHCP are not mutually exclusive. It is possible to have both IPv6 stateless autoconfiguration and IPv6 address DHCP on the same interface. You can use the show interface to display what IPv6 addresses are in use for a particular interface.
When both the IPv6 stateless autoconfiguration and IPv6 address DHCP are enabled, the running configuration shows the interface settings similar to the following:
! interface GigabitEthernet 0 ip address 172.23.90.116 255.255.255.0 ipv6 address dhcp !Related Commands
Command
Description
Displays information about the system interfaces.
ip address (interface configuration mode)
Sets the IP address and netmask for the interface.
shutdown (interface configuration mode)
Shuts down the interface (see shutdown, page A-119 ).
Enables IPv6 stateless autoconfiguration on an interface.
Displays the contents of the currently running configuration file or the configuration.
ip address
To set the IP address and netmask for the Ethernet interface, use the ip address command in interface configuration mode. To remove an IP address or disable IP processing, use the no form of this command.
[no] ip address ip-address netmask
NoteYou can configure the same IP address on multiple interfaces. You might want to do this to limit the configuration steps that are needed to switch from using one interface to another.
Syntax Description
Examples
ncs/admin(config)# interface GigabitEthernet 1 ncs/admin(config-GigabitEthernet)# ip address 209.165.200.227 255.255.255.224 Changing the hostname or IP may result in undesired side effects, such as installed application(s) being restarted. ........ To verify that NCS processes are running, use the 'show application status ncs' command. ncs/admin(config-GigabitEthernet)#Related Commands
Command
Description
shutdown (interface configuration mode)
Disables an interface (see shutdown, page A-119 ).
Sets the IP address of the default gateway of an interface.
Displays information about the system IP interfaces.
Configures an interface type and enters the interface mode.
ip default-gateway
To define or set a default gateway with an IP address, use the ip default-gateway command in configuration mode. To disable this function, use the no form of this command.
[no] ip default-gateway ip-address
Syntax Description
Related Commands
Command
Description
ip address (interface configuration mode)
Sets the IP address and netmask for the Ethernet interface.
ip domain-name
To define a default domain name that the Prime Infrastructure server uses to complete hostnames, use the ip domain-name command in configuration mode. To disable this function, use the no form of this command.
[no] ip domain-name word
Syntax Description
ip name-server
To set the Domain Name Server (DNS) servers for use during a DNS query, use the ip name-server command in configuration mode. You can configure one to three DNS servers. To disable this function, use the no form of this command.
NoteUsing the no form of this command removes all of the name servers from the configuration. Using the no form of this command and one of the IP names removes only that IP name server.
[no] ip name-server ip-address [ip-address*]}
Syntax Description
ip-address
Address of a name server.
ip-address*
(Optional) IP addresses of additional name servers.
Note You can configure a maximum of three name servers.
Usage Guidelines
The first name server that is added with the ip name-server command occupies the first position and the system uses that server first to resolve the IP addresses.
You can add name servers to the system one at a time or all at once, until you reach the maximum (3). If you already configured the system with three name servers, you must remove at least one server to add additional name servers.
To place a name server in the first position so that the subsystem uses it first, you must remove all name servers with the no form of this command before you proceed.
Examples
ncs/admin(config)# ip name-server 209.165.201.1 To verify that NCS processes are running, use the 'show application status ncs' command. ncs/admin(config)#You can choose not to restart the Prime Infrastructure server; nevertheless, the changes will take effect.
ip route
To configure the static routes, use the ip route command in configuration mode. To remove static routes, use the no form of this command.
ip route prefix mask gateway ip-address
no ip route prefix mask
Syntax Description
prefix
IP route prefix for the destination.
mask
Prefix mask for the destination.
gateway
Route-specific gateway
ip-address
IP address of the next hop that can be used to reach that network.
Usage Guidelines
Static routes are manually configured, which makes them inflexible (they cannot dynamically adapt to network topology changes), but extremely stable. Static routes optimize bandwidth utilization, because no routing updates need to be sent to maintain them. They also make it easy to enforce routing policy.
kron occurrence
To schedule one or more Command Scheduler commands to run at a specific date and time or a recurring level, use the kron occurrence command in configuration mode. To delete this schedule, use the no form of this command.
[no] kron {occurrence} occurrence-name
Syntax Description
occurrence-name
Name of the occurrence. Up to 80 alphanumeric characters. (See the following note and Syntax Description.)
NoteAfter you enter the occurrence-name in the kron occurrence command, you enter the config-occurrence configuration submode (see the following syntax description).
at
Identifies that the occurrence is to run at a specified calendar date and time. Usage: at [hh:mm] [day-of-week | day-of-month | month day-of-month].
do
EXEC command. Allows you to perform any EXEC commands in this mode (see do, page A-97 ).
end
Exits the kron-occurrence configuration submode and returns you to EXEC mode.
exit
Exits the kron-occurrence configuration mode.
no
Negates the command in this mode.
Three keywords are available:
policy-list
Specifies a Command Scheduler policy list to be run by the occurrence.
recurring
Identifies that the occurrences run on a recurring basis.
Usage Guidelines
Use the kron occurrence and policy-list commands to schedule one or more policy lists to run at the same time or interval.
Use the kron policy-list command in conjunction with the cli command to create a Command Scheduler policy that contains the EXEC CLI commands to be scheduled to run on the Prime Infrastructure server at a specified time. See the kron policy-list, page A-113 command.
Examples
NoteWhen you run the kron command, backup bundles are created with a unique name (by adding a time stamp) to ensure that the files do not overwrite each other.
Example 1:Weekly Backup
ncs/admin(config)# kron occurrence WeeklyBackup ncs/admin(config-Occurrence)# at 14:35 Monday ncs/admin(config-Occurrence)# policy-list SchedBackupPolicy ncs/admin(config-Occurrence)# recurring ncs/admin(config-Occurrence)# exit ncs/admin(config)#Example 2: Daily Backup
ncs/admin(config)# kron occurrence DailyBackup ncs/admin(config-Occurrence)# at 02:00 ncs/admin(config-Occurrence)# exit ncs/admin(config)#kron policy-list
To specify a name for a Command Scheduler policy and enter the kron-Policy List configuration submode, use the kron policy-list command in configuration mode. To delete a Command Scheduler policy, use the no form of this command.
[no] kron {policy-list} list-name
Syntax Description
policy-list
Specifies a name for Command Scheduler policies.
list-name
Name of the policy list. Up to 80 alphanumeric characters.
NoteAfter you enter the list-name in the kron policy-list command, you enter the config-Policy List configuration submode (see the following Syntax Description).
cli
Command to be executed by the scheduler. Up to 80 alphanumeric characters.
do
EXEC command. Allows you to perform any EXEC commands in this mode (see the do, page A-97 ) command.
end
Exits from the config-policy list configuration submode and returns you to EXEC mode.
exit
Exits this submode.
no
Negates the command in this mode. One keyword is available:
Usage Guidelines
Use the kron policy-list command in conjunction with the cli command to create a Command Scheduler policy that contains the EXEC CLI commands to be scheduled to run on the Prime Infrastructure server at a specified time. Use the kron occurrence and policy list commands to schedule one or more policy lists to run at the same time or interval. See the ip route, page A-110 command.
Examples
ncs/admin(config)# kron policy-list SchedBackupMonday ncs/admin(config-Policy List)# cli backup SchedBackupMonday repository SchedBackupRepo ncs/admin(config-Policy List)# exit ncs/admin(config)#logging
To enable the system to forward logs to a remote system or to configure the log level, use the logging command in configuration mode. To disable this function, use the no form of this command.
[no] logging {ip-address | hostname} {loglevel level}
Syntax Description
ip-address
IP address of remote system to which you forward logs. Up to 32 alphanumeric characters.
hostname
Hostname of remote system to which you forward logs. Up to 32 alphanumeric characters.
loglevel
The command to configure the log level for the logging command.
level
Number of the desired priority level at which you set the log messages. Priority levels are (enter the number for the keyword):
- 0-emerg—Emergencies: System unusable.
- 1-alert—Alerts: Immediate action needed.
- 2-crit—Critical: Critical conditions.
- 3-err—Error: Error conditions.
- 4-warn—Warning: Warning conditions.
- 5-notif—Notifications: Normal but significant conditions.
- 6-inform—(Default) Informational messages.
- 7-debug—Debugging messages.
Usage Guidelines
This command requires an IP address or hostname or the loglevel keyword; an error occurs if you enter two or more of these arguments.
ntp server
To allow for software clock synchronization by the NTP server for the system, use the ntp server command in configuration mode. Allows up to three servers. To disable this capability, use the no form of this command.
[no] ntp server {ip-address | hostname} [ip-address | hostname] [ip-address | hostname]
Syntax Description
ip-address | hostname
IP address or hostname of the server providing the clock synchronization. Arguments are limited to 255 alphanumeric characters.
Usage Guidelines
Use this command if you want to allow the system to synchronize with a specified server.
To terminate NTP service on a device, you must enter the no ntp command without keywords or arguments. For example, if you previously entered the ntp server command and you now want to remove not only the server synchronization capability, but all NTP functions from the device, use the no ntp command without any keywords. This command ensures that all NTP functions are disabled and that the NTP service also terminates.
NoteThis command gives conflicting information during the sync process. The sync process can take up to 20 minutes to complete.
Examples
ncs/admin(config)# ntp server ncs ncs1 ncs2 ncs/admin(config)# ncs/admin# show ntp Primary NTP : ncs Secondary NTP : ncs1 Tertiary NTP : ncs2 synchronised to local net at stratum 11 time correct to within 11 ms polling server every 1024 s remote refid st t when poll reach delay offset jitter ============================================================================== *127.127.1.0 .LOCL. 10 l 22 64 377 0.000 0.000 0.001 172.23.90.113 .INIT. 16 u - 1024 0 0.000 0.000 0.000 172.23.90.114 .INIT. 16 u - 1024 0 0.000 0.000 0.000 172.23.90.115 .INIT. 16 u - 1024 0 0.000 0.000 0.000 Warning: Output results may conflict during periods of changing synchronization. ncs admin#password-policy
To enable or configure the passwords on the system, use the password-policy command in configuration mode. To disable this function, use the no form of this command.
[no] password-policy option
NoteThe password-policy command requires a policy option (see Syntax Description). You must enter the password-expiration-enabled command before the other password-expiration commands.
Syntax Description
NoteAfter you enter the password-policy command, you can enter config-password-policy configuration submode.
digit-required
Requires a digit in the password.
disable-repeat-characters
Disables the ability of the password to contain more than four identical characters.
disable-cisco-password
Disables the ability to use the word Cisco or any combination as the password.
do
EXEC command.
end
Exits from configure mode.
exit
Exits from this submode.
lower-case-required
Requires a lowercase letter in the password.
min-password-length
Specifies a minimum number of characters for a valid password. Integer length from 0 to 4,294,967,295.
no
Negates a command or set its defaults.
no-previous-password
Prevents users from reusing a part of their previous password.
no-username
Prohibits users from reusing their username as a part of a password.
password-expiration-days
Number of days until a password expires. Integer length from 0 to 80.
password-expiration-enabled
Enables password expiration.
Note You must enter the password-expiration-enabled command before the other password-expiration commands.
password-expiration-warning
Number of days before expiration that warnings of impending expiration begin. Integer length from 0 to 4,294,967,295.
password-lock-enabled
Locks a password after several failures.
password-lock-retry-count
Number of failed attempts before password locks. Integer length from 0 to 4,294,967,295.
upper-case-required
Requires an uppercase letter in the password.
special-required
Requires a special character in the password.
repository
To enter the repository submode for configuration of backups, use the repository command in configuration mode.
repository repository-name
Syntax Description
NoteAfter you enter the name of the repository in the repository command, you enter repository configuration submode.
do
EXEC command.
end
Exits repository config submode and returns you to EXEC mode.
exit
Exits this mode.
no
Negates the command in this mode.
Two keywords are available:
url
URL of the repository. Up to 80 alphanumeric characters (see Table A-20 ).
user
Configure the username and password for access. Up to 30 alphanumeric characters.
Table 14 URL Keywords Keyword
Source of Destination
word
Enter the repository URL, including server and path info. Up to 80 alphanumeric characters.
cdrom:
Local CD-ROM drive (read only).
disk:
Local storage.
You can enter the show repository repository_name command to view all of the files in the local repository.
Note All local repositories are created on the /localdisk partition. When you specify disk:/ in the repository URL, the system creates directories in a path that is relative to /localdisk. For example, if you entered disk:/backup, the directory is created at /localdisk/backup.
ftp:
Source or destination URL for an FTP network server. Use url ftp://server/path(1) .
nfs:
Source or destination URL for an NFS network server. Use url nfs://server:path1.
sftp:
Source or destination URL for an SFTP network server. Use url sftp://server/path1.
tftp:
Source or destination URL for a TFTP network server. Use url tftp://server/path1.
Note You cannot use a TFTP repository for performing a Prime Infrastructure upgrade.
Examples
Example 1
ncs/admin# configure termainal ncs/admin(config)# repository myrepository ncs/admin(config-Repository)# url sftp://example.com/repository/system1 ncs/admin(config-Repository)# user abcd password example ncs/admin(config-Repository)# exit ncs/admin(config)# exit ncs/admin#Example 2
ncs/admin# configure termainal ncs/admin(config)# repository myrepository ncs/admin(config-Repository)# url disk:/ ncs/admin(config-Repository)# user xyz password plain example ncs/admin(config-Repository)# exit ncs/admin(config)# exit ncs/admin#Related Commands
service
shutdown
To shut down an interface, use the shutdown command in interface configuration mode. To disable this function, use the no form of this command.
Usage Guidelines
When you shut down an interface using this command, you lose connectivity to the Cisco ISE-3315 appliance through that interface (even though the appliance is still powered on). However, if you have configured the second interface on the appliance with a different IP and have not shut down that interface, you can access the appliance through that second interface.
To shut down an interface, you can also modify the ifcfg-eth[0,1] file, which is located at /etc/sysconfig/network-scripts, using the ONBOOT parameter:
You can also use the no shutdown command to enable an interface.
Related Commands
Command
Description
Configures an interface type and enters interface mode.
ip address (interface configuration mode)
Sets the IP address and netmask for the Ethernet interface.
Displays information about the system IP interfaces.
Sets the IP address of the default gateway of an interface.
snmp-server community
To set up the community access string to permit access to the Simple Network Management Protocol (SNMP), use the snmp-server community command in configuration mode. To disable this function, use the no form of this command.
[no] snmp-server community word ro
Syntax Description
word
Accessing string that functions much like a password and allows access to SNMP. No blank spaces allowed. Up to 255 alphanumeric characters.
ro
Specifies read-only access.
Usage Guidelines
The snmp-server community command requires a community string and the ro argument; otherwise, an error occurs.
snmp-server contact
To configure the SNMP contact Management Information Base (MIB) value on the system, use the snmp-server contact command in configuration mode. To remove the system contact information, use the no form of this command.
[no] snmp-server contact word
Syntax Description
word
String that describes the system contact information of the node. Up to 255 alphanumeric characters.
snmp-server host
To send SNMP traps to a remote user, use the snmp-server host command in configuration mode. To remove trap forwarding, use the no form of this command.
[no] snmp-server host {ip-address | hostname} version {1 | 2c} community
Syntax Description
ip-address
IP address of the SNMP notification host. Up to 32 alphanumeric characters.
hostname
Name of the SNMP notification host. Up to 32 alphanumeric characters.
version {1 | 2c}
(Optional) Version of the SNMP used to send the traps. Default = 1.
If you use the version keyword, specify one of the following keywords:
community
Password-like community string that is sent with the notification operation.
Examples
ncs/admin(config)# snmp-server community new ro ncs/admin(config)# snmp-server host 209.165.202.129 version 1 password ncs/admin(config)#snmp-server location
To configure the SNMP location MIB value on the system, use the snmp-server location command in configuration mode. To remove the system location information, use the no form of this command.
[no] snmp-server location word
Syntax Description
word
String that describes the physical location information of the system. Up to 255 alphanumeric characters.
Usage Guidelines
We recommend that you use underscores (_) or hyphens (-) between the terms within the word string. If you use spaces between terms within the word string, you must enclose the string in quotation marks (“).
Examples
Example 1
ncs/admin(config)# snmp-server location Building_3/Room_214 ncs/admin(config)#Example 2
ncs/admin(config)# snmp-server location “Building 3/Room 214” ncs/admin(config)#username
To add a user who can access the Cisco ISE-3315 using SSH, use the username command in configuration mode. If the user already exists, the password, the privilege level, or both change with this command. To delete the user from the system, use the no form of this command.
[no] username username password {hash | plain} password role {admin | user] [disabled [email email-address]] [email email-address]
For an existing user, use the following command option:
username username password role {admin | user} password
Syntax Description
username
You should enter only one word which can include hyphen (-), underscore (_) and period (.).
Note Only alphanumeric characters are allowed at an initial setup. password
The command to use specify password and user role.
password
Password character length up to 40 alphanumeric characters. You must specify the password for all new users.
hash | plain
Type of password. Up to 34 alphanumeric characters.
role admin | user
Sets the privilege level for the user.
disabled
Disables the user according to the user’s email address.
email email-address
The user’s email address. For example, user1@example.com.
Usage Guidelines
The username command requires that the username and password keywords precede the hash | plain and the admin | user options.
Examples
Example 1ncs/admin(config)# username admin password hash ###### role admin ncs/admin(config)#Example 2ncs/admin(config)# username admin password plain Secr3tp@swd role admin ncs/admin(config)#Example 3ncs/admin(config)# username admin password plain Secr3tp@swd role admin email admin123@example.com ncs/admin(config)#
