 Feedback
|
Table Of Contents
Managing Port Services on the Cisco AS5350, Cisco AS5400, and Cisco AS5800
SPE for the NextPort Dial Feature Card
Upgrading SPE Firmware from the Cisco.com FTP Server
Downloading SPE Firmware from the Cisco.com FTP Server to a Local TFTP Server
Copying the SPE Firmware File from the Local TFTP Server to the SPEs
Related Features and Technologies
Supported Standards, MIBs, and RFCs
Comparison of NextPort SPE Command Line Interface (CLI) Commands to MICA Modem CLI Commands
Configuring SPEs to Use an Upgraded Firmware File
Verifying SPE Lines and Port Configuration
Configuring NextPort DFC Ports
Configuring SPE Performance Statistics
Monitoring SPE Performance Statistics
SPE Events and Firmware Statistics
show spe digital disconnect-reason
show spe modem disconnect-reason
Managing Port Services on the Cisco AS5350, Cisco AS5400, and Cisco AS5800
Feature History
This feature module describes Managing Port Services on the Cisco AS5350, Cisco AS5400, and Cisco AS5800 platforms. It includes the overview, the maintenance and troubleshooting tasks, and the Cisco IOS software commands required for port service management.
This document includes the following sections:
•
Supported Standards, MIBs, and RFCs
Feature Overview
The Managing Port Services on the Cisco AS5350, Cisco AS5400, and Cisco AS5800 feature implements port service management for the Cisco AS5350 using the NextPort Dial Feature Card (DFC). The NextPort DFC is a hardware card that processes digital service port technology for the Cisco AS5350. A port is defined as an endpoint on a DFC card through which multiservice tones and data flow. The ports on the NextPort DFC support both modem and digital services. Ports can be aggregated at the slot level of the NextPort module, the Service Processing Element (SPE) level within the NextPort module, and the individual port level.
SPE for the NextPort Dial Feature Card
Instead of the traditional line/modem one-to-one correspondence, lines are mapped to an SPE that resides on the Cisco AS5350 NextPort DFC. Each SPE provides modem services for six ports. Busyout and shutdown can be configured at the SPE or port level. The NextPort DFC introduces the slot and SPE software hierarchy. On the Cisco AS5350, the hierarchy designation is slot/spe. The NextPort DFC slot is defined as a value between 1 and 7. Slot 0 is reserved for the motherboard. Each NextPort DFC provides 18 SPEs. The SPE value ranges from 0 to 17. Because each SPE has six ports, the NextPort DFC has a total of 108 ports. The port value ranges from 0 to 107.
The NextPort DFC performs the following functions:
•
•
•
SPE Firmware
SPE firmware is automatically downloaded to a NextPort DFC from the Cisco AS5350 when you boot the system for the first time, or when you insert a NextPort DFC while the system is operating. When you insert DFCs while the system is operating, the Cisco IOS image recognizes the cards and downloads the required firmware to the cards.
The SPE firmware image is bundled with the universal gateway Cisco IOS image. The SPE firmware image uses an auto detect mechanism, which enables the NextPort DFC to service multiple call types. An SPE detects the call type and automatically configures itself for that operation. For further information on upgrading SPE firmware from the Cisco IOS image, see the "Configuring SPEs to Use an Upgraded Firmware File" section.
The firmware is upgradable independent of Cisco IOS upgrades, and different firmware versions can be configured to run on SPEs in the same NextPort DFC. You can download firmware from the Cisco.com File Transfer Protocol (FTP) server. For further information on upgrading SPE firmware from the Cisco.com FTP server, see the "Upgrading SPE Firmware from the Cisco.com FTP Server" section.
Upgrading SPE Firmware from the Cisco.com FTP Server
Upgrading SPE firmware from the Cisco.com FTP server can be done in two steps:
•
•
Downloading SPE Firmware from the Cisco.com FTP Server to a Local TFTP Server
Note
You can download software from the Cisco.com FTP server using an Internet browser or using an FTP application. Both procedures are described.
Using an Internet Browser
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
Using an FTP Application
Note
Step 1
terminal> ftp Cisco.comConnected to cio-sys.cisco.com.Step 2
Name (Cisco.com:harry): harry331 Password required for harry.Password: <letmein>230-#############################################################230-# Welcome to the Cisco Systems FTP server.230-# This server has a number of restrictions. If you are not familiar230-# with these, please first get and read the /README or /README.TXT file.230-# http://www.cisco.com/acs/info/cioesd.html for more info.230-#############################################################230-Step 3
ftp> cd /cisco/access/5350250-Please read the file README250- it was last modified on Tue May 27 10:07:38 1997 - 48 days ago250-Please read the file README.txt250- it was last modified on Tue May 27 10:07:38 1997 - 48 days ago250 CWD command successful.Step 4
ftp> ls227 Entering Passive Mode (192,31,7,130,218,128)150 Opening ASCII mode data connection for /bin/ls.total 2688drwxr-s--T 2 ftpadmin ftpcio 512 Jun 30 18:11 .drwxr-sr-t 19 ftpadmin ftpcio 512 Jun 23 10:26 ..lrwxrwxrwx 1 root 3 10 Aug 6 1996 README ->README.txt-rw-rw-r-- 1 root ftpcio 2304 May 27 10:07 README.txt-r--r--r-- 1 ftpadmin ftpint 377112 Jul 10 18:08 np-spe-upw-1.0.1.2.bin-r--r--r-- 1 ftpadmin ftpint 635 Jul 10 18:08 SPE-firmware.3.1.30.readmeStep 5
ftp> binary200 Type set to I.Step 6
Step 7
ftp> quitGoodbye.Step 8
server% ls -altotal 596-r--r--r-- 1 280208 Jul 10 18:08 np-spe-upw-1.0.1.2.binserver% pwd/auto/tftpbootStep 9
Copying the SPE Firmware File from the Local TFTP Server to the SPEs
The procedure for copying the SPE firmware file from your local TFTP server to the NextPort DFC is a two-step process. First, transfer the SPE firmware to the universal gateway's Flash memory. Then, configure the SPEs to use the upgrade firmware. The upgrade occurs automatically, either as you leave configuration mode, or as specified in the configuration.
These two steps are performed only once. After you copy the SPE firmware file into Flash memory for the first time, you should not have to perform these steps again.
Note
To transfer SPE firmware to Flash memory, follow these steps to download the universal SPE firmware to Flash memory:
Step 1
Router# show flashSystem flash directory:File Length Name/status1 4530624 c5400-js-mx[498776 bytes used, 16278440 available, 16777216 total]16384K bytes of processor board System flash (Read/Write)Step 2
Router# copy tftp flashStep 3
Router# show flash
Benefits
•
•
•
•
•
•
Related Features and Technologies
•
•
•
•
•
–
–
–
–
•
Related Documents
For further information about managing port services with NextPort DFC, see the following documents that ship with your Cisco AS5350 universal gateway. These documents are also available online and on the documentation CD.
•
•
•
•
•
•
For further information about dial technology, see the following documents:
•
•
•
Supported Platforms
•
•
•
Determining Platform Support Through Cisco Feature Navigator
Cisco IOS software is packaged in feature sets that support specific platforms. To get updated information regarding platform support for this feature, access Cisco Feature Navigator. Cisco Feature Navigator dynamically updates the list of supported platforms as new platform support is added for the feature.
Cisco Feature Navigator is a web-based tool that enables you to determine which Cisco IOS software images support a specific set of features and which features are supported in a specific Cisco IOS image. You can search by feature or release. Under the release section, you can compare releases side by side to display both the features unique to each software release and the features in common.
To access Cisco Feature Navigator, you must have an account on Cisco.com. If you have forgotten or lost your account information, send a blank e-mail to cco-locksmith@cisco.com. An automatic check will verify that your e-mail address is registered with Cisco.com. If the check is successful, account details with a new random password will be e-mailed to you. Qualified users can establish an account on Cisco.com by following the directions at http://www.cisco.com/register.
Cisco Feature Navigator is updated regularly when major Cisco IOS software releases and technology releases occur. For the most current information, go to the Cisco Feature Navigator home page at the following URL:
Availability of Cisco IOS Software Images
Platform support for particular Cisco IOS software releases is dependent on the availability of the software images for those platforms. Software images for some platforms may be deferred, delayed, or changed without prior notice. For updated information about platform support and availability of software images for each Cisco IOS software release, refer to the online release notes or, if supported, Cisco Feature Navigator.
Supported Standards, MIBs, and RFCs
Standards
Carrier protocols
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Error-correcting link-access protocols
•
Compression protocols
•
MIBs
The following MIBs are supported on the Cisco AS5350:
•
•
•
•
•
•
•
•
•
•
•
To obtain lists of MIBs supported by platform and Cisco IOS release and to download MIB modules, go to the Cisco MIB web site on Cisco.com at http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml.
RFCs
No new or modified RFCs are supported by this feature.
Prerequisites
•
•
•
•
•
Comparison of NextPort SPE Command Line Interface (CLI) Commands to MICA Modem CLI Commands
To see how the MICA commands compare to the NextPort SPE commands, use these tables.
.
Configuration Tasks
See the following sections for configuration tasks for Managing Port Services on the Cisco AS5350 Universal Gateway feature. Each task in the list is identified as either optional or required:
•
•
•
•
•
•
•
•
•
•
Configuring Country Code
To set the NextPort DFC to be operational for call set up, you must specify the country name. To specify the country name, perform the following task in global configuration mode:
Configuring SPEs to Use an Upgraded Firmware File
To configure the SPEs to use the upgraded firmware file, perform the following steps, beginning in EXEC mode:
Note
Disabling SPEs
To disable specific SPEs in the NextPort DFC, perform the following steps starting in global configuration mode:
Rebooting SPEs
To reboot specified SPEs, do the following task in privileged EXEC mode:
Configuring Lines and Ports
To configure the lines and ports to dial in to your network, complete the following steps, beginning in global configuration mode:
Verifying SPE Lines and Port Configuration
To verify your SPE line configuration, do the following steps:
Step 1
Router# show speStep 2
Router# show line 1
Note
Configuring NextPort DFC Ports
This section describes how to configure NextPort DFC ports. You must to be in port configuration mode to configure the NextPort ports. The port configuration mode allows you to shut down or put individual ports or ranges of ports in busyout mode. To configure NextPort ports, do the following steps, beginning in global configuration mode:
Clearing Ports
The following privileged EXEC mode commands allow you to clear ports on an SPE:
Configuring SPE Performance Statistics
Depending on the configuration, a call record is displayed on the console, or on the syslog, or on both. The log contains raw data in binary form, which must be viewed using the show commands listed in the "Monitoring SPE Performance Statistics" section. You can configure some aspects of history events by using the following commands in global configuration mode:
Clearing Log Events
The following privileged EXEC mode commands allow you to clear some or all of the log events relating to the SPEs:
Troubleshooting SPEs
This section provides troubleshooting information for your SPEs regardless of service type mode.
Note
•
•
You may additionally configure the following options:
–
–
–
•
When an SPE port is tested as Bad, you may do additional testing by conducting a of internal back-to-back connections and data transfers between two SPE ports. All port test connections occur inside the universal gateway. For example, if mobile users cannot dial into port 2/5 (which is the sixth port on the NextPort DFC in the second chassis slot), attempt a back-to-back test with port 2/5 and a known-functioning port such as port 2/6.
•
Note
A back-to-back test might look like the following example:
Router# test port modem back-to-back 2/10 3/20Repetitions (of 10-byte packets) [1]:*Mar 02 12:13:51.743:%PM_MODEM_MAINT-5-B2BCONNECT:Modems (2/10) and (3/20) connected in back-to-back test:CONNECT33600/V34/LAP*Mar 02 12:13:52.783:%PM_MODEM_MAINT-5-B2BMODEMS:Modems (3/20) and (2/10) completed back-to-back test:success/packets = 2/2
Tip
•
An SPE port failing to connect for a certain number of consecutive times indicates that a problem exists in a specific part or the whole of SPE firmware. Such SPEs have to be recovered by downloading firmware. Any port failing to connect num-failures times is moved to a state based on the port-action value, where you can choose to disable (mark the port as Bad) or recover the port when the SPE is in the idle state and has no active calls. The default for num-failures is 30 consecutive call failures.
Tip
•
The download maintenance activity starts at the set start time and steps through all SPEs that need recovery and the SPEs that need a firmware upgrade. The download maintenance activity starts maintenance on the maximum number of set SPEs for maintenance. The system waits for the window delay time for all the ports on the SPE to become inactive before moving the SPE to the Idle state. Immediately after the SPE moves to the idle state, the system starts to download firmware. If the ports are still in use by the end of window delay time, depending upon the expired-window setting, connections on the SPE ports are shut down and the firmware is downloaded by choosing the drop-call option, or the firmware download is rescheduled to the next download maintenance time by choosing the reschedule option. This process continues until the number of SPEs under maintenance is below max-spes, or until stop-time (if set), or until all SPEs marked for recovery or upgrade have had their firmware reloaded.
Monitoring SPE Performance Statistics
This section documents various SPE performance statistics for the NextPort DFC:
•
SPE Events and Firmware Statistics
To view SPE events and firmware statistics for the NextPort DFCs, enter one or more of the following commands in privileged EXEC mode:
Port Statistics
To view port statistics for the NextPort DFCs, enter one or more of the following commands in privileged EXEC mode:
Digital SPE Statistics
To view digital SPE statistics for the NextPort DFCs, enter one or more of the following commands in privileged EXEC mode:
SPE Modem Statistics
To view SPE modem statistics for the NextPort DFCs, enter one or more of the following commands in privileged EXEC mode:
Configuration Example
The NextPort dial feature card (DFC) provides port service management for the Cisco AS5350.
For further information on configuration examples for the Cisco AS5350, see the Cisco AS5350 Universal Gateway Software Configuration Guide.
Command Reference
This section describes NextPort port management commands for the Cisco AS5350. All other commands used with this platform are documented in the Cisco IOS Release 12.1(1)XD new features documents.
Commands are organized in the following logical groups:
•
•
These groups with their commands in alphabetical order are listed the following subsections.
A master list of all the commands in alphabetical order is given in the "Alphabetical List of Commands" section.
Each command is described in structured reference pages arranged alphabetically in this section.
Service Processing Element (SPE) Management Commands
The following commands manage the SPE level:
Port Management Commands
The following commands manage the port level:
Statistics Commands
The following commands display SPE statistics:
•
(see show port digital log)•
•
Diagnostic and Recovery Commands
The following commands execute diagnostic tests and initiate the recovery mechanism for the SPEs:
•
(see show port digital log)Logging Commands
The following new commands set, display and clear the logging mechanism for the SPEs:
•
(see show port digital log)Alphabetical List of Commands
•
•
•
Command Syntax Conventions
Table 10 describes the syntax used with the commands in this section.
busyout (port)
To disable a port by waiting for the active services on the specified port to terminate, use the busyout port configuration command. To reenable the ports, use the no form of this command.
busyout
no busyout
Syntax Description
This command has no arguments or keywords.
Defaults
no busyout
Command Modes
Port configuration
Command History
Usage Guidelines
Use the no form of this command to re enable the ports.
Examples
The example below will busyout SPE ports 1 to 10 on slot 1
router(config)# port 1/1 1/10router(config-port)# busyoutrouter(config-port)#Related Commands
busyout (spe)
To disable active calls by waiting for the active services on the specified Service Processing Elements (SPEs) to terminate, use the busyout SPE configuration command. To re-enable the SPEs, use the no form of this command.
busyout
no busyout
Syntax Description
This command has no arguments or keywords.
Defaults
no busyout
Command Modes
SPE configuration
Command History
Usage Guidelines
You can perform autodiagnostic tests and firmware upgrades when you put the SPEs in the OutofService state. Active ports on the specified SPE will change the state of the specified range of SPEs to the busyout pending state. The state changes from busyout pending to OutofService when all calls end. Use the show spe command to see the state of the range of SPEs. Use the shutdown command to override the busyout command. Use the no busyout command to reenable the SPEs.
Examples
The example below will show all active ports on SPE 1 to 10 on slot 1being busied out:
router(config)# SPE 1/1 1/10router(config-SPE)# busyoutrouter(Config-port)#Related Commands
clear port
To reset the NextPort port and clear any active call to the port, use the clear port EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
clear port [slot | slot/port]
Cisco AS5800 with Universal Port DFC
clear port [shelf/slot | shelf/slot/port]
Syntax Description
slot/port
(Optional) The specified SPE slot/port range.
slot
(Optional) The specified SPE slot.
shelf/slot/port
(Optional) The specified port range on a shelf and slot.
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
If you specify the shelf, slot, and port, you clear that port on that Service Processing Element (SPE). If you specify only the shelf and slot, you clear all active ports on that particular shelf and slot. If you do not specify a shelf, slot, or port, you clear all the ports on the universal gateway.
The clear port log clears the entire port log. You cannot remove individual service events from the port log. On the Cisco AS5400 only, you can use show port modem log or show port digital log or both to display specific service events, but you must use clear port log to clear the entire port event log.
Additionally, this command clears the Bad state on a port and resets it. However, the port is not cleared if the SPE was previously in a Bad state due to an SPE firmware download.
Examples
The following example shows output from the clear port command on the Cisco AS5350 with NextPort DFC. This example clears slot 1, port 1:
Router# clear port 1/1Router#The following example shows output from the clear port command on the Cisco AS5800 with NextPort DFC. This example clears shelf 1, slot 3,port 0:
Router# clear port 01/03/00This will clear port 1/03/00[confirm]yRelated Commands
clear spe
To reboot all specified Service Processing Elements (SPE), use the clear spe EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
clear port log [slot | slot/port]
no clear spe [slot | slot/spe]
Cisco AS5800 with Universal Port DFC
clear port log [shelf/slot | shelf/slot/spe]
Syntax Description
Defaults
Disabled
Command Modes
EXEC
Command History
Usage Guidelines
Execution of this command causes the configured firmware to be downloaded to the specified SPE or the range of SPEs and power-on self-test (POST) to be executed. This command can be issued regardless of the state of the SPEs.
Caution
This command downloads configured SPEs with firmware as configured. Unconfigured SPEs are downloaded with the default firmware, which is the bundled version. To configure and manage the downloading of firmware without abruptly terminating SPEs, use the firmware location or firmware upgrade commands as appropriate.
Examples
The following example shows output from the clear spe command on the Cisco AS5350 with NextPort DFC. This example performs a cold start on slot 1, SPE 1:
Router# clear spe 1/1Router# Are you sure you want to clear spe 1/1(Y/N)? yThe following example displays the prompt when the clear spe command is entered on the Cisco AS5800 with Universal Port DFC. The command prompts the system to perform a cold start on shelf 1, slot 8, SPE 0:
Router# clear spe 1/8/0Router# Are you sure you want to clear spe 1/8(Y/N)? yRelated Commands
clear spe counters
To clear all statistics, use the clear spe counters EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
clear spe counters [slot | slot/spe]
Cisco AS5800 with Universal Port DFC
clear spe counters [shelf/slot | shelf/slot/spe]
Syntax Description
Defaults
Disabled
Command Modes
EXEC
Command History
Usage Guidelines
This command clears statistical counters of all service types for the specified SPE, the specified range of SPEs, or all SPEs. If no parameter is specified, all SPE statistical counters are cleared.
Examples
The following example shows how to clear all statistics by entering the clear spe counters command on the Cisco AS5350 with NextPort DFC.
Router# clear spe counters 01/3 01/7This will clear statistic counters for SPEs 1/03 - 1/07 [confirm]yThe following example shows how to clear all statistics by entering the clear spe counters command on the Cisco AS5800 with Universal Port DFC. This example clears shelf 1, slot 3, ports 0 to 11.
Router# clear spe counters 01/03/00 01/03/11This will clear statistic counters for SPEs 1/03/00 - 1/03/11[confirm]yclear spe log
To clear event entries in the slot history event log, use the clear spe log EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
clear spe log [slot]
Cisco AS5800 with Universal Port DFC
clear spe log [shelf/slot]
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
The clear spe log command clears event entries in the slot history event log. If you do not specify the shelf/slot range, all Service Processing Element (SPE) event entries clear. If you specify the shelf/slot, only the event entries for that slot clear.
Examples
The following example shows output from the clear spe log command on the Cisco AS5350 with
NextPort DFC. This example clears the SPE log on slot 3:
Router# clear spe log 1/03This will clear slot event history for slot(s) 3 - 3[confirm]yThe following example shows output from the clear spe log command on the Cisco AS5800 with Universal Port DFC. This example clears shelf 1, slot 8, SPE 0:
Router# clear spe log 1/8/0This will clear slot event history for slot(s) 8 - 8[confirm]yRelated Commands
firmware location
To specify a firmware file to upgrade, use the firmware location SPE configuration command.
firmware location filename
Syntax Description
Defaults
No default behavior or values.
Command Modes
SPE configuration
Command History
12.0(4)XI1
This command was introduced.
12.0(6)T
This command was integrated into Release 12.0(6)T on the Cisco AS5300 and the Cisco AS5800 for MICA modems. For information on the use of this command in Cisco IOS releases for those platforms, see Cisco IOS Dial Services Command Reference, Cisco IOS Release 12.1.
12.1(1)XD
This command was introduced on the Cisco AS5400.
12.1(3)T
This command was integrated into Cisco IOS Release 12.1(3)T on the Cisco AS5400 and the Cisco AS5800.
12.1(5)XM1
This command was introduced on the Cisco AS5350 universal gateway.
12.2(11)T
This command was integrated into Cisco IOS Release 12.2(11)T and support was added for the Cisco AS5350.
Usage Guidelines
The new SPE firmware image can usually be retrieved from Cisco.com. The user must first copy the SPE image from a tftp server to Flash memory using the copy tftp flash command.
This command specifies the location of the firmware file and downloads the firmware in the range of SPEs specified, depending on the states configured by the firmware upgrade command. Use the firmware location command in conjunction with the firmware upgrade command. The entire SPE is necessarily affected by the firmware location command.
The copy modem flash command is replaced by these commands.
This command cannot be performed on the SPEs that are in the Bad state.
Note
Examples
The following example sets the SPEs, specifies the firmware file location, opens the file (if on Flash memory), and downloads to the SPE on the Cisco AS5350:
router(config)# spe 1/0 1/54router(config-spe)# firmware location np-spe-upw-1.0.1.2.binrouter(config-spe)# endThe following example shows how to enter the configuration mode, set the range of SPEs, specifies the firmware file location in Flash memory, downloads the file to the SPEs, and report on the status, using the show spe command:
router# config trouter(config)# spe 7/0 7/17router(config-spe)# firmware location flash:np_6_75Started downloading firmware flash:np_6_75.sperouter(config-spe)#router# show spe 7...SPE SPE SPE SPE Port CallSPE# Port # State Busyout Shut Crash State Type7/00 0000-0005 ACTIVE 1 0 0 BBBBBB ______7/01 0006-0011 DOWNLOAD 1 0 0 bbbbbb ______7/02 0012-0017 DOWNLOAD 1 0 0 bbbbbb ______7/03 0018-0023 DOWNLOAD 1 0 0 bbbbbb ______...Related Commands
firmware upgrade
To specify an SPE firmware upgrade method, use the firmware upgrade SPE configuration command.
firmware upgrade [busyout | download-maintenance | reboot]
Syntax Description
busyout
Upgrade when all calls are terminated on the SPE.
download-maintenance
Upgrade during download maintenance time.
reboot
Upgrades at the next reboot.
Defaults
No default behavior or values.
Command Modes
SPE configuration
Command History
Usage Guidelines
Three methods of upgrade are available: busyout, reboot, and download-maintenance.
Reboot requests the Cisco AS5350 to upgrade SPE firmware at the next reboot. Busyout waits until all calls are terminated on an SPE before SPE firmware is upgraded. Download-maintenance requests SPE firmware download during maintenance time. See the spe download maintenance command.
Use this command in conjunction with the firmware location command and the spe download maintenance command.
The SPE firmware location command is designed to integrate all continuous ranges of SPEs containing the same firmware location. However, the firmware upgrade command does not affect the ranges of SPEs. As such, all SPEs within the ranges of SPEs must have the same firmware upgrade mode or the router uses busyout, one of the upgrade modes. If you want to upgrade a single SPE within an existing range of SPEs with a different upgrade mode than is currently configured, you must first change the upgrade mode for the entire range of SPEs and then change the firmware location for the specific SPE being upgraded.
Furthermore, each time you merge ranges of SPEs due to configuration changes, verify the configuration of the SPE firmware upgrade.
Examples
The following example shows how to set the range of SPEs, and specify the firmware upgrade to take place when all calls are terminated on the SPE:
router(config)# spe 5/4 5/6router(config-spe)# firmware ?location Firmware file locationupgrade Firmware upgrade configurationrouter(config-spe)# firmware upgrade busyoutrouter(config-spe)#If the busyout upgrade command is specified, or if no upgrade mode is specified, the SPE modems are set into a pending download state when you use the firmware location command on the specified SPE. The pending download state prevents any modem in that state to be allocated for new calls until the state is cleared. Modems with active calls remain active for their call durations, but enter the pending download state when they finish. This pending download state can be cleared only when the SPE is finally downloaded. When all modems within the SPE are in the pending download state and no active calls remain on the SPE, the SPE is reloaded. The busyout command is the fastest way to upgrade modems on an active router but can severely impact the capacity of the router during the upgrade. This is the default option for the firmware upgrade command:
router(config-spe)# firmware upgrade busyoutIf reboot upgrade is specified, the SPE modems are not reloaded to the new firmware location until the router is rebooted. The reboot upgrade option is useful for routers that need to have their SPE upgraded and are going to be rebooted for maintenance. The new firmware can be configured, but does not take affect until the reboot takes place:
router(config-spe)# firmware upgrade rebootIf recovery upgrade is specified, the SPE modems are reloaded based on the modem recovery algorithm. The SPE modems are all set into a pending upgrade state when you use the firmware location command on this SPE. The pending upgrade state continues to allow calls to be allocated to modems for as long as there are active calls on the SPE. Only when no active calls exist on the SPE does the firmware download take place. Furthermore, at the configured modem recovery maintenance time (3:00 a.m.), the modem recovery maintenance process, in a controller fashion, attempts to reload the modems by busying out the modems for a period of time to allow the download to take place. Consult the modem recovery documentation for further details. The recovery upgrade option is the least impacting way to upgrade modems on an active router. Capacity is kept at a maximum. However, this option may take a few days to load all modems to the new firmware location:
router(config-spe)# firmware upgrade recoveryRelated Commands
port modem autotest
To automatically and periodically perform a modem diagnostics test for modems inside the universal gateway or router, use the port modem autotest command in global configuration mode. To disable or turn off the modem autotest service use the no form of this command.
port modem autotest {error threshold | minimum modem | time hh:mm [interval]}
no port modem autotest
Syntax Description
Defaults
Modem diagnostics test are disabled.
Command Modes
Global configuration
Command History
Examples
The following example shows how to set the modem autotest to run once per week at 3:00 a.m. In addition, the autotest will activates if the system detects a modem error count higher than 40 errors.
Determine the current time set on the access server with the show clock EXEC command. In this example, the time and date set is 3:00 p.m, Monday, August 25, 1997:
Router# show clock*15:00:01.031 EST Aug 25 1997Enter global configuration mode and set the time you want the modem autotest to activate. In this example, the access server is configured to run the modem autotest each ongoing Tuesday at 3:00 a.m:
Router# configure terminalEnter configuration commands, one per line. End with CNTL/Z.
Router(config)# port modem autotest time 03:00 168Configure the autotest to activate if the system detects a high modem error count. In this example, the autotest activates if the system detects a modem error count higher than 40 errors. For the list of modem errors that are monitored by the modem autotest command, see the show modem call-stats command.
Router(config)# port modem autotest error 40Router(config)# exitRelated Commands
show port config
To display the active session's configuration parameters, use the show port config EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show port config {slot/port [slot/port]}
Cisco AS5800 with Universal Port Card
show port config {shelf/slot | shelf/slot/port}
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
The port should have an associated active session when the show port config command is executed. The show port config command is equivalent to the show modem config MICA modem command.
Examples
The example below shows output from the show port config command on the Cisco AS5350 with NextPort DFC. This example shows port configuration for the modem service port slot 2, shelf 1:
router# show port config 2/1Slot/SPE/Port -- 2/0/1Service Type :Modem serviceOriginate/Answer Mode :AnswerData Bits Selection :8Parity Selection :No ParityStop bits Selection :1V.42 ODP generation :EnabledEC Autodetect Time-out :5000 msProtocol Negotiation Time-out :10000 msProtocol Negotiation Fallback character :13Protocol Negotiation Retransmission Limit :12EC Min, Max Octets Frame length :256Data Compression :V.42bis or MNP5ARA Error Correction :ARA1.0 & ARA2.0 DisabledV.42 Error Correction :V.42(LAP-M) Originate&Answer enabledMNP Error Correction :MNP Originate&Answer enabledLink Protocol Fallback :Async Framing (Start/Stop/Parity)Calling Tone :DisabledGuard Tone :DisabledModem Standard :V.90 AutomodeMax Non-PCM Connect Rate :33600 bpsMin Non-PCM Connect Rate :300 bpsMax PCM Connect Rate :60000 bpsMin PCM Connect Rate :28000 bpsSignal Quality Threshold :Bit Errors >= 1:1000 cause recoveryFallback/Fallforward Squelch Timer :500 msFall Forward Timer :10000 msFall Back Timer :500 msTerminate Time-out :20 secsWait for Data Mode Time-out :60 secsLost Carrier To Hang-up Delay :1400 msPCM Transmit Level Setting :-13 dBmRetrain Limit :4V.34 Max Symbol Rate :3429 BaudV.34 Min Symbol Rate :2400 BaudV.34 Carrier Frequency :Auto Carrier SelectionV.34 Preemphasis Filter Selection :11+++ Escape Detection :Enabled-in-Originate-Mode-OnlyAT Command Processor :EnabledCall Setup Delay :0 msAutomatic Answer Delay :2 secsEscape Detection Character :ASCII 43 (+)Carriage Return Character :ASCII 13 (CR)Line Feed Character :ASCII 10 (LF)Backspace Character :ASCII 8 (BS)Pause Before Blind Dialing :2 secsComma Dial Modifier Time :2 secsThe example below shows port configuration information for a digital service port slot 2, port 23 on the Cisco AS5350 with NextPort DFC.
router# sh port conf 2/23Slot/SPE/Port -- 2/3/23Service Type : Digital serviceOriginate/Answer Mode : AnswerData Bits Selection : 8Parity Selection : No ParityStop bits Selection : 1Modem Standard : reservedUser Rate for ISDN : 19200 bpsThe following example shows port configuration information for a digital service port slot 2, port 23 on the Cisco AS5800 with Universal Port Card.
Router# show port config 1/8Shelf/Slot/SPE/Port -- 1/8/27/165Service Type : Modem serviceOriginate/Answer Mode : AnswerData Bits Selection : 8Parity Selection : No ParityStop bits Selection : 1V.42 ODP generation : EnabledEC Autodetect Time-out : 5000 msProtocol Negotiation Time-out : 10000 msProtocol Negotiation Fallback character : 13Protocol Negotiation Retransmission Limit : 12EC Min, Max Octets Frame length : 256Data Compression : V.42bis or MNP5ARA Error Correction : ARA1.0 & ARA2.0 DisabledV.42 Error Correction : V.42(LAP-M) Originate&Answer enabledMNP Error Correction : MNP Originate&Answer enabledLink Protocol Fallback : Async Framing (Start/Stop/Parity)Calling Tone : DisabledGuard Tone : DisabledModem Standard : V.90 AutomodeMax Non-PCM Connect Rate : 33600 bpsMin Non-PCM Connect Rate : 300 bpsMax PCM Connect Rate : 60000 bps...Related Commands
show port digital log
To display the digital data event log, use the show port log EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show port digital log [reverse] [slot/port [slot/port]]
Note
Syntax Description
Command Modes
EXEC
Command History
Examples
The example below shows output from the show port digital log on the Cisco AS5400 with NextPort DFC:
Router# show port digital logPort 5/00 Events Log00:02:41: incoming called number: 35140Service type: DIGITAL_DATASession State: IDLEService type: DIGITAL_DATASession State: ACTIVE00:02:41: Digital State event:State: Steady00:02:40: Digital Static event:Connect Protocol : V.110Data Bits : 8Parity : 0Stop Bits : 1TX,RX Bit Rate : 19200, 19200Port 5/01 Events Log00:02:42: incoming called number: 35140Service type: DIGITAL_DATASession State: IDLEService type: DIGITAL_DATASession State: ACTIVE00:02:41: Digital State event:State: Steady00:02:41: Digital Static event:Connect Protocol : V.110Data Bits : 8Parity : 0Stop Bits : 1TX,RX Bit Rate : 19200, 19200Port 5/02 Events Log00:02:42: incoming called number: 35140Service type: DIGITAL_DATASession State: IDLEService type: DIGITAL_DATASession State: ACTIVE00:02:42: Digital State event:State: Steady00:02:42: Digital Static event:Connect Protocol : V.110Data Bits : 8Parity : 0Stop Bits : 1TX,RX Bit Rate : 19200, 19200Port 5/03 Events Log00:02:43: incoming called number: 35140Service type: DIGITAL_DATASession State: IDLEService type: DIGITAL_DATASession State: ACTIVE00:02:43: Digital State event:State: Steady00:02:43: Digital Static event:Connect Protocol : V.110Data Bits : 8Parity : 0...Related Commands
show port modem calltracker
To display the port level information for an active modem, use the show port modem calltracker EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show port modem calltracker [slot | slot/port]
Cisco AS5800 with Universal Port DFC
show port modem calltracker [shelf/slot | shelf/slot/port]
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
When there is no call on the specified port, the most recent call information is displayed. This command uses the calltracker database. To enablecalltracker, enter the calltracker enable global configuration command.
Examples
The following example shows output from the show port modem calltracker command on the Cisco AS5400 with NextPort DFC. This example shows output for slot 3, port 3.
Router# show port modem calltracker 3/3-------------------------- call handle= 62 --------------------------status=Active, service=PPP, origin=Answer, category=ModemDS0 slot/port/ds1/chan=4/7/7/0, called=124, calling=(n/a)userid=as5300-ref2, ip=192.169.124.1, mask=255.255.255.0setup=06/22/2000 21:50:47, conn=6.77, phys=25.00, service=29.83, authen=29.83init rx/tx b-rate=33600/33600, rx/tx chars=0/0resource slot/port=3/3, mp bundle=0, charged units=0, account id=0idb handle=0x645B97CC, tty handle=0x622207BC, tcb handle=0x0----------------------------------------------------------------------------protocol: last=LAP-M, attempted=LAP-Mcompression: last=V.42bis-Both, supported= V.42bis-RX V.42bis-TXstandard: last=V.34+, attempted=V.21, initial=V.21snr=40 dB, sq=5, rx/tx level=-15/0 dBmphase jitter: freq=1 Hz, level=2 degreesfar end echo level=-90 dBm, freq offset=0 Hzphase roll=0 degrees, round-trip delay=0 msecsdigital pad=None dB, digital pad comp=0rbs pattern=0, constellation=0 pointrx/tx: symbol rate=3429/3429, carrier freq=1959/1959rx/tx: trellis code=0/0, preemphasis index=0/0rx/tx: constellation shape=Off/Off, nonlinear encode=Off/Offrx/tx: precode=Off/Off, xmit level reduct=0/0 dBmrx/tx: chars=0/0, general info=0x0rx/tx: link layer chars=0/0, NAKs=0/0error corrected: rx/tx=0/0, rx bad=0ec retransmissions=0, retransmitted frames=0rx/tx ppp slip=0/0, bad ppp slip=0rx/tx b-rate: last=33600/33600, lowest=0/0, highest=0/0phase 2 projected max rx b-rate: client=0, host=33600phase 4 desired rx/tx b-rate: client=16384/25987, host=25987/42765retrains: local=0, remote=0, failed=0speedshift: local up/down=0/0, remote up/down=0/0, failed=0v110: rx good=0, rx bad=0, tx=0, sync lost=0SS7/COT status=0x00v90: status=(Invalid #141), client=(n/a), failure=Nonerx/tx: max neg I frame=128/128, neg window=0/128v42bis size: dictionary=0, string=16T401 timeouts=0, tx window closures=0, rx overruns=0test err=0, reset=0, v0 synch loss=0mail lost: host=0, sp=0duration(sec)=0, disc reason=0x0disc text=(n/a)--------5---------10--------15--------20--------25--------30line shape : 0x0000000000000000000000000000000000000000000000000000v8bis capab : 0x12C9808081C609B502009481834347CB000000000000v8bis mod sl: 0x00000000000000000000000000000000000000000000v8 jnt menu : 0xC16513942A8D00000000000000000000000000000000v8 call menu: 0x00C16513942A00000000000000000000000000000000v90 training: 0x00000000v90 sgn ptrn: 0x00000000state trnsn : 0x0F0F010203041013151920FF0000000000000000000000000000000000000000portwre diag: 0x00000000000000000000000000000000phase 2 info: 0x0200EFF41F120000003CEFF41F0200E001EFB4014082050B0834702000011EEFB41440E1050008FCA707A707650D00000000000000000000phase 4 info: 0x0DA70D65836583400040----------------------------------------------------------------------------show port modem log
To display the events generated by the modem sessions, use the show port modem log EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show port modem log [reverse slot/port] [slot | slot/port]
Cisco AS5800 with Universal Port Card DFC
show port modem log [reverse shelf/slot/port] [shelf/slot | shelf/slot/port]
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
The port modem test log displays the results of the SPE diagnostics tests.
Examples
The following example shows output for the Cisco AS5400 with NextPort DFC. This example shows the port history event log for slot 5, port 47:
Router# show port modem log 5/47Port 5/47 Events LogService type: DATA_FAX_MODEMService mode: DATA_FAX_MODEMSession State: IDLE00:02:23: incoming called number: 35160Service type: DATA_FAX_MODEMService mode: DATA_FAX_MODEMSession State: IDLEService type: DATA_FAX_MODEMService mode: DATA_FAX_MODEMSession State: ACTIVE00:02:23: Modem State event:State: Connect00:02:16: Modem State event:State: Link00:02:13: Modem State event:State: Train Up00:02:05: Modem State event:State: EC Negotiating00:02:05: Modem State event:State: Steady00:02:05: Modem Static event:Connect Protocol : LAP-MCompression : V.42bisConnected Standard : V.34+TX,RX Symbol Rate : 3429, 3429TX,RX Carrier Frequency : 1959, 1959TX,RX Trellis Coding : 16/16Frequency Offset : 0 HzRound Trip Delay : 0 msecsTX,RX Bit Rate : 33600, 33600Robbed Bit Signalling (RBS) pattern : 0Digital Pad : NoneDigital Pad Compensation : None4 bytes of link info not formatted : 0x00 0x00 0x00 0x00 0x0000:02:06:Modem Dynamic event:Sq Value : 5Signal Noise Ratio : 40 dBReceive Level : -12 dBmPhase Jitter Frequency : 0 HzPhase Jitter Level : 2 degreesFar End Echo Level : -90 dBmPhase Roll : 0 degreesTotal Retrains : 0EC Retransmission Count : 0Characters transmitted, received : 0, 0Characters received BAD : 0PPP/SLIP packets transmitted, received : 0, 0PPP/SLIP packets received (BAD/ABORTED) : 0EC packets transmitted, received OK : 0, 0EC packets (Received BAD/ABORTED) : 0This following example shows the port history event log with the most recent event first on slot 5, port 40:
Router# show port modem log reverse 5/40Modem port 5/40 Events Log00:02:18:Modem Dynamic event:Sq Value : 5Signal Noise Ratio : 38 dBReceive Level : -12 dBmPhase Jitter Frequency : 0 HzPhase Jitter Level : 0 degreesFar End Echo Level : 0 dBmPhase Roll : 0 degreesTotal Retrains : 0EC Retransmission Count : 0Characters transmitted, received : 0, 0Characters received BAD : 0PPP/SLIP packets transmitted, received : 0, 0PPP/SLIP packets received (BAD/ABORTED) : 0EC packets transmitted, received OK : 0, 0EC packets (Received BAD/ABORTED) : 000:02:18: Modem Static event:Connect Protocol : LAP-MCompression : V.42bisConnected Standard : V.90TX,RX Symbol Rate : 8000, 3200TX,RX Carrier Frequency : 1829, 1829TX,RX Trellis Coding : 16/16Frequency Offset : 0 HzRound Trip Delay : 4 msecsTX,RX Bit Rate : 52000, 28800Robbed Bit Signalling (RBS) pattern : 255Digital Pad : NoneDigital Pad Compensation : Enabled4 bytes of link info not formatted : 0x00 0x00 0x00 0x00 0x0000:02:23: Modem State event:State: Steady00:02:23: Modem State event:State: EC Negotiating00:02:36: Modem State event:State: Train Up00:02:39: Modem State event:State: Link00:02:46: Modem State event:State: Connect00:02:46: Port State Reached:Service type: DATA_FAX_MODEMService mode: DATA_FAX_MODEMSession State: ACTIVE00:02:46: Port State Reached:Service type: DATA_FAX_MODEMService mode: DATA_FAX_MODEMSession State: IDLE00:02:47: incoming called number: 600000:02:47: incoming caller number: 90002The following example shows output for the Cisco AS5800 with Universal Port DFC. This example shows the port history event log for slot 8, ports 0 to 6:
Router# show port modem log 1/8/0 1/8/6Port 1/08/00 Events Log09:09:53: Service Type: DATA_FAX_MODEM09:09:53: Service Mode: DATA_FAX_MODEM09:09:53: Session State: FLUSHING09:09:53: Service Type: DATA_FAX_MODEM09:09:53: Service Mode: DATA_FAX_MODEM09:09:53: Session State: IDLE09:09:53: Modem State event:State: Terminate09:09:53: Modem End Connect event:Call Timer : 26 secsDisconnect Reason Info : 0x1F00Type (=0 ): <unknown>Class (=31 ): Requested by hostReason (=0 ): non-specific host disconnectTotal Retrains : 0EC Retransmission Count : 0Characters transmitted, received : 2633, 485Characters received BAD : 0PPP/SLIP packets transmitted, received : 0, 0PPP/SLIP packets received (BAD/ABORTED) : 0EC packets transmitted, received OK : 27, 21EC packets (Received BAD/ABORTED) : 009:09:54:Modem Link Rate event:09:09:55: Service Type: DATA_FAX_MODEM09:09:55: Service Mode: DATA_FAX_MODEM09:09:55: Session State: IDLE09:09:55: Service Type: DATA_FAX_MODEM09:09:55: Service Mode: DATA_FAX_MODEM09:09:55: Session State: ACTIVE09:09:55: Modem State event:State: Connect09:09:55: Modem State event:State: Link09:09:55: Modem State event:State: Train Up09:09:55: Modem State event:State: EC Negotiating09:09:55: Modem State event:State: Steady09:09:55: Modem Static event:Connect Protocol : LAP-MCompression : V.42bisConnected Standard : V.34+TX,RX Symbol Rate : 3429, 3429TX,RX Carrier Frequency : 1959, 1959TX,RX Trellis Coding : 16/16Frequency Offset : 0 HzRound Trip Delay : 1 msecsTX,RX Bit Rate : 31200, 28800Robbed Bit Signalling (RBS) pattern : 0Digital Pad : NoneDigital Pad Compensation : None4 bytes of link info not formatted : 0x00 0x00 0x00 0x00 0x0009:09:56: Modem Dynamic event:Sq Value : 5Signal Noise Ratio : 38 dBReceive Level : -15 dBmPhase Jitter Frequency : 13 HzPhase Jitter Level : 0 degreesFar End Echo Level : -90 dBmPhase Roll : 0 degreesTotal Retrains : 0EC Retransmission Count : 0Characters transmitted, received : 0, 0Characters received BAD : 0PPP/SLIP packets transmitted, received : 0, 0PPP/SLIP packets received (BAD/ABORTED) : 0EC packets transmitted, received OK : 0, 0EC packets (Received BAD/ABORTED) : 009:09:58: Service Type: DATA_FAX_MODEM09:09:58: Service Mode: DATA_FAX_MODEM09:09:58: Session State: FLUSHING09:09:58: Service Type: DATA_FAX_MODEM09:09:58: Service Mode: DATA_FAX_MODEM09:09:58: Session State: IDLE09:09:58: Modem State event:State: Terminate...Related Commands
show port modem test
To display the modem port test log, use the show port modem test EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show port modem test [slot | slot/port]
Cisco AS5800 with Universal Port Card DFC
show port modem test [shelf/slot | shelf/slot/port]
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
The port modem test log displays the results of the SPE diagnostics tests.
Examples
The following example shows output for the Cisco AS5400 with NextPort DFC. This example displays the results of the SPE startup test, SPE auto-test, and SPE back-to-back test.
Note
router# show port modem testDate Time Modem Test Reason State Result3/02 12:00:57 PM 2/01 Back-To-Back :STARTUP TEST Idle PASS3/02 12:00:57 PM 2/00 Back-To-Back :STARTUP TEST Idle PASS3/02 12:00:58 PM 2/02 Back-To-Back :STARTUP TEST Idle PASS3/02 12:00:58 PM 2/03 Back-To-Back :STARTUP TEST Idle PASS3/02 12:00:58 PM 2/04 Back-To-Back :STARTUP TEST Idle PASS3/02 12:00:58 PM 2/05 Back-To-Back :STARTUP TEST Idle PASS...3/02 12:01:14 PM 3/95 Back-To-Back :STARTUP TEST Idle PASS3/02 12:01:14 PM 3/94 Back-To-Back :STARTUP TEST Idle PASS3/02 12:01:15 PM 3/75 Back-To-Back :STARTUP TEST Idle PASS3/02 12:01:15 PM 3/74 Back-To-Back :STARTUP TEST Idle PASS3/02 12:13:52 PM 3/20 Back-To-Back :USER INITIATED Idle PASS3/02 12:13:52 PM 2/10 Back-To-Back :USER INITIATED Idle PASS...3/02 12:44:00 PM 3/102 No Test (Time) :MIN IDLE MODEMS Idle NOTST3/02 12:44:00 PM 3/103 No Test (Time) :MIN IDLE MODEMS Idle NOTST3/02 12:44:00 PM 3/104 No Test (Time) :MIN IDLE MODEMS Idle NOTST3/02 12:44:00 PM 3/105 No Test (Time) :MIN IDLE MODEMS Idle NOTST3/02 12:44:00 PM 3/106 No Test (Time) :MIN IDLE MODEMS Idle NOTST3/02 12:44:00 PM 3/107 No Test (Time) :MIN IDLE MODEMS Idle NOTST3/02 12:44:21 PM 2/73 Back-To-Back :TIME INTERVAL Idle PASS3/02 12:44:21 PM 2/72 Back-To-Back :TIME INTERVAL Idle PASS3/02 12:44:21 PM 2/33 Back-To-Back :TIME INTERVAL Idle PASS3/02 12:44:21 PM 2/32 Back-To-Back :TIME INTERVAL Idle PASS3/02 12:44:21 PM 3/37 Back-To-Back :TIME INTERVAL Idle PASSRelated Commands
show port operational-status
To display the active session's statistics, use the show port operational-status EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show port operational-status {slot | slot/port}
Cisco AS5800 with Universal Port Card DFC
show port operational-status {shelf/slot | shelf/slot/port}
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
This command displays the operational status of a specific port or range of ports. The port should have an associated active modem session when command is executed. The show port operational-status command is equivalent to the show modem operational-status MICA modem command.
Examples
The following example shows output from the show port operational-status command on the Cisco AS5400 with NextPort DFC. This example displays operational status for slot 2, SPE 0, port 1:
router# show port operational-status 2/1Slot/SPE/Port -- 2/0/1Service Type :Modem serviceDisconnect Reason Info :0x0Type (=0 ): <unknown>Class (=0 ): OtherReason (=0 ): no disconnect has yet occurredModulation Standard :V.34+TX/RX Bit Rate :31200/14400Connect Protocol :LAP-MCompression :V.42bisCall Timer :47 secsLink Signal Quality :7SNR :37 dBTX/RX Symbol Rate :3429/3429TX/RX Carrier Frequency :1959/1959TX/RX Trellis Coding :16/16TX/RX Preemphasis Index :0/1TX/RX Constellation Shaping :On-Active/On-ActiveTX/RX Nonlinear Encoding :On-Active/On-ActiveTX/RX Precoding :On-Active/On-ActiveTX/RX Xmit Level Reduction :3/1 dBmReceive Level :-15 dBmFrequency Offset :0 HzPhase Jitter Frequency :2 HzPhase Jitter Level :2 degreesFar End Echo Level :-90 dBmPhase Roll :0 degreesRound Trip Delay :0 msecs>Total Retrains :0Self Test Error count :0EC Retransmission count :0EC packets transmitted/received OK :11/12EC packets (Received BAD/ABORTED) :0Characters transmitted/received :76/13Characters received BAD :0PPP/SLIP packets transmitted/received :0/0PPP/SLIP packets received (BAD/ABORTED) :0RBS Pattern :0Digital Pad :0Digital Pad Compensation :0The following example displays operational status for a V.110 digital service slot/port.
router# show port operational-status 2/23Slot/SPE/Port -- 2/3/23Service Type : Digital serviceConnect Protocol : V110Data Bits : 8Parity : 0Stop Bits : 1TX/RX Bit Rate : 19200/19200Call Timer : 116 secsEC packets transmitted/received OK : 0/0EC packets (Received BAD/ABORTED) : 0PPP/SLIP packets transmitted, received : 8/8PPP/SLIP packets received (BAD/ABORTED) : 0Sync Loss : 0The example below displays show port operational status for a modem service port located in Slot/SPE/Port: 2/0/0.
show port op 2/00Slot/SPE/Port -- 2/0/0Service Type : Modem serviceDisconnect Reason Info : 0x0Type (=0 ): <unknown>Class (=0 ): OtherReason (=0 ): no disconnect has yet occurredModulation Standard : V.34+TX/RX Bit Rate : 31200/33600Connect Protocol : LAP-MCompression : V.42bisCall Timer : 34 secsLink Signal Quality : 6SNR : 40 dBTX/RX Symbol Rate : 3429/3429TX/RX Carrier Frequency : 1959/1959TX/RX Trellis Coding : 16/16TX/RX Preemphasis Index : 0/0TX/RX Constellation Shaping : Off-None/On-ActiveTX/RX Nonlinear Encoding : Off-None/On-ActiveTX/RX Precoding : Off-None/On-ActiveTX/RX Xmit Level Reduction : 6/4 dBmReceive Level : -13 dBmFrequency Offset : 0 HzPhase Jitter Frequency : 2 HzPhase Jitter Level : 0 degreesFar End Echo Level : -90 dBmPhase Roll : 0 degreesRound Trip Delay : 0 msecsTotal Retrains : 0Self Test Error count : 0EC Retransmission count : 0EC packets transmitted/received OK : 1/1EC packets (Received BAD/ABORTED) : 0Characters transmitted/received : 7/1Characters received BAD : 0PPP/SLIP packets transmitted/received : 0/0PPP/SLIP packets received (BAD/ABORTED) : 0RBS Pattern : 0Digital Pad : 0Digital Pad Compensation : 0See Table 11 for field definitions for output display of the modem operational-status command.
Related Commands
s
show spe
To show Service Processing Element (SPE) status, use the show spe EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe [slot | slot/spe]
Cisco AS5800 with Universal Port Card DFC
show spe [shelf/slot | shelf/slot/spe]
Syntax Descriptions
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
Use the show spe command to display status and history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Examples
The following example displays history statistics for all SPEs after a busyout was executed on SPE 2/0 and a shutdown was executed on SPE 2/1:
router# show speSPE settings:==============Country code configuration: default T1 (u Law)Polling interval: 12 secs.History log events: 50(per port)Port legends:============Port state: (s)shutdown (t)test (r)recovery (d)download(b)busiedout (p)busyout pending, (B)bad (a)active callCall Type: (m)modem (d)digital (_)not in useSPE SPE SPE SPE Port CallSPE# Port # State Busyout Shut Crash State Type2/00 0000-0005 ACTIVE 0 0 0 aaaaaa dddddd2/01 0006-0011 ACTIVE 0 0 0 aaaaaa dddddd2/02 0012-0017 ACTIVE 0 0 0 aaaaaa dddddd2/03 0018-0023 ACTIVE 0 0 0 aaaaaa dddmdm2/04 0024-0029 ACTIVE 0 0 0 aaaaaa dmmmmm2/05 0030-0035 ACTIVE 0 0 0 aaa_aa mmm_mm2/06 0036-0041 ACTIVE 0 0 0 __aaaa __mmmm2/07 0042-0047 ACTIVE 0 0 0 aaa_aa mmm_mm2/08 0048-0053 ACTIVE 0 0 0 _aaa_a _mmm_m2/09 0054-0059 ACTIVE 0 0 0 _aa_aa _md_mm2/10 0060-0065 ACTIVE 0 0 0 _a_a_a _m_m_m2/11 0066-0071 ACTIVE 0 0 0 _a_aaa _d_mmd2/12 0072-0077 ACTIVE 0 0 0 aaaaaa mdmmmd2/13 0078-0083 ACTIVE 0 0 0 _aaaaa _dmmdm2/14 0084-0089 ACTIVE 0 0 0 _a_aaa _m_ddd2/15 0090-0095 ACTIVE 0 0 0 a_aaaa m_dddd2/16 0096-0101 ACTIVE 0 0 0 aaaaaa ddddmd2/17 0102-0107 ACTIVE 0 0 0 aaaaaa ddddddThe following example shows output for the show spe command on the Cisco AS5800 with one Universal Port DFC:
Router# show speSPE settings==============Country code configuration default T1 (u Law)Polling interval 12 secs.History log events 50(per port)Port legends============Port state (s)shutdown (t)test (r)recovery (d)download(b)busiedout (p)busyout pending, (B)bad (a)active callCall type (m)modem (d)digital (_)not in useSPE SPE SPE SPE Port CallSPE# Port # State Busyout Shut Crash State Type1/02/00 0000-0005 ACTIVE 0 0 0 a_a_a_ m_m_m_1/02/01 0006-0011 ACTIVE 0 0 0 aaa___ mmm___1/02/02 0012-0017 ACTIVE 0 0 0 _a_aa_ _m_mm_1/02/03 0018-0023 ACTIVE 0 0 0 _aaaaa _mmmmm1/02/04 0024-0029 ACTIVE 0 0 0 a_a_a_ m_m_m_1/02/05 0030-0035 ACTIVE 0 0 0 ____a_ ____m_1/02/06 0036-0041 ACTIVE 0 0 0 _aaa_a _mmm_m1/02/07 0042-0047 ACTIVE 0 0 0 a_____ m_____1/02/08 0048-0053 ACTIVE 0 0 0 _aa_aa _mm_mm1/02/09 0054-0059 ACTIVE 0 0 0 _aa_aa _mm_mm1/02/10 0060-0065 ACTIVE 0 0 0 _a_a_a _m_m_m1/02/11 0066-0071 ACTIVE 0 0 0 a__aa_ m__mm_1/02/12 0072-0077 ACTIVE 0 0 0 aaa___ mmm___1/02/13 0078-0083 ACTIVE 0 0 0 aaaa_a mmmm_m1/02/14 0084-0089 ACTIVE 0 0 0 _aaa__ _mmm__1/02/15 0090-0095 ACTIVE 0 0 0 a__aaa m__mmm1/02/16 0096-0101 ACTIVE 0 0 0 _aaaa_ _mmmm_1/02/17 0102-0107 ACTIVE 0 0 0 _aaa_a _mmm_m1/02/18 0108-0113 ACTIVE 1 0 0 _aaaaa _mmmmm1/02/19 0114-0119 ACTIVE 1 0 0 aa_aa_ mm_mm_1/02/20 0120-0125 ACTIVE 1 0 0 aa__aa mm__mm1/02/21 0126-0131 ACTIVE 1 0 0 aaa_aa mmm_mm1/02/22 0132-0137 ACTIVE 1 0 0 _a____ _m____1/02/23 0138-0143 ACTIVE 1 0 0 a__aaa m__mmm1/02/24 0144-0149 ACTIVE 1 0 0 a_a_aa m_m_mm1/02/25 0150-0155 ACTIVE 1 0 0 ___aaa ___mmm1/02/26 0156-0161 ACTIVE 1 0 0 a_a__a m_m__m1/02/27 0162-0167 ACTIVE 1 0 0 a_a_aa m_m_mm1/02/28 0168-0173 ACTIVE 1 0 0 a___aa m___mm1/02/29 0174-0179 ACTIVE 1 0 0 _a____ _m____1/02/30 0180-0185 ACTIVE 1 0 0 _aaaaa _mmmmm1/02/31 0186-0191 ACTIVE 1 0 0 _a_aa_ _m_mm_1/02/32 0192-0197 ACTIVE 1 0 0 aaa__a mmm__m1/02/33 0198-0203 ACTIVE 1 0 0 a_a__a m_m__m1/02/34 0204-0209 ACTIVE 1 0 0 aaaaaa mmmmmm1/02/35 0210-0215 ACTIVE 1 0 0 _aa__a _mm__m1/02/36 0216-0221 ACTIVE 0 0 0 a_a_aa m_m_mm1/02/37 0222-0227 ACTIVE 0 0 0 a_aaaa m_mmmm1/02/38 0228-0233 ACTIVE 0 0 0 aaaaaa mmmmmm1/02/39 0234-0239 ACTIVE 0 0 0 aa_aa_ mm_mm_1/02/40 0240-0245 ACTIVE 0 0 0 aa_aaa mm_mmm1/02/41 0246-0251 ACTIVE 0 0 0 a__a__ m__m__1/02/42 0252-0257 ACTIVE 0 0 0 aa__aa mm__mm1/02/43 0258-0263 ACTIVE 0 0 0 aaa_aa mmm_mm1/02/44 0264-0269 ACTIVE 0 0 0 aaaa_a mmmm_m1/02/45 0270-0275 ACTIVE 0 0 0 aaa_a_ mmm_m_1/02/46 0276-0281 ACTIVE 0 0 0 aaaaa_ mmmmm_1/02/47 0282-0287 ACTIVE 0 0 0 _aaaa_ _mmmm_1/02/48 0288-0293 ACTIVE 0 0 0 a_aa_a m_mm_m1/02/49 0294-0299 ACTIVE 0 0 0 aa_a_a mm_m_m1/02/50 0300-0305 ACTIVE 0 0 0 aa_aaa mm_mmm1/02/51 0306-0311 ACTIVE 0 0 0 aaaaa_ mmmmm_1/02/52 0312-0317 ACTIVE 0 0 0 aaaaaa mmmmmm1/02/53 0318-0323 ACTIVE 0 0 0 aaaa_a mmmm_mRelated Commands
show spe digital
To display digital history statistics of all Service Processing Elements (SPEs) for digital service, in summary form or for SPEs starting with a specified slot or a specified shelf/slot/range of SPEs, use the show spe digital EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe digital [slot | slot/spe]
Note
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
The show spe digital command displays history statistics of all digital SPEs, in summary form or for SPEs starting with a specified slot, or a specified shelf/slot/range of SPEs.
Examples
The following example uses the starting slot/SPE version of the show spe digital command.
router# show spe digital 5/4#SPE 5/04Cisco NextPort SPE; Fw: 0.06.07.03; Async5/24 - 5/29, TTY672 - 677Last clearing of statistics counters : never11 incoming completes 24 incoming failures0 outgoing completes 0 outgoing failures0 failed dial attempts 0 ring no answers0 no dial tones 0 link failures0 watchdog timeouts 0 protocol errors0 dial timeoutsTransmit Speed Counters :Speed Calls Speed Calls Speed Calls Speed CallsSpeed Calls64000 0 28800 0 14400 0 7200 01200 056000 0 24000 0 12000 0 4800 1600 038400 0 19200 10 9600 0 2400 0Receive Speed Counters :Speed Calls Speed Calls Speed Calls Speed CallsSpeed Calls64000 0 28800 0 14400 0 7200 01200 056000 0 24000 0 12000 0 4800 1600 038400 0 19200 10 9600 0 2400 0Related Commands
show spe digital active
To display active digital calls and digital statistics of all Service Processing Elements (SPEs), a specified SPE, or the specified range of SPEs, use the show spe digital active EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe digital active [slot | slot/spe]
Note
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
The show spe digital active command displays active digital calls and digital statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Examples
The following example shows output for the show spe digital active command on the Cisco AS5400 with NextPort DFC. This example displays active digital statistics for slot 5, SPE 6:
router# show spe digital active 5SPE 5/06Char SyncPort Prot Duration Tx/Rx Cfg Loss41 V.110 188 19200/19200 In 0SPE 5/09Char SyncPort Prot Duration Tx/Rx Cfg Loss54 V.110 187 19200/19200 In 056 V.110 187 19200/19200 In 057 V.110 188 19200/19200 In 0...Related Commands
show spe digital csr
To display digital calls success rate (CSR) statistics of all Service Processing Elements (SPEs), a specified SPE, or the specified range of SPEs, use the show spe digital csr EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe digital csr [summary | slot | slot/spe]
Note
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
The show spe digital csr command displays digital calls success rate (CSR) statistics of all SPEs, a specified SPE, or the specified range of SPEs
Examples
The following example shows output for the show spe digital csr command on the Cisco AS5350 with NextPort DFC. This example displays the number of call success rate counters for slot 5
router# show spe digital csr 5Avg Hold Inc calls Out calls Failed No SuccSPE Time Succ Fail Succ Fail Dial Answer Pct5/00 00:04:22 6 0 0 0 0 0 100%5/01 00:04:22 6 0 0 0 0 0 100%5/02 00:04:22 6 0 0 0 0 0 100%5/03 00:04:22 6 0 0 0 0 0 100%5/04 00:04:22 6 0 0 0 0 0 100%5/05 00:04:21 6 0 0 0 0 0 100%5/06 00:04:22 4 0 0 0 0 0 100%5/07 00:04:22 1 0 0 0 0 0 100%5/08 00:04:21 6 0 0 0 0 0 100%5/09 00:04:23 5 0 0 0 0 0 100%5/10 00:00:00 0 0 0 0 0 0 0%5/11 00:04:21 5 0 0 0 0 0 100%5/12 00:04:20 2 0 0 0 0 0 100%5/13 00:00:00 0 0 0 0 0 0 0%5/14 00:00:00 0 0 0 0 0 0 0%5/15 00:00:00 0 0 0 0 0 0 0%5/16 00:00:00 0 0 0 0 0 0 0%5/17 00:00:00 0 0 0 0 0 0 0%Related Commands
show spe digital disconnect-reason
To display the local disconnect reasons for all digital calls on the Service Processing Elements (SPEs), a specified SPE, or the specified range of SPEs, use the show spe digital disconnect-reason EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe digital disconnect-reason [summary | slot | slot/spe]
Note
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
The show spe digital disconnect-reason command displays the local disconnect reasons for all digital calls on the SPEs, a specified SPE, or the specified range of SPEs.
Examples
The following example shows output for the show spe digital disconnect-reason command on the Cisco AS5400 with NextPort DFC. This example displays reasons for digital call disconnects on slot 5:
Router# show spe digital disconnect-reason 5#SPE 5/00 :=====CLASS HOST====== =====CLASS SERVICE=====NonSpecific 0 ATH 0Busy 0 Aborted 0No Answer 0 Connect Timeout 0DTR 0 Sync Loss 0ATH 0NoDialTone 0No Carrier 0ACK 0 TOTAL 0#SPE 5/03 :=====CLASS HOST====== =====CLASS SERVICE=====NonSpecific 0 ATH 0Busy 1 Aborted 0No Answer 0 Connect Timeout 0DTR 0 Sync Loss 0...Related Commands
show spe digital summary
To display summary history statistics of all Service Processing Elements (SPEs), a specified SPE, or the specified range of SPEs, use the show spe digital summary EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe digital summary [slot | slot/spe]
Note
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
The show spe digital summary command displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
Examples
The following example shows output for the show spe digital summary command on the Cisco AS5400 with NextPort DFC. This example displays active digital statistics for slot 5:
Router# show spe digital summary 5Async5/00 - 5/107, TTY648 - 755209 incoming completes 397 incoming failures0 outgoing completes 0 outgoing failures0 failed dial attempts 0 ring no answers0 no dial tones 0 link failures0 watchdog timeouts 0 protocol errors0 dial timeoutsTransmit Speed Counters :Speed Calls Speed Calls Speed Calls Speed CallsSpeed Calls64000 0 28800 0 14400 0 7200 01200 2056000 0 24000 0 12000 0 4800 20600 2038400 0 19200 149 9600 0 2400 0Receive Speed Counters :Speed Calls Speed Calls Speed Calls Speed CallsSpeed Calls64000 0 28800 0 14400 0 7200 01200 2056000 0 24000 0 12000 0 4800 20600 2038400 0 19200 149 9600 0 2400 0..Related Commands.
show spe log
To display the Service Processing Element (SPE) system log, use the show spe log EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe log [reverse | slot]
Cisco AS5800 with Universal Port DFC
show spe log [reverse | shelf/slot]
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Examples
The following example shows output for the show spe log command on the Cisco AS5400 with NextPort DFC:
router# show spe logSlot 3 Events Log2d15h : SPE State Event:Address: 0x3000000SPE : 3/00Command: SPE_IMMEDIATE_DISABLE Complete2d14h : SPE State Event:Address: 0x3000100SPE : 3/06Command: SPE_IMMEDIATE_DISABLE Complete2d13h : SPE State Event:Address: 0x3000200SPE : 3/12Command: SPE_IMMEDIATE_DISABLE Complete00:00:26: SPE State Event:Address: 0x3000001SPE : 3/01Command: SPE_IMMEDIATE_DISABLE CompleteSlot 4 Events Log2d13h : SPE State Event:Address: 0x4000000SPE : 4/00Command: SPE_IMMEDIATE_DISABLE CompleteSlot 7 Events Log2d15h : Diag Post event:Address : 0x7000204SPE : 7/16Result : SPE_POST_TEST_FAILEDTest ID : SPE_POWER_ON_SELF_TESTDiag Code : 0xFE01C004Data Format: ASCIIData Len : 0Related Commands
show spe log reverse
Clears all event entries in the slot history event log.
clear spe log
Displays the slot history event log, with most recent event first.
show spe modem
To display the modem service history statistics for specified Service Processing Element (SPE), use the show spe modem EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe modem {slot | slot/spe}
Cisco AS5800 with Universal Port DFC
show spe modem {shelf/slot | shelf/slot/spe}
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
The show spe modem command displays the modem service history statistics for a specified SPE.
Examples
The following example shows output for the show spe modem command on the Cisco AS5400 with NextPort DFC:
Router# show spe modemAsync1/2/00 - 1/3/323, TTY972 - 16194819 incoming completes 287 incoming failures0 outgoing completes 0 outgoing failures0 failed dial attempts 0 ring no answers 0 autotests0 no carriers 11 dial timeouts 0autotest fails0 no dial tones 0 link failures 0 fail count0 watchdog timeouts 2784 protocol errors 0 recoversTransmit Speed CountersSpeed Calls Speed Calls Speed Calls Speed Calls Speed Calls 60000 0 48000 431 38400 0 30666 0 12000 143 58000 0 46666 0 38000 4 29333 0 9600 5 56000 15 46000 56 37333 110 28800 700 7200 11 54666 0 45333 299 36000 84 28000 5 4800 2 54000 0 44000 226 34666 0 26400 266 2400 0 53333 122 42666 0 34000 39 24000 46 1200 3 52000 562 42000 68 33600 323 21600 27 300 0 50666 0 41333 38 33333 9 19200 38 50000 59 40000 65 32000 20 16800 12 49333 370 38666 0 31200 653 14400 5Receive Speed CountersSpeed Calls Speed Calls Speed Calls Speed Calls Speed Calls 38400 0 26400 2280 16800 11 7200 1 300 2 33600 113 24000 266 14400 139 4800 1 31200 215 21600 56 12000 4 2400 3 28800 1665 19200 47 9600 16 1200 0.The following example shows output for the show spe modem command on the Cisco AS5800 with Universal Port DFC:Router# show spe modem 1/8/0#SPE 1/08/00Cisco Universal SPE; Fw: 0.00.06.81; Async1/8/00 - 1/8/05, TTY2916 - 2921Last clearing of statistics counters : never90 incoming completes 0 incoming failures0 outgoing completes 0 outgoing failures0 failed dial attempts 0 ring no answers 0 autotests0 no carriers 0 dial timeouts 0 autotest fails0 no dial tones 0 link failures 0 fail count0 watchdog timeouts 0 protocol errorsTransmit Speed Counters :Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls60000 0 48000 0 38400 0 30666 0 12000 058000 0 46666 0 38000 0 29333 0 9600 056000 0 46000 0 37333 0 28800 0 7200 054666 0 45333 0 36000 0 28000 0 4800 054000 0 44000 0 34666 0 26400 0 2400 053333 0 42666 0 34000 0 24000 0 1200 052000 0 42000 0 33600 0 21600 0 300 050666 0 41333 0 33333 0 19200 050000 0 40000 0 32000 0 16800 049333 0 38666 0 31200 90 14400 0Receive Speed Counters :Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls38400 0 26400 0 16800 0 7200 0 300 033600 11 24000 0 14400 0 4800 031200 25 21600 0 12000 0 2400 028800 54 19200 0 9600 0 1200 0Related Commands
show spe
Displays history statistics of all SPEs, a specified SPE, or the specified range of SPEs.
show modem
Shows modem service history statistics for the MICA modem.
show spe modem active
To display statistics of all active calls on specified Service Processing Elements (SPEs), use the show spe modem active EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe modem active {slot | slot/spe}
Cisco AS5800 with Universal Port DFC
show spe modem active {shelf/slot | shelf/slot/spe}
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Examples
The following example shows output for the show spe modem active command on the Cisco AS5400 with NextPort DFC.This example displays active modem statistics for slot 5, SPE 6:
Router# show spe modem active 5/6SPE 5/06Port Type Prot Comp Duration Tx/Rx Tx/Rx(Lvl) SNR Cfg Retrain37 V.90 LAP-M V.42bis 95 3890/76 --/-11 38 In 0The following example shows output for the show spe modem active command on the Cisco AS5800 with Universal Port DFC. This example displays active modem statistics for shelf 1, slot 8:
Router# show spe modem active 1/8SPE 1/08/34Port Type Prot Comp Duration Tx/Rx(bps) Tx/Rx(Lvl) SNR Cfg Retrain209 V.34+ LAP-M V.42bis 23 28800/31200 --/-13 37 In 0SPE 1/08/35Port Type Prot Comp Duration Tx/Rx(bps) Tx/Rx(Lvl) SNR Cfg Retrain215 V.34+ LAP-M V.42bis 12 28800/31200 --/-13 37 In 0SPE 1/08/36Port Type Prot Comp Duration Tx/Rx(bps) Tx/Rx(Lvl) SNR Cfg Retrain216 V.34+ LAP-M V.42bis 24 33600/31200 --/-36 38 In 0217 ## ## ## 0 33600/300 --/19 37 In 0218 ## ## ## 0 33600/300 --/19 37 In 0219 ## ## ## 0 33600/300 --/19 35 In 0ÿÿÿRelated Commands
show spe modem csr
To display the call success rate for the specified Service Processing Elements (SPEs), use the show spe modem csr EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe modem csr {summary | slot | slot/spe}
Cisco AS5800 with Universal Port DFC
show spe modem csr {summary | shelf/slot | shelf/slot/spe}
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
The show spe modem csr command displays the modem call success rate statistics for a specific SPE, range of SPEs, or all the SPEs. The summary keyword displays the call success rate statistics for all SPEs.
Examples
The following example shows output for the show spe modem csr summary command on the Cisco AS5400 with NextPort DFC:
Router# show spe modem csr 5/6Avg Hold Inc calls Out calls Failed No SuccSPE Time Succ Fail Succ Fail Dial Answer Pct5/06 00:22:41 2 0 0 0 0 0 100%Router# show spe modem csr 5/1 5/6Avg Hold Inc calls Out calls Failed No SuccSPE Time Succ Fail Succ Fail Dial Answer Pct5/01 00:00:00 0 0 0 0 0 0 0%5/02 00:00:00 0 0 0 0 0 0 0%5/03 00:00:00 0 0 0 0 0 0 0%5/04 00:00:00 0 0 0 0 0 0 0%5/05 00:00:00 0 0 0 0 0 0 0%5/06 00:22:48 2 0 0 0 0 0 100%The following example shows output for the show spe modem csr summary command on the Cisco AS5800 with Universal Port DFC:
Router# show spe modem csr summaryAvg Hold Inc calls Out calls Failed No SuccTime Succ Fail Avail Succ Fail Avail Dial Answer Pct002631 4827 285 93 0 0 93 5 0 94%Related Commands
show spe modem disconnect-reason
To display all modem disconnect reasons for the specified Service Processing Element (SPE), use the show spe modem disconnect-reason EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe modem disconnect-reason {summary | slot | slot/spe}
Cisco AS5800 with Universal Port DFC
show spe modem disconnect-reason {summary | shelf/slot | shelf/slot/spe}
Syntax Description
Command Modes
EXEC
Command History
Usage Guidelines
Disconnect reasons are reasons why active calls are disconnected. The disconnect reasons are displayed with Class boundaries. The show spe modem disconnect-reason command is equivalent to the show modem call stats MCIA modem command.
Examples
The following example shows output for the show spe modem disconnect-reason summary command on the Cisco AS5400 with NextPort DFC:
Router# show spe modem disconnect-reason 5/6#SPE 5/06 :===CLASS OTHER==== =====CLASS DSP==== ===CLASS EC LCL=== ==CLASS EC FRMR===Software Rst 0 No Carrier 0 No LR 0 Frmr Bad Cmd 0EC Termntd 0 No ABT dtctd 0 LR Param1 0 Frmr Data 0Bad MNP5 Rx 0 Trainup flr 0 LR Incmpt 0 Frmr Length 0Bad V42B 0 Retrain Lt 0 Retrns Lt 0 Frmr Bad NR 0Bad COP stat 0 ABT end flr 0 Inactivity 0ATH 0 Protocol Err 0 ===CLASS EC LD====Aborted 0 ====CLASS HOST==== Fallbck Term 0 LD No LR 0Connect Tout 0 Hst NonSpec 0 No XID 0 LD LR Param1 0Reset DSP 0 Hst Busy 0 XID Incmpt 0 LD LR Incmpt 0Hst No answr 0 Disc 0 LD Retrns Lt 0===CLASS EC Cmd=== Hst DTR 1 DM 0 LD Inactivty 0Bad Cmd 0 Hst ATH 0 Bad NR 0 LD Protocol 0Hst NoDialTn 0 SABME Online 0 LD User 0=====N O N E====== Hst No Carr 0 XID Online 0None 0 Hst Ack 0 LR Online 0 TOTAL 1The following example shows the output for the show spe modem disconnect-reason command on the Cisco AS5800 with Universal Port DFC:
Router# show spe modem disconnect-reason===CLASS OTHER==== =====CLASS DSP==== ===CLASS EC LCL=== ==CLASS EC FRMR===Software Rst 0 No Carrier 21 No LR 0 Frmr Bad Cmd 0EC Termntd 0 No ABT dtctd 0 LR Param1 0 Frmr Data 0Bad MNP5 Rx 0 Trainup flr 26 LR Incmpt 0 Frmr Length 0Bad V42B 12 Retrain Lt 0 Retrns Lt 37 Frmr Bad NR 0Bad COP stat 0 ABT end flr 0 Inactivity 0ATH 0 Protocol Err 5 ===CLASS EC LD====Aborted 0 ====CLASS HOST==== Fallbck Term 22 LD No LR 0Connect Tout 11 Hst NonSpec 799 No XID 5 LD LR Param1 0Reset DSP 0 Hst Busy 0 XID Incmpt 0 LD LR Incmpt 0Hst No answr 0 Disc 2718 LD Retrns Lt 0===CLASS EC Cmd=== Hst DTR 870 DM 0 LD Inactivty 0Bad Cmd 0 Hst ATH 0 Bad NR 0 LD Protocol 0Hst NoDialTn 0 SABME Online 0 LD User 0=====N O N E====== Hst No Carr 0 XID Online 0None 29 Hst Ack 0 LR Online 0 TOTAL 4555Related Commands
show spe modem high speed
To display the total number of connections within each modulization or codec for a specific range of Service Processing Elements (SPEs), use the show spe modem high speed EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe modem high speed {summary | slot | slot/spe}
Cisco AS5800 with Universal Port DFC
show spe modem high speed {summary | shelf/slot | shelf/slot/spe}
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Examples
The following example shows output for the show spe modem high speed command on the Cisco AS5400 with NextPort DFC:
Router# show spe modem high speed#SPE 1/0 :Modln V.FC V.34 K56Flex V.90 ModlnSpeed Tx Rx Tx Rx Tx Rx Tx Rx Speed56000 ------ ------ ------ ------ 000000 ------ 000000 ------ 5600054667 ------ ------ ------ ------ - - 0 - 5466754000 ------ ------ ------ ------ 0 - - - 5400053333 ------ ------ ------ ------ - - 0 - 5333352000 ------ ------ ------ ------ 0 - 0 - 5200050667 ------ ------ ------ ------ - - 0 - 5066750000 ------ ------ ------ ------ 0 - - - 5000049333 ------ ------ ------ ------ - - 0 - 4933348000 ------ ------ ------ ------ 0 - 0 - 4800046667 ------ ------ ------ ------ - - 0 - 4666746000 ------ ------ ------ ------ 0 - - - 4600045333 ------ ------ ------ ------ - - 0 - 4533344000 ------ ------ ------ ------ 0 - 0 - 4400042667 ------ ------ ------ ------ - - 0 - 4266742000 ------ ------ ------ ------ 0 - - - 4200041333 ------ ------ ------ ------ - - 0 - 4133340000 ------ ------ ------ ------ 0 - 0 - 4000038667 ------ ------ ------ ------ - - 0 - 4866738000 ------ ------ ------ ------ 0 - - - 3800037333 ------ ------ ------ ------ - - 0 - 3733336000 ------ ------ ------ ------ 0 - 0 - 3600034667 ------ ------ ------ ------ - - 0 - 3466734000 ------ ------ ------ ------ 0 - - - 3400033600 ------ ------ 0 0 - - - 0 3360033333 ------ ------ - - - - 0 - 3333332000 ------ ------ - - 0 - 0 - 3200031200 ------ ------ 0 0 - 0 - 0 3120030667 ------ ------ - - - - 0 - 3066729333 ------ ------ - - - - 0 - 2933328800 0 0 0 0 - 0 - 0 2880028000 - - - - - - 0 - 2800026400 0 0 0 0 - 0 - 0 2640024000 0 0 0 0 - 0 - 0 2400021600 0 0 0 0 - 0 - 0 2160019200 0 0 0 0 - 0 - 0 1920016800 0 0 0 0 - 0 - 0 1680014400 0 0 0 0 - 0 - 0 1440012000 - - 0 0 - 0 - 0 120009600 - - 0 0 - 0 - 0 96007200 - - 0 0 - 0 - 0 72004800 - - 0 0 - 0 - 0 48002400 - - 0 0 - - - - 2400TOTAL 0000000 0000000 0000000 0000000 TOTAL#SPE 1/1 :Modln V.FC V.34 K56Flex V.90 ModlnSpeed Tx Rx Tx Rx Tx Rx Tx Rx Speed56000 ------ ------ ------ ------ 000000 ------ 000000 ------ 5600054667 ------ ------ ------ ------ - - 0 - 5466754000 ------ ------ ------ ------ 0 - - - 5400053333 ------ ------ ------ ------ - - 0 - 5333352000 ------ ------ ------ ------ 0 - 0 - 5200050667 ------ ------ ------ ------ - - 0 - 5066750000 ------ ------ ------ ------ 0 - - - 5000049333 ------ ------ ------ ------ - - 0 - 4933348000 ------ ------ ------ ------ 0 - 0 - 4800046667 ------ ------ ------ ------ - - 0 - 4666746000 ------ ------ ------ ------ 0 - - - 4600045333 ------ ------ ------ ------ - - 0 - 4533344000 ------ ------ ------ ------ 0 - 0 - 4400042667 ------ ------ ------ ------ - - 0 - 4266742000 ------ ------ ------ ------ 0 - - - 4200041333 ------ ------ ------ ------ - - 0 - 4133340000 ------ ------ ------ ------ 0 - 0 - 4000038667 ------ ------ ------ ------ - - 0 - 4866738000 ------ ------ ------ ------ 0 - - - 3800037333 ------ ------ ------ ------ - - 0 - 3733336000 ------ ------ ------ ------ 0 - 0 - 3600034667 ------ ------ ------ ------ - - 0 - 3466734000 ------ ------ ------ ------ 0 - - - 3400033600 ------ ------ 0 0 - - - 0 3360033333 ------ ------ - - - - 0 - 3333332000 ------ ------ - - 0 - 0 - 3200031200 ------ ------ 0 0 - 0 - 0 3120030667 ------ ------ - - - - 0 - 3066729333 ------ ------ - - - - 0 - 2933328800 0 0 0 0 - 0 - 0 2880028000 - - - - - - 0 - 2800026400 0 0 0 0 - 0 - 0 2640024000 0 0 0 0 - 0 - 0 2400021600 0 0 0 0 - 0 - 0 2160019200 0 0 0 0 - 0 - 0 1920016800 0 0 0 0 - 0 - 0 1680014400 0 0 0 0 - 0 - 0 1440012000 - - 0 0 - 0 - 0 120009600 - - 0 0 - 0 - 0 96007200 - - 0 0 - 0 - 0 72004800 - - 0 0 - 0 - 0 48002400 - - 0 0 - - - - 2400TOTAL 0000000 0000000 0000000 0000000 TOTAL.The following example shows output for the show spe modem high speed command on the Cisco AS5800 with Universal Port DFC:
Router# show spe modem high speed 1/8/1-- Indicates an invalid speed for a standard#SPE 1/08/01 :Modln V.FC V.34 K56Flex V.90 ModlnSpeed Tx Rx Tx Rx Tx Rx Tx Rx Speed60000 ------ ------ ------ ------ 000000 ------ ------ ------ 6000058000 ------ ------ ------ ------ 0 ------ ------ ------ 5800056000 ------ ------ ------ ------ 0 - 0 - 5600054667 ------ ------ ------ ------ - - 0 - 5466754000 ------ ------ ------ ------ 0 - - - 5400053333 ------ ------ ------ ------ - - 0 - 5333352000 ------ ------ ------ ------ 0 - 0 - 5200050667 ------ ------ ------ ------ - - 0 - 5066750000 ------ ------ ------ ------ 0 - - - 5000049333 ------ ------ ------ ------ - - 0 - 4933348000 ------ ------ ------ ------ 0 - 0 - 4800046667 ------ ------ ------ ------ - - 0 - 4666746000 ------ ------ ------ ------ 0 - - - 4600045333 ------ ------ ------ ------ - - 0 - 4533344000 ------ ------ ------ ------ 0 - 0 - 4400042667 ------ ------ ------ ------ - - 0 - 4266742000 ------ ------ ------ ------ 0 - - - 4200041333 ------ ------ ------ ------ - - 0 - 4133340000 ------ ------ ------ ------ 0 - 0 - 4000038667 ------ ------ ------ ------ - - 0 - 3866738400 ------ ------ ------ ------ - - - - 3840038000 ------ ------ ------ ------ 0 - - - 3800037333 ------ ------ ------ ------ - - 0 - 3733336000 ------ ------ ------ ------ 0 - 0 - 3600034666 ------ ------ ------ ------ - - 0 - 3466634000 ------ ------ ------ ------ 0 - - - 3400033600 ------ ------ 0 1 - - - 0 3360033333 ------ ------ - - - - 0 - 3333332000 ------ ------ - - 0 - 0 - 3200031200 ------ ------ 6 1 - 0 - 0 3120030667 ------ ------ - - - - 0 - 3066729333 ------ ------ - - - - 0 - 2933328800 0 0 0 4 - 0 - 0 2880028000 - - - - - - 0 - 2800026400 0 0 0 0 - 0 - 0 2640024000 0 0 0 0 - 0 - 0 2400021600 0 0 0 0 - 0 - 0 2160019200 0 0 0 0 - 0 - 0 1920016800 0 0 0 0 - 0 - 0 1680014400 0 0 0 0 - 0 - 0 1440012000 - - 0 0 - 0 - 0 120009600 - - 0 0 - 0 - 0 96007200 - - 0 0 - 0 - 0 72004800 - - 0 0 - 0 - 0 48002400 - - 0 0 - - - - 2400TOTAL 0000000 0000012 0000000 0000000Related Commands
show spe modem low speed
Displays the connect-speeds within each low-speed modulation or codec for the specified Service Processing Elements (SPEs).
show spe modem high standard
To display the total number of connections within each high modulation or codec for a specific range of Service Processing Element (SPE), use the show spe modem high standard EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe modem high standard {summary | slot | slot/spe}
Cisco AS5800 with Universal Port DFC
show spe modem high standard {summary | shelf/slot | shelf/slot/spe}
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Examples
The following example shows output for the show spe modem high standard command on the Cisco AS5400 with NextPort DFC. This example displays standard low-speed connections for SPEs in slot 5:Router# show spe modem high standard 5SPE/Mod-> V.FC V.34 K56Flex V.905/00 0 1 2 15/01 0 0 0 05/02 0 0 0 05/03 0 0 0 05/04 0 0 0 05/05 0 0 0 05/06 0 0 0 25/07 0 0 0 05/08 0 0 0 05/09 0 0 0 05/10 0 0 0 05/11 0 0 0 05/12 0 0 0 05/13 0 0 0 05/14 0 0 0 05/15 0 0 0 05/16 0 0 0 05/17 0 0 0 0TOTAL 00000000 00000001 00000002 00000003The following example shows output for the show spe modem high standard command on the Cisco AS5800 with Universal Port DFC. This example displays standard low-speed connections for SPEs in slot 8:Router# show spe modem high standard 1/8/1SPE/Mod-> V.FC V.34 K56Flex V.901/08/01 0 6 0 0TOTAL 00000000 00000006 00000000 00000000Related Commands
show spe modem low standard
Displays the connect-speeds within each low-speed modulation or codec for the SPE.
show spe modem low speed
To display the connect-speeds within each low-speed modulation or codec for the specified Service Processing Elements (SPEs), use the show spe modem low speed EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe modem low speed {summary | slot | slot/spe}
Cisco AS5800 with Universal Port DFC
show spe modem low speed {summary | shelf/slot | shelf/slot/spe}
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Examples
The following example shows output for the show spe modem low speed command on the Cisco AS5400 with NextPort DFC. This example displays standard low-speed connections:Router# show spe modem low speed#SPE 1/0 : <-- MODEM FAX -->Speed B103 V.21 B212 V.22 V.22b V.32 V.32b V.27t V.29 V.1714400 ------ ------ ------ ------ ------ ------ 30 ------ ------ 012000 ------ ------ ------ ------ ------ ------ 0 ------ ------ 09600 ------ ------ ------ ------ ------ 0 0 ------ 0 07200 ------ ------ ------ ------ ------ - 0 ------ 0 04800 ------ ------ ------ ------ ------ 0 0 0 0 ------2400 ------ ------ ------ ------ 0 ------ ------ 0 ------ ------1200 ------ ------ 0 0 6 ------ ------ ------ ------ ------600 ------ ------ ------ ------ ------ ------ ------ ------ ------ ------300 0 0 ------ ------ ------ ------ ------ ------ ------ ------TOTAL 000000 000000 000000 000000 000006 000000 000030 000000 000000 000000#SPE 1/1 : <-- MODEM FAX -->Speed B103 V.21 B212 V.22 V.22b V.32 V.32b V.27t V.29 V.1714400 ------ ------ ------ ------ ------ ------ 30 ------ ------ 012000 ------ ------ ------ ------ ------ ------ 0 ------ ------ 09600 ------ ------ ------ ------ ------ 0 0 ------ 0 07200 ------ ------ ------ ------ ------ - 0 ------ 0 04800 ------ ------ ------ ------ ------ 0 0 0 0 ------2400 ------ ------ ------ ------ 0 ------ ------ 0 ------ ------1200 ------ ------ 0 0 6 ------ ------ ------ ------ ------600 ------ ------ ------ ------ ------ ------ ------ ------ ------ ------300 0 0 ------ ------ ------ ------ ------ ------ ------ ------TOTAL 000000 000000 000000 000000 000006 000000 000030 000000 000000 000000The following example shows output for the show spe modem low speed command on the Cisco AS5800 with Universal Port DFC. This example displays standard low-speed connections for SPEs in slot 8:
Router# show spe modem low speed 1/8/0 1/8/6-- Indicates an invalid speed for a standard#SPE 1/08/00 : <-- MODEM FAX -->Speed B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.1714400 ----- ----- ----- ----- ----- ----- ----- 0 ----- ----- 012000 ----- ----- ----- ----- ----- ----- ----- 0 ----- ----- 09600 ----- ----- ----- ----- ----- ----- 0 0 ----- 0 07200 ----- ----- ----- ----- ----- ----- - 0 ----- 0 04800 ----- ----- ----- ----- ----- ----- 0 0 0 0 -----2400 ----- ----- ----- ----- 0 ----- ----- ----- 0 ----- -----1200 ----- ----- 0 0 0 0 ----- ----- ----- ----- -----300 0 0 ----- ----- ----- ----- ----- ----- ----- ----- -----TOTAL 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000ÿRelated Commands
show spe modem high speed
Displays the total number of connections within each modulization or codec for a specific range of Service Processing Elements (SPEs).
show spe modem low standard
To display the total number of connections within each low modulation or codec for the specified Service Processing Elements (SPEs), use the show spe modem low standard EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe modem low standard {summary | slot | slot/spe}
Cisco AS5800 with Universal Port DFC
show spe modem low standard {summary | shelf/slot | shelf/slot/spe}
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Examples
The following example displays standard low speed connections for SPEs in slot 5 on the Cisco AS5400.Router# show spe modem low standard 5<-- MODEM FAX -->SPE/Mod-> B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.175/00 0 0 0 0 0 0 0 0 0 0 05/01 0 0 0 0 0 0 0 0 0 0 05/02 0 0 0 0 0 0 0 0 0 0 05/03 0 0 0 0 0 0 0 0 0 0 05/04 0 0 0 0 0 0 0 0 0 0 05/05 0 0 0 0 0 0 0 0 0 0 05/06 0 0 0 0 0 0 0 0 0 0 05/07 0 0 0 0 0 0 0 0 0 0 05/08 0 0 0 0 0 0 0 0 0 0 05/09 0 0 0 0 0 0 0 0 0 0 05/10 0 0 0 0 0 0 0 0 0 0 05/11 0 0 0 0 0 0 0 0 0 0 05/12 0 0 0 0 0 0 0 0 0 0 05/13 0 0 0 0 0 0 0 0 0 0 05/14 0 0 0 0 0 0 0 0 0 0 05/15 0 0 0 0 0 0 0 0 0 0 05/16 0 0 0 0 0 0 0 0 0 0 05/17 0 0 0 0 0 0 0 0 0 0 0TOTAL 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000The following example displays standard low speed connections for SPEs in slot 8 on the Cisco AS5800.
Router# show spe modem low standard 1/8<-- MODEM FAX -->SPE/Mod-> B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.171/08/00 0 0 0 0 0 0 0 0 0 0 01/08/01 0 0 0 0 0 0 0 0 0 0 01/08/02 0 0 0 0 0 0 0 0 0 0 01/08/03 0 0 0 0 0 0 0 0 0 0 01/08/04 0 0 0 0 0 0 0 0 0 0 01/08/05 0 0 0 0 0 0 0 0 0 0 01/08/06 0 0 0 0 0 0 0 0 0 0 01/08/07 0 0 0 0 0 0 0 0 0 0 01/08/08 0 0 0 0 0 0 0 0 0 0 01/08/09 0 0 0 0 0 0 0 0 0 0 01/08/10 0 0 0 0 0 0 0 0 0 0 01/08/11 0 0 0 0 0 0 0 0 0 0 01/08/12 0 0 0 0 0 0 0 0 0 0 01/08/13 0 0 0 0 0 0 0 0 0 0 01/08/14 0 0 0 0 0 0 0 0 0 0 01/08/15 0 0 0 0 0 0 0 0 0 0 01/08/16 0 0 0 0 0 0 0 0 0 0 01/08/17 0 0 0 0 0 0 0 0 0 0 01/08/18 0 0 0 0 0 0 0 0 0 0 01/08/19 0 0 0 0 0 0 0 0 0 0 01/08/20 0 0 0 0 0 0 0 0 0 0 0<-- MODEM FAX -->SPE/Mod-> B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.171/08/21 0 0 0 0 0 0 0 0 0 0 01/08/22 0 0 0 0 0 0 0 0 0 0 01/08/23 0 0 0 0 0 0 0 0 0 0 01/08/24 0 0 0 0 0 0 0 0 0 0 01/08/25 0 0 0 0 0 0 0 0 0 0 01/08/26 0 0 0 0 0 0 0 0 0 0 01/08/27 0 0 0 0 0 0 0 0 0 0 01/08/28 0 0 0 0 0 0 0 0 0 0 01/08/29 0 0 0 0 0 0 0 0 0 0 01/08/30 0 0 0 0 0 0 0 0 0 0 01/08/31 0 0 0 0 0 0 0 0 0 0 01/08/32 0 0 0 0 0 0 0 0 0 0 01/08/33 0 0 0 0 0 0 0 0 0 0 01/08/34 0 0 0 0 0 0 0 0 0 0 01/08/35 0 0 0 0 0 0 0 0 0 0 01/08/36 0 0 0 0 0 0 0 0 0 0 01/08/37 0 0 0 0 0 0 0 0 0 0 01/08/38 0 0 0 0 0 0 0 0 0 0 01/08/39 0 0 0 0 0 0 0 0 0 0 01/08/40 0 0 0 0 0 0 0 0 0 0 01/08/41 0 0 0 0 0 0 0 0 0 0 01/08/42 0 0 0 0 0 0 0 0 0 0 0<-- MODEM FAX -->SPE/Mod-> B103 V.21 B212 V.22 V.22b V.23 V.32 V.32b V.27t V.29 V.171/08/43 0 0 0 0 0 0 0 0 0 0 01/08/44 0 0 0 0 0 0 0 0 0 0 01/08/45 0 0 0 0 0 0 0 0 0 0 01/08/46 0 0 0 0 0 0 0 0 0 0 01/08/47 0 0 0 0 0 0 0 0 0 0 01/08/48 0 0 0 0 0 0 0 0 0 0 01/08/49 0 0 0 0 0 0 0 0 0 0 01/08/50 0 0 0 0 0 0 0 0 0 0 01/08/51 0 0 0 0 0 0 0 0 0 0 01/08/52 0 0 0 0 0 0 0 0 0 0 01/08/53 0 0 0 0 0 0 0 0 0 0 0TOTAL 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000 00000Related Commands
show spe modem high standard
Displays the total number of connections within each high modulation or codec for a specific range of SPE.
show spe modem summary
To display summary of modem statistics for the specified Service Processing Element (SPE) or range of SPEs, use the show spe modem summary EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe modem summary [slot | slot/spe]
Cisco AS5800 with Universal Port DFC
show spe modem summary [shelf/slot | shelf/slot/spe]
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Examples
The following example displays the show spe modem summary command on the Cisco AS5400.
Router# show spe modem summaryAsync1/00 - 5/107, TTY216 - 755786 incoming completes 4 incoming failures0 outgoing completes 0 outgoing failures0 failed dial attempts 0 ring no answers 0 autotests0 no carriers 0 dial timeouts 0 autotest fails0 no dial tones 0 link failures 0 fail count0 watchdog timeouts 0 protocol errors 0 recoversTransmit Speed Counters :Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls60000 0 48000 0 38400 0 30666 0 12000 058000 0 46666 0 38000 0 29333 0 9600 056000 0 46000 0 37333 0 28800 10 7200 054666 0 45333 0 36000 0 28000 0 4800 054000 0 44000 0 34666 0 26400 0 2400 053333 0 42666 0 34000 0 24000 0 1200 052000 0 42000 0 33600 631 21600 0 300 050666 0 41333 0 33333 0 19200 050000 0 40000 0 32000 0 16800 049333 0 38666 0 31200 145 14400 0Transmit Speed Counters :Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls60000 0 48000 0 38400 0 30666 0 12000 058000 0 46666 0 38000 0 29333 0 9600 056000 0 46000 0 37333 0 28800 10 7200 054666 0 45333 0 36000 0 28000 0 4800 054000 0 44000 0 34666 0 26400 0 2400 053333 0 42666 0 34000 0 24000 0 1200 052000 0 42000 0 33600 631 21600 0 300 050666 0 41333 0 33333 0 19200 050000 0 40000 0 32000 0 16800 049333 0 38666 0 31200 145 14400 0Receive Speed Counters :Speed Calls Speed Calls Speed Calls Speed Calls Speed Calls38400 0 26400 0 16800 0 7200 0 300 033600 786 24000 0 14400 0 4800 031200 0 21600 0 12000 0 2400 028800 0 19200 0 9600 0 1200 0The following example displays the show spe modem summary command on the Cisco AS5800.
Router# show spe modem summaryAsync1/2/00 - 1/3/323, TTY972 - 16194827 incoming completes 284 incoming failures0 outgoing completes 0 outgoing failures0 failed dial attempts 0 ring no answers 0 autotests0 no carriers 11 dial timeouts 0 autotest fails0 no dial tones 0 link failures 0 fail count0 watchdog timeouts 2787 protocol errors 0 recoversTransmit Speed CountersSpeed Calls Speed Calls Speed Calls Speed Calls Speed Calls60000 0 48000 432 38400 0 30666 0 12000 14358000 0 46666 0 38000 4 29333 0 9600 556000 15 46000 56 37333 111 28800 700 7200 1154666 0 45333 299 36000 84 28000 5 4800 254000 0 44000 227 34666 0 26400 267 2400 053333 123 42666 0 34000 39 24000 46 1200 352000 563 42000 68 33600 323 21600 27 300 050666 0 41333 38 33333 9 19200 3850000 59 40000 65 32000 20 16800 1249333 371 38666 0 31200 654 14400 5Receive Speed CountersSpeed Calls Speed Calls Speed Calls Speed Calls Speed Calls38400 0 26400 2286 16800 11 7200 1 300 233600 113 24000 267 14400 139 4800 131200 216 21600 56 12000 4 2400 328800 1665 19200 47 9600 16 1200 0Related Commands
show spe recovery
To display SPE recovery statistics, use the show spe recovery EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe recovery [slot | slot/spe]
Cisco AS5800 with Universal Port DFC
show spe recovery [shelf/slot | shelf/slot/spe]
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
Use this command to see a list of recovered SPEs.
Examples
The following example displays the show spe recovery command on the Cisco AS5400.
Router# show spe recoverySPE# Session Abort Session NAK Call Failure1/00 0 0 01/01 0 0 01/02 0 0 01/03 0 0 01/04 0 0 01/05 0 0 01/06 0 0 01/07 0 0 01/08 0 0 01/09 0 0 01/10 0 0 01/11 0 0 01/12 0 0 01/13 0 0 01/14 0 0 01/15 0 0 01/16 0 0 01/17 0 0 0The following example displays the show spe recovery command on the Cisco AS5800.
Router# show spe recovery 1/8SPE# Session Abort Session NAK Call Failure1/08/00 0 0 01/08/01 0 0 01/08/02 0 0 01/08/03 0 0 01/08/04 0 0 01/08/05 0 0 01/08/06 0 0 01/08/07 0 0 01/08/08 0 0 01/08/09 0 0 01/08/10 0 0 01/08/11 0 0 01/08/12 0 0 01/08/13 0 0 01/08/14 0 0 01/08/15 0 0 01/08/16 0 0 01/08/17 0 0 01/08/18 0 0 01/08/19 0 0 01/08/20 0 0 01/08/21 0 0 01/08/22 0 0 01/08/23 0 0 01/08/24 0 0 01/08/25 0 0 01/08/26 0 0 01/08/27 0 0 01/08/28 0 0 01/08/29 0 0 01/08/30 0 0 01/08/31 0 0 01/08/32 0 0 01/08/33 0 0 01/08/34 0 0 01/08/35 0 0 01/08/36 0 0 01/08/37 0 0 01/08/38 0 0 01/08/39 0 0 01/08/40 0 0 01/08/41 0 0 01/08/42 0 0 01/08/43 0 0 01/08/44 0 0 01/08/45 0 0 01/08/46 0 0 01/08/47 0 0 01/08/48 0 0 01/08/49 0 0 01/08/50 0 0 01/08/51 0 0 01/08/52 0 0 01/08/53 0 0 0Related Commands
show spe version
To display the firmware version on a Service Processing Element (SPE), use the show spe version EXEC command. Also, this command displays the version to firmware file mappings.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
show spe version [slot | slot/spe]
Cisco AS5800 with Universal Port DFC
show spe version [shelf/slot | shelf/slot/spe]
Syntax Description
Defaults
No default behavior or values.
Command Modes
EXEC
Command History
Usage Guidelines
Use the show spe version command to display the firmware version running on a specific SPE. If shelf/slot/spe is specified, the firmware version for the identified SPE or range of SPEs is displayed. If slot is specified, the firmware version for the identified SPEs in this slot or range of slots is displayed. If no argument is specified, all SPE versions are displayed.
Note
Examples
The following example displays the output of show spe version on a Cisco AS5400:
Router# show spe versionIOS-Bundled Default Firmware-Filename Version Firmware-Type===================================== ======= =============system:/ucode/np_spe_firmware1 0.6.5.5 SPE firmware0.0.0.0 PortwareOn-Flash Firmware-Filename Version Firmware-Type========================== ======= =============flash:np.spe 0.6.4.5 SPE firmwareSPE-# SPE-Type SPE-Port-Range Version UPG Firmware-Filename4/00 CSMV6 0000-0005 0.6.5.5 N/A np.spe4/01 CSMV6 0006-0011 0.6.5.5 N/A ios-bundled default4/02 CSMV6 0012-0017 0.6.5.5 N/A ios-bundled default4/03 CSMV6 0018-0023 0.6.5.5 N/A ios-bundled default4/04 CSMV6 0024-0029 0.6.5.5 N/A ios-bundled default4/05 CSMV6 0030-0035 0.6.5.5 N/A ios-bundled default4/06 CSMV6 0036-0041 0.6.5.5 N/A ios-bundled default4/07 CSMV6 0042-0047 0.6.5.5 N/A ios-bundled default4/08 CSMV6 0048-0053 0.6.5.5 N/A ios-bundled default4/09 CSMV6 0054-0059 0.6.5.5 N/A ios-bundled default4/10 CSMV6 0060-0065 0.6.5.5 N/A ios-bundled default4/11 CSMV6 0066-0071 0.6.5.5 N/A ios-bundled default4/12 CSMV6 0072-0077 0.6.5.5 N/A ios-bundled default4/13 CSMV6 0078-0083 0.6.5.5 N/A ios-bundled default4/14 CSMV6 0084-0089 0.6.5.5 N/A ios-bundled default4/15 CSMV6 0090-0095 0.6.5.5 N/A ios-bundled default4/16 CSMV6 0096-0101 0.6.5.5 N/A ios-bundled default4/17 CSMV6 0102-0107 0.6.5.5 N/A ios-bundled defaultThe following example displays the output of show spe version on a Cisco AS5800:
Router# show spe version 1/8IOS-Bundled Default Firmware-Filename Version Firmware-Type===================================== ======= =============system:/ucode/np_spe_firmware1 0.0.6.81 SPE firmwaresystem:/ucode/mica_board_firmware 2.7.2.0 Mica PortwareOn-Flash Firmware-Filename Version Firmware-Type========================== ======= =============slot0:np_6_81.spe 0.0.6.81 SPE firmwareslot0:np_6_80.spe 0.0.6.80 SPE firmwareslot0:mica-modem-pw.2.7.1.1.bin 2.7.1.0 Mica Portwareslot0:mica-modem-pw.2.7.2.0.bin 2.7.2.0 Mica PortwareSPE-# SPE-Type SPE-Port-Range Version UPG Firmware-Filename1/08/00 CSMV6 0000-0005 0.0.6.81 N/A ios-bundled default1/08/01 CSMV6 0006-0011 0.0.6.81 N/A ios-bundled default1/08/02 CSMV6 0012-0017 0.0.6.81 N/A ios-bundled default1/08/03 CSMV6 0018-0023 0.0.6.81 N/A ios-bundled default1/08/04 CSMV6 0024-0029 0.0.6.81 N/A ios-bundled default1/08/05 CSMV6 0030-0035 0.0.6.81 N/A ios-bundled default1/08/06 CSMV6 0036-0041 0.0.6.81 N/A ios-bundled default1/08/07 CSMV6 0042-0047 0.0.6.81 N/A ios-bundled default1/08/08 CSMV6 0048-0053 0.0.6.81 N/A ios-bundled default1/08/09 CSMV6 0054-0059 0.0.6.81 N/A ios-bundled default1/08/10 CSMV6 0060-0065 0.0.6.81 N/A ios-bundled default1/08/11 CSMV6 0066-0071 0.0.6.81 N/A ios-bundled default1/08/12 CSMV6 0072-0077 0.0.6.81 N/A ios-bundled default1/08/13 CSMV6 0078-0083 0.0.6.81 N/A ios-bundled default1/08/14 CSMV6 0084-0089 0.0.6.81 N/A ios-bundled default1/08/15 CSMV6 0090-0095 0.0.6.81 N/A ios-bundled default1/08/16 CSMV6 0096-0101 0.0.6.81 N/A ios-bundled default1/08/17 CSMV6 0102-0107 0.0.6.81 N/A ios-bundled default1/08/18 CSMV6 0108-0113 0.0.6.81 N/A ios-bundled default1/08/19 CSMV6 0114-0119 0.0.6.81 N/A ios-bundled default1/08/20 CSMV6 0120-0125 0.0.6.81 N/A ios-bundled default1/08/21 CSMV6 0126-0131 0.0.6.81 N/A ios-bundled default1/08/22 CSMV6 0132-0137 0.0.6.81 N/A ios-bundled default1/08/23 CSMV6 0138-0143 0.0.6.81 N/A ios-bundled default1/08/24 CSMV6 0144-0149 0.0.6.81 N/A ios-bundled default1/08/25 CSMV6 0150-0155 0.0.6.81 N/A ios-bundled default1/08/26 CSMV6 0156-0161 0.0.6.81 N/A ios-bundled default1/08/27 CSMV6 0162-0167 0.0.6.81 N/A ios-bundled default1/08/28 CSMV6 0168-0173 0.0.6.81 N/A ios-bundled default1/08/29 CSMV6 0174-0179 0.0.6.81 N/A ios-bundled default1/08/30 CSMV6 0180-0185 0.0.6.81 N/A ios-bundled default1/08/31 CSMV6 0186-0191 0.0.6.81 N/A ios-bundled default1/08/32 CSMV6 0192-0197 0.0.6.81 N/A ios-bundled default1/08/33 CSMV6 0198-0203 0.0.6.81 N/A ios-bundled default1/08/34 CSMV6 0204-0209 0.0.6.81 N/A ios-bundled default1/08/35 CSMV6 0210-0215 0.0.6.81 N/A ios-bundled default1/08/36 CSMV6 0216-0221 0.0.6.81 N/A ios-bundled default1/08/37 CSMV6 0222-0227 0.0.6.81 N/A ios-bundled default1/08/38 CSMV6 0228-0233 0.0.6.81 N/A ios-bundled default1/08/39 CSMV6 0234-0239 0.0.6.81 N/A ios-bundled default1/08/40 CSMV6 0240-0245 0.0.6.81 N/A ios-bundled default1/08/41 CSMV6 0246-0251 0.0.6.81 N/A ios-bundled default1/08/42 CSMV6 0252-0257 0.0.6.81 N/A ios-bundled default1/08/43 CSMV6 0258-0263 0.0.6.81 N/A ios-bundled default1/08/44 CSMV6 0264-0269 0.0.6.81 N/A ios-bundled default1/08/45 CSMV6 0270-0275 0.0.6.81 N/A ios-bundled default1/08/46 CSMV6 0276-0281 0.0.6.81 N/A ios-bundled default1/08/47 CSMV6 0282-0287 0.0.6.81 N/A ios-bundled default1/08/48 CSMV6 0288-0293 0.0.6.81 N/A ios-bundled default1/08/49 CSMV6 0294-0299 0.0.6.81 N/A ios-bundled default1/08/50 CSMV6 0300-0305 0.0.6.81 N/A ios-bundled default1/08/51 CSMV6 0306-0311 0.0.6.81 N/A ios-bundled default1/08/52 CSMV6 0312-0317 0.0.6.81 N/A ios-bundled default1/08/53 CSMV6 0318-0323 0.0.6.81 N/A ios-bundled defaultRelated Commands
shutdown (port level)
To disable a port, use the shutdown port configuration command. To change the administrative state of a port from out-of-service to in service, use the no form of this command
shutdown
no shutdown
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values.
Command Modes
Port configuration
Command History
Usage Guidelines
The shutdown command is equivalent to the modem shutdown MICA modem command.
Examples
The example below first resets and un-resets port 1 to 18 before executing shutdown command.
router(config)# port 1/1 1/18router(config-port)# shutdownrouter(config-port)# no shutdownrouter(config-port)#Related Commands
shutdown (SPE level)
To take a Service Processing Element (SPE) out of service, use the shutdown spe configuration command. Use the no form of this command to change the administrative state of this SPE from down to up.
shutdown
no shutdown
Syntax Description
This command has no arguments or keywords.
Defaults
No default behavior or values
Command Modes
SPE configuration
Command History
Usage Guidelines
The shutdown SPE configuration command takes a Service Processing Element (SPE) out of service. The no form of this command changes the administrative state of the SPE from down to up.
Examples
The following example first resets port 1 to 18.
router(config)# spe 1/1 1/18router(config-port)# shutdownrouter(config-port)# no shutdownrouter(config-port)#Related Commands
spe
To access the Service Processing Element (SPE) configuration mode and set the range of SPEs, use the spe global configuration command. To exit SPE configuration mode, use the exit command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
spe {slot | slot/spe}
Cisco AS5800 with Universal Port DFC
spe {shelf/slot | shelf/slot/spe}
Syntax Description
Defaults
None
Command Modes
Global configuration
Command History
Usage Guidelines
The spe global configuration command enables the SPE configuration mode. Configure your SPE by specifying a slot and an SPE associated with the slot; or, you can configure a range of SPEs by specifying the first and last SPE in the range.
In the SPE configuration mode, the available SPE configuration commands are shown by typing? in that mode:
router(config)# spe 5/4 5/6router(config-spe)# ?SPE Configuration Commands:busyout Busyout SPEdefault Set a command to its defaultsexit Exit from SPE Configuration Modefirmware Firmware used for the SPEhelp Description of the interactive help systemno Negate a command or set its defaultsshutdown Take the SPE out of ServiceWhen the universal gateway is booted, the spe global configuration command specifies the location from where the firmware image is downloaded to the SPE. If the spe configuration command is used to download the firmware from flash memory and then subsequently the no version of the exact command is entered, then the spe command downloads the embedded firmware.
Note
Caution
Examples
The following example shows the spe command being used from global configuration mode to access the SPE configuration mode for the SPE range from 1/2 to 1/4:
router(config)# spe 1/2 1/4The example below specifies the range for use of the shutdown command.
router(config)# spe 1/1 1/18router(config-spe)# shutdownrouter(config-spe)# no shutdownrouter(config-spe)#Related Commands
Display history statistics of all SPEs, specified SPE or the specified SPE range.
spe call-record modem
To generate a modem call-record at the end of each call, use the spe call-record global configuration command. Use the no form of the command to cancel the request to generate the reports.
spe call-record modem {max-userid number | quiet}
no spe call-record modem {max-userid number | quiet}
Syntax Description
max-userid number
Maximum length of the User ID for the modem call record report in number of bytes. The range is 0 to 100
quiet
Disables logging to the console and the terminal, but not to syslog.
Defaults
SPE call-record Enabled
Command Modes
Global configuration
Command History
Usage Guidelines
The spe modem-call-record command is equivalent to the modem call-record command.
Examples
The following example displays SPE call-record:
router# config trouter(config)# spe call-record modem max-userid 50router(config)# endrouter#00:18:30: %SYS-5-CONFIG_I: Configured from console by consolerouter# writeBuilding configuration...[OK]The following is an example of traces generated when call terminates. The logs from the show port modem log command do not change as a result of using the spe call-record command.
...%LINK-3-UPDOWN: Interface Async5/105, changed state to down%MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/2/15,slot/port=5/37, call_id=EE, userid=touraco-e1-4, ip=79.188.24.1,calling=(n/a), called=35160, std=V.34+, prot=LAP-M, comp=V.42bis,init-rx/tx b-rate=33600/33600, finl-rx/tx b-rate=33600/33600, rbs=0,d-pad=None, retr=1, sq=5, snr=10495, rx/tx chars=286/266, bad=0, rx/txec=16/6, bad=0, time=96, finl-state=Steady Retrain,disc(radius)=(n/a)/(n/a), disc(modem)=1F00 <unknown>/Requested byhost/non-specific host disconnect%MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/1/24,slot/port=5/38, call_id=FD, userid=touraco-e1-4, ip=79.205.24.1,calling=(n/a), called=35170, std=V.34+, prot=LAP-M, comp=V.42bis,init-rx/tx b-rate=33600/33600, finl-rx/tx b-rate=33600/33600, rbs=0,d-pad=None, retr=1, sq=5, snr=10495, rx/tx chars=289/267, bad=0, rx/txec=17/7, bad=0, time=93, finl-state=Steady Retrain,disc(radius)=(n/a)/(n/a), disc(modem)=1F00 <unknown>/Requested byhost/non-specific host disconnect%MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/3/15,slot/port=5/2, call_id=FF, userid=touraco-e1-4, ip=79.200.24.1,calling=(n/a), called=35170, std=V.34+, prot=LAP-M, comp=V.42bis,init-rx/tx b-rate=33600/33600, finl-rx/tx b-rate=33600/33600, rbs=0,d-pad=None, retr=1, sq=5, snr=10495, rx/tx chars=287/270, bad=0, rx/txec=17/7, bad=0, time=92, finl-state=Steady Retrain,disc(radius)=(n/a)/(n/a), disc(modem)=1F00 <unknown>/Requested byhost/non-specific host disconnect%MODEMCALLRECORD-6-PM_TERSE_CALL_RECORD: DS0 slot/contr/chan=4/3/10,slot/port=5...spe country
To specify the country while setting the NextPort DFC parameters (including country code and encoding), use the spe country global configuration command. To set the country code to the default value, use the no form of this command.
spe country {country_name | e1-default}
no spe country {country_name | e1-default}
Syntax Description
Defaults
Disabled
Command Modes
Global configuration
Command History
Usage Guidelines
On the Cisco universal gateway, DS-0 companding law selection is configured for the entire system rather than on individual voice ports. Set spe country to the appropriate country.
If T1s are configured, the default is t1-default; if E1s are configured, the default is e1-default.
The Cisco universal gateway must be in an Idle state (no calls are active) to run the spe country command. All sessions on all modules in all slots must be Idle.
Note
Examples
The command below sets the country code to E1 default.
router(config)# spe country e1-defaultspe download maintenance
To perform download maintenance on Service Processing Elements (SPEs) that are marked for recovery, use the spe download global configuration command. To disable download maintenance on SPEs, use the no form of this command.
spe download maintenance {time hh:mm | stop-time hh:mm | max-spes num-of-spes | window time-period | expired-window {disable | drop-call | reschedule}}
no spe download maintenance {time hh:mm | stop-time hh:mm | max-spes num-of-spes | window time-period | expired-window {drop-call | reschedule}}
Syntax Description
Defaults
Enabled
Command Modes
Global configuration
Command History
12.1(1)XD
This command was introduced on the Cisco AS5400. Together with the spe recovery command, the spe download maintenance command replaces the modem recovery maintenance command introduced in 12.0.
12.1.(3)T
This command was integrated into Cisco IOS Release 12.1(3)T on the Cisco AS5400 and Cisco AS5800.
12.1(5)XM1
This command was introduced on the Cisco AS5350 universal gateway.
12.2(11)T
This command was integrated into Cisco IOS Release 12.2(11)T and support was added for the Cisco AS5350.
Usage Guidelines
The SPE download maintenance activity takes place when SPEs are marked for recovery. The settings are enabled by default. When you want to change the default settings to a desired setting, use the spe download maintenance command parameters to perform SPE download maintenance activity with the specific changes.
Enter the time hh:mm keyword to set a time to start the SPE download maintenance activity. Then enter the stop-time hh:mm keyword to set a time to stop the download maintenance. Next enter the max-spes number keyword to set the number of SPEs for the download maintenance. Then enter the window time-period keyword to set a time period to perform the download maintenance. Finally, enter the expired-window keyword to set actions in the event the SPE download maintenance is not completed in the set window time-period.
The download maintenance activity starts at the set start time and steps through all SPEs that need recovery and the SPEs that need a firmware upgrade. The download maintenance activity starts maintenance on the maximum number of set SPEs for maintenance. The system waits for the window delay time for all the ports on the SPE to become inactive before moving the SPE to the Idle state. Immediately after the SPE moves to Idle state, the system starts to download firmware. If the ports are still in use by the end of window delay time, depending upon the expired-window setting, connections on the SPE ports are shutdown and the firmware is downloaded by choosing the drop-call option, or the firmware download is rescheduled to the next download maintenance time by choosing the reschedule option. This process continues until the number of SPEs under maintenance is below max-spes, or until stop-time (if set), or until all SPEs marked for recovery or upgrade have had their firmware reloaded.
Examples
The following example displays the spe download maintenance with the different keyword parameters:
Router(config)# spe download maintenance time 03:00Router(config)# spe download maintenance stop-time 04:00Router(config)# spe download maintenance max-spes 50Router(config)# spe download maintenance window 30Router(config)# spe download maintenance expired-window rescheduleRelated Commands
spe log-size
To set the buffer size for the port event log, use the spe log-size global configuration command.
spe log-size number
Syntax Description
Defaults
No default behavior or values
Command Modes
Global configuration
Command History
Examples
This example sets the buffer size for the event log at 50.
router(config)# spe log-size 50router(config)#Related Commands
show port digital log
Displays the digital data event log with oldest event first.
show prot modem log
Displays the modem port history event log or modem test log.
spe poll
To set the statistical polling interval, use the spe poll global configuration command.
spe poll {auto | time seconds}
Syntax Description
auto
NextPort only: Async transfer of statistics
time seconds
polling interval. The seconds range is 2-60.
Defaults
Enable for auto.
12 seconds for time.
Command Modes
Global configuration.
Command History
Usage Guidelines
The spe poll command is equivalent to the modem poll MICA modem command.
Examples
The example sets the statistics election to 20 seconds:
Router# spe poll time 20Related Commands
clear counters spe
Clears statistical counters for all types of servers.
clear service counters
modem poll retry
spe recovery
To set an SPE port for recovery, use the spe recovery global configuration command.
spe recovery {port-action {disable | recover | none} | port-threshold num-failures}
Syntax Description
Command Modes
Global configuration
Command History
Usage Guidelines
When an SPE port fails to connect after repeated tries, this is an indication that a problem exists in SPE/firmware. A SPE port in this state is recovered by downloading firmware.
This command moves an SPE port that fails to connect consecutively num-failures (port-threshold) to a state based on (port-action). The port is disabled (disable), and then marked for recovery (recover). Any SPE which has a port marked for recovery is downloaded when the SPE is in IDLE state.
Examples
The following example displays the help entries, which describe the command parameters.
router(config)# spe recovery ?port-action Action to apply on port for recoveryport-threshold # of consecutive failed call attempts on a port to applyport-actionRelated Commands
test port modem back-to-back
To test two specified ports back-to-back and transfer a specified amount of data between the ports, use the test port modem back-to-back EXEC command.
Cisco AS5350 and Cisco AS5400 with NextPort DFC
test port modem back-to-back {slot/port}
Cisco AS5800 with Universal Port DFC
test port modem back-to-back {shelf/slot/port}
Syntax Description
Defaults
No default behavior or values
Command Modes
EXEC
Command History
Usage Guidelines
The test port modem back-to-back command should be performed on different combinations to determine a good port.
Note
Examples
The following example displays a back-to-back test:
Router# test port modem back-to-back 1/1/1Repetitions (of 10-byte packets) [1]:*Mar 02 12:13:51.743:%PM_MODEM_MAINT-5-B2BCONNECT:Modems (2/10) and (3/20) connected inback-to-back test:CONNECT33600/V34/LAP*Mar 02 12:13:52.783:%PM_MODEM_MAINT-5-B2BMODEMS:Modems (3/20) and (2/10) completedback-to-back test:success/packets = 2/2Related Commands
Glossary
