Table Of Contents

Cisco Nexus 5000 Series System Management Commands

clear logging nvram

clear logging onboard

clear logging session

logging console

logging level

logging logfile

logging module

logging monitor

logging server

logging timestamp

show logging console

show logging info

show logging last

show logging level

show logging logfile

show logging module

show logging monitor

show logging nvram

show logging onboard

show logging server

show logging session status

show logging status

show logging timestamp

System Message Logging Facilities

Cisco Nexus 5000 Series System Management Commands

---

This chapter describes the system management commands available on Cisco Nexus 5000 Series switches.

clear logging nvram

Use the clear logging nvram command to clear the NVRAM logs.

clear logging nvram

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to clear the NVRAM logs:

switch# clear logging nvram 

switch#

Related Commands

Command	Description
show logging nvram	Displays the NVRAM logs.

clear logging onboard

To clear the OBFL entries in the persistent log, use the clear logging onboard command.

clear logging onboard [environmental-history] [exception-log] [obfl-log] [stack-trace]

Syntax Description

environmental-history	(Optional) Clears the OBFL environmental history.
exception-log	(Optional) Clears the OBFL exception log entries.
obfl-log	(Optional) Clears the OBFL (boot-uptime/device-version/obfl-history).
stack-trace	(Optional) Clears the OBFL stack trace entries.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

The following example shows how to clear the OBFL environmental history entries:

switch# clear logging onboard environmental-history

switch# 

The following example shows how to clear the OBFL exception-log entries:

switch# clear logging onboard exception-log

switch# 

The following example shows how to clear the OBFL (boot-uptime/device-version/obfl-history) entries:

switch# clear logging onboard obfl-log

switch# 

The following example shows how to clear the OBFL stack trace entries:

switch# clear logging onboard stack-trace

switch# 

Related Commands

Command	Description
show logging onboard	Displays onboard failure logs.

clear logging session

Use the clear logging session command to clear the current logging session.

clear logging session

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to clear the current logging session:

switch# clear logging session 

switch#

Related Commands

Command	Description
show logging session	Displays logging session status.

logging console

Use the logging console command to enable logging messages to the console session.

To disable logging messages to the console session, use the no form of this command.

logging console [severity-level]

no logging console

Syntax Description

severity-level

(Optional) The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows: •0—emergency: System unusable •1—alert: Immediate action needed •2—critical: Critical condition—default level •3—error: Error condition •4—warning: Warning condition •5—notification: Normal but significant condition •6—informational: Informational message only •7—debugging: Appears during debugging only

Command Default

None.

Command Modes

Global configuration.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to enable logging messages with a severity level of 4 (warning) or higher to the console session:

switch# configure terminal 

switch(config)# logging console 4 

switch(config)#

Related Commands

Command	Description
show logging console	Displays the console logging configuration.

logging level

Use the logging level command to enable logging messages from the defined facility that have the specified severity level or higher.

To disable logging messages from the defined facility, use the no form of this command.

logging level facility severity-level

no logging level facility severity-level

Syntax Description

facility

Defines the appropriate facility. The facilities are listed in the "System Message Logging Facilities" section. To apply the same severity level to all facilities, use the all facility.

severity-level

The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows: •0—emergency: System unusable •1—alert: Immediate action needed •2—critical: Critical condition—default level •3—error: Error condition •4—warning: Warning condition •5—notification: Normal but significant condition •6—informational: Informational message only •7—debugging: Appears during debugging only

Command Default

None.

Command Modes

Global configuration.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to enable logging messages from the AAA facility that have a severity level of 2 or higher:

switch# configure terminal 

switch(config)# logging level aaa 2 

switch(config)#

Related Commands

Command	Description
show logging level	Displays the facility logging level configuration.

logging logfile

Use the logging logfile command to configure the name of the log file used to store system messages and the minimum severity level to log.

To disable logging to the log file, use the no form of this command.

logging logfile logfile-name severity-level [size bytes]

no logging logfile [logfile-name severity-level [size bytes]]]

Syntax Description

logfile-name	Configure the name of the log file to be used to store system messages.
severity-level	The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows: •0—emergency: System unusable •1—alert: Immediate action needed •2—critical: Critical condition—default level •3—error: Error condition •4—warning: Warning condition •5—notification: Normal but significant condition •6—informational: Informational message only •7—debugging: Appears during debugging only
size bytes	(Optional) Specifies a maximum file size. The default file size is 4194304 bytes and can be configured from 4096 to 4194304 bytes.

Command Default

None.

Command Modes

Global configuration.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to configure a log file called logfile to store system messages and set its severity level to 4:

switch# configure terminal 

switch(config)# logging logfile logfile 4 

switch(config)#

Related Commands

Command	Description
show logging logfile	Displays the log file.

logging module

Use the logging module command to enable module log messages. Set a specified severity level or use the default.

To disable module log messages, use the no form of this command.

logging module [severity-level]

no logging module

Syntax Description

severity-level

(Optional) The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows: •0—emergency: System unusable •1—alert: Immediate action needed •2—critical: Critical condition •3—error: Error condition •4—warning: Warning condition •5—notification: Normal but significant condition—default level •6—informational: Informational message only •7—debugging: Appears during debugging only

Command Default

None.

Command Modes

Global configuration.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to enable module log messages:

switch# configure terminal 

switch(config)# logging module 

switch(config)#

Related Commands

Command	Description
show logging module	Displays the module logging status.

logging monitor

Use the logging monitor command to enable the device to log messages to the monitor (terminal line). This configuration applies to Telnet and SSH sessions.

To disable monitor log messages, use the no form of this command.

logging monitor [severity-level]

no logging monitor

Syntax Description

severity-level

(Optional) The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows: •0—emergency: System unusable •1—alert: Immediate action needed •2—critical: Critical condition—default level •3—error: Error condition •4—warning: Warning condition •5—notification: Normal but significant condition •6—informational: Informational message only •7—debugging: Appears during debugging only

Command Default

None.

Command Modes

Global configuration.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to enable monitor log messages:

switch# configure terminal 

switch(config)# logging monitor 

switch(config)#

Related Commands

Command	Description
show logging monitor	Displays the status of monitor logging.

logging server

Use the logging server command to configure a remote syslog server at the specified host name or IPv4/IPv6 address.

To disable the remote syslog server, use the no form of this command.

logging server host [severity-level] [facility {auth | authpriv | cron | daemon | ftp | kernel | local0 | local1 | local2 | local3 | local4 | local5 | local6 | local7 | lpr | mail | news | syslog | user | uucp} ]

no logging server host

Syntax Description

host	Configure the host name or IPv4/IPv6 address of the Remote Syslog Server.
severity-level	(Optional) The number of the desired severity level at which messages should be logged. Messages at or numerically lower than the specified level are logged. Severity levels are as follows: •0—emergency: System unusable •1—alert: Immediate action needed •2—critical: Critical condition—default level •3—error: Error condition •4—warning: Warning condition •5—notification: Normal but significant condition •6—informational: Informational message only •7—debugging: Appears during debugging only
facility facility	(Optional) Define the appropriate outgoing facility. The facilities are listed in the System Message Logging Facilities section. The default outgoing facility is local7.

Command Default

The default outgoing facility is local7.

Command Modes

Global configuration

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to configure a remote syslog server at a specified IPv4 address, using the default outgoing facility:

switch# configure terminal 

switch(config)# logging server 172.28.254.253 

switch(config)#

This example shows how to configure a remote syslog server at a specified host name, with severity level 5 or higher:

switch# configure terminal 

switch(config)# logging server syslogA 5 

switch(config)#

Related Commands

Command	Description
show logging server	Displays the configured syslog servers.

logging timestamp

Use the logging timestamp command to set the logging timestamp units. By default, the units are seconds.

To reset the logging timestamp units to the default, use the no form of this command.

logging timestamp {microseconds | milliseconds | seconds}

no logging timestamp {microseconds | milliseconds | seconds}

Syntax Description

microseconds | milliseconds | seconds

Selects the units to use for logging timestamps. The default units are seconds.

Command Default

None.

Command Modes

Global configuration.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to set the logging timestamp units to microseconds:

switch# configure terminal 

switch(config)# logging timestamp microseconds 

switch(config)#

Related Commands

Command	Description
show logging timestamp	Displays the logging timestamp configuration.

show logging console

Use the show logging console command to display the console logging configuration.

show logging console

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the console logging configuration:

switch# show logging console 

switch#

Related Commands

Command	Description
logging console	Configures logging to the console.

show logging info

Use the show logging info command to display the logging configuration.

show logging info

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the logging configuration:

switch# show logging info 

switch#

show logging last

Use the show logging last command to display the last number of lines of the logfile.

show logging last number

Syntax Description

number

Enters the number of lines to display from 1 to 9999.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the last 42 lines of the log file:

switch# show logging last 42 

switch#

show logging level

Use the show logging level command to display the facility logging severity level configuration.

show logging level [facility]

Syntax Description

facility

(Optional) Defines the appropriate logging facility. The facilities are listed in the System Message Logging Facilities section.

Command Default

None.

Command Modes

Global configuration.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the port-channel logging severity level configuration:

switch# show logging level port-channel 

switch#

Related Commands

Command	Description
logging level	Configures the facility logging level.

show logging logfile

Use the show logging logfile command to display the messages in the log file that were timestamped within the span entered. If you do not enter an end time, the current time is used.

show logging logfile [start-time yyyy mmm dd hh:mm:ss] [end-time yyyy mmm dd hh:mm:ss]

Syntax Description

start-time	(Optional) Enter a start time in the format yyyy mmm dd hh:mm:ss. Use three characters for the month (mmm) field, digits for the year (yyyy) and day (dd) fields, and digits separated by colons for the time (hh:mm:ss) field.
end-time	(Optional) Enter an end time in the format yyyy mmm dd hh:mm:ss. Use three characters for the month (mmm) field, digits for the year (yyyy) and day (dd) fields, and digits separated by colons for the time (hh:mm:ss) field.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the messages in the log file that were timestamped within the span shown:

switch# show logging logfile start-time 2008 mar 11 12:10:00 

switch#

Related Commands

Command	Description
logging logfile	Configures logging to a log file.

show logging module

Use the show logging module command to display the module logging configuration.

show logging module

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the module logging configuration:

switch# show logging module 

switch#

Related Commands

Command	Description
logging module	Configures module logging.

show logging monitor

Use the show logging monitor command to display the monitor logging configuration.

show logging monitor

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the monitor logging configuration:

switch# show logging monitor 

switch#

Related Commands

Command	Description
logging monitor	Configures logging on the monitor.

show logging nvram

Use the show logging nvram command to display the messages in the NVRAM log.

show logging nvram [last number-lines]

Syntax Description

last number-lines

(Optional) Enters the number of lines to display. The specified number of lines is displayed. Specify from 1 to 100 lines.

Command Default

None.

Command Modes

Global configuration.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the last 20 messages in the NVRAM log:

switch# show logging nvram last 20 

switch#

show logging onboard

To display the onboard logging information based on the error type, use the show logging onboard command.

show logging onboard {boot-uptime | device-version | endtime | environmental-history | exception-log | kernel-trace | obfl-history | obfl-logs | stack-trace | starttime | status} [> file | | type]

Syntax Description

boot-uptime	Displays the OBFL boot and uptime information.
device-version	Displays the OBFL device version information.
endtime	Displays the OBFL logs until the specified end time.in the following format: mm/dd/yy-HH:MM:SS
environmental-history	Displays the OBFL environmental history.
exception-log	Displays the OBFL exception log.
kernel-trace	Displays the OBFL kernel trace information.
obfl-history	Displays the OBFL history information.
obfl-logs	Displays the OBFL technical support log information.
stack-trace	Displays the OBFL kernel stack trace information.
starttime	Displays the OBFL logs from the specified start time in the following format: mm/dd/yy-HH:MM:SS
status	Displays the OBFL status enable or disable.
> file	(Optional) Redirects the output to a file. See the "Usage Guidelines" section for additional information.
| type	(Optional) Filters the output. See the "Usage Guidelines" section for additional information.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

The date and time arguments for the starttime and endtime keywords are entered as the date month/day/year (mm/dd/yy), followed by a hyphen, and the time in 24-hour format in hours:minutes:seconds (HH:MM:SS). For example:

•starttime 03/17/08-15:01:57

•endtime 03/18/08-15:04:57

The valid values for file are as follows:

•bootflash:

•ftp:

•scp:

•sftp:

•tftp:

•volatile:

The valid values for type are as follows:

•begin [-i] [-x] [word]—Begin with the line that matches the text.

–-i—Ignores the case difference when comparing the strings.

–-x—Prints only the lines where the match is a whole line.

–word—Specifies for the expression.

•count [> file | | type]—Counts number of lines.

•egrep | grep print-match—Egrep or Grep. Egrep searches for lines of text that match more sophisticated regular expression syntax than grep. Grep searches for lines of text that match one or many regular expressions, and outputs only the matching lines.

–-A num—Prints the specifies number of lines of context after every matching line. Range: 1 to 999.

–-B num—Prints the specifies number of lines of context before every matching line. Range: 1 to 999.

–-c—Prints a total count of matching lines only.

–-i—Ignores the case difference when comparing the strings.

–-n—Prints each match preceded by its line number.

–-v—Prints only the lines that contain no matches for the word argument.

–-w—Prints only lines where the match is a complete word

–-x—Prints only the lines where the match is a whole line.

–word—Specifies for the expression.

•exclude [-i] [-x] [word]—Excludes the lines that match.

–-i—Ignores the case difference when comparing the strings.

–-x—Prints only the lines where the match is a whole line.

–word—Specifies for the expression.

•head [-n num]—Stream Editor. The optional -n num keyword and argument allows you to specify the number of lines to print. Range: 0 to 2147483647.

•include [-i] [-x] [word]—Include the lines that match

–-i—Ignores the case difference when comparing the strings.

–-x—Prints only the lines where the match is a whole line.

–word—Specifies for the expression.

•last [num]—Displays the last lines to print. The optional num specifies the number of lines to print. Range: 0 to 9999.

•less [-E | -d]—Quits at the end of the file.

–-E—(Optional) Quits at the end of the file.

–-d—(Optional) Specifies a dumb terminal.

•no-more—Turns-off pagination for command output.

•sed command—Stream Editor

•wc—Counts words, lines, and characters.

–-c—(Optional) Specifies the output character count.

–-l—(Optional) Specifies the output line count.

–-w—(Optional) Specifies the output word count.

–>—Redirects it to a file.

–|—Pipes command output to filter.

Use this command to view OBFL data from system hardware. The OBFL feature is enabled by default and records operating temperatures, hardware uptime, interrupts, and other important events and messages that can assist with diagnosing problems with hardware cards or modules installed in a Cisco router or switch. Data is logged to files stored in nonvolatile memory. When the onboard hardware is started up, a first record is made for each area monitored and becomes a base value for subsequent records.

The OBFL feature provides a circular updating scheme for collecting continuous records and archiving older (historical) records, ensuring accurate data about the system. Data is recorded in one of two formats: continuous information that displays a snapshot of measurements and samples in a continuous file, and summary information that provides details about the data being collected. The message "No historical data to display" is seen when historical data is not available.

Examples

This example shows how to display the OBFL boot and uptime information:

switch# show logging onboard boot-uptime

Sat May  3 10:45:49 2008:  Boot Record

-------------------------------------------------------------------------------

Boot Time..........:  Sat May  3 10:45:49 2008

Slot Number........:  1

Serial Number......:  FLC12080040

Bios Version.......:    v1.0.0(04/01/08)

Firmware Version...:  4.0(0)N1(1) [build 4.0(0)N1(1)]

Table 6-1 describes the significant fields shown in the display.

Table 6-1 show logging onboard boot-uptime Command Output

Field	Description
Boot Time	Time boot occurred.
Slot Number	Slot number
Serial Number	Serial number of the module.
Bios Version	Primary binary input and output system (BIOS) version.
Firmware Version	Firmware version.

This example shows how to display the OBFL logging device information:

switch# show logging onboard device-version

----------------------------

OBFL Data for

    Module:  1

----------------------------

Device Version Record

----------------------------------------------------------------------

Timestamp                  Device Name      Instance Hardware Software

                                                 Num  Version  Version

----------------------------------------------------------------------

Sat May  3 10:45:52 2008   ALTOS                   0        2        0

Sat May  3 10:45:52 2008   GATOS                   0        1        0

Sat May  3 10:45:52 2008   GATOS                   1        1        0

Sat May  3 10:45:52 2008   GATOS                   2        1        0

Sat May  3 10:45:52 2008   GATOS                   3        1        0

Sat May  3 10:45:52 2008   GATOS                   4        1        0

Sat May  3 10:45:52 2008   GATOS                   5        1        0

Sat May  3 10:45:52 2008   GATOS                   6        1        0

Sat May  3 10:45:52 2008   GATOS                   7        1        0

Sat May  3 10:45:52 2008   GATOS                   8        1        0

Sat May  3 10:45:52 2008   GATOS                   9        1        0

Sat May  3 10:45:52 2008   GATOS                  10        1        0

Sat May  3 10:45:52 2008   GATOS                  11        1        0

Sat May  3 10:45:52 2008   GATOS                  12        1        0

Sat May  3 10:45:52 2008   GATOS                  13        1        0

Table 6-2 describes the significant fields shown in the display.

Table 6-2 show logging onboard device-version Command Output

Field	Description
Timestamp	Day, date, and time.
Device Name	Device name.
Instance Num	Number of instances.
Hardware Version	Hardware device version.
Software Version	Software device version.

This example shows how to display the OBFL history information:

switch# show logging onboard obfl-history 

----------------------------

OBFL Data for

    Module:  1

----------------------------

OBFL history records:

---------------------

Mon May 12 03:45:57 2008        : OBFL all logs cleared

Mon May 12 03:56:09 2008        : OBFL environmental-history logging enabled

Mon May 12 03:56:37 2008        : OBFL obfl-log logging to disabled

Mon May 12 03:57:12 2008        : OBFL obfl-log logging enabled

The show logging onboard obfl-history command displays the following information:

•Timestamp when OBFL is manually disabled.

•Timestamp when OBFL is manually enabled.

•Timestamp when OBFL data is manually cleared.

This example shows how to display the OBFL kernel stack trace information:

switch# show logging onboard module 2 stack-trace

==================== STACK TRACE ====================

Logging time: Sat Feb 29 19:47:38 2008

watchdog timeout: process swapper (0), jiffies 0x169bb

Stack: c0006e98 c001721c d195f5b4 c0005424 c0005500 c0003e90 c0005a2c c0005a40

c0001a88 c01bf610 c0000394

Call Trace:

print_stack2_buf + 0x50

kernel_thread + 0xb94

klm_cctrl + 0x4554

ppc_irq_dispatch_handler + 0x190

do_IRQ + 0x3c

ret_from_intercept + 0x0

probe_irq_mask + 0x494

probe_irq_mask + 0x4a8

transfer_to_handler + 0x15c

softnet_data + 0x2b0

Registers:

NIP: C0005A20 XER: 00000000 LR: C0005A2C SP: C01AA120 REGS: c01aa070 TRAP: 0500

Tainted: PF

MSR: 00009000 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 00

DEAR: C0029B40, ESR: C01F0000

MCSRR0: 00000000, MCSRR1: 00000000, MCAR: 00000000

MCSR: 00000000 MCAR: 00000000 MCPSUMR: 00000000

TASK = c01a8190[0] 'swapper' Last syscall: 120

last math 00000000 last altivec 00000000 last spe 00000000

GPR00: 00000000 C01AA120 C01A8190 00000000 00000032 C8F1DE28 D1010A9F 00000000

GPR08: 0000180F C01FA39C D1010AA3 C01B8D18 24044244 1003A44C 0FFF6700 10049000

GPR16: 0FFAE1B0 0FFFAC90 00000000 00000000 00000000 00000000 00000000 00000001

GPR24: 00000000 00000000 00001160 007FFEAB 007FFE00 C01F0000 C01F0000 00000000

The show logging onboard stack-trace command displays the following information:

•Time in seconds

•Time in microseconds

•Error description string

•Current process name and identification

•Kernel jiffies

•Stack trace

Related Commands

clear logging onboard	Clears the OBFL entries in the persistent log.
hw-module logging onboard	Enables or disabled OBFL entries based on the error type.

show logging server

Use the show logging server command to display the syslog server configuration.

show logging server

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the syslog server configuration:

switch# show logging server 

switch#

Related Commands

Command	Description
logging server	Configures a remote syslog server.

show logging session status

Use the show logging session status command to display the logging session status.

show logging session status

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the logging session status:

switch# show logging session status 

switch#

show logging status

Use the show logging status command to display the logging status.

show logging status

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the logging status:

switch# show logging status 

switch#

show logging timestamp

Use the show logging timestamp command to display the logging timestamp configuration.

show logging timestamp

Syntax Description

This command has no arguments or keywords.

Command Default

None.

Command Modes

Any.

Command History

Release	Modification
4.0(0)N1(1a)	This command was introduced.

Usage Guidelines

None.

Examples

This example shows how to display the logging timestamp configuration:

switch# show logging timestamp 

switch#

Related Commands

Command	Description
logging timestamp	Configures the logging timestamp granularity.

System Message Logging Facilities

Table 6-3 lists the facilities that you can use in system message logging configuration.

Table 6-3 System Message Logging Facilities 

Facility	Description
aaa	Sets level for aaa syslog messages.
aclmgr	Sets level for aclmgr syslog messages.
adjmgr	Sets syslog filter level for Adjacency Manager.
afm	Sets level for afm syslog messages.
all	Sets level for all facilities.
altos	Altos syslog level.
arp	Sets syslog filter level for ARP.
auth	Sets level for Authorization System.
authpriv	Sets level for Authorization (Private) system.
bootvar	Sets level for bootvar.
callhome	Callhome syslog level.
capability	Sets syslog level for mig utils daemon.
cdp	Sets logging level for CDP.
cert-enroll	Cert-enroll syslog level.
cfs	Sets logging level for CFS.
clis	Sets syslog filter level for CLIS.
core	core daemon syslog level.
cron	Sets level for Cron/at facility.
daemon	Sets level for System daemons.
dcbx	Sets level for dcx syslog messages.
device-alias	Sets syslog level for Device Alias Distribution Service.
dstats	delta statistics syslog level.
epp	Sets level for EPP syslog messages.
ethpc	Sets level for ethpc syslog messages.
ethpm	Sets level for ethpm syslog messages.
evmc	Sets level for evmc syslog messages.
fabric_start_cfg_mgr	fabric start cfg mgr syslog level.
fc2d	Sets level for fc2d syslog messages.
fcdomain	set level for fcdomain syslog messages.
fcns	Sets syslog filter level for name server.
fcpc	Sets level for fcpc syslog messages.
fcs	Sets syslog filter level for FCS.
fdmi	Sets logging level for fdmi.
feature-mgr	Feature manager syslog level.
flogi	Configure level for flogi syslog messages.
fs-daemon	fs daemon syslog level.
fspf	FSPF syslog level.
ftp	Sets level for File Transfer System.
fwm	Sets level for fwm syslog messages.
gatos	Gatos syslog level.
im	Sets level for im syslog messages.
kernel	Sets level for kernel.
l3vm	Sets syslog filter level for L3VM.
license	Licensing syslog level.
local0	Sets level for Local use daemons.
local1	Sets level for Local use daemons.
local2	Sets level for Local use daemons.
local3	Sets level for Local use daemons.
local4	Sets level for Local use daemons.
local5	Sets level for Local use daemons.
local6	Sets level for Local use daemons.
local7	Sets level for Local use daemons.
lpr	Sets level for Line Printer System.
mail	Sets level for Mail system.
monitor	Sets level for ethernet span syslog messages.
news	Sets level for USENET news.
nohms	Sets level for nohms syslog messages.
nqosm	Sets level for nqosm syslog messages.
ntp	Sets syslog filter level for NTP.
pfm	Sets level for pfm syslog messages.
pktmgr	Sets syslog filter level for Packet Manager.
plugin	Sets level for plugin syslog messages.
port	Sets level for port syslog messages.
port-channel	Sets level for port-channel syslog messages.
qd	Sets level for qd syslog messages.
radius	RADIUS syslog level.
rdl	Sets logging level for RDL.
res_mgr	Set slevel for res_mgr syslog messages.
rib	Sets level for rib.
rlir	Sets level for RLIR.
rscn	sets level for RSCN.
san-port-channel	Sets level for san-port-channel syslog messages.
scsi-target	scsi target daemon syslog level.
security	Security syslog level.
session	Sets level for session-manager syslog messages.
sifmgr	Sets level for sifmgr syslog messages.
spanning-tree	Sets level for stp syslog messages.
stp	Sets level for stp syslog messages.
syslog	Sets level for Internal Syslog Messages.
sysmgr	System Manager syslog level.
tcpudp	Sets syslog filter level for TCPUDP.
track	Sets level for track syslog messages.
urib	Sets syslog filter level for URIB.
user	Sets level for User Process.
uucp	Sets level for Unix-to-Unix copy system.
vlan_mgr	Sets level for VLAN syslog messages.
vmm	Sets level for vmm syslog messages.
vsan	VSAN syslog level.
vshd	Sets logging level for vshd.
wwnm	Sets WWN Manager syslog level.
xml	XML agent syslog level.
zone	Sets syslog filter level for zone server.
zschk	Sets level for zschk syslog messages.