Table Of Contents

Show Commands

show forwarding distribution ip igmp snooping

show forwarding distribution multicast

show forwarding distribution multicast client

show forwarding distribution multicast outgoing-interface-list

show forwarding distribution multicast route

show forwarding multicast outgoing-interface-list

show forwarding multicast route

show ip igmp event-history

show ip igmp groups

show ip igmp interface

show ip igmp local-groups

show ip igmp route

show ip igmp snooping

show ip igmp snooping event-history

show ip igmp snooping explicit-tracking

show ip igmp snooping groups

show ip igmp snooping mrouter

show ip igmp snooping querier

show ip igmp snooping statistics

show ip mroute

show ip mroute summary

show ip msdp count

show ip msdp event-history

show ip msdp mesh-group

show ip msdp peer

show ip msdp policy statistics sa-policy

show ip msdp route

show ip msdp rpf

show ip msdp sa-cache

show ip msdp route

show ip msdp sources

show ip msdp summary

show ip pim event-history

show ip pim group-range

show ip pim interface

show ip pim neighbor

show ip pim oif-list

show ip pim policy statistics auto-rp

show ip pim policy statistics bsr

show ip pim policy statistics jp-policy

show ip pim policy statistics neighbor-policy

show ip pim policy statistics register-policy

show ip pim route

show ip pim rp

show ip pim rp-hash

show ip pim statistics

show ip pim vrf

show ip static-route

show routing ip multicast event-history

show routing multicast

show routing multicast clients

show running-config igmp

show running-config msdp

show running-config pim

show startup-config igmp

show startup-config msdp

show startup-config pim

Show Commands

---

This chapter describes the Cisco NX-OS multicast routing show commands.

show forwarding distribution ip igmp snooping

To display information about Layer 2 IGMP snooping multicast Forwarding Information Base (FIB) distribution, use the show forwarding distribution ip igmp snooping command.

show forwarding distribution ip igmp snooping [vlan vlan-id [group group-addr [source source-addr]]]

Syntax Description

vlan vlan-id	(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.
group group-addr	(Optional) Specifies a group address.
source source-addr	(Optional) Specifies a source address.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about Layer 2 IGMP snooping multicast FIB distribution:

switch(config)# show forwarding distribution ip igmp snooping

Related Commands

Command	Description
test forwarding distribution perf	Tests the forwarding distribution performance of the Forwarding Information Base (FIB).

show forwarding distribution multicast

To display information about multicast Forwarding Information Base (FIB) distribution messages, use the show forwarding distribution multicast command.

show forwarding distribution multicast [messages]

Syntax Description

messages

(Optional) Displays message information.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about multicast distribution messages:

switch(config)# show forwarding distribution multicast

Number of Multicast FIB Processes Active: 1

Slot     FIB State

   1        ACTIVE

switch#

show forwarding distribution multicast client

To display information about the multicast Forwarding Information Base (FIB) distribution client, use the show forwarding distribution multicast client command.

show forwarding distribution multicast client

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast FIB distribution client:

switch# show forwarding distribution multicast client

Client-name  Client-id  Shared Memory Name

mrib         1          mrib-mfdm

switch# 

show forwarding distribution multicast outgoing-interface-list

To display information about the multicast Forwarding Information Base (FIB) outgoing interface (OIF) list, use the show forwarding distribution multicast outgoing-interface-list command.

show forwarding distribution multicast outgoing-interface-list {L2 | L3} [index]

Syntax Description

L2	Specifies the Layer 2 OIF list.
L3	Specifies the Layer 3 OIF list.
index	(Optional) OIF list index.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast OIF list for Layer 3:

switch# show forwarding distribution multicast outgoing-interface-list L3

show forwarding distribution multicast route

To display information about the multicast Forwarding Information Base (FIB) distribution routes, use the show forwarding distribution multicast route command.

show forwarding distribution [ip | ipv4] multicast route [table id | vrf vrf_name] [[group {group-addr [mask] | group-prefix}] [source {source-addr [source-mask] | source-prefix}] | summary]

Syntax Description

ip	(Optional) Specifies IPV4 information.
ipv4	(Optional) Specifies IPV4 information.
table id	(Optional) Specifies the multicast routing table ID. The range is from 0 to 2147483647.
vrf vrf_name	(Optional) Specifies a virtual routing and forwarding (VRF) name. The name can be a maximum of 32 alphanumeric characters.
group	(Optional) Specifies an IPv4 multicast group.
group-addr	IPv4 multicast group address.
mask	(Optional) Mask for the group address.
group-prefix	(Optional) IPv4 multicast group prefix.
source	(Optional) Specifies an IPv4 multicast source.
source-addr	IPv4 source address.
source-mask	(Optional) Mask for the group address.
source-prefix	(Optional) IPv4 multicast source prefix.
summary	(Optional) Displays the route counts.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about all the multicast FIB distribution routes:

switch(config)# show forwarding distribution multicast route

IPv4 Multicast Routing Table for table-id: 1

Total number of groups: 5

Legend:

   C = Control Route

   D = Drop Route

   G = Local Group (directly connected receivers)

   O = Drop on RPF Fail

   P = Punt to supervisor

   d = Decap Route

  (*, 224.0.0.0/4), RPF Interface: NULL, flags: D

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 224.0.0.0/24), RPF Interface: NULL, flags: CP

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 224.0.1.39/32), RPF Interface: NULL, flags: CP

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 224.0.1.40/32), RPF Interface: NULL, flags: CP

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

  (*, 232.0.0.0/8), RPF Interface: NULL, flags: D

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 0

    Null Outgoing Interface List

switch#

show forwarding multicast outgoing-interface-list

To display information about the multicast Forwarding Information Base (FIB) outgoing interface (OIF) list, use the show forwarding multicast outgoing-interface-list command.

show forwarding multicast outgoing-interface-list [index]

Syntax Description

index

(Optional) OIF list index. The OIF list index is from 1 to 65535.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the multicast FIB OIF list:

switch# show forwarding multicast outgoing-interface-list

  Outgoing Interface List Index: 1

  Reference Count: 1

    Ethernet1/5

switch#

Related Commands

Command	Description
ip igmp static-oif	Binds a multicast group to the outgoing interface (OIF).
clear ip igmp interface statistics	Clears the IGMP statistics for an interface.

show forwarding multicast route

To display information about the IPv4 Forwarding Information Base (FIB) multicast routes, use the show forwarding multicast route command.

show forwarding [vrf {vrf-name | all}] [ip | ipv4] multicast route {[group {group-addr [group-mask] | group-prefix} | source {source-addr [source-mask] | source-prefix} | module num | vrf {vrf-name | all}] | summary [vrf {vrf-name | all}]}

Syntax Description

vrf	(Optional) Displays information for a specified virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Displays information for all VRFs.
ip	(Optional) Specifies IPv4.
ipv4	(Optional) Specifies IPv4.
group	(Optional) Specifies an IPv4 multicast group address.
group-addr	IPv4 multicast group address.
group-mask	(Optional) IPv4 multicast group address mask.
group-prefix	(Optional) IPv4 multicast group prefix.
source	(Optional) Specifies an IPv4 multicast source address.
source-addr	IPv4 multicast source address.
source-mask	IPv4 multicast source address mask.
source-prefix	IPv4 multicast source prefix.
summary	Displays route counts.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the IPv4 multicast FIB routes:

switch# show forwarding multicast route 

IPv4 Multicast Routing table table-id:1

Total number of groups: 1

Legend:

   C = Control Route

   D = Drop Route

   G = Local Group (directly connected receivers)

   O = Drop on RPF failure

   P = Punt to Supervisor

   W = Wildcard

   d = OTV Decap route

  (*, 230.0.0.0/32), RPF Interface: NULL, flags: DG

    Received Packets: 0 Bytes: 0

    Number of Outgoing Interfaces: 1

    Outgoing Interface List Index: 1

      Ethernet1/5 Outgoing Packets:0 Bytes:0

switch# 

This example shows how to display the summary information about the IPv4 multicast FIB routes:

switch# show forwarding multicast route summary 

IPv4 Multicast Routing Table for Context "default"

Total number of routes: 1

Total number of (*,G) routes: 1

Total number of (S,G) routes: 0

Total number of (*,G-prefix) routes: 0

Group count: 1

Prefix insert fail count: 9

switch#

Related Commands

Command	Description
clear ip mroute	Clears the multicast routing table.

show ip igmp event-history

To display information in the IGMP event history buffers, use the show ip igmp event-history command.

show ip igmp event-history {clis | debugs | errors | events | ha | igmp-internal | msgs | mtrace | policy | statistics | vrf}

Syntax Description

clis	Displays events of type CLI.
debugs	Displays events of type debug.
errors	Displays events of type error.
events	Displays events of type event.
ha	Displays events of type HA.
igmp-internal	Displays events of type IGMP internal.
msgs	Displays events of type msg.
mtrace	Displays events of type mtrace.
policy	Displays events of type policy.
statistics	Displays events of type statistics.
vrf	Displays events of type VRF.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the IGMP HA event history buffer:

switch(config)# show ip igmp event-history ha

 ha events for IGMP process

2008 Apr 12 04:01:32.339950 igmp [4588]: : Router-port PSS entry for vlan 20 upd

ated [count 0]

2008 Apr 12 04:00:05.118545 igmp [4588]: : Handling existing vlans notification

2008 Apr 12 04:00:04.824730 igmp [4588]: : PSS entry for global updatedswitch(config)#

Related Commands

Command	Description
clear ip igmp event-history	Clears the contents of the IGMP event history buffers.
ip igmp event-history	Configures the size of IGMP event history buffers.

show ip igmp groups

To display information about IGMP-attached group membership, use the show ip igmp groups command.

show ip igmp groups [{source [group]} | {group [source]}] [ethernet slot/port | port-channel channel-number[.sub_if_number] | vlan vlan-id] [vrf {vrf-name | all}]

Syntax Description

source	Source IP address.
group	(Optional) Multicast IP address of the single group to display.
ethernet slot/port	(Optional) Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	(Optional) Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if_number	(Optional) Subinterface number. The range is from 1 to 4093.
vlan vlan-id	(Optional) Specifies the VLAN. The range is from 1 to 4094.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip igmp route command is an alternative form of this command.

This command does not require a license.

Examples

This example shows how to display information about the IGMP-attached group membership:

switch(config)# show ip igmp groups

IGMP Connected Group Membership for VRF "default" - 0 total entries

Type: S - Static, D - Dynamic, L - Local, T - SSM Translated

Group Address      Type Interface           Uptime    Expires   Last Reporter

switch(config)# 

Related Commands

Command	Description
show ip igmp route	Displays information about the IGMP-attached group membership.

show ip igmp interface

To display information about IGMP on interfaces, use the show ip igmp interface command.

show ip igmp interface {ethernet slot/port | port-channel channel-number[.sub_if_number] | vlan vlan-id}

show ip igmp interface [brief] [vrf {vrf-name | all}]

Syntax Description

ethernet slot/port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if_number	Subinterface number. The range is from 1 to 4093.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.
brief	(Optional) Displays one line status per interface.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP on an interface (if IGMP is not in vPC mode, the vPC information is not displayed):

switch(config)# show ip igmp interface vlan 5

IGMP Interfaces for VRF "default"

Vlan20, Interface status: protocol-down/link-down/admin-down

  IP address: 20.1.1.3, IP subnet: 20.1.1.0/24

  Active querier: 0.0.0.0

  Membership count: 0

  Old Membership count 0

  Route-queue depth: 0

  IGMP version: 2, host version: 0

  IGMP query interval: 125 secs, configured value: 125 secs

  IGMP max response time: 10 secs, configured value: 10 secs

  IGMP startup query interval: 31 secs, configured value: 31 secs

  IGMP startup query count: 2

  IGMP last member mrt: 1 secs

  IGMP last member query count: 2

  IGMP group timeout: 260 secs, configured value: 260 secs

  IGMP querier timeout: 255 secs, configured value: 255 secs

  IGMP unsolicited report interval: 10 secs

  IGMP robustness variable: 2, configured value: 2

  IGMP reporting for link-local groups: disabled

  IGMP interface enable refcount: 1

  IGMP interface immediate leave: disabled

  IGMP Report Policy: None

  IGMP State Limit: None

  IGMP interface statistics:

    General (sent/received):

      v1-reports: 0/0

      v2-queries: 0/0, v2-reports: 0/0, v2-leaves: 0/0

      v3-queries: 0/0, v3-reports: 0/0

    Errors:

      General Queries received with invalid destination address; v2: 0, v3: 0

      Checksum errors: 0, Packet length errors: 0

      Packets with Local IP as source: 0, Source subnet check failures: 0

      Query from non-querier:0

      Report version mismatch: 0, Query version mismatch: 0

      Unknown IGMP message type: 0

      Invalid v1 reports: 0, Invalid v2 reports: 0, Invalid v3 reports: 0

    Packets dropped due to router-alert check: 0

  Interface PIM DR: No

  Interface vPC CFS statistics:

    DR queries sent: 0

    DR queries rcvd: 0

    DR queries fail: 0

    DR updates sent: 0

    DR updates rcvd: 0

    DR updates fail: 0

switch(config)#

This example shows how to display information about IGMP on an interface in a brief format:

switch(config)# show ip igmp interface brief

IGMP Interfaces for VRF "default", count: 1

Interface            IP Address      IGMP Querier    Membership  Version

                                                     Count

Vlan20               20.1.1.3        0.0.0.0         0           v2

switch(config)#

show ip igmp local-groups

To display information about IGMP local groups, use the show ip igmp local-groups command.

show ip igmp local-groups [ethernet slot/port | port-channel channel-number[.sub_if_number] | vlan vlan-id] [vrf {vrf-name | all}]

Syntax Description

ethernet slot/port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if_number	Subinterface number. The range is from 1 to 4093.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP local groups:

switch(config)# show ip igmp local-groups

show ip igmp route

To display information about the IGMP-attached group membership, use the show ip igmp route command.

show ip igmp route [{source [group]} | {group [source]}] [ethernet slot/port | port-channel channel-number[.sub_if_number] | vlan vlan-id] [vrf {vrf-name | all}]

Syntax Description

source	Source IP address.
group	(Optional) Multicast IP address of single group to display.
ethernet slot/port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if_number	Subinterface number. The range is from 1 to 4093.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip igmp groups command is an alternative form of this command.

This command does not require a license.

Examples

This example shows how to display information about the IGMP-attached group membership:

switch# show ip igmp route

IGMP Connected Group Membership for VRF "default" - 1 total entries

Type: S - Static, D - Dynamic, L - Local, T - SSM Translated

Group Address      Type Interface           Uptime    Expires   Last Reporter

230.0.0.0          S    Ethernet1/5         00:31:47  never     0.0.0.0

switch#

Related Commands

Command	Description
show ip igmp groups	Displays information about the IGMP-attached group membership.

show ip igmp snooping

To display information about IGMP snooping, use the show ip igmp snooping command.

show ip igmp snooping [vlan vlan-id]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093. The default is all VLANs.

Command Default

Displays all VLANs.

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP snooping for a VLAN:

switch(config)# show ip igmp snooping vlan 20

IGMP Snooping information for vlan 20

  IGMP snooping enabled

  Optimised Multicast Flood (OMF) disabled

  IGMP querier none

  Switch-querier disabled

  IGMPv3 Explicit tracking enabled

  IGMPv2 Fast leave disabled

  IGMPv1/v2 Report suppression enabled

  IGMPv3 Report suppression disabled

  Link Local Groups suppression enabled

  Router port detection using PIM Hellos, IGMP Queries

  Number of router-ports: 1

  Number of groups: 0

  Active ports:

    Eth1/21     Po100

switch(config)#

show ip igmp snooping event-history

To display information in the IGMP snooping event history buffers, use the show ip igmp snooping event-history command.

show ip igmp snooping event-history {vpc | igmp-snoop-internal | mfdm | mfdm-sum | vlan | vlan-events}

Syntax Description

vpc	Displays the event history buffer of type virtual port channel (vPC).
igmp-snoop- internal	Displays the event history buffer of type IGMP snooping internal.
mfdm	Displays the event history buffer of type multicast FIB distribution (MFDM).
mfdm-sum	Displays the event history buffer of type MFDM sum.
vlan	Displays the event history buffer of type VLAN.
vlan-events	Displays the event history buffer of type VLAN events.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information in the IGMP snooping VLAN event history buffer:

switch(config)# show ip igmp snooping event-history vlan

 vlan Events for IGMP snoopprocess

2008 Apr 12 06:30:47.790031 igmp [4588]: : IGMPv3 proxy report: no routers found

2008 Apr 12 06:30:47.790012 igmp [4588]: : IGMPv3 proxy report: no records to se

nd

2008 Apr 12 06:30:47.789882 igmp [4588]: : IGMPv3 proxy report: no routers found

2008 Apr 12 06:30:47.789740 igmp [4588]: : IGMPv3 proxy report: no routers found

2008 Apr 12 06:30:47.789721 igmp [4588]: : IGMPv3 proxy report: no records to se

nd

2008 Apr 12 06:30:47.789584 igmp [4588]: : IGMPv3 proxy report: no routers found

2008 Apr 12 06:13:17.022028 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:17.022023 igmp [4588]: : Received a STP Topology change notifi

cation

2008 Apr 12 06:13:15.022294 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:15.022289 igmp [4588]: : Received a STP Topology change notifi

cation

2008 Apr 12 06:13:14.662417 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:14.662412 igmp [4588]: : Received a STP Topology change notifi

cation

2008 Apr 12 06:13:12.642393 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:12.642388 igmp [4588]: : Received a STP Topology change notifi

cation

2008 Apr 12 06:13:11.946051 igmp [4588]: : Received a STP Topology change notifi

cation, 1 vlans

2008 Apr 12 06:13:11.946046 igmp [4588]: : Received a STP Topology change notifi

cation

<--Output truncated-->

switch(config)#

Related Commands

Command	Description
ip igmp snooping event-history	Configures the size of the IGMP snooping event history buffers.
clear ip igmp snooping event-history	Clears information in the IGMP snooping event history buffers.

show ip igmp snooping explicit-tracking

To display information about explicit tracking for IGMP snooping, use the show ip igmp snooping explicit-tracking command.

show ip igmp snooping explicit-tracking [vlan vlan-id]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

When you use this command without the optional vlan argument, the system displays information for all VLANs.

This command does not require a license.

Examples

This example shows how to display information about explicit tracking for IGMP snooping for VLAN 33:

switch# show ip igmp snooping explicit-tracking vlan 33

Related Commands

Command	Description
clear ip igmp snooping explicit-tracking vlan	Clears the IGMP snooping explicit host tracking information for VLANs.
ip igmp snooping explicit-tracking	Enables tracking of IGMPv3 membership reports from individual hosts for each port on a VLAN.

show ip igmp snooping groups

To display information about the group membership for IGMP snooping, use the show ip igmp snooping groups command.

show ip igmp snooping groups [{source [group]} | {group [source]}] [vlan vlan-id] [detail]

Syntax Description

source	(Optional) Source address for route.
group	(Optional) Group address for route.
vlan vlan-id	(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.
detail	(Optional) Displays detailed information for the group.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about the group membership for IGMP snooping:

switch(config)# show ip igmp snooping groups

TType: S - Static, D - Dynamic, R - Router port

Vlan  Group Address      Ver  Type  Port list

20    */*                -    R     Vlan20

switch(config)#

show ip igmp snooping mrouter

To display the multicast routers detected by IGMP snooping, use the show ip igmp snooping mrouter command.

show ip igmp snooping mrouter [vlan vlan-id]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display the multicast routers detected by IGMP snooping:

switch(config)# show ip igmp snooping mrouter

Type: S - Static, D - Dynamic, V - vPC Peer Link

Type: S - Static, D - Dynamic, V - vPC Peer Link, I - Internal

Vlan  Router-port   Type      Uptime      Expires

20    Vlan20        I         04:16:16    never (down)

switch(config)#

show ip igmp snooping querier

To display information about IGMP snooping queriers, use the show ip igmp snooping querier command.

show ip igmp snooping querier [vlan vlan-id]

Syntax Description

vlan vlan-id

(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command does not require a license.

Examples

This example shows how to display information about IGMP snooping queriers:

switch(config)# show ip igmp snooping querier

show ip igmp snooping statistics

To display information about IGMP snooping statistics, use the show ip igmp snooping statistics command.

show ip igmp snooping statistics [vlan vlan-id | global]

Syntax Description

vlan vlan-id	(Optional) Specifies a VLAN. The range is from 1 to 3967 and 4048 to 4093.
global	(Optional) Specifies the global statistics.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

When you use this command without any options, the system prints statistics for all VLANs.

This command does not require a license.

Examples

This example shows how to display information about IGMP snooping statistics for VLAN 1:

switch(config)# show ip igmp snooping statistics vlan 1

show ip mroute

To display information about IPv4 multicast routes, use the show ip mroute command.

show ip mroute {group | {source group} | {group [source]}} [summary [software-forwarded]] [vrf {vrf-name | all}]

Syntax Description

group	Group address for route.
source	Source address for route.
summary	(Optional) Displays route counts and packet rates.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 multicast routes:

switch(config)# show ip mroute

IP Multicast Routing Table for VRF "default"

(*, 232.0.0.0/8), uptime: 04:18:55, pim ip

  Incoming interface: Null, RPF nbr: 0.0.0.0

  Outgoing interface list: (count: 0)

switch(config)#

Related Commands

Command	Description
show ip mroute summary	Displays summary information about IPv4 multicast routes.

show ip mroute summary

To display summary information about IPv4 multicast routes, use the show ip mroute summary command.

show ip mroute summary [count | software-forwarded] [vrf {vrf-name | all}]

show ip mroute [group] summary [software-forwarded] [vrf {vrf-name | all}]

Syntax Description

count	(Optional) Displays only route counts.
software- forwarded	(Optional) Displays software-switched route counts only.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
group	(Optional) Specifies a group address for a route.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display summary information about IPv4 multicast routes:

switch(config)# show ip mroute summary

IP Multicast Routing Table for VRF "default"

Total number of routes: 1

Total number of (*,G) routes: 0

Total number of (S,G) routes: 0

Total number of (*,G-prefix) routes: 1

Group count: 0, rough average sources per group: 0.0

Group: 232.0.0.0/8, Source count: 0

Source          packets      bytes           aps   pps       bit-rate     oifs

(*,G)           0            0               0     0         0.000   bps  0

switch(config)#

This example shows how to display the number of IPv4 multicast routes:

switch# show ip mroute summary count

IP Multicast Routing Table for VRF "default"

Total number of routes: 2

Total number of (*,G) routes: 1

Total number of (S,G) routes: 0

Total number of (*,G-prefix) routes: 1

Group count: 1, rough average sources per group: 0.0

switch# 

Related Commands

Command	Description
show ip mroute	Displays information about IPv4 multicast routes.

show ip msdp count

To display information about Multicast Source Discovery Protocol (MSDP) counts, use the show ip msdp count command.

show ip msdp count [asn] [vrf {vrf-name | all}]

Syntax Description

asn	(Optional) Autonomous system (AS) number.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display MSDP counts:

switch(config)# show ip msdp count

show ip msdp event-history

To display information in the Multicast Source Discovery Protocol (MSDP) event history buffers, use the show ip msdp event-history command.

show ip msdp event-history {errors | msgs | statistics}

Syntax Description

errors	Displays events of type error.
msgs	Displays events of type msg.
statistics	Displays events of type statistics.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Examples

This example shows how to display information in the MSDP msgs event history buffer:

switch(config)# show ip msdp event-history msgs

Related Commands

Command	Description
clear ip msdp event-history	Clears the contents of the MSDP event history buffers.
ip msdp event-history	Configures the size of MSDP event history buffers.

show ip msdp mesh-group

To display information about Multicast Source Discovery Protocol (MSDP) mesh groups, use the show ip msdp mesh-group command.

show ip msdp mesh-group [mesh-group] [vrf {vrf-name | all}]

Syntax Description

mesh-group	(Optional) Mesh group name.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP mesh groups:

switch(config)# show ip msdp mesh-group

show ip msdp peer

To display information about Multicast Source Discovery Protocol (MSDP) peers, use the show ip msdp peer command.

show ip msdp peer [peer-address] [vrf {vrf-name | all}]

Syntax Description

peer-address	(Optional) IP address of an MSDP peer.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP peers:

switch(config)# show ip msdp peer

show ip msdp policy statistics sa-policy

To display information about Multicast Source Discovery Protocol (MSDP) Source-Active (SA) policies, use the show ip msdp policy statistics sa-policy command.

show ip msdp policy statistics sa-policy peer-address {in | out} [vrf {vrf-name}]

Syntax Description

peer-address	IP address of the MSDP peer for the SA policy.
in	Specifies the input policy.
out	Specifies the output policy.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP SA policies:

switch(config)# show ip msdp policy statistics sa-policy 192.168.1.10 in

show ip msdp route

To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) cache, use the show ip msdp route command.

show ip msdp route [{source [group]} | {group [source]}] [asn] [peer peer] [detail] [vrf {vrf-name | all}]

Syntax Description

source	Source address for SA cache information.
group	(Optional) Group address for SA cache information.
asn	(Optional) Autonomous system (AS) number.
peer peer	(Optional) Specifies the IP address of a peer.
detail	(Optional) Displays detailed information.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip msdp sa-cache command is an alternative form of this command.

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the MSDP SA cache:

switch(config)# show ip msdp route

Related Commands

Command	Description
clear ip msdp route	Clears routes in the MSDP Source-Active cache.
show ip msdp sa-cache	Displays information about the MSDP SA cache.

show ip msdp rpf

To display information about the Multicast Source Discovery Protocol (MSDP) next-hop autonomous system (AS) on the Border Gateway Protocol (BGP) path to a rendezvous point (RP) address, use the show ip msdp rpf command.

show ip msdp rpf rp-address [vrf {vrf-name all}]

Syntax Description

rp-address	IP address of the RP.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP reverse path forwarding (RPF) peers:

switch(config)# show ip msdp rpf 192.168.1.10

show ip msdp sa-cache

To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) cache, use the show ip msdp sa-cache command.

show ip msdp sa-cache [{source [group]} | {group [source]}] [asn] [peer peer] [detail] [vrf {vrf-name | all}]

Syntax Description

source	Source address for SA cache information.
group	(Optional) Group address for SA cache information.
asn	(Optional) Autonomous system (AS) number.
peer peer	(Optional) Specifies the IP address of a peer.
detail	(Optional) Displays detailed information.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip msdp route command is an alternative form of this command.

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the MSDP SA cache:

switch(config)# show ip msdp sa-cache

Related Commands

Command	Description
clear ip msdp sa-cache	Clears routes in the MSDP Source-Active cache.
show ip msdp route	Displays information about the MSDP SA cache.

show ip msdp route

To display information about the Multicast Source Discovery Protocol (MSDP) Source-Active (SA) route cache, use the show ip msdp route command.

show ip msdp route [{source [group]} | {group [source]}] [asn] [peer peer] [detail] [vrf {vrf-name | all}]

Syntax Description

source	Source address for SA cache information.
group	(Optional) Group address for SA cache information.
asn	(Optional) Autonomous system (AS) number.
peer peer	(Optional) Specifies the IP address of a peer.
detail	(Optional) Displays detailed information.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

The show ip msdp route command is an alternative form of this command.

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the MSDP SA cache:

switch(config)# show ip msdp sa-cache

Related Commands

Command	Description
clear ip msdp sa-cache	Clears routes in the MSDP Source-Active cache.
show ip msdp route	Displays information about the MSDP SA cache.

show ip msdp sources

To display information about Multicast Source Discovery Protocol (MSDP) learned sources, use the show ip msdp sources command.

show ip msdp sources [vrf {vrf-name | all}]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about MSDP learned sources:

switch(config)# show ip msdp sources

show ip msdp summary

To display summary information about Multicast Source Discovery Protocol (MSDP) peers, use the show ip msdp summary command.

show ip msdp summary [vrf {vrf-name | all}]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display summary information about MSDP peers:

switch(config)# show ip msdp summary

show ip pim event-history

To display information in the IPv4 Protocol Independent Multicast (PIM) event history buffers, use the show ip pim event-history command.

show ip pim event-history {errors | msgs | statistics}

Syntax Description

errors	Displays events of type error.
msgs	Displays events of type msg.
statistics	Displays events of type statistics.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Examples

This example shows how to display information in the IPv4 PIM msgs event history buffer:

switch(config)# show ip pim event-history msgs

Msg events for PIM Process

1) Event:E_DEBUG, length:38, at 165671 usecs after Sat Apr 12 08:35:02 2008

    [100] : nvdb: transient thread created

2) Event:E_DEBUG, length:38, at 165018 usecs after Sat Apr 12 08:35:02 2008

    [100] : nvdb: create transcient thread

3) Event:E_DEBUG, length:79, at 165014 usecs after Sat Apr 12 08:35:02 2008

    [100] : comp-mts-rx opc - from sap 3061 cmd pim_show_internal_event_hist_com

mand

4) Event:E_DEBUG, length:35, at 63168 usecs after Sat Apr 12 08:34:25 2008

    [100] : nvdb: terminate transaction

5) Event:E_DEBUG, length:46, at 62809 usecs after Sat Apr 12 08:34:25 2008

    [100] : nvdb: pim_show_df_command returned 0x0

6) Event:E_DEBUG, length:38, at 62676 usecs after Sat Apr 12 08:34:25 2008

    [100] : nvdb: transient thread created

7) Event:E_DEBUG, length:38, at 61971 usecs after Sat Apr 12 08:34:25 2008

    [100] : nvdb: create transcient thread

8) Event:E_DEBUG, length:62, at 61966 usecs after Sat Apr 12 08:34:25 2008

    [100] : comp-mts-rx opc - from sap 3055 cmd pim_show_df_command

9) Event:E_DEBUG, length:50, at 771336 usecs after Sat Apr 12 06:14:41 2008

    [100] : nvdb: _cli_send_my_if_command returned 0x0

10) Event:E_DEBUG, length:63, at 771105 usecs after Sat Apr 12 06:14:41 2008

    [100] : comp-mts-rx opc - from sap 0 cmd _cli_send_my_if_command

<--Output truncated-->

switch(config)#

Related Commands

Command	Description
clear ip pim event-history	Clears the contents of the PIM event history buffers.
ip pim event-history	Configures the size of PIM event history buffers.

show ip pim group-range

To display information about the group ranges for IPv4 Protocol Independent Multicast (PIM), use the show ip pim group-range command.

show ip pim group-range [group] [vrf {vrf-name | all | default | management}]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM group ranges:

switch(config)# show ip pim group-range

PIM Group-Range Configuration for VRF "default"

Group-range        Mode      RP-address       Shared-tree-only range

232.0.0.0/8        SSM       -                -

switch(config)#

show ip pim interface

To display information about the enabled interfaces for IPv4 Protocol Independent Multicast (PIM), use the show ip pim interface command.

show ip pim interface [brief] [vrf {vrf-name | all | default | management}]

show ip pim interface ethernet {slot/port | port-channel channel-number[.sub_if-number] | vlan vlan-id}

Syntax Description

brief	(Optional) Specifies a brief format for display.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.
ethernet slot/port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if-number	(Optional) Subinterface number. The range is from 1 to 4093.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display brief information about IPv4 PIM-enabled interfaces:

switch# show ip pim interface brief

PIM Interface Status for VRF "default"

Interface            IP Address      PIM DR Address  Neighbor  Border

                                                     Count     Interface

Vlan100              192.0.2.252     192.0.2.252     0         no

port-channel2000     192.0.2.1       192.0.2.1       1         no

port-channel2001     192.0.2.8       192.0.2.8       1         no

Ethernet1/26         192.0.2.2       192.0.2.2       1         no

Ethernet2/5          192.0.2.3       192.0.2.3       1         no

Ethernet2/6          192.0.2.4       192.0.2.4       1         no

Ethernet2/7          192.0.2.5       192.0.2.5       1         no

Ethernet3/11         192.0.2.6       192.0.2.6       1         no

Ethernet3/12         192.0.2.7       192.0.2.7       1         no

switch#

This example shows how to display information about PIM-enabled interfaces:

switch# show ip pim interface ethernet 2/5

PIM Interface Status for VRF "default"

Ethernet2/5, Interface status: protocol-up/link-up/admin-up

  IP address: 192.0.2.3, IP subnet: 192.0.2.0/24

  PIM DR: 192.0.2.3, DR's priority: 1

  PIM neighbor count: 1

  PIM hello interval: 30 secs, next hello sent in: 00:00:20

  PIM neighbor holdtime: 105 secs

  PIM configured DR priority: 1

  PIM border interface: no

  PIM GenID sent in Hellos: 0x36a7d6d1

  PIM Hello MD5-AH Authentication: disabled

  PIM Neighbor policy: none configured

  PIM Join-Prune inbound policy: none configured

  PIM Join-Prune outbound policy: none configured

  PIM BFD enabled: no

  PIM Interface Statistics, last reset: never

    General (sent/received):

      Hellos: 454/453, JPs: 4/0, Asserts: 0/0

      Grafts: 0/0, Graft-Acks: 0/0

      DF-Offers: 0/0, DF-Winners: 0/0, DF-Backoffs: 0/0, DF-Passes: 0/0

    Errors:

      Checksum errors: 0, Invalid packet types/DF subtypes: 0/0

      Authentication failed: 0

      Packet length errors: 0, Bad version packets: 0, Packets from self: 0

      Packets from non-neighbors: 0

      JPs received on RPF-interface: 0

      (*,G) Joins received with no/wrong RP: 0/0

      (*,G)/(S,G) JPs received for SSM/Bidir groups: 0/0

      JPs filtered by inbound policy: 0

      JPs filtered by outbound policy: 0

switch#

show ip pim neighbor

To display information about IPv4 Protocol Independent Multicast (PIM) neighbors, use the show ip pim neighbor command.

show ip pim neighbor {[ethernet slot/port | port-channel channel-number[.sub_if-number] | vlan vlan-id] | [neighbor-addr]} [vrf {vrf-name | all | default | management}]

Syntax Description

ethernet slot/port	(Optional) Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	(Optional) Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if-number	(Optional) Subinterface number. The range is from 1 to 4093.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.
neighbor-addr	(Optional) IP address of a neighbor.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about PIM neighbors:

switch(config)# show ip pim neighbor

PIM Neighbor Status for VRF "default"

Neighbor        Interface            Uptime    Expires   DR       Bidir-  BFD

                                                         Priority Capable State

192.0.2.2       port-channel2000     03:43:40  00:01:21  1        no     n/a

192.0.2.9       port-channel2001     03:43:41  00:01:35  1        no     n/a

192.0.2.1       Ethernet1/26         03:43:44  00:01:33  1        no     n/a

192.0.2.2       Ethernet2/5          03:43:45  00:01:34  1        no     n/a

192.0.2.3       Ethernet2/6          03:43:45  00:01:19  1        no     n/a

192.0.2.4       Ethernet2/7          03:43:45  00:01:39  1        no     n/a

192.0.2.5       Ethernet3/11         03:43:46  00:01:35  1        no     n/a

192.0.2.6       Ethernet3/12         03:43:46  00:01:34  1        no     n/a

switch(config)#

show ip pim oif-list

To display information about IPv4 Protocol Independent Multicast (PIM) interfaces for a group, use the show ip pim oif-list command.

show ip pim oif-list group [source] [vrf {vrf-name | all | default | management}]

Syntax Description

group	Group address.
source	(Optional) Source address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display IPv4 PIM interfaces for a group:

switch(config)# show ip pim oif-list 232.0.0.0

PIM OIF-List for VRF default

(*, 232.0.0.0/8)

  Incoming interface: Null0, RPF nbr 0.0.0.0

  Timeout interval: 66 secs left

  Oif-list (count: 0):

  Timeout-list (count: 0):

  Immediate-list (count: 0):

  Immediate-timeout-list (count: 0):

  Assert-lost-list (count: 0):

switch(config)#

show ip pim policy statistics auto-rp

To display information about the Auto-RP policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics auto-rp command.

show ip pim policy statistics auto-rp {rp-candidate-policy | mapping-agent-policy} [vrf {vrf-name | all | default | management}]

Syntax Description

rp-candidate- policy	Specifies candidate-RP messages.
mapping- agent-policy	Specifies mapping agent messages.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM policy statistics:

switch(config)# show ip pim policy statistics auto-rp rp-candidate-policy

show ip pim policy statistics bsr

To display information about the bootstrap router (BSR) policy statistics for IPv4 Protocol Independent multicast (PIM), use the show ip pim policy statistics bsr command.

show ip pim policy statistics bsr {bsr-policy | rp-candidate-policy} [vrf {vrf-name | all | default | management}]

Syntax Description

bsr-policy	Specifies BSR messages.
rp-candidate- policy	Specifies candidate-RP messages.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM policy statistics:

switch(config)# show ip pim policy statistics bsr bsr-policy

show ip pim policy statistics jp-policy

To display information about the join-prune policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics jp-policy command.

show ip pim policy statistics jp-policy {ethernet slot/port | port-channel channel-number[.sub_if-number] | vlan vlan-id}

Syntax Description

ethernet slot/port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if-number	(Optional) Subinterface number. The range is from 1 to 4093.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about PIM policy statistics:

switch(config)# show ip pim policy statistics jp-policy ethernet 2/12

show ip pim policy statistics neighbor-policy

To display information about the neighbor policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics neighbor-policy command.

show ip pim policy statistics neighbor-policy {ethernet slot/port | port-channel channel-number[.sub_if-number] | vlan vlan-id}

Syntax Description

ethernet slot/port	Specifies the Ethernet interface and the slot number and port number. The slot number is from 1 to 255, and the port number is from 1 to 128.
port-channel number	Specifies the EtherChannel interface and EtherChannel number. The range is from 1 to 4096.
sub_if-number	(Optional) Subinterface number. The range is from 1 to 4093.
vlan vlan-id	Specifies the VLAN. The range is from 1 to 4094.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM policy statistics:

switch(config)# show ip pim policy statistics neighbor-policy ethernet 2/12

show ip pim policy statistics register-policy

To display information about the register policy statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim policy statistics register-policy command.

show ip pim policy statistics register-policy [vrf {vrf-name | all | default | management}]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about PIM policy statistics:

switch(config)# show ip pim policy statistics register-policy vrf all

show ip pim route

To display information about the routes for IPv4 Protocol Independent Multicast (PIM), use the show ip pim route command.

show ip pim route {source group | group [source]} [vrf {vrf-name | all | default | management}]

Syntax Description

source	Source address.
group	Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies that all VRF entries be cleared from the IPv4 multicast routing table.
default	Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.
management	Specifies that the management VRF entry be cleared from the IPv4 multicast routing table.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display IPv4 PIM routes:

switch(config)# show ip pim route 232.0.0.0

PIM Routing Table for VRF "default" - 1 entries

(*, 232.0.0.0/8), expires 00:02:15

  Incoming interface: Null0, RPF nbr 0.0.0.0

  Oif-list:       (0) 00000000, timeout-list: (0) 00000000

  Immediate-list: (0) 00000000, timeout-list: (0) 00000000

  Timeout-interval: 3, JP-holdtime round-up: 3

switch(config)#

show ip pim rp

To display information about the rendezvous points (RPs) for IPv4 Protocol Independent Multicast (PIM), use the show ip pim rp command.

show ip pim rp [group] [vrf {vrf-name | all | default | management}]

Syntax Description

group	(Optional) Group address.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM RPs:

switch(config)# show ip pim rp

PIM RP Status Information for VRF "default"

BSR disabled

Auto-RP disabled

BSR RP Candidate policy: None

BSR RP policy: None

Auto-RP Announce policy: None

Auto-RP Discovery policy: None

switch(config)#

show ip pim rp-hash

To display information about the RP-hash values for IPv4 Protocol Independent Multicast (PIM), use the show ip pim rp-hash command.

show ip pim rp-hash group [vrf {vrf-name | all | default | management}]

Syntax Description

group	Group address for RP lookup.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM RP-hash values:

switch(config)# show ip pim rp-hash 224.1.1.1

show ip pim statistics

To display information about the packet counter statistics for IPv4 Protocol Independent Multicast (PIM), use the show ip pim statistics command.

show ip pim statistics [vrf {vrf-name | all | default | management}]

Syntax Description

vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM statistics (if PIM is not in vPC mode, the vPC statistics are not displayed):

switch(config)# show ip pim statistics

PIM Global Counter Statistics for VRF:default, last reset: never

  Register processing (sent/received):

    Registers: 0/0, Null registers: 0/0, Register-Stops: 0/0

    Registers received and not RP: 0

    Registers received for SSM groups: 0

  BSR processing (sent/received):

    Bootstraps: 0/0, Candidate-RPs: 0/0

    BSs from non-neighbors: 0, BSs from border interfaces: 0

    BS length errors: 0, BSs which RPF failed: 0

    BSs received but not listen configured: 0

    Cand-RPs from border interfaces: 0

    Cand-RPs received but not listen configured: 0

  Auto-RP processing (sent/received):

    Auto-RP Announces: 0/0, Auto-RP Discoveries: 0/0

    Auto-RP RPF failed: 0, Auto-RP from border interfaces: 0

    Auto-RP invalid type: 0, Auto-RP TTL expired: 0

    Auto-RP received but not listen configured: 0

  General errors:

    Control-plane RPF failure due to no route found: 0

    Data-plane RPF failure due to no route found: 0

    Data-plane no multicast state found: 0

    Data-plane create route state count: 0

  vPC packet stats:

    assert requests sent: 0

    assert requests received: 0

    assert request send error: 0

    assert response sent: 0

    assert response received: 0

    assert response send error: 0

    assert stop sent: 0

    assert stop received: 0

    assert stop send error: 0

    rpf-source metric requests sent: 0

    rpf-source metric requests received: 0

    rpf-source metric request send error: 0

    rpf-source metric response sent: 0

    rpf-source metric response received: 0

    rpf-source metric response send error: 0

    rpf-source metric rpf change trigger sent: 0

    rpf-source metric rpf change trigger received: 0

    rpf-source metric rpf change trigger send error: 0

switch(config)#

show ip pim vrf

To display information about IPv4 Protocol Independent Multicast (PIM) by virtual routing and forwarding (VRF) instance, use the show ip pim vrf command.

show ip pim vrf [vrf-name | all | default | detail | management]

Syntax Description

vrf-name	(Optional) VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	(Optional) Specifies all VRFs.
default	(Optional) Specifies the default VRF.
detail	(Optional) Displays detailed PIM VRF information.
management	(Optional) Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM by VRF:

switch(config)# show ip pim vrf

PIM Enabled VRF

VRF Name              VRF      Table       Interface  BFD

                      ID       ID          Count      Enabled

default               1        0x00000001  1          no

switch(config)#

This example shows how to display the detailed information about IPv4 PIM by VRF:

switch# show ip pim vrf detail 

PIM Enabled VRF

VRF Name              VRF      Table       Interface  BFD

                      ID       ID          Count      Enabled

default               1        0x00000001  1          no

  State Limit: None

  Register Rate Limit: none

  Shared tree ranges: none

  (S,G)-expiry timer: not configured

    (S,G)-list policy: none

    (S,G)-expiry timer config version 0, active version 0

  Pre-build SPT for all (S,G)s in VRF: disabled

switch#

show ip static-route

To display static routes from the unicast Routing Information Base (RIB), use the show ip static-route command.

show ip static-route [vrf {vrf-name | all | default | management}]

Syntax Description

vrf vrf-name	(Optional) Specifies the virtual routing and forwarding (VRF) context name. The name can be any case-sensitive, alphanumeric string up to 32 characters.
all	(Optional) Specifies all VRF instances.
default	(Optional) Specifies the default VRF.
management	(Optional) Specifies the management VRF.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Examples

This example shows how to display the static routes:

switch(config)# show ip static-route

Static-route for VRF "default"(1)

IPv4 Unicast Static Routes:

Total number of routes: 0, unresolved: 0

switch(config)#

Related Commands

Command	Description
ip route	Configures a static route.

show routing ip multicast event-history

To display information in the IPv4 Multicast Routing Information Base (MRIB) event history buffers, use the show routing ip multicast event-history command.

show routing ip multicast event-history {cli | errors | mfdm-debugs | mfdm-stats | msgs | rib | statistics | vrf}

Syntax Description

cli	Displays the event history buffer of type CLI.
errors	Displays the event history buffer of type errors.
mfdm-debugs	Displays the event history buffer of type multicast FIB distribution (MFDM).
mfdm-stats	Displays the event history buffer of type MFDM sum.
msgs	Displays the event history buffer of type msgs.
rib	Displays the event history buffer of type RIB.
statistics	Displays information about the event history buffers.
vrf	Displays the event history buffer of type virtual routing and forwarding (VRF).

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Examples

This example shows how to display information in the MRIB msgs event history buffer:

switch(config)# show routing ip multicast event-history msgs

Msg events for MRIB Process

1) Event:E_DEBUG, length:38, at 932956 usecs after Sat Apr 12 09:09:41 2008

    [100] : nvdb: transient thread created

2) Event:E_DEBUG, length:38, at 932269 usecs after Sat Apr 12 09:09:41 2008

    [100] : nvdb: create transcient thread

3) Event:E_DEBUG, length:75, at 932264 usecs after Sat Apr 12 09:09:41 2008

    [100] : comp-mts-rx opc - from sap 3210 cmd mrib_internal_event_hist_command

4) Event:E_MTS_RX, length:60, at 362578 usecs after Sat Apr 12 09:08:51 2008

    [RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X000F217E, Ret:SUCCESS

    Src:0x00000101/214, Dst:0x00000101/1203, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x000F217B, Sync:NONE, Payloadsize:148

    Payload:

    0x0000:  01 00 00 00 05 00 01 00 00 04 00 00 00 00 00 00

5) Event:E_MTS_RX, length:60, at 352493 usecs after Sat Apr 12 09:07:51 2008

    [RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X000F188B, Ret:SUCCESS

    Src:0x00000101/214, Dst:0x00000101/1203, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x000F1888, Sync:NONE, Payloadsize:148

    Payload:

    0x0000:  01 00 00 00 05 00 01 00 00 04 00 00 00 00 00 00

6) Event:E_MTS_RX, length:60, at 342641 usecs after Sat Apr 12 09:06:51 2008

    [RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X000F0DF0, Ret:SUCCESS

    Src:0x00000101/214, Dst:0x00000101/1203, Flags:None

    HA_SEQNO:0X00000000, RRtoken:0x000F0DED, Sync:NONE, Payloadsize:148

    Payload:

    0x0000:  01 00 00 00 05 00 01 00 00 04 00 00 00 00 00 00

7) Event:E_MTS_RX, length:60, at 332954 usecs after Sat Apr 12 09:05:51 2008

    [RSP] Opc:MTS_OPC_MFDM_V4_ROUTE_STATS(75785), Id:0X000F0493, Ret:SUCCESS

<--Output truncated-->

switch(config)#

Related Commands

Command	Description
ip routing multicast event-history	Configures the size of the IPv4 MRIB event history buffers.
clear ip routing multicast event-history	Clears information in the IPv4 MRIB event history buffers.

show routing multicast

To display information about IPv4 multicast routes, use the show routing multicast command.

show routing [ip | ipv4] multicast [vrf {vrf-name | all | default | management}]
{{source group} | {group [source]}}

Syntax Description

ip	(Optional) Specifies IPv4 routes.
ipv4	(Optional) Specifies IPv4 routes.
vrf	(Optional) Applies to a virtual routing and forwarding (VRF) instance.
vrf-name	VRF name. The name can be a maximum of 32 alphanumeric characters and is case sensitive.
all	Specifies all VRFs.
default	Specifies the default VRF.
management	Specifies the management VRF.
source	Source address for routes.
group	Group address for routes.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 multicast routes:

switch(config)# show routing multicast

IP Multicast Routing Table for VRF "default"

(*, 232.0.0.0/8), uptime: 05:11:19, pim ip

  Incoming interface: Null, RPF nbr: 0.0.0.0

  Outgoing interface list: (count: 0)

switch(config)#

show routing multicast clients

To display information about IPv4 multicast routing clients, use the show routing multicast clients command.

show routing [ip | ipv4] multicast clients [client-name]

Syntax Description

ip	(Optional) Specifies IPv4 multicast clients.
ipv4	(Optional) Specifies IPv4 multicast clients.
client-name	(Optional) One of the following multicast routing client names: •mrib •igmp •static •msdp •ip •pim

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 multicast clients:

switch(config)# show routing multicast clients pim

IP Multicast Routing Client information

Client: pim, client-id: 5, pid: 5296, mts-sap: 310

  Shared-memory: pim, Notifications: joins prunes rpf delete repopulate

  Protocol is ssm owner, bidir owner, shared-only mode owner,

  Join notifications:         sent 1, fail 0, ack rcvd 1

  Prune notifications:        sent 0, fail 0, ack rcvd 0

  RPF notifications:          sent 0, fail 0, ack rcvd 0

  Delete notifications:       sent 0, fail 0, ack rcvd 0

  Repopulate notifications:   sent 0, fail 0, ack rcvd 0

  Clear mroute notifications: sent 0, fail 0

  Add route requests:         rcvd 2, ack sent 2, ack fail 0

  Delete route requests:      rcvd 0, ack sent 0, ack fail 0

  Update route requests:      rcvd 0, ack sent 0, ack fail 0

  MTS update route requests:  rcvd 0, ack sent 0, ack fail 0

   Per VRF notification markers: 1

switch(config)#

show running-config igmp

To display information about the running-system configuration for IGMP, use the show running-config igmp command.

show running-config igmp [all]

Syntax Description

all	(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the IGMP running-system configuration:

switch(config)# show running-config igmp

!Command: show running-config igmp

!Time: Fri May  2 08:05:08 2008

version 5.0(3)N1(1)

interface Ethernet1/5

  ip igmp static-oif 230.0.0.0

switch(config)#

show running-config msdp

To display information about the running-system configuration for Multicast Source Discovery Protocol (MSDP), use the show running-config msdp command.

show running-config msdp [all]

Syntax Description

all	(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the MSDP running-system configuration:

switch(config)# show running-config msdp

!Command: show running-config msdp

!Time: Sat Apr 12 09:14:49 2008

version 5.0(3)N1(1)

feature msdp

switch(config)# 

show running-config pim

To display information about the running-system configuration for IPv4 Protocol Independent Multicast (PIM), use the show running-config pim command.

show running-config pim [all]

Syntax Description

all	(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the IPv4 PIM running-system configuration:

switch(config)# show running-config pim

!Command: show running-config pim

!Time: Sat Apr 12 09:15:11 2008

version 5.0(3)N1(1)

feature pim

ip pim ssm range 232.0.0.0/8

interface Vlan20

  ip pim sparse-mode

switch(config)#

show startup-config igmp

To display information about the startup-system configuration for IGMP, use the show startup-config igmp command.

show startup-config igmp [all]

Syntax Description

all	(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the IGMP startup-system configuration:

switch(config)# show startup-config igmp

show startup-config msdp

To display information about the startup-system configuration for Multicast Source Discovery Protocol (MSDP), use the show startup-config msdp command.

show startup-config msdp [all]

Syntax Description

all	(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the startup-system configuration for MSDP:

switch(config)# show startup-config msdp

show startup-config pim

To display information about the startup-system configuration for IPv4 Protocol Independent Multicast (PIM), use the show startup-config pim command.

show startup-config pim [all]

Syntax Description

all	(Optional) Displays configured and default information.

Command Default

None

Command Modes

Any command mode

Command History

Release	Modification
5.0(3)N1(1)	This command was introduced.

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about the startup-system configuration for IPv4 PIM:

switch(config)# show startup-config pim