Table Of Contents

R Commands

reference-bandwidth (FabricPath)

reply mode out-of-band

root-priority (FabricPath)

R Commands

---

This chapter describes the Cisco NX-OS FabricPath commands that begin with R.

reference-bandwidth (FabricPath)

To change the reference bandwidth used for setting an interface, use the reference bandwidth command. To return to the default setting, use the no form of this command.

reference-bandwidth bandwidth {Mbps | Gbps}

no reference-bandwidth bandwidth {Mbps | Gbps}

Syntax Description

bandwidth	Specifies the bandwidth in Mbps and Gbps. The range is from 1 to 400000 in Mbps and from 1 to 400 in Gbps.
Mbps	Specifies the bandwidth in Mbps.
Gbps	Specifies the bandwidth in Gbps.

Command Default

The defaults are as follows:

•Gbps: 400

•Mbps: 400000

Command Modes

FabricPath IS-IS configuration mode

Command History

Release	Modification
5.2(1)N1(1)	This command was introduced.

Usage Guidelines

This command requires an Enhanced Layer 2 license.

Examples

This example shows how to change the reference bandwidth for a Gbps interface:

switch# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

switch(config)# fabricpath domain default

switch(config-fabricpath-isis)# topology 1

switch(config-fabricpath-isis-topo)# reference-bandwidth 500 Gbps

switch(config-fabricpath-isis-topo)#

Related Commands

Command	Description
show fabricpath isis	Displays FabricPath Layer 2 IS-IS.

reply mode out-of-band

To configure fabricpath OAM out-of-band service reply mode, use the reply mode out-of-band command in fabricpath OAM profile configuration mode. To remove the out-of-band service reply mode, use the no form of this command.

reply mode out-of-band {ipv4 | ipv6} ip-address port-number

no reply mode out-of-band

Syntax Description

ipv4	Specifies the IPv4 address.
ipv6	Specifies the IPv6 address.
ip-address	An IPv4 or IPv6 address.
port-number	Port number. The range is from 0 to 65,535.

Command Default

The out-of-band reply mode is not configured.

Command Modes

Fabricpath OAM profile (config-fp-oam-profile)

Command History

Release	Modification
7.0(0)N1(1)	This command was introduced.

Usage Guidelines

Use the reply mode out-of-band command to configure reply mode information.

Examples

This example shows how to enter reply mode information:

switch(#) configure terminal

switch(config)# fabricpath oam profile 100

switch(config-fp-oam-profile)# reply mode out-of-band 10.1.1.7 500

Related Commands

Command	Description

root-priority (FabricPath)

To set the priority for which node becomes the root, use the root-priority command. To return to the default setting, use the no form of this command.

root-priority value

no root-priority value

Syntax Description

value

Root priority value per topology. The range is from 1 to 255. The default is 64.

Command Default

The default value is 64.

Command Modes

FabricPath IS-IS configuration mode

Command History

Release	Modification
5.2(1)N1(1)	This command was introduced.

Usage Guidelines

The highest numerical value for the priority is likely to become root.

This command requires an Enhanced Layer 2 license.

Examples

This example shows how to set the priority for which node becomes the root:

switch# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

switch(config)# fabricpath domain default

switch(config-fabricpath-isis)# topology 1

switch(config-fabricpath-isis-topo)# root-priority 1

switch(config-fabricpath-isis-topo)#

Related Commands

Command	Description
show fabricpath isis	Displays FabricPath IS-IS information.