Feedback
Table Of Contents
show platform feature-manager consistency-check
show platform hardware acl accounting
show platform hardware acl acct-xlt-tbl
show platform hardware acl adj-rit
show platform hardware acl capmap tcam
show platform hardware acl config-registers
show platform hardware acl destinfo
show platform hardware acl diagnostics
show platform hardware acl entry
show platform hardware acl ethertype-cam
show platform hardware acl hardware-hits
show platform hardware acl initiate-lookup
show platform hardware acl label2sel tcam
show platform hardware acl lou
show platform hardware acl status
show platform hardware acl tcam
show platform hardware acl tcp-flags-tbl
show platform hardware acl v6-extnhdr-tbl
show platform hardware asicreg
show platform hardware asic-versions
show platform hardware capacity
show platform hardware capacity rewrite-engine
show platform hardware cef mpls detail
show platform hardware cef adjacencies entry
show platform hardware cef tcam
show platform hardware cef adjacencies
show platform hardware cef maximum-route
show platform hardware database version
show platform hardware earl eureka
show platform hardware earl lamira
show platform hardware earl layer2
show platform hardware fan-tray
show platform hardware flow table
show platform hardware image version slot
show platform hardware lif stats
show platform hardware multicast routing
show platform hardware met read
show platform hardware statistics
show platform hardware transceiver xml version
show platform hardware virtual-map
show platform hardware xml version
show platform idbhal conversion
show platform multicast routing
show platform qos aggregate policer
show platform software e8-recovery
show platform feature-manager consistency-check
To display platform-specific feature manager consistency checker configuration details, use the show platform feature-manager consistency-check command.
show platform feature-manager consistency-check {all | log | now {all |default-in | default-out | dynamic | rbacl | static}
Syntax Description
Defaults
None.
Command Modes
Privileged EXEC mode.
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the all of the platform-specific feature manager consistency checker configurations:
Router# show platform feature-manager consistency-check allRelated Commands
clear platform feature-manager consistency-check all
Clears platform-specific feature manager consistency checker configurations.
show platform flow
To display NetFlow usage on the platform, use the show platform flow usage command.
show platform flow {aging | export {instance number | module number} | ip {count {instance number | module number} | destination ip address | instance number | module number | multicast | protocol number | source ip address} | ipv6 {count {instance number | module number} | destination ip address | instance number | module number | multicast | protocol number | source ip address} | layer2 {count {instance number | module number} | instance number | module number} | multicast | protocol number | source ip address} | mpls {count {instance number | module number} | instance number | module number} | table-contention {aggregate {instance number | module number} | detailed {instance number | module number} | summary {instance number | module number}} | usage {instance number | module number}}
Syntax Description
Command Default
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the NetFlow usage on module 4:
Router# show platform flow usage module 4Related Commands
show platform flow export
To display the Yielding Netflow Data Export (NDE) parameters, use the show platform flow export command in Priveleged EXEC mode.
show platform flow export module module
Syntax Description
Command Default
This command has no default settings.
Command Modes
Priveleged EXEC mode
Command History
Examples
The following example displays the feature-related information for NDE:
Router(config)# show platform flow export module 4Yielding NDE is enabled.Supervisor CPU threshold = 50Linecard CPU threshold = 70Module/Instance 1 :---------------------No of flows read and exported = 1802384No of flows discarded = 5230No of capture+purge requests = 23049No of purge-only requests = 120Module/Instance 5 :---------------------No of flows read and exported = 1No of flows discarded = 0No of capture+purge requests = 13481No of purge-only requests = 11lionel#lionel#lionel#sh pla flow exp mod 1Yielding NDE is enabled.Supervisor CPU threshold = 50Linecard CPU threshold = 70Module/Instance 1 :---------------------No of flows read and exported = 1802384No of flows discarded = 5230No of capture+purge requests = 23049No of purge-only requests = 120Related Commands
show platform hardware acl accounting
To display ACL accounting statistics, use the show platform hardware acl accounting command.
show platform hardware acl accounting {index {number | range number}} | interface {async number | auto-template number | ctunnel number | dialer number | esconphy number | filter number | filtergroup number | gigabitethernet number | longreachethernet number | loopback number | mfr number | multilink number | null number | port-channel number | portgroup number | pos-channel number | sysclock number | tengigabitethernet number | tunnel number | vif number | virtual-template number | virtual-tokenring number | vlan vlan_id | fcpa number | voabypassin number | voabypassout number | voafilterin number | voafilterout number | voain number | voaout number}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the ACL accounting statistics for VOA bypass-out interface number 4:
Router# show platform hardware acl accounting interface voabypassout 4Related Commands
platform hardware acl accounting
Configures platform hardware ACL accounting statistics for the available interfaces.
show platform hardware acl acct-xlt-tbl
To display ACL accounting tables, use the show platform hardware acl acct-xlt-tbl command.
show platform hardware acl acct-xlt-tbl {in {index {number | range number}} | out {index {number | range number}}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the accounting XLT entries that are sent outside the ACL:
Router# show platform hardware acl acct-xlt-tbl out indexRelated Commands
platform hardware acl acct-xlt-tbl
Configures platform hardware ACL accounting tables.
show platform hardware acl adj-rit
To display ACL TCAM adjacency entry information for various interfaces, use the show platform hardware acl adj-rit command.
show platform hardware acl adj-rit {interface {async number | auto-template number | ctunnel number | dialer number | esconphy number | filter number | filtergroup number | gigabitethernet number | longreachethernet number | loopback number | mfr number | multilink number | null number | port-channel number | portgroup number | pos-channel number | sysclock number | tengigabitethernet number | tunnel number | vif number | virtual-template number | virtual-tokenring number | vlan vlan_id | control-plane number | fcpa number | voabypassin number | voabypassout number | voafilterin number | voafilterout number | voain number | voaout number}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the adjacency entries for ACL asynchronous interface 4:
Router# show platform hardware acl adj-rit interface async 4Related Commands
platform hardware acl adj-rit
Configures ACL TCAM adjacency entry information for various interfaces.
show platform hardware acl capmap tcam
To display hardware ACL cap map entries for TCAM, use the show platform hardware acl capmap tcam command.
show platform hardware acl capmap tcam {A {index number | module number} | B {index number | module number}}
Syntax Description
A
Specifies entries in TCAM A.
B
Specifies entries in TCAM B.
index number
Specifies the cap map entry index number. Range is 0-2047.
module number
Specifies the module number.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the TCAM A cap map entry index number 20:
Router# show platform hardware acl capmap tcam A Index 20Related Commands
platform hardware acl capmap tcam
Configures platform hardware ACL cap map entries for TCAM.
show platform hardware acl config-registers
To display hardware classify block registers by module number, use the show platform hardware acl config-registers command.
show platform hardware acl config-registers {module number}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware classify block register for module 4:
Router# show platform hardware acl config-registers module 4Related Commands
platform hardware acl config-registers
Configures platform hardware ACL classify block registers by module number.
show platform hardware acl destinfo
To display hardware ACL destination information, use the show platform hardware acl destinfo command.
show platform hardware acl destinfo {in {index number | module number} | out {index number | module number} | module number}
Syntax Description
in
Specifies the inbound entries.
index number
Displays the entry index number. Range is 0-511.
module number
Displays the module number.
out
Specifies the outbound entries.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the ACL destination information for inbound entries in module 4:
Router# show platform hardware acl destinfo in module 4Related Commands
platform hardware acl destinfo
Configures platform hardware ACL destination information.
show platform hardware acl diagnostics
To display hardware ACL diagnostics reserved labels and indices by module number, use the show platform hardware acl diagnostics command.
show platform hardware acl diagnostics {module number}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware ACL diagnostics for module 4:
Router# show platform hardware acl diagnostics module 4Related Commands
platform hardware acl diagnostics
Configures platform hardware ACL diagnostics by module number.
show platform hardware acl entry
To display various ACL entries, use the show platform hardware acl entry command.
show platform hardware acl entry {compaction {module number}} | global-qos {in {arp {detail | module number} | ip {detail | module number} | ipv6 {detail | module number} | mac {detail | module number} | mpls {detail | module number}} | out {arp {detail | module number} | ip {detail | module number} | ipv6 {detail | module number} | mac {detail | module number} | mpls {detail | module number}} | interface {async number | auto-template number | ctunnel number | dialer number | esconphy number | filter number | filtergroup number | gigabitethernet number | longreachethernet number | loopback number | mfr number | multilink number | null number | port-channel number | portgroup number | pos-channel number | sysclock number | tengigabitethernet number | tunnel number | vif number | virtual-template number | virtual-tokenring number | vlan vlan_id | control-plane number | cts-reflector number | fcpa number | voabypassin number | voabypassout number | voafilterin number | voafilterout number | voain number | voaout number}} | rbacl {all {module number} | default {ip {module number} | ipv6 {module number}} | tcam {A {all {module number} | index number} | B {all {module number} | index number}}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the global QoS inbound ACL detailed entries for ARP protocol module 4:
Router# show platform hardware acl entry global-qos in arp detail module 4Related Commands
show platform hardware acl ethertype-cam
To display hardware ACL Ethertype CAM table by module number, use the show platform hardware acl ethertype-cam command.
show platform hardware acl ethertype-cam {module number}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware ACL Ethertype CAM table for module 4:
Router# show platform hardware acl ethertype-cam module 4Related Commands
platform hardware acl ethertype-cam
Configures platform hardware ACL Ethertype CAM table by module number.
show platform hardware acl hardware-hits
To display the TCAM hardware hits count, use the show platform hardware acl hardware-hits command.
show platform hardware acl hardware-hits {clear {module number} | show {module number}}
Syntax Description
clear
Displays the cleared hardware hits.
show
Displays the hardware hits since last clear.
module number
Specifies the module number.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the TCAM hardware hits cleared for module 4:
Router# show platform hardware acl hardware-hits clear 4Related Commands
show platform hardware acl initiate-lookup
To display ACL TCAM entries matching a pattern on available labels and interfaces, use the show platform hardware acl initiate-lookup command.
show platform hardware acl initiate-lookup {interface {async number | auto-template number | ctunnel number | dialer number | esconphy number | filter number | filtergroup number | gigabitethernet number | longreachethernet number | loopback number | mfr number | multilink number | null number | port-channel number | portgroup number | pos-channel number | sysclock number | tengigabitethernet number | tunnel number | vif number | virtual-template number | virtual-tokenring number | vlan vlan_id | fcpa number | voabypassin number | voabypassout number | voafilterin number | voafilterout number | voain number | voaout number} | label value tcam {A {arp {arp-rarp | arp_rarp_vld | global_acl_fmt_match | l2_miss | mac_da_bcast | mac_sa | ofe mode | req-rpl | sender_ip | src_snd_mac_same | src_tar_mac_same | target_ip | test} | ipv4 {acos | dst_port | first_seen [rp_bit] | frag_flag | ip_da | ip_frag | ip_sa | l4_proto | l4op | module | src_dst_as_num | src_port} | ipv6 {acos | dst_port | first_seen [rp_bit] | frag_flag | ip_da | ip_frag | ip_sa | l4_proto | l4op | module | src_dst_as_num | src_port} | l2 {acos | ce_vlan | dscp| enc | first_seen [rp_bit] | gpid | l2_miss | mac_da | mac_sa | module | vlan vlan_id} | mpls {acos | acos_gpid | exception | first_seen [rp_bit] | gpid_present | ip_hdr_vld | l2_miss | l4op | module | mpls_exp | mpls_exp_from_null | mpls_exp_of_null | mpls_label | mpls_mcast | mpls_stack | mpls_subtype | mpls_valid | u_key}} | B {arp {arp-rarp | arp_rarp_vld | global_acl_fmt_match | l2_miss | mac_da_bcast | mac_sa | ofe mode | req-rpl | sender_ip | src_snd_mac_same | src_tar_mac_same | target_ip | test} | ipv4 {acos | dst_port | first_seen [rp_bit] | frag_flag | ip_da | ip_frag | ip_sa | l4_proto | l4op | module | src_dst_as_num | src_port} | ipv6 {acos | dst_port | first_seen [rp_bit] | frag_flag | ip_da | ip_frag | ip_sa | l4_proto | l4op | module | src_dst_as_num | src_port} | l2 {acos | ce_vlan | dscp| enc | first_seen [rp_bit] | gpid | l2_miss | mac_da | mac_sa | module | vlan vlan_id} | mpls {acos | acos_gpid | exception | first_seen [rp_bit] | gpid_present | ip_hdr_vld | l2_miss | l4op | module | mpls_exp | mpls_exp_from_null | mpls_exp_of_null | mpls_label | mpls_mcast | mpls_stack | mpls_subtype | mpls_valid | u_key}}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the ACL TCAM entries matching a pattern on the asynchronous interface 4:
Router# show platform hardware acl initiate-lookup interface async 4Related Commands
platform hardware acl initiate-lookup
Configures ACL TCAM entries matching a pattern on available labels and interfaces.
show platform hardware acl label2sel tcam
To display label Layer 2 select entries for TCAM, use the show platform hardware acl label2sel tcam command.
show platform hardware acl label2sel tcam {A {index number} | B {index number}}
Syntax Description
A
Specifies label Layer 2 entries in TCAM A.
B
Specifies label Layer 2 entries in TCAM B.
index number
Specifies the TCAM index number. Range is 0-8191.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the TCAM A capmap entry index number 20:
Router# show platform hardware acl capmap tcam A Index 20Related Commands
platform hardware acl capmap tcam
Configures platform hardware ACL capmap entries for TCAM.
show platform hardware acl lou
To display the content of ACL logical operator units, use the show platform hardware acl lou command.
show platform hardware acl lou {index number | module number}
Syntax Description
index number
Specifies the LOU index number. Range is 0-103.
module number
Specifies the module number.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the ACL logical operator units for module 4:
Router# show platform hardware acl lou module 4Related Commands
show platform hardware acl status
To display hardware ACL status by module number, use the show platform hardware acl status command.
show platform hardware acl status {module number}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware ACL status for module 4:
Router# show platform hardware acl status module 4Related Commands
platform hardware acl status
Configures platform hardware ACL status by module number.
show platform hardware acl tcam
To display hardware ACL TCAM-related information, use the show platform hardware acl tcam command.
show platform hardware acl tcam {A {arp {accounting {module number} | module number | qos {module number} | security {module number}} | index number | ip {accounting {module number} | module number | qos {module number} | security {module number}} | ipv6 {accounting {module number} | module number | qos {module number} | security {module number}} | l2v4 {accounting {module number} | module number | qos {module number} | security {module number}} | mac {accounting {module number} | module number | qos {module number} | security {module number}} | module number | mpls {accounting {module number} | module number | qos {module number} | security {module number}}}
show platform hardware acl tcam {B {arp {accounting {module number} | module number | qos {module number} | security {module number}} | index number | ip {accounting {module number} | module number | qos {module number} | security {module number}} | ipv6 {accounting {module number} | module number | qos {module number} | security {module number}} | l2v4 {accounting {module number} | module number | qos {module number} | security {module number}} | mac {accounting {module number} | module number | qos {module number} | security {module number}} | module number | mpls {accounting {module number} | module number | qos {module number} | security {module number}}}
show platform hardware acl tcam {module number | result}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the TCAM A ARP accounting entries for module 4:
Router# show platform hardware acl tcam A arp accounting module 4Related Commands
show platform hardware acl tcp-flags-tbl
To display information about hardware ACL TCP flags, use the show platform hardware acl tcp-flags-tbl command.
show platform hardware acl tcp-flags-tbl {detail | index number | module number}
Syntax Description
detail
Displays TCP flags table details.
index number
Specifies the TCP flag index number. Range is 0-255.
module number
Specifies the TCP flag module number.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the ACL TCP flags for module 4:
Router# show platform hardware acl tcp-flags-tbl module 4Related Commands
show platform hardware acl v6-extnhdr-tbl
To display information about hardware ACL v6 extension header table, use the show platform hardware acl v6-extnhdr-tbl command.
show platform hardware acl v6-extnhdr-tbl {detail | index number | module number}
Syntax Description
detail
Displays extension header table details.
index number
Specifies the extension header table index number. Range is 0-127.
module number
Specifies the extension header table module number.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware ACL v6 extension header table information for module 4:
Router# show platform hardware acl v6-extnhdr-tbl module 4Related Commands
platform hardware acl v6-extnhdr-tbl
Configures hardware ACL v6 extension header tables.
show platform hardware asicreg
To display hardware ASIC register-related information, use the show platform hardware asicreg command.
show platform hardware asicreg {dhanush {slot number} | hyperion | medusa | mii-phy | palladium {get virtual_address | set virtual_address | all} | pentamak | ppc {all} | qchip | rchip | revati | santa-ana | sculptor | scuti | solano | supersantaana | vishakha}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display ASIC register information for the Dhanush ASIC, slot 4:
Router# show platform hardware asicreg dhanush slot 4Related Commands
show platform hardware asic-versions
To display hardware ASIC versions by slot number, use the show platform hardware asic-versions command.
show platform hardware asic-versions {slot number}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware ASIC version for slot number 4:
Router# show platform hardware asic-versions slot 4Related Commands
platform hardware asic-versions
Configures platform hardware ASIC versions by slot number.
show platform hardware capacity
To display the capacities and utilizations for the hardware resources, use the show platform hardware capacity command in privileged EXEC mode.
show platform hardware capacity [resource-type]
Syntax Description
resource-type
(Optional) Hardware resource type; see the "Usage Guidelines" section for the valid values.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
The valid values for resource-type are as follows:
•
acl—Displays the capacities and utilizations for ACL or QoS TCAM resources.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The show platform hardware capacity cpu command displays the following information:
•
•
•
The show platform hardware capacity eobc command displays the following information:
•
•
•
The show platform hardware capacity forwarding command displays the following information:
•
•
•
•
•
•
The show platform hardware capacity interface command displays the following information:
•
•
The show platform hardware capacity monitor command displays the following SPAN information:
•
•
The show platform hardware capacity multicast command displays the following information:
•
•
•
The show platform hardware capacity system command displays the following information:
•
•
•
–
–
–
The show platform hardware capacity vlan command displays the following VLAN information:
•
•
•
•
•
Examples
This example shows how to display CPU capacity and utilization information for the route processor, the switch processor, and the LAN module in the Cisco 7600 series router:
Router# show platform hardware capacity cpuCPU ResourcesCPU utilization: Module 5 seconds 1 minute 5 minutes1 RP 0% / 0% 1% 1%1 SP 5% / 0% 5% 4%7 69% / 0% 69% 69%8 78% / 0% 74% 74%Processor memory: Module Bytes: Total Used %Used1 RP 176730048 51774704 29%1 SP 192825092 51978936 27%7 195111584 35769704 18%8 195111584 35798632 18%I/O memory: Module Bytes: Total Used %Used1 RP 35651584 12226672 34%1 SP 35651584 9747952 27%7 35651584 9616816 27%8 35651584 9616816 27%Router#This example shows how to display EOBC-related statistics for the route processor, the switch processor, and the DFCs in the Cisco 7600 series router:
Router# show platform hardware capacity eobcEOBC ResourcesModule Packets/sec Total packets Dropped packets1 RP Rx: 61 108982 0Tx: 37 77298 01 SP Rx: 34 101627 0Tx: 39 115417 07 Rx: 5 10358 0Tx: 8 18543 08 Rx: 5 12130 0Tx: 10 20317 0Router#This example shows how to display the current and peak switching utilization:
Router# show platform hardware capacity fabricSwitch Fabric ResourcesBus utilization: current is 100%, peak was 100% at 12:34 12mar45Fabric utilization: ingress egressModule channel speed current peak current peak1 0 20G 100% 100% 12:34 12mar45 100% 100% 12:34 12mar451 1 20G 12% 80% 12:34 12mar45 12% 80% 12:34 12mar454 0 20G 12% 80% 12:34 12mar45 12% 80% 12:34 12mar4513 0 8G 12% 80% 12:34 12mar45 12% 80% 12:34 12mar45Router#This example shows how to display information about the total capacity, the bytes used, and the percentage that is used for the flash or NVRAM resources present in the system:
Router# show platform hardware capacity flashFlash/NVRAM ResourcesUsage: Module Device Bytes: Total Used %Used1 RP bootflash: 31981568 15688048 49%1 SP disk0: 128577536 105621504 82%1 SP sup-bootflash: 31981568 29700644 93%1 SP const_nvram: 129004 856 1%1 SP nvram: 391160 22065 6%7 dfc#7-bootflash: 15204352 616540 4%8 dfc#8-bootflash: 15204352 0 0%Router#This example shows how to display the capacity and utilization of the EARLs present in the system:
Router# show platform hardware capacity forwardingL2 Forwarding ResourcesMAC Table usage: Module Collisions Total Used %Used6 0 65536 11 1%VPN CAM usage: Total Used %Used512 0 0%L3 Forwarding ResourcesFIB TCAM usage: Total Used %Used72 bits (IPv4, MPLS, EoM) 196608 36 1%144 bits (IP mcast, IPv6) 32768 7 1%detail: Protocol Used %UsedIPv4 36 1%MPLS 0 0%EoM 0 0%IPv6 4 1%IPv4 mcast 3 1%IPv6 mcast 0 0%Adjacency usage: Total Used %Used1048576 175 1%Forwarding engine load:Module pps peak-pps peak-time6 8 1972 02:02:17 UTC Thu Apr 21 2005Netflow ResourcesTCAM utilization: Module Created Failed %Used6 1 0 0%ICAM utilization: Module Created Failed %Used6 0 0 0%Flowmasks: Mask# Type FeaturesIPv4: 0 reserved noneIPv4: 1 Intf FulNAT_INGRESS NAT_EGRESS FM_GUARDIANIPv4: 2 unused noneIPv4: 3 reserved noneIPv6: 0 reserved noneIPv6: 1 unused noneIPv6: 2 unused noneIPv6: 3 reserved noneCPU Rate Limiters ResourcesRate limiters: Total Used Reserved %UsedLayer 3 9 4 1 44%Layer 2 4 2 2 50%ACL/QoS TCAM ResourcesKey: ACLent - ACL TCAM entries, ACLmsk - ACL TCAM masks, AND - ANDOR,QoSent - QoS TCAM entries, QOSmsk - QoS TCAM masks, OR - ORAND,Lbl-in - ingress label, Lbl-eg - egress label, LOUsrc - LOU source,LOUdst - LOU destination, ADJ - ACL adjacencyModule ACLent ACLmsk QoSent QoSmsk Lbl-in Lbl-eg LOUsrc LOUdst AND OR ADJ6 1% 1% 1% 1% 1% 1% 0% 0% 0% 0% 1%Router#This example shows how to display the interboard communication resources:
Router# show platform hardware capacity ibcIBC ResourcesModule Packets/sec Total packets Dropped packets1 RP Rx: 3 5001419 0Tx: 1 1943884 0Router#This example shows how to display the interface resources:
Router# show platform hardware capacity interfaceInterface ResourcesInterface drops:Module Total drops: Tx Rx Highest drop port: Tx Rx9 0 2 0 48Interface buffer sizes:Module Bytes: Tx buffer Rx buffer1 12345 123455 12345 12345Router#This example shows how to display SPAN information:
Router# show platform hardware capacity monitorSPAN ResourcesSource sessions: 2 maximum, 0 usedType UsedLocal 0RSPAN source 0ERSPAN source 0Service module 0Destination sessions: 64 maximum, 0 usedType UsedRSPAN destination 0ERSPAN destination (max 24) 0Router#This example shows how to display the capacity and utilization of resources for Layer 3 multicast functionality:
Router# show platform hardware capacity multicastL3 Multicast ResourcesIPv4 replication mode: ingressIPv6 replication mode: ingressBi-directional PIM Designated Forwarder Table usage: 4 total, 0 (0%) usedReplication capability: Module IPv4 IPv65 egress egress9 ingress ingressMET table Entries: Module Total Used %Used5 65526 6 0%Router#This example shows how to display information about the system power capacities and utilizations:
Router# show platform hardware capacity powerPower ResourcesPower supply redundancy mode: administratively combinedoperationally combinedSystem power: 1922W, 0W (0%) inline, 1289W (67%) total allocatedPowered devices: 0 totalRouter#This example shows how to display the capacity and utilization of QoS policer resources per EARL in the Cisco 7600 series router:
Router# show platform hardware capacity qosQoS Policer ResourcesAggregate policers: Module Total Used %Used1 1024 102 10%5 1024 1 1%Microflow policer configurations: Module Total Used %Used1 64 32 50%5 64 1 1%Router#This example shows how to display information about the key system resources:
Router# show platform hardware capacity systemSystem ResourcesPFC operating mode: PFC3BXLSupervisor redundancy mode: administratively rpr-plus, operationally rpr-plusSwitching Resources: Module Part number Series CEF mode5 WS-SUP720-BASE supervisor CEF9 WS-X6548-RJ-45 CEF256 CEFRouter#This example shows how to display VLAN information:
Router# show platform hardware capacity vlanVLAN ResourcesVLANs: 4094 total, 10 VTP, 0 extended, 0 internal, 4084 freeRouter#Related Commands
show platform hardware capacity rewrite-engine
To display the packet drop and performance counters of the central rewrite engine on supervisor engines and line cards, use the show platform hardware capacity rewrite-engine command in privileged EXEC mode.
show platform hardware capacity rewrite-engine {drop | performance} [slot number] [rate [sample_interval]] [details]
Syntax Description
Defaults
If the sample interval is not specified, the default interval is 50 msec.
Command Modes
Privileged EXEC
Command History
Usage Guidelines
In the show platform hardware capacity rewrite-engine performance command output, a value of N/A indicates that the slot or channel has a rewrite engine, but does not support performance counters.
Examples
This example shows how to display the packet drop counters of the central rewrite engine in all installed supervisor engines and line cards:
Router# show platform hardware capacity rewrite-engine dropslot channel packet drops total overruns----+---------+-----------------+------------------+1 0 0 05 0 15440040 227 0 44 07 1 0 0This example shows how to display a detailed report of the packet drop counters of the module in slot 1:
Router# show platform hardware capacity rewrite-engine drop slot 1 detailsslot channel drop_id description packet drops total overruns----+-------+-------+--------------------+----------------+--------------+1 0 0x5ED DROP NON BPDU 0 01 0 0x5EB DROP BPDU 0 01 1 0x5ED DROP NON BPDU 0 01 1 0x5EB DROP BPDU 0 0This example shows how to display the packet drop counters of the module in slot 5 over the default sample interval of 50 msec:
Router# show platform hardware capacity rewrite-engine drop slot 5 rateslot channel drop rate [pps] overrun [Y/N]----+---------+----------------------+-------------+5 0 120079 YThis example shows how to display the packet drop counters of the module in slot 5 over a sample interval of 20 msec:
Router# show platform hardware capacity rewrite-engine drop slot 5 rate 20slot channel drop rate [pps] overrun [Y/N]----+---------+----------------------+-------------+5 0 180000 NThis example shows how to display the performance counters of the central rewrite engine in all installed supervisor engines and line cards:
Router# show platform hardware capacity rewrite-engine performanceslot channel perf_id description packets total overruns----+-------+-------+--------------------+----------------+--------------+1 0 0x235 FAB RX 0 12870 01 0 0x237 FAB RX 1 0 01 0 0x27B FAB TX 0 164 01 0 0x27F FAB TX 1 0 01 0 0x350 REPLICATION ML3 0 01 0 0x351 REPLICATION ML2 0 01 0 0x352 RECIRC L2 0 01 0 0x353 RECIRC L3 0 01 0 0x34C SPAN TX 0 0 01 0 0x34D SPAN TX 1 0 01 0 0x34E SPAN RX 0 0 01 0 0x34F SPAN RX 1 0 01 0 0x354 SPAN TERMINATION 0 01 1 0x235 FAB RX 0 106065 01 1 0x237 FAB RX 1 0 01 1 0x27B FAB TX 0 180806 01 1 0x27F FAB TX 1 0 01 1 0x350 REPLICATION ML3 0 01 1 0x351 REPLICATION ML2 0 01 1 0x352 RECIRC L2 0 01 1 0x353 RECIRC L3 0 01 1 0x34C SPAN TX 0 0 01 1 0x34D SPAN TX 1 0 01 1 0x34E SPAN RX 0 201 01 1 0x34F SPAN RX 1 90201 01 1 0x354 SPAN TERMINATION 0 04 0 N/A5 0 0xBE FAB RX 0 181496 05 0 0xC0 FAB RX 1 0 05 0 0x112 FAB TX 0 992089 05 0 0x116 FAB TX 1 0 05 0 0x299 REPLICATION ML3 0 05 0 0x29A REPLICATION ML2 0 05 0 0x29B RECIRC L2 0 05 0 0x29C RECIRC L3 0 05 0 0x295 SPAN TX 0 91166 05 0 0x296 SPAN TX 1 91313 05 0 0x297 SPAN RX 0 1 05 0 0x298 SPAN RX 1 1 05 0 0x29D SPAN TERMINATION 0 0This example shows how to display the performance counters of the module in slot 5:
Router# show platform hardware capacity rewrite-engine performance slot 5slot channel perf_id description packets total overruns----+-------+-------+--------------------+----------------+--------------+5 0 0xBE FAB RX 0 1330 05 0 0xC0 FAB RX 1 0 05 0 0x112 FAB TX 0 715253 05 0 0x116 FAB TX 1 0 05 0 0x299 REPLICATION ML3 0 05 0 0x29A REPLICATION ML2 0 05 0 0x29B RECIRC L2 0 05 0 0x29C RECIRC L3 0 05 0 0x295 SPAN TX 0 1022 05 0 0x296 SPAN TX 1 1152 05 0 0x297 SPAN RX 0 1 05 0 0x298 SPAN RX 1 1 05 0 0x29D SPAN TERMINATION 0 0This example shows how to display the performance counters of the module in slot 5 over the default sample interval of 50 msec:
Router# show platform hardware capacity rewrite-engine performance slot 5 rateslot channel perf_id description packet rate[pps] overrun [Y/N]----+-------+-------+--------------------+----------------+--------------+5 0 0xBE FAB RX 0 11680 N5 0 0xC0 FAB RX 1 0 N5 0 0x112 FAB TX 0 11680 N5 0 0x116 FAB TX 1 0 N5 0 0x299 REPLICATION ML3 0 N5 0 0x29A REPLICATION ML2 0 N5 0 0x29B RECIRC L2 0 N5 0 0x29C RECIRC L3 0 N5 0 0x295 SPAN TX 0 5840 N5 0 0x296 SPAN TX 1 5840 N5 0 0x297 SPAN RX 0 0 N5 0 0x298 SPAN RX 1 0 N5 0 0x29D SPAN TERMINATION 0 NRelated Commands
clear platform hardware capacity rewrite-engine counter
Clears the packet drop and performance counters of the central rewrite engine on supervisor engines and line cards.
show platform hardware cbl
To display hardware CBL by slot number, use the show platform hardware cbl command.
show platform hardware cbl {slot number}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware CBL for slot 4:
Router# show platform hardware cbl slot 4Related Commands
show platform hardware cef mpls detail
To display MPLS CEF detail information use the show platform hardware cef mpls detail command in privileged EXEC mode.
show platform hardware cef mpls detail [earl earl-id | module mod-num] group {ip-addr [detail | verbose]}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
The show platform hardware cef mpls detail command displays detailed information about MPLS adjacency entries. For each adjacency, use the show platform hardware cef adjacencies entry command to display the MPLS adjacency information.
Examples
This example shows how to display the MPLS CEF hardware details for EARL 1:
Router# show platform hardware multicast routing ip group 226.1.1.1 detailshow platform hardware cef mpls detail earl 1Codes: M - mask entry, V - value entry, A - adjacency index, NR- no_route bitLS - load sharing count, RI - router_ip bit, DF: default bitCP - copy_to_cpu bit, AS: dest_AS_number, DGTv - dgt_valid bitDGT: dgt/others value, LS: load sharing count on eos conditionEE: EOS enable, NW: num swap paths, NP: num push pathsFormat:MPLS (valid class vpn_tbid vpn_vld Label0 M EoS Lif/Label1M(52740 ): 1 F 3FFF 1 FFFFF 0 1 0V(52740 ): 1 2 0 1 1 0 0 0(A:213012, LS:0, NR:0, RI:0, DF:0 CP:0 DGTv:0, DGT:0)M(52742 ): 1 F 3FFF 1 FFFFF 0 1 0V(52742 ): 1 2 0 1 1 0 1 0(A:78089 , LS:0, NR:0, RI:0, DF:0 CP:0 DGTv:0, DGT:0)M(52822 ): 1 F 3FFF 1 FFFFF 0 1 0V(52822 ): 1 2 0 1 21 0 1 0(A:213013, LS:0, NR:0, RI:0, DF:0 CP:0 DGTv:0, DGT:0)M(52830 ): 1 F 3FFF 1 FFFFF 0 1 0V(52830 ): 1 2 0 1 23 0 1 0(A:213017, LS:0, NR:0, RI:0, DF:0 CP:0 DGTv:0, DGT:0)M(52834 ): 1 F 3FFF 1 FFFFF 0 1 0V(52834 ): 1 2 0 1 24 0 1 0Router#Related Commands
show platform hardware cef adjacencies entry
To display a single adjacency entry index, use the show platform hardware cef adjacencies entry command in privileged EXEC mode
show platform hardware cef adjacencies entry entry-num
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display the index for CEF adjacency 45:
Router# show platform hardware cef adjacencies entry 45Index: 45 -- Valid entry (valid = 1) --Adjacency fields:___________________________________________________|adj_stats = EN | fwd_stats = EN | format = IP|_________________|__________________|______________|rdt = OFF | elif = 0x2D | vpn = 0x3FFF|_________________|__________________|______________RIT fields: The entry has a Recirc. Format_________________________________________________________|decr_ttl=NO | l2_fwd=YES | ccc = 4 | add_shim_hdr = NO|_____________|____________|_________|____________________Statistics: Packets = 0Bytes = 0Router#Related Commands
show platform hardware cef tcam
To display platform hardware Cisco Express Forwarding (CEF) Forwarding Information Base (FIB) Ternary Content Addressable Memory (TCAM), use the show platform hardware cef command.
show platform hardware cef tcam {ecc [detail [earl earl-id] | module module-num]| earl earl-id]| module module-num]| hit [detail [earl earl-id] | module module-num]| earl earl-id]| module module-num]| keys [count | exception ]| memory usage | segment [detail [earl earl-id] | module module-num]| earl earl-id]| module module-num] | select [detail [earl earl-id] | module module-num]| earl earl-id]| module module-num] | shadow [detail [earl earl-id] | module module-num]| earl earl-id]| module module-num] | timing [detail [earl earl-id] | module module-num]| earl earl-id]| module module-num] | utilization [detail [earl earl-id] | module module-num]| earl earl-id]| module module-num]| earl earl-id] | module module-num]
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
12.2(33)SX
Support for this command was introduced.
15.1(1)SY
Added ecc, key, memory, segment, select, shadow, timing, and utilization keywords.
Examples
This example shows how to display the hardware CEF TCAM key exception:
Router(config)# show platform hardware cef tcam keys exception
Priorities in exception:
Class ID Pri (>=) Max Key-Cnt Pri-Cnt
IPv4 0 16 35 35085
IPv4-Mcast 1 68 68 0
MPLS 2 17 17 0
EOMPLS 3 19 19 0
MPLS-VPN 4 9 9 0
Diags 5 5 5 0
IPv6-Local 6 390 390 0
IPv6-Mcast 7 261 261 0
IPv6-Global 8 244 390 1051
VPLSv4-Mcast 9 69 69 0
VPLSv6-Mcast 10 261 261 0
Keys in each Pri in exception:
Class ID Pri XCP Pri-Cnt
IPv4 0 16 4096
. . 17 15507
. . 18 7753
. . 19 3876
. . 20 1939
. . 21 969
. . 22 484
. . 23 243
. . 24 121
. . 25 60
. . 26 34
. . 30 2
. . 34 1
IPv6-Global 8 244 129
. . 245 126
. . 246 118
. . 247 114
. . 248 111
. . 249 109
. . 250 109
. . 251 107
. . 252 64
. . 253 32
. . 254 16
. . 255 8
. . 256 4
. . 257 2
. . 389 1
. . 390 1
Spanslogic#show platform hardware cef tcam memory usage
Buffer allocation summary:
Data Page Total Total Used Used Free Free
Id Size Size Count Size Count Size Count Size Type
0 0 0 0 0 0 0 0 0 Void
1 80 80 0 0 0 0 0 0 Bsort
2 2076 65536 279 576K 0 0 279 565K Bsort Node
3 3456 65536 288 1.00M 20 39744 268 904K Bsort Stat
4 60 65536 2184 128K 1697 99.4K 487 29220 Wsort Seg
5 104 65536 630 65536 17 1768 613 63752 Wsort Win
6 1024 65536 384 384K 17 17408 367 367K Wsort Avail
7 3644 3644 3 10932 3 10932 0 0 Group
8 324 8192 25 8192 20 6480 5 1620 Group Entry
9 0 0 2 20480 2 20480 0 0 SE Block
10 4104 65536 3660 15.2M 2814 11.1M 846 3.31M SE Slice
11 52 65536 2520 128K 1697 88244 823 42796 SE Seg
12 68 65536 18297 1.18M 0 0 18297 1.18M SE Rec
13 0 0 0 0 0 0 0 0 SE Pri
14 48 65536 619k 28.3M 587k 26.8M 32320 1.47M Key
15 8 65536 0 0 0 0 0 0 Bit 64
16 12 65536 1.20m 13.7M 1.13m 13.2M 63352 742K Bit 96
17 16 65536 0 0 0 0 0 0 Bit 128
18 20 65536 39312 768K 36634 715K 2678 53560 Bit 160
19 24 24 0 0 0 0 0 0 Bit 192
20 28 28 0 0 0 0 0 0 Bit 224
21 32 65536 8192 256K 5628 175K 2564 82048 Bit 256
22 36 65536 0 0 0 0 0 0 Bit 288
23 40 65536 1638 65536 98 3920 1540 61600 Bit 320
24 44 44 0 0 0 0 0 0 Bit 352
25 48 48 0 0 0 0 0 0 Bit 384
26 52 52 0 0 0 0 0 0 Bit 416
27 56 56 0 0 0 0 0 0 Bit 448
28 60 65536 0 0 0 0 0 0 Bit 480
29 64 64 0 0 0 0 0 0 Bit 512
30 68 68 0 0 0 0 0 0 Bit 544
31 72 72 0 0 0 0 0 0 Bit 576
32 76 76 0 0 0 0 0 0 Bit 608
33 80 65536 0 0 0 0 0 0 Bit 640
34 84 84 0 0 0 0 0 0 Bit 672
35 88 88 0 0 0 0 0 0 Bit 704
* * * 1.89m 61.9M 1.77m 52.7M 124k 8.81M Total
Router(config)#
This example shows how to display the hardware CEF TCAM timing information:
Router(config)# show platform hardware cef tcam timing
(0) Groom Clock: 182us (Min) << 71ms (Avg) << 404ms (Max) = 09.19s (Tot)
5.28ms 1.16ms 10ms 38ms 3.43ms 10ms 166ms 223ms
5.06ms 960us 9.34ms 37ms 1.79ms 96ms 110ms 155ms
4.72ms 1.06ms 8.90ms 34ms 813us 4.14ms 110ms 138ms
4.12ms 755us 6.81ms 32ms 305us 75ms 28ms 237ms
3.90ms 690us 6.13ms 30ms 228us 50ms 247ms 199ms
3.67ms 529us 5.81ms 28ms 274us 94ms 217ms 63ms
3.38ms 506us 3.68ms 25ms 1.73ms 269ms 218ms 96ms
3.14ms 400us 2.94ms 23ms 279us 119ms 277ms 66ms
2.94ms 351us 3.63ms 20ms 115ms 163ms 346ms 94ms
2.87ms 306us 2.75ms 18ms 46ms 404ms 316ms 35ms
2.76ms 291us 1.18ms 16ms 156ms 351ms 154ms 84ms
3.30ms 275us 794us 13ms 87ms 319ms 220ms 5.51ms
5.20ms 202us 736us 11ms 8.52ms 85ms 220ms 203ms
2.77ms 190us 39ms 9.58ms 112ms 229ms 189ms 191ms
1.58ms 182us 39ms 7.52ms 73ms 180ms 172ms 216ms
1.84ms 11ms 38ms 5.63ms 90ms 188ms 227ms 1.27ms
(1) Add Clock: 11us (Min) << 13us (Avg) << 107us (Max) = 1.78ms (Tot)
11us 11us 11us 12us 11us 12us 12us 12us
11us 12us 12us 11us 11us 11us 11us 12us
12us 11us 12us 12us 11us 12us 12us 12us
12us 12us 12us 12us 11us 12us 12us 13us
11us 12us 12us 12us 11us 11us 11us 12us
12us 12us 12us 12us 11us 12us 12us 12us
12us 12us 11us 12us 11us 11us 11us 12us
11us 11us 12us 11us 11us 12us 12us 12us
11us 12us 11us 11us 11us 12us 11us 11us
12us 12us 12us 11us 11us 11us 11us 40us
107us 12us 12us 12us 12us 12us 12us 41us
12us 11us 11us 12us 12us 12us 11us 40us
12us 12us 11us 12us 12us 11us 11us 40us
11us 11us 12us 12us 12us 12us 11us 40us
12us 12us 12us 12us 12us 11us 12us 40us
12us 12us 11us 11us 11us 12us 12us 40us
Router(config)#
This example shows how to display the hardware CEF TCAM utilization information:
Router(config)# show platform hardware cef tcam utilization
Util summary for Pool 0: 524288 keys, 1024 segs, 36 MbType KeyCnt KeyUse SegCnt SegUse Util Free0 463704 463704 909 909 99 1151 0 0 0 0 0 1152 0 0 0 0 0 573 0 0 0 0 0 294 0 0 0 0 0 28Tot 463704 463704 909 909 99 115Util summary for Pool 1: 524288 keys, 1024 segs, 36 MbType KeyCnt KeyUse SegCnt SegUse Util Free0 105327 105327 208 208 98 8031 9 18 7 7 0 8032 46 184 3 6 5 3913 0 0 0 0 0 1914 0 0 0 0 0 189Tot 105382 105529 218 221 93 803Util summary for Pool 8: 1048576 keys, 2048 segs, 72 MbType KeyCnt KeyUse SegCnt SegUse Util Free0 569031 569031 1117 1117 99 9181 9 18 7 7 0 9182 46 184 3 6 5 4483 0 0 0 0 0 2204 0 0 0 0 0 217Tot 569086 569233 1127 1130 98 918Related Commands
clear platform hardware cef adjacencies
Clears platform hardware CEF adjacencies.
show platform hardware cef adjacencies
To display platform hardware Cisco Express ForwardingCEF adjacencies, use the show platform hardware cef adjacencies command.
show platform hardware cef adjacencies all {detail {module {module number}
show platform hardware cef adjacencies allocation-map {number | module {module number}}
show platform hardware cef adjacencies decap-tunnel {detail {module {module number}}}
show platform hardware cef adjacencies earl {earl-id}
show platform hardware cef adjacencies encap-tunnel {A.B.C.D | {detail {module {module number}
show platform hardware cef adjacencies entry number | errors {module}
show platform hardware cef adjacencies mac-address {h.h.h.}
show platform hardware cef adjacencies mac-rewrite {detail | module}
show platform hardware cef adjacencies module
show platform hardware cef adjacencies mpls {detail | module}
show platform hardware cef adjacencies multicast {detail | module}
show platform hardware cef adjacencies nat {detail | module }
show platform hardware cef adjacencies recirculation {detail | module}
show platform hardware cef adjacencies resource-level
show platform hardware cef adjacencies special {module}
show platform hardware cef adjacencies status {number | module}
show platform hardware cef adjacencies tcp-intercept {detail | module}
show platform hardware cef adjacencies usage {decap-tunnel | encap-tunnel | mac-rewrite | module | mpls | multicast | nat | recirculation |tcp-intercept}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the CEF adjacencies allocation map module number:
Router# show platform hardware cef adjacencies allocation-map module 4This example shows how to display the CEF adjacencies status allocated or used starting at entry 100:
Router# show platform hardware cef adjacencies status 100Hardware Adjacencies used or allocated entries:Users: "fib-ucast-v4" "fib-ucast-v6" "mpls" "vpls-ucast""fib-mcast" "vpls-mcast" "acl-feature" "netflow-feat""online-diag" "adjacency-mgr" "exceptions"------------------------------------------------------Index Owner Status Time80128 netflow-feat Allocated *Jun 21 23:56:25.28780129 netflow-feat Allocated *Jun 21 23:56:25.28780130 netflow-feat Allocated *Jun 21 23:56:25.28780131 netflow-feat Allocated *Jun 21 23:56:25.28780132 netflow-feat Allocated *Jun 21 23:56:25.28780133 netflow-feat Allocated *Jun 21 23:56:25.28780134 netflow-feat Allocated *Jun 21 23:56:25.28780135 netflow-feat Allocated *Jun 21 23:56:25.28780136 netflow-feat Allocated *Jun 21 23:56:25.28780137 netflow-feat Allocated *Jun 21 23:56:25.28780138 netflow-feat Allocated *Jun 21 23:56:25.28780139 netflow-feat Allocated *Jun 21 23:56:25.28780140 netflow-feat Allocated *Jun 21 23:56:25.28780141 netflow-feat Allocated *Jun 21 23:56:25.28780142 netflow-feat Allocated *Jun 21 23:56:25.28780143 netflow-feat Allocated *Jun 21 23:56:25.28780144 netflow-feat Allocated *Jun 21 23:56:25.28780145 netflow-feat Allocated *Jun 21 23:56:25.28780146 netflow-feat Allocated *Jun 21 23:56:25.28780147 netflow-feat Allocated *Jun 21 23:56:25.28780148 netflow-feat Allocated *Jun 21 23:56:25.28780149 netflow-feat Allocated *Jun 21 23:56:25.28780150 netflow-feat Allocated *Jun 21 23:56:25.28780151 netflow-feat Allocated *Jun 21 23:56:25.28780152 netflow-feat Allocated *Jun 21 23:56:25.28780153 netflow-feat Allocated *Jun 21 23:56:25.28780154 netflow-feat Allocated *Jun 21 23:56:25.28780155 netflow-feat Allocated *Jun 21 23:56:25.28780156 netflow-feat Allocated *Jun 21 23:56:25.28780157 netflow-feat Allocated *Jun 21 23:56:25.28780158 netflow-feat Allocated *Jun 21 23:56:25.28780159 netflow-feat Allocated *Jun 21 23:56:25.28780160 netflow-feat Allocated *Jun 21 23:56:25.28780161 netflow-feat Allocated *Jun 21 23:56:25.28780162 netflow-feat Allocated *Jun 21 23:56:25.28780163 netflow-feat Allocated *Jun 21 23:56:25.28780164 netflow-feat Allocated *Jun 21 23:56:25.28780165 netflow-feat Allocated *Jun 21 23:56:25.28780166 netflow-feat Allocated *Jun 21 23:56:25.28780167 netflow-feat Allocated *Jun 21 23:56:25.28780168 netflow-feat Allocated *Jun 21 23:56:25.28780169 netflow-feat Allocated *Jun 21 23:56:25.28780170 netflow-feat Allocated *Jun 21 23:56:25.28780171 netflow-feat Allocated *Jun 21 23:56:25.28780172 netflow-feat Allocated *Jun 21 23:56:25.287Router#Related Commands
clear platform hardware cef adjacencies
Clears platform hardware CEF adjacencies.
show platform hardware cef maximum-route
To display Cisco Express Forwarding (CEFv6) maximum routes, use the show platform hardware cef maximum-routes command in Privileged EXEC mode. This command displays both the maximum routes configuration and the current usage of entries within the dedicated area and the shared area.
show platform hardware cef maximum-routes {usage}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display CEFv6 maximum routes configuration and the current usage of entries within the dedicated area and the shared area:
Router#show platform hardware cef maximum-routesFib-size: 256k (262144), shared-size: 25k (25600), shared-usage: 0k(0)Protocol Max-routes Use-shared-region Dedicated-------- ---------- ----------------- ---------IPV4 217 k Yes 192kIPV4-MCAST 4 k No 4kIPV6 35 k Yes 10kIPV6-MCAST 6 k No 6kMPLS 5 k No 5kMPLS-VPN 3 k No 3kEoMPLS 3 k No 3kVPLS-IPV4-MCAST 4 k No 4kVPLS-IPV6-MCAST 4 k No 4kThis example shows how to display CEFv6 accounting prefix statistics:Router(config)#show platform hardware cef maximum-routes usageFib-size: 256k (262144), shared-size: 25k (25600), shared-usage: 0k(0)Protocol Max-routes Usage Usage-from-shared------- ---------- ----- -----------------IPV4 217 k 48 (0 k) 0 (0 k)IPV4-MCAST 4 k 6 (0 k) 0 (0 k)IPV6 35 k 2 (0 k) 0 (0 k)IPV6-MCAST 6 k 4 (0 k) 0 (0 k)MPLS 5 k 1 (0 k) 0 (0 k)MPLS-VPN 3 k 0 (0 k) 0 (0 k)EoMPLS 3 k 2 (0 k) 0 (0 k)VPLS-IPV4-MCAST 4 k 0 (0 k) 0 (0 k)VPLS-IPV6-MCAST 4 k 0 (0 k) 0 (0 k)Router#Related Commands
platform hardware cef maximum-route
Limits the maximum number of routes that can be programmed in the hardware.
show platform hardware database version
To display the platform hardware database version, use the show platform hardware database command.
show platform hardware database version [slot slot_number]
Syntax Description
slot slot_number
Specifies the slot number of a module that has hardware abstraction layer (HAL) support.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
12.2(50)SY
Support for this command was introduced.
15.0(1)SY1
The slot keyword and slot_number argument were added.
Usage Guidelines
The show platform hardware database command displays the following Supervisor Engine 2T platform hardware database version:
•
•
•
•
•
•
The flash region has three states:
•
•
•
Note
The slot keyword is supported only on modules that have hardware abstraction layer (HAL) support.
Examples
This example shows how to display the platform hardware database version:
Router# show platform hardware database versionHardware database image bundle version: 2.1.0Description: Hardware database release 2.1.0Hardware database flash version from region S (Gold): 0.19.23Hardware database runtime using image bundle version: 2.1.0Region F1: INVALIDRegion F2: INVALIDRegion S (Golden): Version: 0.19.23Description: change slot 7 from le_adaptive to le_gain (le_fixed)Related Commands
show platform hardware earl
To display platform hardware EARL information, use the show platform hardware earl command.
show platform hardware earl {cc {table {agegrp {entry {entry number}} | bem {entry {entry number}} | bpm {entry {entry number}} | glblvlan {entry {entry number}}}} | earl_db | eureka | lamira | layer2 | wf-fpga}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the EARL consistency checker age group entry 4444:
Router(config)# show platform hardware earl cc table agegrp entry 4444
Related Commands
show platform hardware earl eureka
To display platform hardware EARL Eureka ASIC information, use the show platform hardware earl eureka command.
show platform hardware earl eureka config {all {file {word}} | module {ac {dbi | epp | ft | l2u | l2ui | l3lu | l3lu312 | l3mg | lif | lm_rx | lm_tx | ntfy | pb1_rx | pb1_tx | pb2_rx | pb2_tx | pp | rbi } | dbi | epp | ft | l2u | l2ui | l3lu | l3lu312 | l3mg | lif | lm_rx | lm_tx | ntfy | pb1_rx | pb1_tx | pb2_rx | pb2_tx | pp | rbi}}
show platform hardware earl eureka ecc {configuration {all | table {eu-acl0 | eu-acl1 | ft | lb | ldb | lifdb | lifstat | rbi}} | statistics {all | table {eu-acl0 | eu-acl1 | ft | lb | ldb | lifdb | lifstat | rbi}}}
show platform hardware earl eureka interupts {all {file {word}} | clear {all {file} | module} | module {ac | epp | ft | l2u | l2ui | l3lu | l3lu312 | l3mg | lif | lm_rx | lm_tx | ntfy | pb1_rx | pb1_tx | pb2_rx | pb2_tx | pp | rbi | se}}
show platform hardware earl eureka statistics {all {file} | clear {all | module} | module {ac | epp | ft | l2u | l2ui | l3lu | l3lu312 | l3mg | lif | lm_rx | lm_tx | ntfy | pb1_rx | pb1_tx | pb2_rx | pb2_tx | pp | rbi | se}}
show platform hardware earl eureka vsl {mapping-tables {pb1 {dst-post-map | dst-pre-map | src-pre-map}} | pb2} | registers}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display all of EARL Eureka ASIC configurations:
Router# show platform hardware earl eureka config all
Related Commands
clear platform hardware earl eureka
Clears platform hardware EARL Eureka ASIC information.
show platform hardware earl lamira
To display platform hardware EARL Lamira ASIC information, use the show platform hardware earl lamira command.
show platform hardware earl lamira {config {all {file {word}} | module {ci | cl1 | cl1_2 | cl2 | gv | if | l3 | la0 | la1 | nf | nf2 | nf_se | pl | pl2 | po | ri | rp}} | ecc {configuration {all | table {acct | aclsram-a | aclsram-b | acltcam-a | acltcam-b | acosseli | adj-dram | adjstats | agdpp | cmtbla | cmtblb | dagram | egmtmap | elifmap | fib-dram | fibtcam | ife_dstinfo | iferdt | ilifmap | infife | infofe | label2sela | label2selb | lcbcnt | nffl | nfhash0 | nfhash1 | nfstats | nftable | nfvram | ofe_dstinfo | ofeff | oferdt | outff | plcbas | pmap | rit | rpfdram | rwsel | sagram | smpl | srcdstas | vidmap | vlanmap}} | statistics {all | table {acct | aclsram-a | aclsram-b | acltcam-a | acltcam-b | acosseli | adj-dram | adjstats | agdpp | cmtbla | cmtblb | dagram | egmtmap | elifmap | fib-dram | fibtcam | ife_dstinfo | iferdt | ilifmap | infife | infofe | label2sela | label2selb | lcbcnt | nffl | nfhash0 | nfhash1 | nfstats | nftable | nfvram | ofe_dstinfo | ofeff | oferdt | outff | plcbas | pmap | rit | rpfdram | rwsel | sagram | smpl | srcdstas | vidmap | vlanmap}}} | interrupts {all {file {word}} |clear {all {file} | module {cl1 | cl1_2 | cl2 | gv | if | l3 | la0 | la1 | nf | nf2 | nf_se | pl | pl2 | po | ri | rp}} | module} | statistics {all {file {word}} | clear {all | module {ci | cl1 | cl1_2 | cl2 | gv | if | l3 | la0 | la1 | nf | nf2 | nf_se | pl | pl2 | po | ri | rp}} | module}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display all of the EARL Lamira ASIC configuration:
Router# show platform hardware earl lamira config all
Related Commands
clear platform hardware earl lamira
Clears platform hardware EARL Lamira ASIC information.
show platform hardware earl layer2
To display platform hardware EARL Layer 2 information, use the show platform hardware earl layer2 command.
show platform hardware earl layer2 {etherchannel {bem-table {number number} | bpm-table {bridge-domain number} | config} | forwarding-table {dump {all | l2addr number} | l2addr {H.H.H}} | redirections {protocol-filtering {dump {all | dot1ad | dot1q | vpls} | profile-map}}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display platform hardware EARL Layer 2 EtherChannel BPM table, bridge domain 4:
Router# show platform hardware earl layer2 etherchannel bpm-table bridge-domain 4Related Commands
platform hardware earl layer2
Configures the platform hardware EARL for Layer 2.
show platform hardware efp
To display hardware EFP configuration, use the show platform hardware efp command.
show platform hardware efp {config {gigabitethernet number | port-channel number | tengigabitethernet number} | datapath {gigabitethernet number | port-channel number | tengigabitethernet number} | global}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware EFP configuration information for Gigabit Ethernet 4:
Router# show platform hardware efp config gigabitethernet 4Related Commands
show platform hardware fan-tray
To display hardware fan tray status or details by number, use the show platform hardware fan-tray command.
show platform hardware fan-tray {number | status}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware details for fan tray 1:
Router# show platform hardware fan-tray 1Related Commands
show platform hardware flow table
To display hardware flow table entries, use the show platform hardware flow table command.
show platform hardware flow table {copy-policy index | flowmask {index | ip index | ipv6 index | l2 index | mpls index} | mark-en-map index | profile {index | ip index | ipv6 index | l2 index | mpls index} | qos-ctrl index | redirect {ife index | ofe index | tcp index} | sampler index | sampler-copy index | shadow {copy-policy index | flowmask {index | ip index | ipv6 index | l2 index | mpls index} | mark-en-map index | profile {index | ip index | ipv6 index | l2 index | mpls index} | qos-ctrl index | redirect {ife index | ofe index | tcp index} | sampler index | sampler-copy index}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware flow table entries for IFE redirect index 4:
Router# show platform hardware flow table redirect ife 4Related Commands
platform hardware flow table
Configures the platform hardware flow table entries.
show platform hardware fpoe
To display hardware Fabric Port of Exit (FPoE) by slot number, use the show platform hardware fpoe command.
show platform hardware fpoe {slot number}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the hardware FPoE for slot 4:
Router# show platform hardware fpoe slot 4Related Commands
show platform hardware idprom
To display information on EEPROM for the platform hardware, use the show platform hardware idprom command.
show platform hardware idprom {backplane number | clock number | earl number | fabric-extension number | fan-tray number | module number | power-supply number | rp number | supervisor number | vdb number | vtt number}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the information on the EEPROM for backplane 1:
Router# show platform hardware idprom backplane 1Related Commands
platform hardware idprom
Configures the information on the EEPROM for the platform hardware.
show platform hardware image version slot
To display the hardware abstraction layer (HAL) image version information, use the show platform hardware image version command.
show platform hardware image version slot number
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
This command is useful only if a new hardware image version becomes available.
This command is supported only on modules that have hardware abstraction layer (HAL) support.
Examples
This example shows how to display the HAL image version information for a module:
Router# show platform hardware image version slot 3Image bundle version: 1.1Linecard image version from region S(Golden): INVALIDImage runtime using image bundle version: 1.1Region F1: INVALID, version: INVALIDRegion S (Golden): version: INVALID
Note
Related Commands
show platform hardware lif l2
To display platform hardware Layer 2 LIF information, use the show platform hardware lif l2 command.
show platform hardware lif l2 {globalcfg | memory {memory detail} | region {adjacency {dti {adjacency number | config} | replicated {adjacency | config}} | egresslif {config | lif {lif number}} | flood{config | ltl} | globalvlan {config | vlan} | negative-mn {config | ltl} | portgroup{config | ltl} | shim {config | lif}| swltl {config | ltl} | vb{config | vlan}} | table {global-vlan vlan | lif-db {all | entry number | key} | port-map{all | interface {gigabitethernet | longreachethernet | multilink | port-channel | tengigabitethernet} | ltl-index number}}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display platform hardware Layer 2 LIF global configuration:
Router# show platform hardware lif l2 globalcfgRelated Commands
show platform hardware lif l3
To display platform hardware Layer 3 LIF information, use the show platform hardware lif l3 command.
show platform hardware lif l3 {egress {features | handle | hierarchy | index | interface | ipv4 | ipv6 | misc | module | mpls | qos} | info number | ingress { features | handle | hierarchy | index | interface | ipv4 | ipv6 | misc | module | mpls | qos} | mtu { table {dump | index}} | port-map{ index number | interface {gigabitethernet | port-channel | tengigabitethernet tunnel | vlan} | module number}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display platform hardware EARL Layer 3 LIF test number 4:
Router# show platform hardware lif l3 info 4Related Commands
show platform hardware lif stats
To display hardware LIF statistics, use the show platform hardware lif stats command.
show platform hardware lif stats {index number | interface {gigabitethernet | port-channel | tengigabitethernet | tunnel | vlan} | profile {choice {all {module} | id number} | read{module} | write number} | table {config {module} | egress {module} | fop {module} | ingress {module} | no-stat {module} | status {module}}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display platform hardware LIF statistics for index 4:
Router# show platform hardware lif stats index 4Related Commands
show platform hardware ltl
To display information on LTL for the platform hardware, use the show platform hardware ltl command.
show platform hardware ltl {index number | interface {gigabitethernet number | tengigabitethernet number} | slot number | vlan vlan_id}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the LTL information for Gigabit Ethernet 4:
Router# show platform hardware ltl interface gigabitethernet 4Related Commands
show platform hardware multicast routing
To match and display multicast routing entries in hardware for multicast IPv4 and IPv6 addresses, use the show platform hardware multicast routing command in privileged EXEC mode.
show platform hardware multicast routing {ip | ipv6} group {ip-addr [detail | verbose]}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
The show platform hardware multicast routing ip group command displays multicast OIFs.
Examples
This example shows how to display the hardware detail entries:
Router# show platform hardware multicast routing ip group 226.1.1.1 detail(10.1.1.1, 226.1.1.1/32)FIBAddr: 0xB00 IOSVPN: 0 RpfType: SglRpfChk SrcRpf: Gi1/1CPx: 0 s_star_pri: 1 non-rpf drop: 0PIAdjPtr: 0x30002 Format: IP rdt: off elif: 0xC5408fltr_en: off idx_sel/bndl_en: 0 dec_ttl: on mtu_idx: 2(1518)PV: 1 rwtype: MCAST_L3_RWT_L2_EXPSmet3: 0x19 met2: 0x18Packets: 0 Bytes: 0NPIAdjPtr: 0x30003 Format: IP rdt: on elif: 0xC5408fltr_en: off idx_sel/bndl_en: 0 dec_ttl: offPV: 0 rwtype: MCAST_L3_REWRITEmet3: 0x20 met2: 0x0 DestNdx: 0x7FF3Packets: 0 Bytes: 0MET offset: 0x19OIF AdjPtr Elif CR+-------------+----------+-----------+--------+EDT-50001 0x50001 0x8400A 1T1 5T1/T2MET offset: 0x20OIF AdjPtr Elif CR+-------------+----------+-----------+--------+Gi1/2 0xA8000 0xA4012 1T1MET offset: 0x18LBL IF AdjPtr Elif CR+-------------+----------+-------------+-----------+---------+20 Gi3/9 0xA8000 0xA4013 3T1/T2Router#This example shows how to display the hardware verbose entries:
Router# show platform hardware multicast routing ip group 226.1.1.1 verbose(10.0.0.2, 226.1.1.1/32)FIBAddr: 0x2A04 IOSVPN: 0 RpfType: SglRpfChk SrcRpf: Po1CPx: 0 s_star_pri: 1 non-rpf drop: 0PIAdjPtr: 0x30003 Format: IP rdt: off elif: 0xC5408fltr_en: off idx_sel/bndl_en: 0 dec_ttl: on mtu_idx: 2(1518)PV: 1 rwtype: MCAST_L3_RWT_L2_EXPSmet3: 0x18 met2: 0x18Packets: 31912689 Bytes: 15956344500NPIAdjPtr: 0x30004 Format: IP rdt: on elif: 0xC5408fltr_en: off idx_sel/bndl_en: 0 dec_ttl: offPV: 0 rwtype: MCAST_L3_REWRITEmet3: 0x5 met2: 0x0 DestNdx: 0x7FF3Packets: 1263 Bytes: 631500OIF: Vl9 OIFAdjPtr: 0x8009 Format: IP rdt: off elif: 0x9fltr_en: on idx_sel/bndl_en: 1 dec_ttl: offPV: 0 rwtype: L3_REWRITEsmac_rwt: 1 smac: 000e.39c2.b540 ip_to_mac: 1OIF: EDT-50001 OIFAdjPtr: 0x50001 Format: MDT rdt: on elif: 0x8400Afltr_en: off idx_sel/bndl_en: 1 dec_ttl: offPV: 0 rwtype: L3_REWRITE add_shim: 1rec_shim_op: DTI_FROM_RIT rec_dti_type: RSVD3 rec_data: 0x701A0000 eg_mcast_dist: 1DestNdx: 0x80D RBH: 0x0DestNdx: 0x80D RBH: 0x1DestNdx: 0x80D RBH: 0x2DestNdx: 0x80D RBH: 0x3DestNdx: 0x80D RBH: 0x4DestNdx: 0x80D RBH: 0x5DestNdx: 0x80D RBH: 0x6DestNdx: 0x80D RBH: 0x7LBL: 20 OIFAdjPtr: 0xA8000 Format: MPLS rdt: on elif: 0xA4013LBL_OP: push dec_ttl: onPV: 0 rwtype: L3_REWRITEsmac_rwt: 1 smac: 000e.39c2.b540 dmac_rwt: 1 dmac: 000e.39c2a123Router#Related Commands
show platform hardware met read
To display platform hardware MET table entries, use the show platform hardware met read command in privileged EXEC mode.
show platform hardware met read {slot slot-num | port port-num {addr addr}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
The show platform hardware met read command displays MET table entry information. For each adjancency use the show platform hardware cef adjacencies entry command to display the MPLS adjacency information.
Examples
This example shows how to display the hardware MET table entries for slot 1 address 18:
Router# show platform hardware met read slot 1 addr 18Starting Offset: 0x0018V E C:3989 I:0x00000 (A: 0x0A8000)Router#Related Commands
show platform hardware statistics
To display platform hardware statistics, use the show platform hardware statistics command.
show platform hardware statistics {drop | exception | module number}
Syntax Description
drop
Displays the dropped statistics.
exception
Displays the statistics that have an exception.
module number
Specifies the module number.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display platform hardware statistics for module 4:
Router# show platform hardware statistics module 4Related Commands
show platform hardware transceiver xml version
To display the hardware abstraction layer (HAL) transceiver XML version information, use the show platform hardware transceiver xml version command.
show platform hardware transceiver xml version
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
This command is useful only if a new transceiver XML version becomes available.
Examples
This example shows how to display the HAL transceiver XML version information:
Router# show platform hardware transceiver xml versionTransceiver image bundle version: INVALIDTransceiver disk version : INVALIDTransceiver runtime using image bundle version: INVALIDregion F1: INVALIDregion F2: INVALID
Note
Related Commands
show platform hardware virtual-map
To display virtual map information, use the show platform hardware virtual-map command.
show platform hardware virtual-map
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display virtual map information:
Router# show platform hardware virtual-mapRelated Commands
show platform hardware xml version
To display the hardware abstraction layer (HAL) XML version information, use the show platform hardware xml version command.
show platform hardware xml version {slot number | file name}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
This command is useful only if a new XML version becomes available.
This command is supported only on modules that have hardware abstraction layer (HAL) support.
Examples
This example shows how to display the HAL XML version information for a module:
Router# show platform hardware xml version slot 4XML image bundle version: 1.1Linecard XML version from region S(Golden): INVALIDXML runtime using image bundle version: 1.1Region F1: INVALID, version: INVALIDRegion F2: INVALID, version: INVALIDRegion S (Golden): version: INVALID
Note
Related Commands
show platform idbhal
To display information about platform interface detector block (IDB) management, use the show platform idbhal command.
show platform idbhal {applications detail | conversion {fib {lif number | ltl-index number | mih number} | lif number | mih number} | interface {gigabitethernet number | null | port-channel number | tengigabitethernet number | tunnel number | vlan vlan_id | detail} | process}
Syntax Description
Command Default
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display information for IDB interface tengigabitethernet 4:
Router# show platform idbhal interface tengigabitethernet 4Related Commands
show platform idbhal conversion
To view platform IDBHAL conversion information, use the show platform idbhal conversion command.
show platform idbhal conversion {fib {lif number | ltl-index number | mih number} | lif number | mih number}
Syntax Description
Defaults
There are no defaults for this command.
Command Modes
Privileged EXEC mode.
Command History
Examples
This example shows how to view platform hardware IDBHAL conversion for LIF 4:
Router# show platform idbhal conversion lif 4Related Commands
show platform ip rsvp
To display RSVP information for the platform IP, use the show platform ip rsvp command.
show platform ip rsvp {interface {async number | auto-template number | ctunnel number | dialer number | esconphy number | filter number | filtergroup number | gigabitethernet number | group-async number | longreachethernet number | loopback number | mfr number | multilink number | null number | port-channel number | portgroup number | pos-channel number | sysclock number | tengigabitethernet number | tunnel number | vif number | virtual-template number | virtual-tokenring number | vlan vlan_id | fcpa number | statistics | voabypassin number | voabypassout number | voafilterin number | voafilterout number | voain number | voaout number}} | netflow identity-string | statistics identity-string}
Syntax Description
Command Default
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the RSVP information for the platform IP with asynchronous interface 4:
Router# show platform ip rsvp interface async 4Related Commands
show platform l2transport gre
To display platform details of Layer 2 over generic routing encapsulation (GRE) tunnel, use the show platform l2transport gre command.
show platform l2transport gre {nodes | summary tunnel _if _number | vlan vlan_id <peerrid> clear-counter}
Syntax Description
Command Default
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display platform details of Layer 2 over GRE tunnel 4:
Router# show platform l2transport gre tunnel 4Related Commands
platform l2transport gre
Configures the platform details of Layer 2 over GRE tunnel.
show platform mrm info
To display platform Match Register Manager (MRM) usage, use the show platform mrm info command.
show platform mrm info
Command Default
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display platform MRM usage:
Router# show platform mrm infoRelated Commands
show platform multicast routing
To display multicast configuration in routing mode, use the show platform multicast routing command.
show platform multicast routing {replication}
Syntax Description
Command Default
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display LTL-sharing across VLANs in multicast routing configuration:
Router# show platform multicast routing replicationRelated Commands
platform multicast routing
Configures the multicast routing information for the platform.
show platform nvhmr
To display platform Non-Volatile Health Monitor Record (NVHMR), use the show platform nvhmr command.
show platform nvhmr {current {all | entry number | summary} | previous{all | entry number | summary}}
Syntax Description
Command Default
None
Command Modes
Privileged EXEC mode.
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display platform NVHMR of current entry number 4:
Router# show platform nvhmr current entry 4Related Commands
show platform qos aggregate policer
To display information about the aggregate policer for platform quality of service (QoS), use the show platform qos aggregate policer command in EXEC mode.
show platform qos aggregate policer [aggregate-name]
Syntax Description
Command Default
None
Command Modes
EXEC
Command History
Usage Guidelines
Aggregate policing works independently on each Distributed Forwarding Card (DFC)-equipped switching module and independently on the Policy Feature Card 2 (PFC2), which supports any non-DFC-equipped switching modules. Aggregate policing does not combine flow statistics from different DFC-equipped switching modules. You can display aggregate-policing statistics for each DFC-equipped switching module, the PFC2, and any non-DFC-equipped switching modules that are supported by the PFC2.
Examples
This example shows how to display information about the aggregate policer for platform QoS:
Router# show platform qos aggregate-policerag1 (undefined)AgId=0 [ pol1 pol2 ]ag2 64000 64000 conform-action set-dscp-transmit 56 exceed-action dropAgId=0 [ pol3 ]ag3 32000 32000 conform-action set-dscp-transmit 34 exceed-action dropIn the output, the following applies:
•
•
•
•
Related Commands
platform qos aggregate-policer
Defines a named aggregate policer for use in policy maps.
show platform qos maps
To display platform quality of service (QoS) mapping information, use the show platform qos maps command in privileged EXEC mode.
Cisco 2600, 3660, 3700, 3845, 7200, 7400, and 7500 Series Routers
show platform qos maps [cos-dscp | dscp-cos]
Cisco 7600 Series Router and Catalyst 6500 Series Switch
show platform qos maps [cos-dscp | cos-mutation | dscp-cos | dscp-exp | dscp-mutation | exp-dscp | exp-mutation | ip-prec-dscp | policed-dscp]
Syntax Description
Command Default
All platform QoS maps are displayed.
Command Modes
Privileged EXEC (#)
Command History
Usage Guidelines
Maps are used to generate an internal DSCP value, which represents the priority of the traffic. Use the show platform qos maps command without keywords to display all maps.
Examples
The following is sample output from the show platform qos maps cos-dscp command displaying the DSCP values to which each CoS value will be mapped:
Router# show platform qos maps cos-dscpCos-dscp map:cos: 0 1 2 3 4 5 6 7--------------------------------dscp: 8 8 8 8 24 32 56 56The following is sample output from the show platform qos maps dscp-cos command displaying the CoS values to which each DSCP value will be mapped:
Router# show platform qos maps dscp-cosDscp-cos map:dscp: 0 8 10 16 18 24 26 32 34 40 46 48 56-----------------------------------------------cos: 0 1 1 1 2 2 3 3 4 4 5 6 7This example shows how to display the QoS-map settings:
Router# show platform qos mapsPoliced-dscp map:0 1 2 3 4 5 6 7 8 9----------------------------------00: 00 01 02 03 04 05 06 07 08 0910: 10 11 12 13 14 15 16 17 18 1920: 20 21 22 23 24 25 26 27 28 2930: 30 31 32 33 34 35 36 37 38 3940: 40 41 42 43 44 45 46 47 48 4950: 50 51 52 53 54 55 56 57 58 5960: 60 61 62 63Dscp-cos map:0 1 2 3 4 5 6 7 8 9----------------------------------00: 00 00 00 00 00 00 00 00 01 0110: 01 01 01 01 01 01 02 02 02 0220: 02 02 02 02 03 03 03 03 03 0330: 03 03 04 04 04 04 04 04 04 0440: 05 05 05 05 05 05 05 05 06 0650: 06 06 06 06 06 06 07 07 07 0760: 07 07 07 07Cos-dscp map:cos: 0 1 2 3 4 5 6 7----------------------------------dscp: 0 8 16 24 32 40 48 56IpPrecedence-dscp map:ipprec: 0 1 2 3 4 5 6 7----------------------------------dscp: 0 8 16 24 32 40 48 56Router#In the policed DSCP and DSCP-CoS map displays, the new DSCP or CoS values are shown in the body of the table. The decade of the original DSCP value is shown in the left-side vertical column, and the units digit is in the top row. For example, the DSCP-CoS map indicates that if the original DSCP value is between 32 and 39, the CoS will be set to 4.
The CoS-DSCP and IP precedence-DSCP maps display the DSCP values to which each CoS or IP precedence value will be mapped. For example, the IP precedence-DSCP map indicates that if the original IP precedence value is 3, the DSCP will be set to 24.
This example shows how to verify the configuration of DSCP-mutation mapping:
Router# show platform qos maps | begin DSCP mutationDSCP mutation map mutmap1: (dscp= d1d2)d1 : d2 0 1 2 3 4 5 6 7 8 9-------------------------------------0 : 00 01 02 03 04 05 06 07 08 091 : 10 11 12 13 14 15 16 17 18 192 : 20 21 22 23 24 25 26 27 28 293 : 08 31 32 33 34 35 36 37 38 394 : 40 41 42 43 44 45 46 47 48 49<...Output Truncated...>Router#In the DSCP mutation map display, the marked-down DSCP values are shown in the body of the table. The first digit (d1) of the original DSCP value is in the left-side vertical column labeled d1, and the second digit (d2) is in the top row. For example, a DSCP value of 30 maps to a new DSCP value of 08.
Related Commands
show platform redundancy
To display platform-specific Constellation WAN (CWAN) redundancy information, use the show platform redundancy command in privileged EXEC mode.
show platform redundancy {atm | bias | ccb slot-number cpu-number | cwpa-ce3 | cwpa-ct3 | cwpa-e1 | cwpa-stm1 | cwpa-t1 | frame-relay | hdlc | if-config {slot-number cpu-number [bay-number] | default-retvals} | mlp | multilink-vc | osm-chocx | osm-ct3 | ppp | shadowstate | spa-chocx | spa-ct3 | switchover}
Syntax Description
Command Default
None
Command Modes
Privileged EXEC (#)
Command History
Examples
The following is sample output from the show platform redundancy command with the if-config keyword. The fields are self-explanatory.
Router# show platform redundancy if-config 4 0Current number of elements = 0Current maximum elements = 128List was grown = 0 timesNumber of elements sorted = 0List errors = 0List flags = 0x1ECurrent element pointer = 0x0List pointer = 0x50A27438+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+| C=Command T=Type P=Port t=timedOut D=Dirty S=Sync |+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+| C | T | P | key address | t | D | S | value |+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--++--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+Related Commands
show platform software acl
To display platform software ACL, use the show platform software acl command.
show platform software acl {accounting-tbl {index number} | acct-xlt-tbl {in {index number} | out {index number}} | appid {in number | out number} | capmap {tcam {A {index | module} | B {index | module}}} | cm-readiness {module} | compaction {detail {module} | label {tcam {A | B}} | module number} | entry {module} | label {tcam{A | B}} | lou {index number | module number} | tcam {count {module}} | tcp-flags-tbl {detail {module} | index number | module number} | v6-extnhdr-tbl {detail | index | module}}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Examples
This example shows how to display platform software ACL application ID Acct-Xlt in entry 4:
Router# show platform software acl appid in 4Related Commands
show platform software debug
To display platform software debug logging details, use the show platform software debug command.
show platform software debug
Syntax Description
This command has no arguments or keywords.
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the platform software debug logging details:
Router# show platform software debugRelated Commands
show platform software e8-recovery
To display platform software EARL8 print recovery patch settings and occurrences, use the show platform software e8-recovery command.
show platform software e8-recovery {config | counter | data | history}
Syntax Description
Defaults
None
Command Modes
Privileged EXEC mode
Command History
Usage Guidelines
There are no usage guidelines for this command.
Examples
This example shows how to display the platform EARL8 software print recovery patch settings:
Router# show platform software e8-recovery configRelated Commands
platform software e8-recovery
Configures the platform EARL8 software print recovery patch settings and occurrences.
