-
Cisco Wireless LAN Controller Command Reference, Release 7.5
-
Preface
-
Using the Command-Line Interface
- System Management Commands
- Ports and Interfaces Commands
- VideoStream Commands
- Security Commands
- WLAN Commands
- Lightweight Access Point Commands
- Mesh Access Point Commands
- Radio Resource Management Commands
- CleanAir Commands
- FlexConnect Commands
- Mobility Commands
-
Index
-
Feedback
Contents
CLI Commands
The Cisco Wireless LAN solution command-line interface (CLI) enables operators to connect an ASCII console to the Cisco Wireless LAN Controller and configure the controller and its associated access points.
- show Commands
- capwap ap Commands
- config Commands
- clear Commands
- debug Commands
- transfer download peer-start
- transfer upload peer-start
- Resetting the System Reboot Time
- test Commands
show Commands
This section lists the show commands to display information about your configuration settings for access points.
- show advanced backup-controller
- show advanced max-1x-sessions
- show advanced probe
- show advanced rate
- show advanced timers
- show ap auto-rf
- show ap ccx rm
- show ap cdp
- show ap channel
- show ap config
- show ap config global
- show ap core-dump
- show ap crash-file
- show ap data-plane
- show ap ethernet tag
- show ap eventlog
- show ap image
- show ap inventory
- show ap join stats detailed
- show ap join stats summary
- show ap join stats summary all
- show ap led-state
- show ap led-flash
- show ap link-encryption
- show ap max-count summary
- show ap monitor-mode summary
- show ap packet-dump status
- show ap retransmit
- show ap stats
- show ap summary
- show ap tcp-mss-adjust
- show ap wlan
- show auth-list
- show client ap
- show boot
- show call-control ap
- show country
- show country channels
- show country supported
- show dtls connections
- show known ap
- show ipv6 ra-guard
- show msglog
- show network summary
- show redundancy summary
- show redundancy latency
- show redundancy interfaces
- show redundancy mobilitymac
- show redundancy peer-route summary
- show redundancy statistics
- show redundancy timers
- show watchlist
show advanced backup-controller
show advanced max-1x-sessions
show advanced probe
show advanced rate
show advanced timers
To display the mobility anchor, authentication response, and rogue access point entry timers, use the show advanced timers command.
Command History
Examples
The following example shows how to display the system timers setting:
> show advanced timers Authentication Response Timeout (seconds)........ 10 Rogue Entry Timeout (seconds).................... 1200 AP Heart Beat Timeout (seconds).................. 30 AP Discovery Timeout (seconds)................... 10 AP Local mode Fast Heartbeat (seconds)........... disable AP flexconnect mode Fast Heartbeat (seconds)........... disable AP Primary Discovery Timeout (seconds)........... 120show ap auto-rf
To display the auto-RF settings for a Cisco lightweight access point, use the show ap auto-rf command.
Syntax Description
Command History
Examples
The following example shows how to display auto-RF information for an access point:
(Cisco Controller) > show ap auto-rf 802.11a AP1 Number Of Slots.................................. 2 AP Name.......................................... AP03 MAC Address...................................... 00:0b:85:01:18:b7 Radio Type..................................... RADIO_TYPE_80211a Noise Information Noise Profile................................ PASSED Channel 36................................... -88 dBm Channel 40................................... -86 dBm Channel 44................................... -87 dBm Channel 48................................... -85 dBm Channel 52................................... -84 dBm Channel 56................................... -83 dBm Channel 60................................... -84 dBm Channel 64................................... -85 dBm Interference Information Interference Profile......................... PASSED Channel 36................................... -66 dBm @ 1% busy Channel 40................................... -128 dBm @ 0% busy Channel 44................................... -128 dBm @ 0% busy Channel 48................................... -128 dBm @ 0% busy Channel 52................................... -128 dBm @ 0% busy Channel 56................................... -73 dBm @ 1% busy Channel 60................................... -55 dBm @ 1% busy Channel 64................................... -69 dBm @ 1% busy Rogue Histogram (20/40_ABOVE/40_BELOW) Channel 36................................... 16/ 0/ 0 Channel 40................................... 28/ 0/ 0 Channel 44................................... 9/ 0/ 0 Channel 48................................... 9/ 0/ 0 Channel 52................................... 3/ 0/ 0 Channel 56................................... 4/ 0/ 0 Channel 60................................... 7/ 1/ 0 Channel 64................................... 2/ 0/ 0 Load Information Load Profile................................. PASSED Receive Utilization.......................... 0% Transmit Utilization......................... 0% Channel Utilization.......................... 1% Attached Clients............................. 1 clients Coverage Information Coverage Profile............................. PASSED Failed Clients............................... 0 clients Client Signal Strengths RSSI -100 dBm................................ 0 clients RSSI -92 dBm................................ 0 clients RSSI -84 dBm................................ 0 clients RSSI -76 dBm................................ 0 clients RSSI -68 dBm................................ 0 clients RSSI -60 dBm................................ 0 clients RSSI -52 dBm................................ 0 clients Client Signal To Noise Ratios SNR 0 dBm................................. 0 clients SNR 5 dBm................................. 0 clients SNR 10 dBm................................. 0 clients SNR 15 dBm................................. 0 clients SNR 20 dBm................................. 0 clients SNR 25 dBm................................. 0 clients SNR 30 dBm................................. 0 clients SNR 35 dBm................................. 0 clients SNR 40 dBm................................. 0 clients SNR 45 dBm................................. 0 clients Nearby RADs RAD 00:0b:85:01:05:08 slot 0................. -46 dBm on 10.1.30.170 RAD 00:0b:85:01:12:65 slot 0................. -24 dBm on 10.1.30.170 Channel Assignment Information Current Channel Average Energy............... -86 dBm Previous Channel Average Energy.............. -75 dBm Channel Change Count......................... 109 Last Channel Change Time..................... Wed Sep 29 12:53e:34 2004 Recommended Best Channel..................... 44 RF Parameter Recommendations Power Level.................................. 1 RTS/CTS Threshold............................ 2347 Fragmentation Threshold...................... 2346 Antenna Pattern.............................. 0show ap ccx rm
To display an access point’s Cisco Client eXtensions (CCX) radio management status information, use the show ap ccx rm command.
Syntax Description
Command History
Examples
The following example shows how to display the status of the CCX radio management:
> show ap ccx rm AP1240-21ac status A Radio Channel Load Request ..................... Disabled Noise Histogram Request .................. Disabled Beacon Request ........................... Disabled Frame Request ............................ Disabled Interval ................................. 60 Iteration ................................ 10 G Radio Channel Load Request ..................... Disabled Noise Histogram Request .................. Disabled Beacon Request ........................... Disabled Frame Request ............................ Disabled Interval ................................. 60 Iteration ................................ 10show ap cdp
To display the Cisco Discovery Protocol (CDP) information for an access point, use the show ap cdp command.
Syntax Description
cisco_ap
Specified access point name.
Displays details about a specific access point neighbor using CDP.
Command History
Examples
The following example shows how to display the CDP status of all access points:
> show ap cdp all AP CDP State AP Name AP CDP State ------------------ ---------- SB_RAP1 enable SB_MAP1 enable SB_MAP2 enable SB_MAP3 enableThe following example shows how to display the CDP status of a specified access point:
> show ap cdp ap-name SB_RAP1 AP CDP State AP Name AP CDP State ------------------ ---------- AP CDP State.......................Enabled AP Interface-Based CDP state Ethernet 0.....................Enabled Slot 0.........................Enabled Slot 1.........................EnabledThe following example shows how to display details about all neighbors using CDP:
> show ap cdp neighbor all AP Name AP IP Neighbor Name Neighbor IP Neighbor Port --------- --------------- ------------------ -------------- ------------- SB_RAP1 192.168.102.154 sjc14-41a-sw1 192.168.102.2 GigabitEthernet1/0/13 SB_RAP1 192.168.102.154 SB_MAP1 192.168.102.137 Virtual-Dot11Radio0 SB_MAP1 192.168.102.137 SB_RAP1 192.168.102.154 Virtual-Dot11Radio0 SB_MAP1 192.168.102.137 SB_MAP2 192.168.102.138 Virtual-Dot11Radio0 SB_MAP2 192.168.102.138 SB_MAP1 192.168.102.137 Virtual-Dot11Radio1 SB_MAP2 192.168.102.138 SB_MAP3 192.168.102.139 Virtual-Dot11Radio0 SB_MAP3 192.168.102.139 SB_MAP2 192.168.102.138 Virtual-Dot11Radio1The following example shows how to display details about a specific neighbor with a specified access point using CDP:
> show ap cdp neighbors ap-name SB_MAP2 AP Name AP IP Neighbor Name Neighbor IP Neighbor Port ----------- --------------- --------------- -------------- ------------- SB_MAP2 192.168.102.138 SB_MAP1 192.168.102.137 Virtual-Dot11Radio1 SB_MAP2 192.168.102.138 SB_MAP3 192.168.102.139 Virtual-Dot11Radio0The following example shows how to display details about neighbors using CDP:
> show ap cdp neighbors detail SB_MAP2 AP Name:SB_MAP2 AP IP address:192.168.102.138 ------------------------- Device ID: SB_MAP1 Entry address(es): 192.168.102.137 Platform: cisco AIR-LAP1522AG-A-K9 , Cap Interface: Virtual-Dot11Radio0, Port ID (outgoing port): Virtual-Dot11Radio1 Holdtime : 180 sec Version : Cisco IOS Software, C1520 Software (C1520-K9W8-M), Experimental Version 12.4(200 81114:084420) [BLD-v124_18a_ja_throttle.20081114 208] Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Fri 14-Nov-08 23:08 by advertisement version: 2 ------------------------- Device ID: SB_MAP3 Entry address(es): 192.168.102.139 Platform: cisco AIR-LAP1522AG-A-K9 , Capabilities: Trans-Bridge Interface: Virtual-Dot11Radio1, Port ID (outgoing port): Virtual-Dot11Radio0 Holdtime : 180 sec Version : Cisco IOS Software, C1520 Software (C1520-K9W8-M), Experimental Version 12.4(200 81114:084420) [BLD-v124_18a_ja_throttle.20081114 208] Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Fri 14-Nov-08 23:08 by advertisement version: 2show ap channel
To display the available channels for a specific mesh access point, use the show ap channel command.
Syntax Description
Command History
Examples
The following example shows how to display the available channels for a particular access point:
> show ap channel AP47 802.11b/g Current Channel ...........1 Allowed Channel List.....................1,2,3,4,5,6,7,8,9,10,11 802.11a Current Channel .................161 Allowed Channel List.....................36,40,44,48,52,56,60,64,100, .........................................104,108,112,116,132,136,140, .........................................149,153,157,161show ap config
To display the detailed configuration for a lightweight access point, use the show ap config command.
Syntax Description
Command History
Examples
The following example shows how to display the detailed configuration for an access point:
> show ap config 802.11a AP02 Cisco AP Identifier.............................. 0 Cisco AP Name.................................... AP02 Country code..................................... US - United States Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A AP Regulatory Domain............................. Unconfigured Switch Port Number .............................. 1 MAC Address...................................... 00:0b:85:18:b6:50 IP Address Configuration......................... DHCP IP Address....................................... 1.100.49.240 IP NetMask....................................... 255.255.255.0 Gateway IP Addr.................................. 1.100.49.1 CAPWAP Path MTU.................................. 1485 Telnet State..................................... Disabled Ssh State........................................ Disabled Cisco AP Location................................ default-location Cisco AP Group Name.............................. default-group Primary Cisco Switch............................. Cisco_32:ab:63 Primary Cisco Switch IP Address.................. Not Configured Secondary Cisco Switch........................... Secondary Cisco Switch IP Address................ Not Configured Tertiary Cisco Switch............................ Tertiary Cisco Switch IP Address................. Not Configured Administrative State ............................ ADMIN_ENABLED Operation State ................................. REGISTERED Mirroring Mode .................................. Disabled AP Mode ........................................... Sniffer Public Safety ..................................... Global: Disabled, Local: Disabled AP SubMode ...................................... Not Configured Remote AP Debug ................................. Disabled Logging trap severity level ..................... informational Logging syslog facility ......................... kern S/W Version .................................... 7.0.110.6 Boot Version ................................... 12.4.18.0 Mini IOS Version ................................ 3.0.51.0 Stats Reporting Period .......................... 180 Stats Re--More-- or (q)uit LED State........................................ Enabled PoE Pre-Standard Switch.......................... Enabled PoE Power Injector MAC Addr...................... Disabled Power Type/Mode.................................. Power injector / Normal mode Number Of Slots.................................. 2 AP Model......................................... AIR-LAP1142N-A-K9 AP Image......................................... C1140-K9W8-M IOS Version...................................... 12.4(20100502:031212) Reset Button..................................... Enabled AP Serial Number................................. FTX1305S180 AP Certificate Type.............................. Manufacture Installed AP User Mode..................................... AUTOMATIC AP User Name..................................... Not Configured AP Dot1x User Mode............................... Not Configured AP Dot1x User Name............................... Not Configured Cisco AP system logging host..................... 255.255.255.255 AP Up Time....................................... 47 days, 23 h 47 m 47 s AP LWAPP Up Time................................. 47 days, 23 h 10 m 37 s Join Date and Time............................... Tue May 4 16:05:00 2010 Join Taken Time.................................. 0 days, 00 h 01 m 37 s Attributes for Slot 1 Radio Type................................... RADIO_TYPE_80211n-5 Radio Subband................................ RADIO_SUBBAND_ALL Administrative State ........................ ADMIN_ENABLED Operation State ............................. UP Radio Role .................................. ACCESS CellId ...................................... 0 Station Configuration Configuration ............................. AUTOMATIC Number Of WLANs ........................... 2 Medium Occupancy Limit .................... 100 CFP Period ................................ 4 CFP MaxDuration ........................... 60 BSSID ..................................... 00:24:97:88:99:60 Operation Rate Set 6000 Kilo Bits........................... MANDATORY 9000 Kilo Bits........................... SUPPORTED 12000 Kilo Bits.......................... MANDATORY 18000 Kilo Bits.......................... SUPPORTED 24000 Kilo Bits.......................... MANDATORY 36000 Kilo Bits.......................... SUPPORTED 48000 Kilo Bits.......................... SUPPORTED 54000 Kilo Bits.......................... SUPPORTED MCS Set MCS 0.................................... SUPPORTED MCS 1.................................... SUPPORTED MCS 2.................................... SUPPORTED MCS 3.................................... SUPPORTED MCS 4.................................... SUPPORTED MCS 5.................................... SUPPORTED MCS 6.................................... SUPPORTED MCS 7.................................... SUPPORTED MCS 8.................................... SUPPORTED MCS 9.................................... SUPPORTED MCS 10................................... SUPPORTED MCS 11................................... SUPPORTED MCS 12................................... SUPPORTED MCS 13................................... SUPPORTED MCS 14................................... SUPPORTED MCS 15................................... SUPPORTED Beacon Period ............................. 100 Fragmentation Threshold ................... 2346 Multi Domain Capability Implemented ....... TRUE Multi Domain Capability Enabled ........... TRUE Country String ............................ US Multi Domain Capability Configuration ............................. AUTOMATIC First Chan Num ............................ 36 Number Of Channels ........................ 21 MAC Operation Parameters Configuration ............................. AUTOMATIC Fragmentation Threshold ................... 2346 Packet Retry Limit ........................ 64 Tx Power Num Of Supported Power Levels ............. 6 Tx Power Level 1 .......................... 14 dBm Tx Power Level 2 .......................... 11 dBm Tx Power Level 3 .......................... 8 dBm Tx Power Level 4 .......................... 5 dBm Tx Power Level 5 .......................... 2 dBm Tx Power Level 6 .......................... -1 dBm Tx Power Configuration .................... AUTOMATIC Current Tx Power Level .................... 0 Phy OFDM parameters Configuration ............................. AUTOMATIC Current Channel ........................... 36 Extension Channel ......................... NONE Channel Width.............................. 20 Mhz Allowed Channel List....................... 36,40,44,48,52,56,60,64,100, ......................................... 104,108,112,116,132,136,140, ......................................... 149,153,157,161,165 TI Threshold .............................. -50 Legacy Tx Beamforming Configuration ....... AUTOMATIC Legacy Tx Beamforming ..................... DISABLED Antenna Type............................... INTERNAL_ANTENNA Internal Antenna Gain (in .5 dBi units).... 6 Diversity.................................. DIVERSITY_ENABLED 802.11n Antennas Tx A....................................... ENABLED B....................................... ENABLED Rx A....................................... ENABLED B....................................... ENABLED C....................................... ENABLED Performance Profile Parameters Configuration ............................. AUTOMATIC Interference threshold..................... 10 % Noise threshold............................ -70 dBm RF utilization threshold................... 80 % Data-rate threshold........................ 1000000 bps Client threshold........................... 12 clients Coverage SNR threshold..................... 16 dB Coverage exception level................... 25 % Client minimum exception level............. 3 clients Rogue Containment Information Containment Count............................ 0 CleanAir Management Information CleanAir Capable......................... No Radio Extended Configurations: Buffer size ……………………….30 Data-rate…………………………..0 Beacon strt ………………………..90 ms Rx-Sensitivity SOP threshold ………….. -80 dB CCA threshold ……………………. -60 dBThe following example shows how to display the detailed configuration for another access point:
> show ap config 802.11b AP02 Cisco AP Identifier.............................. 0 Cisco AP Name.................................... AP02 AP Regulatory Domain............................. Unconfigured Switch Port Number .............................. 1 MAC Address...................................... 00:0b:85:18:b6:50 IP Address Configuration......................... DHCP IP Address....................................... 1.100.49.240 IP NetMask....................................... 255.255.255.0 Gateway IP Addr.................................. 1.100.49.1 Cisco AP Location................................ default-location Cisco AP Group Name.............................. default-group Primary Cisco Switch............................. Cisco_32:ab:63 Secondary Cisco Switch........................... Tertiary Cisco Switch............................ Administrative State ............................ ADMIN_ENABLED Operation State ................................. REGISTERED Mirroring Mode .................................. Disabled AP Mode ......................................... Local Remote AP Debug ................................. Disabled S/W Version .................................... 3.1.61.0 Boot Version ................................... 1.2.59.6 Stats Reporting Period .......................... 180 LED State........................................ Enabled ILP Pre Standard Switch.......................... Disabled ILP Power Injector............................... Disabled Number Of Slots.................................. 2 AP Model......................................... AS-1200 AP Serial Number................................. 044110223A AP Certificate Type.............................. Manufacture Installed Attributes for Slot 1 Radio Type................................... RADIO_TYPE_80211g Administrative State ........................ ADMIN_ENABLED Operation State ............................. UP CellId ...................................... 0 Station Configuration Configuration ............................. AUTOMATIC Number Of WLANs ........................... 1 Medium Occupancy Limit .................... 100 CFP Period ................................ 4 CFP MaxDuration ........................... 60 BSSID ..................................... 00:0b:85:18:b6:50 Operation Rate Set 1000 Kilo Bits........................... MANDATORY 2000 Kilo Bits........................... MANDATORY 5500 Kilo Bits........................... MANDATORY 11000 Kilo Bits.......................... MANDATORY 6000 Kilo Bits........................... SUPPORTED 9000 Kilo Bits........................... SUPPORTED 12000 Kilo Bits.......................... SUPPORTED 18000 Kilo Bits.......................... SUPPORTED 24000 Kilo Bits.......................... SUPPORTED 36000 Kilo Bits.......................... SUPPORTED 48000 Kilo Bits.......................... SUPPORTED 54000 Kilo Bits.......................... SUPPORTED Beacon Period ............................. 100 DTIM Period ............................... 1 Fragmentation Threshold ................... 2346 Multi Domain Capability Implemented ....... TRUE Multi Domain Capability Enabled ........... TRUE Country String ............................ US Multi Domain Capability Configuration ............................. AUTOMATIC First Chan Num ............................ 1 Number Of Channels ........................ 11 MAC Operation Parameters Configuration ............................. AUTOMATIC RTS Threshold ............................. 2347 Short Retry Limit ......................... 7 Long Retry Limit .......................... 4 Fragmentation Threshold ................... 2346 Maximum Tx MSDU Life Time ................. 512 Maximum Rx Life Time....................... 512 Tx Power Num Of Supported Power Levels.............. 5 Tx Power Level 1 .......................... 17 dBm Tx Power Level 2........................... 14 dBm Tx Power Level 3........................... 11 dBm Tx Power Level 4........................... 8 dBm Tx Power Level 5........................... 5 dBm Tx Power Configuration..................... CUSTOMIZED Current Tx Power Level..................... 5 Phy OFDM parameters Configuration.............................. CUSTOMIZED Current Channel............................ 1 TI Threshold............................... -50 Legacy Tx Beamforming Configuration ....... CUSTOMIZED Legacy Tx Beamforming ..................... ENABLED Antenna Type............................... INTERNAL_ANTENNA Internal Antenna Gain (in5 dBm units)...... 11 Diversity.................................. DIVERSITY_ENABLED Performance Profile Parameters Configuration.............................. AUTOMATIC Interference threshold..................... 10% Noise threshold............................ -70 dBm RF utilization threshold................... 80% Data-rate threshold........................ 1000000 bps Client threshold........................... 12 clients Coverage SNR threshold..................... 12 dB Coverage exception level................... 25% Client minimum exception level............. 3 clients Rogue Containment Information Containment Count............................ 0The following example shows how to display the general configuration of a Cisco access point:
> show ap config general cisco-ap Cisco AP Identifier.............................. 9 Cisco AP Name.................................... cisco-ap Country code..................................... US - United States Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A AP Country code.................................. US - United States AP Regulatory Domain............................. 802.11bg:-A 802.11a:-A Switch Port Number .............................. 1 MAC Address...................................... 12:12:12:12:12:12 IP Address Configuration......................... DHCP IP Address....................................... 10.10.10.21 IP NetMask....................................... 255.255.255.0 CAPWAP Path MTU.................................. 1485 Domain........................................... Name Server...................................... Telnet State..................................... Disabled Ssh State........................................ Disabled Cisco AP Location................................ default location Cisco AP Group Name.............................. default-group Primary Cisco Switch Name........................ 4404 Primary Cisco Switch IP Address.................. 10.10.10.32 Secondary Cisco Switch Name...................... Secondary Cisco Switch IP Address................ Not Configured Tertiary Cisco Switch Name....................... 4404 Tertiary Cisco Switch IP Address................. 3.3.3.3 Administrative State ............................ ADMIN_ENABLED Operation State ................................. REGISTERED Mirroring Mode .................................. Disabled AP Mode ......................................... Local Public Safety ................................... Global: Disabled, Local: Disabled AP subMode ...................................... WIPS Remote AP Debug ................................. Disabled S/W Version .................................... 5.1.0.0 Boot Version ................................... 12.4.10.0 Mini IOS Version ................................ 0.0.0.0 Stats Reporting Period .......................... 180 LED State........................................ Enabled PoE Pre-Standard Switch.......................... Enabled PoE Power Injector MAC Addr...................... Disabled Power Type/Mode.................................. PoE/Low Power (degraded mode) Number Of Slots.................................. 2 AP Model......................................... AIR-LAP1252AG-A-K9 IOS Version...................................... 12.4(10:0) Reset Button..................................... Enabled AP Serial Number................................. serial_number AP Certificate Type.............................. Manufacture Installed Management Frame Protection Validation........... Enabled (Global MFP Disabled) AP User Mode..................................... CUSTOMIZED AP username..................................... maria AP Dot1x User Mode............................... Not Configured AP Dot1x username............................... Not Configured Cisco AP system logging host..................... 255.255.255.255 AP Up Time....................................... 4 days, 06 h 17 m 22 s AP LWAPP Up Time................................. 4 days, 06 h 15 m 00 s Join Date and Time............................... Mon Mar 3 06:19:47 2008 Ethernet Port Duplex............................. Auto Ethernet Port Speed.............................. Auto AP Link Latency.................................. Enabled Current Delay................................... 0 ms Maximum Delay................................... 240 ms Minimum Delay................................... 0 ms Last updated (based on AP Up Time).............. 4 days, 06 h 17 m 20 s Rogue Detection.................................. Enabled AP TCP MSS Adjust................................ Disabled Mesh preferred parent............................ 00:24:13:0f:92:00show ap config global
show ap core-dump
show ap crash-file
show ap data-plane
To display the data plane status for all access points or a specific access point, use the show ap data-plane command.
Syntax Description
Command History
Examples
The following example shows how to display the data plane status of all access points:
> show ap data-plane all Min Data Data Max Data Last AP Name Round Trip Round Trip Round Trip Update ------------------ -------------- -------------- -------------- ------ 1130 0.000s 0.000s 0.002s 18:51:23 1240 0.000s 0.000s 0.000s 18:50:45show ap ethernet tag
To display the VLAN tagging information of an Ethernet interface, use the show ap ethernet tag command.
Syntax Description
summary Displays the VLAN tagging information for all access points associated to the controller.
cisco_ap Name of the Cisco lightweight access point. Displays the VLAN tagging information for a specific access point associated to the controller.
Command History
Usage Guidelines
If the access point is unable to route traffic or reach the controller using the specified trunk VLAN, it falls back to the untagged configuration. If the access point joins the controller using this fallback configuration, the controller sends a trap to a trap server such as the WCS, which indicates the failure of the trunk VLAN. In this scenario, the "Failover to untagged" message appears in show command output.
show ap eventlog
To display the contents of the event log file for an access point that is joined to the controller, use the show ap eventlog command.
Syntax Description
Command History
Examples
The following example shows how to display the event log of an access point:
> show ap eventlog ciscoAP AP event log download has been initiated Waiting for download to complete AP event log download completed. ======================= AP Event log Contents ===================== *Feb 13 11:54:17.146: %CAPWAP-3-CLIENTEVENTLOG: AP event log has been cleared from the contoller 'admin' *Feb 13 11:54:32.874: *** Access point reloading. Reason: Reload Command *** *Mar 1 00:00:39.134: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source *Mar 1 00:00:39.174: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up *Mar 1 00:00:39.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up *Mar 1 00:00:49.947: %CAPWAP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP. ...show ap image
To display the detailed information about the predownloaded image for specified access points, use the show ap image command.
Syntax Description
Note
If you have an AP that has the name all, it conflicts with the keyword all that specifies all access points. In this scenario, the keyword all takes precedence over the AP that is named all.
Command History
show ap join stats detailed
To display all join-related statistics collected for a specific access point, use the show ap join stats detailed command.
Syntax Description
Command History
Examples
The following example shows how to display join information for a specific access point trying to join the controller:
> show ap join stats detailed 00:0b:85:02:0d:20 Discovery phase statistics - Discovery requests received.......................... 2 - Successful discovery responses sent.................. 2 - Unsuccessful discovery request processing............ 0 - Reason for last unsuccessful discovery attempt....... Not applicable - Time at last successful discovery attempt............ Aug 21 12:50:23:335 - Time at last unsuccessful discovery attempt.......... Not applicable Join phase statistics - Join requests received............................... 1 - Successful join responses sent....................... 1 - Unsuccessful join request processing................. 1 - Reason for last unsuccessful join attempt.............RADIUS authorization is pending for the AP - Time at last successful join attempt................. Aug 21 12:50:34:481 - Time at last unsuccessful join attempt............... Aug 21 12:50:34:374 Configuration phase statistics - Configuration requests received...................... 1 - Successful configuration responses sent.............. 1 - Unsuccessful configuration request processing........ 0 - Reason for last unsuccessful configuration attempt... Not applicable - Time at last successful configuration attempt........ Aug 21 12:50:34:374 - Time at last unsuccessful configuration attempt...... Not applicable Last AP message decryption failure details - Reason for last message decryption failure........... Not applicable Last AP disconnect details - Reason for last AP connection failure................ Not applicable Last join error summary - Type of error that occurred last..................... Lwapp join request rejected - Reason for error that occurred last.................. RADIUS authorization is pending for the AP - Time at which the last join error occurred........... Aug 21 12:50:34:374show ap join stats summary
To display the last join error detail for a specific access point, use the show ap join stats summary command.
Syntax Description
Command History
Usage Guidelines
To obtain the MAC address of the 802.11 radio interface, enter the show interface command on the access point.
Examples
The following example shows how to display specific join information for an access point:
> show ap join stats summary 00:0b:85:02:0d:20 Is the AP currently connected to controller.......................... No Time at which the AP joined this controller last time................ Aug 21 12:50:36:061 Type of error that occurred last..................................... Lwapp join request rejected Reason for error that occurred last.................................. RADIUS authorization is pending for the AP Time at which the last join error occurred........................... Aug 21 12:50:34:374show ap join stats summary all
To display the MAC addresses of all the access points that are joined to the controller or that have tried to join, use the show ap join stats summary all command.
Command History
Examples
The following example shows how to display a summary of join information for all access points:
> show ap join stats summary all Number of APs.............................................. 4 Base Mac AP EthernetMac AP Name IP Address Status 00:0b:85:57:bc:c0 00:0b:85:57:bc:c0 AP1130 10.10.163.217 Joined 00:1c:0f:81:db:80 00:1c:63:23:ac:a0 AP1140 10.10.163.216 Not joined 00:1c:0f:81:fc:20 00:1b:d5:9f:7d:b2 AP1 10.10.163.215 Joined 00:21:1b:ea:36:60 00:0c:d4:8a:6b:c1 AP2 10.10.163.214 Not joinedshow ap led-state
show ap link-encryption
show ap max-count summary
show ap monitor-mode summary
show ap packet-dump status
Command History
Usage Guidelines
Packet Capture does not work during intercontroller roaming.
The controller does not capture packets created in the radio firmware and sent out of the access point, such as the beacon or probe response. Only packets that flow through the Radio driver in the Tx path are captured.
Examples
The following example shows how to display the access point Packet Capture configurations:
> show ap packet-dump status Packet Capture Status............................ Stopped FTP Server IP Address............................ 0.0.0.0 FTP Server Path.................................. FTP Server Username.............................. FTP Server Password.............................. ******** Buffer Size for Capture.......................... 2048 KB Packet Capture Time.............................. 45 Minutes Packet Truncate Length........................... Unspecified Packet Capture Classifier........................ Noneshow ap retransmit
To display access point control packet retransmission parameters, use theshow ap retransmit command.
Syntax Description
Command History
Examples
The following example shows how to display the control packet retransmission parameters of all access points on a network:
> show ap retransmit all Global control packet retransmit interval: 3 (default) Global control packet retransmit count: 5 (default) AP Name Retransmit Interval Retransmit count ------------------ ------------------- ------------------- AP_004 3 (default) 5 (WLC default),5 (AP default)show ap stats
Syntax Description
ethernet
Specifies AP ethernet interface statistics.
summary
Displays ethernet interface summary of all the connected Cisco access points.
Command History
Examples
The following example shows how to display statistics of an access point for the 802.11b network:
> show ap stats 802.11a Ibiza Number Of Slots.................................. 2 AP Name.......................................... Ibiza MAC Address...................................... 44:2b:03:9a:8a:73 Radio Type....................................... RADIO_TYPE_80211a Stats Information Number of Users................................ 0 TxFragmentCount................................ 84628 MulticastTxFrameCnt............................ 84628 FailedCount.................................... 0 RetryCount..................................... 0 MultipleRetryCount............................. 0 FrameDuplicateCount............................ 0 RtsSuccessCount................................ 1 RtsFailureCount................................ 0 AckFailureCount................................ 0 RxIncompleteFragment........................... 0 MulticastRxFrameCnt............................ 0 FcsErrorCount.................................. 20348857 TxFrameCount................................... 84628 WepUndecryptableCount.......................... 19907 TxFramesDropped................................ 0 Rate Limiting Stats: Wlan 1: Number of Data Packets Received.............. 592 Number of Data Rx Packets Dropped............ 160 Number of Data Bytes Received................ 160783 Number of Data Rx Bytes Dropped.............. 0 Number of Realtime Packets Received.......... 592 Number of Realtime Rx Packets Dropped........ 0 Number of Realtime Bytes Received............ 160783 Number of Realtime Rx Bytes Dropped.......... 0 Number of Data Packets Sent.................. 131 Number of Data Tx Packets Dropped............ 0 Number of Data Bytes Sent.................... 23436 Number of Data Tx Bytes Dropped.............. 0 Number of Realtime Packets Sent.............. 131 Number of Realtime Tx Packets Dropped........ 0 Number of Realtime Bytes Sent................ 23436 Number of Realtime Tx Bytes Dropped.......... 0 Call Admission Control (CAC) Stats Voice Bandwidth in use(% of config bw)......... 0 Voice Roam Bandwidth in use(% of config bw).... 0 Total channel MT free........................ 0 Total voice MT free.......................... 0 Na Direct.................................... 0 Na Roam...................................... 0 Video Bandwidth in use(% of config bw)......... 0 Video Roam Bandwidth in use(% of config bw).... 0 Total BW in use for Voice(%)................... 0 Total BW in use for SIP Preferred call(%)...... 0 WMM TSPEC CAC Call Stats Total num of voice calls in progress........... 0 Num of roaming voice calls in progress......... 0 Total Num of voice calls since AP joined....... 0 Total Num of roaming calls since AP joined..... 0 Total Num of exp bw requests received.......... 0 Total Num of exp bw requests admitted.......... 0 Num of voice calls rejected since AP joined.... 0 Num of roam calls rejected since AP joined..... 0 Num of calls rejected due to insufficent bw.... 0 Num of calls rejected due to invalid params.... 0 Num of calls rejected due to PHY rate.......... 0 Num of calls rejected due to QoS policy........ 0 SIP CAC Call Stats Total Num of calls in progress................. 0 Num of roaming calls in progress............... 0 Total Num of calls since AP joined............. 0 Total Num of roaming calls since AP joined..... 0 Total Num of Preferred calls received.......... 0 Total Num of Preferred calls accepted.......... 0 Total Num of ongoing Preferred calls........... 0 Total Num of calls rejected(Insuff BW)......... 0 Total Num of roam calls rejected(Insuff BW).... 0 WMM Video TSPEC CAC Call Stats Total num of video calls in progress........... 0 Num of roaming video calls in progress......... 0 Total Num of video calls since AP joined....... 0 Total Num of video roaming calls since AP j.... 0 Num of video calls rejected since AP joined.... 0 Num of video roam calls rejected since AP j.... 0 Num of video calls rejected due to insuffic.... 0 Num of video calls rejected due to invalid .... 0 Num of video calls rejected due to PHY rate.... 0 Num of video calls rejected due to QoS poli.... 0 SIP Video CAC Call Stats Total Num of video calls in progress........... 0 Num of video roaming calls in progress......... 0 Total Num of video calls since AP joined....... 0 Total Num of video roaming calls since AP j.... 0 Total Num of video calls rejected(Insuff BW.... 0 Total Num of video roam calls rejected(Insu.... 0 Band Select Stats Num of dual band client ....................... 0 Num of dual band client added.................. 0 Num of dual band client expired ............... 0 Num of dual band client replaced............... 0 Num of dual band client detected .............. 0 Num of suppressed client ...................... 0 Num of suppressed client expired............... 0 Num of suppressed client replaced.............. 0show ap summary
To display a summary of all lightweight access points attached to the controller, use the show ap summary command.
Syntax Description
(Optional) Type sequence of characters that make up the name of a specific AP or a group of APs, or enter a wild character search pattern.
Command History
Usage Guidelines
A list that contains each lightweight access point name, number of slots, manufacturer, MAC address, location, and the controller port number appears. When you specify
Examples
The following example shows how to display a summary of all connected access points:
> show ap summary Number of APs.................................... 2 Global AP username.............................. user Global AP Dot1x username........................ Not Configured Number of APs.................................... 2 Global AP username.............................. user Global AP Dot1x username........................ Not Configured AP Name Slots AP Model Ethernet MAC Location Port Country Priority -------- ----- ---------------- ----------------- ---------- ---- ------- -------- wolverine 2 AIR-LAP1252AG-A-K9 00:1b:d5:13:39:74 Reception 1 US 3 ap:1120 1 AIR-LAP1121G-A-K9 00:1b:d5:a9:ad:08 Hall 235 1 US 1show ap tcp-mss-adjust
To display the Basic Service Set Identifier (BSSID) value for each WLAN defined on an access point, use the show ap tcp-mss-adjust command.
Syntax Description
Note
If an AP itself is configured with the keyword all, the all access points case takes precedence over the AP that is with the keyword all.
Command History
show ap wlan
To display the Basic Service Set Identifier (BSSID) value for each WLAN defined on an access point, use the show ap wlan command.
Syntax Description
Command History
Examples
The following example shows how to display BSSIDs of an access point for the 802.11b network:
> show ap wlan 802.11b AP01 Site Name........................................ MY_AP_GROUP1 Site Description................................. MY_AP_GROUP1 WLAN ID Interface BSSID ------- ----------- -------------------------- 1 management 00:1c:0f:81:fc:20 2 dynamic 00:1c:0f:81:fc:21show auth-list
Command History
Examples
The following example shows how to display the access point authorization list:
> show auth-list Authorize APs against AAA...................... disabled Allow APs with Self-signed Certificate (SSC)... disabled Mac Addr Cert Type Key Hash ----------------------- ---------- ------------------------------------------ xx:xx:xx:xx:xx:xx MICshow client ap
Syntax Description
Usage Guidelines
The show client ap command may list the status of automatically disabled clients. Use the show exclusionlist command to view clients on the exclusion list (blacklisted).
show boot
To display the primary and backup software build numbers with an indication of which is active, use the show boot command.
Command History
Usage Guidelines
Each Cisco wireless LAN controller retains one primary and one backup operating system software load in nonvolatile RAM to allow controllers to boot off the primary load (default) or revert to the backup load when desired.
show call-control ap
NoteThe show call-control ap command is applicable only for SIP based calls.
To see the metrics for successful calls or the traps generated for failed calls, use the show call-control ap command.
Syntax Description
Command History
Usage Guidelines
To aid in troubleshooting, the output of this command shows an error code for any failed calls. This table explains the possible error codes for failed calls.
Examples
The following is a sample output of the show call-controller ap command that displays successful calls generated for an access point:
(Cisco Controller) >show call-control ap 802.11a Cisco_AP metrics Total Call Duration in Seconds................... 120 Number of Calls.................................. 10 Number of calls for given client is................. 1The following is a sample output of the show call-control ap command that displays metrics of traps generated for an AP.
(Cisco Controller) >show call-control ap 802.11a Cisco_AP traps Number of traps sent in one min.................. 2 Last SIP error code.............................. 404 Last sent trap timestamp...................... Jun 20 10:05:06show country
show country channels
To display the radio channels supported in the configured country, use the show country channels command.
Command History
Examples
The following example shows how to display the auto-RF channels for the configured countries:
> show country channels Configured Country............................. United States KEY: * = Channel is legal in this country and may be configured manually. Configured Country............................. United States KEY: * = Channel is legal in this country and may be configured manually. A = Channel is the Auto-RF default in this country. . = Channel is not legal in this country. C = Channel has been configured for use by Auto-RF. x = Channel is available to be configured for use by Auto-RF. ---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+- 802.11BG : Channels : 1 1 1 1 1 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 ---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+- US : A * * * * A * * * * A . . . ---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- 802.11A : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6 : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5 ---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- US : . A . A . A . A A A A A * * * * * . . . * * * A A A A * ---------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-show country supported
Command History
Examples
The following example shows how to display a list of all the supported countries:
> show country supported Configured Country............................. United States Supported Country Codes AR - Argentina................................. 802.11a / 802.11b / 802.11g AT - Austria................................... 802.11a / 802.11b / 802.11g AU - Australia................................. 802.11a / 802.11b / 802.11g BR - Brazil.................................... 802.11a / 802.11b / 802.11g BE - Belgium................................... 802.11a / 802.11b / 802.11g BG - Bulgaria.................................. 802.11a / 802.11b / 802.11g CA - Canada.................................... 802.11a / 802.11b / 802.11g CH - Switzerland............................... 802.11a / 802.11b / 802.11g CL - Chile..................................... 802.11b / 802.11g CN - China..................................... 802.11a / 802.11b / 802.11g CO - Colombia.................................. 802.11b / 802.11g CY - Cyprus.................................... 802.11a / 802.11b / 802.11g CZ - Czech Republic............................ 802.11a / 802.11b DE - Germany................................... 802.11a / 802.11b / 802.11g DK - Denmark................................... 802.11a / 802.11b / 802.11g EE - Estonia................................... 802.11a / 802.11b / 802.11g ES - Spain..................................... 802.11a / 802.11b / 802.11g FI - Finland................................... 802.11a / 802.11b / 802.11g FR - France.................................... 802.11a / 802.11b / 802.11g GB - United Kingdom............................ 802.11a / 802.11b / 802.11g GI - Gibraltar................................. 802.11a / 802.11b / 802.11g GR - Greece.................................... 802.11a / 802.11b / 802.11g HK - Hong Kong................................. 802.11a / 802.11b / 802.11g HU - Hungary................................... 802.11a / 802.11b / 802.11g ID - Indonesia................................. 802.11b / 802.11g IE - Ireland................................... 802.11a / 802.11b / 802.11g IN - India..................................... 802.11a / 802.11b / 802.11g IL - Israel.................................... 802.11a / 802.11b / 802.11g ILO - Israel (outdoor).......................... 802.11b / 802.11g IS - Iceland................................... 802.11a / 802.11b / 802.11g IT - Italy..................................... 802.11a / 802.11b / 802.11g JP - Japan (J)................................. 802.11a / 802.11b / 802.11g J2 - Japan 2(P)................................ 802.11a / 802.11b / 802.11g J3 - Japan 3(U)................................ 802.11a / 802.11b / 802.11g KR - Korea Republic (C)........................ 802.11a / 802.11b / 802.11g KE - Korea Extended (K)........................ 802.11a / 802.11b / 802.11g LI - Liechtenstein............................. 802.11a / 802.11b / 802.11g LT - Lithuania................................. 802.11a / 802.11b / 802.11g LU - Luxembourg................................ 802.11a / 802.11b / 802.11g LV - Latvia.................................... 802.11a / 802.11b / 802.11g MC - Monaco.................................... 802.11a / 802.11b / 802.11g MT - Malta..................................... 802.11a / 802.11b / 802.11g MX - Mexico.................................... 802.11a / 802.11b / 802.11g MY - Malaysia.................................. 802.11a / 802.11b / 802.11g NL - Netherlands............................... 802.11a / 802.11b / 802.11g NZ - New Zealand............................... 802.11a / 802.11b / 802.11g NO - Norway.................................... 802.11a / 802.11b / 802.11g PA - Panama.................................... 802.11b / 802.11g PE - Peru...................................... 802.11b / 802.11g PH - Philippines............................... 802.11a / 802.11b / 802.11g PL - Poland.................................... 802.11a / 802.11b / 802.11g PT - Portugal.................................. 802.11a / 802.11b / 802.11g RU - Russian Federation........................ 802.11a / 802.11b / 802.11g RO - Romania................................... 802.11a / 802.11b / 802.11g SA - Saudi Arabia.............................. 802.11a / 802.11b / 802.11g SE - Sweden.................................... 802.11a / 802.11b / 802.11g SG - Singapore................................. 802.11a / 802.11b / 802.11g SI - Slovenia.................................. 802.11a / 802.11b / 802.11g SK - Slovak Republic........................... 802.11a / 802.11b / 802.11g TH - Thailand.................................. 802.11b / 802.11g TR - Turkey.................................... 802.11b / 802.11g TW - Taiwan.................................... 802.11a / 802.11b / 802.11g UA - Ukraine................................... 802.11a / 802.11b / 802.11g US - United States............................. 802.11a / 802.11b / 802.11g USL - United States (Legacy).................... 802.11a / 802.11b / 802.11g USX - United States (US + chan165).............. 802.11a / 802.11b / 802.11g VE - Venezuela................................. 802.11b / 802.11g ZA - South Africa.............................. 802.11a / 802.11b / 802.11gshow dtls connections
To display the Datagram Transport Layer Security (DTLS) server status, use the show dtls connections command.
Command History
Examples
The following is a sample output of the show dtls connections command.
Device > show dtls connections AP Name Local Port Peer IP Peer Port Ciphersuite --------------- ------------- --------------- ------------- ----------------------- 1130 Capwap_Ctrl 1.100.163.210 23678 TLS_RSA _WITH_AES_128_CBC_SHA 1130 Capwap_Data 1.100.163.210 23678 TLS_RSA _WITH_AES_128_CBC_SHA 1240 Capwap_Ctrl 1.100.163.209 59674 TLS_RSA _WITH_AES_128_CBC_SHAshow ipv6 ra-guard
Syntax Description
Command History
Examples
The following example show the output of the show ipv6 ra-guard ap summary command:
(Cisco Controller) >show ipv6 ra-guard ap summary IPv6 RA Guard on AP..................... Enabled RA Dropped per client: MAC Address AP Name WLAN/GLAN Number of RA Dropped ----------------- ----------------- -------------- --------------------- 00:40:96:b9:4b:89 Bhavik_1130_1_p13 2 19 ----------------- ----------------- -------------- --------------------- Total RA Dropped on AP...................... 19The following example shows how to display the RA guard statistics for a controller:
(Cisco Controller) >show ipv6 ra-guard wlc summary IPv6 RA Guard on WLC.................... Enabledshow msglog
Command History
Usage Guidelines
If there are more that 15 entries, you are prompted to display the messages shown in the example.
Examples
The following example shows how to display message logs:
> show msglog Message Log Severity Level..................... ERROR Thu Aug 4 14:30:08 2005 [ERROR] spam_lrad.c 1540: AP 00:0b:85:18:b6:50 associated. Last AP failure was due to Link Failure Thu Aug 4 14:30:08 2005 [ERROR] spam_lrad.c 13840: Updating IP info for AP 00: 0b:85:18:b6:50 -- static 0, 1.100.49.240/255.255.255.0, gtw 1.100.49.1 Thu Aug 4 14:29:32 2005 [ERROR] dhcpd.c 78: dhcp server: binding to 0.0.0.0 Thu Aug 4 14:29:32 2005 [ERROR] rrmgroup.c 733: Airewave Director: 802.11a switch group reset Thu Aug 4 14:29:32 2005 [ERROR] rrmgroup.c 733: Airewave Director: 802.11bg sw itch group reset Thu Aug 4 14:29:22 2005 [ERROR] sim.c 2841: Unable to get link state for primary port 0 of interface ap-manager Thu Aug 4 14:29:22 2005 [ERROR] dtl_l2_dot1q.c 767: Unable to get USP Thu Aug 4 14:29:22 2005 Previous message occurred 2 times Thu Aug 4 14:29:14 2005 [CRITICAL] osapi_sem.c 794: Error! osapiMutexTake called with NULL pointer: osapi_bsntime.c:927 Thu Aug 4 14:29:14 2005 [CRITICAL] osapi_sem.c 794: Error! osapiMutexTake called with NULL pointer: osapi_bsntime.c:919 Thu Aug 4 14:29:14 2005 [CRITICAL] hwutils.c 1861: Security Module not found Thu Aug 4 14:29:13 2005 [CRITICAL] bootos.c 791: Starting code...show network summary
To display the network configuration of the Cisco wireless LAN controller, use the show network summary command.
Examples
This example shows how to display a summary configuration:
> show network summary RF-Network Name............................. RF Web Mode.................................... Disable Secure Web Mode............................. Enable Secure Web Mode Cipher-Option High.......... Disable Secure Web Mode Cipher-Option SSLv2......... Disable Secure Web Mode RC4 Cipher Preference....... Disable OCSP........................................ Disabled OCSP responder URL.......................... Secure Shell (ssh).......................... Enable Telnet...................................... Enable Ethernet Multicast Mode..................... Disable Mode: Ucast Ethernet Broadcast Mode..................... Disable Ethernet Multicast Forwarding............... Disable Ethernet Broadcast Forwarding............... Disable AP Multicast/Broadcast Mode................. Unicast IGMP snooping............................... Disabled IGMP timeout................................ 60 seconds IGMP Query Interval......................... 20 seconds MLD snooping................................ Disabled MLD timeout................................. 60 seconds MLD query interval.......................... 20 seconds User Idle Timeout........................... 300 seconds AP Join Priority............................ Disable ARP Idle Timeout............................ 300 seconds ARP Unicast Mode............................ Disabled Cisco AP Default Master..................... Disable Mgmt Via Wireless Interface................. Disable Mgmt Via Dynamic Interface.................. Disable Bridge MAC filter Config.................... Enable Bridge Security Mode........................ EAP Over The Air Provisioning of AP's........... Enable Apple Talk ................................. Disable Mesh Full Sector DFS........................ Enable AP Fallback ................................ Disable Web Auth CMCC Support ...................... Disabled Web Auth Redirect Ports .................... 80 Web Auth Proxy Redirect ................... Disable Web Auth Captive-Bypass .................. Disable Web Auth Secure Web ....................... Enable Fast SSID Change ........................... Disabled AP Discovery - NAT IP Only ................. Enabled IP/MAC Addr Binding Check .................. Enabled CCX-lite status ............................ Disable oeap-600 dual-rlan-ports ................... Disable oeap-600 local-network ..................... Enable mDNS snooping............................... Disabled mDNS Query Interval......................... 15 minutesshow redundancy summary
Command History
Examples
The following example shows how to display the redundancy summary information of the controller:
> show redundancy summary Redundancy Mode = SSO DISABLED Local State = ACTIVE Peer State = N/A Unit = Primary Unit ID = 88:43:E1:7E:03:80 Redundancy State = N/A Mobility MAC = 88:43:E1:7E:03:80 Network Monitor = ENABLED Link Encryption = DISABLED Redundancy Management IP Address................. 9.4.92.12 Peer Redundancy Management IP Address............ 9.4.92.14 Redundancy Port IP Address....................... 169.254.92.12 Peer Redundancy Port IP Address.................. 169.254.92.14show redundancy latency
To display the average latency to reach the management gateway and the peer redundancy management IP address, use the show redundancy latency command .
Command History
Examples
The following example shows how to display the average latency to reach the management gateway and the peer redundancy management IP address:
> show redundancy latency Network Latencies (RTT) for the Peer Reachability on the Redundancy Port in micro seconds for the past 10 intervals Peer Reachability Latency[ 1 ] : 524 usecs Peer Reachability Latency[ 2 ] : 524 usecs Peer Reachability Latency[ 3 ] : 522 usecs Peer Reachability Latency[ 4 ] : 526 usecs Peer Reachability Latency[ 5 ] : 524 usecs Peer Reachability Latency[ 6 ] : 524 usecs Peer Reachability Latency[ 7 ] : 522 usecs Peer Reachability Latency[ 8 ] : 522 usecs Peer Reachability Latency[ 9 ] : 526 usecs Peer Reachability Latency[ 10 ] : 523 usecs Network Latencies (RTT) for the Management Gateway Reachability in micro seconds for the past 10 intervals Gateway Reachability Latency[ 1 ] : 1347 usecs Gateway Reachability Latency[ 2 ] : 2427 usecs Gateway Reachability Latency[ 3 ] : 1329 usecs Gateway Reachability Latency[ 4 ] : 2014 usecs Gateway Reachability Latency[ 5 ] : 2675 usecs Gateway Reachability Latency[ 6 ] : 731 usecs Gateway Reachability Latency[ 7 ] : 1882 usecs Gateway Reachability Latency[ 8 ] : 2853 usecs Gateway Reachability Latency[ 9 ] : 832 usecs Gateway Reachability Latency[ 10 ] : 3708 usecsshow redundancy interfaces
To display details of redundancy and service port IP addresses, use the show redundancy interfaces command.Command History
Examples
The following example shows how to display the redundancy and service port IP addresses information:
> show redundancy interfaces Redundancy Management IP Address................. 9.4.120.5 Peer Redundancy Management IP Address............ 9.4.120.3 Redundancy Port IP Address....................... 169.254.120.5 Peer Redundancy Port IP Address.................. 169.254.120.3 Peer Service Port IP Address..................... 10.104.175.189show redundancy mobilitymac
show redundancy peer-route summary
To display the routes assigned to the standby WLC, use the show redundancy peer-route summary command.
Command History
Examples
The following example shows how to display all the configured routes of the standby WLC:
> show redundancy peer-route summary Number of Routes................................. 1 Destination Network Netmask Gateway ------------------- ------------------- ------------------- xxx.xxx.xxx.xxx 255.255.255.0 xxx.xxx.xxx.xxxshow redundancy statistics
To display the statistics information of the Redundancy Manager, use the show redundancy statistics command.Command History
Usage Guidelines
This command displays the statistics of different redundancy counters.
Local Physical Ports - Connectivity status of each physical port of the controller. 1 indicates that the port is up and 0 indicates that the port is down.
Peer Physical Ports - Connectivity status of each physical port of the peer controller. 1 indicates that the port is up and 0 indicates that the port is down.
Examples
The following example shows how to display the statistics information of the Redundancy Manager:
> show redundancy statistics Redundancy Manager Statistics Keep Alive Request Send Counter : 16 Keep Alive Response Receive Counter : 16 Keep Alive Request Receive Counter : 500322 Keep Alive Response Send Counter : 500322 Ping Request to Default GW Counter : 63360 Ping Response from Default GW Counter : 63360 Ping Request to Peer Counter : 12 Ping Response from Peer Counter : 3 Keep Alive Loss Counter : 0 Default GW Loss Counter : 0 Local Physical Ports 1...8 : 10000000 Peer Physical Ports 1...8 : 10000000capwap ap Commands
- capwap ap controller ip address
- capwap ap dot1x
- capwap ap hostname
- capwap ap ip address
- capwap ap ip default-gateway
- capwap ap log-server
- capwap ap primary-base
- capwap ap primed-timer
- capwap ap secondary-base
- capwap ap tertiary-base
- lwapp ap controller ip address
capwap ap controller ip address
To configure the controller IP address into the CAPWAP access point from the access point’s console port, use the capwap ap controller ip address command.
Syntax Description
Command History
capwap ap dot1x
To configure the dot1x username and password into the CAPWAP access point from the access point’s console port, use the capwap ap dot1x command.
Syntax Description
Command History
capwap ap hostname
To configure the access point host name from the access point’s console port, use the capwap ap hostname command.
Syntax Description
Command History
Usage Guidelines
This command must be entered from an access point’s console port.
capwap ap ip address
To configure the IP address into the CAPWAP access point from the access point’s console port, use the capwap ap ip address command.
Syntax Description
Command History
capwap ap ip default-gateway
To configure the default gateway from the access point’s console port, use the capwap ap ip default-gateway command.
Syntax Description
Command History
capwap ap log-server
To configure the system log server to log all the CAPWAP errors, use the capwap ap log-server command.
Syntax Description
Command History
capwap ap primary-base
To configure the primary controller name and IP address into the CAPWAP access point from the access point’s console port, use the capwap ap primary-base command.
Syntax Description
Command History
capwap ap primed-timer
capwap ap secondary-base
To configure the name and IP address of the secondary Cisco WLC into the CAPWAP access point from the access point’s console port, use the capwap ap secondary-base command.
Syntax Description
Command History
capwap ap tertiary-base
To configure the name and IP address of the tertiary Cisco WLC into the CAPWAP access point from the access point’s console port, use the capwap ap tertiary-base command.
Syntax Description
Command History
lwapp ap controller ip address
To configure the Cisco WLC IP address into the FlexConnect access point from the access point’s console port, use the lwapp ap controller ip address command.
Syntax Description
Command History
Usage Guidelines
This command must be entered from an access point’s console port.
Prior to changing the FlexConnect configuration on an access point using the access point’s console port, the access point must be in standalone mode (not connected to a controller) and you must remove the current LWAPP private configuration by using the clear lwapp private-config command.
Note
The access point must be running Cisco IOS Release 12.3(11)JX1 or higher releases.
config Commands
This section lists the config commands to configure access points.
- config 802.11-a antenna extAntGain
- config 802.11-a channel ap
- config 802.11-a txpower ap
- config 802.11 antenna diversity
- config 802.11 antenna extAntGain
- config 802.11 antenna mode
- config 802.11 antenna selection
- config 802.11 beamforming
- config 802.11 disable
- config advanced 802.11 profile clients
- config advanced 802.11 profile customize
- config advanced 802.11 profile foreign
- config advanced 802.11 profile noise
- config advanced 802.11 profile throughput
- config advanced 802.11 profile utilization
- config advanced backup-controller primary
- config advanced backup-controller secondary
- config advanced client-handoff
- config advanced dot11-padding
- config advanced assoc-limit
- config advanced max-1x-sessions
- config advanced rate
- config advanced probe backoff
- config advanced probe filter
- config advanced probe limit
- config advanced timers
- config ap
- config ap autoconvert
- config ap bhrate
- config ap bridgegroupname
- config ap bridging
- config ap cdp
- config ap core-dump
- config ap crash-file clear-all
- config ap crash-file delete
- config ap crash-file get-crash-file
- config ap crash-file get-radio-core-dump
- config ap 802.1Xuser
- config ap 802.1Xuser delete
- config ap 802.1Xuser disable
- config ap ethernet duplex
- config ap ethernet duplex
- config ap ethernet tag
- config ap group-name
- config ap hotspot
- config ap image predownload
- config ap image swap
- config ap led-state
- config ap link-encryption
- config ap link-latency
- config ap location
- config ap logging syslog level
- config ap max-count
- config ap mgmtuser add
- config ap mgmtuser delete
- config ap mode
- config ap monitor-mode
- config ap name
- config ap packet-dump
- config ap port
- config ap power injector
- config ap power pre-standard
- config ap primary-base
- config ap priority
- config ap reporting-period
- config ap reset
- config ap retransmit interval
- config ap retransmit count
- config ap role
- config ap rst-button
- config ap secondary-base
- config ap sniff
- config ap ssh
- config ap static-ip
- config ap stats-timer
- config ap syslog host global
- config ap syslog host specific
- config ap tcp-mss-adjust
- config ap telnet
- config ap tertiary-base
- config ap tftp-downgrade
- config ap username
- config ap venue
- config ap wlan
- config country
- config ipv6 ra-guard
- config known ap
- config network allow-old-bridge-aps
- config network ap-discovery
- config network ap-fallback
- config network ap-priority
- config network apple-talk
- config network bridging-shared-secret
- config network master-base
- config network oeap-600 dual-rlan-ports
- config network oeap-600 local-network
- config network otap-mode
- config network zero-config
- config redundancy interface address peer-service-port
- config redundancy mobilitymac
- config redundancy mode
- config redundancy peer-route
- config redundancy timer keep-alive-timer
- config redundancy timer peer-search-timer
- config redundancy unit
- redundancy force-switchover
- config slot
- config wgb vlan
config 802.11-a antenna extAntGain
To configure the external antenna gain for the 4.9-GHz and 5.8-GHz public safety channels on an access point, use the config 802.11-a antenna extAntGain commands.
Syntax Description
Command History
config 802.11-a channel ap
To configure the channel properties for the 4.9-GHz and 5.8-GHz public safety channels on an access point, use the config 802.11-a channel ap command.
Syntax Description
Command History
config 802.11-a txpower ap
To configure the transmission power properties for the 4.9-GHz and 5.8-GHz public safety channels on an access point, use the config 802.11-a txpower ap command.
Syntax Description
Command Default
The default transmission power properties for the 4.9-GHz and 5.8-GHz public safety channels on an access point is disabled.
Command History
config 802.11 antenna diversity
To configure the diversity option for 802.11 antennas, use the config 802.11 antenna diversity command.
Syntax Description
Command History
Examples
The following example shows how to enable antenna diversity for AP01 on an 802.11b network:
(Cisco Controller) >config 802.11a antenna diversity enable AP01The following example shows how to enable diversity for AP01 on an 802.11a network, using an external antenna connected to the Cisco lightweight access point left port (sideA):
(Cisco Controller) >config 802.11a antenna diversity sideA AP01config 802.11 antenna extAntGain
To configure external antenna gain for an 802.11 network, use the config 802.11 antenna extAntGain command.
Syntax Description
Command History
config 802.11 antenna mode
config 802.11 antenna selection
config 802.11 beamforming
To enable or disable Beamforming (ClientLink) on the network or on individual radios, enter the config 802.11 beamforming command.
Syntax Description
Command History
Usage Guidelines
When you enable Beamforming on the network, it is automatically enabled for all the radios applicable to that network type.
Follow these guidelines for using Beamforming:
- Beamforming is supported only for legacy orthogonal frequency-division multiplexing (OFDM) data rates (6, 9, 12, 18, 24, 36, 48, and 54 mbps).
Note
Beamforming is not supported for complementary-code keying (CCK) data rates (1, 2, 5.5, and 11 Mbps).
- Beamforming is supported only on access points that support 802.11n (AP1250 and AP1140).
- Two or more antennas must be enabled for transmission.
- All three antennas must be enabled for reception.
- OFDM rates must be enabled. If the antenna configuration restricts operation to a single transmit antenna, or if OFDM rates are disabled, Beamforming is not used.
config 802.11 disable
config advanced 802.11 profile clients
To set the Cisco lightweight access point clients threshold between 1 and 75 clients, use the config advanced 802.11 profile clients command.
Syntax Description
Command History
Examples
The following example shows how to set all Cisco lightweight access point clients thresholds to 25 clients:
(Cisco Controller) >config advanced 802.11 profile clients global 25 Global client count profile set.The following example shows how to set the AP1 clients threshold to 75 clients:
(Cisco Controller) >config advanced 802.11 profile clients AP1 75 Global client count profile set.config advanced 802.11 profile customize
To turn customizing on or off for an 802.11a Cisco lightweight access point performance profile, use the config advanced 802.11 profile customize command.
Syntax Description
Customizes performance profiles for this Cisco lightweight access point.
Uses global default performance profiles for this Cisco lightweight access point.
Command History
config advanced 802.11 profile foreign
To set the foreign 802.11a transmitter interference threshold between 0 and 100 percent, use the config advanced 802.11 profile foreign command.
Syntax Description
Command History
Examples
The following example shows how to set the foreign 802.11a transmitter interference threshold for all Cisco lightweight access points to 50 percent:
(Cisco Controller) >config advanced 802.11a profile foreign global 50The following example shows how to set the foreign 802.11a transmitter interference threshold for AP1 to 0 percent:
(Cisco Controller) >config advanced 802.11 profile foreign AP1 0config advanced 802.11 profile noise
To set the 802.11a foreign noise threshold between –127 and 0 dBm, use the config advanced 802.11 profile noise command.
Syntax Description
Command History
Examples
The following example shows how to set the 802.11a foreign noise threshold for all Cisco lightweight access points to –127 dBm:
(Cisco Controller) >config advanced 802.11a profile noise global -127The following example shows how to set the 802.11a foreign noise threshold for AP1 to 0 dBm:
(Cisco Controller) >config advanced 802.11a profile noise AP1 0config advanced 802.11 profile throughput
To set the Cisco lightweight access point data-rate throughput threshold between 1000 and 10000000 bytes per second, use the config advanced 802.11 profile throughput command.
Syntax Description
Configures all 802.11a Cisco lightweight access point specific profiles.
802.11a Cisco lightweight access point throughput threshold between 1000 and 10000000 bytes per second.
Command Default
The default Cisco lightweight access point data-rate throughput threshold value is 1,000,000 bytes per second.
Command History
Examples
The following example shows how to set all Cisco lightweight access point data-rate thresholds to 1000 bytes per second:
(Cisco Controller) >config advanced 802.11 profile throughput global 1000The following example shows how to set the AP1 data-rate threshold to 10000000 bytes per second:
(Cisco Controller) >config advanced 802.11 profile throughput AP1 10000000config advanced 802.11 profile utilization
To set the RF utilization threshold between 0 and 100 percent, use the config advanced 802.11 profile utilization command. The operating system generates a trap when this threshold is exceeded.
Syntax Description
Command History
Examples
The following example shows how to set the RF utilization threshold for all Cisco lightweight access points to 0 percent:
(Cisco Controller) >config advanced 802.11 profile utilization global 0The following example shows how to set the RF utilization threshold for AP1 to 100 percent:
(Cisco Controller) >config advanced 802.11 profile utilization AP1 100config advanced backup-controller primary
config advanced backup-controller secondary
config advanced client-handoff
config advanced dot11-padding
config advanced assoc-limit
To configure the rate at which access point radios send association and authentication requests to the controller, use the config advanced assoc-limit command.
Syntax Description
Command History
config advanced max-1x-sessions
config advanced probe backoff
config advanced probe filter
config advanced probe limit
To limit the number of probes sent to the WLAN controller per access point per client in a given interval, use the config advanced probe limit command.
Syntax Description
Number of probe requests (from 1 to 100) forwarded to the controller per client per access point radio in a given interval.
Command Default
The default number of probe requests is 2. The default interval is 500 milliseconds.
Command History
config advanced timers
config advanced timers { ap-discovery-timeout discovery-timeout | ap-fast-heartbeat { local | flexconnect | all} { enable | disable} fast_heartbeat_seconds | ap-heartbeat-timeout heartbeat_seconds | ap-primary-discovery-timeout primary_discovery_timeout | ap-primed-join-timeout primed_join_timeout | auth-timeout auth_timeout | pkt-fwd-watchdog { enable | disable} { watchdog_timer | default} | eap-identity-request-delay eap_identity_request_delay | eap-timeout eap_timeout}
Syntax Description
Command History
Usage Guidelines
The Cisco lightweight access point discovery timeout indicates how often a Cisco WLC attempts to discover unconnected Cisco lightweight access points.
The Cisco lightweight access point heartbeat timeout controls how often the Cisco lightweight access point sends a heartbeat keepalive signal to the Cisco Wireless LAN Controller.
Examples
The following example shows how to configure an access point discovery timeout with a timeout value of 20:
(Cisco Controller) >config advanced timers ap-discovery-timeout 20The following example shows how to enable the fast heartbeat interval for an access point in FlexConnect mode:
(Cisco Controller) >config advanced timers ap-fast-heartbeat flexconnect enable 8The following example shows how to configure the authentication timeout to 20 seconds:
(Cisco Controller) >config advanced timers auth-timeout 20config ap
To configure a Cisco lightweight access point or to add or delete a third-party (foreign) access point, use the config ap command.
Syntax Description
Command History
Examples
The following example shows how to disable lightweight access point AP1:
(Cisco Controller) >config ap disable AP1The following example shows how to add a foreign access point with MAC address 12:12:12:12:12:12 and IP address 192.12.12.1 from port 2033:
(Cisco Controller) >config ap add 12:12:12:12:12:12 2033 enable 192.12.12.1config ap autoconvert
To automatically convert all access points to FlexConnect mode or Monitor mode upon associating with the Cisco WLC, use the config ap autoconvert command.
Syntax Description
flexconnect
Configures all the access points automatically to FlexConnect mode.
Configures all the access points automatically to monitor mode.
Command History
Usage Guidelines
When access points in local mode connect to a Cisco 7500 Series Wireless Controller, they do not serve clients. The access point details are available in the controller. To enable access points to serve clients or perform monitoring related tasks when connected to the Cisco 7500 Series Wireless Controller, the access points must be in FlexConnect mode or Monitor mode.
config ap bhrate
Syntax Description
Cisco bridge backhaul Tx rate in kbps. The valid values are 6000, 12000, 18000, 24000, 36000, 48000, and 54000.
Command History
Usage Guidelines
In previous software releases, the default value for the bridge data rate was 24000 (24 Mbps). In controller software release 6.0, the default value for the bridge data rate is auto. If you configured the default bridge data rate value (24000) in a previous controller software release, the bridge data rate is configured with the new default value (auto) when you upgrade to controller software release 6.0. However, if you configured a non default value (for example, 18000) in a previous controller software release, that configuration setting is preserved when you upgrade to Cisco WLC Release 6.0.
When the bridge data rate is set to auto, the mesh backhaul chooses the highest rate where the next higher rate cannot be used due to unsuitable conditions for that specific rate (and not because of conditions that affect all rates).
config ap bridgegroupname
To set or delete a bridge group name on a Cisco lightweight access point, use the config ap bridgegroupname command.
Syntax Description
Command History
Usage Guidelines
Only access points with the same bridge group name can connect to each other. Changing the AP bridgegroupname may strand the bridge AP.
Examples
The following example shows how to delete a bridge group name on Cisco access point’s bridge group name AP02:
(Cisco Controller) >config ap bridgegroupname delete AP02 Changing the AP's bridgegroupname may strand the bridge AP. Please continue with caution. Changing the AP's bridgegroupname will also cause the AP to reboot. Are you sure you want to continue? (y/n)config ap bridging
config ap cdp
To configure the Cisco Discovery Protocol (CDP) on a Cisco lightweight access point, use the config ap cdp command.
config ap cdp { enable | disable | interface { ethernet interface_number | slot slot_id}} { cisco_ap | all}
Syntax Description
Note
If an AP itself is configured with the keyword all, the all access points case takes precedence over the AP that is with the keyword all.
Command Default
Enabled on radio interfaces of mesh APs and disabled on radio interfaces of non-mesh APs. Enabled on Ethernet interfaces of all APs.
Command History
Usage Guidelines
The config ap cdp disable all command disables CDP on all access points that are joined to the controller and all access points that join in the future. CDP remains disabled on both current and future access points even after the controller or access point reboots. To enable CDP, enter the config ap cdp enable all command.
Examples
The following example shows how to enable CDP on all access points:
(Cisco Controller) >config ap cdp enable allThe following example shows how to disable CDP on ap02 access point:
(Cisco Controller) >config ap cdp disable ap02The following example shows how to enable CDP for Ethernet interface number 2 on all access points:
(Cisco Controller) >config ap cdp ethernet 2 enable allconfig ap core-dump
To configure a Cisco lightweight access point’s memory core dump, use the config ap core-dump command.
config ap core-dump { disable | enable tftp_server_ipaddress filename { compress | uncompress} { cisco_ap | all}
Syntax Description
Note
If an AP itself is configured with the name ‘all’, then the ‘all access points’ case takes precedence over the AP that is named ‘all’.
Command History
config ap crash-file get-crash-file
config ap crash-file get-radio-core-dump
config ap 802.1Xuser
To configure the global authentication username and password for all access points currently associated with the controller as well as any access points that associate with the controller in the future, use the config ap 802.1Xuser command.
Syntax Description
Command History
config ap 802.1Xuser delete
config ap 802.1Xuser disable
To disable authentication for all access points or for a specific access point, use the config ap 802.1Xuser disable command.
Syntax Description
Command History
config ap ethernet duplex
To configure the Ethernet port duplex and speed settings of the lightweight access points, use the config ap ethernet duplex command.
Syntax Description
Command History
config ap ethernet duplex
To configure the Ethernet port duplex and speed settings of the lightweight access points, use the config ap ethernet duplex command.
Syntax Description
Command History
config ap ethernet tag
To configure VLAN tagging of the Control and Provisioning of Wireless Access Points protocol (CAPWAP) packets, use the config ap ethernet tag command.
Syntax Description
id Specifies the VLAN id.
vlan_id ID of the trunk VLAN.
disable Disables the VLAN tag feature. When you disable VLAN tagging, the access point untags the CAPWAP packets.
cisco_ap Name of the Cisco AP.
all Configures VLAN tagging on all the Cisco access points.
Command History
Usage Guidelines
After you configure VLAN tagging, the configuration comes into effect only after the access point reboots.
You cannot configure VLAN tagging on mesh access points.
If the access point is unable to route traffic or reach the controller using the specified trunk VLAN, it falls back to the untagged configuration. If the access point joins the controller using this fallback configuration, the controller sends a trap to a trap server such as the Cisco Prime Infrastructure, which indicates the failure of the trunk VLAN. In this scenario, the "Failover to untagged" message appears in show command output.
config ap group-name
config ap hotspot
config ap hotspot venue { type group_code type_code | name { add language_code venue_name | delete}} cisco_ap
Syntax Description
venue
Configures venue information for given AP group.
type
Configures the type of venue for given AP group.
group_code
Venue group information for given AP group.
type_code
Venue type information for the AP group.
For venue group 1 (ASSEMBLY), the following options are available:For venue group 2 (BUSINESS), the following options are available:For venue group 3 (EDUCATIONAL), the following options are available:For venue group 4 (FACTORY-INDUSTRIAL), the following options are available:type_code
name
Configures the name of venue for this access point.
language_code
ISO-639 encoded string defining the language used at the venue. This string is a three-character language code. For example, you can enter ENG for English.
venue_name
Venue name for this access point. This name is associated with the basic service set (BSS) and is used in cases where the SSID does not provide enough information about the venue. The venue name is case sensitive and can be up to 252 alphanumeric characters.
add
Adds the HotSpot venue name for this access point.
delete
Deletes the HotSpot venue name for this access point.
Command History
config ap image predownload
config ap image swap
config ap led-state
To configure the LED state of an access point or to configure the flashing of LEDs, use the config ap led-state command.
Syntax Description
seconds
Duration that the LEDs have to flash. The range is from 1 to 3600 seconds.
indefinite
Configures indefinite flashing of the access point’s LED.
dual-band
Configures the LED state for all dual-band access points.
Usage Guidelines
Note
If an AP itself is configured with the keyword all, the all access points case takes precedence over the AP that is with the keyword all.
LEDs on access points with dual-band radio module will flash green and blue when you execute the led state flash command.
Command History
config ap link-encryption
To configure the Datagram Transport Layer Security (DTLS) data encryption for access points on the 5500 series controller, use the config ap link-encryption command.
NoteIf an AP itself is configured with the keyword all, the all access points case takes precedence over the AP that is with the keyword all.
Syntax Description
enable
Enables the DTLS data encryption for access points.
disable
Disables the DTLS data encryption for access points.
cisco_ap
Name of a Cisco lightweight access point.
all
Specifies all access points.
Command Default
DTLS data encryption is enabled automatically for OfficeExtend access points but disabled by default for all other access points.
Command History
Usage Guidelines
Only Cisco 5500 Series Controllers support DTLS data encryption. This feature is not available on other controller platforms. If an access point with data encryption enabled tries to join any other controller, the access point joins the controller, but data packets are sent unencrypted.
Only Cisco 1130, 1140, 1240, and 1250 series access points support DTLS data encryption, and data-encrypted access points can join a Cisco 5500 Series Controller only if the wplus license is installed on the controller. If the wplus license is not installed, the access points cannot join the controller.
config ap link-latency
To configure link latency for a specific access point or for all access points currently associated to the controller, use the config ap link-latency command:
NoteIf an AP itself is configured with the keyword all, the all access points case takes precedence over the AP that is with the keyword all.
Syntax Description
Command History
config ap location
config ap logging syslog level
To set the severity level for filtering syslog messages for a particular access point or for all access points, use the config ap logging syslog level command.
Syntax Description
NoteIf an AP itself is configured with the keyword all, the all access points case takes precedence over the AP that is with the keyword all.
Command History
Usage Guidelines
If you set a syslog level, only those messages whose severity is equal to or less than that level are sent to the access point. For example, if you set the syslog level to Warnings (severity level 4), only those messages whose severity is between 0 and 4 are sent to the access point.
config ap max-count
To configure the maximum number of access points supported by the Cisco Wireless LAN Controller (WLC), use the config ap max-count command.
Syntax Description
Command History
Usage Guidelines
The access point count of the Cisco WLC license overrides this count if the configured value is greater than the access point count of the license. A value of 0 indicates that there is no restriction on the maximum number of access points. If high availability is configured, you must reboot both the active and the standby Cisco WLCs after you configure the maximum number of access points supported by the Cisco WLC.
config ap mgmtuser add
To configure username, password, and secret password for AP management, use the config ap mgmtuser add command.
Syntax Description
Configures the secret password for privileged AP management.
Applies configuration to every AP that does not have a specific username.
Command History
Usage Guidelines
The following requirements are enforced on the password:
- The password should contain characters from at least three of the following classes: lowercase letters, uppercase letters, digits, and special characters.
- No character in the password can be repeated more than three times consecutively.
- The password sould not contain management username or reverse of usename.
- The password should not contain words like Cisco, oscic, admin, nimda or any variant obtained by changing the capitalization of letters by substituting 1, |, or ! or substituting 0 for o or substituting $ for s. The following requirement is enforced on the secret password:
- The secret password should contain characters from at least three of the following classes: lowercase letters, uppercase letters, digits, or special characters.
config ap mgmtuser delete
config ap mode
To change a Cisco WLC communication option for an individual Cisco lightweight access point, use the config ap mode command.
config ap mode { bridge | flexconnect { submode { none | wips} | local { submode { none | wips} | reap | rogue | sniffer | se-connect | monitor { submode { none | wips} } cisco_ap
Syntax Description
Converts from a lightweight access point to a mesh access point (bridge mode).
flexconnect
Converts from an indoor mesh access point (MAP or RAP) to a nonmesh lightweight access point (local mode).
Command History
Usage Guidelines
The sniffer mode captures and forwards all the packets from the clients on that channel to a remote machine that runs AiroPeek or other supported packet analyzer software. It includes information on the timestamp, signal strength, packet size and so on.
Examples
The following example shows how to set the controller to communicate with access point AP91 in bridge mode:
> config ap mode bridge AP91The following example shows how to set the controller to communicate with access point AP01 in local mode:
> config ap mode local AP01The following example shows how to set the controller to communicate with access point AP91 in remote office (REAP) mode:
> config ap mode flexconnect AP91The following example shows how to set the controller to communicate with access point AP91 in a wired rogue access point detector mode:
> config ap mode rogue AP91The following example shows how to set the controller to communicate with access point AP02 in wireless sniffer mode:
> config ap mode sniffer AP02config ap monitor-mode
To configure Cisco lightweight access point channel optimization, use the config ap monitor-mode command.
config ap monitor-mode { 802.11b fast-channel | no-optimization | tracking-opt | wips-optimized} cisco_ap
Syntax Description
Command History
config ap packet-dump
config ap packet-dump { buffer-size size | capture-time time | ftp serverip ip-address path path username user_ID password password | start mac_address cisco_ap | stop | truncate length}
config ap packet-dump classifier {{ arp | broadcast | control | data | dot1x | iapp | ip | management | multicast } { enable | disable} | tcp { enable | disable | port tcp_port } | udp { enable | disable | port udp_port } }
Syntax Description
buffer-size Configures the buffer size for Packet Capture in the access point.
size Size of the buffer. The range is from 1024 to 4096 KB.
capture-time Configures the timer value for Packet Capture.
time Timer value for Packet Capture. The range is from 1 to 60 minutes.
ftp Configures FTP parameters for Packet Capture.
serverip server_ip Configures the FTP server IP address.
path path Configures FTP server path.
username user_ID Configures the username for the FTP server.
password password Configures the password for the FTP server.
start Starts Packet Capture from the access point.
mac_address Client MAC Address for Packet Capture.
cisco_ap Name of the Cisco access point.
stop Stops Packet Capture from the access point.
truncate Truncates the packet to the specified length during Packet Capture.
length Length of the packet after truncation. The range is from 20 to 1500.
classifier Configures the classifier information for Packet Capture. You can specify the type of packets that needs to be captured.
arp Captures ARP packets.
enable Enables capture of ARP, broadcast, 802.11 control, 802.11 data, dot1x, Inter Access Point Protocol (IAPP), IP, 802.11 management, or multicast packets.
disable Disables capture of ARP, broadcast, 802.11 control, 802.11 data, dot1x, IAPP, IP, 802.11management, or multicast packets.
broadcast Captures broadcast packets.
control Captures 802.11 control packets.
data Captures 802.11 data packets.
dot1x Captures dot1x packets.
iapp Captures IAPP packets.
ip Captures IP packets.
management Captures 802.11 management packets.
multicast Captures multicast packets.
tcp Captures TCP packets.
tcp_port TCP port number. The range is from 1 to 65535.
udp Captures TCP packets.
udp_port UDP port number. The range is from 1 to 65535.
ftp Configures FTP parameters for Packet Capture.
server_ip FTP server IP address.
Command History
Usage Guidelines
Packet Capture does not work during intercontroller roaming.
The controller does not capture packets created in the radio firmware and sent out of the access point, such as a beacon or probe response. Only packets that flow through the Radio driver in the Tx path will be captured.
Use the command config ap packet-dump start to start the Packet Capture from the access point. When you start Packet Capture, the controller sends a Control and Provisioning of Wireless Access Points protocol (CAPWAP) message to the access point to which the client is associated and captures packets. You must configure the FTP server and ensure that the client is associated to the access point before you start Packet Capture. If the client is not associated to the access point, you must specify the name of the access point.
config ap power injector
To configure the power injector state for an access point, use the config ap power injector command.
Syntax Description
Note
If an AP itself is configured with the keyword all, the all access points case takes precedence over the AP that is with the keyword all.
Command History
config ap power pre-standard
To enable or disable the inline power Cisco pre-standard switch state for an access point, use the config ap power pre-standard command.
Syntax Description
Enables the inline power Cisco pre-standard switch state for an access point.
Disables the inline power Cisco pre-standard switch state for an access point.
Command History
config ap primary-base
To set the Cisco lightweight access point primary Cisco WLC, use the config ap primary-base command.
Syntax Description
Command History
Usage Guidelines
The Cisco lightweight access point associates with this Cisco WLC for all network operations and in the event of a hardware reset.
OfficeExtend access points do not use the generic broadcast or over-the air (OTAP) discovery process to find a controller. You must configure one or more controllers because OfficeExtend access points try to connect only to their configured controllers.
config ap priority
To assign a priority designation to an access point that allows it to reauthenticate after a controller failure by priority rather than on a first-come-until-full basis, use the config ap priority command.
Syntax Description
Command History
config ap retransmit interval
config ap retransmit count
config ap role
Syntax Description
Designates the mesh access point as a root access point (RAP).
Designates the mesh access point as a mesh access point (MAP).
Command History
config ap secondary-base
To set the Cisco lightweight access point secondary Cisco WLC, use the config ap secondary-base command.
Syntax Description
(Optional). If the backup Cisco WLC is outside the mobility group to which the access point is connected, then you need to provide the IP address of the primary, secondary, or tertiary Cisco WLC.
Note For OfficeExtend access points, you must enter both the name and IP address of the Cisco WLC. Otherwise, the access point cannot join this Cisco WLC.
Command History
Usage Guidelines
The Cisco lightweight access point associates with this Cisco WLC for all network operations and in the event of a hardware reset.
OfficeExtend access points do not use the generic broadcast or over-the air (OTAP) discovery process to find a Cisco WLC. You must configure one or more Cisco WLCs because OfficeExtend access points try to connect only to their configured Cisco WLCs.
config ap sniff
Syntax Description
Command History
Usage Guidelines
When the sniffer feature is enabled on an access point, it starts sniffing the signal on the given channel. It captures and forwards all the packets to the remote computer that runs Omnipeek, Airopeek, AirMagnet, or Wireshark software. It includes information on the timestamp, signal strength, packet size and so on.
Before an access point can act as a sniffer, a remote computer that runs one of the listed packet analyzers must be set up so that it can receive packets sent by the access point. After the Airopeek installation, copy the following .dll files to the location where airopeek is installed:
config ap ssh
config ap static-ip
To configure Cisco lightweight access point static IP address settings, use the config ap static-ip command.
config ap static-ip { enable cisco_ap ip_address net_mask gateway | disable cisco_ap add { domain { cisco_ap | all} domain_name} | { nameserver { cisco_ap | all} dns_ip_address} | delete { domain | nameserver} { cisco_ap | all}}
Syntax Description
Enables the Cisco lightweight access point static IP address.
Disables the Cisco lightweight access point static IP address. The access point uses DHCP to get the IP address.
Specifies the domain to which a specific access point or all access points belong.
Specifies a DNS server so that a specific access point or all access points can discover the controller using DNS resolution.
Note
If an AP itself is configured with the keyword all, the all access points case takes precedence over the AP that is with the keyword all.
Command History
Usage Guidelines
An access point cannot discover the controller using Domain Name System (DNS) resolution if a static IP address is configured for the access point, unless you specify a DNS server and the domain to which the access point belongs.
After you enter the IP, netmask, and gateway addresses, save your configuration to reboot the access point. After the access point rejoins the controller, you can enter the domain and DNS server information.
config ap stats-timer
To set the time in seconds that the Cisco lightweight access point sends its DOT11 statistics to the Cisco wireless LAN controller, use the config ap stats-timer command.
Syntax Description
Command History
config ap syslog host global
To configure a global syslog server for all access points that join the controller, use the config ap syslog host global command.
Syntax Description
Command History
Usage Guidelines
By default, the global syslog server IP address for all access points is 255.255.255.255. Make sure that the access points can reach the subnet on which the syslog server resides before configuring the syslog server on the controller. If the access points cannot reach this subnet, the access points are unable to send out syslog messages.
config ap syslog host specific
To configure a syslog server for a specific access point, use the config ap syslog host specific command.
Syntax Description
Command History
config ap tcp-mss-adjust
To enable or disable the TCP maximum segment size (MSS) on a particular access point or on all access points, use the config ap tcp-mss-adjust command.
Syntax Description
Note
If an AP itself is configured with the keyword all, the all access points case takes precedence over the AP that is with the keyword all.
Command History
Usage Guidelines
When you enable this feature, the access point checks for TCP packets to and from wireless clients in its data path. If the MSS of these packets is greater than the value that you configured or greater than the default value for the CAPWAP tunnel, the access point changes the MSS to the new configured value.
config ap telnet
config ap tertiary-base
To set the Cisco lightweight access point tertiary Cisco WLC, use the config ap tertiary-base command.
Syntax Description
(Optional) If the backup controller is outside the mobility group to which the access point is connected, then you need to provide the IP address of the primary, secondary, or tertiary Cisco WLC.
Note For OfficeExtend access points, you must enter both the name and IP address of the Cisco WLC. Otherwise, the access point cannot join this Cisco WLC.
Command History
Usage Guidelines
OfficeExtend access points do not use the generic broadcast or over-the air (OTAP) discovery process to find a Cisco WLC. You must configure one or more controllers because OfficeExtend access points try to connect only to their configured Cisco WLCs.
The Cisco lightweight access point associates with this Cisco WLC for all network operations and in the event of a hardware reset.
config ap tftp-downgrade
config ap username
config ap venue
To configure the venue information for 802.11u network on an access point, use the config ap venue command.
Syntax Description
Venue group category. See the table below for details on venue group mappings.
Venue type. This value depends on the venue-group specified. See the table below for venue group mappings.
Language used. An ISO-14962-1997 encoded string that defines the language. This string is a three character language code. Enter the first three letters of the language in English (for example, eng for English).
deletes
Deletes venue information.
Command History
config ap wlan
config country
Syntax Description
Command History
Usage Guidelines
Cisco WLCs must be installed by a network administrator or qualified IT professional and the installer must select the proper country code. Following installation, access to the unit should be password protected by the installer to maintain compliance with regulatory requirements and to ensure proper unit functionality. See the related product guide for the most recent country codes and regulatory domains.
You can use the show country command to display a list of supported countries.
config ipv6 ra-guard
config network allow-old-bridge-aps
config network ap-discovery
To enable or disable NAT IP in an AP discovery response, use the config network ap-discovery command.
Syntax Description
Command History
Usage Guidelines
If the config interface nat-address management command is set, this command controls which address(es) are sent in the CAPWAP discovery responses.
If all APs are on the outside of the NAT gateway of the controller, enter the config network ap-discovery nat-ip-only enable command, and only the management NAT address is sent.
If the controller has both APs on the outside and the inside of its NAT gateway, enter the config network ap-discovery nat-ip-only disable command, and both the management NAT address and the management inside address are sent. Ensure that you have entered the config ap link-latency disable all command to avoid stranding APs.
config network ap-priority
To enable or disable the option to prioritize lightweight access points so that after a controller failure they reauthenticate by priority rather than on a first-come-until-full basis, use the config network ap-priority command.
Syntax Description
Enables the lightweight access point priority reauthentication.
Disables the lightweight access point priority reauthentication.
Command History
config network bridging-shared-secret
Syntax Description
Command History
Usage Guidelines
This command creates a secret that encrypts backhaul user data for the mesh access points that connect to the switch.
The zero-touch configuration must be enabled for this command to work.
config network master-base
To enable or disable the Cisco wireless LAN controller as an access point default master, use the config network master-base command.
Syntax Description
Enables the Cisco wireless LAN controller acting as a Cisco lightweight access point default master.
Disables the Cisco wireless LAN controller acting as a Cisco lightweight access point default master.
Command History
Usage Guidelines
This setting is only used upon network installation and should be disabled after the initial network configuration. Because the Master Cisco wireless LAN controller is normally not used in a deployed network, the Master Cisco wireless LAN controller setting can be saved from 6.0.199.0 or later releases.
config network oeap-600 dual-rlan-ports
To configure the Ethernet port 3 of Cisco OfficeExtend 600 Series access points to operate as a remote LAN port in addition to port 4, use the config network oeap-600 dual-rlan-ports command.
Syntax Description
Enables Ethernet port 3 of Cisco OfficeExtend 600 Series access points to operate as a remote LAN port in addition to port 4.
Resets the Ethernet port 3 Cisco OfficeExtend 600 Series access points to function as a local LAN port.
Command History
config network oeap-600 local-network
To configure access to the local network for the Cisco 600 Series OfficeExtend access points, use the config network oeap-600 local-network command.
Syntax Description
Enables access to the local network for the Cisco 600 Series OfficeExtend access points.
Disables access to the local network for the Cisco 600 Series OfficeExtend access points.
Command History
config network otap-mode
config redundancy interface address peer-service-port
To configure the service port IP and netmask of the peer or standby controller, use the config redundancy interface address peer-service-port command.
Syntax Description
Command History
config redundancy mobilitymac
config redundancy mode
config redundancy peer-route
To configure the route configurations of the peer or standby controller, use the config redundancy peer-route command.
Syntax Description
add Adds a network route.
delete Deletes a network route specific to standby controller.
network_ip_address Network IP address.
netmask Subnet mask of the network.
gateway IP address of the gateway for the route network.
Command History
config redundancy timer keep-alive-timer
config redundancy timer peer-search-timer
config redundancy unit
redundancy force-switchover
To trigger a manual switch over on the active Cisco WLC, use the redundancy force-switchover command.
Command History
Usage Guidelines
When a manual switchover occurs, the active Cisco WLC reboots and the standby Cisco WLC takes over the network. A stateful switchover of access points (AP SSO) is supported. AP SSO ensures that the AP sessions are maintained after the standby Cisco WLC takes over and the APs switch over to the standby Cisco WLC. The clients on the active Cisco WLC deauthenticate and join the new active Cisco WLC.
config slot
config slot slot_id { enable | disable | channel ap | chan_width | txpower ap | antenna extAntGain antenna_gain | rts} cisco_ap
Syntax Description
Slot downlink radio to which the channel is assigned. Beginning in Release 7.5 and later releases, you can configure 802.11a on slot 1 and 802.11ac on slot 2.
External antenna gain value in .5 dBi units (such as 2.5 dBi = 5).
Name of the Cisco access point on which the channel is configured.
Command History
clear Commands
This section lists the clear commands to clear existing configurations, log files, and other functions for access points .
clear ap config
clear ap eventlog
To delete the existing event log and create an empty event log file for a specific access point or for all access points joined to the controller, use the clear ap eventlog command.
Syntax Description
Name of the access point for which the event log file will be emptied.
Deletes the event log for all access points joined to the controller.
Command History
clear ap join stats
clear ap tsm
To clear the Traffic Stream Metrics (TSM) statistics of clients associated to an access point, use the clear ap tsm command.
Syntax Description
802.11a Clears 802.11a TSM statistics of clients associated to an access point.
802.11b Clears 802.11b TSM statistics of clients associated to an access point.
cisco_ap Cisco lightweight access point.
all Clears TSM statistics of clients associated to the access point.
Command History
clear lwapp private-config
To clear (reset to default values) an access point’s current Lightweight Access Point Protocol (LWAPP) private configuration, which contains static IP addressing and controller IP address configurations, use the clear lwapp private-config command.
Command History
Usage Guidelines
Enter the command on the access point console port.
Prior to changing the FlexConnect configuration on an access point using the access point’s console port, the access point must be in standalone mode (not connected to a Cisco WLC ) and you must remove the current LWAPP private configuration by using the clear lwapp private-config command.
Note
The access point must be running Cisco Access Point IOS Release 12.3(11)JX1 or later releases.
debug Commands
This section lists the debug commands to manage debugging of access points managed by the controller.
CautionDebug commands are reserved for use only under the direction of Cisco personnel. Do not use these commands without direction from Cisco-certified staff.
- debug ap
- debug ap enable
- debug ap packet-dump
- debug ap show stats
- debug ap show stats video
- debug capwap
- debug group
- debug lwapp console cli
- debug rfac
- debug rmgr
- debug rsyncmgr
- debug service ap-monitor
debug ap
To configure the remote debugging of Cisco lightweight access points or to remotely execute a command on a lightweight access point, use the debug ap command.
Syntax Description
Enables the debugging on a lightweight access point.
Note The debugging information is displayed only to the controller console and does not send output to a controller Telnet/SSH CLI session.
Disables the debugging on a lightweight access point.
Note The debugging information is displayed only to the controller console and does not send output to a controller Telnet/SSH CLI session.
Specifies that a CLI command is to be executed on the access point.
Note The command to be executed must be enclosed in double quotes, such as debug ap command “led flash 30” AP03.
The output of the command displays only to the controller console and does not send output to a controller Telnet/SSH CLI session.
Command History
Examples
The following example shows how to enable the remote debugging on access point AP01:
> debug ap enable AP01The following example shows how to execute the config ap location command on access point AP02:
> debug ap command “config ap location "Building 1" AP02”The following example shows how to execute the flash LED command on access point AP03:
> debug ap command “led flash 30” AP03debug ap enable
To configure the remote debugging of Cisco lightweight access points or to remotely execute a command on a lightweight access point, use the debug ap enable command.
Syntax Description
Note The debugging information is displayed only to the controller console and does not send output to a controller Telnet/SSH CLI session.
Specifies that a CLI command is to be executed on the access point.
Note The command to be executed must be enclosed in double quotes, such as debug ap command “led flash 30” AP03.
The output of the command displays only to the controller console and does not send output to a controller Telnet/SSH CLI session.
Command History
Examples
The following example shows how to enable the remote debugging on access point AP01:
> debug ap enable AP01The following example shows how to disable the remote debugging on access point AP02:
> debug ap disable AP02The following example shows how to execute the flash LED command on access point AP03:
> debug ap command “led flash 30” AP03debug ap packet-dump
Syntax Description
enable Enables the debugging of Packet Capture of an access point.
disable Disables the debugging of Packet Capture of an access point.
Command History
debug ap show stats
To debug video messages and statistics of Cisco lightweight access points, use the debug ap show stats command.
debug ap show stats { 802.11a | 802.11b} cisco_ap { tx-queue | packet | load | multicast | client { client_MAC | video | all} | video metrics}
Syntax Description
Displays the QoS Basic Service Set (QBSS) and other statistics of the AP.
mgid
Displays detailed multicast information for a single multicast group ID (MGID).
mgid_database_number
Layer 2 MGID database number.
admission
Displays video admission control on the AP.
bandwidth
Displays video bandwidth on the AP.
Command History
Examples
The following example shows how to troubleshoot the access point AP01’s transmit queue traffic on an 802.11a network:
> debug ap show stats 802.11a AP01 tx-queueThe following example shows how to troubleshoot the access point AP02’s multicast supported rates on an 802.11b/g network:
> debug ap show stats 802.11b AP02 multicastThe following example shows how to troubleshoot the metrics of a client identified by its MAC address, associated with the access point AP01 on an 802.11a network:
> debug ap show stats 802.11a AP01 client 00:40:96:a8:f7:98The following example shows how to troubleshoot the metrics of all clients associated with the access point AP01 on an 802.11a network:
> debug ap show stats 802.11a AP01 client alldebug ap show stats video
To configure the debugging of video messages and statistics of Cisco lightweight access points, use the debug ap show stats video command.
Syntax Description
Command History
Examples
The following example shows how to configure the debugging of an access point AP01’s multicast group that is identified by the group’s Layer 2 MGID database number:
> debug ap show stats video AP01 multicast mgid 50This example shows how to configure the debugging of an access point AP01’s video bandwidth:
> debug ap show stats video AP01 bandwidthdebug capwap
To configure the debugging of Control and Provisioning of Wireless Access Points (CAPWAP) settings, use the debug capwap command.
debug capwap { detail | dtls-keepalive | errors | events | hexdump | info | packet | payload} { enable | disable}
Syntax Description
Configures the debugging for CAPWAP DTLS data keepalive packets settings.
Configures the debugging for CAPWAP hexadecimal dump settings.
Command History
debug lwapp console cli
debug rfac
Syntax Description
packet Configures the debugging of Redundancy Framework packets.
events Configures the debugging of Redundancy Framework events.
errors Configures the debugging of Redundancy Framework errors.
detail Configures the debugging of Redundancy Framework details.
enable (Optional) Enables the debugging of Redundancy Framework.
disable (Optional) Disables the debugging of Redundancy Framework.
Command History
debug rmgr
Syntax Description
packet Configures the debugging of Redundancy Manager packets.
events Configures the debugging of Redundancy Manager events.
errors Configures the debugging of Redundancy Manager errors.
detail Configures the debugging of Redundancy Manager details.
enable Enables the debugging of Redundancy Manager.
disable Disables the debugging of Redundancy Manager.
Command History
debug rsyncmgr
To configure the debugging of the Redundancy Sync Manager (RSYNCMGR), use the debug rsyncmgr command.
Syntax Description
packet Configures the debugging of Redundancy Sync Manager packets.
events Configures the debugging of Redundancy Sync Manager events.
errors Configures the debugging of Redundancy Sync Manager errors.
detail Configures the debugging of Redundancy Sync Manager details.
enable Enables the debugging of Redundancy Sync Manager.
disable Stops the debugging Redundancy Sync Manager.
Command History
transfer download peer-start
Command History
Examples
The following example shows how to start downloading a file to the peer controller:
> transfer download peer-start In commandTransferDownloadPeerStart Mode............................................TFTP Data Type.......................................Login Banner TFTP Server IP..................................9.1.0.100 TFTP Packet Timeout.............................6 TFTP Max Retries................................10 TFTP Path.......................................dhk/ TFTP Filename...................................xyz Are you sure you want to start download on standby? (y/N) y In commandTransferDownloadPeerStart In usmDbTransferDownStartSet.. dir: 2 ---> Indicates L7_TRANSFER_DIRECTION_DOWN_STANDBY usmDbTransferDownStartSet: SUCCESS In commandTransferDownloadPeerStart TFTP Config transfer starting. In commandTransferDownloadPeerStart % Error: Config file transfer failed - Error from server: File not foundtransfer upload peer-start
Command History
Examples
The following example shows how to start uploading a file to the peer controller:
> transfer upload peer-start Mode............................................. FTP FTP Server IP.................................... 209.165.201.1 FTP Server Port.................................. 21 FTP Path......................................... /builds/nimm/ FTP Filename..................................... AS_5500_7_4_1_20.aes FTP Username..................................... wnbu FTP Password..................................... ********* Data Type........................................ Error Log Are you sure you want to start upload from standby? (y/N) n Transfer CanceledResetting the System Reboot Time
reset system notify-time
test Commands
This section lists the test commands for access points.
test ap pmtu
To enable or disable the Path Maximum Transmission Unit (PMTU) on the CAPWAP tunnel of a Cisco access point, use the test ap command.
Syntax Description
enable Disables PMTU on the CAPWAP tunnel of a Cisco access point.
disable Enables PMTU on the CAPWAP tunnel of a Cisco access point.
cisco_ap Name of the Cisco lightweight access point.
test capwap
To configure an access point to send broadcast radio measurement requests to clients, or to enable the encryption of control packets that are sent between the access point and the controller, use the test capwap command.
Syntax Description
message Configures the access point to send a broadcast radio measurement requests to clients.
token Time interval for the access point to send a broadcast radio measurement requests to clients.
cisco_ap Name of the Cisco lightweight access point.
encr Encrypts or decrypts the control packets that are sent between the access point and the controller.
enable Enables the encryption or decryption of control packets that are sent between the access point and the controller.
disable Disables the encryption or decryption of control packets that are sent between the access point and the controller.
