Table Of Contents
Release Notes for
Cisco Configuration Professional 2.5
Contents
Introduction
System Requirements
PC System Requirements
Router System Requirements
Supported Routers
Supported Phones
Supported Modules and Cards
Connected Grid
Cisco IOS Releases
Determining the Cisco IOS Release
Required IP Address Configuration Information
Router Configuration Requirements
Cisco CP Ordering Options
New and Changed Information
New and Changed Features
New Hardware Support
Limitations and Restrictions
Cisco CP Minimum Screen Resolution
JRE Settings for Cisco CP
Pop-up Screens Appearing on Primary Monitor if Cisco CP Is Moved to Extended Monitor
Important Notes
Cisco IOS Enforces One-Time Use of Default Credentials
Cisco CP Merge and Replace Configuration Functions Fail Under Some Conditions
Cisco CP May Lose Connection to Network Access Device
Popup Blockers Disable Cisco CP Online Help
Screencasts for Cisco CP Features
Temporary Internet Files—Impact on Launch
Caveats
Resolved Caveats
Open Caveats
Related Documentation
Glossary
Release Notes for
Cisco Configuration Professional 2.5
April 29, 2011
OL-24944-01
These release notes support Cisco Configuration Professional (Cisco CP) version 2.5. They should be used with the documents listed in the "Related Documentation" section.
These release notes are updated as needed. To ensure that you have the latest version of these release notes, go to http://www.cisco.com/go/ciscocp. In the Support box, choose General Information > Release Notes, and then find the latest release notes for your release
Contents
This document contains the following sections:
•
Introduction
•System Requirements
•New and Changed Information
•Limitations and Restrictions
•Important Notes
•Caveats
•Related Documentation
•Glossary
Introduction
Cisco CP is a GUI-based device management tool for Integrated Service Routers. Cisco CP simplifies router, Firewall, Intrusion Prevention System, VPN, Unified Communications, WAN, and basic LAN configurations through GUI-based, easy-to-use wizards. Cisco CP is installed on a PC.
Routers that are ordered with Cisco CP are shipped with Cisco CP Express installed in router flash memory. Cisco CP Express is a light-weight version of Cisco CP that you can use to configure LAN and WAN interfaces.
System Requirements
This sections describes PC and router system requirements. It contains the following parts:
•PC System Requirements
•Router System Requirements
•Cisco CP Ordering Options
PC System Requirements
Table 1 lists the system requirements for a PC running Cisco CP. Although the Cisco CP application requires Java Runtime Environment (JRE) to run, the Cisco CP Express application included with Cisco CP can run under the native Java Virtual Machine in the supported browsers and JRE.
Table 1 PC System Requirements
System Component
|
Requirement
|
Processor
|
2 GHz processor or faster
|
Random Access Memory
|
1 GB DRAM minimum; 2 GB recommended
|
Hard disk available memory
|
400 MB
|
Operating System
|
Any of the following:
•Microsoft Windows 7-32 and 64 bit
•Microsoft Windows Vista Business Edition
•Microsoft Windows Vista Ultimate Edition
•Microsoft Windows XP with Service Pack 3-32 bit
•Mac OSX 10.5.6 running Windows XP using VMWare 2.0
|
Browser
|
Internet Explorer 6.0 or above
|
Screen Resolution
|
1024 X 768
|
Java Runtime Environment
|
JRE versions 1.6.0_11 up to 1.6.0_24 supported
|
Adobe Flash Player
|
Version 10.0 or later, with Debug set to "No"
|
Router System Requirements
Router System Requirements are described in the following parts:
•Supported Routers
•Supported Phones
•Supported Modules and Cards
•Connected Grid
•Determining the Cisco IOS Release
•Required IP Address Configuration Information
•Router Configuration Requirements
Supported Routers
Table 2 lists the routers that Cisco CP supports.
Table 2 Supported Routers
Supported Routers
|
Cisco 815 Series
|
CISCO815
CISCO815-VPN-K9
|
Cisco 851 Series
|
CISCO851-K9
CISCO851W-G-A-K9
CISCO851W-G-E-K9
CISCO851W-G-J-K9
|
Cisco 857 Series
|
CISCO857-K9
CISCO857W-G-A-K9
CISCO857W-G-E-K9
|
Cisco 861 Series
|
CISCO861-K9
CISCO861W-GN-A-K9
CISCO861W-GN-E-K9
CISCO861W-GN-P-K9
|
Cisco 867 Series
|
CISCO867-K9
CISCO867VA-K9
CISCO867W-GN-A-K9
CISCO867W-GN-E-K9
|
Cisco 871 Series
|
CISCO871-K9
CISCO871W-G-A-K9
CISCO871W-G-E-K9
CISCO871W-G-J-K9
|
Cisco 876 Series
|
CISCO876-K9
CISCO876W-G-E-K9
|
Cisco 877 Series
|
CISCO877-K9
CISCO877-M-K9
CISCO877W-G-A-K9
CISCO877W-G-E-K9
CISCO877W-G-E-M-K9
|
Cisco 878 Series
|
CISCO878-K9
CISCO878W-G-A-K9
CISCO878W-G-E-K9
|
Cisco 881 Series
|
CISCO881-K9
CISCO881W-GN-A-K9
CISCO881W-GN-E-K9
CISCO881W-GN-P-K9
CISCO881W-A-K9
CISCO881W-E-K9
CISCO881G-K9
CISCO881GW-GN-A-K9
CISCO881GW-GN-E-K9
CISCO881G-S-K9
CISCO881G-V-K9
CISCO881G-A-K9
C881G-U-K9
C881G-S-K9
C881G-V-K9
C881G-B-K9
C881G+7-K9
C881G+7-A-K9
C881SRST-K9
C881SRSTW-GN-A-K9
C881SRSTW-GN-E-K9
|
Cisco 886 Series
|
CISCO886-K9
CISCO886G-K9
CISCO886VA-K9
C886VA-W-E-K9
C886VAG+7-K9
CISCO886GW-GN-E-K9
|
Cisco 887 Series
|
CISCO887-K9
CISCO887VA-K9
CISCO887VA-M-K9
C887VA-W-A-K9
C887VA-W-E-K9
C887VAM-W-E-K9
C887VAG-S-K9
C887VAG+7-K9
C887VAMG+7-K9
CISCO887W-GN-A-K9
CISCO887W-GN-E-K9
CISCO887M-K9
CISCO887MW-GN-E-K9
CISCO887G-K9
CISCO887GW-GN-A-K9
CISCO887GW-GN-E-K9
CISCO887V-K9
CISCO887VW-GNA-K9
CISCO887VW-GNE-K9
CISCO887VG-K9
CISCO887VGW-GNA-K9
CISCO887VGW-GNE-K9
|
Cisco 888 Series
|
CISCO888-K9
CISCO888W-GN-A-K9
CISCO888W-GN-E-K9
CISCO888E-K9
CISCO888EW-GN-A-K9
CISCO888EW-GN-E-K9
CISCO888G-K9
CISCO888GW-G-NA-K9
CISCO888GW-G-NE-K9
C888EG+7-K9
C888SRST-K9
C888SRSTW-GN-A-K9
C888SRSTW-GN-E-K9
|
Cisco 891 Series
|
CISCO891-K9
CISCO891W-AGN-A-K9
CISCO891W-AGN-N-K9
|
Cisco 892 Series
|
CISCO892-K9
CISCO892F-K9
CISCO892W-AGN-E-K9
|
Cisco 1801
|
CISCO1801
CISCO1801/K9
CISCO1801-M
CISCO1801-M/K9
CISCO1801W-AG-B/K9
CISCO1801W-AG-C/K9
CISCO1801W-AG-N/K9
CISCO1801WM-AGB/K9
|
Cisco 1802
|
CISCO1802
CISCO1802/K9
|
Cisco 1803
|
CISCO1803/K9
CISCO1803W-AG-B/K9
CISCO1803W-AG-E/K9
|
Cisco 1805
|
CISCO1805-D
CISCO1805-D/K9
CISCO1805-EJ
|
Cisco 1811
|
CISCO1811/K9
CISCO1811W-AG-B/K9
CISCO1811W-AG-C/K9
CISCO1811W-AG-N/K9
|
Cisco 1812
|
CISCO1812/K9
CISCO1812-J/K9
CISCO1812 W-AG-C/K9
CISCO1812W-AG-P/K9
|
Cisco 1841
|
CISCO1841
|
Cisco 1861
|
CISCO1861-SRST-B/K9
CISCO1861-SRST-C-B/K9
CISCO1861-SRST-C-F/K9
CISCO1861-SRST-F/K9
CISCO1861-UC-2BRI-K9
CISCO1861-UC-4FXO-K9
CISCO1861E-SRST-B/K9
CISCO1861E-SRST-C-B/K9
CISCO1861E-SRST-C-F/K9
CISCO1861E-SRST-F/K9
CISCO1861E-UC-2BRI-K9
CISCO1861E-UC-4FXO-K9
CISCO1861W-SRST-C-B/K9
CISCO1861W-SRST-C-F/K9
CISCO1861W-SRST-B/K9
CISCO1861W-SRST-F/K9
CISCO1861W-UC-2BRI-K9
CISCO1861W-UC-4FXO-K9
|
Cisco 1921
|
CISCO1921/K9
|
Cisco 1941
|
CISCO1941/K9
CISCO1941W-A/K9
CISCO1941W-C/K9
CISCO1941W-E/K9
CISCO1941W-N/K9
CISCO1941W-P/K9
|
Cisco 2800 Series
|
CISCO2801
CISCO2811
CISCO2821
CISCO2851
|
Cisco 2900 Series
|
CISCO2901/K9
CISCO2911/K9
CISCO2921/K9
CISCO2951/K9
|
Cisco 3800 Series
|
CISCO3825
CISCO3825-NOVPN
CISCO3845
CISCO3845-NOVPN
|
Cisco 3900 Series
|
CISCO3925/K9
CISCO3925E/K9
CISCO3945/K9
CISCO3945E/K9
|
Supported Phones
Table 3 lists the phones that Cisco CP supports.
Table 3 Supported Phones
Supported Phones
|
Supported Expansion Modules
|
Supported Conference Stations
|
3905
6901
6911
6921
6941
6945
6961
|
|
|
7902G
7905
7906G
7910G
7911G
7912G
7920
7921G
7931G
|
7914
7915-12
7915-24
7916-12
7916-24
|
7935
7936
7937G
|
7940G
7941G
7941G-GE
7942G
7945G
|
|
|
7960G - compatible expansion module (7914)
7961G - compatible expansion module(7914)
7961G-GE
7962G - compatible expansion module(7915,7916)
7965G - compatible expansion module (7915,7916)
7970G - compatible expansion module (7914)
7971G - compatible expansion module (7914)
7975G - compatible expansion module (7915,7916)
7985G
|
|
|
8941
8945
8961
|
|
|
9951
9971
|
|
|
ATA
CIPC - Cisco IP Communicator
|
|
|
Supported Modules and Cards
Table 4 lists the network modules and interface cards that Cisco CP supports.
Table 4 Supported Modules and Cards
Modules and Cards
|
Advanced Integration
|
AIM-CUE
AIM2-CUE-K9
AIM-IPS-K9
AIM2-APPRE-104-K9
AIM-VPN/BP II PLUS
AIM-VPN/EP II PLUS
AIM-VPN/HP II PLUS
AIM-VPN/SSL-1
AIM-VPN/SSL-2
AIM-VPN/SSL-3
|
Analog Dialup
|
WIC-1AM
WIC-2AM
|
Analog and Digital Voice/Fax
|
NM-HD-1V
NM-HD-2V
NM-HD-2VE
NM-HDA-4FXS
NM-HDV2
NM-HDV2-1T1/E1
NM-HDV2-2T1/E1
EVM-HD-8FXS/DID
EM-HDA-8FXS
EM-HDA-4FXO
EM-HDA-6FXO
EM-HDA-3FXS/4FXO
EM-4BRI-NT/TE
EM2-HDA-4FXO
EM3-HDA-8FXS/DID
|
Application
|
ISM-SRE-300-K9
SM-SRE-700-K9
SM-SRE-900-K9
NME-WAE-302-K9
NME-WAE-502-K9
NME-WAE-522-K9
NME-APPRE -302-K9
NME-APPRE -502-K9
NME-APPRE -522-K9
|
Broadband
|
EHWIC-VA-DSL-A
EHWIC-VA-DSL-B
EHWIC-VA-DSL-M
HWIC-1ADSL
HWIC-1ADSLI
HWIC-1ADSL-M
HWIC-1CABLE-D-2
HWIC-1CABLE-E/J-2
HWIC-1VDSL
HWIC-2SHDSL
HWIC-4SHDSL
HWIC-4SHDSL-E
HWIC-ADSL-B/ST
HWIC-ADSLI-B/ST
WIC-1SHDSL-V2
WIC-1SHDSL-V3
WIC-1ADSL
WIC 1ADSL-DG
WIC 1ADSL-I-DG
|
Cisco Unity Voicemail
|
NME-CUE
NM-CUE
NM-CUE-EC
|
Ethernet Routed Port
|
HWIC-1FE
HWIC-2FE
|
Ethernet Switch
|
NM-16ESW
NM-16ESW-PWR
NM-16ESW-1GIG
NM-16ESW-PWR-1GIG
NMD-36ESW-PWR
NMD-36ESW-PWR-2GIG
NME-16ES-1G-P
NME-X-23ES-1G-P
NME-XD-24ES-1S-P
NME-XD-48ES-2S-P
SM-ES2-16-P
SM-ES2-24
SM-ES2-24-P
SM-D-ES2-48
SM-ES3-16-P
SM-ES3-24-P
SM-ES3G-16-P
SM-ES3G-24-P
SM-D-ES3-48-P
SM-D-ES3G-48-P
EHWIC-4ESG
EHWIC-4ESG-P
EHWIC-D-8ESG
EHWIC-D-8ESG-P
HWIC-4ESW
HWIC-4ESW-POE
HWIC-D-9ESW
HWIC-D-9ESW-POE
|
ISDN BRI
|
WIC-1B-S/T-V3
|
Multiflex Trunk Voice & WAN Interface Cards
|
VWIC2-1MFT-T1/E1
VWIC2-2MFT-T1/E1
|
Serial Sync/Async Interface
|
HWIC-16A
|
HWIC-2A/S
HWIC-4A/S
HWIC-8A
HWIC-8A/S-232
WIC-2A/S
|
Serial WAN Interface
|
HWIC-1T
HWIC-2T
HWIC-4T
HWIC-1DSU-T1
WIC-1T
WIC-2T
WIC-1DSU-T1-V2
WIC-1DSU-56K4
|
Voice Interface
|
VIC-2DID
VIC-4FXS/DID
VIC2-2FXO
VIC2-4FXO
VIC2-2FXS
VIC2-2BRI-NT/TE
VIC2-2E/M
VIC3-4FXS/DID
VIC3-2FXS/DID
VIC3-2FXS-EDID
|
VPN and Security
|
NME-IPS-K9
NME-NAC-K9
|
Wireless AP
|
HWIC-AP-G-A
HWIC-AP-G-E
HWIC-AP-G-J
HWIC-AP-AG-A
HWIC-AP-AG-E
HWIC-AP-AG-J
|
Wireless WAN
|
EHWIC-3G-EVDO-B
EHWIC-3G-EVDO-S
EHWIC-3G-EVDO-V
EHWIC-3G-HSPA-U
HWIC-3G-CDMA-S
HWIC-3G-CDMA-V
HWIC-3G-HSPA
HWIC-3G-HSPA-A
HWIC-3G-HSPA-G
HWIC-3G-GSM
PCEX-3G-HSPA-G
PCEX-3G-HSPA-US
|
Connected Grid
Table 5 lists the connected grid devices that Cisco CP supports.
Table 5 Connected Grid
Switches
|
Routers
|
CGS-2520-24TC
CGS-2520-16S-8PC
|
CGR 2010/K9
|
Cisco IOS Releases
Cisco CP is compatible with the Cisco IOS releases listed in Table 6.
Table 6 Cisco CP-Supported Routers and Cisco IOS Versions
Router Model
|
Minimum Cisco CP-Supported Cisco IOS Versions
|
Cisco 815
|
12.4(11)T
|
Cisco 850 series
|
12.4(9)T
|
Cisco 861
|
12.4(20)T
|
Cisco 867
|
15.0(1)M
|
Cisco 870 series
|
12.4(9)T
|
Cisco 881
|
12.4(20)T
|
Cisco 886
|
15.0(1)M
|
Cisco 887
|
15.0(1)M
|
Cisco 888
|
12.4(20)T
|
Cisco 890 series
|
15.0(1)M
|
Cisco 1801
Cisco 1802
Cisco 1803
|
12.4(9)T
|
Cisco 1805
|
12.4(15)XY
|
Cisco 1811
Cisco 1812
|
12.4(9)T
|
Cisco 1841
|
12.4(9)T
|
Cisco 1861
|
12.4(20)T
|
Cisco 1941
Cisco 1941W
|
15.0(1)M
|
Cisco 2800 series
|
12.4(9)T
|
Cisco 2900 series
|
15.0(1)M
|
Cisco 3800 series
|
12.4(9)T
|
Cisco 3900 series
|
15.0(1)M
|
Determining the Cisco IOS Release
To determine the release of Cisco IOS software currently running on your Cisco router, log into the router and enter the show version EXEC command. The following sample output from the show version command indicates the Cisco IOS release on the second output line:
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(2)T1"
Required IP Address Configuration Information
Table 7 provides the required IP address configuration for the PC. Use this information to complete the "Task 4: Configure the IP Address On the PC" section in Cisco Configuration Professional Quick Start Guide.
Table 7 Required PC IP Address Configurations
Router Model
|
DHCP Server
|
Required PC IP Address Configuration
|
Cisco 815, Cisco 85x, Cisco 86x, Cisco 87x, Cisco 88x, Cisco 89x, Cisco 180x, Cisco 1805, Cisco 1811 and 1812
|
Yes
|
Obtains the IP address automatically
|
Cisco 1841, Cisco 1861, Cisco 28xx, Cisco 38xx, Cisco 29xx, Cisco 39xx
|
No
|
Static IP address from 10.10.10.2 to 10.10.10.6
Subnet Mask: 255.255.255.248
|
Router Configuration Requirements
To run Cisco CP, a router configuration must meet the requirements shown in Table 8.
Table 8 Router Configuration Requirements
Feature
|
Requirement
|
Configuration Example
|
Secure access
|
SSH and HTTPS
|
Router(config)# ip http secure-server
Router(config)# ip http authentication local
Router(config)# line vty 0 15
Router(config)# login local
Router(config-line)# transport input ssh
Router(config-line)# transport output ssh
|
Nonsecure access
|
Telnet and HTTP
|
Router(config)# ip http server
Router(config)# ip http authentication local
Router(config)# line vty 0 15
Router(config)# login local
Router(config-line)# transport input telnet
Router(config-line)# transport output telnet
|
User privilege level
|
15
|
Router(config)# username cisco privilege 15 secret 0 cisco
|
The default configuration file meets all Cisco CP requirements. The default configuration file has the name cpconfig-model_number.cfg. For example, the configuration file for the Cisco 860 and Cisco 880 routers is cpconfig-8xx.cfg.
Cisco CP Ordering Options
Table 9 describes the ordering options under which Cisco CP can be ordered. Cisco CP Express is a product that is shipped in router flash memory when the router is ordered with Cisco CP.
Table 9 Cisco CP Ordering Options
Ordering Options
|
Description
|
ISR-CCP-CD
|
Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in NVRAM
|
ISR-CCP-CD-NOCONF
|
Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory
|
ISR-CCP-EXP
|
Cisco CP: Not shipped
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in NVRAM
|
ISR-CCP-EXP-NOCONF
|
Cisco CP: Not shipped
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory
|
ISR-CCP-CD=
|
Cisco CP: Shipped on CD
Spare SKU: Mapped to ISR-CCP-CD
|
New and Changed Information
This section contains new information about Cisco CP and any information about Cisco CP that has changed.
This section contains the following parts:
•New and Changed Features
•New Hardware Support
New and Changed Features
Cisco CP 2.5 supports the following new and changed features:
• Bulk Import Enhancements
A newer Version (1_1) of the Bulk Import template is available. The new template supports creation of SIP phones, extensions, and users along with the SCCP counterparts. However, the older version of the template is still supported.
•Licensing Feature Support
Using Cisco CP, you can:
–Install and enable licenses.
–View licenses present on the device.
•ModBus
The Modicon Communication Bus (ModBus) feature allows communication between a switch and a device in the network by using the ModBus client software. ModBus is a serial communications protocol for client-server communication between a switch (server) and a device in the network running ModBus client software (client). You can use ModBus to connect a computer to a Remote Terminal Unit (RTU) in Supervisory Control and Data Acquisition (SCADA) systems.
•Phone and Extension Templates Enhancements
In addition to Softkeys, Cisco CP now supports Blocked Features, Call Conference, and Codec configurations on Phone Templates. You can now also configure Permissions and Translation Rules and Profiles on Extension Templates, in addition to Call Forward and Pickup Group Number.
•Phone Firmware Enhancements
A wizard is now available to configure phone firmware files for both SIP and SCCP phone models available on the Flash or on the PC in .zip or .tar formats. You can download phone firmware files using the Download link. The phone firmware summary page lists configured phone firmware and also allows you to view phone registration status, edit or delete phone firmware configurations, and reset phones to allow configuration of new phone firmware.
•Ping and Traceroute
Cisco CP now supports the ping and traceroute commands from the Utilities menu to enable troubleshooting of the network.
•Quick Search
Cisco CP now provides option to search for features based on keywords and navigate to the required feature.
•Service Ready Engine—Virtualization Support (SRE-V)
Using Cisco CP, you can:
–Install SRE-V software on SM-SRE 700 and 900 modules.
–Edit console manager and hypervisor IP configurations.
–Launch Vsphere client UI from Cisco CP.
–Configure users, groups, roles and permissions, and syslog
–View license details.
•Security Wizard
The security wizard feature enables you to create an Access Control List (ACL) and assign it to the list of interfaces. It also prevents unauthorized users (host) from accessing a specific server (destination) or a specific network (destination), as well as a specific protocol on the application server.
•Setup New Device
The Setup New Device wizard allows you to set up a new device and manage it. Before you use Cisco CP to set up a new device, ensure that the computer running Cisco CP is connected to the powered up device over the console port and the device baud is set to its default value.
•Single-Number Reach Enhancements
The Single-Number Reach (SNR) enhancement allows you to replace the calling-number with the SNR extension number, in calls forwarded to the remote phone. This feature helps disguise the actual caller number by replacing it with the SNR extension number, making it possible for the receiver of the call to identify whether the call is a direct one or through the SNR number.
•SIP Support
Cisco CP now supports:
–Creation and modification of SIP extensions and phones for SIP CME, SCCP, and SIP CME through SIP trunks.
–Registration of SIP phones.
–Option to quickly add new SCCP and SIP phones and extensions and edit values.
•Telephony Settings Enhancements
Telephony Settings allows you to specify the endpoint type as SIP or SCCP. Advanced Telephony Settings options are now available from the Unified Communications > Telephony Settings screen.
•Ten Devices Per Community
Cisco CP now supports ten devices per community.
•Traffic Monitoring
Using Cisco CP, you can:
–Install Data Collector and enable traffic monitoring.
–View real-time bandwidth usage and throughput.
–View traffic volume grouped by protocol and IP address.
•Unified Communications Enhancements
Cisco Unified Border Element (CUBE) and Media Resources are now available as separate modes under Unified Communications > Unified Communications Features. All Unified Communications screens now open with a read-only summary screen. The features available in the left navigation pane depend on the mode you select in the Unified Communications Features page.
•WAAS Express Registration
Cisco CP 2.5 provides a wizard to simplify the registration of WAAS Express with the WAAS Central Manager (WCM). Using the wizard you can configure:
–WCM IP address
–WCM Certificate
–Router's self-signed certificate
–Local User
–AAA Authentication List
New Hardware Support
The new devices supported are:
•CISCO887VA-K9
•CISCO881G+7-A-K9
•CISCO881G+7-K9
•CISCO881G-B-K9
•CISCO881G-S-K9
•CISCO881G-U-K9
•CISCO881G-V-K9
•CISCO881W-A-K9
•CISCO881W-E-K9
•CISCO886VAG+7-K9
•CISCO886VA-W-E-K9
•CISCO887VAM-W-E-K9
•CISCO887VAG+7-K9
•CISCO887VAG-S-K9
•CISCO887VAMG+7-K9
•CISCO887VA-W-A-K9
•CISCO887VA-W-E-K9
•CISCO888EG+7-K9
•EHWIC-VA-DSL-A
•EHWIC-3G-HSPA-U
•EHWIC-3G-EVDO-V
•EHWIC-3G-EVDO-S
•EHWIC-VA-DSL-B
•EHWIC-VA-DSL-M
Limitations and Restrictions
This section describes restrictions and limitations that may apply to Cisco CP. It contains the following parts:
•Cisco CP Minimum Screen Resolution
•JRE Settings for Cisco CP
•Pop-up Screens Appearing on Primary Monitor if Cisco CP Is Moved to Extended Monitor
Cisco CP Minimum Screen Resolution
Cisco CP requires a screen resolution of at least 1024 x 768.
JRE Settings for Cisco CP
The following JRE settings are needed for Cisco CP to function properly:
Step 1 Go to Start > Control Panel > Java.
Step 2 Click View under Java Applet Runtime Settings.
Step 3 Select your JRE in use.
Step 4 Set the "Java runtime parameters" with the value "-Xmx256m -Dsun.java2d.d3d=false".
In addition, if JRE is upgraded to versions 1.6.0_11 or above, following settings are needed after Cisco CP installation.
Step 1 Go to Start > Control Panel > Java > Advance.
Step 2 Select "Java Plug-in" tree.
Step 3 Uncheck the check box for Enable next-generation Java Plug-in.
Step 4 Restart Cisco CP.
Pop-up Screens Appearing on Primary Monitor if Cisco CP Is Moved to Extended Monitor
If Cisco CP is running on a laptop that is also connected to an external monitor and the screen is set for extended display, pop-up dialog boxes of all SDM applet security pages, routing pages, and help pages appear on the primary monitor. This issue is seen in the following scenario:
Step 1 Connect the monitor to a laptop and set the screen for extended display.
Step 2 Launch Cisco CP and move it to secondary screen.
Step 3 Click Configure > Security > Security Audit > Perform Security Audit.
The Audit screen appears in the primary monitor and Cisco CP in the secondary monitor.
Important Notes
This section contains important information for Cisco CP. It contains the following sections:
•Cisco IOS Enforces One-Time Use of Default Credentials
•Cisco CP Merge and Replace Configuration Functions Fail Under Some Conditions
•Cisco CP May Lose Connection to Network Access Device
•Popup Blockers Disable Cisco CP Online Help
•Screencasts for Cisco CP Features
•Temporary Internet Files—Impact on Launch
Cisco IOS Enforces One-Time Use of Default Credentials
To address CSCsm25466, Cisco IOS images included with recent shipments of Cisco 800, Cisco 1800, Cisco 2800, Cisco 2900, Cisco 3800 and Cisco 3900 routers, enforce the one-time use of the default user name and password provided in the Cisco CP configuration file. If you bypass Cisco CP or Cisco CP Express and use a console or Telnet connection to log into the router, the login and exec banners warn you that you must change the user name to "cisco" and the password to "cisco" before you log off the router. If you do not change the credentials as directed, you will not be able to log into the router the next time that you attempt to do so.
The following Cisco IOS releases enforce the one-time use of the default credentials:
•12.4(11)T or later
•12.4(11)SW, 12.4(11)SW1, 12.4(11)XV, 12.4(11)XJ
•12.4(9)T5, 12.4(9)T6
•15.0(1)M or later
Follow the procedure in this section to secure the router by creating a new username and password, to remove the login banner and exec banner warnings, and to save the configuration changes to the router startup configuration.
Note If you log into the router using a Telnet or a console connection but do not complete the steps in this procedure, be aware of the following:
•If you do not change the default username and password, and then log off the router, you will not be able to log into the router again without entering the reload command. No additional warning is given before you log off.
•If you do not change the default username and password, but do enter the write memory command before ending the session, future logins will be disabled. In this case, you will need to follow the password recovery procedure at the following link:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1831/products_tech_note09186a00801746e6. shtml
To secure the router, remove the banner warnings and save the changes to the router startup config, complete the following steps:
Step 1 Connect the blue console port on your router to a serial port on your PC using the light blue console cable, included with your router. Refer to your router's hardware installation guide for instructions.
Step 2 Connect the power supply to your router, plug the power supply into a power outlet, and turn on your router. Refer to your router's quick start guide for instructions.
Step 3 Use HyperTerminal or a similar terminal emulation program on your PC, with the terminal emulation settings of 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control, to connect to your router.
Step 4 When prompted, enter the username cisco, and password cisco.
Step 5 Enter configuration mode by entering the following command:
yourname# configure terminal
Create a new username and password by entering the following command:
yourname(config)# username username privilege 15 secret 0 password
Replace username and password with the username and password that you want to use.
Step 6 Remove the default username and password by entering the following command:
yourname(config)# no username cisco
Step 7 To remove the login banner, enter the following command:
yourname(config)# no banner login
The login banner warning will no longer appear.
Step 8 To remove the exec banner, enter the following command:
yourname(config)# no banner exec
The exec banner warning will no longer appear.
Step 9 Leave configuration mode, by entering the following command:
Step 10 Copy the configuration changes to the startup configuration by entering the following command:
yourname# copy running-config startup-config
When logging into the router in the future, use the username and password that you created in Step 6.
Cisco CP Merge and Replace Configuration Functions Fail Under Some Conditions
The problem described here is caveat CSCsj21989. If you attempt to merge configuration changes made using the Cisco CP Config Editor feature, or replace the running configuration with a configuration from the Config Editor, the router configuration will not be changed if there is a network device with a Network Address Translation (NAT) IP address, or a cache engine in the connection between the PC and the router. If you need to make changes to the router configuration that you would normally make using the Cisco CP Config Editor, use the Cisco IOS CLI instead.Cisco CP Security Dashboard May Display Threats Unrelated to Your Cisco IOS IPS Installation
Some (or all) of the top threats you obtain using the Cisco CP Security Dashboard may not pertain to your Cisco IOS IPS installation. After you deploy the signatures applicable to the top threats displayed by the Cisco CP Security Dashboard, the dashboard may still display some (or all) top threats with a red icon because applicable signatures could not be found. Those remaining top threats are unrelated to your Cisco IOS IPS installation and are not a danger to your router running Cisco IOS software.
Cisco CP May Lose Connection to Network Access Device
This note concerns the Network Admission Control (NAC) feature.
If the PC used to invoke Cisco CP returns a posture state (Healthy, Infected, Checkup, Quarantine, or Unknown) and if the group policy on the ACS server attached to the posture token assigned to the PC has a redirect URL configured, the connection between Cisco CP and the router acting as the Network Access Device (NAD) may be lost. The same problem can occur if an exception list entry attached to a policy with a redirect URL is configured with the IP address or MAC address of the PC.
If you try to reinvoke Cisco CP from this type of PC, you will not be able to do so because the browser will be redirected to the location specified in the redirect URL.
There are two workarounds for this problem:
•Ensure that the PC that you use to invoke Cisco CP attains a posture token that has an associated group policy on the ACS server that is not configured with a redirect URL.
•Alternatively, use Cisco CP to create a NAC exception list entry with the IP address or MAC address of the PC you use to invoke Cisco CP. Note that the exception list entry created for the PC should be associated to an exception policy that does not have a redirect URL configured in it.
For more information, see the links on the Cisco CP NAC online help pages.
Popup Blockers Disable Cisco CP Online Help
If you have enabled popup blockers in the browser you use to run Cisco CP, online help will not appear when you click the help button. To prevent this from happening, you must disable the popup blocker when you run Cisco CP. Popup blockers may be enabled in search engine toolbars, or may be standalone applications integrated with the web browser.
Microsoft Windows XP with Service Pack 2 blocks popups by default. To turn off popup blocking in Internet Explorer, go to Tools > Pop-up Blocker > Turn Off Pop-up Blocker.
If you have not installed and enabled third-party pop up blockers, go to Tools > Internet Options > Privacy, and uncheck the Block popups checkbox.
Screencasts for Cisco CP Features
Instead of online help, screencasts have been provided for the following Cisco CP 2.5 features:
•Cellular WAN
•Telephony Settings
•Extension Templates
•Licensing
•Module Configuration
•Traffic Monitoring
These screencasts are located at: http://www.cisco.com/en/US/docs/net_mgmt/cisco_configuration_professional/scrcst/ccpsc.html
You must have Internet access to view the screencasts.
Temporary Internet Files—Impact on Launch
Because of Microsoft Windows Java caching issues, Cisco CP is sometimes unable to complete discovery of a device. To fix this issue, complete the following steps:
Step 1 Choose Application > Exit to shut down Cisco CP.
Step 2 Close all existing Internet Explorer windows.
Step 3 Go to Start > Control Panel > Java. The General tab is displayed.
Step 4 In the Temporary Internet Files box, click Delete Files.
Step 5 In the displayed dialog, leave all file types checked, and click OK.
Step 6 Click OK in the Java control panel to close it.
Step 7 Restart Cisco CP.
Caveats
Caveats describe unexpected behavior in Cisco CP. This section contains the following:
•Resolved Caveats
•Open Caveats
Resolved Caveats
Table 10 lists caveats that are resolved in Cisco CP 2.5.
Table 10 Resolved Caveats in Cisco CP 2.5
Bug ID
|
Summary
|
CSCtj84620
|
Cisco CP shows the IPSEC tunnel status instead of DMVPN tunnel status.
|
Open Caveats
Table 11 lists caveats that are open in Cisco CP 2.5.
Table 11 Open Caveats in Cisco CP 2.5
Bug ID
|
Summary
|
Additional Information
|
CSCtn10418
|
Cisco CP Stuck at discovery.
|
Symptom Devices get stuck in the discovering state.
|
| |
|
Conditions This issue occurs when you select multiple devices for discovery, but it is rarely seen. Generally device discovery completes within 5 minutes though there can be some delay over a slow link.
Workaround If the discovery does not complete within 10 minutes, relaunch Cisco CP and rediscover the devices.
|
CSCto88259
|
GenericJDBCException seen while launching Cisco CP.
|
Symptom The following error is seen during launch of Cisco CP:
org.hibernate.exception.GenericJDBCException: Cannot open
connection
Conditions This problem rarely occurs and there are no specific steps which create the problem. Database corruption can cause it.
Workaround Reinstall Cisco CP.
|
CSCto13265
|
Site-to-site VPN displays duplicate tunnel entry.
|
Symptom Cisco CP displays duplicate entries for GREoIPSEC VPN in
the summary screen.
Conditions Duplicate entries are seen when more than one GREoIPSEC tunnel is configured on the router.
Workaround There is no workaround.
|
CSCtn10781
|
Overlaid extensions do not follow the order you specified.
|
Symptom
•Case 1—When selecting multiple extensions to be overlaid on a button, the order of extensions is not the same as specified by you.
•Case 2—The display name is overwritten when the extension is part of an overlay group.
Conditions
•Case 1—This occurs when you select multiple extensions to be overlaid on a phone button.
•Case 2—This occurs when the same extension is overlaid on multiple phones.
Workaround There is no workaround. If you require a particular order or display name, you can configure it through the CLI.
|
CSCtn58565
|
Auto-line command does not work for phones.
|
Symptom When editing a phone, the auto-line incoming command does
not run.
Conditions This problem occurs when editing a phone to set Auto Line Selection to Incoming.
Workaround There is no workaround. Manually configure the auto-line incoming command under an ephone.
|
CSCto70309
|
Unified Communications mode is displayed as CUBE when the mode border-element command is not configured.
|
Symptom On an ISR-G2, if the mode border-element command is not
configured under voice service voip and if telephony service and
max-dn commands are configured, Cisco CP displays the Unified
Communications feature as CUBE.
Conditions This problem occurs only on an ISR-G2 if the mode border-element is not configured and if max-dn is configured under the telephony-service command.
Workaround Select the appropriate mode in the Unified Communications Features screen and deliver the CLI.
|
CSCtn98336
|
Reset to default in Unified Communications Features does not clear some configurations.
|
Symptom The Reset to Default option in the Unified Communications
Features screen does not remove some of the configurations from the
router.
Conditions This problem is seen when you configure the Gateway option via Cisco CP and then select Reset to Default. The Universal and Security Transcoding Dspfarm profile in the gateway configuration is not removed from the router.
Workaround Remove the configuration through the CLI.
|
CSCto67064
|
Certain date formats not supported in EnergyWise scheduling.
|
Symptom When you try to access the EnergyWise feature, the following
error is displayed:
An internal error has occurred.
Conditions This issue is seen when you have entered EnergyWise schedule in a format that is not supported by Cisco CP (involving commas). Cisco CP does not support manual configuration of schedules because these schedules can be read incorrectly or can cause existing schedules to be removed. Cisco CP compatible schedules contain a date format in the form of spaced numbers without the use of commas, for example energywise level 1 recurrence importance 1 at 0 1 * * 0. Wildcards (*) are allowed in addition to 0-9.
Workaround If you have a schedule with an incompatible format, convert it into multiple schedules that are compatible with Cisco CP:
energywise level 1 recurrence importance 1 at 0 1 * * 0,1,2,3,4,5,6
should be converted to:
energywise level 1 recurrence importance 1 at 0 1 * * 0
energywise level 1 recurrence importance 1 at 0 1 * * 1
energywise level 1 recurrence importance 1 at 0 1 * * 2
energywise level 1 recurrence importance 1 at 0 1 * * 3
energywise level 1 recurrence importance 1 at 0 1 * * 4
energywise level 1 recurrence importance 1 at 0 1 * * 5
energywise level 1 recurrence importance 1 at 0 1 * * 6
|
CSCto90810
|
HuntStop value is not read correctly for SIP extensions.
|
Symptom Cisco CP displays Hunt option as being enabled at all times
irrespective of the actual configuration on the device.
Conditions SIP extension is configured without HuntStop.
Workaround Manually check Hunt Settings status on the device.
|
CSCto07804
|
Traffic Monitoring Netflow Services fails to start in some scenarios.
|
Symptom Data Collector Service fails to start as a result of which data
is not collected from the router.
Conditions This can happen if files are not copied properly or get corrupted while installing the Data Collector Service.
Workaround Reinstall the Data Collector Service.
|
CSCto73606
|
Traffic Monitoring: Cisco CP displays error when you click Start Monitoring or Stop Monitoring on any interface while Data Collector Services are not running.
|
Symptom Cisco CP displays a pop-up with
Java.lang.NullPointerException error when you try to stop monitoring
by clicking on the Stop Monitoring link, while the Interface Collector
Service is not running.
Conditions Cisco CP displays error when you try to stop monitoring by clicking on the Stop Monitoring link, while the Interface Collector Service is not running.
Workaround Start the Interface Collector Service and then stop monitoring.
|
CSCto76962
|
Traffic Monitoring: Cisco CP displays value as 0 when interface is not being monitored.
|
Symptom Cisco CP displays the value as zero (0) if an interface is not
being monitored for some time.
Conditions If you monitor traffic on an interface for some time, stop and then start monitoring traffic again, Cisco CP displays a value of zero for the time interval when you were not monitoring the interface.
Workaround There is no workaround.
|
CSCtn13484
|
Device setup wizard does not remove the default ACLs on the device.
|
Symptom You cannot access device using the newly configured IP
address.
Conditions
•Case 1—When you use Setup New Device Wizard for configuring device with factory default configuration with an IP address other than 10.10.10.0 0.0.0.7 subnet.
•Case 2—When you use Setup New Device Wizard to configure an IP address that is not permitted from a configured IP access list.
Workaround
•Case 1—For factory default configuration, remove the access class defined in the default configuration using the following commands:
no ip http access-class 23
line vty 0 4
no access-class 23 in
line vty 5 15
no access-class 23 in
Or
Modify the default access list to allow the newly configured IP address:
access-list 23 permit 10.10.10.0 0.0.0.7
•Case 2—For non-default configuration, modify or remove the access class to permit the configured IP address.
|
CSCto96064
|
Rollback failing when imported phone is SIP.
|
Symptom Cisco CP displays an error message that rollback has failed on
Bulk Import and the application does not get updated. You can see bulk
imported data under phones, users, and extensions.
Conditions Rollback on Bulk Import with a SIP phone entry is failing as the commands no create profile and create profile issued during rollback fails. As a result, rollback is considered as failed although the configuration on the router created due to Bulk Import has reverted successfully.
Workaround Manually issue the command no create profile followed by the command create profile under voice register global to update the files on the Flash. Rediscover the device.
|
CSCto83180
|
Multiple virtual machines (VMs) installed on SRE-V are not displayed.
|
Symptom
•Case 1—If you did not select a virtual machine in Configure > Interface Management > Module Configuration > SRE-V > Permissions > User/Group > Edit, Select is displayed.
•Case 2—Adding one more virtual machine using Configure > Interface Management > Module Configuration > SRE-V > Permissions > User/Group > Edit removes the previously added virtual machine configuration.
•Case 3—Multiple entries are shown in the SRE-V Permissions screen for each user/group.
Conditions
•Case 1—In Configure > Interface Management > Module Configuration > SRE-V > Permissions > User/Group > Edit, when you do not select a virtual machine from the drop-down menu, Select is displayed.
•Case 2—When the user/group already has one virtual machine associated with it, adding one more virtual machine using Configure > Interface Management > Module Configuration > SRE-V > Permissions > User/Group > Edit can remove the previously added virtual machine configuration.
•Case 3—When a virtual machine, for example VM1 is already added to the user/group, adding one more virtual machine may create multiple entries in the Permissions summary screen upon refreshing the page.
Workaround
•Case 1—There is no workaround. Assume that the default virtual machine Host is associated to the user/group when Select is displayed.
•Case 2—To add multiple virtual machines to the user/group, use the CLI.
•Case 3—Read each entry as corresponding to one instance of virtual machine associated with the user/group.
|
CSCto07709
|
Mode transition from Offline to Online fails.
|
Symptom The Online to Offline mode and Offline to Online mode
transition fails with the error Persisting Device Object Failure.
Conditions This problem rarely occurs. If the Online to Offline mode transition fails, close Cisco CP and relaunch the application, it will be in the Offline mode. Transition to Online mode fails with error.
Workaround There is no workaround. Close Cisco CP and relaunch it.
|
CSCto85514
|
Internal error in phone firmware wizard screen.
|
Symptom Internal error is seen when you try to upload and configure
firmware through the phone firmware wizard.
Conditions It is not recommended to run a third party FTP server while using the phone firmware wizard in Cisco CP. In case a third party FTP server is running on the PC, an error message Upload Failed as port 21 is already in use by some other application is displayed on the Configure Phone Firmware screen. If you try uploading firmware, the internal error message is seen.
Workaround Third party FTP server should not be running when you configure phone firmware using Cisco CP.
|
CSCto93070
|
Creation of phones fails in CME as SRST mode if there are auto-registered phones on the router.
|
Symptom Phone creation using Cisco CP fails if there are
auto-registered phones.
Conditions The problem occurs when Cisco CP configures a router in CME as SRST mode with phones connected. These phones get auto-registered with the router.
Workaround Rediscover the router after configuring CME as SRST mode.
|
CSCto85895
|
GRWIC-D-ES-2S-8PC/-6S - 802.1x moving to high-security mode directly fails.
|
Symptom When you click Finish in the 802.1x wizard for
GRWIC-D-ES-2S-8PC or GRWIC-D-ES-6S with high-security or
low-impact as the mode an error Configuration failed radius-server vsa
send is seen.
Conditions This issue is seen when you click Finish in the 802.1x wizard for GRWIC-D-ES-2S-8PC or GRWIC-D-ES-6S with high-security mode or low-impact mode. The issue is not seen in the monitor mode.
Workaround Configure AAA details using monitor mode and then change to low-impact mode or high-security mode.
|
CSCth67558
|
Unable to discover switching module.
|
Symptom Cisco CP fails to discover switching module and reports that
the module is being reloaded in the discovery details.
Conditions When the switching module is configured with login local or AAA new-model configuration or both, the module requires one more level of authentication along with the usual authentication. In this case, you need to provide the username and password twice to get into the module prompt.
Workaround Remove the login local and AAA new-model configuration so that the extra level of authentication is not required.
|
CSCtj03097
|
No backup or restore with LEFS Flash type.
|
Symptom Restoring to initial configuration after merge or replace fails.
Conditions When LEFS type Flash is used, the backup and restore functionality does not work for Configuration Editor. A backup of the running configuration is not created on the Flash and so restoring to initial configuration after merge or replace fails.
Workaround Manually create a copy of the running configuration on the Flash and reload the router with that copy:
copy running-config flash
To restore the running configuration:
copy flash:RunningConfig startup-config
Reload
|
CSCto98404
|
Number of Retries Remaining displays as NULL if wrong SIM PIN is entered.
|
Symptom Cisco CP displays Numbers of Retries Remaining as NULL,
instead of the correct value.
Conditions This issue is seen when the router has IOS version 151-3.T1 or above and you enter the wrong SIM PIN to run any SIM operations on the HSPA modem.
Workaround There is no workaround.
|
CSCth34158
|
Switching Modules folder is not listed in the left navigation pane.
|
Symptom Switching Modules folder is not listed in the left navigation
pane even when the device has supported switch modules that are
managed by Cisco CP.
Conditions
•Multiple levels (more than one level) of authentication is required for accessing the switch module console.
•Enabled password is configured on the device.
•AAA is configured on both the router and the switch modules.
•Privilege level 15 is not configured under line con 0.
Workaround
•Ensure that the router and switch have the same username (privilege level 15) and a password is configured when switch console requires authentication.
•If there is no login configured for line con 0, ensure privilege level 15 is configured under line con 0.
•If AAA is configured on the router, make sure that no authentication is required for the switch module and privilege level 15 is configured under line con 0.
|
CSCtj46313
|
Sub-interfaces not listed in the Configure Cellular Wan wizard.
|
Symptom The sub-interfaces, for example interface Serial 0/0/0.1 with
encapsulation, are not listed under the Configure Cellular WAN
Wizard.
Conditions The problem is seen only with sub-interfaces. All other interface types are listed correctly in the Configure Cellular WAN Wizard.
Workaround There is no workaround.
|
CSCtk07275
|
Refresh adds more menus in the left navigation pane.
|
Symptom Invalid left navigation links display if F5 is pressed when
Cisco CP is active.Some of the new links that display are not valid for
the selected device.
Conditions Pressing the F5 button when Cisco CP is active.
Workaround There is no workaround.
|
Related Documentation
Table 12 describes the related documentation available for Cisco CP.
Table 12 Cisco Configuration Professional Documentation
Document Title
|
Available Formats
|
Readme First for
Cisco Configuration Professional
|
This document is available at the following locations:
•www.cisco.com
•Product CD-ROM in the Documentation folder
|
Cisco Configuration Professional Quick Start Guide
|
This guide is available at the following locations:
•www.cisco.com
•Product CD-ROM in the Documentation folder
|
Cisco Configuration Professional Getting Started Guide
|
This guide is available at the following locations:
•www.cisco.com
•Product CD-ROM in the Documentation folder
Note During the installation process, just before you have finished installing the product, you are provided the option to read the Getting Started guide.
|
Cisco Configuration Professional User Guide
|
This guide is available at the following locations:
•www.cisco.com
•Online help
|
Cisco Configuration Professional Express User Guide
|
This guide is available at the following locations:
•www.cisco.com
•Online help
|
Release Notes for
Cisco Configuration Professional
|
This document is available at the following location:
www.cisco.com
|
Release Notes for
Cisco Configuration Professional Express
|
This document is available at the following location:
www.cisco.com
|
Note For information on obtaining documentation and technical assistance, product security, and additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html.
Glossary
ACEs—Access List Elements
ACLs—Access Control Lists
B-ACD—Basic Automatic Call Distribution
CUBE—Cisco Unified Border Element
HWIC—High-Speed WAN Interface Card
HSPA—High-Speed Packet Access
HSPA—A—High-Speed Packet Access for Americas
HSPA—G—High-Speed Packet Access for Global
PCEX—PC Express
PPP—Point-to-Point Protocol (PPP) PDP type
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2011 Cisco Systems, Inc. All rights reserved.
Feedback
