 Feedback
|
Contents
- Release Notes for Cisco ASR 9000 Series Aggregation Services Routers for Cisco IOS XR Software Release 4.3.2
- System Requirements
- Feature Set Table
- Memory Requirements
- RSP Memory Upgrade
- Upgrading from A9K-RSP440-TR to A9K-RSP440-SE RSP
- Upgrading from A9K-RSP-4G RSP to A9K-RSP-8G RSP
- RSP Memory Downgrade
- Downgrading from A9K-RSP440-SE to A9K-RSP440-TR
- Downgrading from A9K-RSP-8G to A9K-RSP-4G
- Supported Hardware
- Software Compatibility
- Cisco ASR 9000 Series Aggregration Services Router Right-To-Use (RTU) Licensing
- Firmware Support
- Determining Your Software Version
- Software Features Introduced in Cisco IOS XR Software Release 4.3.2 for Cisco ASR 9000 Series Aggregation Service Router
- extcommunity-set
- Provider Backbone Bridging Ethernet VPN
- TCP MSS Adjustment
- Many-to-One Address Mapping in NAT on ISM
- Differentiated Services Code Point (DSCP) Marking support for TACACS packets
- Implementing Lawful Intercept
- Hardware Features Introduced in Cisco IOS XR Software Release 4.3.2 for the Cisco ASR 9000 Series Router
- Important Notes
- Caveats
- Cisco IOS XR Caveats
- Caveats Specific to the Cisco ASR 9000 Series Aggregation Services Router
- Caveats Specific to the ASR 9001 Router
- Upgrading Cisco IOS XR Software
- Troubleshooting
- Resolving Upgrade File Issues
- Obtaining Documentation and Submitting a Service Request
Release Notes for Cisco ASR 9000 Series Aggregation Services Routers for Cisco IOS XR Software Release 4.3.2
NCS 6000 Series Router Key Features [Infographic]
Cisco IOS XR Software is a distributed operating system designed for continuous system operation combined with service flexibility and higher performance.
Note
For information on Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release 4.3.2, see the Features Supported on the Cisco ASR 9000 Series Aggregation Services Router section.
These release notes describe the features provided on the Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release 4.3.2 and are updated as needed.
For a list of software caveats that apply to the Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release 4.3.2, see the Caveats section. The caveats are updated for every release and are described at http://www.cisco.com.
Cisco IOS XR Software running on the Cisco ASR 9000 Series Router provides the following features and benefits:
- IP and Routing—This supports a wide range of IPv4 and IPv6 services and routing protocols such as Border Gateway Protocol (BGP), Routing Information Protocol (RIPv2), Intermediate System-to-Intermediate System (IS-IS), Open Shortest Path First (OSPF), IP Multicast, Routing Policy Language (RPL), Hot Standby Router Protocol (HSRP), and Virtual Router Redundancy Protocol (VRRP) features.
- Ethernet Services—The following Ethernet features are supported:
- Ethernet Virtual Connections (EVCs)
- Flexible VLAN classification
- Flexible VLAN translation
- IEEE bridging
- IEEE 802.1s Multiple Spanning Tree (MST)
- MST Access Gateway
- L2VPN
- Virtual Private LAN Services (VPLS), Hierarchical VPLS (H-VPLS), Virtual Private Wire Service (VPWS), Ethernet over MPLS (EoMPLS), pseudo wire redundancy, and multi segment pseudo wire stitching.
- BGP Prefix Independent Convergence—This provides the ability to converge BGP routes within sub seconds instead of multiple seconds. The Forwarding Information Base (FIB) is updated, independent of a prefix, to converge multiple 100K BGP routes with the occurrence of a single failure. This convergence is applicable to both core and edge failures and with or without MPLS. This fast convergence innovation is unique to Cisco IOS XR Software.
- Multiprotocol Label Switching (MPLS)—This supports MPLS protocols, including Traffic Engineering (TE) [including TE-FRR and TW Preferred Path], Resource Reservation Protocol (RSVP), Label Distribution Protocol (LDP), Targeted LDP (T-LDP), Differentiated Services (DiffServ)-aware traffic engineering, and Layer 3 Virtual Private Network (L3VPN).
- Multicast—This provides comprehensive IP Multicast software including Source Specific Multicast (SSM) and Protocol Independent Multicast (PIM) in Sparse Mode only. The Cisco ASR 9000 Series Aggregation Services Router also supports Auto-Rendezvous Point (AutoRP), Multiprotocol BGP (MBGP), Multicast Source Discovery Protocol (MSDP), Internet Group Management Protocol Versions 2 and 3 (IGMPv2 and v3), and IGMPv2 and v3 snooping.
- Quality of Service (QOS)—This supports QoS mechanisms including policing, marking, queuing, random and hard traffic dropping, and shaping. Additionally, Cisco IOS XR supports modular QoS command-line interface (MQC). MQC is used to configure various QoS features on various Cisco platforms, including the Cisco ASR 9000 Series Aggregation Services Router. Supports the following:
- Manageability—This provides industry-standard management interfaces including modular command-line interface (CLI), Simple Network Management Protocol (SNMP), and native Extensible Markup Language (XML) interfaces. Includes a comprehensive set of Syslog messages.
- Security—This provides comprehensive network security features including Layer 2 and Layer 3 access control lists (ACLs); routing authentications; Authentication, Authorization, and Accounting (AAA)/Terminal Access Controller Access Control System (TACACS+), Secure Shell (SSH), Management Plane Protection (MPP) for management plane security, and Simple Network Management Protocol version3 (SNMPv3). Control plane protections integrated into line card Application-Specific Integrated Circuits (ASICs) include Generalized TTL Security Mechanism (GTSM), RFC 3682, and Dynamic Control Plane Protection (DCPP).
- Availability—This supports rich availability features such as fault containment, fault tolerance, fast switchover, link aggregation, nonstop routing for ISIS, LDP and OSPF, and nonstop forwarding (NSF).
- Enhanced core competencies:
- System Requirements
- Determining Your Software Version
- Software Features Introduced in Cisco IOS XR Software Release 4.3.2 for Cisco ASR 9000 Series Aggregation Service Router
- Hardware Features Introduced in Cisco IOS XR Software Release 4.3.2 for the Cisco ASR 9000 Series Router
- Important Notes
- Caveats
- Upgrading Cisco IOS XR Software
- Troubleshooting
- Obtaining Documentation and Submitting a Service Request
System Requirements
This section describes the system requirements for Cisco ASR 9000 Series Aggregation Services Router Software Release .
To determine the software versions or levels of your current system, see the Determining Your Software Version section.
- Feature Set Table
- Memory Requirements
- Supported Hardware
- Software Compatibility
- Cisco ASR 9000 Series Aggregration Services Router Right-To-Use (RTU) Licensing
- Firmware Support
Feature Set Table
The Cisco ASR 9000 Series Aggregation Services Router Software is packaged in feature sets (also called software images). Each feature set contains a specific set of Cisco ASR 9000 Series Aggregation Services Router Software Release 4.3.2
Table 1 lists the Cisco ASR 9000 Series Aggregation Services Router Software feature set matrix (PX PIE files) and associated filenames available for the Release 4.3.2 supported on the Cisco ASR 9000 Series Aggregation Services Router.
Table 1 Cisco IOS XR Software Release 4.3.2 PX PIE Files Feature Set
Filename
Description
Composite Package
Cisco IOS XR IP Unicast Routing Core Bundle
asr9k-mini-px.pie-4.3.2
Contains the required core packages, including OS, Admin, Base, Forwarding, Modular Services Card, Routing, SNMP Agent, and Alarm Correlation.
Cisco IOS XR IP Unicast Routing Core Bundle
asr9k-mini-px.vm-4.3.2
Contains the required core packages including OS, Admin, Base, Forwarding, Forwarding Processor Card 40G, Routing, SNMP Agent, Diagnostic Utilities, and Alarm Correlation.
Optional Individual Packages (Packages are installed individually)
Cisco IOS XR Manageability Package
asr9k-mgbl-px.pie-4.3.2
CORBA2 agent, XML3 Parser, and HTTP server packages. This PIE also contains some SNMP MIB infrastructure. Certain MIBs won't work if this PIE is not installed.
Cisco IOS XR MPLS Package
asr9k-mpls-px.pie-4.3.2
MPLS Traffic Engineering (MPLS-TE), Label Distribution Protocol (LDP), MPLS Forwarding, MPLS Operations, Administration, and Maintenance (OAM), Link Manager Protocol (LMP), Optical User Network Interface (OUNI), Resource Reservation Protocol (RSVP), and Layer-3 VPN.
Cisco IOS XR Multicast Package
asr9k-mcast-px.pie-4.3.2
Multicast Routing Protocols (PIM, Multicast Source Discovery Protocol [MSDP], Internet Group Management Protocol [IGMP], Auto-RP), Tools (SAP, MTrace), and Infrastructure [(Multicast Routing Information Base [MRIB], Multicast-Unicast RIB [MURIB], Multicast forwarding [MFWD]), and Bidirectional Protocol Independent Multicast (BIDIR-PIM).
Cisco IOS XR Security Package
asr9k-k9sec-px.pie-4.3.2
Support for Encryption, Decryption, IP Security (IPSec), Secure Shell (SSH), Secure Socket Layer (SSL), and Public-key infrastructure (PKI) (Software based IPSec support—maximum of 500 tunnels)
Cisco IOS XR Advanced Video Package
asr9k-video-px.pie-4.3.2
Firmware for the advanced video feature for Cisco ASR 9000 Series Router chassis.
Cisco IOS XR Optics Package
asr9k-optic-px.pie-4.3.2
Firmware for the optics feature for Cisco ASR 9000 Series Aggregation Services Router Chassis. It enables Transport / OTN feature under interfaces.
Cisco IOS XR FPD Package
asr9k-fpd-px.pie-4.3.2
Firmware pie for all LC and RSP FPGA's and ASIC's.
Cisco IOS XR Documentation Package
asr9k-doc-px.pie-4.3.2
.man pages for Cisco IOS XR Software on the Cisco ASR 9000 Series Aggregation Services Router Chassis.
Cisco IOS XR Services Package
asr9k-services-px.pie-4.3.2
Includes binaries to support CGv6 on ISM.
Cisco IOS XR Satellite Package
asr9000v-nV-px.pie-4.3.2
Includes Satellite software images.
Cisco IOS XR BNG Package
asr9k-bng-px.pie-4.3.2
Includes binaries to support BNG features.
Cisco IOS XR Lawful Intercept (LI) Package
asr9k-li-px.pie-4.3.2
Includes LI software images.
Cisco IOS XR Cisco ASR 903 Series Router Package
asr9k-asr903-nV-px.pie-4.3.2
Includes binaries to support Cisco ASR 903 Series Router software.
Cisco IOS XR Cisco ASR 901 Series Router Package
asr9k-asr901-nV-px.pie-4.3.2
Includes binaries to support Cisco ASR 901 Series Router software.
CautionA P image should be loaded only on RSP-2. PX PIE image files should be loaded only on RSP-440 and ASR-9922-RP.
Table 2 lists the Cisco ASR 9000 Series Aggregation Services Router TAR files.Memory Requirements
Caution
If you remove the media in which the software image or configuration is stored, the router may become unstable and fail.
The minimum memory requirements for Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release 4.3.2 consist of the following:
- minimum 6-GB memory on the RSP-440 and ASR9922 RP [A9K-RSP-4G and A9K-RSP-8G is 4-GB]
- maximum 12-GB memory on the RSP-440 and ASR9922 RP [A9K-RSP-4G and A9K-RSP-8G is 4-GB]
- minimum 2-GB compact flash on route switch processors (RSPs)
- minimum 4-GB memory on the line cards (LCs)
These minimum memory requirements are met with the base board design.
The supported ASR9K low memory and high memory RSP card PIDs are :
Description PID Release ASR 9922 Route Processor 6GB for Packet Transport
ASR-9922-RP-TR
ASR 9922 Route Processor 12GB for Service Edge
ASR-9922-RP-SE
ASR9001 Route Switch Processor 8GB
—
Release 4.2.1
ASR9K Route Switch Processor with 440G/slot Fabric and 6GB
A9K-RSP440-TR
Release 4.2.0
ASR9K Route Switch Processor with 440G/slot Fabric and 12GB
A9K-RSP440-SE
Release 4.2.0
ASR9K Fabric, Controller 4G memory
A9K-RSP-4G
Release 3.7.2
Route Switch Processor 8G Memory
A9K-RSP-8G
Release 3.7.2
ASR 9900 Route Processor 12GB for Service Edge
ASR-9900-RP-SE
Release 4.3.2
ASR 9900 Route Processor 6GB for Packet Transport
ASR-9900-RP-TR
Release 4.3.2
RSP Memory Upgrade
ProcedureThis section describes the process to upgrade the Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release from a small memory model ASR-9922-RP-TR RSP card to a large memory model ASR-9922-RP-SE RSP card.
The upgrade sequence is as follows:
Upgrading from A9K-RSP440-TR to A9K-RSP440-SE RSP
ProcedureThe process to upgrade the Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release from a small memory model A9K-RSP440-TR RSP card to a large memory model A9K-RSP440-SE RSP card is as follows:
Upgrading from A9K-RSP-4G RSP to A9K-RSP-8G RSP
ProcedureThe process to upgrade the Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release from a small memory model A9K-RSP-4G RSP card to a large memory model A9K-RSP-8G RSP card is as follows:
RSP Memory Downgrade
ProcedureThis section describes the process to downgrade the Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release from a large memory model ASR-9922-RP-SE RSP card to a small memory model ASR-9922-RP-TR RSP card.
CautionBefore attempting an RSP memory downgrade, measure the memory consumption of the current system configuration using the large memory model ASR-9922-RP-SE RSP card. You need to ensure that the Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release is still able to run the system configuration using the small memory model ASR-9922-RP-TR RSP card.
The RSP memory downgrade sequence is as follows:
Downgrading from A9K-RSP440-SE to A9K-RSP440-TR
ProcedureThe process to downgrade the Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release from a large memory model A9K-RSP440-SE RSP card to a small memory model A9K-RSP440-TR RSP card is as follows:
Downgrading from A9K-RSP-8G to A9K-RSP-4G
ProcedureThe process to downgrade the Cisco ASR 9000 Series Aggregation Services Router running Cisco IOS XR Software Release from a large memory model A9K-RSP-8G RSP card to a small memory model A9K-RSP-4G RSP card is as follows:
Supported Hardware
Cisco IOS XR Software Release supports Cisco ASR 9000 Series Aggregation Services Routers.
All hardware features are supported on Cisco IOS XR Software, subject to the memory requirements specified in the "Memory Requirements" section.
The following tables lists the supported hardware components on the Cisco ASR 9000 Series Router and the minimum required software versions. For more information, see the Firmware Support section.
Table 3 Cisco ASR 9000 Series Aggregation Services Router Supported Hardware and Minimum Software Requirements Component
Part Number
Support from Version
Cisco ASR 9000 Series Aggregation Services Router 22-Slot
Cisco ASR 9000 Series Aggregation Services Router 22-Slot 20 Line Card Slot AC Chassis w/ PEM V2
ASR-9922-AC
Cisco ASR 9000 Series Aggregation Services Router 22-Slot 20 Line Card Slot DC Chassis w/ PEM V2
ASR-9922-DC
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Accessory Kit with grounding locks, guide rails etc
ASR-9922-ACC-KIT
NA
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Accessory - Cover for Power Shelves and Modules
ASR-9922-PWR-COV
NA
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Air Reflector
ASR-9922-AIRREF
NA
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Accessory - Door (with lock) and Fan Tray Covers
ASR-9922-DOOR
NA
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Fan Tray
ASR-9922-FAN
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Air Filter with Media, Center
ASR-9922-FLTR-CEN
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Air Filter with Media, Left & Right
ASR-9922-FLTR-LR
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Route Processor Filler
ASR-9922-RP-FILR
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Route Processor 12GB for Service Edge
ASR-9922-RP-SE
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Route Processor 6GB for Packet Transport
ASR-9922-RP-TR
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Switch Fabric Card Slot Filler
ASR-9922-SFC-FILR
Cisco ASR 9000 Series Aggregation Services Router 22-Slot Switch Fabric Card/110G
ASR-9922-SFC110
Cisco ASR 9000 Series Aggregation Services Router 2-RU
Cisco ASR 9000 Series Aggregation Services Router 2-Slot Route Processor
—
Release 4.2.1
Cisco ASR 9000 Series Aggregation Services Router 2-Slot Fan Tray
ASR-9001-FAN
Release 4.2.1
Cisco ASR 9000 Series Aggregation Services Router 2-Slot Line Card
ASR-9001-LC
Release 4.2.1
Cisco ASR 9000 Series Aggregation Services Router
ASR-9001-TRAY
Release 4.2.1
Cisco ASR 9000 Series Aggregation Services Router 6-Slot
Cisco ASR 9000 Series Aggregation Services Router 6-Slot System
ASR-9006
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 6-Slot Fan Tray
ASR-9006-FAN
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 6-Slot Door Kit
ASR-9006-DOOR
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 6-Slot AC Chassis
ASR-9006-AC
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 6-Slot DC Chassis
ASR-9006-DC
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 6-Slot Air
Cisco ASR 9000 Series Aggregation Services Router 6-Slot Air Filter
ASR-9006-FILTER
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 10-Slot
Cisco ASR 9000 Series Aggregation Services Router 10-Slot System
ASR-9010
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 10-Slot Fan Tray
ASR-9010-FAN
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 10-Slot Door Kit
ASR-9010-DOOR
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 10-Slot AC Chassis
ASR-9010-AC
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 10-Slot DC Chassis
ASR-9010-DC
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 2 Post Mounting Kit
ASR-9010-2P-KIT
Release 3.7.2
Cisco ASR 9000 Series Aggregration Services Router 4 Post Mounting Kit
ASR-9010-2P-KIT
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 10-Slot Air
Cisco ASR 9000 Series Aggregation Services Router 10-Slot Air Filter
ASR-9010-FILTER
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 10-Slot External Exhaust Air Shaper
ASR-9010-AIRSHPR
NA
Cisco ASR 9000 Series Aggregation Services Router 10-Slot Air Inlet Grill
ASR-9010-GRL
NA
Cisco ASR 9000 Series Aggregation Services Router Power
Cisco ASR 9000 Series Aggregation Services Router 2KW DC Power Module, version 2
A9K-2KW-DC-V2
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 3KW AC Power Module, version 2
A9K-3KW-AC-V2
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router AC Power Entry Module Version 2
A9K-AC-PEM-V2
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router DC Power Entry Module Version 2
A9K-DC-PEM-V2
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router Power Entry Module Version 2 Filler
A9K-PEM-V2-FILR
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 1.5kW DC Power Module
A9K-1.5KW-DC
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 2kW DC Power Module
A9K-2KW-DC
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 3kW AC Power Module
A9K-3KW-AC
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router Line Cards
Cisco ASR 9000 Series Aggregation Services Router 1-port 100GE, Service Edge Optimized
A9K-1X100GE-SE
Cisco ASR 9000 Series Aggregation Services Router 1-port 100GE, Packet Transport Optimized
A9K-1X100GE-TR
Cisco ASR 9000 Series Aggregation Services Router 36-port 10GE, Service Edge Optimized
A9K-36X10GE-SE
Cisco ASR 9000 Series Aggregation Services Router 36-port 10GE, Packet Transport Optimized LC
A9K-36X10GE-TR
Cisco ASR 9000 Series Aggregation Services Router 2-Port Ten Gigabit Ethernet + Cisco ASR 9000 Series Aggregation Services Router 20-Port Gigabit Ethernet, Medium Queue
A9K-2T20GE-B
Release 3.9.0
Cisco ASR 9000 Series Aggregation Services Router 2-Port Ten Gigabit Ethernet + Cisco ASR 9000 Series Aggregation Services Router 20-Port Gigabit Ethernet, High Queue
A9K-2T20GE-E
Release 3.9.0
Cisco ASR 9000 Series Aggregation Services Router 4-Port Ten Gigabit Ethernet, Medium Queue
A9K-4T-B
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 4-Port Ten Gigabit Ethernet Extended Line Card, High Queue
A9K-4T-E
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 4-Port Ten Gigabit Ethernet, Low Queue
A9K-4T-L
Release 3.9.0
Cisco ASR 9000 Series Aggregation Services Router 8-Port Ten Gigabit Ethernet, 80G Line Rate Extended Line Card, Medium Queue
A9K-8T-B
Release 4.0.1
Cisco ASR 9000 Series Aggregation Services Router 8-Port Ten Gigabit Ethernet, 80G Line Rate Extended Line Card, High Queue
A9K-8T-E
Release 3.9.0
Cisco ASR 9000 Series Aggregation Services Router 8-Port Ten Gigabit Ethernet, 80G Line Rate Extended Line Card, Low Queue
A9K-8T-L
Release 3.9.0
Cisco ASR 9000 Series Aggregation Services Router 8-Port Ten Gigabit Ethernet, Medium Queue
A9K-8T/4-B
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 8-Port Ten GE DX Extended Line Card, High Queue
A9K-8T/4-E
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 8-Port Ten Gigabit Ethernet, Low Queue
A9K-8T/4-L
Release 3.9.0
Cisco ASR 9000 Series Aggregation Services Router 16-Port Ten Gigabit Ethernet, Medium Queue
A9K-4T-B
Release 4.0.1
Cisco ASR 9000 Series Aggregation Services Router 40-Port Ten Gigabit Ethernet, Medium Queue
A9K-40GE-B
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 40-Port Ten Gigabit Ethernet, High Queue
A9K-40GE-E
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router 40-Port Ten Gigabit Ethernet, Low Queue
A9K-40GE-L
Release 3.9.0
Cisco ASR 9000 Series Aggregation Services Router Line Card Filler
A9K-LC-FILR
Release 3.7.2
ISM (Integrated Service Module) Line Card
A9K-ISM-100
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 2-Port Hundred Gigabit Ethernet, Service Edge Optimized
A9K-2X100GE-SE
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 2-Port Hundred Gigabit Ethernet, Packet Transport Optimized
A9K-2X100GE-TR
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 24-Port Ten Gigabit Ethernet, Service Edge Optimized
A9K-24X10GE-SE
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 24-Port Ten Gigabit Ethernet, Packet Transport Optimized
A9K-24X10GE-TR
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router Modular Line Cards
Cisco ASR 9000 Series Aggregation Services Router 80 Gig Modular Line Card, Service Edge Optimized
A9K-MOD80-SE
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 80 Gig Modular Line Card, Packet Transport Optimized
A9K-MOD80-TR
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 160 Gig Modular Line Card, Service Edge Optimized
A9K-MOD160-SE
Release 4.2.1
Cisco ASR 9000 Series Aggregation Services Router 160 Gig Modular Line Card, Packet Transport Optimized
A9K-MOD160-TR
Release 4.2.1
Cisco ASR 9000 Series Aggregation Services Router Modular Port Adapters (MPAs)
Cisco ASR 9000 Series Aggregation Services Router 1-port 40GE Modular Port Adapter
A9K-MPA-1X40GE
Release 4.2.3
Cisco ASR 9000 Series Aggregation Services Router 4-port 10GE Modular Port Adapter
A9K-MPA-4X10GE
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 20-port 1GE Modular Port Adapter
A9K-MPA-20X1GE
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router 2-port 10GE Modular Port Adapter
A9K-MPA-2X10GE
Release 4.2.1
Cisco ASR 9000 Series Aggregation Services Router 2-port 40GE Modular Port Adapter
A9K-MPA-2X40GE
Release 4.2.1
Cisco ASR 9000 Series Aggregation Services Router Route Switch Processor Cards
Cisco ASR 9000 Series Aggregation Services Router Route Switch Processor, 4G Memory
A9K-RSP-4G
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router Route Switch Processor, 8G Memory
A9K-RSP-8G
Release 4.0.1
Cisco ASR 9000 Series Aggregation Services Router Route Switch Processor Filler
ASR-9000-RSP-FILR
Release 3.7.2
Cisco ASR 9000 Series Aggregation Services Router Next Generation Route Switch Processor, Service Edge Optimized
A9K-RSP-440-SE
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router Next Generation Route Switch Processor, Packet Transport Optimized
A9K-RSP-440-TR
Release 4.2.0
Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Cards
Cisco ASR 9000 SIP-700 SPA interface processor
A9K-SIP-700
Release 3.9.0
2-Port Channelized OC-12/DS0 SPA
SPA-2XCHOC12/DS0
Release 3.9.0
1-Port Channelized OC48/STM16 DS3 SPA
SPA-1XCHOC48/DS3
Release 4.0.1
2-Port OC-48/STM16 SPA
SPA-2XOC48POS/RPR
Release 4.0.1
8-Port OC12/STM4 SPA
SPA-8XOC12-POS
Release 4.0.1
1-Port OC-192/STM-64 POS/RPR SPA
SPA-OC192POS-XFP
Release 4.0.1
4-Port Clear Channel T3/E3 SPA
SPA-4XT3E3
Release 4.0.1
2-Port Clear Channel T3/E3 SPA
SPA-2XT3E3
Release 4.0.1
1-Port Channelized OC-3/STM-1 SPA
SPA-1XCHSTM1/OC3
Release 4.0.1
4-Port OC-3/STM-1 POS SPA
SPA-4XOC3
Release 4.0.1
8-Port OC-3/STM-1 POS SPA
SPA-8XOC3
Release 4.0.1
4-Port Channelized T3 to DS0 SPA
SPA-4XCT3/DS0
Release 4.1.0
8-Port Channelized T1/E1 SPA
SPA-8XCHT1/E1
Release 4.1.0
1-Port and 3-Port Clear Channel OC-3 ATM SPA
SPA-1/3XOC3ATM
Release 4.2.0
1-Port Clear Channel OC-12 ATM SPA
SPA-1XOC12ATM
Release 4.2.0
1-Port Channelized OC-3 ATM CEoP SPA
SPA-1XOC3-CE-ATM
Release 4.2.0
Software Compatibility
Cisco IOS XR Software Release is compatible with the following Cisco ASR 9000 Series Aggregation Services Router systems.
Table 4 Cisco ASR 9000 Series Aggregation Services Router Supported Software Licenses Software License
Part Number
Cisco ASR 9000 Series Aggregation Services Router iVRF License
A9K-IVRF-LIC
Cisco ASR 9000 Series Aggregation Services Router Per Chassis Advanced Video License
A9K-ADV-VIDEO-LIC
Cisco ASR 9000 Series Aggregation Services Router Per Line Card Advanced Optical License
A9K-ADV-OPTIC-LIC
Cisco ASR 9000 Series Aggregation Services Router L3VPN License, Medium Queue and Low Queue Line Cards
A9K-AIP-LIC-B
Cisco ASR 9000 Series Aggregation Services Router L3VPN License, High Queue Line Cards
A9K-AIP-LIC-E
Note that error messages may display if features run without the appropriate licenses installed. For example, when creating or configuring VRF, if the A9K-IVRF-LIC license is not installed before creating a VRF, the following message displays:
RP/0/RSP0/CPU0:router#LC/0/0/CPU0:Dec 15 17:57:53.653 : rsi_agent[247]: %LICENSE-ASR9K_LICENSE-2-INFRA_VRF_NEEDED : 5 VRF(s) are configured without license A9K-iVRF-LIC in violation of the Software Right To Use Agreement. This feature may be disabled by the system without the appropriate license. Contact Cisco to purchase the license immediately to avoid potential service interruption.For Cisco license support, please contact your Cisco Sales Representative or Customer Service at 800- 553-NETS (6387) or 408-526-4000. For questions on the program other than ordering, please send e-mail to: cwm-license@cisco.com.
Cisco ASR 9000 Series Aggregration Services Router Right-To-Use (RTU) Licensing
Here are on-line locations of the Cisco ASR 9000 Series Aggregation Services Router Right-To-Use (RTU) licensing docs:http://www.cisco.com/en/US/docs/routers/asr9000/hardware/Prodlicense/A9k-AIP-LIC-B.html
http://www.cisco.com/en/US/docs/routers/asr9000/hardware/Prodlicense/A9k-AIP-LIC-E.html
NoteLayer 3 VPNs are only to be used after you have purchased a license. Cisco will enforce the RTU of L3VPNs in follow on releases. You should contact Cisco, or check the release notes for the follow on release before upgrading for directions on how to install the license as part of the upgrade - otherwise the L3VPN feature may be affected.
The activation of VRF capability still requires the use of the appropriate per line card license (A9K-IVRF-LIC / A9K-AIP-LIC-B / A9K-AIP-LIC-E). Please contact your sales representative for more details.
Firmware Support
To check the firmware code running on the Cisco ASR 9000 Series Router, run the show fpd package command in admin mode.
In upgrading from Release 3.7.3 or earlier releases, you may be expected to do a one-time FPD upgrade for any firmware images that may have changed since the last release. Refer to the documents at http://www.cisco.com/web/Cisco_IOS_XR_Software/index.html for upgrade instructions.
RP/0/RSP0/CPU0:router(admin)#show fpd package =============================== ================================================ Field Programmable Device Package ================================================ SW Min Req Min Req Card Type FPD Description Type Subtype Version SW Ver HW Vers ==================== ========================== ==== ======= =========== ======== ========= ASR-9912-BPID2 Can Bus Ctrl (CBC) BP2 bp cbc 7.104 0.00 0.1 Can Bus Ctrl (CBC) BP2 lc cbc 7.104 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9922-BPID2 Can Bus Ctrl (CBC) BP2 bp cbc 7.104 0.00 0.1 Can Bus Ctrl (CBC) BP2 lc cbc 7.104 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-BPID2-10-SLOT Can Bus Ctrl (CBC) BP2 bp cbc 7.104 0.00 0.1 Can Bus Ctrl (CBC) BP2 lc cbc 7.104 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-BPID2-6-SLOT Can Bus Ctrl (CBC) BP2 bp cbc 7.104 0.00 0.1 Can Bus Ctrl (CBC) BP2 lc cbc 7.104 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9922-SFC110 Can Bus Ctrl (CBC) MTFC fc cbc 28.05 0.00 0.1 Fabric Ctrl0 MTFC fc fpga7 1.02 0.00 0.1 Can Bus Ctrl (CBC) MTFC lc cbc 28.05 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9912-SFC110 Can Bus Ctrl (CBC) SSFC fc cbc 32.04 0.00 0.1 Fabric Ctrl0 MTFC fc fpga7 1.02 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9010-FAN Can Bus Ctrl (CBC) FAN ft cbc 4.02 0.00 0.1 Can Bus Ctrl (CBC) FAN lc cbc 4.02 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9006-FAN Can Bus Ctrl (CBC) FAN ft cbc 5.02 0.00 0.1 Can Bus Ctrl (CBC) FAN lc cbc 5.02 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9922-FAN Can Bus Ctrl (CBC) MFAN ft cbc 29.11 0.00 0.1 Can Bus Ctrl (CBC) MFAN lc cbc 29.11 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9912-FAN Can Bus Ctrl (CBC) SFAN ft cbc 31.03 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9010-FAN-V2 Can Bus Ctrl (CBC) FAN ft cbc 29.11 0.00 0.1 Can Bus Ctrl (CBC) FAN lc cbc 29.11 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9001-FAN Can Bus Ctrl (CBC) FAN ft cbc 24.114 0.00 0.1 Can Bus Ctrl (CBC) FAN lc cbc 24.114 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-40GE-B Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.06 0.00 0.1 PortCtrl LC2 lc fpga2 0.10 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-4T-B Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.08 0.00 0.1 LCClkCtrl LC2 lc cpld3 0.03 0.00 0.1 PortCtrl LC2 lc fpga2 0.10 0.00 0.1 PHY LC2 lc fpga3 14.44 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-8T/4-B Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.08 0.00 0.1 LCClkCtrl LC2 lc cpld3 0.03 0.00 0.1 PortCtrl LC2 lc fpga2 0.10 0.00 0.1 PHY LC2 lc fpga3 14.44 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-2T20GE-B Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.11 0.00 0.1 LCClkCtrl LC2 lc cpld3 0.10 0.00 0.1 PortCtrl LC2 lc fpga2 0.16 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-40GE-E Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.06 0.00 0.1 PortCtrl LC2 lc fpga2 0.10 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-4T-E Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.08 0.00 0.1 LCClkCtrl LC2 lc cpld3 0.03 0.00 0.1 PortCtrl LC2 lc fpga2 0.10 0.00 0.1 PHY LC2 lc fpga3 14.44 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-8T/4-E Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.08 0.00 0.1 LCClkCtrl LC2 lc cpld3 0.03 0.00 0.1 PortCtrl LC2 lc fpga2 0.10 0.00 0.1 PHY LC2 lc fpga3 14.44 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-2T20GE-E Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.11 0.00 0.1 LCClkCtrl LC2 lc cpld3 0.10 0.00 0.1 PortCtrl LC2 lc fpga2 0.16 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-8T-B Can Bus Ctrl (CBC) LC3 lc cbc 6.11 0.00 0.1 CPUCtrl LC3 lc cpld1 1.02 0.00 0.1 PHYCtrl LC3 lc cpld2 0.08 0.00 0.1 LCClkCtrl LC3 lc cpld3 0.03 0.00 0.1 DB CPUCtrl LC3 lc cpld4 1.03 0.00 0.1 PortCtrl LC3 lc fpga2 0.11 0.00 0.1 Raven LC3 lc fpga1 1.03 0.00 0.1 ROMMONB LC3 lc rommon 1.03 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-16T/8-B Can Bus Ctrl (CBC) LC3 lc cbc 6.12 0.00 0.1 CPUCtrl LC3 lc cpld1 1.02 0.00 0.1 PHYCtrl LC3 lc cpld2 0.04 0.00 0.1 LCClkCtrl LC3 lc cpld3 0.01 0.00 0.1 DB CPUCtrl LC3 lc cpld4 1.03 0.00 0.1 PortCtrl LC3 lc fpga2 0.01 0.00 0.1 Raven LC3 lc fpga1 1.03 0.00 0.1 ROMMONB LC3 lc rommon 1.03 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-8T-E Can Bus Ctrl (CBC) LC3 lc cbc 6.11 0.00 0.1 CPUCtrl LC3 lc cpld1 1.02 0.00 0.1 PHYCtrl LC3 lc cpld2 0.08 0.00 0.1 LCClkCtrl LC3 lc cpld3 0.03 0.00 0.1 CPUCtrl LC3 lc cpld4 1.03 0.00 0.1 PortCtrl LC3 lc fpga2 0.11 0.00 0.1 Raven LC3 lc fpga1 1.03 0.00 0.1 ROMMONB LC3 lc rommon 1.03 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-16T/8-E Can Bus Ctrl (CBC) LC3 lc cbc 6.12 0.00 0.1 CPUCtrl LC3 lc cpld1 1.02 0.00 0.1 PHYCtrl LC3 lc cpld2 0.04 0.00 0.1 LCClkCtrl LC3 lc cpld3 0.01 0.00 0.1 DB CPUCtrl LC3 lc cpld4 1.03 0.00 0.1 PortCtrl LC3 lc fpga2 0.01 0.00 0.1 Raven LC3 lc fpga1 1.03 0.00 0.1 ROMMONB LC3 lc rommon 1.03 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-40GE-L Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.06 0.00 0.1 PortCtrl LC2 lc fpga2 0.10 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-4T-L Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.08 0.00 0.1 LCClkCtrl LC2 lc cpld3 0.03 0.00 0.1 PortCtrl LC2 lc fpga2 0.10 0.00 0.1 Serdes Upgrade LC2 lc fpga3 14.44 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-8T/4-L Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.08 0.00 0.1 LCClkCtrl LC2 lc cpld3 0.03 0.00 0.1 PortCtrl LC2 lc fpga2 0.10 0.00 0.1 Serdes Upgrade LC2 lc fpga3 14.44 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-2T20GE-L Can Bus Ctrl (CBC) LC2 lc cbc 2.03 0.00 0.1 CPUCtrl LC2 lc cpld1 1.00 0.00 0.1 PHYCtrl LC2 lc cpld2 0.11 0.00 0.1 LCClkCtrl LC2 lc cpld3 0.10 0.00 0.1 Tomcat LC2 lc fpga2 0.16 0.00 0.1 Bridge LC2 lc fpga1 0.44 0.00 0.1 ROMMONB LC2 lc rommon 1.05 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-8T-L Can Bus Ctrl (CBC) LC3 lc cbc 6.11 0.00 0.1 CPUCtrl LC3 lc cpld1 1.02 0.00 0.1 PHYCtrl LC3 lc cpld2 0.08 0.00 0.1 LCClkCtrl LC3 lc cpld3 0.03 0.00 0.1 CPUCtrl LC3 lc cpld4 1.03 0.00 0.1 PortCtrl LC3 lc fpga2 0.11 0.00 0.1 Raven LC3 lc fpga1 1.03 0.00 0.1 ROMMONB LC3 lc rommon 1.03 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-16T/8-L Can Bus Ctrl (CBC) LC3 lc cbc 6.12 0.00 0.1 CPUCtrl LC3 lc cpld1 1.02 0.00 0.1 PHYCtrl LC3 lc cpld2 0.04 0.00 0.1 LCClkCtrl LC3 lc cpld3 0.01 0.00 0.1 DB CPUCtrl LC3 lc cpld4 1.03 0.00 0.1 PortCtrl LC3 lc fpga2 0.01 0.00 0.1 Raven LC3 lc fpga1 1.03 0.00 0.1 ROMMONB LC3 lc rommon 1.03 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-SIP-700 Can Bus Ctrl (CBC) LC5 lc cbc 3.06 0.00 0.1 CPUCtrl LC5 lc cpld1 0.15 0.00 0.1 QFPCPUBridge LC5 lc fpga2 5.14 0.00 0.1 NPUXBarBridge LC5 lc fpga1 0.23 0.00 0.1 ROMMONB LC5 lc rommon 1.04 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-SIP-500 Can Bus Ctrl (CBC) LC5 lc cbc 3.06 0.00 0.1 CPUCtrl LC5 lc cpld1 0.15 0.00 0.1 QFPCPUBridge LC5 lc fpga2 5.14 0.00 0.1 NPUXBarBridge LC5 lc fpga1 0.23 0.00 0.1 ROMMONB LC5 lc rommon 1.04 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-SIP-700-8G Can Bus Ctrl (CBC) LC5 lc cbc 3.06 0.00 0.1 CPUCtrl LC5 lc cpld1 0.15 0.00 0.1 QFPCPUBridge LC5 lc fpga2 5.14 0.00 0.1 NPUXBarBridge LC5 lc fpga1 0.23 0.00 0.1 ROMMONB LC5 lc rommon 1.35 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-RSP-2G Can Bus Ctrl (CBC) RSP2 lc cbc 1.03 0.00 0.1 CPUCtrl RSP2 lc cpld2 1.18 0.00 0.1 IntCtrl RSP2 lc fpga2 1.15 0.00 0.1 ClkCtrl RSP2 lc fpga3 1.23 0.00 0.1 UTI RSP2 lc fpga4 3.08 0.00 0.1 PUNT RSP2 lc fpga1 1.05 0.00 0.1 ROMMONB RSP2 lc rommon 1.06 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-RSP-4G Can Bus Ctrl (CBC) RSP2 lc cbc 1.03 0.00 0.1 CPUCtrl RSP2 lc cpld2 1.18 0.00 0.1 IntCtrl RSP2 lc fpga2 1.15 0.00 0.1 ClkCtrl RSP2 lc fpga3 1.23 0.00 0.1 UTI RSP2 lc fpga4 3.08 0.00 0.1 PUNT RSP2 lc fpga1 1.05 0.00 0.1 ROMMONB RSP2 lc rommon 1.06 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-RSP-8G Can Bus Ctrl (CBC) RSP2 lc cbc 1.03 0.00 0.1 CPUCtrl RSP2 lc cpld2 1.18 0.00 0.1 IntCtrl RSP2 lc fpga2 1.15 0.00 0.1 ClkCtrl RSP2 lc fpga3 1.23 0.00 0.1 UTI RSP2 lc fpga4 3.08 0.00 0.1 PUNT RSP2 lc fpga1 1.05 0.00 0.1 ROMMONB RSP2 lc rommon 1.06 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-RSP440-TR Can Bus Ctrl (CBC) RSP3 lc cbc 16.115 0.00 0.1 ClockCtrl0 RSP3 lc fpga2 1.06 0.00 0.1 UTI RSP3 lc fpga3 4.09 0.00 0.1 CPUCtrl RSP3 lc fpga1 0.10 0.00 0.1 ROMMONB RSP3 lc rommon 0.71 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-RSP440-SE Can Bus Ctrl (CBC) RSP3 lc cbc 16.115 0.00 0.1 ClockCtrl0 RSP3 lc fpga2 1.06 0.00 0.1 UTI RSP3 lc fpga3 4.09 0.00 0.1 CPUCtrl RSP3 lc fpga1 0.10 0.00 0.1 ROMMONB RSP3 lc rommon 0.71 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9922-RP-TR Can Bus Ctrl (CBC) MTRP lc cbc 25.02 0.00 0.1 Fabric Ctrl3 MTFC lc fpga10 1.02 0.00 0.1 Fabric Ctrl4 MTFC lc fpga11 1.02 0.00 0.1 Fabric Ctrl5 MTFC lc fpga12 1.02 0.00 0.1 Fabric Ctrl6 MTFC lc fpga13 1.02 0.00 0.1 CPUCtrl1 lc fpga2 1.03 0.00 0.1 ClkCtrl lc fpga3 1.03 0.00 0.1 IntCtrl lc fpga4 1.04 0.00 0.1 UTI lc fpga5 4.09 0.00 0.1 Timex lc fpga6 0.02 0.00 0.1 Fabric Ctrl0 MTFC lc fpga7 1.02 0.00 0.1 Fabric Ctrl1 MTFC lc fpga8 1.02 0.00 0.1 Fabric Ctrl2 MTFC lc fpga9 1.02 0.00 0.1 CPUCtrl0 lc fpga1 1.04 0.00 0.1 ROMMONB MTRP lc rommon 5.11 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9922-RP-SE Can Bus Ctrl (CBC) MTRP lc cbc 25.02 0.00 0.1 Fabric Ctrl3 MTFC lc fpga10 1.02 0.00 0.1 Fabric Ctrl4 MTFC lc fpga11 1.02 0.00 0.1 Fabric Ctrl5 MTFC lc fpga12 1.02 0.00 0.1 Fabric Ctrl6 MTFC lc fpga13 1.02 0.00 0.1 CPUCtrl1 lc fpga2 1.03 0.00 0.1 ClkCtrl lc fpga3 1.03 0.00 0.1 IntCtrl lc fpga4 1.04 0.00 0.1 UTI lc fpga5 4.09 0.00 0.1 Timex lc fpga6 0.02 0.00 0.1 Fabric Ctrl0 MTFC lc fpga7 1.02 0.00 0.1 Fabric Ctrl1 MTFC lc fpga8 1.02 0.00 0.1 Fabric Ctrl2 MTFC lc fpga9 1.02 0.00 0.1 CPUCtrl0 lc fpga1 1.04 0.00 0.1 ROMMONB MTRP lc rommon 5.11 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9900-RP-TR Can Bus Ctrl (CBC) MTRP lc cbc 25.02 0.00 0.1 Fabric Ctrl3 MTFC lc fpga10 1.02 0.00 0.1 Fabric Ctrl4 MTFC lc fpga11 1.02 0.00 0.1 Fabric Ctrl5 MTFC lc fpga12 1.02 0.00 0.1 Fabric Ctrl6 MTFC lc fpga13 1.02 0.00 0.1 CPUCtrl1 lc fpga2 1.03 0.00 0.1 ClkCtrl lc fpga3 1.03 0.00 0.1 IntCtrl lc fpga4 1.04 0.00 0.1 UTI lc fpga5 4.09 0.00 0.1 Timex lc fpga6 0.02 0.00 0.1 Fabric Ctrl0 MTFC lc fpga7 1.02 0.00 0.1 Fabric Ctrl1 MTFC lc fpga8 1.02 0.00 0.1 Fabric Ctrl2 MTFC lc fpga9 1.02 0.00 0.1 CPUCtrl0 lc fpga1 1.04 0.00 0.1 ROMMONB MTRP lc rommon 5.11 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR-9900-RP-SE Can Bus Ctrl (CBC) MTRP lc cbc 25.02 0.00 0.1 Fabric Ctrl3 MTFC lc fpga10 1.02 0.00 0.1 Fabric Ctrl4 MTFC lc fpga11 1.02 0.00 0.1 Fabric Ctrl5 MTFC lc fpga12 1.02 0.00 0.1 Fabric Ctrl6 MTFC lc fpga13 1.02 0.00 0.1 CPUCtrl1 lc fpga2 1.03 0.00 0.1 ClkCtrl lc fpga3 1.03 0.00 0.1 IntCtrl lc fpga4 1.04 0.00 0.1 UTI lc fpga5 4.09 0.00 0.1 Timex lc fpga6 0.02 0.00 0.1 Fabric Ctrl0 MTFC lc fpga7 1.02 0.00 0.1 Fabric Ctrl1 MTFC lc fpga8 1.02 0.00 0.1 Fabric Ctrl2 MTFC lc fpga9 1.02 0.00 0.1 CPUCtrl0 lc fpga1 1.04 0.00 0.1 ROMMONB MTRP lc rommon 5.11 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR9001-RP Can Bus Ctrl (CBC) IMRP lc cbc 22.114 0.00 0.1 MB CPUCtrl lc fpga2 1.14 0.00 0.0 ROMMONB IM RP lc rommon 2.01 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-24x10GE-SE Can Bus Ctrl (CBC) LC6 lc cbc 19.111 0.00 0.0 DBCtrl LC6 lc fpga2 1.03 0.00 0.0 LinkCtrl LC6 lc fpga3 1.01 0.00 0.0 LCCPUCtrl LC6 lc fpga4 1.07 0.00 0.0 ROMMONB LC6 lc rommon 2.00 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-2x100GE-SE Can Bus Ctrl (CBC) LC4 lc cbc 21.110 0.00 0.1 DB IO FPGA1 lc cpld1 1.03 0.00 0.0 MB CPUCtrl lc fpga2 1.08 0.00 0.0 PortCtrl lc fpga3 1.05 0.00 0.0 Imux lc fpga4 1.01 0.00 0.0 Emux lc fpga5 1.03 0.00 0.0 100GIGMAC lc fpga6 39.00 0.00 0.0 ROMMONB LC4 lc rommon 2.00 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-MOD80-SE Can Bus Ctrl (CBC) LC4 lc cbc 20.117 0.00 0.1 DB Ctrl lc fpga2 1.04 0.00 0.0 MB CPUCtrl lc fpga4 1.05 0.00 0.0 ROMMONB LC4 lc rommon 2.00 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-MOD160-SE Can Bus Ctrl (CBC) LC4 lc cbc 20.117 0.00 0.1 DB Ctrl lc fpga2 1.04 0.00 0.0 MB CPUCtrl lc fpga4 1.05 0.00 0.0 ROMMONB LC4 lc rommon 2.00 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-24x10GE-TR Can Bus Ctrl (CBC) LC6 lc cbc 19.111 0.00 0.0 DBCtrl LC6 lc fpga2 1.03 0.00 0.0 LinkCtrl LC6 lc fpga3 1.01 0.00 0.0 LCCPUCtrl LC6 lc fpga4 1.07 0.00 0.0 ROMMONB LC6 lc rommon 2.00 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-2x100GE-TR Can Bus Ctrl (CBC) LC4 lc cbc 21.110 0.00 0.1 DB IO FPGA1 lc cpld1 1.03 0.00 0.0 MB CPUCtrl lc fpga2 1.08 0.00 0.0 PortCtrl lc fpga3 1.05 0.00 0.0 Imux lc fpga4 1.01 0.00 0.0 Emux lc fpga5 1.03 0.00 0.0 100GIGMAC lc fpga6 39.00 0.00 0.0 ROMMONB LC4 lc rommon 2.00 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-MOD80-TR Can Bus Ctrl (CBC) LC4 lc cbc 20.117 0.00 0.1 DB Ctrl lc fpga2 1.04 0.00 0.0 MB CPUCtrl lc fpga4 1.05 0.00 0.0 ROMMONB LC4 lc rommon 2.00 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-MOD160-TR Can Bus Ctrl (CBC) LC4 lc cbc 20.117 0.00 0.1 DB Ctrl lc fpga2 1.04 0.00 0.0 MB CPUCtrl lc fpga4 1.05 0.00 0.0 ROMMONB LC4 lc rommon 2.00 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-8T-TEST Can Bus Ctrl (CBC) LC17 lc cbc 17.214 0.00 0.0 LCCPUCtrl LC6 lc fpga4 0.03 0.00 0.0 ROMMONB LC6 lc rommon 1.04 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-36x10GE-SE Can Bus Ctrl (CBC) LC6 lc cbc 15.103 0.00 0.0 DBCtrl LC6 lc fpga2 1.01 0.00 0.0 LinkCtrl LC6 lc fpga3 1.00 0.00 0.0 LCCPUCtrl LC6 lc fpga4 1.03 0.00 0.0 ROMMONB LC6 lc rommon 2.00 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-36x10GE-TR Can Bus Ctrl (CBC) LC6 lc cbc 15.103 0.00 0.0 DBCtrl LC6 lc fpga2 1.01 0.00 0.0 LinkCtrl LC6 lc fpga3 1.00 0.00 0.0 LCCPUCtrl LC6 lc fpga4 1.03 0.00 0.0 ROMMONB LC6 lc rommon 2.00 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-1x100GE-SE Can Bus Ctrl (CBC) LC4 lc cbc 21.110 0.00 0.1 DB IO FPGA1 lc cpld1 1.03 0.00 0.0 MB CPUCtrl lc fpga2 1.08 0.00 0.0 PortCtrl lc fpga3 1.05 0.00 0.0 Imux lc fpga4 1.01 0.00 0.0 Emux lc fpga5 1.03 0.00 0.0 100GIGMAC lc fpga6 39.00 0.00 0.0 ROMMONB LC4 lc rommon 2.00 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-1x100GE-TR Can Bus Ctrl (CBC) LC4 lc cbc 21.110 0.00 0.1 DB IO FPGA1 lc cpld1 1.03 0.00 0.0 MB CPUCtrl lc fpga2 1.08 0.00 0.0 PortCtrl lc fpga3 1.05 0.00 0.0 Imux lc fpga4 1.01 0.00 0.0 Emux lc fpga5 1.03 0.00 0.0 100GIGMAC lc fpga6 39.00 0.00 0.0 ROMMONB LC4 lc rommon 2.00 0.00 0.0 ---------------------------------------------------------------------------------------------- ASR9001-LC Can Bus Ctrl (CBC) IMLC lc cbc 23.114 0.00 0.1 DB CPUCtrl lc fpga2 1.18 0.00 0.0 EP Gambit lc fpga3 0.08 0.00 0.0 MB CPUCtrl lc fpga4 2.07 0.00 0.0 EP Rogue lc fpga6 1.06 0.00 0.0 EP Sage lc fpga7 1.02 0.00 0.0 ROMMONB IM LC lc rommon 2.01 0.00 0.1 ---------------------------------------------------------------------------------------------- ASR9001-LC-S Can Bus Ctrl (CBC) IMLC lc cbc 23.114 0.00 0.1 DB CPUCtrl lc fpga2 1.18 0.00 0.0 EP Gambit lc fpga3 0.08 0.00 0.0 MB CPUCtrl lc fpga4 2.07 0.00 0.0 EP Rogue lc fpga6 1.06 0.00 0.0 EP Sage lc fpga7 1.02 0.00 0.0 ROMMONB IM LC lc rommon 2.01 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-ISM-100 Can Bus Ctrl (CBC) LC6 lc cbc 18.08 0.00 0.1 CPUCtrl LC6 lc cpld1 0.01 0.00 0.1 Maintenance LC6 lc fpga2 2.13 0.00 0.1 Amistad LC6 lc fpga1 0.33 0.00 0.20 ROMMONB LC6 lc rommon 1.02 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-RSP-3G ClockCtrl0 RSP3 lc fpga2 1.06 0.00 0.1 UTI RSP3 lc fpga3 4.09 0.00 0.1 CPUCtrl RSP3 lc fpga1 0.10 0.00 0.1 ROMMONB RSP3 lc rommon 0.71 0.00 0.1 ---------------------------------------------------------------------------------------------- A9K-RSP-24G ClockCtrl0 RSP3 lc fpga2 1.06 0.00 0.1 UTI RSP3 lc fpga3 4.09 0.00 0.1 CPUCtrl RSP3 lc fpga1 0.10 0.00 0.1 ROMMONB RSP3 lc rommon 0.71 0.00 0.1 ---------------------------------------------------------------------------------------------- SPA-4XT3/E3 SPA E3 Subrate FPGA spa fpga2 1.04 0.00 0.0 SPA T3 Subrate FPGA spa fpga3 1.04 0.00 0.0 SPA I/O FPGA spa fpga1 1.01 0.00 0.0 SPA ROMMON spa rommon 2.12 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-4XCT3/DS0 SPA T3 Subrate FPGA spa fpga2 0.11 0.00 0.100 SPA T3 Subrate FPGA spa fpga2 1.04 0.00 0.200 SPA I/O FPGA spa fpga1 2.08 0.00 0.100 SPA ROMMON spa rommon 2.12 0.00 0.100 ---------------------------------------------------------------------------------------------- SPA-1XCHSTM1/OC3 SPA T3 Subrate FPGA spa fpga2 1.04 0.00 0.0 SPA I/O FPGA spa fpga1 1.08 0.00 0.0 SPA ROMMON spa rommon 2.12 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-24CHT1-CE-ATM SPA T3 Subrate FPGA spa fpga2 1.10 0.00 1.0 SPA I/O FPGA spa fpga1 2.32 0.00 1.0 SPA ROMMON spa rommon 1.03 0.00 1.0 ---------------------------------------------------------------------------------------------- SPA-2CHT3-CE-ATM SPA T3 Subrate FPGA spa fpga2 1.11 0.00 1.0 SPA I/O FPGA spa fpga1 2.22 0.00 1.0 SPA ROMMON spa rommon 1.04 0.00 1.0 ---------------------------------------------------------------------------------------------- SPA-1CHOC3-CE-ATM SPA OC3 Subrate FPGA spa fpga2 2.23 0.00 0.0 SPA I/O FPGA spa fpga1 2.23 0.00 2.0 SPA ROMMON spa rommon 1.04 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-1XCHOC48/DS3 SPA I/O FPGA spa fpga2 1.00 0.00 0.49 SPA I/O FPGA spa fpga3 1.00 0.00 0.52 SPA I/O FPGA spa fpga1 1.36 0.00 0.49 SPA ROMMON spa rommon 2.02 0.00 0.49 ---------------------------------------------------------------------------------------------- SPA-2XCHOC12/DS0 SPA FPGA2 swv1.00 spa fpga2 1.00 0.00 0.0 SPA FPGA swv1.36 spa fpga1 1.36 0.00 0.49 SPA ROMMON swv2.2 spa rommon 2.02 0.00 0.49 ---------------------------------------------------------------------------------------------- A9K-MPA-20X1GE EP I/O FPGA spa fpga3 0.08 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-MPA-2X10GE EP I/O FPGA spa fpga6 1.06 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-MPA-4X10GE EP I/O FPGA spa fpga6 1.06 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-MPA-2X40GE EP Sage spa fpga7 1.03 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-MPA-1X40GE EP Sage spa fpga7 1.03 0.00 0.0 ---------------------------------------------------------------------------------------------- A9K-MPA-8X10GE EP I/O FPGA spa fpga8 1.00 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-8XOC12-POS SPA FPGA swv1.0 spa fpga1 1.00 0.00 0.5 ---------------------------------------------------------------------------------------------- SPA-8XCHT1/E1 SPA I/O FPGA spa fpga1 2.08 0.00 0.0 SPA ROMMON spa rommon 2.12 0.00 0.140 ---------------------------------------------------------------------------------------------- SPA-OC192POS-XFP SPA FPGA swv1.2 hwv2 spa fpga1 1.02 0.00 2.0 ---------------------------------------------------------------------------------------------- SPA-2XOC48POS/RPR SPA FPGA swv1.0 spa fpga1 1.00 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-4XOC48POS/RPR SPA FPGA swv1.0 spa fpga1 1.00 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-8XOC3-POS SPA FPGA swv1.0 spa fpga1 1.00 0.00 0.5 ---------------------------------------------------------------------------------------------- SPA-2XOC12-POS SPA FPGA swv1.0 spa fpga1 1.00 0.00 0.5 ---------------------------------------------------------------------------------------------- SPA-4XOC12-POS SPA FPGA swv1.0 spa fpga1 1.00 0.00 0.5 ---------------------------------------------------------------------------------------------- SPA-10X1GE-V2 SPA FPGA swv1.10 spa fpga1 1.10 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-5X1GE-V2 SPA FPGA swv1.10 spa fpga1 1.10 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-1X10GE-L-V2 SPA FPGA swv1.9 spa fpga1 1.09 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-4XOC3-POS-V2 SPA FPGA swv1.0 spa fpga1 1.00 0.00 0.5 ---------------------------------------------------------------------------------------------- SPA-1X10GE-WL-V2 SPA FPGA swv1.9 spa fpga1 1.09 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-1XOC3-ATM-V2 SPA FPGA swv1.2 spa fpga1 2.02 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-2XOC3-ATM-V2 SPA FPGA swv1.2 spa fpga1 2.02 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-3XOC3-ATM-V2 SPA FPGA swv1.2 spa fpga1 2.02 0.00 0.0 ---------------------------------------------------------------------------------------------- SPA-1XOC12-ATM-V2 SPA FPGA swv1.2 spa fpga1 2.02 0.00 0.0 ----------------------------------------------------------------------------------------------Determining Your Software Version
ProcedureTo determine the version of Cisco IOS XR Software running on your router, log in to the router and enter the show version command:
Software Features Introduced in Cisco IOS XR Software Release 4.3.2 for Cisco ASR 9000 Series Aggregation Service Router
extcommunity-set
Named Form for Extcommunity-set Bandwidth
A bandwidth set provides link bandwidth extended community attribute support to perform unequal load balancing for multi-homed sites.
For more information on configuring per-neighbor link bandwidth, see the Implementing BGP chapter in the Cisco ASR 9000 Series Aggregation Services Router Routing Configuration Guide. For complete command reference of the BGP commands, see the Border Gateway Protocol Commands chapter in the Cisco ASR 9000 Series Aggregation Services Router Routing Command Reference.
Provider Backbone Bridging Ethernet VPN
The Provider Backbone Bridge (PBB) Ethernet VPN ( EVPN) is a next generation L2VPN solution that addresses resiliency and forwarding policy requirements. This feature introduces advanced multihoming options, support for multi-pathing and user-defined BGP policy capabilities to Ethernet L2VPNs. PBB EVPN uses BGP for MAC distribution and learning over the packet-switched network (PSN).
For more information on PBB EVPN, see the Implementing IEEE 802.1ah Provider Backbone Bridge module in the Cisco ASR 9000 Series Aggregation Services Router L2VPN and Ethernet Services Configuration Guide. For more information on PBB EVPN commands, see the Cisco ASR 9000 Series Aggregation Services Router L2VPN and Ethernet Services Command Reference.
TCP MSS Adjustment
The TCP Maximum Segment Size (MSS) Adjustment feature allows the configuration of Maximum Segment Size (MSS) on transient packets that traverse a router. TCP MSS Adjustment is used on a GRE tunnel interface or VLAN sub-interface on a physical Ethernet interface on ASR 9000 Enhanced Ethernet Line Card to enable the transit traffic of TCP flows to be a Maximum Segment Size (MSS) below the GRE tunnel interface or VLAN sub-interface MTU so that traffic fragmentation is prevented when a session is established. It needs to be configurable, for a single tunnel interface or VLAN sub-interface, to a specific value.
For more information about the TCP MSS Adjustment feature, see the Implementing Network Stack IPv4 and IPv6 module in the Cisco ASR 9000 Series Aggregation Services Router IP Addresses and Services Configuration Guide. For complete command reference of the Network Stack IPv4 and IPv6 commands, see the Network Stack IPv4 and IPv6 Commands chapter in the Cisco ASR 9000 Series Aggregation Services Router IP Addresses and Services Command Reference.
Many-to-One Address Mapping in NAT on ISM
The process where NAT44 address translation performs an address mapping of several private IP addresses to one public IP address is known as many-to-one address mapping. Ensure that you specify the limit for the number of private addresses to be mapped to a single public address. The range for this limit is 1 to 65,535.
For more information on many-to-one address mapping, see the Man-to-One Address Mapping module in the Cisco IOS XR Carrier Grade NAT Configuration Guide for the Cisco CRS Router. For more information on Man-to-One Address Mapping commands, see the Cisco IOS XR Carrier Grade NAT Command Reference for the Cisco CRS Router.
Differentiated Services Code Point (DSCP) Marking support for TACACS packets
Differentiated Services is a Quality of Service (QoS) architecture that manages the data traffic in a network by using the principle of traffic classification. In this model, the traffic is divided into classes and the data packets are forwarded to the corresponding classes. Based on the priority of the network traffic, the different classes are managed.
To classify traffic, Differentiated Services uses Differentiated Services Code Point (DSCP). It is a 6-bit field in the Type of Service (ToS) byte in the IP header. Based on the DSCP value, the user is able to classify the data traffic and forward packets to the next destination.
You can set the value of DSCP. For a single connection, set the DSCP value on the socket while connecting to the server. In this way, all the outgoing packets will have the same DSCP value in their IP headers. For multiple connections, the DSCP value is set on the available open sockets. Use the tacacs-server ipv4 command to set the DSCP value.
For more information about the DSCP Marking support for TACACS packets feature, see the Differentiated Services Code Point (DSCP) Marking support for TACACS packets module in the Cisco ASR 9000 Series Aggregation Services Router System Security Configuration Guide. For complete command reference of DSCP command, see the Authentication, Authorization, And Accounting Commands chapter in the Cisco ASR 9000 Series Aggregation Services Router System Security Command Reference
Implementing Lawful Intercept
Lawful Intercept is not a part of the Cisco IOS XR software by default. You have to install it separately by installing and activating asr9k-li-px.pie.
For more information about activating and deactivating the Lawful Intercept package, see the Installing and Activating the PIE module in the Cisco ASR 9000 Series Aggregation Services Router System Security Configuration Guide. For complete command reference of Lawful Intercept commands, see the Lawful Intercept Commands chapter in the Cisco ASR 9000 Series Aggregation Services Router System Security Command Reference
Hardware Features Introduced in Cisco IOS XR Software Release 4.3.2 for the Cisco ASR 9000 Series Router
- ASR 9900 Route Processor for Service Edge (ASR-9900-RP-SE)
- ASR 9900 Route Processor for Packet Transport (ASR-9900-RP-TR)
- ASR 9912 Fan Tray (ASR-9912-FAN 3kW)
- AC Power Module (PWR-3KW-AC-V2 ASR 9912)
- Switch Fabric Card/110G (ASR-9912-SFC110)
- ASR 9912 10 Line Card Slot AC Chassis w/ PEM V2 (ASR-9912-AC)
- The GLC-ZX-SMD optical transceiver is supported on Cisco ASR 9000 Series Router.
- The QSFP-40G-CSR4 optical transceiver that enables links up to 300 m over OM3 multi-mode fiber in a QSFP form factor is supported.
Important Notes
For Cisco IOS XR Software Release 4.2, the Cisco ASR 9000 Series Aggregation Services Router does not support the following inventory schemas:- vkg_invmgr_adminoper.xsd- vkg_invmgr_common.xsd- vkg_invmgr_oper.xsd
- Only MLPPP encapsulation channels on the OC-12 SONET interface can be protected by IP-FRR in Cisco IOS XR software Release 3.9.0 and above.
- For Cisco IOS XR software Release 3.9.0 and above the SIP 700 with the 2-Port Channelized OC-12/DS0 SPA does not support SDH (including all the mappings under SDH) or DS0 mappings.
- For Cisco IOS XR software Release 3.9.0 and above the SIP 700 with the 2-Port Channelized OC-12/DS0 SPA does not support ATM or POS.
- For Cisco IOS XR software Release 3.9.0 and above the SIP 700 with the 2-Port Channelized OC-12/DS0 SPA does not support MPLS/Traffic Engineering FRR.
- For Cisco IOS XR software Release 4.0.1 and above the SIP 700 with the 1-Port Channelized OC48/STM16 DS3 SPA does not support MPLS/Traffic Engineering FRR.
- For Cisco IOS XR software Release 4.0.1 and above the SIP 700 with the 1-Port Channelized OC48/STM16 DS3 SPA, the 2-Port Channelized OC-12/DS0 SPA , the 8-Port OC12/STM4 SPA , and the 2-Port OC-48/STM16 SPA Layer 2VPN support only includes FR.
- Country-specific laws, regulations, and licenses—In certain countries, use of these products may be prohibited and subject to laws, regulations, or licenses, including requirements applicable to the use of the products under telecommunications and other laws and regulations; customers must comply with all such applicable laws in the countries in which they intend to use the products.
- Card fan controller, and RSP removal—For all card removal and replacement (including fabric cards, line cards, fan controller, and RSP) follow the instructions provided by Cisco to avoid impact to traffic. See the Cisco ASR 9000 Series Aggregation Services Router Getting Started Guide for procedures.
- Exceeding Cisco testing—If you intend to test beyond the combined maximum configuration tested and published by Cisco, contact your Cisco Technical Support representative to discuss how to engineer a large-scale configuration maximum for your purpose.
- Installing a Line Card—For a fully populated 40-port high density Line Card with cable optics, maintenance time required for card replacement is higher. For more information about Line Card installation and removal, refer to the Cisco ASR 9000 Aggregation Services Router Ethernet Line Card Installation Guide.
- Serial Interfaces Out of Order in "show ip interface brief" Command—The show ip interface brief command might display interfaces out of order if different types of serialization are used on the SPA cards. The serial interfaces are displayed in the show ip interface brief command output in the order shown in the example below: The ordering is based on: This may be confusing (the interfaces appear out of order) for the user who is accustomed to IOS. Example output: With multiple cards:
Serial0/2/0/1/1/1:0 (t3/t1) Serial0/2/0/1/2/1:0 Serial0/2/0/1/3/1:0 Serial0/2/0/1/4/1:0 Serial0/2/0/1/5/1:0 Serial0/2/0/1/6/1:0 Serial0/2/0/1/7/1:0 Serial0/2/0/1/8/1:0 Serial0/2/0/1/9/1:0 Serial0/2/0/1/10/1:0 Serial0/2/0/1/11/1:0 Serial0/2/0/1/12/1:0 Serial0/2/0/0/1/1/1:0 (vt15) Serial0/2/0/0/2/1/1:0 Serial0/2/0/0/3/1/1:0 Serial0/2/0/0/4/1/1:0 Serial0/2/0/0/5/1/1:0 Serial0/2/0/0/6/1/1:0 Serial0/2/0/0/7/1/1:0 Serial0/2/0/0/8/1/1:0 Serial0/2/0/0/9/1/1:0 Serial0/2/0/0/10/1/1:0 Serial0/2/0/0/11/1/1:0 Serial0/2/0/0/12/1/1:0 Multilink 0/2/0/0/1 Serial0/2/1/0/1 (t3) Serial0/2/1/1/1/1:0 (t3/t1) Serial0/2/1/1/2/1:0 Serial0/2/1/1/3/1:0 Serial0/2/1/1/4/1:0 Serial0/2/1/1/5/1:0 Serial0/2/1/1/6/1:0 Serial0/2/1/1/7/1:0 Serial0/2/1/1/8/1:0 Serial0/2/1/1/9/1:0 Serial0/2/1/1/10/1:0 Serial0/2/1/1/11/1:0 Serial0/2/1/1/12/1:0 Serial0/6/0/1/1/1:0 Serial0/6/0/1/2/1:0 Serial0/6/0/1/3/1:0 Serial0/6/0/1/4/1:0 Serial0/6/0/1/5/1:0 Serial0/6/0/1/6/1:0 Serial0/6/0/1/7/1:0 Serial0/6/0/1/8/1:0 Serial0/6/0/1/9/1:0 Serial0/6/0/1/10/1:0 Serial0/6/0/1/11/1:0 Serial0/6/0/1/12/1:0 Serial0/6/0/0/1/1/1:0 Serial0/6/0/0/2/1/1:0 Serial0/6/0/0/3/1/1:0 Serial0/6/0/0/4/1/1:0 Serial0/6/0/0/5/1/1:0 Serial0/6/0/0/6/1/1:0 Serial0/6/0/0/7/1/1:0 Serial0/6/0/0/8/1/1:0 Serial0/6/0/0/9/1/1:0 Serial0/6/0/0/10/1/1:0 Serial0/6/0/0/11/1/1:0 Serial0/6/0/0/12/1/1:0 Multilink 0/6/0/0/1 Serial0/6/1/0/1 Serial0/6/1/1/1/1:0 Serial0/6/1/1/2/1:0 Serial0/6/1/1/3/1:0 Serial0/6/1/1/4/1:0 Serial0/6/1/1/5/1:0 Serial0/6/1/1/6/1:0 Serial0/6/1/1/7/1:0 Serial0/6/1/1/8/1:0 Serial0/6/1/1/9/1:0 Serial0/6/1/1/10/1:0 Serial0/6/1/1/11/1:0 Serial0/6/1/1/12/1:0- Starting with Cisco IOS XR Software Release 3.9 the pw-class class name encapsulation mpls command control-word option default is now disable -In Cisco IOS XR Software Release 3.9 and above the control word is disabled by default. To configure the control word, enter the control-word keyword shown in the following example:
pw-class class1 encapsulation mpls control-word- For configured policer rates of less than 1 Mbps, the actual policer rate can be approximately 10 percent less than the configured rate. For example, for a configured policer rate of 500 kbps, the actual policer rate is 448 kbps due to a granularity round down in hardware.
- In Cisco ASR 9000 Series Aggregation Services Router Software Release 4.0.0, the minimum configurable logging buffered size has been increased to 307200. Any configuration with a value less than 307200 fails to upgrade to Release 4.0.1.
- dsu mode Command Default— For E3 interfaces on the 4-Port Clear Channel T3/E3 SPA that interoperate with E3 interfaces on a Cisco 10000 Series router, the default data service unit (DSU) mode is digital-link. To change the DSU mode to cisco, configure scrambling.
- Starting from Cisco IOS XR Software Release 4.0.0, the hw-module location <LOC> reload warm command is disabled. As a result, the warm reload feature also has been disabled.
- In Cisco ASR 9000 Series Aggregation Services Router Software Release 4.1.0, you use the cablelength short command to set a cable length of 655 feet or shorter for a DS1 link on a 4-Port Channelized T1/E1 SPA. The cablelength short command options are listed as follows:
However, when using the cablelength short command on a 4-Port Channelized T1/E1 SPA in Cisco ASR 9000 Series Aggregation Services Router Software Release 4.1.0, only the 133ft option (for cable lengths from 0 to 133 feet) works. The other values that are greater than 133 feet (266, 399, 533, or 655) all cause the T1 controller to go down. The workaround is to restart the controller after you set the cable length to 266, 399, 533, or 655 feet. The cablelength long command works correctlyRP/0/RSP0/CPU0:vkg_ro1_a(config-t1)#cablelength short ? 133ft 0-133ft 266ft 134-266ft 399ft 267-399ft 533ft 400-533ft 655ft 534-655ft
Caveats
Caveats describe unexpected behavior in Cisco IOS XR Software releases. Severity-1 caveats are the most serious caveats; severity-2 caveats are less serious.
This section lists the caveats for Cisco ASR 9000 Series Aggregation Services Router Software Release4.3.2 and the Cisco ASR 9000 Series Aggregation Services Router platform.
- Cisco IOS XR Caveats
- Caveats Specific to the Cisco ASR 9000 Series Aggregation Services Router
- Caveats Specific to the ASR 9001 Router
Cisco IOS XR Caveats
The following open caveats apply to Cisco IOS XR Software Release and are not platform specific:
- CSCuh83194 Basic Description: No response from 'l2vpn_mgr' within timeout period, when the no l2vpn command is executed. Symptom The "No response from l2vpn_mgr" console message is seen after the no l2vpn command is executed. During this period, l2vpn_mgr is mutex blocked and it takes about 15 mins to commit this changes/recover. Conditions: This occurs when L2VPN configuration is removed by executing the no l2vpn command. Workaround: None.
- CSCui57313 Basic Description: PIM/PIM6 ITAL register fails with VRFs having name starting with "all". Symptom On a router running Cisco IOS-XR software, the show pim related commands may get stuck. Modifying the multicast or PIM configuration fails. Conditions: This happens when a VRF with name beginning with "all" is configured. When this occurs, every subsequent VRF that is created, even if the name of the newly created VRF does not begin with "all", blocks the PIM/PIM6 processes. Workaround: Avoid naming VRFs beginning with "all".
- CSCue78677 Basic Description: Memory leak seen on XML dedicated agent. Symptom System fails to properly free the memory allocated while processing the "get XML query" query, provided with large number of Broader Gateway Protocol (BGP) configurations. It happens even after the XML session is terminated. Note: The xml_tty_agent process leaks some chunk of memory, for each iteration, for example 328 bytes of memory. Conditions: Execute the "get XML query" for BGP with large number of BGP configurations. Workaround: None.
Caveats Specific to the Cisco ASR 9000 Series Aggregation Services Router
The following caveats are specific to the Cisco ASR 9000 Series Aggregation Services Router platform:
- CSCui95985 Basic Description: The CISCO-SUBSCRIBER-SESSION-MIB does not work after RSP fail-over in the Cisco ASR 9010 cluster. Symptom In the event of the Cisco ASR 9010 cluster switch-over from active to backup or vice-versa, the CISCO-SUBSCRIBER-SESSION-MIB MIBS fail to function or respond. Conditions: The Cisco ASR 9010 cluster switch-over from active to backup or vice-versa. Workaround: None.
- CSCuh36938 Basic Description: %PLATFORM-ENVMON-4-CARD_VOLTAGE_ALARM seen on the Cisco ASR 9912 chassis and RSP3. Symptom The Cisco ASR9000 RSP440/ASR 9922 RP/ASR9900 RP system displays the following logs (voltage alarms) on console during bootup: RP/0/RSP0/CPU0: envmon[206]: %PLATFORM-ENVMON-4-CARD_VOLTAGE_ALARM : Voltage sensor alarm slot 0/RSP1/CPU0, sensor VP1P2_SERDES_PLL_DAO measured 2500 mV and out of operational range 1177 - 1223 mV RP/0/RSP0/CPU0: eem_ed_hardware[189]: Messge received content : Event 4 NodeId: 0x51 Threshold CARD_VOLTAGE_ALARM Info Sensor: VP1P2_SERDES_PLL_DAO Severity 0x8 Frutype 0x8 Alarm_raised 1 Alarm_type 2 RP/0/RSP0/CPU0: envmon[206]: %PLATFORM-ENVMON-2-ENV_CONDITION : Outstanding environmental condition exists in the chassis RP/0/RSP0/CPU0: envmon[206]: %PLATFORM-ENVMON-4-CARD_VOLTAGE_ALARM_CLEAR : Voltage sensor alarm cleared slot 0/RSP1/CPU0, sensor VP1P2_SERDES_PLL_DAO measured 1199 mV and returned to operational range. Conditions: This occurs during the Cisco ASR9000 RSP440 system bootup. Workaround: None.
- CSCui70014 Basic Description: Cisco ASR9000 RSP440 displays voltage alarms on console. Symptom The Cisco ASR9000 RSP440 system displays the following logs (voltage alarms) on console during bootup: RP/1/RSP0/CPU0: envmon[207]: %PLATFORM-ENVMON-4-CARD_VOLTAGE_ALARM : Voltage sensor alarm slot 1/RSP0/CPU0, sensor VP7P0 measured 6997 mV and out of operational range 3387 - 3614 mV. Conditions: This occurs during the Cisco ASR9000 RSP440 system bootup. Workaround: None.
- CSCui11548 Basic Description: NAT44 pairing missing after ISM or router reload, UIDB mis-programming. Symptom NAT44 pairing missing after ISM or router reload, incorrect UIDB peer programming. Conditions: This happens on ISM module reload. Workaround: Restart the process cgn_ma one and clear UIDB using a CLI command.
- CSCui48557 Basic Description: Remove and re-add ACEs of ACL lead to miss programming in hardware. Symptom After editing two or more IPv4 or IPv6 ACLs already applied on an interface, the change does not take place. Sometimes, the affected ACLs appear differently in show access-list ipv4 ACL name and show access-list ipv4 ACL name hardware ingress location applied node command. The definition of ACL is out of sync between Control Plane and Data Plane. Conditions: Thos happens under the following conditions: Two or more ACLs are edited at the same time (changing/updating the content of ACE, within an ACL). The ACL has already been applied to at least one interface in the system. If the ACL is defined but not used anywhere, this problem will not occur. Editing ACLs that is non-regular ACL. The following are not regular ACLs: The ACL is compressed. The ACE is previously classic ACE (i.e., contains no object-groups), but after editing, it contains object-groups. The ACE previously contains object-group ACE, after editing, it still contains object-group. The ACE previously contains object-group, after editing, it no longer contains object-group. The ACE is deleted or added, and it contains object-group. The ACE is deleted or added, it contains no object-group, but the other, not-changed ACE in the same ACL contains object-group ACE. The ACE is deleted or added, it contains no object-group, but the ACL is compressed. Workaround: Edit non-regular ACLs one by one.
- CSCuh06985 Basic Description: IGMP snooping: querier cannot send msg after the second route processor switchover. Symptom When internal-querier is the Querier, it cannot be restored after the second route processor switchover (RPSO). Then IGMP snooping does not restore all groups. Due to this, the traffic is lost. Conditions: This occurs when internal-querier is the Querier and RPSO happens for the second time. Workaround: None.
- CSCud37497 Basic Description: System configuration fails when downgrading to Cisco IOS XR Software Release 4.2.x from Cisco IOS XR Software Release 4.3.1. Symptom
The system displays the following logs (sample logs) continuously on console and system configuration never completes, while downgrading from Cisco IOS XR Software Release 4.3.1 to Cisco IOS XR Software Release 4.2.x.Conditions: The issue recurs and it is observed while downgrading of Cisco IOS XR Software Release 4.3.1 to Cisco IOS XR Software Releaes 4.2.x. Workaround: Use the disk boot procedure and set the ROM Monitor (rommon) variable TURBOBOOT explicitly with format option, to downgrade successfully from Cisco IOS XR Software Release 4.3.1 to Cisco IOS XR Software Release 4.2.x. Ensure to backup the running-configurations if any, so as to apply the configurations later, after downgrade.RP/0/RSP0/CPU0: cfgmgr-rp[161]: %MGBL-CONFIG-0-INIT_FAILURE : Configuration Manager was unable to initialize the Configuration Namespace Version History module. Error: 'Result too large'. Initialization will be tried again after 60 seconds.Caveats Specific to the ASR 9001 Router
- CSCts82447 Basic Description: attachCon not working. Symptom: After running attachCon, the console will not connect to Line card. The below message is seen on console:
Conditions: This feature is not supported in 4.2.3 as well and will be supported from 4.3.0 onwards. Workaround: Convert AUX port as LC console from RP KSH using the command fill –l 0xd2000198 0x4 0x80000001. To revert back to AUX port, use fill –l 0xd2000198 0x4 0x0. Recovery: None.attachCon is not supported in this release in this chassis typeUpgrading Cisco IOS XR Software
Cisco IOS XR Software is installed and activated from modular packages, allowing specific features or software patches to be installed, upgraded, or downgraded without affecting unrelated processes. Software packages can be upgraded or downgraded on all supported card types, or on a single card (node).
Software packages are installed from package installation envelope (PIE) files that contain one or more software components.
The following URL contains links to information about how to upgrade Cisco IOS XR Software:
http://www.cisco.com/web/Cisco_IOS_XR_Software/index.html
Troubleshooting
Resolving Upgrade File Issues
NoteIn some very rare cases inconsistencies in the content of the internal configuration files can appear. In such situations, to avoid configuration loss during upgrade, the following steps can be optionally done before activating packages:
- Clear the NVGEN cache:
RP/0/RSP0/CPU0:router# run nvgen -F 1- Create a dummy config commit:
RP/0/RSP0/CPU0:router# config RP/0/RSP0/CPU0:router(config)# hostname <hostname> RP/0/RSP0/CPU0:rotuer(config)# commit RP/0/RSP0/CPU0:router(config)# end- Force a commit update by using the reload command. Press n when the confirmation prompt appears:
RP/0/RSP0/CPU0:router# reload Updating Commit Database. Please wait...[OK] Proceed with reload? [confirm]- Press n
In some cases other activity may preclude a reload. The following message may display:
RP/0/RSP0/CPU0:router# reload Preparing system for backup. This may take a few minutes ............System configuration backup in progress [Retry later]If you receive this message wait and then retry the command after some time.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What's New in Cisco Product Documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html.
Subscribe to What's New in Cisco Product Documentation, which lists all new and revised Cisco technical documentation, as an RSS feed and deliver content directly to your desktop using a reader application. The RSS feeds are a free service.
