Table Of Contents

Show Commands

show diagnostic result fex

show environment fex

show fex

show fex detail

show fex transceiver

show fex version

show interface fex-fabric

show interface fex-intf

show interface transceiver fex-fabric

show inventory fex

show locator-led

show module fex

show provision

show queuing interface

show running-config exclude-provision

show running-config fex

show sprom fex

show startup-config exclude-provision

show system reset-reason fex

show version fex

Show Commands

---

This chapter describes the Cisco NX-OS show commands used to manage a Cisco Nexus 2000 Series Fabric Extender from a Cisco Nexus 5500 switch.

show diagnostic result fex

To display the results from the diagnostic tests for a Fabric Extender chassis, use the show diagnostic result fex command.

show diagnostic result fex chassis_ID

Syntax Description

chassis_ID

Fabric Extender chassis ID. The chassis ID range is from 100 to 199.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the results from the diagnostic tests for a Fabric Extender:

switch# show diagnostic result fex 100 

FEX-100: 48x1GE/Supervisor  SerialNo   : JAF1237ABSE

Overall Diagnostic Result for FEX-100  : OK

Test results: (. = Pass, F = Fail, U = Untested)

TestPlatform:

0)              SPROM: ---------------> .

1)          MV88E6095: ---------------> .

2)                Fan: ---------------> .

3)       Power Supply: ---------------> .

4) Temperature Sensor: ---------------> .

TestForwardingPorts:

Eth    1  2  3  4  5  6  7  8  9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Port ------------------------------------------------------------------------

       .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .

Eth   25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

Port ------------------------------------------------------------------------

       .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .

TestFabricPorts:

Fabric 1  2  3  4

Port ------------

       .  .  .  .

switch#

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show environment fex

To display the environmental sensor status, use the show environment fex command.

show environment fex {all | chassis_ID} [temperature | power | fan]

Syntax Description

all	Displays information for all Fabric Extender chassis.
chassis_ID	Fabric Extender chassis ID. The chassis ID range is from 100 to 199.
temperature	(Optional) Displays temperature sensor information.
power	(Optional) Displays power capacity and power distribution information.
fan	(Optional) Displays fan information.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the environmental sensor status for a Fabric Extender:

switch# show environment fex 100 

Temperature Fex 100:

-----------------------------------------------------------------

Module   Sensor     MajorThresh   MinorThres   CurTemp     Status

                    (Celsius)     (Celsius)    (Celsius)

-----------------------------------------------------------------

1        Outlet-1   63            45           26          ok

1        Inlet-1    65            55           27          ok

1        Die-1      100           85           38          ok

Fan Fex: 100:

------------------------------------------------------

Fan             Model                Hw         Status

------------------------------------------------------

Chassis         N2K-C2248-FAN        --         ok

PS-1            N2200-PAC-400W       --         ok

PS-2            N2200-PAC-400W       --         failure

Power Supply Fex 100:

---------------------------------------------------------------------------

Voltage: 12 Volts

-----------------------------------------------------

PS  Model                Power       Power     Status

                         (Watts)     (Amp)

-----------------------------------------------------

1   N2200-PAC-400W        396.00     33.00     ok

2   --                        --        --     fail/shutdown

Mod Model                Power     Power       Power     Power       Status

                         Requested Requested   Allocated Allocated

                         (Watts)   (Amp)       (Watts)   (Amp)

--- -------------------  -------   ----------  --------- ----------  ----------

1    N2K-C2248TP-1GE     55.20     4.60        55.20     4.60        powered-up

Power Usage Summary:

--------------------

Power Supply redundancy mode:                 redundant

Power Supply redundancy operational mode:     Non-redundant

Total Power Capacity                              396.00 W

Power reserved for Supervisor(s)                   55.20 W

Power currently used by Modules                     0.00 W

                                                -------------

Total Power Available                             340.80 W

                                                -------------

switch#

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show fex

To display information about a specific Fabric Extender or all attached chassis, use the show fex command.

show fex [chassis_ID [detail]]

Syntax Description

chassis_ID	(Optional) Fabric Extender chassis ID. The chassis ID range is from 100 to 199.
detail	(Optional) Displays a detailed listing.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display information about all attached Fabric Extender chassis:

switch# show fex 

FEX         FEX           FEX                       FEX

Number    Description      State            Model            Serial

------------------------------------------------------------------------

100        FEX0100                Online    N2K-C2248PQ-10GE   FOC1616R00Q

---       --------            Discovered     N2K-C2248TP-1GE   SSI16020453

---       --------            Discovered     N2K-C2232P-10GE   SSI133106K6

switch# 

This example shows how to display information about a specific Fabric Extender chassis:

switch# show fex 100 

switch(config-slot)# show fex 100

FEX: 100 Description: FEX0100   state: Online

  FEX version: 6.0(2)N1(1) [Switch version: 6.0(2)N1(1)]

  Extender Serial: FOC1616R00Q

  Extender Model: N2K-C2248PQ-10GE,  Part No: 73-14775-02

  Pinning-mode: static    Max-links: 1

  Fabric port for control traffic: Eth2/3

  FCoE Admin: false

  FCoE Oper: true

  FCoE FEX AA Configured: false

  Fabric interface state:

    Po100 - Interface Up. State: Active

    Eth2/1 - Interface Up. State: Active

    Eth2/2 - Interface Up. State: Active

    Eth2/3 - Interface Up. State: Active

    Eth2/4 - Interface Up. State: Active

This example shows how to display the detailed information about all attached Fabric Extender chassis:

switch# show fex detail 

show fex detail

FEX: 100 Description: FEX0100   state: Online

  FEX version: 6.0(2)N1(1) [Switch version: 6.0(2)N1(1)]

  FEX Interim version: 6.0(2)N1(1)

  Switch Interim version: 6.0(2)N1(1)

  Extender Serial: FOC1616R00Q

  Extender Model: N2K-C2248PQ-10GE,  Part No: 73-14775-02

  Card Id: 207, Mac Addr: a4:18:75:37:67:42, Num Macs: 64

  Module Sw Gen: 12594  [Switch Sw Gen: 21]

  post level: complete

pinning-mode: static    Max-links: 1

  Fabric port for control traffic: Eth2/3

  FCoE Admin: false

  FCoE Oper: true

  FCoE FEX AA Configured: false

  Fabric interface state:

    Po100 - Interface Up. State: Active

    Eth2/1 - Interface Up. State: Active

    Eth2/2 - Interface Up. State: Active

    Eth2/3 - Interface Up. State: Active

    Eth2/4 - Interface Up. State: Active

  Fex Port        State  Fabric Port

Eth100/1/1  Up         None

       Eth100/1/2  Up         Po100

       Eth100/1/3  Up         Po100

       Eth100/1/4  Up         Po100

       Eth100/1/5  Up         Po100

       Eth100/1/6  Up         Po100

       Eth100/1/7  Up         Po100

       Eth100/1/8  Up         Po100

       Eth100/1/9  Up         Po100

      Eth100/1/10  Up         Po100

      Eth100/1/11  Up         Po100

      Eth100/1/12  Up         Po100

      Eth100/1/13  Up         Po100

      Eth100/1/14  Up         Po100

      Eth100/1/15  Up         Po100

      Eth100/1/16  Up         Po100

      Eth100/1/17  Down        None

      Eth100/1/18  Down        None

      Eth100/1/19  Down        None

      Eth100/1/20  Down        None

      Eth100/1/21  Up         Po100

      Eth100/1/22  Up         Po100

      Eth100/1/23  Up         Po100

      Eth100/1/24  Up         Po100

      Eth100/1/25  Up         Po100

      Eth100/1/26  Up         Po100

      Eth100/1/27  Down        None

      Eth100/1/28  Down        None

      Eth100/1/29  Up         Po100

      Eth100/1/30  Up         Po100

      Eth100/1/31  Up         Po100

      Eth100/1/32  Up         Po100

      Eth100/1/33  Up         Po100

      Eth100/1/34  Up         Po100

      Eth100/1/35  Up         Po100

      Eth100/1/36  Up         Po100

      Eth100/1/37  Up         Po100

      Eth100/1/38  Up         Po100

      Eth100/1/39  Up         Po100

      Eth100/1/40  Up         Po100

      Eth100/1/41  Up         Po100

      Eth100/1/42  Up         Po100

      Eth100/1/43  Up         Po100

      Eth100/1/44  Up         Po100

      Eth100/1/45  Up         Po100

      Eth100/1/46  Up         Po100

      Eth100/1/47  Down        None

      Eth100/1/48  Down        None

Logs:

01/13/2013 03:10:36.646339: Module register received

01/13/2013 03:10:36.653063: Image Version Mismatch

01/13/2013 03:10:36.654323: Registration response sent

01/13/2013 03:10:36.654653: Requesting satellite to download image

01/13/2013 03:18:32.807440: Image preload successful.

01/13/2013 03:18:34.914876: Deleting route to FEX

01/13/2013 03:18:34.925056: Module disconnected

01/13/2013 03:18:34.926943: Module Offline

01/13/2013 03:18:34.929419: Deleting route to FEX

01/13/2013 03:18:34.936603: Module disconnected

01/13/2013 03:18:34.940691: Offlining Module

01/13/2013 03:20:05.822920: Deleting route to FEX

01/13/2013 03:20:05.829998: Module disconnected

01/13/2013 03:20:05.832442: Offlining Module

01/13/2013 03:20:23.566625: Module register received

01/13/2013 03:20:23.569473: Registration response sent

01/13/2013 03:20:23.868221: create module inserted event.

01/13/2013 03:20:23.869315: Module Online Sequence

01/13/2013 03:20:36.461303: Module Online

01/14/2013 22:21:54.969375: Deleting route to FEX

01/14/2013 22:21:54.981504: Module disconnected

01/14/2013 22:21:54.983913: Offlining Module

01/14/2013 22:21:54.984853: Module Offline Sequence

01/14/2013 22:22:01.715915: Module Offline

01/14/2013 22:22:01.757028: Deleting route to FEX

01/14/2013 22:22:01.764842: Module disconnected

01/14/2013 22:22:01.767241: Offlining Module

01/14/2013 22:23:45.341774: Module register received

01/14/2013 22:23:45.344482: Registration response sent

01/14/2013 22:23:49.813218: create module inserted event.

01/14/2013 22:23:49.814317: Module Online Sequence

01/14/2013 22:23:58.120815: Module Online

switch# 

Related Commands

Command	Description
fex	Creates a Fabric Extender and enters fabric extender configuration mode.

show fex detail

To display detailed information about a specific Fabric Extender or all attached chassis, use the show fex detail command.

show fex detail

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display detailed information about all attached Fabric Extender chassis:

switch# show fex detail 

FEX: 100 Description: FEX0100   state: Online

  FEX version: 4.2(1)N1(1) [Switch version: 4.2(1)N1(1)]

  FEX Interim version: 4.2(1)N1(0.326)

  Switch Interim version: 4.2(1)N1(0.326)

  Extender Model: N5K-C5110T-BF-1GE,  Extender Serial: JAF1237ABSE

  Part No: 73-12009-02

  Card Id: 70, Mac Addr: 00:0d:ec:b1:13:02, Num Macs: 64

  Module Sw Gen: 12594  [Switch Sw Gen: 21]

  post level: complete

 pinning-mode: static    Max-links: 1

  Fabric port for control traffic: Eth3/4

  Fabric interface state:

    Po12 - Interface Up. State: Active

    Eth3/3 - Interface Up. State: Active

    Eth3/4 - Interface Up. State: Active

  Fex Port        State  Fabric Port  Primary Fabric

       Eth100/1/1    Up        Po12        Po12

       Eth100/1/2    Up        Po12        Po12

       Eth100/1/3    Up        Po12        Po12

       Eth100/1/4    Up        Po12        Po12

       Eth100/1/5    Up        Po12        Po12

       Eth100/1/6    Up        Po12        Po12

       Eth100/1/7    Up        Po12        Po12

       Eth100/1/8    Up        Po12        Po12

       Eth100/1/9    Up        Po12        Po12

      Eth100/1/10    Up        Po12        Po12

      Eth100/1/11    Up        Po12        Po12

      Eth100/1/12    Up        Po12        Po12

      Eth100/1/13    Up        Po12        Po12

      Eth100/1/14    Up        Po12        Po12

      Eth100/1/15    Up        Po12        Po12

      Eth100/1/16    Up        Po12        Po12

      Eth100/1/17    Up        Po12        Po12

      Eth100/1/18    Up        Po12        Po12

      Eth100/1/19    Up        Po12        Po12

      Eth100/1/20    Up        Po12        Po12

      Eth100/1/21    Up        Po12        Po12

      Eth100/1/22    Up        Po12        Po12

      Eth100/1/23    Up        Po12        Po12

      Eth100/1/24    Up        Po12        Po12

      Eth100/1/25    Up        Po12        Po12

      Eth100/1/26    Up        Po12        Po12

      Eth100/1/27    Up        Po12        Po12

      Eth100/1/28    Up        Po12        Po12

      Eth100/1/29    Up        Po12        Po12

      Eth100/1/30    Up        Po12        Po12

      Eth100/1/31    Up        Po12        Po12

      Eth100/1/32    Up        Po12        Po12

      Eth100/1/33  Down        Po12        Po12

      Eth100/1/34  Down        Po12        Po12

      Eth100/1/35  Down        Po12        Po12

      Eth100/1/36  Down        Po12        Po12

      Eth100/1/37  Down        Po12        Po12

      Eth100/1/38  Down        Po12        Po12

      Eth100/1/39  Down        Po12        Po12

      Eth100/1/40    Up        Po12        Po12

      Eth100/1/41    Up        Po12        Po12

      Eth100/1/42    Up        Po12        Po12

      Eth100/1/43    Up        Po12        Po12

      Eth100/1/44    Up        Po12        Po12

      Eth100/1/45    Up        Po12        Po12

      Eth100/1/46    Up        Po12        Po12

      Eth100/1/47    Up        Po12        Po12

      Eth100/1/48    Up        Po12        Po12

Logs:

04/16/2010 05:05:23.441707: Module register received

04/16/2010 05:05:23.442886: Registration response sent

04/16/2010 05:05:23.551846: Module Online Sequence

04/16/2010 05:05:56.520856: Module Online

04/16/2010 05:29:38.526605: Deleting route to FEX

04/16/2010 05:29:38.536055: Module disconnected

04/16/2010 05:29:38.537686: Offlining Module

04/16/2010 05:29:38.538260: Module Offline Sequence

04/16/2010 05:29:53.646254: Module Offline

04/16/2010 05:29:54.178401: Deleting route to FEX

04/16/2010 05:29:54.184092: Module disconnected

04/16/2010 05:29:54.186230: Offlining Module

04/16/2010 05:31:13.784346: Module register received

04/16/2010 05:31:13.785410: Registration response sent

04/16/2010 05:31:15.676906: Module Online Sequence

04/16/2010 05:31:50.492714: Module Online

04/16/2010 05:32:18.388033: Deleting route to FEX

04/16/2010 05:32:18.393579: Module disconnected

04/16/2010 05:32:18.394845: Offlining Module

04/16/2010 05:32:18.395412: Module Offline Sequence

04/16/2010 05:32:30.336790: Module Offline

04/16/2010 05:32:30.683558: Deleting route to FEX

04/16/2010 05:32:30.690042: Module disconnected

04/16/2010 05:32:30.692101: Offlining Module

04/16/2010 05:33:42.781911: Module register received

04/16/2010 05:33:42.783432: Registration response sent

04/16/2010 05:33:52.542824: Module Online Sequence

04/16/2010 05:34:33.483417: Module Online

<---output truncated--->

switch#

Related Commands

Command	Description
fex	Creates a Fabric Extender and enters fabric extender configuration mode.
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show fex transceiver

To display information about the transceiver connecting a Fabric Extender to the Cisco Nexus 5500 switch, use the show fex transceiver command.

show fex chassis_ID transceiver [calibration | detail]

Syntax Description

chassis_ID	Fabric Extender chassis ID. The chassis ID range is from 100 to 199.
calibration	(Optional) Displays detailed calibration information about the transceiver.
detail	(Optional) Displays detailed diagnostic information about the transceiver.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display information about the transceiver that connects a Fabric Extender to the Cisco Nexus 5500 switch:

switch# show fex 101 transceiver 

Fex Uplink: 1

Fabric Port: Ethernet3/5

    sfp is present

    name is CISCO-AVAGO

    part number is SFBR-7700SDZ

    revision is B4

    serial number is AGD113921ZR

    nominal bitrate is 10300 MBits/sec

    Link length supported for 50/125mm fiber is 82 m(s)

    Link length supported for 62.5/125mm fiber is 26 m(s)

    cisco id is --

    cisco extended id number is 4

Fex Uplink: 2

Fabric Port: Ethernet3/6

    sfp is present

    name is CISCO-AVAGO

    part number is SFBR-7700SDZ

    revision is B4

    serial number is AGD113422LS

    nominal bitrate is 10300 MBits/sec

    Link length supported for 50/125mm fiber is 82 m(s)

    Link length supported for 62.5/125mm fiber is 26 m(s)

    cisco id is --

    cisco extended id number is 4

Fex Uplink: 3

Fabric Port: --

    sfp is present

    name is CISCO-AVAGO

    part number is SFBR-7700SDZ

    revision is B4

    serial number is AGD11392258

    nominal bitrate is 10300 MBits/sec

    Link length supported for 50/125mm fiber is 82 m(s)

    Link length supported for 62.5/125mm fiber is 26 m(s)

--More--

switch# 

Related Commands

Command	Description
fex	Creates a Fabric Extender and enters fabric extender configuration mode.

show fex version

To display the version information about a Fabric Extender, use the show fex version command.

show fex chassis_ID version

Syntax Description

chassis_ID

Fabric Extender chassis ID. The chassis ID range is from 100 to 199.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the version information about a Fabric Extender:

switch# show fex 101 version 

Software

  Bootloader version:           1.9

  System boot mode:             primary

  System image version:         6.0(2)N1(1) [build 6.0(2)N1(1)]

Hardware

  Module:                       Fabric Extender 48x10GE + 4x40GE Module

  CPU:                          Motorola, e500v2, core 0

  Serial number:                FOC16150CN1

  Bootflash:                    unlocked

Kernel uptime is 0 day(s), 1 hour(s), 28 minutes(s), 28 second(s)

Last reset at unknown time

  Reason: Unknown

  Service:

switch#        

Related Commands

Command	Description
fex	Creates a Fabric Extender and enters fabric extender configuration mode.

show interface fex-fabric

To display all Fabric Extender fabric interfaces, use the show interface fex-fabric command.

show interface fex-fabric

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display all Fabric Extender fabric interfaces:

switch# show interface fex-fabric 

     Fabric      Fabric       Fex                FEX

Fex  Port      Port State    Uplink    Model         Serial

---------------------------------------------------------------

---    Eth1/6    Discovered     2    N2K-C2232P-10GE  SSI133106K6

---    Eth1/7    Discovered     3    N2K-C2248TP-1GE  SSI16020453

---   Eth1/10    Discovered     2    N2K-C2248TP-1GE  SSI16020453

100    Eth2/1        Active     5    N2K-C2248PQ-10GE  FOC1616R00Q

100    Eth2/2        Active     6    N2K-C2248PQ-10GE  FOC1616R00Q

100    Eth2/3        Active     7    N2K-C2248PQ-10GE  FOC1616R00Q

100    Eth2/4        Active     8    N2K-C2248PQ-10GE  FOC1616R00Qswitch#

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show interface fex-intf

To display the host interfaces pinned to a fabric interface, use the show interface fex-intf command.

show interface interface fex-intf

Syntax Description

interface

Ethernet or EtherChannel interface.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the host interfaces pinned to an Ethernet fabric interface on the parent switch:

switch# show interface ethernet 1/1 fex-intf 

This example shows how to display the host interfaces pinned to an EtherChannel fabric interface on the parent switch:

switch# show interface port-channel 1 fex-intf 

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show interface transceiver fex-fabric

To display information about all transceivers connected to fabric interfaces, use the show interface transceiver fex-fabric command.

show interface transceiver fex-fabric [calibration | detail]

Syntax Description

calibration	(Optional) Displays detailed calibration information about the transceiver.
detail	(Optional) Displays detailed diagnostic information about the transceiver.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display information about all transceivers that connect to fabric interfaces:

switch# show interface transceiver fex-fabric 

Ethernet1/5

    sfp is present

    name is CISCO-MOLEX INC

    part number is 74752-9025

    revision is A

    serial number is MOC12302468

    nominal bitrate is 12000 MBits/sec

    Link length supported for 50/125mm fiber is 0 m(s)

    Link length supported for 62.5/125mm fiber is 0 m(s)

    cisco id is --

    cisco extended id number is 4

Ethernet1/6

    sfp is present

    name is CISCO-MOLEX INC

    part number is 74752-9025

    revision is A

    serial number is MOC12260214

    nominal bitrate is 12000 MBits/sec

    Link length supported for 50/125mm fiber is 0 m(s)

    Link length supported for 62.5/125mm fiber is 0 m(s)

    cisco id is --

    cisco extended id number is 4

Ethernet1/7

    sfp is present

    name is CISCO-MOLEX INC

    part number is 74752-9025

    revision is A

    serial number is MOC12301888

    nominal bitrate is 12000 MBits/sec

    Link length supported for 50/125mm fiber is 0 m(s)

    Link length supported for 62.5/125mm fiber is 0 m(s)

    cisco id is --

    cisco extended id number is 4

Ethernet1/8

    sfp is present

    name is CISCO-MOLEX INC

--More--

switch# 

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show inventory fex

To display the physical inventory of a Fabric Extender, such as the name, description, and volume ID, use the show inventory fex command.

show inventory fex chassis_ID

Syntax Description

chassis_ID

Fabric Extender chassis ID. The chassis ID range is from 100 to 199.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the physical inventory of a specific Fabric Extender chassis:

switch# show inventory fex 100 

NAME: "FEX 100 CHASSIS", DESCR: "N2K-C2248PQ-10GE  CHASSIS"

PID: N2K-C2248PQ-10GE  , VID: V00 , SN: FOC1616R00Q

NAME: "FEX 100 Module 1", DESCR: "Fabric Extender Module: 48x10GE, 16x10GE/4x40G

QSFP Supervisor"

PID: N2K-C2248PQ-10GE  , VID: V00 , SN: FOC16150CN1

NAME: "FEX 100 Fan 1", DESCR: "Fabric Extender Fan module"

PID: N2K-C2248PQ-FAN   , VID: N/A , SN: N/A

NAME: "FEX 100 Power Supply 1", DESCR: "Fabric Extender AC power supply"

PID: N2200-PAC-400W    , VID: V03 , SN: DTN1605P3EX

NAME: "FEX 100 Power Supply 2", DESCR: "Fabric Extender AC power supply"

PID: N2200-PAC-400W    , VID: V03 , SN: DTN1605P3EY

switch# 

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show locator-led

To display the status of the locator LED in a Fabric Extender, use the show locator-led command.

show locator-led status

Syntax Description

status

Displays the status of the locator LED in a Fabric Extender module.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Usage Guidelines

Use the locator-led command to toggle the locator LED of a Fabric Extender.

Examples

This example shows how to display the modules that have the locator LED set to off or on:

switch# show locator-led status 

Component        Locator LED Status

-----------------------------------

FEX 100          off

FEX 101          off

FEX 102          off

FEX 103          off

FEX 105          off

switch#

Related Commands

Command	Description
locator-led	Turns on the locator LED of a Fabric Extender chassis.
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show module fex

To display the module information for a Fabric Extender, use the show module fex command.

show module fex [all | chassis_ID]

Syntax Description

chassis_ID	Fabric Extender chassis ID. The chassis ID range is from 100 to 199.
all	Displays information about all Fabric Extender modules.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the module information of Fabric Extenders:

switch# show module fex all 

FEX Mod Ports Card Type                          Model              Status

--- --- ----- ---------------------------------- ------------------ -----------

100 1   48    Fabric Extender 48x1GE + 4x10G Module   N2K-C2248TP-1GE    present

101 1   48    Fabric Extender 48x1GE + 4x10G Module   N2K-C2248TP-1GE    present

102 1   32    Fabric Extender 32x10GE + 8x10G Module  N2K-C2232P-10GE    present

FEX Mod Sw              Hw      World-Wide-Name(s) (WWN)

--- --- --------------  ------  -----------------------------------------------

100 1   6.0(2u)N1(1u)   4.3     --

101 1   6.0(2u)N1(1u)   4.3     --

102 1   6.0(2u)N1(1u)   1.0     --

FEX Mod  MAC-Address(es)                         Serial-Num

--- ---  --------------------------------------  ----------

100 1    2c36.f836.0340 to 2c36.f836.036f        SSI15510MCP

101 1    a456.30c2.7900 to a456.30c2.792f        SSI16020453

102 1    000d.ecca.7c00 to 000d.ecca.7c1f        SSI133106K6

switch#

This commands shows how to display the module information for a specific Fabric Extender:

switch# show module fex 100 

FEX Mod Ports Card Type                          Model              Status

--- --- ----- ---------------------------------- ------------------ -----------

100 1   48    Fabric Extender 48x1GE + 4x10G Module   N2K-C2248TP-1GE    present

FEX Mod Sw              Hw      World-Wide-Name(s) (WWN)

--- --- --------------  ------  -----------------------------------------------

100 1   6.0(2)N1(1)   4.3     --

FEX Mod  MAC-Address(es)                         Serial-Num

--- ---  --------------------------------------  ----------

100 1    2c36.f836.0340 to 2c36.f836.036f        SSI15510MCP

switch# 

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show provision

To display information about provision, use the show provision command.

show provision failed-config slot-number

Syntax Description

failed-config	Displays the configuration that failed to be applied to the slot.
slot-number	Slot number in the chassis. The range is from 2 to 199.

Command Default

None

Command Modes

EXEC mode
Configuration synchronization mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the preprovisioning configuration that failed to be applied to slot 2:

switch# show provision failed-config 2

Config has not been applied yet for this slot.

switch#

Related Commands

Command	Description
provision	Preprovisions a module in a slot.
show running-config exclude-provision	Displays the running configuration excluding the preprovisioned features.
slot	Enables a slot for preprovisioning a module.

show queuing interface

To display the queuing information of interfaces, use the show queuing interface command.

show queuing interface [ethernet slot-chassis-no/port-slot-no/port-no]

Syntax Description

ethernet	(Optional) Specifies that queuing information be displayed for an Ethernet interface or a Fabric Extender.
slot-chassis-no	Slot number of the Ethernet interface or chassis ID of the Fabric Extender. The range is from 1 to 255.
port-slot-no	Port number of the Ethernet interface or the remote slot ID of the Fabric Extender. The range is from 1 to 128.
port-no	Port number of the Fabric Extender. The range is from 1 to 48.

Command Default

Displays the queuing information for all interfaces.

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the queuing information, including the buffer threshold and queue limit values, of a specified interface:

switch# show queuing interface ethernet 1/4 

Interface Ethernet1/4 TX Queuing

qos-group  sched-type  oper-bandwidth

    0       WRR             50

    1       WRR             50

    5       priority         0

Interface Ethernet1/4 RX Queuing

qos-group  0: 

    q-size: 102400, MTU: 1538

    drop-type: drop, xon: 0, xoff: 640

    Statistics:

        Pkts received over the port             : 1

        Ucast pkts sent to the cross-bar        : 0

        Mcast pkts sent to the cross-bar        : 1

        Ucast pkts received from the cross-bar  : 1577841

        Pkts sent to the port                   : 1577841

        Pkts discarded on ingress               : 0

        Per-priority-pause status               : Rx (Inactive), Tx (Inactive)

qos-group  1: 

    q-size: 76800, MTU: 2240

    drop-type: no-drop, xon: 128, xoff: 240

    Statistics:

        Pkts received over the port             : 0

        Ucast pkts sent to the cross-bar        : 0

        Mcast pkts sent to the cross-bar        : 0

        Ucast pkts received from the cross-bar  : 0

        Pkts sent to the port                   : 0

        Pkts discarded on ingress               : 0

        Per-priority-pause status               : Rx (Inactive), Tx (Inactive)

qos-group  5: 

    q-size: 122880, MTU: 1538

    drop-type: drop, xon: 0, xoff: 768

    Statistics:

        Pkts received over the port             : 0

        Ucast pkts sent to the cross-bar        : 0

        Mcast pkts sent to the cross-bar        : 0

        Ucast pkts received from the cross-bar  : 0

        Pkts sent to the port                   : 1

        Pkts discarded on ingress               : 0

        Per-priority-pause status               : Rx (Inactive), Tx (Inactive)

switch#

Table 1 describes the significant fields shown in the display.

Table 1 show queuing interface Field Descriptions 

Field	Description
Ethernet ...	Ethernet interface information.
qoS-group	Information about QoS groups configured on the switch.
sched-type	Type of schedule.
WRR	Weighted round robin(WRR). Queue eight for scheduling.
Priority	Priority of the queue.
q-size	Queue size.
drop-type	Queue drop type can be either drop or no-drop.
MTU	Maximum transmit unit (MTU) for the queue.
Xon	Transmission on at this threshold.
Xoff	Transmission off at this threshold.
Buffer threshold	Buffer threshold value for the interface.
Queue limit	Queue limit value for the interface.

Related Commands

Command	Description
hardware buffer-threshold	Configures the hardware buffer threshold.
hardware queue-limit	Configures the hardware queue limit.
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show running-config exclude-provision

To display the running configuration without the configuration for offline preprovisioned interfaces, use the show running-config exclude-provision command.

show running-config exclude-provision

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the running configuration without the offline preprovisioned interfaces:

switch# show running-config exclude-provision

!Command: show running-config exclude-provision

!Time: Mon Sep  6 08:10:16 2010

version 5.0(2)N1(1)

feature fcoe

feature telnet

feature tacacs+

cfs ipv4 distribute

cfs eth distribute

feature udld

feature interface-vlan

feature lacp

feature vpc

feature lldp

feature vtp

feature fex

username admin password 5 $1$wmFN7Wly$/pjqx1DfAkCCAg/KyxbUz/  role network-admin

username install password 5 !  role network-admin

username praveena password 5 !  role network-operator

no password strength-check

ip domain-lookup

ip domain-lookup

tacacs-server host 192.168.131.54 key 7 "wawy1234"

tacacs-server host 192.168.131.37

tacacs-server host 192.168.131.37 test username user1

aaa group server tacacs+ t1

    server 192.168.131.54

aaa group server tacacs+ tacacs

radius-server host 192.168.128.5 key 7 "KkwyCet" authentication accounting

aaa group server radius r1

    server 192.168.128.5

hostname BEND-2

vlan dot1Q tag native

logging event link-status default

logging event trunk-status default

no service recover-errdisable

errdisable recovery interval 600

no errdisable detect cause link-flap

errdisable recovery cause link-flap

errdisable recovery cause udld

--More--

<--output truncated-->

switch# 

Related Commands

Command	Description
copy running-config startup-config	Copies the running configuration to the startup configuration.
provision	Preprovisions a module in a slot.
show provision	Displays the preprovisioned module information.
show startup-config exclude-provision	Displays the startup configuration without the preprovisioning information for offline interfaces.
slot	Configures a chassis slot for a predefined module.

show running-config fex

To display the running configuration for Fabric Extenders (FEXs), use the show running-config fex command.

show running-config fex [all]

Syntax Description

all	(Optional) Displays FEX information including default settings.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display information on the running FEX configuration, including the buffer threshold value and queue limit:

switch# show running-config fex 

!Command: show running-config fex

!Time: Mon Jan 14 23:54:12 2013

version 6.0(2)N1(1)

feature fex

fex 100

  pinning max-links 1

  description "FEX0100"

fex 101

  pinning max-links 1

  description "FEX0101"

fex 102

  pinning max-links 1

  description "FEX0102"

interface Ethernet1/2

  fex associate 100

interface Ethernet1/4

  fex associate 101

interface Ethernet1/25

  fex associate 102

interface Ethernet1/26

  fex associate 102

switch# 

Related Commands

Command	Description
hardware buffer-threshold	Configures the hardware buffer threshold.
hardware queue-limit	Configures the hardware queue limit.
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show sprom fex

To display information about the SPROM, use the show sprom fex command.

show sprom fex {all | chassis_ID {all | backplane | powersupply module_no}}

Syntax Description

chassis_ID	Fabric Extender chassis ID. The chassis ID range is from 100 to 199.
all	Displays all SPROM content for a specific Fabric Extender.
backplane	Displays the backplane SPROM content for a specific Fabric Extender.
powersupply	Displays the power supply SPROM content for a specific Fabric Extender.
module_no	Power supply module number for a specific Fabric Extender. The range is from 1 to 2.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display all SPROM content for a specific Fabric Extender:

switch# show sprom fex 100 all 

DISPLAY FEX 100 SUP sprom contents

Common block:

 Block Signature : 0xabab

 Block Version   : 3

 Block Length    : 160

 Block Checksum  : 0x18c9

 EEPROM Size     : 65535

 Block Count     : 3

 FRU Major Type  : 0x6003

 FRU Minor Type  : 0x0

 OEM String      : Cisco Systems, Inc.

 Product Number  : N5K-C5110T-BF-1GE

 Serial Number   : JAF1237ABSE

 Part Number     : 73-12009-02

 Part Revision   : 00

 Mfg Deviation   : 0

 H/W Version     : 0.0

 Mfg Bits        : 0

 Engineer Use    : 0

 snmpOID         : 9.12.3.1.9.72.5.0

 Power Consump   : -200

 RMA Code        : 0-0-0-0

 CLEI Code       : 00000000000

 VID             : V00

Supervisor Module specific block:

 Block Signature : 0x6002

 Block Version   : 2

 Block Length    : 103

 Block Checksum  : 0x2648

 Feature Bits    : 0x0

 HW Changes Bits : 0x2

Card Index      : 11011

 MAC Addresses   : 00-00-00-00-00-00

 Number of MACs  : 0

 Number of EPLD  : 0

 Port Type-Num   : 2-52

 Sensor #1       : 85,75

 Sensor #2       : 100,90

 Sensor #3       : 100,90

 Sensor #4       : 100,90

 Sensor #5       : 100,90

 Sensor #6       : 100,90

 Sensor #7       : 100,90

 Sensor #8       : 100,90

 Max Connector Power: 1000

 Cooling Requirement: 300

 Ambient Temperature: 40

DISPLAY FEX 100 backplane sprom contents:

Common block:

 Block Signature : 0xabab

 Block Version   : 3

 Block Length    : 160

 Block Checksum  : 0x195d

 EEPROM Size     : 65535

 Block Count     : 5

 FRU Major Type  : 0x6001

 FRU Minor Type  : 0x0

 OEM String      : Cisco Systems, Inc.

 Product Number  : N5K-C5110T-BF-1GE

Serial Number   : JAF1237ABSE

 Part Number     : 73-12009-02

 Part Revision   : 00

 Mfg Deviation   : 0

 H/W Version     : 0.0

 Mfg Bits        : 0

 Engineer Use    : 0

 snmpOID         : 9.12.3.1.3.719.0.0

 Power Consump   : -800

 RMA Code        : 0-0-0-0

 CLEI Code       : 00000000

 VID             : V01

Chassis specific block:

 Block Signature : 0x6001

 Block Version   : 3

 Block Length    : 39

 Block Checksum  : 0x28a

 Feature Bits    : 0x0

 HW Changes Bits : 0x2

 Stackmib OID    : 0

 MAC Addresses   : 00-0d-ec-b1-13-00

 Number of MACs  : 64

 OEM Enterprise  : 0

 OEM MIB Offset  : 0

 MAX Connector Power: 0

WWN software-module specific block:

 Block Signature : 0x6005

 Block Version   : 1

 Block Length    : 0

 Block Checksum  : 0x66

wwn usage bits:

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00 00 00 00 00 00 00

 00 00

License software-module specific block:

 Block Signature : 0x6006

 Block Version   : 1

 Block Length    : 16

 Block Checksum  : 0x77

lic usage bits:

 00 00 00 00 00 00 00 00

DISPLAY FEX 100 power-supply 1 sprom contents:

Common block:

 Block Signature : 0xabab

 Block Version   : 3

 Block Length    : 124

 Block Checksum  : 0x15fc

 EEPROM Size     : 124

 Block Count     : 1

 FRU Major Type  : 0xab01

 FRU Minor Type  : 0x1

 OEM String      : Cisco Systems, Inc.

 Product Number  : N5K-PAC-200W

 Serial Number   : PAC12473L17

 Part Number     : 341-0335-01

 Part Revision   : 01

 CLEI Code       : COUPADSBAA

 VID             : 00V0

 snmpOID         : 0.0.0.0.0.0.0.0

 H/W Version     : 0.1

 Current         : 1667

RMA Code        : 0-0-0-0

switch#

This command shows how to display the power supply SPROM contents for a specific Fabric Extender:

switch# show sprom fex 100 powersupply 1 

DISPLAY FEX 100 power-supply 1 sprom contents:

Common block:

 Block Signature : 0xabab

 Block Version   : 3

 Block Length    : 124

 Block Checksum  : 0x15fc

 EEPROM Size     : 124

 Block Count     : 1

 FRU Major Type  : 0xab01

 FRU Minor Type  : 0x1

 OEM String      : Cisco Systems, Inc.

 Product Number  : N5K-PAC-200W

 Serial Number   : PAC12473L17

 Part Number     : 341-0335-01

 Part Revision   : 01

 CLEI Code       : COUPADSBAA

 VID             : 00V0

 snmpOID         : 0.0.0.0.0.0.0.0

 H/W Version     : 0.1

 Current         : 1667

 RMA Code        : 0-0-0-0

switch#

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show startup-config exclude-provision

To display the startup configuration that excludes the configuration for offline preprovisioned interfaces, use the show startup-config exclude-provision command.

show startup-config exclude-provision

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the startup configuration without the offline preprovisioned interfaces:

switch# show startup-config exclude-provision

Related Commands

Command	Description
provision	Preprovisions a module in a slot.
show provision	Displays the preprovisioned module information.
show running-config exclude-provision	Displays the running configuration excluding the preprovisioned features.
slot	Configures a chassis slot for a predefined module.

show system reset-reason fex

To display the reason for the last reset of the Fabric Extender, use the show system reset-reason fex command.

show system reset-reason fex chassis_ID

Syntax Description

chassis_ID

Fabric Extender chassis ID. The chassis ID range is from 100 to 199.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the last reset reason for a specific Fabric Extender:

switch# show system reset-reason fex 100 

----- reset reason for FEX 100 ---

1) At 0 usecs after Unknown time

    Reset Reason: Unknown (0)

    Service (Additional Info):

    Image Version: 6.0(2)N1(1)

2) At 492646 usecs after Sun Jan 13 03:18:29 2013

    Reset Reason: Kernel Reboot (1)

    Service (Additional Info): Reload new image

    Image Version: 6.0(2)N1(1)

3) At 278870 usecs after Sun Jan 13 02:44:14 2013

    Reset Reason: Unknown (0)

    Service (Additional Info):

    Image Version: 6.0(2)N1(1)

4) At 603531 usecs after Fri Jan 11 05:27:57 2013

    Reset Reason: Reset due to upgrade (88)

    Service (Additional Info): Reset due to upgrade

    Image Version: 6.0(2)N1(1)

switch#

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.

show version fex

To display the software version information about a Fabric Extender, use the show version fex command.

show version fex chassis_ID

Syntax Description

chassis_ID

Fabric Extender chassis ID. The chassis ID range is from 100 to 199.

Command Default

None

Command Modes

EXEC mode

Command History

Release	Modification
5.0(2)N1(1)	This command was introduced.

Examples

This example shows how to display the software version of a Fabric Extender:

switch# show version fex 100 

Software

  Bootloader version:           0.2

  System boot mode:             primary

  System image version:         6.0(2)N1(1) [build 6.0(2)N1(1)]

Hardware

  Module:                       Fabric Extender 48x1GE + 4x10G Module

  CPU:                          Motorola, e300c4

  Serial number:                FOC16031XJQ

  Bootflash:                    locked

Kernel uptime is 0 day(s), 22 hour(s), 20 minutes(s), 32 second(s)

Last reset at Mon Jan 14 06:41:35 2013

  Reason: Reset due to upgrade

  Service: Reset due to upgrade

switch#

Related Commands

Command	Description
show fex	Displays all configured Fabric Extender chassis connected to the switch.