Table Of Contents
Release Notes for
Cisco Configuration Professional 2.0
Contents
Introduction
System Requirements
PC System Requirements
Router System Requirements
Supported Routers
Supported Phones
Supported Network Modules
Supported Interface Cards
Supported Adapters, Processing Engines, and Service Engines
Cisco IOS Releases
Required IP Address Configuration Information
Router Configuration Requirements
Cisco CP Ordering Options
New and Changed Information
New Features
New Hardware Support
Limitations and Restrictions
Cisco CP Requirements to Run on Microsoft Windows Vista
Cisco CP Minimum Screen Resolution
Restrictions for Cisco 7204VXR, Cisco 7206VXR, and Cisco 7301 Routers
Cisco CP and Internet Explorer 8
Important Notes
Cisco IOS Enforces One-Time Use of Default Credentials
Cisco CP Merge and Replace Configuration Functions Fail Under Some Conditions
Cisco CP Security Dashboard May Display Threats Unrelated to Your Cisco IOS IPS Installation
Cisco CP May Lose Connection to Network Access Device
Popup Blockers Disable Cisco CP Online Help
Disable Proxy Settings
Security Alert Dialog May Remain After Cisco CP Launches
Screencasts for Cisco CP Features
Cisco Configuration Professional Is Already Running Message
Technical Support Logs Do Not Appear on Desktop
Discovery Never Completes
Caveats
Resolved Caveats from Cisco CP 1.4
Open Caveats—Cisco CP 2.0
Related Documentation
Release Notes for
Cisco Configuration Professional 2.0
October 20, 2009
These release notes support Cisco Configuration Professional (Cisco CP) version 2.0. They should be used with the documents listed in the "Related Documentation" section.
These release notes are updated as needed. To ensure that you have the latest version of these release notes, go to http://www.cisco.com/go/ciscocp. In the Support box, click General Information > Release Notes, and then find the latest release notes for your release.
Contents
This document contains the following sections:
•
Introduction
•System Requirements
•New and Changed Information
•Limitations and Restrictions
•Important Notes
•Caveats
•Related Documentation
Introduction
Cisco CP is a GUI-based device management tool for Cisco access routers. Cisco CP simplifies router, firewall, IPS, VPN, unified communications, WAN, and basic LAN configuration through GUI-based, easy-to-use wizards. Cisco CP is installed on a PC.
Routers that are ordered with Cisco CP are shipped with Cisco Configuration Professional Express (Cisco CP Express) installed in router flash memory. Cisco CP Express is a light weight version of Cisco CP, that you can use to configure LAN and WAN interfaces and minimal IOS security features.
System Requirements
This sections describes PC and router system requirements. It contains the following parts:
•PC System Requirements
•Router System Requirements
•Cisco CP Ordering Options
PC System Requirements
Table 1 lists the system requirements for a PC running Cisco CP. Although the Cisco CP application requires JRE to run, the Cisco CP Express application included with Cisco CP can run under the native Java Virtual Machine in the supported browsers, and also JRE.
Table 1 PC System Requirements
System Component
|
Requirement
|
Processor
|
2 GHz processor or faster
|
Random Access Memory
|
1 GB
|
Hard disk available memory
|
400 MB
|
Operating System
|
Any of the following:
•Microsoft Windows Vista Business Edition
•Microsoft Windows Vista Ultimate Edition
•Microsoft Windows XP with Service Pack 2 or later
•Mac OSX 10.5.6 running Windows XP using VMWare 2.0
|
Browser
|
Internet Explorer 6.0 or above
|
Screen Resolution
|
1024 X 768
|
Java Runtime Environment
|
JRE versions minimum 1.5.0_11 upto 1.6.0_16 are supported.
|
Adobe Flash Player
|
Version 10.0 or later, with Debug set to No
|
Secure Shell (SSH)
|
Required for secure connections with the router.
Versions up to 1.99 are supported.
|
Router System Requirements
Router System Requirements are described in the following parts:
•Supported Routers
•Supported Phones
•Supported Network Modules
•Supported Interface Cards
•Supported Adapters, Processing Engines, and Service Engines
•Cisco IOS Releases
•Required IP Address Configuration Information
•Router Configuration Requirements
Supported Routers
Table 2 and Table 3 list the routers that Cisco CP supports.
.
Table 2 Supported Integrated Services Routers (ISR)
Cisco 800 Series
|
Cisco 1800 Series
|
Cisco 2800 Series
|
Cisco 3800 Series
|
Cisco 7000 Series
|
CISCO815
CISCO815-VPN-K9
|
CISCO1801
CISCO1801-M
CISCO1801/K9
CISCO1801-M/K9
CISCO1801WM-AGE/K9
CISCO1801W-AG-E/K9
CISCO1801W-AG-B/K9
CISCO1801W-AG-C/K9
CISCO1801W-AG-N/K9
|
Cisco 2801
Cisco 2811
Cisco 2821
Cisco 2851
|
Cisco 3825
Cisco 3825-NOVPN
Cisco 3845
Cisco 3845-NOVPN
|
Cisco 7204VXR
Cisco 7206VXR
Cisco 7301
|
|
|
|
|
|
|
|
CISCO851-K9
CISCO851W-G-A-K9
CISCO851W-G-E-K9
CISCO851W-G-J-K9
|
CISCO1802
CISCO1802/K9
CISCO1802W-AG-E/K9
|
CISCO857-K9
CISCO857W-G-A-K9
CISCO857W-G-E-K9
|
CISCO1803/K9
CISCO1803W-AG-B/K9
CISCO1803W-AG-E/K9
|
CISCO871-K9
CISCO871-SEC-K9
CISCO871W-G-A-K9
CISCO871W-G-E-K9
CISCO871W-G-J-K9
|
CISCO1805-D
CISCO 1805-D/K9
|
|
|
|
|
CISCO1811/K9
CISCO1811W-AG-B/K9
CISCO1811W-AG-C/K9
CISCO1811W-AG-N/K9
|
CISCO876-K9
CISCO876-SEC-K9
CISCO876-SEC-I-K9
CISCO876W-G-E-K9
|
CISCO1812/K9
CISCO1812 W-AG-E/K9
CISCO1812 W-AG-C/K9
|
CISCO877-K9
CISCO877-M-K9
CISCO877-SEC-K9
CISCO877W-G-A-K9
CISCO877W-G-E-K9
CISCO877W-G-E-M-K9
|
CISCO1841
|
CISCO878-K9
CISCO878-SEC-K9
CISCO878W-G-A-K9
CISCO878W-G-E-K9
|
C1861-UC-4FXO-K9
C1861-UC-2BRI-K9
C1861-SRST-B/K9
C1861-SRST-C-B/K9
C1861-SRST-C-F/K9
C1861-SRST-F/K9
|
Table 3 Supported Integrated Services Routers - G2 (ISR- G2)
Cisco 800 Series
|
Cisco 1900 Series
|
Cisco 2900 Series
|
Cisco 3900 Series
|
CISCO861-K9
CISCO861W-GN-A-K9
CISCO861W-GN-E-K9
CISCO861W-GN-P-K9
|
CISCO1941/K9
CISCO1941W-A/K9
CISCO1941W-E/K9
CISCO1941W-P/K9
CISCO1941W-N/K9
|
CISCO2901/K9
CISCO2911/K9
CISCO2921/K9
CISCO2951/K9
|
CISCO3925/K9
CISCO3945/K9
|
CISCO867-W-GN-A-K9
CISCO867-W-GN-E-K9
|
CISCO881-K9
CISCO881W-GN-A-K9
CISCO881W-GN-E-K9
CISCO881W-GN-P-K9
CISCO881G-K9
CISCO881GW-GN-A-K9
CISCO881GW-GN-E-K9
CISCO881G-S-K9
CISCO881G-V-K9
CISCO881G-A-K9
CISCO881SRST-K9
CISCO881SRSTW-GN-A-K9
CISCO881SRSTW-GN-E-K9
|
CISCO886-K9
CISCO886W-GN-E-K9
CISCO886G-K9
CISCO886GW-GN-E-K9
|
CISCO887-K9
CISCO887W-GN-A-K9
CISCO887W-GN-E-K9
CISCO887M-K9
CISCO887MW-GN-E-K9
CISCO887G-K9
CISCO887GW-GN-A-K9
CISCO887GW-GN-E-K9
|
CISCO888-K9
CISCO888W-GN-A-K9
CISCO888W-GN-E-K9
CISCO888G-K9
CISCO888GW-G-AN-K9
CISCO888GW-G-EN-K9
|
|
|
|
CISCO888SRST-K9
CISCO888SRSTW-GN-A-K9
CISCO888SRSTW-GN-E-K9
|
CISCO891-K9
CISCO891W-AGN-A-K9
CISCO891W-AGN-N-K9
|
CISCO892-K9
CISCO892W-AGN-E-K9
|
Supported Phones
Table 4 lists the phones that Cisco CP supports:
Table 4 Supported Phones
Supported Phones
|
Supported Expansion Modules
|
Supported Conference Stations
|
7902G
7905
7906G
7910G
7911G
7912G
7920
7921G
7931G
7940G
7941G
7941G-GE
7942G
7945G
7960G - expansion module compatible (7914)
7961G - expansion module compatible (7914)
7961G-GE
7962G - expansion module compatible (7915,7916)
7965G - expansion module compatible (7915,7916)
7970G - expansion module compatible (7914)
7971G - expansion module compatible (7914)
7975G - expansion module compatible (7915,7916)
7985G
ATA
CIPC - Cisco IP Communicator
|
7914
7915-12
7915-24
7916-12
7916-24
|
7935
7936
7937G
|
Supported Network Modules
Table 5 and Table 6 list the network modules that Cisco CP supports.
Table 5 Supported Network Modules
Network Modules
|
Enhanced Network Modules
|
Wide Area Application Services (WAAS) Modules
|
Advanced Integration Modules (AIMs)
|
Voice Network Modules
|
NM-4T
NM-1FE2W-V2
NM-1FE-FX-V2
NM-2FE2W-V2
NM-1FE-FX
NM-4A/S (synchronous only)
NM-8A/S (synchronous only)
NM-CIDS-K9
NM-16ESW
NM-16ESW-1GIG
NM-16ESW-PWR
NM-16ESW-PWR-1GIG
NMD-36ESW-PWR
NMD-36ESW-PWR-2GIG
|
NME-IPS-K9
NME-16ES-1G-P
NME-X-23ES-1G-P
NME-XD-24ES-1S-P
NME-XD-48ES-2S-P
NME-VMSS-16
NME-VMSS-HP-16
NME-VMSS-HP-32
|
NME-WAE-502-K9
NME-WAE-522-K9
NME-WAE-302-K9
|
AIM-VPN/BP II PLUS
AIM-VPN/EP II PLUS
AIM-VPN/HP II PLUS
AIM-VPN/SSL-1
AIM-VPN/SSL-2
AIM-VPN/SSL-3
AIM-IPS-K9
AIM-CUE
AIM2-CUE-K9
|
NM-HD-1V
NM-HD-2V
NM-HD-2VE
NM-HDA-4FXS
NM-HDV2
NM-HDV2-1T1/E1
NM-HDV2-2T1/E1
EVM-HD-8FXS/DID
EM-HDA-8FXS
EM-HDA-4FXO
EM2-HDA-4FXO
EM-HDA-3FXS/4FXO
EM-HDA-6FXO
EM-4BRI-NT/TE
NM-CUE
NM-CUE-EC
NME-CUE
EM3-HDA-8FXS/DID
|
Table 6 Supported Cisco SRE Internal Service Modules and EtherSwitch Modules
Cisco SRE Internal Service Modules
|
EtherSwitch Modules
|
ISM-SRE-300-K9
|
SM-ES2-16-P
SM-ES2-24
SM-ES2-24-P
SM-D-ES2-48
SM-ES3-16-P
SM-ES3G-16-P
SM-ES3-24-P
SM-ES3G-24-P
SM-D-ES3-48-P
SM-D-ES3G-48-P
|
Supported Interface Cards
Table 7, lists the interface cards that Cisco CP supports.
Table 7 Supported Cards
WAN Interface Cards (WICs)
|
High-speed WAN Interface Cards (HWICs)
|
Voice Interface Cards
|
WIC-1T
WIC-2T
WIC-2A/S (Frame Relay, PPP, HDLC, no asynchronous)
WIC-1ADSL
WIC-1DSU-T1-V2
WIC-1B-S/T-V3
WIC-1AM
WIC-2AM
WIC-4ESW
WIC-1SHDSL-V2
WIC-1SHDSL-V3
WIC 1ADSL-DG
WIC 1ADSL-I-DG
|
HWIC-1T
HWIC-2T
HWIC-4T
HWIC-2A/S
HWIC-4A/S
HWIC-4ESW
HWIC-4ESW-POE
HWIC-8A
HWIC-8A/S-232
HWIC-D-9ESW
HWIC-D-9ESW-POE
HWIC-1DSU-T1
HWIC-16A
HWIC-ADSL-B/ST
HWIC-ADSLI-B/ST
HWIC-1ADSL
HWIC-1ADSLI
HWIC-1ADSL-M (WIC card with Annex M)
HWIC-2SHDSL
HWIC-4SHDSL
HWIC1-ADSL-M
HWIC-1CABLE-D-2
HWIC-1CABLE-E/J-2
HWIC-1FE
HWIC-2FE
HWIC-AP-AG-A
HWIC-AP-AG-E
HWIC-AP-AG-J
HWIC-AP-G-A
HWIC-AP-G-E
HWIC-AP-G-J
HWIC-3G-GSM
HWIC-3G-CDMA-S
HWIC-3G-CDMA-V
|
VIC2-4FXO
VIC2-2FXS
VIC2-2FXO
VIC2-2BRI-NT/TE
VIC-2DID
VIC-4FXS/DID
VIC3-4FXS/DID
VIC3-2FXS/DID
VWIC2-1MFT-T1/E
VWIC2-2MFT-T1/E1
|
|
|
|
|
|
|
|
Supported Adapters, Processing Engines, and Service Engines
Table 8 lists the adapters, processing engines, and service engines that Cisco CP supports.
Table 8 Supported Adapters, Processing Engines, and Service Engines
Port Adapters on Cisco 7000 Series Routers
|
Service Adapters on Cisco 7000 Series Routers
|
Network Processing Engines and Network Service Engines on Cisco 7000 Series Routers
|
PA-2FE-TX
PA-2FE-FX
PA-8E
PA-4E
|
SA-VAM
SA-VAM2
SA-VAM2+
C7200-VSA
|
NPE-225
NPE-400
NPE-G1
NPE-G2
NSE-1
|
|
|
|
|
|
|
|
Cisco IOS Releases
Cisco CP is compatible with the Cisco IOS releases listed in Table 9.
Table 9 Cisco CP-Supported Routers and Cisco IOS Versions
Router Model
|
Earliest Cisco CP-Supported Cisco IOS Versions
|
Cisco 815
|
•12.4(11)T
|
Cisco 850 series
|
•12.4(9)T
|
Cisco 861
|
•12.4(20)T
|
Cisco 867
|
•15.0(1)M
|
Cisco 870 series
|
•12.4(9)T
|
Cisco 881
|
•12.4(20)T
|
Cisco 886
|
•15.0(1)M
|
Cisco 887
|
•15.0(1)M
|
Cisco 888
|
•12.4(20)T
|
Cisco 890 series
|
•15.0(1)M
|
Cisco 1801
Cisco 1802
Cisco 1803
|
•12.4(9)T
|
Cisco 1805
|
•12.4(15)XY
|
Cisco 1811
Cisco 1812
|
•12.4(9)T
|
Cisco 1841
|
•12.4(9)T
|
Cisco 1861
|
•12.4(20)T
|
Cisco 1941
Cisco 1941W
|
•15.0(1)M
|
Cisco 2800 series
|
•12.4(9)T
|
Cisco 2900 series
|
•15.0(1)M
|
Cisco 3800 series
|
•12.4(9)T
|
Cisco 3900 series
|
•15.0(1)M
|
Cisco 7000
|
•12.4(9)T
|
Determining the Cisco IOS Release
To determine the release of Cisco IOS software currently running on your Cisco router, log in to the router and enter the show version EXEC command. The following sample output from the show version command indicates the Cisco IOS release on the second output line:
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (c1700-k8sv3y7-mz) Version 12.2(13)ZH
Required IP Address Configuration Information
Table 10 provides the required IP address configuration for the PC. Use this information to complete the section "Task 4: Configure the IP Address On the PC" in the Cisco Configuration Professional Quick Start Guide.
Table 10 Required PC IP Address Configurations
Router Model
|
DHCP Server
|
Required PC IP Address Configuration
|
Cisco 815, Cisco 85x, Cisco 86x, Cisco 87x, Cisco 88x, Cisco 89x, Cisco 180x, Cisco 1805, Cisco 1811 and 1812
|
Yes
|
Obtain an IP address automatically.
|
Cisco 1841, Cisco 1861, Cisco 28xx, Cisco 38xx
|
No
|
Static IP address from 10.10.10.2 to 10.10.10.6
Subnet Mask: 255.255.255.248
|
Router Configuration Requirements
In order to run Cisco CP, a router configuration must meet the requirements shown in Table 11.
Table 11 Router Configuration Requirements
Feature
|
Requirement
|
Configuration Example
|
Secure access
|
SSH and HTTPS
|
Router(config)# ip http secure-server
Router(config)# line vty 0 4
Router(config-line)# transport input ssh
|
Nonsecure access
|
Telnet and HTTP
|
Router(config)# ip http server
Router(config)# line vty 0 4
Router(config-line)# transport input telnet
|
User privilege level
|
15
|
Router(config)# username cisco privilege 15 secret 0 cisco
|
The default configuration file meets all Cisco CP requirements. The default configuration file has the name cpconfig-model_number.cfg. For example, the configuration file for the Cisco 860 and Cisco 880 routers is cpconfig-8xx.cfg.
Cisco CP Ordering Options
Table 12 describes the ordering options under which Cisco CP can be ordered. Cisco Configuration Professional Express (Cisco CP Express) is a product that is shipped in router flash memory when the router is ordered with Cisco CP.
Table 12 Cisco CP Ordering Options
Ordering Options
|
Description
|
CCP-CD
|
Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in NVRAM
|
CCP-CD-NOCF
|
Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory
Note This ordering option does not provide the default configuration file for Cisco 800 series routers.
|
CCP-EXPRESS
|
Cisco CP: Not shipped
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in NVRAM
|
CCP-EXPRESS-NOCF
|
Cisco CP: Not shipped
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory
Note This ordering option does not provide the default configuration file for Cisco 800 series routers.
|
ISR-CCP-CD=
|
Cisco CP: Shipped on CD
Spare SKU: Mapped to ISR-CCP-CD
|
ISR-CCP-CD
|
Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in NVRAM
|
ISR-CCP-CD-NOCONF
|
Cisco CP: Shipped on CD
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory
|
ISR-CCP-EXP
|
Cisco CP: Not shipped
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory and in NVRAM
|
ISR-CCP-EXP-NOCONF
|
Cisco CP: Not shipped
Cisco CP Express: Shipped in router flash memory
SSL Client: Shipped in router flash memory
Default Configuration File: Shipped in router flash memory
|
New and Changed Information
This section contains new information about Cisco CP, and any information about Cisco CP that has changed.
This section contains the following parts:
•New Features
•New Hardware Support
New Features
Cisco CP 2.0 supports the following new features:
•Import and Export Community— The Import and Export Communities feature allows you to save (export) the information about all the communities in Cisco CP to a file on your PC, and then import that information from your PC into Cisco CP.
•License Management—The Cisco License Management feature allows you to register and manage feature licenses by securely communicating with the Cisco Product License Registration portal (Cisco licensing portal) to obtain the license, and then allows you to install and deploy the license on a selected device.
•User Profile—Earlier you were allowed to access only certain domains or screens. For example, the security administrator was allowed access only to the security screens and the network administrator had access only to the routing screens. With the User Profile feature, you can choose a view for each router. The views are Routing, Security, Voice, Default and so on. You can select read or read-write for each feature displayed in the view.
•Template Support—Using this feature, you can generate a template from the running configuration of a device, modify parameters as needed, and apply to the same or another device.
•Cellular WAN—This feature supports Third Generation (3G) Wireless High-Speed WAN interface Card (HWIC). The HWIC will function as any other WAN interface on Cisco 1841, 28xx, and 38xx routing platforms. For 881G, 886G, 887G, and 888G, this feature is available in a PCMCIA form. Cisco CP 2.0 provides the following features to support 3G HWIC:
–Creating a cellular interface for CDMA (Sprint), CDMA (Verizon) and GSM HWICs
–Editing the existing cellular interface
–Deleting the cellular interface configurations
–Monitoring the cellular interfaces
•Module Configuration—The new Internal Service Modules (ISM) allows installation and uninstallation of Cisco Unity Express and AXP applications. Cisco CP 2.0 displays the modules available and also the currently installed application. Cisco CP 2.0 also provides funtionalities to change the application or install a new application on the module.
•Module Power Management—This feature allows you to turn power on and off for the new ISM modules.
•Flash File Management—ISR-G2 routers have two flashes. In that case, you need to select the flash you want to save in.
•Dial Plan—All dial plan related features are enhanced so that apart from basic common use cases, you can also change some of the advanced configuration options for dial plans. These include Incoming Dial Plan, Outgoing Dial Plan, Intersite VoIP, Gateway VoIP, and SRST Rerouting.
•Trunk Group—Cisco CP 2.0 allows creation of trunk group by associating multiple trunks to create the group. Cisco CP also provide the functionality to create dial-peer and associate it to trunk group. This reduces the number of CLIs generated for dial-plan feature when dial-plan has to be applied to multiple trunks.
•Advanced Global Parameters—The Advanced Global Parameters feature allows you to enable or disable VoIP parameters and to manage Voice Class Codec entries.
–Voice Class Codec—The Voice Class Codec feature enables a Cisco device to connect to other VoIP devices without having prior knowledge about the codec that is used in a call-setup.
–VoIP Parameters—The VoIP Parameters feature allows you to enable or disable connections between specific types of end points; and to enable or disable supplementary services. Supplementary services are used for call transferring, call forwarding, and message waiting indication (MWI) capabilities across a VoIP network.
•CME as SRST—Cisco Unified CME 4.0 provides fallback functionality to IP phones that are registered to Call Manager. When connectivity to the Call Manager is lost or when the server goes down, the phones re-home and register with CME which is configured to provide SRST services. This solution provides access to all the features that CME normally provides while the phones are in fallback mode without any additional licensing cost.
•Extension Templates - The Extension Templates feature allows you to apply a standard set of features such as Pickup Group Number, Call Forward Busy Number, and Call Forward No Answer Number to extensions.
New Hardware Support
The new devices supported are:
•CISCO1941/K9
•CISCO1941W-A/K9
•CISCO1941W-E/K9
•CISCO1941W-P/K9
•CISCO1941W-N/K9
•CISCO2901/K9
•CISCO2911/K9
•CISCO2921/K9
•CISCO2951/K9
•CISCO3925/K9
•CISCO3945/K9
The new network modules supported are:
•SM-ES2-16-P
•SM-ES2-24
•SM-ES2-24-P
•SM-D-ES2-48
•SM-ES3-16-P
•SM-ES3G-16-P
•SM-ES3-24-P
•SM-ES3G-24-P
•SM-D-ES3-48
•SM-D-ES3G-48-P
•ISM-SRE-300-K9
•AIM2-CUE-K9
•EM3-HDA-8FXS/DID
Limitations and Restrictions
This section describes restrictions and limitations that may apply to Cisco CP. It contains the following parts:
•Cisco CP Requirements to Run on Microsoft Windows Vista
•Cisco CP Minimum Screen Resolution
•Restrictions for Cisco 7204VXR, Cisco 7206VXR, and Cisco 7301 Routers
•Cisco CP and Internet Explorer 8
Cisco CP Requirements to Run on Microsoft Windows Vista
In order to run Cisco CP under Microsoft Windows Vista, Cisco CP must be installed in Administrator mode. You can do this by following the Microsoft Windows instructions to create an administrative account, and then logging on to the PC using that account name and password before installing Cisco CP. Failure to do this will require you to right-click on the Cisco CP icon or menu item, and choose "Run as administrator" each time you want to run Cisco CP.
Cisco CP Minimum Screen Resolution
Cisco CP requires a screen resolution of at least 1024 x 768.
Restrictions for Cisco 7204VXR, Cisco 7206VXR, and Cisco 7301 Routers
The following restrictions apply to Cisco CP running on Cisco 7204VXR, Cisco 7206VXR, and Cisco 7301 Routers:
•The Cisco CP Express application is not supported. You must use the Cisco IOS CLI to give the router an initial configuration that will enable you to connect to the router using a browser.
•WAN configuration is not supported. Cisco CP supports configuration of Ethernet and Fast Ethernet interfaces.
•The Cisco CP Reset feature is not available.
•No default configuration file is supplied. To run Cisco CP, you must provide a configuration that includes the commands necessary to support operation of Cisco CP.
Cisco CP and Internet Explorer 8
In some systems (Windows XP and Windows Vista), with IE8 installed, Cisco CP may not work as expected. This is due to a reported IE 8 caching issue.
IE8 reinstall or clearing the cache does not help. Any Flash based application like Cisco CP will see this issue.
A workaround today is to create another user account with appropriate privileges and run Cisco CP in that user account.
A fix will be made available in Cisco CP 2.1.
Important Notes
This section contains important information for Cisco CP. It contains the following sections:
•Cisco IOS Enforces One-Time Use of Default Credentials
•Cisco CP Merge and Replace Configuration Functions Fail Under Some Conditions
•Cisco CP Security Dashboard May Display Threats Unrelated to Your Cisco IOS IPS Installation
•Cisco CP May Lose Connection to Network Access Device
•Popup Blockers Disable Cisco CP Online Help
•Disable Proxy Settings
•Security Alert Dialog May Remain After Cisco CP Launches
•Screencasts for Cisco CP Features
Cisco IOS Enforces One-Time Use of Default Credentials
To address CSCsm25466, Cisco IOS images included with recent shipments of Cisco 800, Cisco 1800, Cisco 2800, and Cisco 3800 routers, enforce the one-time use of the default user name and password provided in the Cisco CP configuration file. If you bypass Cisco CP or Cisco CP Express and use a console or Telnet connection to log into the router, the login and exec banners warn you that you must change the user name "cisco" and password "cisco" before you log off of the router. If you do not change the credentials as directed, you will not be able to log on to the router the next time that you attempt to do so.
The following Cisco IOS releases enforce the one-time use of the default credentials:
•12.4(11)T or later
•12.4(11)SW, 12.4(11)SW1, 12.4(11)XV, 12.4(11)XJ
•12.4(9)T5, 12.4(9)T6
•12.3(21), 12.3(22)
Follow the procedure in this section to secure the router by creating a new username and password, to remove the login banner and exec banner warnings, and to save the configuration changes to the router startup configuration.
Note If you login to the router using a Telnet or a console connection but do not complete the steps in this procedure, be aware of the following:
•If you do not change the default username and password, and then log off the router, you will not be able to log into the router again without entering the reload command. No additional warning is given before you log off.
•If you do not change the default username and password, but do enter the write memory command before ending the session, future logins will be disabled. In this case, you will need to follow the password recovery procedure at the following link:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1831/products_tech_note09186a00801746e6.shtml
To secure the router, remove the banner warnings and save the changes to the router startup config, complete the following steps:
Step 1 Connect the light blue console cable, included with your router, from the blue console port on your router to a serial port on your PC. Refer to your router's hardware installation guide for instructions.
Step 2 Connect the power supply to your router, plug the power supply into a power outlet, and turn on your router. Refer to your router's quick start guide for instructions.
Step 3 Use HyperTerminal or a similar terminal emulation program on your PC, with the terminal emulation settings of 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control, to connect to your router.
Step 4 When prompted, enter the username cisco, and password cisco.
Step 5 Enter configuration mode by entering the following command:
yourname# configure terminal
Step 6 Create a new username and password by entering the following command:
yourname(config)# username username privilege 15 secret 0 password
Replace username and password with the username and password that you want to use.
Step 7 Remove the default username and password by entering the following command:
yourname(config)# no username cisco
Step 8 To remove the login banner, enter the following command:
yourname(config)# no banner login
The login banner warning will no longer appear.
Step 9 To remove the exec banner, enter the following command:
yourname(config)# no banner exec
The exec banner warning will no longer appear.
Step 10 Leave configuration mode, by entering the following command:
Step 11 Copy the configuration changes to the startup configuration by entering the following command:
yourname# copy running-config startup-config
When logging into the router in the future, use the username and password that you created in Step 6.
Cisco CP Merge and Replace Configuration Functions Fail Under Some Conditions
The problem described here is caveat CSCsj21989. If you attempt to merge configuration changes made using the Cisco CP Config Editor feature, or replace the running configuration with a configuration from the Config Editor, the router configuration will not be changed if there is a network device with a Network Address Translation (NAT) IP address, or a cache engine in the connection between the PC and the router. If you need to make changes to the router configuration that you would normally make using the Cisco CP Config Editor, use the Cisco IOS CLI instead.
Cisco CP Security Dashboard May Display Threats Unrelated to Your Cisco IOS IPS Installation
Some (or all) of the top threats you obtain using the Cisco CP Security Dashboard may not pertain to your Cisco IOS IPS installation. After you deploy the signatures applicable to the top threats displayed by the Cisco CP Security Dashboard, the dashboard may still display some (or all) top threats with a red icon because applicable signatures could not be found. Those remaining top threats are unrelated to your Cisco IOS IPS installation and not a danger to your router running Cisco IOS software.
Cisco CP May Lose Connection to Network Access Device
This note concerns the Network Admission Control (NAC) feature.
If the PC used to invoke Cisco CP returns a posture state (Healthy, Infected, Checkup, Quarantine, or Unknown) and if the group policy on the ACS server attached to the posture token assigned to the PC has a redirect URL configured, the connection between Cisco CP and the router acting as the Network Access Device (NAD) may be lost. The same problem can occur if an exception list entry attached to a policy with a redirect URL is configured with the IP address or MAC address of the PC.
If you try to reinvoke Cisco CP from this PC, you will not be able to do so because the browser will be redirected to the location specified in the redirect URL.
There are two workarounds for this problem:
•Ensure that the PC that you use to invoke Cisco CP attains a posture token which has an associated group policy on the ACS server that is not configured with a redirect URL.
•Alternatively, use Cisco CP to create a NAC exception list entry with the IP address or MAC address of the PC you use to invoke Cisco CP. Note that the exception list entry created for the PC should be associated to an exception policy which does not have a redirect URL configured in it.
For more information, see the links in the Cisco CP NAC online help pages.
Popup Blockers Disable Cisco CP Online Help
If you have enabled popup blockers in the browser you use to run Cisco CP, online help will not appear when you click the help button. To prevent this from happening, you must disable the popup blocker when you run Cisco CP. Popup blockers may be enabled in search engine toolbars, or may be standalone applications integrated with the web browser.
Microsoft Windows XP with Service Pack 2 blocks popups by default. In order to turn off popup blocking in Internet Explorer, go to Tools > Pop-up Blocker > Turn Off Pop-up Blocker.
If you have not installed and enabled third-party pop up blockers, go to Tools >Internet Options > Privacy, and uncheck the Block popups checkbox.
Disable Proxy Settings
Cisco CP will not start when run under Internet Explorer with proxy settings enabled. To correct this problem, choose Internet Options from the Tools menu, click the Connections tab, and then click the LAN settings button. In the LAN Settings window, disable the proxy settings.
Security Alert Dialog May Remain After Cisco CP Launches
When Cisco CP is launched using HTTPS, a security alert dialog box that informs you of possible security problems and asks you if you want to proceed with program launch may appear. This can happen if the router does not have the following global configuration command in the running configuration:
ip http timeout-policy idle 600 life 86400 requests 10000
Screencasts for Cisco CP Features
Instead of online help, we have provided screencasts for the following Cisco CP 2.0 features:
•User Profiles
•Templates
•Cellular WAN
•CME as SRST
•Dial Plan (updated to include Trunk Groups)
•Module Configuration
•Module Power Management
•Extension Templates
•License Management (For this feature, we have provided online help as well as a screencast.)
These screencasts are located at: http://www.cisco.com/en/US/docs/net_mgmt/cisco_configuration_professional/scrcst/ccpsc.html
You must have internet access to view the screencasts.
Cisco Configuration Professional Is Already Running Message
If Cisco CP has not been shut down properly, and you try to relaunch it, you may see the following message: "Cisco Configuration Professional is already running. Only one occurrence can run at a time." To correct this problem and relaunch Cisco CP, do the following:
Step 1 Press Ctrl Alt Delete, and click Task Manager.
Step 2 In the Windows Task Manager dialog, click Processes.
Step 3 In the Image Name column, highlight the processes CiscoCP.exe, CiscoCPEngine.exe, IEC2.exe, and SplashScreen.exe.
Step 4 Click End Process.
Step 5 Wait 30 seconds, and then restart Cisco CP.
Technical Support Logs Do Not Appear on Desktop
If the technical support logs folder does not appear on the desktop, there may be installed Java applications preventing this feature from working properly. To check, go to Start > Control Panel > Add or Remove Programs, and scan the list for Java applications. Remove the Java applications that you can, and try again.
Discovery Never Completes
Because of Microsoft Windows Java caching issues, Cisco CP is sometimes unable to complete discovery of a device. To fix this issue, complete the following steps:
Step 1 Choose Application > Exit to shut down Cisco CP.
Step 2 Go to Start > Control Panel > Java. The General tab is displayed.
Step 3 In the Temporary Internet Files box, click Delete Files.
Step 4 In the displayed dialog, leave all file types checked, and click OK.
Step 5 Click OK in the Java control panel to close it.
Step 6 Restart Cisco CP.
Caveats
Caveats describe unexpected behavior in Cisco CP. This section contains the following:
•Resolved Caveats from Cisco CP 1.4
•Open Caveats—Cisco CP 2.0
Resolved Caveats from Cisco CP 1.4
Table 13 lists caveats that are resolved in Cisco CP 2.0.
Table 13 Resolved Caveats in Cisco CP 2.0
Bug ID
|
Summary
|
CSCsy50471
|
Enable option should not be shown when the VDSL interface is up.
|
CSCsl65044
|
Array values displayed when the mouse is placed over list in the user screen.
|
CSCsq52996
|
Need to support SIP for self zone in Cisco CP.
|
CSCsy06399
|
Error #2032 is seen on the Router Status dialog box.
|
CSCtb14050
|
Cisco CP hangs when trying to upload files through SSL VPN.
|
CSCta95900
|
CSCta95900 - Outgoing dial plan configures invalid destination pattern.
|
CSCtb07893
|
Acknowledge error on importing Outgoing dial plan in the offline mode.
|
CSCta12755
|
Configuration failed when trying to deliver CLIs to the router.
|
CSCta65551
|
DID trunk configuration is failing in Online mode.
|
CSCta86408
|
Device needs to be discovered after moving to the online mode.
|
CSCta93218
|
Disabling CLI view in online mode causes CLIs to be sent directly.
|
CSCta95721
|
EM-4BRI-NT/TE ports under EVM-HD-8FXS/DID not getting discovered.
|
CSCtb03710
|
PRI Settings voice port values are not displayed correctly.
|
CSCtb05571
|
Forward PSTN access digit does not work.
|
CSCtb10599
|
Switching between devices in the offline mode shows incorrect data.
|
CSCtb14313
|
Cisco CP allows class removal with Firewall PT in GETVPN.
|
CSCtb24637
|
Post install fails for Pano device.
|
CSCtb25590
|
Deleting multiple extensions throws exception.
|
Open Caveats—Cisco CP 2.0
Table 14 lists caveats that are open in Cisco CP 2.0.
Table 14 Open Caveats in Cisco CP 2.0
Bug ID
|
Summary
|
Additional Information
|
CSCsm91019
|
Security screens overlap over menu bar options and tool bar information.
|
Symptom: Some of the menu bar options, either Tools or Help. are hidden under security screens.
Conditions: You are in Routing or Security features screen while selecting the menu options.
Workaround: Move to any other feature other than Routing or Security, the issue will not be seen.
|
CSCsm95507
|
Cisco CP icon is changed to Internet Explorer icon after a while in the titlebar.
|
Symptom: The icon of Cisco CP application window changes to Internet Explorer icon.
Conditions: After the successful launch of Cisco CP, minimize the Cisco CP screen and keep it minimized for a while.
Workaround: There is no workaround.
|
CSCsw23556
|
Security Applet is not responding error during discovery.
|
Symptom: Discovery of a device failed with the error Security Applet not responding.
Conditions: This issue happens intermittently.
Workaround: Re-launch the application.
|
CSCsw31280
|
CLI Preview dialog box moves to the background.
|
Symptom: When configuring security features, you click the Add, Edit, or other command buttons in the user interface, the dialog boxes do not open.
Conditions: CLI Preview dialog box is not closed and is present in the background.
Workaround: Resize or move the main Cisco CP window and complete the CLI preview dialog options that are hidden in the background to continue.
|
CSCsw39659
|
Enhancement in Cisco CP for CUE post initialization.
|
Symptom: The data fields for CUE post initialization wizard are not retained on Cisco CP if you use the back button. It is time consuming to enter all the values again.
Conditions: This issue occurs only when any field value is invalid in the CUE post initialization wizard.
Workaround: To avoid this situation, make sure that you enter the correct values so that you do not have to use the back button.
|
CSCsx05868
|
Unable to upload CME phone load tar file.
|
Symptom: In Cisco Configuration Professional, while trying to upload phone load tar file from the Voice > Phone Firmware feature, phone load upload might fail after some upload progress.
Conditions: On device if exec-timeout</CmdBold> is not set under line vty</CmdBold> configurations or if exec-timeout</CmdBold> is set with a smaller timeout value, then phone load upload might fail.
Workaround: On device, under all line vty</CmdBold> configs, set exec-timeout</CmdBold> config with proper timeout value. Example: vty line 0 4 exec-timeout 25 0 exit
Further Problem Description: exec-timeout is used to set the interval that the EXEC command interpreter waits until user input is detected. If no input is detected during this interval, the EXEC facility returns the terminal to the idle state and disconnects the incoming session. A big size phone load tar file might take some time to get uploaded on the device's flash. So to avoid any error during upload, exec-timeout should be set with a value greater than the time taken by upload of big tar file. If exec-timeout is set as 0 0, then vty lines may get blocked if session is not exited/closed properly.
|
CSCsx57080
|
Cisco CP launching issue with Internet Explorer 8.
|
Symptom: Unable to launch Cisco CP.
Conditions: Using Internet Explorer 8 release candidate 1.
Workaround: Downgrade to Internet Explorer 7.
|
CSCsx72139
|
Cisco CP discover details should give warning in case of insufficient memory.
|
Symptom: Voice menu folder is disabled in the Cisco CP GUI.
Conditions: The router running IOS version 12.4(24)T or later has insufficient memory to enable telephony-service.
Workaround: Upgrade the DRAM in the router.
|
CSCsx75097
|
Unity express module discovery fails with SSH version >=2.0.
|
Symptom: Cisco Unity Express module discovery fails with an error message stating that the device is configured with unsupported SSH version. The error messages are shown in the discovery details user interface. Due to this error message, none of the CUE features are available.
Conditions: The device is configured with SSH version higher than or equal to 2.0.
Workaround: Reconfigure the SSH version to lesser than 2.0, or use Telnet to communicate with the device.
|
CSCsy49785
|
Service group not working for QoS, SSLVPN, NAC, and access-class.
|
Symptom: OGACL with service group not working for QoS, SSLVPN, NAC, and access-class.
Conditions: When associating an OGACL with service object group to QoS, SSL VPN, NAC, and access-class, the traffic does not match. This is due to an IOS issue.
Workaround: There is no specific workaround. Use normal ACLs with these features. Once the IOS bug is fixed, this will be fixed in Cisco CP.
|
CSCsy87964
|
CPU utilization at 100% when discovering devices.
|
Symptom: After discovery of 5 devices in a community, some with secure mode, CPU shoots to 100% utilization and does not drop. CiscoCPEngine.exe CPU usage is in the range 83%-95%.
Conditions: This problem occurs if one of the devices in the community, has high security configuration and bandwidth filters for the WAN interface. This problem does not occur in other PC environments.
Workaround: There is no workaround.
|
CSCsz13428
|
Configuration error on creating or editing outgoing dial-plan.
|
Symptom: Dial-plan related configuration fails saying dial-peer tag is already in use. This issue occurs occasionally when voice hunt-group is configured on the router.
Conditions: When hunt-group is configured with pilot CLI, and the pilot number is too huge to be the dial-peer tag.
Further Problem Description: When hunt-group is configured with pilot CLI, the router creates a dial-peer with the pilot number as the dial-peer tag. This dial-peer is not displayed in show run, and Cisco CP does not read these dial-peers (only show run is used to read in dial-peer configurations). However, these dial-peers can be seen in show dial-peer voice summary.
In normal circumstances, the pilot number and the dial-peer tag are large numbers. This is not an issue for Cisco CP as Cisco CP always chooses the smallest tag number available to configure dial-peers and there is never any overlap of tags. However, if the pilot number is too large to be a tag for dial-peer, the router chooses the next available smallest tag number to configure the dial-peer for that hunt group. In such a situation, Cisco CP configuration for dial-plan might cause a problem because the tag that Cisco CP chooses, can overlap with the already configured hunt group related dial-peer, which results in configuration failure.
|
CSCsz13759
|
Deleting of extensions fails if configured as Monitor/Shared.
|
Symptom: Error while deleting multiple extensions together.
Conditions: Create 6 extensions. For example, 1000, 2000, 3000, 4000, 5000, 6000.
Assign extensions 1000, 2000, 3000 on button 1 of user1; and extensions 4000, 5000, 6000 on button 2 of user1. Assign extension 1000, 2000, 3000, 4000, 5000, 6000 on button1 of user2. Assign extension 1000 on button1 of user3.
Try to delete all the extensions together.
Workaround: Delete the extensions one by one.
|
CSCta31020
|
Whisper intercom does not throw error while editing an invalid entry.
|
Symptom: No error message while editing invalid Whisper Intercom entry.
Conditions: Whisper intercom dashboard should have invalid entry. Invalid entry should be created via the CLI.
Workaround: There is no workaround.
|
CSCta60741
|
Unable to add inspect rule to self zone when editing ZBF.
|
Symptom: Inspect rule does not get configured correctly for the SSL VPN Passthrough.
Conditions: Configure ZBF and then configure SSL VPN. The inspect rule does not get configured correctly. This is due to an IOS bug.
Workaround: There is no workaround.
|
CSCta77317
|
Analog Trunk window not closing on clicking the OK button.
|
Symptom: Go to Configure > Voice > PSTN Trunks > Analog Trunks. The Edit screen does not close when the OK button is clicked without making any changes.
Conditions: Go to Configure > Voice > PSTN Trunks > Analog Trunks screen. Select an entry, and then click Edit. Without making any changes, click OK. The dialog box does not close.
Workaround: Click Cancel button.
|
CSCta77454
|
Adhoc Conference update with SSH port blocked throws unwarranted error.
|
Symptom: Although Discovery is successful with SSH port blocked, updates on Adhoc Conference fail as interactive commands use SSH protocol. The error message does not indicate that the SSH port is blocked.
Conditions: Modification of Adhoc Conference parameters fail with SSH port blocked and the error message does not indicate the cause.
Workaround: Unblock the SSH port for any transport/communication errors on Adhoc Conference.
Further Problem Description: The Discovery process on Cisco CP is successful with SSH port blocked but features like Adhoc Conference use DSPs which interact using SSH ports. When the SSH port is blocked, all such interactions fail and hence updates on Adhoc Conference profile are not successful.The error message generated does not communicate the cause.
|
CSCtb05983
|
Multiple delete fails in offline mode community dashboard.
|
Symptom: Devices do not disappear from the community table immediately after deleting them.
Conditions: Select multiple devices in the offline mode and press Delete.
Workaround: Delete the devices one by one.
Or
Refresh the community table after all the devices are deleted.
|
CSCtb81205
|
Location to download SDM IPS packages needs to be changed.
|
Symptom: Latest SDM/CP packages for IPS cannot be auto downloaded using Cisco CP.
Conditions: If the user clicks "Download" option from IPS, the latest SDM/CP package will not be downloaded. Only the IOS-CLI package will be downloaded.
Workaround: Manually download the package from CCO and use it in Cisco CP for configuration or import options.
|
CSCtb58966
|
Reload of router unsuccessful after deploying license.
|
Symptom: Reload of device unsuccessful after deploying license or when using 'Reload router' button from License Management > Dashboard window.
Conditions: This is seen with devices with an AP module that requires an input to the following interactive command.
cisco881GW#reload
Do you want to reload the internal AP? [yes/no]:
Workaround: Manually reload the router for the license deployment to take effect and re-discover the router.
|
CSCtb43408
|
Dialer persistent config conflicts with Do Not Configure Now in wizard.
|
Symptom: No dialer persistent config delivered to the router.
Conditions: Both dialer persistent and Do Not Configure Now specified.
Workaround: There is no workaround.
|
CSCtb33162
|
Only the last chat script is removed when multiple chat is configured.
|
Symptom: Only the last chat script gets removed upon clicking the delete button for the specified interface.
Conditions: Configure multiple chat script under Dialer tab in edit mode.
Workaround: There is no workaround.
|
CSCta71627
|
Dialer list configuration removed after GSM wizard configuration.
|
Symptom: Previous configured dialer-list gets removed.
Conditions: There are two GSM interfaces, one is pre configured with dialer-list 2. While using the wizard to configure the second interface, dialer-list 2 get removed.
|
CSCsx05868
|
Unable to upload CME phone load tar file.
|
Symptom: In Cisco Configuration Professional, while trying to upload phone load tar file from the Voice > Phone Firmware feature, the upload may fail after some upload progress.
Conditions: On the device, if <CmdBold>exec-timeout</CmdBold> is not set under <CmdBold>line vty</CmdBold> configurations, or if <CmdBold>exec-timeout</CmdBold> is set with a smaller timeout value, then phone load upload may fail.
Workaround: On the device, under all <CmdBold>line vty</CmdBold> configs, set <CmdBold>exec-timeout</CmdBold> config with proper timeout value. For example:
vty line 0 4
exec-timeout 25 0
exit
Further Problem Description: exec-timeout is used to set the interval that the EXEC command interpreter waits until user input is detected. If no input is detected during that interval, the EXEC facility returns the terminal to the idle state and disconnects the incoming session.
A big size phone load tar file may take some time to get uploaded on the device's flash. So to avoid any error during upload, exec-timeout should be set with a value greater than the time taken to upload a big tar file.
If exec-timeout is set as 0 0, then vty lines may get blocked if the session is not exited or closed properly.
|
CSCtc30671
|
Issues with network object ACL groups
|
Symptom: The ACL network object groups do not get listed under the summary screen after creation.
The ACL object group created under one device gets listed under a different device.
The network object group created under a device cannot be applied under the ACL rule.
Conditions: The ACL network object groups do not get listed under the summary screen after creation. The ACL object group created under one device gets listed under a different device.
This problem is seen when more than one device is discovered.
Workaround: Rediscover the devices under Cisco CP.
|
Related Documentation
Table 14 describes the related documentation available for Cisco Configuration Professional.
Table 15 Cisco Configuration Professional Documentation
Document Title
|
Available Formats
|
Readme First for
Cisco Configuration Professional
|
This document is available in the following locations:
•On Cisco.com.
•On the product CD-ROM in the Documentation folder.
|
Cisco Configuration Professional Quick Start Guide
|
This guide is available in the following locations:
•On Cisco.com.
•On the product CD-ROM in the Documentation folder.
|
Cisco Configuration Professional Getting Started Guide
|
This guide is available in the following locations:
•On Cisco.com.
•On the product CD-ROM in the Documentation folder.
•During the installation process, just before you have finished installing the product, you are provided the option to read the Getting Started guide.
|
Cisco Configuration Professional User Guide
|
This guide is available in the following locations:
•On Cisco.com.
•Accessible from Online help.
|
Cisco Configuration Professional Express User Guide
|
This guide is available in the following locations:
•On Cisco. com.
•Accessible from Online help.
|
Release Notes for
Cisco Configuration Professional
|
This document is available in the following location:
•On Cisco.com.
|
Release Notes for
Cisco Configuration Professional Express
|
This document is available in the following location:
•On Cisco.com.
|
Note For information on obtaining documentation and technical assistance, product security, and additional information, see What's New, which also lists new and revised documents each month.
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
CCDE, CCENT, CCSI, Cisco Eos, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco Nurse Connect, Cisco Pulse, Cisco StackPower, Cisco StadiumVision, Cisco TelePresence, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, and Flip Gift Card are service marks; and Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Fast Step, Follow Me Browsing, FormShare, GainMaker, GigaDrive, HomeLink, iLYNX, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, Laser Link, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerKEY, PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect, ROSA, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0908R)
Copyright © 2009 Cisco Systems, Inc. All rights reserved.
Feedback
