Table Of Contents

M Commands

member (fcalias configuration mode)

member (zone configuration mode)

member (zoneset configuration mode)

M Commands

---

This chapter describes the Cisco NX-OS Fibre Channel, virtual Fibre Channel, and Fibre Channel over Ethernet (FCoE) commands that begin with M.

member (fcalias configuration mode)

To add a member name to a Fibre Channel alias on a Virtual SAN (VSAN), use the member command. To remove a member name from a Fibre Channel alias, use the no form of this command.

member {device-alias aliasname | domain-id domain-id port-number port-number | fcid fc-id | fwwn fwwn-id | interface fc slot/port [domain-id domain-id | swwn swwn-id] | pwwn pwwn-id | symbolic-nodename nodename}

no member {device-alias aliasname | domain-id domain-id port-number port-number | fcid fc-id | fwwn fwwn-id | interface fc slot/port [domain-id domain-id | swwn swwn-id] | pwwn pwwn-id | symbolic-nodename nodename}

Syntax Description

device-alias aliasname	Specifies the member device alias. The name can be a maximum of 64 characters.
domain-id domain-id	Specifies the member domain ID. The range is from 1 to 239.
port-number port-number	Specifies a port number in the range of 0 to 255.
fcid fc-id	Specifies the member FC ID. The format is 0xhhhhhh, where h is a hexadecimal digit.
fwwn fwwn-id	Specifies the member fWWN ID. The format is hh:hh:hh:hh:hh:hh:hh:hh, where h is a hexadecimal digit.
interface fc slot/port	Specifies the member interface ID and its slot number and port number.
swwn swwn-id	(Optional) Specifies the member sWWN ID. The format is hh:hh:hh:hh:hh:hh:hh:hh, where h is a hexadecimal digit.
pwwn pwwn-id	Specifies the member pWWN ID. The format is hh:hh:hh:hh:hh:hh:hh:hh, where h is a hexadecimal digit.
symbolic-nodename nodename	Specifies the member symbolic node name. The maximum length is 255 characters.

Command Default

None

Command Modes

Fcalias configuration mode

Command History

Release	Modification
6.0(2)N1(1)	This command was introduced.

Examples

This example shows how to add a member to an alias called samplealias:

switch(config)# fcalias name samplealias

This example shows how to define a Fibre Channel interface for the member:

switch(config-fcalias)# member interface fc3/1

This example shows how to delete the specified member:

switch(config-fcalias)# no member interface fc3/1

Related Commands

Command	Description
fcalias name	Configures an alias.
show fcalias	Displays the member name information in an alias.

member (zone configuration mode)

To add a member name to a Fibre Channel zone, use the member command. To remove a member name from a zone, use the no form of this command.

member {device-alias aliasname | domain-id domain-id port-number port | fcalias alias-name | fcid fc-id | fwwn fwwn-id | interface fc slot/port [domain-id domain-id | swwn swwn-id] | pwwn pwwn-id [lun lun-id] | symbolic-nodename nodename}

no member {device-alias aliasname | domain-id domain-id port-number port | fcalias alias-name | fcid fc-id | fwwn fwwn-id | interface fc slot/port [domain-id domain-id | swwn swwn-id] | pwwn pwwn-id [lun lun-id] | symbolic-nodename nodename}

Syntax Description

device-alias aliasname	Specifies the member device alias. The name can be a maximum of 64 characters.
domain-id domain-id	Specifies the member domain ID. The range is from 1 to 239.
port-number port	Specifies the member port number. The range is from is 0 to 255.
fcalias alias-name	Specifies a Fibre Channel alias name. The name can be a maximum of 64 characters.
fcid fc-id	Specifies the member FC ID. The format is 0xhhhhhh, where h is a hexadecimal digit.
fwwn fwwn-id	Specifies the member fWWN ID. The format is hh:hh:hh:hh:hh:hh:hh:hh, where h is a hexadecimal digit.
interface fc slot/port	Specifies the member interface ID and its slot number and port number.
swwn swwn-id	(Optional) Specifies the member sWWN ID. The format is hh:hh:hh:hh:hh:hh:hh:hh, where h is a hexadecimal digit.
pwwn pwwn-id	Specifies the member pWWN ID. The format is hh:hh:hh:hh:hh:hh:hh:hh, where h is a hexadecimal digit.
lun lun-id	(Optional) Specifies the member Logical Unit Number (LUN) ID. The format is 0xhhhh[:hhhh[:hhhh[:hhhh]]], where h is a hexadecimal digit.
symbolic-nodename nodename	Specifies the member symbolic node name. The name can be a maximum of 255 characters.

Command Default

None

Command Modes

Zone set zone configuration mode and zoneset-zone configuration mode

Command History

Release	Modification
6.0(2)N1(1)	This command was introduced.

Usage Guidelines

Create a zone set zone member only if you need to add member to a zone from the zone set prompt.

Examples

This example shows how to add a member to a zone called zs1 on VSAN 1:

switch(config)# zone name zs1 vsan 1 

switch(config-zone)# member fcid 0x111112 

This example shows how to add a zone to a zone set called Zoneset1 on VSAN 1:

switch(config)# zoneset name ZoneSet1 vsan 1 

switch(config-zoneset-zone)# member fcid 0x111112 

This example shows how to assign a Fibre Channel interface member into a zone:

switch(config)# zoneset name ZoneSet1 vsan 1 

switch(config-zoneset-zone)# member interface fc 3/1 

This example shows how to delete the specified device from a zone:

switch(config-zoneset-zone)# no member interface fc 3/1 

Related Commands

Command	Description
zoneset (configuration mode)	Specifies a name for a zone set.
zone name (zone set configuration mode)	Configures a zone in a zone set.
show zoneset	Displays zone set information.

member (zoneset configuration mode)

To configure zone set members, use the member command. To remove a zone set member, use the no form of this command.

member member-name

no member member-name

Syntax Description

member-name

Member name. The name can be a maximum of 64 characters.

Command Default

None

Command Modes

Zone set configuration mode

Command History

Release	Modification
6.0(2)N1(1)	This command was introduced.

Examples

This example shows how to add a member zone to a zone set:

switch(config)# zoneset name Zoneset1 vsan 10 

switch(config-zoneset)# member ZoneA 

Related Commands

Command	Description
show zone	Displays zone information.
zoneset name	Creates a zone set.