Table 4 Open Bugs in Prime Optical 9.6.3
Bug ID
|
Description
|
CSCtd21907
|
When the auto-acknowledge option is enabled in the control panel and an alarm is raised, the Ack Time Stamp field in the Alarm Browser is left blank.
|
CSCtd40814
|
A timeout occurs when launching the Link table from the CTM domain for a SuperUser.
|
CSCth13333
|
It takes a long time for links to become invalid after marking a number of NEs Out of Service.
|
CSCti05620
|
Cannot change General Timing values on ONS 15454-M2 and ONS 15454-M6 NEs.
|
CSCti05740
|
Cannot change Timing Reference List values on ONS 15454-M2 and ONS 15454-M6 NEs.
|
CSCti13083
|
1-day historical Optical Physical PM data is not plotted in the Graph tab.
|
CSCti22837
|
The NE Explorer displays blank rows on GE-XP Ether ports for DS1/E1 and DS3/E3 tabs.
|
CSCtj58927
|
It takes a long time to open the SVLAN table for a group of NEs.
|
CSCtk17643
|
If you try to add an NE that was previously deleted from CTM, an error message indicates that the IP address already exists.
|
CSCtk48145
|
When you open the Domain Explorer and select a CRS-1 or ONS 15454 NE and then change the selection, the following message is displayed:
Property sheet has been changed. Do you really want to discard changes?
The client hangs with the message Retrieving data, please wait shown in the bottom left corner of the Domain Explorer window.
|
CSCtn16936
|
An EID 333: Database timeout occurred warning appears on the PM table when you request PM on an SDH higher order virtual container at the NE level.
|
CSCto14529
|
The Data Migrator wizard incorrectly allows users to export MGX modules.
|
CSCto50329
|
The Refresh Data button in the real-time PM Graph panel does not work.
|
CSCto86112
|
A GateWay/CORBA error appears when creating OTS links between passive units (MD 40 ODD, MD 40 EVEN, or FLD-4.xx.x) and 80-WXC cards.
|
CSCto96709
|
The GateWay/CORBA SetAdditionalInfo API BFD setting fails if the BFD value is in microseconds.
|
CSCtq29356
|
The Reset To Defaults operation fails for fabric card trunk ports on FEC thresholds. Values are not restored to original default values and no error message appears.
|
CSCtq40320
|
The TP tunnel operational status is not updated.
|
CSCtq57156
|
The Layer 2 Protocols tab under the Ethernet Ports links for PT_10GE_4 and PTSA_GE modules is not updated when the Layer 2 Protocol values are modified by another user.
|
CSCtq75318
|
The GateWay/CORBA CreateFTP API gives a channel group creation error when the following set of parameters is not reported: L2ActionLACP = Forward, enableLACP = true.
|
CSCtq89172
|
VT circuits remain in DISCOVERED (Split) status in the Circuit table.
|
CSCtq91998
|
Ports in use are listed as available in the Channel Group Creation wizard.
|
CSCtq97423
|
A policy map is partially downloaded on a CPT NE when an error states that the download failed.
|
CSCtr12376
|
When you create a channel group and select a channel group ID that is being used by an NE, the operation fails. However, no error message appears to notify you of the failure.
|
CSCtr29018
|
The NE Purge Fail icon does not appear.
|
CSCts00229
|
An EID-333 database timeout error appears in the Alarm Log window.
|
CSCts42329
|
Some CPT system data (for example, Router ID, IP address, and mask) is not updated when the NE database of the CPT is restored. When this occurs, MPLS-TP tunnel creation also fails.
|
CSCts63584
|
A TP tunnel disappears from the Single Service table when you add or remove an LSP.
|
CSCts85295
|
Actions are applied incorrectly after provisioning QoS policy maps on CPT nodes.
|
CSCtt01727
|
Incorrect parameters are highlighted when applying Lockout to TP Tunnel LSP.
|
CSCtt07621
|
The GateWay/CORBA setTCATPParameter and getTCATPParameter APIs do not work with the following layer rates:
2. LR_T1_and_DS1_1_5M
5. LR_E1_2M
|
CSCtt11199
|
It takes a long time to delete a link.
|
CSCtt19615
|
QoS policies are not removed from the Cisco Prime Optical GUI when they are removed via CTC.
|
CSCtt35017
|
When you assign large LSP numbers during TP Tunnel creation, the TP Tunnel is provisioned with random LSP number values.
|
CSCtt99022
|
The Undiscovered Network Elements folder is duplicated under the Lost and Found folder.
|
CSCtu37267
|
When the Circuit table is launched from a slot with partial circuits, some circuits are not displayed.
|
CSCtw49343
|
Prime Optical displays the Ethernet port state for CPT600-37 and CPT600-38 devices in slot 3 as Working and Non_Working, respectively. However, the Common Inventory portlet shows the port state as UNKNOWN.
|
CSCtw72144
|
The GateWay/CORBA getFiberAttributeResponse API does not return fiber number information.
|
CSCtx08179
|
On CPT600 NEs, the Alarm DRY Contacts tab does not work.
|
CSCtx51883
|
Incorrect values are displayed for some parameters on NGXP cards, as follows:
• Min PMD ("0" is displayed instead of "N/A")
•Avg PMD ("0" is displayed instead of "N/A")
•Min OSNR ("-40" is displayed instead of "N/A")
•Avg OSNR ("-40" is displayed, instead of "N/A")
The corresponding PMD and OSNR Max values correctly report N/A.
|
CSCtx76183
|
Auto-sensing cannot be enabled on AR_XP, AR_XPE, and AR_MXP cards.
|
CSCtx80567
|
The following counters on AR_XP/AR_MXP real-time payload PM have an N/A value:
Real SDI_3G_VIDEO payload provisioned:
- gfpStatsRxCRCErrors
- gfpStatsRxSblkCRCErrors
Real ISC3_STP_1G payload provisioned
- gfpStatsCHecRxMBitErrors
- gfpStatsCHecTxMBitErrors
|
CSCtx89275
|
The GetActiveMaintenanceOperation API takes very long.
|
CSCtx91361
|
The getCTPsAndTopologicalLinks API for OCHCC circuits does not return CTP trunk ports.
|
CSCty04341
|
The L2 Link Creation wizard incorrectly allows users to select ports that are already in use.
|
CSCty04478
|
LMP Links between Cisco ONS 15454 NEs and ASR9K NEs are invalid.
|
CSCty13861
|
Prime Optical hangs while deleting or purging NEs.
|
CSCty13950
|
The FOG port type is not shown in the Timing Reference Panel of the NE Explorer for CPT platforms.
|
CSCty13961
|
The FOG number is incorrectly labeled as SLOT in the timing reference list panel of the NE Explorer for CPT platforms.
|
CSCty32780
|
TP Tunnel creation fails when you provide the list of links to be excluded from the protected path.
|
CSCty35656
|
When you are creating an OCHCC on an AR_MXP or AR_XP card configured as a Low Rate TXP_MR 4GFC, the OTN settings are not disabled.
|
CSCty54556
|
The WKG-PW-NOT-FRWD alarm raised on CPT nodes is not listed in the Alarm Type drop-down list when querying for alarms affecting services, because of which it is not displayed in the Service Alarm tab.
|
CSCty58047
|
A wrong routing calculation is made during EVC provisioning if the user provides a node to be excluded in the routing constraints panel.
|
CSCty58180
|
Trunk-to-Filter inter-NE patchcords from AR_XP, AR_XPE, and AR_MXP to WSS filter are duplicated in the Link table.
|
CSCty58378
|
For a node connected to IPv6, the Domain Explorer displays an IPv4 IP address instead of the IPv6 address.
|
CSCty64467
|
An error is reported while trying to set ptsa_50 ports as references for NE timing.
|
CSCty70082
|
The GateWay/CORBA getEMS API returns a negative system.uptime value.
|
CSCty70352
|
Trunk-to-Filter inter-NE patchcords appear invalid and duplicated in the Link table, after they are deleted via CTC while NEs are in the OOS state.
|
CSCty77589
|
Incorrect protection type is displayed for splitter-protected OCHCC circuits on some AR_XP, AR_XPE, and AR_MXP card configurations.
|
CSCty80524
|
The ProvideSync check box in PT System > Timing panel is not aligned even after refreshing data from the NE.
|
CSCtz09492
|
The WK-PW-CC-DOWN alarm is displayed in the Conditions tab even after the alarm is cleared.
|
CSCtz56218
|
On Linux operating systems, the Prime Optical client window cannot be moved to the corner of the screen.
|
CSCua12148
|
OCHCC circuits between 100G-LC cards that should not be promoted to WSON, are incorrectly promoted.
|
CSCua63019
|
TCA notifications are raised even when SIGLOSS and SQUELCHED alarms are active on 10x10G_LC cards.
|
CSCua75296
|
Cannot set Ethernet port parameters on CPT platform after NE re-sync.
|
CSCua76080
|
Changing the value of a parameter back to its default value fails on 10x10G_LC, 100G_LC_C, and CFP_LC cards.
|
CSCua80818
|
It is not possible to add a static route on a node.
|
CSCua93147
|
In a 10GE port of a 10x10_LC card in ONS 15454 network elements, the Line, and Ethernet reports the values GFP, CBR, and TRP. However, it is not possible to sent the values.
|
CSCua93522
|
An incorrect html file is exported to the Cisco Prime Optical client in CFP-TXP configuration with Multishelf NEs.
|
CSCua93840
|
PM data on NEs cannot be retrieved after the first attempt.
|
CSCub02064
|
Users not belonging to Optgrp have permission to execute some files.
|
CSCub08344
|
While trying to delete or purge a large number of NEs, some NEs are not deleted.
|
CSCub16174
|
The undelete operation moves NEs under the root node of the Domain Explorer topology tree and not under the group to which the NE belongs.
|
CSCub19072
|
A CRS network element is not rediscovered if it was previously deleted from Cisco Prime Optical.
|
CSCub29130
|
The server does not respond while attempting to create a circuit, or disconnect from a node.
|
CSCub50221
|
When you configure Prime Optical as a suite component to integrate with Prime Central, the DMIntegrator.sh script fails during integration and displays the following error:
Exception in thread "main" com.cisco.prime.dminventory.model.SubsystemInventoryException:
Subsystem type=opt with comURI=opt://opt:<id> already exists. Remove it before insertion.
|
CSCuc00836
|
An error occurs when the Data Migrator tries to read the export file.
|
CSCuc19526
|
Prime Optical does not allow you to provision protected LO VCAT circuits with split routing option. The following error message is displayed:
EID 1038: Failed to set LO Options
|
CSCuc23883
|
Historical PM data is not collected if the NE time is set to be ahead of the server time.
|
CSCuc46127
|
The PM graph is not plotted.
|
CSCuc58017
|
Some circuits remain in Partial state and do not get updated.
|
CSCuc73059
|
An error message appears after the user clicks the Launch ANS Wizard... button. This occurs when uploading a CTP.xml file to perform an ANS.
|
CSCuc77125
|
A user without permission to manage L1 circuits, can still view L1 circuits.
|
CSCuc81957
|
While creating a circuit using manual routing, the correct direction cannot be set on a link unless the link is clicked four times.
|
CSCuc83581
|
The GateWay/CORBA does not send notifications for protection switch events related to Cisco 15454 NEs.
|
CSCuc83801
|
If the Oracle database is not running when a patch is applied, Prime Optical fails to start.
|
CSCuc83952
|
The Username column of the Audit Log reports "Internal" instead of the username.
|
CSCuc96032
|
Cisco Prime Optical installation fails if the Oracle SID contains an underscore (_), followed by a high numeric value. The following Oracle error is reported:
ORA-03113: end-of-file on communication channel
|
CSCuc98549
|
The Network Map node tree view is not updated after adding badges.
|
CSCud09849
|
By default, Prime Optical displays the following directories and their contents from a web browser:
•http://server/admin
•http://server/ctc
•http://server/ClientBinary
•http://server/log
|
CSCud29013
|
The SONET threshold trunk port values are not restored to their default values for 10x10G_LC cards.
|
CSCud34652
|
When a new circuit is created, the Circuit Report does not notify the user.
|
CSCud38820
|
Cannot create pluggable ports in AR_XP, and AR_MXP in MSTP cards in the branch cpo_cpt_fb for CPT 600 NE with software version - 09.51-012F-15.12-SPA
|
CSCud41204
|
The Attenuator Value column in the Optical Line and Amplified Optical Line tabs is not displayed for MSTP cards.
|
CSCud41223
|
The Pwr OSC Failure column is not displayed for 40_SMR2_C MSTP cards.
|
CSCud41243
|
The Proactive Protection Regen tab is not displayed for OTU2_XP card.
|
CSCud48153
|
Protected SVLAN cannot be created. The following error message is displayed:
EID-1096:Failed to provision the svlan, Sanity check failed on svlan circuit.Too many master
nodes defined in the ring.
|
CSCud50684
|
Non-OTU ports are reported in Real Time OTN PM Query in FANOUT mode.
|
CSCud50791
|
Creating a circuit between two different nodes does not work from the Circuit Report.
|
CSCud64278
|
The wavelength and sides are not displayed in the circuit trace of an STS circuit running on an ADM10G OCHTRAIL.
|
CSCud79439
|
The Prime Optical web server is not accessible when another web server is installed and running.
|
CSCud88078
|
While changing the OCHTRAIL name of a WSON OCHNC circuit that was promoted to OCHCC, the status, service state, and protection type changes.
|
CSCud93384
|
The Equipment Inventory table for an ONS 15310 MA with an ML100T card shows rows in reference to SFPs that do not exist on the card.
|
CSCue06182
|
The Circuit report is not refreshed when launched from the Affected Circuits menu item from the Alarm Browser.
|
CSCue09137
|
Some of the affected circuits are not listed after clicking Affected Circuits from the WSON tab.
|
CSCue21080
|
Perform Protection Switch Operation is disabled in the Link Maintenance report for OCHCC splitter-protected circuits that have different wavelengths between trunk ports.
|
CSCue21112
|
Prime Optical does not display an error message when circuit deletion fails and the status changes to Partial.
|
CSCue28221
|
A general error appears when an OCHNC circuit with an incorrect alien wavelength is promoted to WSON.
|
CSCue30805
|
Duplicate CPTs are reported in the CPTs circuit report for DWDM circuits.
|
CSCue34769
|
You cannot sort the threshold values in the Provisioning > Line > RMON Thresholds tab.
|
CSCue35539
|
The Active User table is not automatically refreshed when auto-refresh is enabled.
|
CSCue52539
|
CPO command soft links under /usr/bin are not created during Prime Optical server installation (standalone mode) when an IP address is used instead of a host name.
|
CSCue54963
|
Optusr users can access alarms on NEs listed in the CPTs circuit report that are not part of their domain.
|
CSCue55025
|
The mouse pointer displays the link creation symbol even after a link is created on the Network Map.
|
CSCue57404
|
The Circuit Creation wizard does not appear when trying to create a circuit from a circuit report.
|
CSCue61701
|
The title of a Circuit report appears blank or incorrect when opened from cards, shelves, or alarms.
|
CSCue62554
|
The Network Map incorrectly indicates a ROADM side.
|
CSCue65417
|
The CLI cannot be launched from ML cards.
|
CSCue65824
|
An OCHCC circuit created with splitter protection (not GMPLS) and two different wavelengths is routed incorrectly. The working and protected paths follow the same route.
|
CSCue66176
|
The OCHTRAIL circuit appears twice in the Link Utilization table.
|
CSCue68181
|
In the Network Map, the link between expanded groups disappears after saving map coordinates.
|
CSCue68203
|
The Alarm and Connection state configuration is not saved in the Global Network Map configuration.
|
CSCue68300
|
Sometimes, Prime Optical continues to zoom in the Network Map and it cannot be stopped.
|
CSCue68485
|
Group disappears after clicking Expand/Collapse Group from the Properties pane.
|
CSCue68630
|
A customized background is not applied to the Parent Map.
|
CSCue68768
|
The Data Migrator export operation fails when there is a high number of TCAs (millions).
|
CSCue70386
|
User cannot set CTC username shorter than 6 characters.
|
CSCue70935
|
Prime Optical uses an incorrect alarm log to check the DB alarm during a Linux HA installation.
|
CSCue70956
|
When a Circuit report is manually refreshed, it does not retrieve the new path of a circuit. Instead, the old path is displayed.
|
CSCue70963
|
The GateWay/CORBA getTP API returns LR_GFP_Multirate on 10x10GLC PTP configured in LOW LATENCY operating mode.
|
CSCue70982
|
For 100G_LC transmission parameters, the GateWay/CORBA getTP API returns an empty value for AlarmReporting.
|
CSCue71154
|
After installing Prime Optical with an embedded Oracle database in an HA Linux environment, DB Flashback is not enabled.
|
CSCue73649
|
On some MSTP nodes, there is no Node or Rack view.
|
CSCue73706
|
The GateWay/CORBA getEquipment API retrieves incorrect client ports for the AR_XPE ODU0 virtual interface.
|
CSCue73765
|
Multiple Operation windows can be opened from the Link Maintenance report.
|
CSCue73790
|
In the Link Maintenance report, a forced switch operation can be cleared by clicking Unlock.
|
CSCue75551
|
You cannot create manual transmission links with OPT_AMP_17C and OPT_AMP_C cards because PTPs are not available for creation.
|
CSCue75677
|
The NE Explorer hangs when attempting to locate faults related to the CP-UNVER-CLEARED alarm.
|
CSCue77032
|
After you provision some CRS parameters, the audit log reports incorrect shelf, slot, and port information within the CM message.
|
CSCue77991
|
Unsupported FEC values are available for selection from the OTN tab of a PLIM 100G card. If an unsupported value is selected, nothing happens, and the previous value appears.
|
CSCue78201
|
Sometimes, Prime Optical displays different CRS PLIM values than that set by the user.
|
CSCue78320
|
When creating a WSON OCHTRAIL circuit, the Proactive Protection parameters in the circuit creation wizard may have incorrect values. Sometimes the retrieved values shown are -1 (OCHTRAIL from TXP to PLIM) see attached snapshot. Other times (PLIM to TXP, PLIM to PLIM) the circuit creation fails leaving ports in service.
|
CSCue78708
|
The Alarm Behavior setting does not work on CFP-LC card GE ports.
|
CSCue78727
|
The NE Explorer is blank and cannot be closed after some provisioning operations.
|
CSCue78784
|
Circuit report does not open for a given alarm. Instead, an error appears in the Java console.
|
CSCue78983
|
The Network Map does not automatically refresh after the state of a link changes.
|
CSCue79023
|
The circuit search and circuit report operations do not work when selecting OTT links from the Network Map.
|
CSCue80942
|
The Network Map hangs after deleting managed NEs.
|
CSCue81232
|
When using a GateWay/CORBA API to delete an OCHTRAIL GMPLS circuit, related ports are left in service state. In that situation, to create a circuit again starting from the same ports, it is mandatory to change the port state directly
|
CSCue81463
|
When auto-refresh is enabled, the Circuit report does not notify when new circuit is created.
|
CSCue81645
|
LMP links involving CRS are not discovered with ONS NEs with version 9.602.
|
CSCue87640
|
There is no data in the L2 Topology table.
|
CSCue89127
|
In the Reroute Wavelength window for WSON circuits, the working path is shown as incomplete. Part of the circuit passing through LMP links shows only one direction.
|
CSCue89519
|
The wrong trunk payload type is shown in the CTPs report when FANOUT mode is configured.
|
CSCue89908
|
Recreating a circuit from the Circuit Report fails under specific conditions.
|
CSCue92245
|
In the Network Map, the link utilization tooltip gets updated as soon as OTS is changed, and does not wait for the polling interval to expire.
|
CSCue92650
|
Circuits remain in partial state after a node is moved out of service and back in service.
|
CSCue92862
|
The SVLAN table hangs while attempting to refresh data.
|
CSCue94609
|
The Proactive Revert alarm from CRS PLIM is incorrectly managed.
|
CSCue95118
|
When the CTPs and Spans reports are open, the Circuit report hangs after receiving certain notifications.
|
CSCue95287
|
From the NE explorer, you cannot create an SDCC on 15310_CL NEs.
|
CSCuf06126
|
While searching for circuits from the Network Map, Prime Optical displays circuits that have been deleted via CTC.
|
Feedback
