-
Cisco IOS Voice Command Reference - S commands
-
sccp through service-type call-check
-
session through sgcp tse payload
-
show aal2 profile through show call filter match-list
-
show call history fax through show debug condition
-
show dial-peer through show gatekeeper zone prefix
-
show gateway through show modem relay statistics
-
show mrcp client session active through show sip dhcp
-
show sip service through show trunk hdlc
-
show vdev through show voice statistics memory-usage
-
show voice trace through shutdown (voice-port)
-
signal through srv version
-
ss7 mtp2-variant through switchover method
-
Index
-
Feedback
Contents
show gateway through show modem relay statistics
- show gateway
- show h323 calls preserved
- show h323 gateway
- show h323 gateway prefixes
- show http client cache
- show http client cache
- show http client cookie
- show http client history
- show http client secure status
- show http client statistics
- show interface dspfarm
- show interfaces cable-modem
- show iua as
- show iua asp
- show media resource status
- show mediacard
- show mgcp
- show mgcp connection
- show mgcp endpoint
- show mgcp nas
- show mgcp profile
- show mgcp srtp
- show mgcp statistics
- show modem relay statistics
show gateway
Command History
Release
Modification
11.3(6)NA2
This command was introduced.
12.0(5)T
The display format was modified for H.323 Version 2.
12.1(5)XM2
This command was implemented on the Cisco AS5350 and Cisco AS5400.
12.2(4)T
This command was not supported on the Cisco AS5300, Cisco AS5350, and Cisco AS5400 in this release.
12.2(2)XB1
This command was implemented on the Cisco AS5850.
12.2(11)T
This command was integrated into Cisco IOS Release 12.2(11)T.
Examples
The following sample output shows the report that appears when the gateway is not registered with a gatekeeper:
Router# show gateway Gateway gateway1 is not registered to any gatekeeper Gateway alias list H323-ID gateway1 H323 resource thresholding is Enabled but NOT Active H323 resource threshold values: DSP: Low threshold 60, High threshold 70 DS0: Low threshold 60, High threshold 70This following sample output indicates that an E.164 address has been assigned to the gateway:
Router# show gateway Gateway gateway1 is registered to Gatekeeper gk1 Gateway alias list E.164 Number 5551212 H323-ID gateway1The following sample output shows the report that appears when the gateway is registered with a gatekeeper and H.323 resource threshold reporting is enabled with the resource threshold command:
Router# show gateway Gateway gateway1 is registered to Gatekeeper gk1 Gateway alias list H323-ID gateway1 H323 resource thresholding is Enabled and Active H323 resource threshold values: DSP: Low threshold 60, High threshold 70 DS0: Low threshold 60, High threshold 70The following sample output shows the report that appears when the gateway is registered with a gatekeeper and H.323 resource threshold reporting is disabled with the no resource threshold command:
Router# show gateway Gateway gateway1 is registered to Gatekeeper gk1 Gateway alias list H323-ID gateway1 H323 resource thresholding is DisabledField descriptions should be self-explanatory.
show h323 calls preserved
To display data about active H.323 VoIP preserved calls, use the show h323 calls preserved command in user EXEC or privileged EXEC mode.
Usage Guidelines
The show h323 calls preserved command displays data per preserved call. Only active calls are displayed; preserved call history is not.
If translation rules are configured, the value displayed in the "Calling Number" field may have been translated by a gateway. Gateways handle called number values as the numbers to which calls are routed.
The "CallID" field displays the shorter form of the 16-octet, globally-unique connection ID that is allocated for each call leg. The show call active voice brief command also displays a shorter form of the CallID value (part of the third octet and the fourth octet). The longer form of the CallID value is output by the show call active voice command.
The CallID value can be used to refer to a call leg associated with the CallID when issuing other voice commands on the gateway, such as the show voice call status command and the clear call voice command.
An output value of -1 displayed in the "H225 FD" or "H245 FD" field denotes that the call was preserved due to an error detected on the H.225.0 connection. The actual H.225.0 socket file descriptor used for this call can be found from the syslog message that was output when this call was preserved.
To obtain more information about a call, you can also use the show call active voice command. Calls can be cleared with the clear call voice causecode command.
Examples
The following is sample output from the show h323 calls preserved command where one active call is preserved:
Router# show h323 calls preserved CallID = 11EC , Calling Number = , Called Number = 3210000 , RemoteSignallingIPAddress=9.13.0.26 , RemoteSignallingPort=49760 , RemoteMediaIPAddress=9.13.0.11 , RemoteMediaPort=17910 , Preserved Duration = 262 , Total Duration = 562 , H225 FD = -1 , H245 FD = -1The table below provides an alphabetical listing of the fields displayed in the output of the show h323 calls preserved command and a description of each field.
Table 1 show h323 calls preserved Field Descriptions Field
Description
Called Number
The phone number entered by the caller.
CallID
The shortened name for connection ID displayed in the show call active voice brief command.
H225 FD
The file descriptor number of the H.225.0 TCP socket.
H245 FD
The file descriptor number of the H.245 TCP socket.
Preserved Duration
The time in seconds that the call has been preserved.
RemoteMediaIPAddress
The remote media IP address.
RemoteMediaPort
The remote media IP address.
RemoteSignallingIPAddress
The remote signaling IP address.
RemoteSignallingPort
The remote signaling port.
Total Duration
The time in seconds of the phone call.
Related Commands
Command
Description
call preserve
Enables the preservation of H.323 VoIP calls.
clear call voice
Clears one or more voice calls detected as inactive because there is no RTP or RTCP activity.
show call active voice
Displays call information for voice calls in progress.
show voice call
Displays the call status for voice ports on the Cisco router.
show h323 gateway
To display statistics for H.323 gateway messages that have been sent and received and to display the reasons for which H.323 calls have been disconnected, use the show h323 gateway command in privileged EXEC mode.
Syntax Description
cause -code stats
(Optional) Output displays the disconnect cause codes that the H.323 subsystem has received. A disconnect can originate either from the far-end gateway or from the opposite call leg on the local gateway.
h225
(Optional) Output lists cumulative counts of the number of H.225 messages that have been sent and received since the counters were last cleared.
ras
(Optional) Output lists the counters for Registration, Admission, and Status (RAS) messages that have been sent to and received from the gatekeeper since the counters were last cleared.
Command Default
To display statistics for all the options, use this command without any of the optional keywords.
Examples
In the following example from a Cisco 3640 router, this command is used without keywords to display the statistics for all the options. See the tables below for descriptions of the fields.
Router# show h323 gateway H.323 STATISTICS AT 01:45:55 H.225 REQUESTS SENT RECEIVED FAILED Setup 0 5477 0 Setup confirm 5424 0 0 Alert 2734 0 0 Progress 2701 0 0 Call proceeding 5477 0 0 Notify 0 0 0 Info 0 0 0 User Info 0 0 0 Facility 2732 0 0 Release 5198 5313 241 Reject 0 0 0 Passthrough 0 0 0 H225 establish timeout 0 RAS failed 0 H245 failed 0 RAS MESSAGE REQUESTS SENT CONFIRMS RCVD REJECTS RCVD GK Discovery grq 0 gcf 0 grj 0 Registration rrq 130 rcf 130 rrj 0 Admission arq 5477 acf 5477 arj 0 Bandwidth brq 0 bcf 0 brj 0 Disengage drq 5439 dcf 5439 drj 0 Unregister urq 0 ucf 0 urj 0 Resource Avail rai 0 rac 0 Req In Progress rip 0 RAS MESSAGE REQUESTS RCVD CONFIRMS SENT REJECTS SENT GK Discovery grq 0 gcf 0 grj 0 Registration rrq 0 rcf 0 rrj 0 Admission arq 0 acf 0 arj 0 Bandwidth brq 0 bcf 0 brj 0 Disengage drq 0 dcf 0 drj 0 Unregister urq 0 ucf 0 urj 0 Resource Avail rai 0 rac 0 Req In Progress rip 0 DISC CAUSE CODE FROM OTHER PEER FROM H323 PEER 16 normal call clearing 66 5325 31 normal, unspecified 1 0 34 no circuit 31 0 41 temporary failure 3 0 44 no requested circuit 13 0In the following example from a Cisco 3640 router, this command is used with the cause-code stats keyword to display the disconnect cause codes that the H.323 subsystem has received. A disconnect can originate either from the far-end gateway or from the opposite call leg on the local gateway. Only the nonzero cause-code counts are displayed.
Router# show h323 gateway cause-code stats CAUSE CODE STATISTICS AT 01:40:25 DISC CAUSE CODE FROM OTHER PEER FROM H323 PEER 16 normal call clearing 66 4976 31 normal, unspecified 1 0 34 no circuit 31 0 41 temporary failure 3 0 44 no requested circuit 13 0The table below describes significant fields shown in this output
Table 2 show h323 gateway cause-code stats Field Descriptions Field
Description
Column Headings:
DISC CAUSE CODE
Decimal value of the cause code, followed by the textual description.
FROM OTHER PEER
Number of disconnects that have been received from the opposite call leg for each cause code (for example, from a PRI T1 POTS peer or a Foreign exchange station [FXS] POTS peer).
FROM H323 PEER
Number of disconnects that have been received from the far-end gateway for each cause code.
Fields listed under the headings are self-explanatory.
In the following example from a Cisco 3640 router, this command is used with the h225 keyword to display the cumulative counts of the number of H.225 messages that were sent and received since the counters were last cleared.
Each row shows the sent, received, and failed counts for one type of H.225 request. If the counters have not been cleared, total counts are shown for the router since it was last reloaded.
Router# show h323 gateway h225 H.225 STATISTICS AT 00:44:57 H.225 REQUESTS SENT RECEIVED FAILED Setup 1654 0 0 Setup confirm 0 1654 0 Alert 0 828 0 Progress 0 826 0 Call proceeding 0 1654 0 Notify 0 0 0 Info 0 0 0 User Info 0 0 0 Facility 0 828 0 Release 1613 9 1 Reject 0 0 0 Passthrough 0 0 0 H225 establish timeout 0 RAS failed 1 H245 failed 0The table below describes significant fields shown in this output.
Table 3 show h323 gateway h225 Field Descriptions Field
Description
Column Headings:
H.225 REQUESTS
Types of H.225 messages.
SENT
Number of H.225 messages sent by the gateway.
RECEIVED
Number of H.225 messages received from a remote gateway or endpoint.
FAILED
Number of H.225 messages that could not be sent. A failure could occur if, for example, the H.323 subsystem tried to send an H.225 release request but the TCP socket had already been closed.
Fields:
Setup
Number of setup messages that were sent, that were received, or that could not be sent. This message is sent by a calling H.323 entity to indicate its desire to set up a connection to the called entity.
Setup confirm
Number of setup confirm messages that were sent, that were received, or that could not be sent. This message may be sent by an H.323 entity to acknowledge receipt of a setup message.
Alert
Number of alert messages that were sent, that were received, or that could not be sent. This message may be sent by the called user to indicate that called user alerting has been initiated. (In everyday terms, the "phone is ringing.")
Progress
Number of progress messages that were sent, that were received, or that could not be sent. This message may be sent by an H.323 entity to indicate the progress of a call.
Call proceeding
Number of call proceeding messages that were sent, that were received, or that could not be sent. This message may be sent by the called user to indicate that requested call establishment has been initiated and that no more call establishment information is accepted.
Notify
Number of notify messages that were sent, that were received, or that could not be sent.
Info
Number of information messages that were sent, that were received, or that could not be sent.
User Info
Number of user information messages that were sent, that were received, or that could not be sent. This message may be used to provide additional information for call establishment (for example, overlap signaling), to provide miscellaneous call-related information, or to deliver proprietary features.
Facility
Number of facility messages that were sent, that were received, or that could not be sent. This message is used to provide information on where a call should be directed or for an endpoint to indicate that the incoming call must go through a gatekeeper.
Release
Number of release complete messages that were sent, that were received, or that could not be sent. This message is sent by a gateway to indicate the release of the call if the reliable call signaling channel is open.
Reject
Number of reject messages that were sent, that were received, or that could not be sent.
Passthrough
Number of pass-through messages that were sent, that were received, or that could not be sent.
H225 establish timeout
Number of times the H.323 subsystem was unable to establish an H.225 connection to a remote gateway for a call.
RAS failed
Number of times an Admission Reject (ARJ) or Disengage Reject (DRJ) message is received from the gatekeeper. This counter should equal the arj + drj received counters shown in the show h323 gateway ras command output.
H245 failed
Number of times the H.323 subsystem was unable to create an H.245 tunnel for a call or was unable to send an H.245 message.
In the following example from a Cisco 3640 router, this command is used with the ras keyword to display the counters for Registration, Admission, and Status (RAS) messages that were sent to the gatekeeper and received from the gatekeeper. With the exception of the Resource Avail and Req In Progress messages, each RAS message has three variations: a request message, a confirm message, and a reject message. For example, for the Admission message type, there is an Admission Request (arq) message, an Admission Confirm (acf) message, and an Admission Reject (arj) message. The gateway sends the arq message, and the gatekeeper responds with either an acf or an arj message, depending on whether the gatekeeper confirms or rejects the admission request.
Each of the two tables that follow lists the same message types, with each row showing a different message type. The first table shows the requests sent, the confirms received, and the rejects received. The second table shows the requests received, the confirms sent, and the rejects sent. Some rows in the second table would apply only to the gatekeeper (for example, a gateway would never receive a Registration Request (rrq) message, send a Registration Confirmation (rcf) message, or send a Registration Rejection (rrj) message).
Router# show h323 gateway ras RAS STATISTIC AT 01:10:01 RAS MESSAGE REQUESTS SENT CONFIRMS RCVD REJECTS RCVD GK Discovery grq 3 gcf 1 grj 0 Registration rrq 73 rcf 73 rrj 0 Admission arq 3216 acf 3215 arj 1 Bandwidth brq 0 bcf 0 brj 0 Disengage drq 3174 dcf 3174 drj 0 Unregister urq 0 ucf 0 urj 0 Resource Avail rai 0 rac 0 Req In Progress rip 0 RAS MESSAGE REQUESTS RCVD CONFIRMS SENT REJECTS SENT GK Discovery grq 0 gcf 0 grj 0 Registration rrq 0 rcf 0 rrj 0 Admission arq 0 acf 0 arj 0 Bandwidth brq 0 bcf 0 brj 0 Disengage drq 0 dcf 0 drj 0 Unregister urq 0 ucf 0 urj 0 Resource Avail rai 0 rac 0 Req In Progress rip 0The table below describes significant fields shown in this output.
Table 4 show h323 gateway ras Field Descriptions Field
Description
Column Headings for the First Table:
RAS MESSAGE
Type RAS message.
REQUESTS SENT
Number of RAS request messages sent by the gateway to a gatekeeper.
CONFIRMS RCVD
Number of RAS confirmation messages received from a gatekeeper.
REJECTS RCVD
Number of RAS reject messages received from a gatekeeper.
Column Headings for the Second Table:
RAS MESSAGE
Type of RAS message.
REQUESTS RCVD
Number of RAS request messages received from a gatekeeper.
CONFIRMS SENT
Number of RAS confirmation messages sent by the gateway.
REJECTS SENT
Number of RAS reject messages sent by the gateway.
Fields:
GK Discovery
Gatekeeper Request (GRQ) message requests that any gatekeeper receiving it respond with a Gatekeeper Confirmation (GCF) message granting it permission to register. The Gateway Reject (GRJ) message is a rejection of this request, indicating that the requesting endpoint should seek another gatekeeper.
Registration
Registration Request (RRQ) message is a request from a terminal to a gatekeeper to register. If the gatekeeper responds with a Registration Confirmation (RCF) message, the terminal uses the responding gatekeeper for future calls. If the gatekeeper responds with a Registration Reject (RRJ) message, the terminal must seek another gatekeeper with which to register.
Admission
Admission Request (ARQ) message requests that an endpoint be allowed access to the packet-based network by the gatekeeper, which either grants the request with an Admission Confirmation (ACF) message or denies it with an Admission Reject (ARJ) message.
Bandwidth
Bandwidth Request (BRQ) message requests that an endpoint be granted a changed packet-based network bandwidth allocation by the gatekeeper, which either grants the request with a Bandwidth Confirmation (BCF) message or denies it with a Bandwidth Reject (BRJ) message.
Disengage
If sent from an endpoint to a gatekeeper, the Disengage Request (DRQ) message informs the gatekeeper that an endpoint is being dropped. If sent from a gatekeeper to an endpoint, the DRQ message forces a call to be dropped; such a request is not refused. The DRQ message is not sent directly between endpoints.
Unregister
UnRegistration Request (URQ) message requests that the association between a terminal and a gatekeeper be broken. Note that the URQ request is bidirectional; that is, a gatekeeper can request a terminal to consider itself unregistered, and a terminal can inform a gatekeeper that it is revoking a previous registration.
Resource Avail
Resource Availability Indication (RAI) message is a notification from a gateway to a gatekeeper of its current call capacity for each H-series protocol and data rate for that protocol. The gatekeeper responds with a Resource Availability Confirmation (RAC) message upon receiving an RAI message to acknowledge its reception.
Req In Progress
Request In Progress (RIP) message can be used by a gateway or gatekeeper when a response to a message cannot be generated within a typical retry timeout period. The RIP message specifies the time period after which a response should have been generated.
show h323 gateway prefixes
To display the status of the destination-pattern database and the status of the individual destination patterns, use the show h323 gateway prefixes command in privileged EXEC mode.
Usage Guidelines
Use the show h323 gateway prefixes command to display the destination patterns from the active plain old telephone service (POTS) dial peers, the current state of the destination pattern (whether they have been sent to or acknowledged by the gatekeeper), and whether advertisement of dynamic prefixes is enabled on the gateway.
Examples
The following command displays the status of the gateway’s destination-pattern database:
Router# show h323 gateway prefixes GK Supports Additive RRQ : True GW Additive RRQ Support Enabled : True Pattern Database Status : Active Destination Active Pattern Status Dial-Peers ================================================================ 1110509* ADD ACKNOWLEDGED 2 1110511* ADD ACKNOWLEDGED 2 23* ADD ACKNOWLEDGED 2The table below describes the significant fields shown in the display.
Table 5 show h323 gateway prefixes Field Descriptions Field
Description
Pattern Database Status
Status of the gateway’s destination-pattern database: active or inactive.
Status
Status of the destination pattern. The status can be one of the following values:
ADD PENDING--The gateway has a prefix that is waiting to be sent to the gatekeeper. Prefixes are sent only at the lightweight registration request(RRQ) RAS message schedule, which is every 30 seconds.
ADD SENT--The gateway sent the prefix to the gatekeeper and is waiting for it to be acknowledged by a registration confirm (RCF) RAS message.
ADD ACKNOWLEDGED--The gateway received an RCF message indicating that the gatekeeper accepted the prefix. This is the normal status when dynamic zone prefix registration is working properly.
ADD REJECTED--The gatekeeper did not accept the prefix and sent a registration reject(RRJ) RAS message. One reason for rejection could be that the gatekeeper already has this prefix registered for a different zone, either by static zone prefix configuration, or because another gateway in a different zone dynamically registered this prefix first.
DELETE PENDING--The prefix has gone out of service, for example, because the dial peer shut down, and the gateway is waiting to send an unregistration request (URQ) RAS message to the gatekeeper to remove it. URQ messages are sent at the lightweight RRQ schedule, which is every 30 seconds.
DELETE SENT--The gateway sent a URQ message to remove the prefix to the gatekeeper. There is no DELETE ACKNOWLEDGED status. If the prefix is subsequently brought back in service, the status goes back to ADD PENDING.
show http client cache
To display information about the entries contained in the HTTP client cache, use the show http client cache command in user EXEC or privileged EXEC mode.
Command History
Release
Modification
12.2(2)XB
This command was introduced on the Cisco AS5300, Cisco AS5350, and Cisco AS5400.
12.2(11)T
This command was integrated into Cisco IOS Release 12.2(11)T and implemented on the Cisco 3640 and Cisco 3660.
12.4(15)T
The command output was modified to display files cached with URLs of HTTP and HTTPS format in separate tables. The command output was modified to mask out values of the URL attributes when caching of query data returned from the HTTP server is enabled.
12.4(15)XY
A pound sign (#) was added next to the Age field in the command output to indicate entries marked stale manually.
12.4(20)T
This command was integrated into Cisco IOS Release 12.4(20)T
Usage Guidelines
For more information on HTTP caching, see the specification on which it is based: RFC 2616, Hypertext Transfer Protocol HTTP/1.1, June 1999, IETF.
Examples
The following is sample output from this command:
Router# show http client cache HTTP Client cached information ============================== Maximum memory pool allowed for HTTP Client caching = 100000 K-bytes Maximum file size allowed for caching = 10 K-bytes Total memory used up for Cache = 18837 Bytes Message response timeout = 10 secs Total cached entries = 5 Total non-cached entries = 0 Cached entries ============== Cached table entry 167, number of cached entries = 2 Request URL Ref FreshTime Age Size ----------- --- --------- --- ---- abc.com/vxml/menu.vxml 0 20 703 319 abc.com/vxml/opr.vxml 0 647424 646 2772 Cached table entry 171, number of cached entries = 1 Request URL Ref FreshTime Age Size ----------- --- --------- --- ---- onlineshop.com/catalog/advance.vxml 0 69077 1297649 3453 Cached table entry 172, number of cached entries = 1 Request URL Ref FreshTime Age Size ----------- --- --------- --- ---- theater.com/vxml/menu_main.vxml 0 86400 1297661 8734 Cached table entry 176, number of cached entries = 1 Request URL Ref FreshTime Age Size ----------- --- --------- --- ---- popcorn.com/menu/selection.vxml 1 20 7 3559In the following example, the set http client cache stale command was used to set all the entries in the HTTP client cache to stale. Stale entries are indicated by a pound sign (#) next to the Age field.
Router# show http client cache HTTP Client cached information ============================== Maximum memory pool allowed for HTTP Client caching = 20000 K-bytes Maximum file size allowed for caching = 1000 K-bytes Total memory used up for Cache = 37758 Bytes Message response timeout = 10 secs Total cached entries = 7 Total non-cached entries = 0 Cached entries ============== entry 142, 1 entries Ref FreshTime Age Size context --- --------- --- ---- ------- 0 30 53233 # 486 63D8FCC4 url: http://goa/TEST1.vxml entry 145, 1 entries Ref FreshTime Age Size context --- --------- --- ---- ------- 1 4001998 53218 # 151 0 url: http://win2003/TEST2.vxml entry 157, 1 entries Ref FreshTime Age Size context --- --------- --- ---- ------- 1 30 28 # 185 0 url: http://goa/TEST3.vxml entry 164, 1 entries Ref FreshTime Age Size context --- --------- --- ---- ------- 1 2231127 53233 # 1183 0 url: http://goa/audio/en_welcome.au entry 166, 2 entries Ref FreshTime Age Size context --- --------- --- ---- ------- 1 2231127 53233 # 4916 0 url: http://goa/audio/en_one.au 1 2231127 53229 # 4500 0 url: http://goa/audio/en_three.au entry 169, 1 entries Ref FreshTime Age Size context --- --------- --- ---- ------- 1 2231127 53229 # 7224 0 url: http://goa/audio/en_two.auThe table below describes the fields shown in this output.
Related Commands
Command
Description
http client cache memory
Configures the HTTP client cache.
http client cache refresh
Configures the HTTP client cache refresh time.
http client response timeout
Configures the HTTP client server response timeout.
set http client cache stale
Sets the status of all entries in the HTTP client cache to stale.
show http client connection
Displays current HTTP client connection information.
show http client cache
To display information about the entries contained in the HTTP client cache, use the show http client cache command in user EXEC or privileged EXEC mode.
Command History
Release
Modification
12.2(2)XB
This command was introduced on the Cisco AS5300, Cisco AS5350, and Cisco AS5400.
12.2(11)T
This command was integrated into Cisco IOS Release 12.2(11)T and implemented on the Cisco 3640 and Cisco 3660.
12.4(15)T
The command output was modified to display files cached with URLs of HTTP and HTTPS format in separate tables. The command output was modified to mask out values of the URL attributes when caching of query data returned from the HTTP server is enabled.
Usage Guidelines
For more information on HTTP caching, see the specification on which it is based: RFC 2616, Hypertext Transfer Protocol HTTP/1.1, June 1999, IETF.
Examples
The following is sample output from this command:
Router# show http client cache HTTP Client cached information ============================== Maximum memory pool allowed for HTTP Client caching = 10000 K-bytes (default) Maximum file size allowed for caching = 50 K-bytes (default) Total memory used up for Cache = 4271 Bytes Message response timeout = 10 secs Total cached entries = 2 Total non-cached entries = 0 Cached entries ============== entry 135, 2 entries Ref FreshTime Age Size context --- --------- --- ---- ------- 0 121393 557 1419 0 url: http://10.1.200.21/vxml/menu_main.vxml 1 121447 13 2119 0 url: https://10.1.200.21/catalog/advance.vxmlThe following is sample output from this command when caching of query data returned from the HTTP server is enabled using the http client cache query command. Note that values of the URL attributes are masked out with asterisks (*) to protect caller privacy.
Router# show http client cache HTTP Client cached information ============================== Maximum memory pool allowed for HTTP Client caching = 10000 K-bytes (default) Maximum file size allowed for caching = 50 K-bytes (default) Total memory used up for Cache = 5382 Bytes Message response timeout = 10 secs Total cached entries = 4 Total non-cached entries = 0 Cached entries ============== entry 135, 2 entries Ref FreshTime Age Size context --- --------- --- ---- ------- 0 121393 577 1419 0 url: http://10.1.200.21/vxml/menu_main.vxml 1 121447 13 2119 0 url: https://10.1.200.21/catalog/advance.vxml entry 170, 2 entries Ref FreshTime Age Size context --- --------- --- ---- ------- 0 86400 709 478 67117ABC url: https://www.somebankurl.com/scripts/login.php?user=*******&password=*** 0 86400 528 478 686324C4 url: https://www.somebankurl.com/scripts/login.php?user=********&password=*****The table below describes the fields shown in this output.
Related Commands
Command
Description
http client cache memory
Configures the HTTP client cache.
http client cache query
Enables caching of query data returned from the HTTP server.
http client cache refresh
Configures the HTTP client cache refresh time.
http client response timeout
Configures the HTTP client server response timeout.
show http client connection
Displays current HTTP client connection information.
show http client cookie
To display cookies that are stored by the HTTP client, use the show http client cookie command in privileged EXEC mode.
Usage Guidelines
Use the call-id argument to display cookies for a specific call; otherwise, this command displays cookies for all calls. Cookies are stored only for the duration of a call. When a call terminates, all associated cookies are deleted. If you use the call-id argument and the call is not active, cookies are not displayed and an error message indicates that the call is not active.
Use the show call active voice brief command to display the call-id for an active call.
Examples
The following is sample output from the show http client cookie command:
Router# show http client cookie id 144567 HTTP Client Cookies =================== TestCookieY==password Path=/ Domain=.cisco.com TestCookieX==username Path=/ Domain=.cisco.comThe output lists the name, path, and domain of the cookie. Field descriptions should be self-explanatory.
Related Commands
Command
Description
debug http client cookie
Displays debugging traces related to HTTP cookies.
http client cache memory
Configures the memory limits for the HTTP client cache.
http client cache refresh
Configures the refresh time for the HTTP client cache.
http client cookie
Enables the HTTP client to send and receive and cookies.
show call active voice brief
Displays a call information summary for active calls.
show http client cache
Displays current HTTP client cache information.
show http client history
To display a list of the last 20 requests made by the HTTP client to the server, use the show http client history command in user EXEC or privileged EXEC mode.
Usage Guidelines
For more information on HTTP caching, see the specification on which it is based: RFC 2616, Hypertext Transfer Protocol HTTP/1.1, June 1999, IETF.
Examples
The following is sample output from this command, showing the most recent GET and POST requests from the HTTP client to the server:
Router# show http client history POST http://example.com/servlets/account GET http://example.com/GetDigit.vxml GET http://example.com/form.vxml GET http://sample.com/menu.vxml POST http://sample.com/servlets/order GET http://sample.com/servlets/weather?city=SanFrancisco&state=CAOutput shows only requests. There are no field headings.
show http client secure status
To display the trustpoint and cipher suites that are configured in the HTTP client, use the show http client secure status command in user EXEC or privileged EXEC mode.
Usage Guidelines
This command displays the trustpoint and cipher suites configured in the HTTP client by the http client secure-trustpoint and http client secure-ciphersuite commands.
Examples
The following sample output shows that the trustpoint myca has all five cipher suites configured:
Router# show http client secure status HTTP Client Secure Ciphersuite: rc4-128-md5 rc4-128-sha 3des-cbc-sha des-cbc-sha null-md5 HTTP Client Secure Trustpoint: mycaThe table below describes the significant fields shown in the display.
Table 8 show http client secure status Field Descriptions Field
Description
HTTP Client Secure Ciphersuite
Cipher suites.
- 3des_cbc_sha--Triple DES (Data Encryption Standard) encryption and the SHA (Secure Hash Algorithm) integrity method.
- des_cbc_sha--DES encryption and the SHA integrity method.
- null_md5--NULL encryption and the MD5 (Message-Digest algorithm 5) integrity method.
- rc4_128_md5--RC4 (or ARCFOUR) encryption and the MD5 integrity method.
- rc4_128_sha--RC4 encryption and the SHA integrity method.
HTTP Client Secure Trustpoint
Trustpoint name.
show http client statistics
To display information about the communication between the HTTP server and the client, use the show http client statistics command in user EXEC or privileged EXEC mode.
Usage Guidelines
Use the data displayed by this command to determine whether the network topology between the HTTP server and client is properly designed and configured. To reset to zero all the counters that collect the information this command displays, use the clear http client statistics command.
Examples
The following sample output from this command shows statistics about the communication between the HTTP server and client:
Router# show http client statistics HTTP Client Statistics: ======================= Elapsed time: 759962960 msec Load Count: total load count = 6899220 total byte count = 26028731394 largest file size = 624742 bytes smallest file size = 374 bytes Server Response Time to Connect: longest response to connect = 10484 msec shortest response to connect = 24 msec Server Response Time to Load: longest response to load = 11936 msec shortest response to load = 20 msec File Load Time from Server: longest load time = 13124 msec shortest load time = 56 msec Server Connection Count: max connections = 23 established connections = 6901185 Load Rate: 1 hour : 123300000 bytes 1 min : 2055000 bytes 1 sec : 34250 bytes 1 msec : 34.25 bytes Individual Counts: app_requests = 8538451 app_callbacks = 8538451 200_OK_rsp = 8512959 other_rsp = 0 total_errors = 25492 client_timeouts = 25470 client_errs = 0 connect_errs/_timeouts = 7 msg_decode_errs = 0 msg_encode_errs = 0 msg_xmit_errs = 15 write_Q_full = 0 socket_rcv_errs = 0 supported_method_errs = 0 retries = 4645 late_responses = 0 out_of_memory = 0 mem_reallocs = 1206 msg_malloced = 0 event_malloced = 45 cache_freed_by_ager = 1565The table below describes the significant fields shown in the display.
Table 9 show http client statistics Field Descriptions Field
Description
Elapsed time
Time elapsed since the first HTTP request, in milliseconds (ms).
total load count
Number of API events.
total byte count
Total bytes downloaded from the server by API requests.
largest file size smallest file size
Size of largest and smallest files downloaded from the server, in bytes.
longest response to connect shortest response to connect
Longest and shortest time taken by the server to establish a network connection requested by the client, in ms.
longest response to load shortest response to load
Longest and shortest time taken by the server to fulfill a download request from the client, in ms.
longest load time shortest load time
Longest and shortest time taken by the server to complete downloading the entire file, in ms.
max connections
Maximum concurrent connections.
established connections
Number of currently active and previously established connections.
Load Rate
Downloading rate in bytes/hour, bytes/minute, bytes/second, and bytes/ms.
app_requests
Number of GET and POST requests.
app_callbacks
Number of callbacks to the application.
200_OK_rsp
Number of server messages with response code 200 OK or 304 Not Modified.
other_rsp
Number of server messages with a response code other than 200 and 304.
total_errors
Number of errors encountered by the client.
client_timeouts
Number of timeouts the client has experienced, for example, response timeouts.
client_errs
Number of client internal errors, for example, software errors.
connect_errs/_timeouts
Number of failed or broken connections.
msg_decode_errs
Number of server response messages for which the client failed to decode the headers.
msg_encode_errs
Number of send messages for which the client failed to encode the headers.
msg_xmit_errs
Number of send messages that the client failed to transmit to the server.
write_Q_full
Number of times that the client failed to enter a send message requested by an application into the transmit queue.
socket_rcv_errs
Number of socket read error events returned by TCP.
supported_method_errs
Number of unsupported methods requested by the application.
retries
Number of retransmitted messages.
late_responses
Number of messages that were decoded successfully but exceeded the timeout.
out_of_memory
Number of times that the client failed to allocate memory from Cisco IOS software.
mem_reallocs
Number of times that the client needed to readjust its buffer size because the server response message size exceeded the allocated buffer.
msg_malloced
Number of message buffers currently allocated for receiving messages from the server.
event_malloced
Number of event buffers currently allocated for application programming interface (API) requests.
cache_freed_by_ager
Number of HTTP client cache entries freed up by the background ager process.
show interface dspfarm
To display digital-signal-processor (DSP) information on the two-port T1/E1 high-density port adapter for the Cisco 7200 series, use the show interface dspfarmcommand inprivilegedEXEC mode.
Usage Guidelines
You can display the local time-division-multiplexing (TDM) cross-connect map by using the following form of this command: show interface dspfarm <x/y | x/y/z> dsp tdm..
Examples
The following is sample output from this command for port adapter slot 0 of chassis slot 3 on a Cisco 7200 series router:
Router# show interface dspfarm 3/0 DSPfarm3/0 is up, line protocol is up Hardware is VXC-2T1/E1 MTU 256 bytes, BW 12000 Kbit, DLY 0 usec, reliability 255/255, txload 4/255, rxload 1/255 Encapsulation VOICE, loopback not set C549 DSP Firmware Version:MajorRelease.MinorRelease (BuildNumber) DSP Boot Loader:255.255 (255) DSP Application:4.0 (3) Medium Complexity Application:3.2 (5) High Complexity Application:3.2 (5) Total DSPs 30, DSP0-DSP29, Jukebox DSP id 30 Down DSPs:none Total sig channels 120 used 24, total voice channels 120 used 0 0 active calls, 0 max active calls, 0 total calls 30887 rx packets, 0 rx drops, 30921 tx packets, 0 tx frags 0 curr_dsp_tx_queued, 29 max_dsp_tx_queued Last input never, output never, output hang never Last clearing of "show interface" counters never Queueing strategy:fifo Output queue 0/0, 0 drops; input queue 0/75, 0 drops 5 minute input rate 13000 bits/sec, 94 packets/sec 5 minute output rate 193000 bits/sec, 94 packets/sec 30887 packets input, 616516 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 30921 packets output, 7868892 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped outThe table below describes significant fields shown in this output.
Table 10 show interface dspfarm Field Descriptions Field
Description
DSPfarm3/0 is up
DSPfarm interface is operating. The interface state can be up, down, or administratively down.
Line protocol is
Whether the software processes that handle the line protocol consider the line usable or if it has been taken down by an administrator.
Hardware
Version number of the hardware.
MTU
256 bytes.
BW
12000 kilobits.
DLY
Delay of the interface, in microseconds.
Reliability
Reliability of the interface as a fraction of 255 (255/255 is 100% reliability, calculated as an expediential average over 5 minutes).
Txload
Number of packets sent.
Rxload
Number of packets received.
Encapsulation
Encapsulation method assigned to the interface.
Loopback
Loopback conditions.
C549 DSP Firmware Version
Version of DSP firmware installed.
DSP Boot Loader
DSP boot loader version.
DSP Application
DSP application code version.
Medium Complexity Application
DSP Medium Complexity Application code version.
High Complexity Application
DSP High Complexity Application code version.
Total DSPs
Total DSPs that are equipped in the PA.
DSP0-DSP
DSP number range.
Jukebox DSP id
Jukebox DSP number.
Down DSPs
DSPs not in service.
Total sig channels...used...
Total number of signal channels used.
Total voice channels...used...
Total number of voice channels used.
Active calls
Number of active calls.
Max active calls
Maximum number of active calls.
Total calls
Total number of calls.
Rx packets
Number of received (rx) packets.
Rx drops
Number of rx packets dropped at PA.
Tx packets
Number of transmit (tx) packets.
Tx frags
Number of tx packets that were fragmented.
Curr_dsp_tx_queued
Number of tx packets that are being queued at host DSP queues.
Max_dsp_tx_queued
The max total tx packets that were queued at host DSP queues.
Last input
Number of hours, minutes, and seconds since the last packet was successfully received by an interface. Useful for knowing when a dead interface failed. This counter is updated only when packets are process switched and not when packets are fast switched.
Output
Number of hours, minutes, and seconds since the last packet was successfully sent by the interface. Useful for knowing when a dead interface failed. This counter is updated only when packets are process switched and not when packets are fast switched.
Output hang
Number of hours, minutes, and seconds (or never) since the interface was last reset because of a transmission that took too long. When the number of hours in any of the "last" fields exceeds 24 hours, the number of days and hours is printed. If that field overflows, asterisks (**) are printed.
Last clearing of "show interface" counters
Number of times the "show interface" counters were cleared.
queueing strategy
First-in, first-out queueing strategy (other queueing strategies you might see are priority-list, custom-list, and weighted fair).
Output queue
Number of packets in output queue.
Drops
Number of packets dropped because of a full queue.
Input queue
Number of packets in input queue.
Minute input rate
Average number of bits and packets received per minute in the past 5 minutes.
Bits/sec
Average number of bits sent per second.
Packets/sec
Average number of packets sent per second.
Packets input
Total number of error-free packets received by the system.
Bytes
Total number of bytes, including data and MAC encapsulation, in the error free packets received by the system.
No buffer
Number of received packets discarded because there was no buffer space in the main system. Compare with ignored count. Broadcast storms on Ethernets and bursts of noise on serial lines are often responsible for no-input-buffer events.
Received...broadcasts
Total number of broadcast or multicast packets received by the interface.
Runts
Number of packets that are discarded because they are smaller than the minimum packet size for the medium. For instance, any Ethernet packet that is less than 64 bytes is considered a runt.
Giants
Number of packets that are discarded because they exceed the maximum packet size for the medium. For instance, any Ethernet packet that is greater than 1518 bytes is considered a giant.
Throttles
Number of times the receiver on the port was disabled, possibly because of buffer or processor overload.
Input errors
Number of packet input errors.
CRC
Cyclic redundancy checksum generated by the originating LAN station or far end device does not match the checksum calculated from the data received. On a LAN, this usually indicates noise or transmission problems on the LAN interface or the LAN bus itself. A high number of CRCs is usually the result of collisions or a station sending bad data. On a serial link, CRCs usually indicate noise, gain hits, or other transmission problems on the data link.
Frame
Number of packets received incorrectly having a CRC error and a noninteger number of octets. On a serial line, this is usually the result of noise or other transmission problems.
Overrun
Number of times the serial receiver hardware was unable to hand received data to a hardware buffer because the input rate exceeded the ability of the receiver to handle the data.
Ignore
Number of received packets ignored by the interface because the interface hardware ran low on internal buffers. These buffers are different from the system buffers mentioned previously in the buffer description. Broadcast storms and bursts of noise can cause the ignored count to be incremented.
Abort
Illegal sequence of one bits on the interface.
Packets output
Total number of messages sent by the system.
Bytes
Total number of bytes, including data and MAC encapsulation, sent by the system.
Underruns
Number of times that the far end transmitter has been running faster than the near-end router’s receiver can handle.
Output errors
Sum of all errors that prevented the final transmission of datagrams out of the interface being examined. Note that this value might not balance with the sum of the enumerated output errors; some datagrams can have more than one error, and others can have errors that do not fall into any of the specifically tabulated categories.
Collisions
Number of messages re-sent because of an Ethernet collision. Collisions are usually the result of an overextended LAN (Ethernet or transceiver cable too long, more than two repeaters between stations, or too many cascaded multiport transceivers). A packet that collides is counted only once in output packets.
Interface resets
Number of times an interface has been completely reset. Resetting can happen if packets queued for transmission were not sent within a certain interval. If the system notices that the carrier detect line of an interface is up, but the line protocol is down, it periodically resets the interface in an effort to restart it. Interface resets can also occur when an unrecoverable interface processor error occurs, or when an interface is looped back or shut down.
Output buffer failures
Number of failed buffers.
Output buffers swapped out
Number of buffers swapped out.
show interfaces cable-modem
To display statistics for all interfaces configured on the cable modem port and to define Hybrid Fiber-Coax (HFC) statistics on the modem, use the show interfaces cable-modem command in privileged EXEC mode.
Examples
The following example shows the HFC state on the modem. The resulting output varies, depending on the network for which an interface has been configured.
Router# show interfaces cable-modem 0/1/0 cable-modem0/1/0 is up, line protocol is up HFC state is OPERATIONAL, HFC MAC address is 00d0.59e1.2073 Hardware is Cable modem, address is 0014.f26d.10b2 (bia 0014.f26d.10b2) Internet address is 00.0.0.01/1 MTU 1500 bytes, BW 1544 Kbit, DLY 6470 usec, reliability 255/255, txload 247/255, rxload 246/255 Encapsulation ARPA, loopback not set ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:01, output 00:00:00, output hang never Last clearing of "show interface" counters 00:07:03 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 83594 Queueing strategy: Class-based queueing Output queue: 61/1000/64/83594 (size/max total/threshold/drops) Conversations 2/5/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 232 kilobits/sec 30 second input rate 2581000 bits/sec, 987 packets/sec 30 second output rate 1585000 bits/sec, 639 packets/sec HFC input: 0 errors, 0 discards, 0 unknown protocols 0 flow control discards HFC output: 0 errors, 0 discards 304582 packets input, 105339474 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 228195 packets output, 78392605 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped outThe table below describes the significant fields shown in the display.
Table 11 show interfaces cable-modem Field Descriptions HFC State Values
Description
HFC state is OPERATIONAL
Current HFC state on the modem.
HFC MAC address
The HFC MAC address for this modem.
Hardware is Cable modem
Hardware type.
Internet address
The IP address for this modem.
MTU
Total MTU usage in bytes, kilobits, user seconds. Describes reliability, transmit load, and receiver load.
Encapsulation ARPA, loopback not set
Encapsulation type and whether loopback is set.
ARP type: ARPA, ARP Timeout
ARP type and timeout parameters.
Last input, output, output hang
Most recent input and output statistics.
Last clearing of "show interface" counters
Most recent usage of show interface command counters.
Input queue, Total output drops
Input queue and output drop statistics in the following format: size/max/drops/flushes.
Queueing strategy: Class-based queueing
Queueing type. In this case, class-based queueing.
Output queue
Output queue statistics in the following format: size/max total/threshold/drops.
Conversations
Type and number of conversations in the following format: active/max active/max total.
Reserved Conversations
Number of reserved conversations in the following format: allocated/max allocated.
Available Bandwidth
Allotted bandwidth in kilobits per second.
input rate, packets
Input rate and number of packets in bits per second, packets per second.
output rate, packets
Output rate and number of packets in bits per second, packets per second.
HFC input, output
HFC input statistics in the following format: errors, discards, unknown protocols, flow control discards.
packets input
Number of packets in bytes, with or without buffer.
Received broadcasts, runts, giants, throttles
Number of broadcasts, runts, giants, and throttles.
input errors
Number and type of input errors in the following format: cyclic redundancy check (CRC), frame, overrun, ignored.
packets output
Number of packets output in bytes and underruns.
output errors, collisions, interface resets
Number of output errors, collisions, and interface resets.
babbles, late collision, deferred
Number of babbles, late collisions, and deferred packets.
lost carrier, no carrier
Carrier statistics.
output buffer failures, output buffers swapped out
Buffer statistics.
The HFC state is the Data Over Cable Service Interface Specification (DOCSIS) state for the cable modem connection to the cable modem termination system (CMTS). The table below describes HFC state values.
Table 12 HFC State Values HFC State Values
Description
NOT_READY
Cable modem controller is resetting.
NOT_SYNCHRONIZED
Cable modem controller is starting the downstream frequency scan.
PHY_SYNCHRONIZED
Cable modem controller locked the downstream signal and is collecting the upstream channel parameter information.
US_PARAMETERS_ACQUIRED
Cable modem controller collected upstream channel parameter information and is trying to lock upstream frequency.
RANGING_COMPLETE
Cable modem controller received the CMTS range response, has finished downstream/upstream lock process, and is initializing IP.
IP_COMPLETE
Cable modem controller has IP information.
WAITING_FOR_DHCP_OFFER
Cable modem controller is sending a Dynamic Host Configuration Protocol (DHCP) request to the CMTS.
WAITING_FOR_DHCP_RESPONSE
Cable modem controller is waiting for a DHCP response from the CMTS.
WAITING_FOR_TIME_SERVER
Cable modem controller is starting the time of day (ToD) service.
TOD_ESTABLISHED
Cable modem controller has received the ToD packet and has synchronized its local time.
WAITING_FOR_TFTP
Cable modem controller is downloading its running configuration from the CMTS-defined TFTP server.
PARAM_TRANSFER_COMPLETE
Cable modem controller has completed transferring its running configuration.
REGISTRATION_COMPLETE
Cable modem controller has sent out its registration request, and CMTS has accepted it.
REFUSED_BY_CMTS
Cable modem controller registration request has been rejected by CMTS.
FORWARDING_DENIED
Cable modem controller registration to CMTS was successful, but network access is disabled in the running configuration.
OPERATIONAL
Cable modem controller is ready for service.
UNKNOWN
Cable modem controller is an undefined state
The table below lists input error descriptions.
Table 13 Input Error Description Input Error
Description
errors
The total number of input packets discarded on the cable modem controller.
discards
The number of input packets discarded due to a momentary lack of resources.
unknown protocols
The number of input packets discarded because they have unsupported or unknown protocol values.
flow control discards
The number of input packets discarded because the cable modem controller overflowed transferring packets to the router.
The table below lists output error descriptions.
show iua as
To display information about the current condition of an application server (AS), use the show iua as command in privileged EXEC mode.
Command History
Release
Modification
12.2(4)T
This command was introduced.
12.2(8)T
This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.
12.2(11)T
This command was implemented on the Cisco 2420, Cisco 2600 series, Cisco 3600 series, Cisco 3700 series, Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850.
Usage Guidelines
Use the show iua as all command to find the failover timer value. You need to know the current failover timer value before you changeit to fit your application.
Examples
The following sample output from this command shows that the current state of the AS (as1) is active and that there are four PRI interfaces configured to use this AS:
Router# show iua as all Name of AS :as1 Total num of ASPs configured :2 asp1 asp2 Current state : ACTIVE Active ASP :asp1 Number of ASPs up :1 Fail-Over time : 4000 milliseconds Local address list : 10.1.2.345 10.2.3.456 Local port:2139 Interface IDs registered with this AS Interface ID 0 (Dchannel0) 3 (Dchannel3) 2 (Dchannel2) 1 (Dchannel1)The table below describes significant fields shown in the output.
Table 15 show iua as all Field Descriptions Field
Description
Name of AS: 1
Name of the AS.
Total num of ASPs configured :2
asp1 asp2
Total number of application server processes (ASPs) configured.
Current state : ACTIVE
The possible states are ACTIVE, INACTIVE, and DOWN.
Active ASP :asp1
Shows the active ASP.
Number of ASPs up :1
If two ASPs are up, then the one that is not active is in standby mode.
Fail-Over time : 4000 milliseconds
Default is 4000 ms, although the value can also be configured through the CLI under AS.
Local address list : 10.1.2.345 10.2.3.456
Configured by the user.
Local port:2139
Configured by the user.
Interface IDs registered with this AS
Interface id
0 (Dchannel0)
3 (Dchannel3)
2 (Dchannel2)
1 (Dchannel1)
The D channels that are bound to this AS.
Related Commands
Command
Description
clear ip sctp statistics
Clears statistics counts for SCTP.
show ip sctp association list
Displays a list of all current SCTP associations.
show ip sctp association parameters
Displays the parameters configured for the association defined by the association ID.
show ip sctp association statistics
Displays the current statistics for the association defined by the association ID.
show ip sctp errors
Displays error counts logged by SCTP.
show ip sctp instances
Displays the currently defined SCTP instances.
show ip sctp statistics
Displays the overall statistics counts for SCTP.
show isdn
Displays information about memory, Layer 2 and Layer 3 timers, and the status of PRI channels.
show iua asp
Displays information about the current condition of an ASP.
show iua asp
To display information about the current condition of an application server process (ASP), use the show iua asp command in privileged EXEC mode.
Command History
Release
Modification
12.2(4)T
This command was introduced.
12.2(8)T
This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.
12.2(11)T
This command was implemented on the Cisco AS5300.
12.2(15)T
This command was integrated into Cisco IOS Release 12.2(15)T on the Cisco 2420, Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series; and Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 network access server (NAS) platforms.
Usage Guidelines
This command establishes Stream Control Transmission Protocol (SCTP) associations. There can only be a maximum of two ASPs configured per application server (AS).
Examples
The following typical output for the show iua asp all command shows that the current state of the ASP (asp1) is active. This command also gives information about the SCTP association being used by this ASP.
Router# show iua asp all Name of ASP :asp1 Current State of ASP:ASP-Active Current state of underlying SCTP Association IUA_ASSOC_ESTAB , assoc id 0 SCTP Association information : Local Receive window :9000 Remote Receive window :9000 Primary Dest address requested by IUA 10.11.2.33 Effective Primary Dest address 10.11.2.33 Remote address list :10.22.3.44 Remote Port :9900 Statistics : Invalid SCTP signals Total :0 Since last 0 SCTP Send failures :0The table below describes significant fields shown in this output.
Table 16 show iua asp all Field Descriptions Field
Description
Name of ASP: 1
Name of the application server process (ASP).
Current State of ASP: ASP-Active
The possible states are ACTIVE, INACTIVE, and DOWN.
Current state of underlying SCTP Association IUA_ASSOC_ESTAB , assoc id 0
States used for underlying SCTP association: IUA_ASSOC_ESTAB (association established) or IUA_ASSOC_INIT (association not established...attempting to initiate).
SCTP Association information :
Local Receive window :9000
Remote Receive window :9000
Configured by the user.
Primary Dest address requested by IUA 10.11.2.33
The IP address through which the current link is established.
Remote address list :10.22.3.44
Remote Port :9900
Configured by the user.
Statistics :
Invalid SCTP signals Total :0 Since last 0
SCTP Send failures :0
Information useful for seeing if errors are happening with the SCTP connection.
Related Commands
Command
Description
clear ip sctp statistics
Clears statistics counts for SCTP.
show ip sctp association list
Displays a list of all current SCTP associations.
show ip sctp association parameters
Displays the parameters configured for the association defined by the association ID.
show ip sctp association statistics
Displays the current statistics for the association defined by the association ID.
show ip sctp errors
Displays error counts logged by SCTP.
show ip sctp instances
Displays the currently defined SCTP instances.
show ip sctp statistics
Displays the overall statistics counts for SCTP.
show iua as
Displays information about the current condition of an AS.
show media resource status
To display the current media resource status, use the show media resource status command in privileged EXEC mode.
Examples
The following example displays the current media resource status:
Router# show media resource status Resource Providers: Resource Provider ID :: FLEX_DSPRM Status :: REGISTERED Service Profiles MTP :: TRANSCODING :: 6 11 CONFERENCING :: 10 Applications : Application ID : SCCP, Status : REGISTEREDThe table below describes significant fields shown in this output.
Table 17 show media resource status Field Descriptions Field
Description
MTP
Displays the profile numbers configured for MTP resources.
TRANSCODING
Displays the profile numbers configured for transcoding resources.
CONFERENCING
Displays the profile numbers configured for conferencing resources.
Status
Displays the current status of the profile.
Related Commands
Command
Description
dsp services dspfarm
Configures DSP farm services for a specified voice card.
dspfarm profile
Enters DSP farm profile configuration mode and defines a profile for DSP farm services.
show dspfarm profile
Displays configured DSP farm profile information for a Cisco CallManager group.
show mediacard
To display configuration information about media card conferencing, transcoding, Media Termination Points (MTPs) and Digital Signal Processors (DSPs), use the show mediacard command in privileged EXEC mode.
Syntax Description
slot
Specifies the slot number of the card to be displayed. Valid values are from 1 to 4.
conference
(Optional) Displays information on ad-hoc conferences.
connections
(Optional) Displays information on media card connections.
dsp number
(Optional) Displays information on the specified DSP resource pool. The numberargument ranges in value from 1 to 4.
Usage Guidelines
Use this command to display media card status, statistics, and configuration information.
Examples
The following is sample output for the show mediacard command:
Router# show mediacard 3 Media Card 3: WS-SVC-CMM-ACT Service: Adhoc/Meetme conference and MTP/Transcoding State: ENABLE DSP image version (all DSPs): 1.1(06), build: 1.1(06) DSP status: DSP 1 | DSP 2 | DSP 3 | DSP 4 -------|-------|-------|------- alive | alive | alive | alive Total 128 DSP channels, 1 active Resource pools | DSPs | Used by Active profile -----------------------------------|------|----------------------- Pool1 | 2 | 1 Pool2 | 1 | Pool3 | 1 | 2 Router# show mediacard 3 dsp 3 DSP image version (all DSPs): 1.1(06), build: 1.1(06) Card DSP status Chan status RxPkts TxPkts 3 3 alive 1 idle - - 2 idle - - 3 idle - - 4 idle - - 5 idle - - 6 idle - - 7 idle - - 8 idle - - 9 idle - - 10 idle - - 11 idle - - 12 idle - - 13 idle - - 14 idle - - 15 idle - - 16 idle - - 17 idle - - 18 idle - - 19 idle - - 20 idle - - 21 idle - - 22 idle - - 23 idle - - 24 idle - - 25 idle - - 26 idle - - 27 idle - - 28 idle - - 29 idle - - 30 idle - - 31 idle - - 32 idle - - Total 32 DSP channels, 0 active Router# show mediacard conference Id Slot/ RxPkts TxPkts RPort SPort Remote-Ip DSP/Ch 0 2/4/1 32024 16498 27004 27020 10.7.16.87 0 2/4/2 17368 17192 17582 17583 10.7.16.80 0 2/4/3 21904 16990 26155 26168 10.7.16.94 Total: 3 Router# show mediacard connections Id Type Slot/ RxPkts TxPkts RPort SPort Remote-Ip DSP/Ch 0 conf 3/4/1 24028 16552 0 0 10.7.16.87 Total: 1 Router# show mediacard connections Id Type Slot/ RxPktsTxPktsRPort SPort Remote-Ip DSP/Ch 0 mtp 3/1/1 16544 16488 1046 1046 10.1.2.15 0 mtp 3/1/2 19396 19662 1046 1046 10.1.80.50 0 mtp 3/1/3 17562 20122 626 626 10.1.2.15 0 mtp 3/1/4 17488 17328 626 626 10.1.80.5The table below describes the significant fields shown in the display.
show mgcp
To display values for Media Gateway Control Protocol (MGCP) parameters, use the show mgcp command in user EXEC or privileged EXEC mode.
show mgcp [ connection | endpoint | nas { dump slot port chan-number | info } | notify-entity | profile [name] | statistics ]
Syntax Description
connection
(Optional) Displays the active MGCP-controlled connections.
endpoint
(Optional) Displays the MGCP-controlled endpoints.
nas
(Optional) Displays Network Access Server (NAS) information.
dump
(Optional) Display MGCP data channel data.
slot
(Optional) Slot number.
port
(Optional) Port number.
chan-number
(Optional) Channel number.
info
(Optional) Displays MGCP data channel information.
notify-entity
(Optional) Displays MGCP notify entity information.
profile [name]
(Optional) Displays information about all the configured MGCP profiles.
statistics
(Optional) Displays MGCP statistics regarding received and transmitted network messages.
Command History
Release
Modification
12.1(1)T
This command was introduced on the Cisco AS5300.
12.1(3)T
This command was modified. Command output was updated to display additional gateway and platform information.
12.1(5)XM
This command was modified. Command output was updated to display additional gateway and platform information.
12.2(2)T
This command was implemented on the Cisco 7200 series.
12.2(2)XA
This command was modified. The profile keyword was added.
12.2(4)T
This command was integrated into Cisco IOS Release 12.2(4)T.
12.2(2)XB
This command was modified. Command output was enhanced to display the status of MGCP system resource check (SRC) call admission control (CAC) and Service Assurance Agent (SA Agent) CAC. (See the Cisco IOS Release 12.2(2)XB document MGCP VoIP Call Admission Control .)
The nas dump slot port channeland nas info keywords and arguments were added. Because the number of keywords increased, the command page for the show mgcp command was separated into the following command pages:
12.2(8)T
This command was integrated into Cisco IOS Release 12.2(8)T.
12.2(2)XN
This command was modified. Support for enhanced MGCP voice gateway interoperability was added to Cisco CallManager Version 3.1 for the Cisco 2600 series, Cisco 3600 series, and Cisco VG200 routers.
12.2(11)T
This command was integrated into Cisco IOS Release 12.2(11)T and Cisco CallManager Version 2.0. It was implemented on the Cisco AS5350, Cisco AS5400, Cisco AS5850, and Cisco IAD2420 series. The MGCP SGCP RSIP field was enhanced to show the status of the mgcp sgcp disconnected notifycommand.
12.2(13)T
This command was modified. Support was added for MGCP.
12.2(15)T
This command was implemented on Cisco 1751 and Cisco 1760 routers.
12.2(15)ZJ
This command was integrated into Cisco IOS Release 12.2(15)ZJ on the Cisco 26xxXM, Cisco 2691, Cisco 3640, Cisco 3640A, Cisco 3660, and Cisco 37xx routers.
12.3(2)T
This command was implemented on the Cisco 26xxXM, Cisco 2691, Cisco 3640, Cisco 3640A, Cisco 3660, and Cisco 37xx routers.
12.3(11)T
This command was modified. Command output was enhanced to display the enabled Secure Real-Time Transport Protocol (SRTP) package and enabled MGCP call-agent validation.
12.4(2)T
This command was modified. Command output was enhanced to display State Signaling Events (SSE) and Simple Packet Relay Transport (SPRT) configuration parameters.
12.4(11)T
This command was modified. The show mgcp command output was enhanced to display comedia-related configuration.
15.1(4)M
This command was integrated into Cisco IOS 15.1(4)M. The command output was enhanced to displays the configuration of the tone-package keywordin the MGCP- supported packages.
Usage Guidelines
This command provides high-level administrative information about the values configured for MGCP parameters on the router. For more specific information, use one of the optional keywords.
Use the show mgcp command to display SSE and SPRT parameters that have been configured to enable modem relay between IP secure telephone equipment (STE) and STE. The parameters are displayed only when the modem relay STE (mdste) package has been enabled using the mgcp package-capability mdste-packagecommand.
Use the show mgcp endpoint command to display a list of MGCP endpoint responses when the configuring Media Gateway Control Protocol Basic Rate Interface Backhaul Signaling with Cisco CallManager feature.
The BRI endpoints are displayed in a similar manner to the way analog (Plain Old Telephone service) endpoints are displayed. The existing functions used for the analog endpoints are invoked. This display is independent of the platforms; hence the changes are required in the common code only.
This command checks for all the allocated "htsp_info_t" structures. These structures store information corresponding to all the endpoints. These structures are allocated only during system startup time. The structures are allocated for all the interfaces present, but the "vtsp_sdb_t" structure is allocated only for the first channel of the BRI port.
Since the endpoints that use the Media Gateway Control Protocol Application (MGCPAPP) as the application layer have to be displayed, the endpoints are displayed even if MGCPAPP is the only application being used by the endpoint. Because the MGCPAPP is shared across both the BRI channels and is port specific, both ports are displayed.
Examples
The following is partial sample output from the show mgcp command when the mdste modem relay package has been enabled:
Router# show mgcp MGCP Admin State ACTIVE, Oper State ACTIVE - Cause Code NONE MGCP call-agent: 10.7.0.200 3460 Initial protocol service is MGCP 0.1 MGCP validate call-agent source-ipaddr DISABLED MGCP block-newcalls DISABLED MGCP send SGCP RSIP: forced/restart/graceful/disconnected DISABLED MGCP quarantine mode discard/step MGCP quarantine of persistent events is ENABLED MGCP dtmf-relay for VoIP disabled for all codec types MGCP dtmf-relay for VoAAL2 disabled for all codec types MGCP voip modem passthrough mode: NSE, codec: g711ulaw, redundancy: DISABLED, MGCP voaal2 modem passthrough disabled MGCP voip nse modem relay: Disabled MGCP voip mdste modem relay: Enabled SPRT rx v14 hold time: 50 (ms), SPRT tx v14 hold count: 16, SPRT tx v14 hold time: 20 (ms), SPRT Retries: 12 SSE redundancy interval: 20 (ms), SSE redundancy packet: 3, SSE t1 timer: 1000 (ms), SSE retries: 3 MGCP TSE payload: 100 MGCP T.38 Named Signalling Event (NSE) response timer: 200 MGCP Network (IP/AAL2) Continuity Test timer: 200 MGCP 'RTP stream loss' timer: 5 MGCP request timeout 500 MGCP maximum exponential request timeout 4000 MGCP gateway port: 2427, MGCP maximum waiting delay 20000 MGCP restart delay 0, MGCP vad DISABLED MGCP rtrcac DISABLED MGCP system resource check DISABLED MGCP xpc-codec: DISABLED, MGCP persistent hookflash: DISABLED MGCP persistent offhook: ENABLED, MGCP persistent onhook: DISABLED MGCP piggyback msg ENABLED, MGCP endpoint offset DISABLED MGCP simple-sdp ENABLED MGCP undotted-notation DISABLED MGCP codec type g711ulaw, MGCP packetization period 20 MGCP JB threshold lwm 30, MGCP JB threshold hwm 150 MGCP LAT threshold lwm 150, MGCP LAT threshold hwm 300 MGCP PL threshold lwm 1000, MGCP PL threshold hwm 10000 MGCP CL threshold lwm 1000, MGCP CL threshold hwm 10000 MGCP playout mode is adaptive 60, 4, 200 in msec MGCP Fax Playout Buffer is 300 in msec MGCP media (RTP) dscp: ef, MGCP signaling dscp: af31 MGCP default package: line-package MGCP supported packages: gm-package dtmf-package mf-package trunk-package line-package hs-package rtp-package script-package ms-package dt-package mo-package mt-package sst-package mdr-package fxr-package pre-package mdste-package srtp-package tone-package MGCP Digit Map matching order: shortest match SGCP Digit Map matching order: always left-to-right MGCP VoAAL2 ignore-lco-codec DISABLED MGCP T.38 Max Fax Rate is DEFAULT MGCP T.38 Fax is ENABLED MGCP T.38 Fax ECM is ENABLED MGCP T.38 Fax NSF Override is DISABLED MGCP T.38 Fax Low Speed Redundancy: 0 MGCP T.38 Fax High Speed Redundancy: 0 MGCP control bind :DISABLED MGCP media bind :DISABLED MGCP Upspeed payload type for G711ulaw: 0, G711alaw: 8 MGCP Dynamic payload type for G.726-16K codec MGCP Dynamic payload type for G.726-24K codec MGCP Dynamic payload type for G.Clear codecThe following sample output displays the status of media source checking and the gateway role:
Router# show mgcp MGCP Admin State ACTIVE, Oper State ACTIVE - Cause Code NONE MGCP call-agent: 10.7.0.201 2497 Initial protocol service is MGCP 1.0 . . . MGCP Dynamic payload type for NTE is 99 MGCP rsip-range is enabled for TGCP only. MGCP Comedia role is PASSIVE MGCP Comedia check media source is ENABLED MGCP Comedia sdp force is DISABLED MGCP Guaranteed scheduler time is DISABLED MGCP DNS stale threshold is 30 seconds . . .The following is partial sample output from the show mgcp command when the mdste package has been disabled:
Router(config)# no mgcp package-capability mdste-package Router(config)# exit Router# show mgcp MGCP voip mdste modem relay: DisabledThe table below describes the significant fields shown in the displays.
Table 19 show mgcp Field Descriptions Field
Description
MGCP Admin State...Oper State
Administrative and operational state of the MGCP daemon. The administrative state controls the starting and the stopping of the application using the mgcp and mgcp block-newcallscommands. The operational state controls the normal MGCP operations.
MGCP call-agent
Address of the call agent specified in the mgcp call-agent or call-agent command and the protocol initiated for this session.
MGCP block-newcalls
State of the mgcp block-newcalls command.
MGCP send SGCP RSIP, disconnected
Setting for the mgcp sgcp restart notify and the mgcp sgcp disconnected notifycommands (enabled or disabled).
MGCP quarantine mode
How the quarantine buffer is to handle Simple Gateway Control Protocol (SGCP) events.
MGCP quarantine of persistent events is
Specifies whether the SGCP persistent events are handled by the quarantine buffer.
MGCP dtmf-relay
Setting for the mgcp dtmf-relay command.
MGCP voip modem passthrough
Settings for mode, codec, and redundancy from the mgcp modem passthrough mode, mgcp modem passthrough codec, and mgcp modem passthrough voip redundancy commands.
MGCP voip mdste modem relay
Settings for the mgcp modem relay voip sprt v14 receive playback, mgcp modem relay voip sprt v14 transmit maximum hold-count, mgcp modem relay voip sprt v14 transmit hold-time, mgcp modem relay voip sprt retries, mgcp modem relay voip sse redundancy, and mgcp modem relay voip sse t1 commands.
SPRT rx v14 hold time
Setting for the mgcp modem relay voip sprt v14 receive playback hold-time time command.
SPRT tx v14 hold count
Setting for the mgcp modem relay voip sprt v14transmit maximum hold-count characters command.
SPRT tx v14 hold time
Setting for the mgcp modem relay voip sprt v14 transmit hold-time timecommand.
SPRT Retries
Setting for the mgcp modem relay voip sprt retries command.
SSE redundancy interval
Setting for the mgcp modem relay voip mode sse redundancy interval time command.
SSE redundancy packet
Setting for the mgcp modem relay voip mode sse redundancy packetcommand.
SSE t1 timer
Setting for the mgcp modem relay voip mode sse redundancy t1 command.
SSE retries
Setting for the mgcp modem relay voip mode sse redundancy retriescommand.
MGCP Comedia role
Location of gateway:
MGCP Comedia check media source
Global media IP and port address detection status (ENABLED or DISABLED).
MGCP Comedia sdp force
Configuration state of forced insertion of the direction attribute in the SDP (ENABLED or DISABLED)
MGCP TSE payload
Setting for the mgcp tse payload command.
MGCP Network (IP/AAL2) Continuity Test timer
Setting for the net-cont-test keyword in the mgcp timer command.
MGCP ‘RTP stream loss’ timer
Setting for the receive-rtcp keyword in the mgcp timer command.
MGCP request timeout
Setting for the mgcp request timeout command.
MGCP maximum exponential request timeout
Setting for the mgcp request timeout max command.
MGCP gateway port
UDP port specification for the gateway.
MGCP maximum waiting delay
Setting for the mgcp max-waiting-delay command.
MGCP restart delay
Setting for the mgcp restart-delay command.
MGCP vad
Setting for the mgcp vadcommand.
MGCP rtrcac
Specifies whether MGCP SA Agent CAC has been enabled with the mgcp rtrcac command.
MGCP system resource check
Specifies whether MGCP SRC CAC has been enabled with the mgcp src-caccommand.
MGCP xpc-codec
Specifies whether the mgcp sdp xpc-codeccommand has been configured to generate the X-pc codec field for Session Description Protocol (SDP) codec negotiation in Network-Based Call Signaling (NCS) and Trunking Gateway Control Protocol (TGCP).
MGCP persistent hookflash
Specifies whether the mgcp persistent hookflash command has been configured to send persistent hookflash events to the call agent.
MGCP persistent offhook
Specifies whether the mgcp persistent offhook command has been configured to send persistent off-hook events to the call agent.
MGCP persistent onhook
Specifies whether the mgcp persistent onhookcommand has been configured to send persistent on-hook events to the call agent.
MGCP piggyback msg
Specifies whether the mgcp piggyback message command has been configured to enable piggyback messaging.
MGCP endpoint offset
Specifies whether the mgcp endpoint offset command has been configured to enable incrementing of the local portion of an endpoint name for NCS. The local portion contains the analog or digital voice port identifier.
MGCP simple-sdp
Specifies whether the mgcp sdp simplecommand has been configured to enable simple mode SDP operation.
MGCP undotted-notation
Specifies whether the mgcp sdp notation undotted command has been configured to enable undotted SDP notation for the codec string.
MGCP codec type
Setting for the mgcp codeccommand.
MGCP packetization period
The packetization periodparameter setting for the mgcp codeccommand.
MGCP JB threshold lwm
Jitter-buffer minimum-threshold parameter setting for the mgcp quality-threshold command.
MGCP JB threshold hwm
Jitter-buffer maximum-threshold parameter setting for the mgcp quality-threshold command.
MGCP LAT threshold lwm
Latency minimum-threshold parameter setting for the mgcp quality-threshold command.
MGCP LAT threshold hwm
Latency maximum-threshold parameter setting for the mgcp quality-threshold command.
MGCP PL threshold lwm
Packet-loss minimum-threshold parameter setting for the mgcp quality-thresholdcommand.
MGCP PL threshold hwm
Packet-loss maximum-threshold parameter setting for the mgcp quality-threshold command.
MGCP CL threshold lwm
Cell-loss minimum-threshold parameter setting for the mgcp quality-thresholdcommand.
MGCP CL threshold hwm
Cell-loss maximum-threshold parameter setting for the mgcp quality-thresholdcommand.
MGCP playout mode is
Jitter-buffer packet type and size.
MGCP default package
Package configured as the default package with the mgcp default-packagecommand.
MGCP supported packages
Packages configured with the mgcp package-capability command to be supported on this gateway in this session. The Line Control Signaling Package (lcs-package) display is new in Cisco IOS Release 12.3(8)T.
MGCP voaal2 modem passthrough
Settings for mode, codec, and redundancy from the mgcp modem passthrough modeand mgcp modem passthrough codec commands.
MGCP T.38 Fax
Settings for the mgcp fax t.38 command. The following values are displayed:
- MGCP T.38 fax: ENABLED or DISABLED.
- Error correction mode (ECM): ENABLED or DISABLED.
- Nonstandard facilities (NSF) override: ENABLED or DISABLED. If enabled, the override code is displayed.
- MGCP T.38 fax low-speed redundancy: the factor set on the gateway for redundancy.
- MGCP T.38 fax high-speed redundancy: the factor set on the gateway for redundancy.
Related Commands
Command
Description
ccm-manager config
Supplies the local MGCP voice gateway with the IP address or logical name of the TFTP server from which to download XML configuration files and enable the download of the configuration.
debug ccm-manager
Displays debugging information about the Cisco CallManager.
debug mgcp
Enables debug traces for MGCP errors, events, media, packets, and parser.
isdn bind-l3 (interface BRI)
Configures the BRI to support MGCP and to bind ISDN Layer 3 with Cisco CallManager backhaul.
mgcp
Allocates resources for the MGCP and starts the daemon.
mgcp behavior comedia-check-media-src
Enables IP address and port detection from the first RTP packet received for the entire MGCP gateway.
mgcp behavior comedia-role
Indicates the location of the MGCP gateway.
mgcp behavior comedia-sdp-force
Forces the SDP to place the direction attribute in the SDP using the command as a reference.
mgcp package-capability mdste-package
Specifies the MGCP package capability type for a media gateway.
security password-group
Defines the passwords used by gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.
show ccm-manager
Displays a list of Cisco CallManager servers and their current statuses, and availability.
show ccm-manager fallback-mgcp
Displays the status of the MGCP gateway fallback feature.
show mgcp connection
Displays information for active MGCP-controlled connections.
show mgcp endpoint
Displays information for MGCP-controlled endpoints.
show mgcp nas
Displays MGCP NAS information for data ports.
show mgcp profile
Displays values for MGCP profile-related parameters.
show mgcp statistics
Displays MGCP statistics regarding received and transmitted network messages.
show mgcp connection
To display information for active connections that are controlled by the Media Gateway Control Protocol (MGCP), use the show mgcp connection command inprivileged EXEC mode.
Command History
Release
Modification
12.1(1)T
The show mgcp command was introduced on the Cisco AS5300.
12.1(3)T
The show mgcpcommand output was updated to display additional gateway and platform information.
12.1(5)XM
The show mgcpcommand output was updated to display additional gateway and platform information.
12.2(2)T
The show mgcp command was implemented on the Cisco 7200 series and was integrated into Cisco IOS Release 12.2(2)T.
12.2(2)XA
The profile keyword was added.
12.2(4)T
This command was integrated into Cisco IOS Release 12.2(4)T.
12.2(2)XB
Output for the show mgcpcommand was enhanced to display the status of MGCP System Resource Check (SRC) Call Admission Control (CAC) and Service Assurance Agent (SA Agent) CAC. (Refer to the Cisco IOS Release 12.2(2) XB online document MGCP VoIP Call Admission Control .)
The nas dump slot port channel and nas info keywords and arguments were added. Because the number of keywords increased, the command page for the show mgcp command was separated into the following command pages:
12.2(8)T
This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.
12.2(11)T
Support was added for the Cisco AS5300, Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850.
12.3(11)T
Command output was enhanced to display the encryption suite used on the Secure Real-Time Transport Protocol (SRTP) connection.
12.4(2)T
Command output was enhanced to display the current media state.
12.4(11)T
Command output was enhanced to display the detected NAT address and port.
Examples
The following is sample output from the show mgcp connectioncommand displaying a secure call for which the media state is modem relay mode:
Router# show mgcp connection Endpoint Call_ID(C) Conn_ID(I) (P)ort (M)ode (S)tate (CO)dec (E)vent[SIFL] (R)esult[EA] (ME)dia 1. S2/DS1-2/1 C=A000000001000010000000F5,4,3 I=0x2 P=17098,2662 M=3 S=4,4 CO=1 E=3,0,0,3 R=0,0 ME=2The following is sample output from this command showing the detected NAT address and port. The (P)ort output shows the local and advertised ports prior to detection. The (COM)Addr/Port output shows the detected media address and port (10.7.1.21:1500):
Router# show mgcp connection Endpoint Call_ID(C) Conn_ID (I) (P)ort (M)ode(S)tate(CO)dec (E)vent[SIFL] (R)esult[EA] (COM)Addr/Port S7/DS1-4/1 C=201597,768784,768785 I=0x5DD85 P=18258,19062 M=3 S=4,4 CO=2 E=2,0,0,2 R=0,0,0,2 COM=10.7.1.21:15000The following is sample output from this command for encrypted connections:
Router# show mgcp connection Endpoint Call_ID(C) Conn_ID(I) (P)ort (M)ode (S)tate (CO)dec (E)vent[SIFL] (R)esult[EA] Encryption(K) 1. S1/DS1-0/1 C=2,1,2 I=0x2 P=18204,0 M=2 S=4,4 CO=1 E=0,0,0,0 R=0,0 K=1The following is sample output from this command for VoIP connections:
Router# show mgcp connection Endpoint Call_ID(C) Conn_ID(I) (P)ort (M)ode (S)tate (C)odec (E)vent[SIFL] (R)esult[EA] 1. S0/DS1-0/1 C=103,23,24 I=0x8 P=16586,16634 M=3 S=4,4 C=5 E=2,0,0,2 R=0,0 2. S0/DS1-0/2 C=103,25,26 I=0x9 P=16634,16586 M=3 S=4,4 C=5 E=0,0,0,0 R=0,0 3. S0/DS1-0/3 C=101,15,16 I=0x4 P=16506,16544 M=3 S=4,4 C=5 E=2,0,0,2 R=0,0 4. S0/DS1-0/4 C=101,17,18 I=0x5 P=16544,16506 M=3 S=4,4 C=5 E=0,0,0,0 R=0,0 5. S0/DS1-0/5 C=102,19,20 I=0,6 P=16572,16600 M=3 S=4,4 C=5 E=2,0,0,2 R=0,0 6. S0/DS1-0/6 C=102,21,22 I=0x7 P=16600,16572 M=3 S=4,4 C=5 E=0,0,0,0 R=0,0 Total number of active calls 6The following is sample output from this command for Voice over ATM Adaptation Layer 2 (VoAAL2) connections:
Router# show mgcp connection Endpoint Call_ID(C) Conn_ID(I)(V)cci/cid (M)ode (S)tate (C)odec (E)vent[SIFL] (R)esult[EA] 1.aaln/S1/1 C=1,11,12 I=0x2 V=2/10 M=3 S=4,4 C=1 E=3,0,0,3 R=0,0 Total number of active calls 1The table below describes the significant fields shown in the displays.
Table 20 show mgcpconnection Field Descriptions Field
Description
Endpoint
Endpoint for each call shown in the digital endpoint naming convention of slot number (S0) and digital line (DS1-0) number (1).
Call_ID(C)
MGCP call ID sent by the call agent, the internal Call Control Application Programming Interface (CCAPI) call ID for this endpoint, and the CCAPI call ID of the peer call legs.
(CCAPI is an API that provides call control facilities to applications.)
(COM)Addr/Port
Detected media address and port.
Conn_ID(I)
Connection ID generated by the gateway and sent in the ACK message.
(P)ort
Ports used for this connection. The first port is the local User Datagram Protocol (UDP) port. The second port is the remote UDP port.
(V)cci/cid
Virtual channel connection identifier (VCCI) and channel identifier (CID) used for the VoAAL2 call.
(Me)dia
Media state, where:
(M)ode
Call mode, where:
- 0--Invalid value for mode.
- 1--Gateway should only send packets.
- 2--Gateway should only receive packets.
- 3--Gateway should send and receive packets.
- 4--Gateway should neither send nor receive packets.
- 5--Gateway should place the circuit in loopback mode.
- 6--Gateway should place the circuit in test mode.
- 7--Gateway should use the circuit for network access for data.
- 8--Gateway should place the connection in network loopback mode.
- 9--Gateway should place the connection in network continuity test mode.
- 10--Gateway should place the connection in conference mode.
All other values are used for internal debugging.
(S)tate
Call state. The values are used for internal debugging purposes.
(Co)dec
Codec identifier. The values are used for internal debugging purposes.
(E)vent [SIFL]
Used for internal debugging.
(R)esult [EA]
Used for internal debugging.
Encryption(K)
Encryption suite, where:
Related Commands
Command
Description
debug mgcp
Enables debug traces for MGCP errors, events, media, packets, and parser.
mgcp
Allocates resources for the MGCP and starts the daemon.
mgcp behavior comedia-check-media-src
Enables ip address and port detection from the first rtp packet received for the entire MGCP gateway.
mgcp behavior comedia-role
Indicates the location of the MGCP gateway.
mgcp behavior comedia-sdp-force
Forces the SDP to place the direction attribute in the SDP using the command as a reference.
security password-group
Defines the passwords used by gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.
show mgcp
Displays values for MGCP parameters.
show mgcp endpoints
Displays information for MGCP-controlled endpoints.
show mgcp nas
Displays MGCP NAS information for data ports.
show mgcp profile
Displays values for MGCP profile-related parameters.
show mgcp statistics
Displays MGCP statistics regarding received and transmitted network messages.
show mgcp endpoint
To display information for endpoints controlled by Media Gateway Control Protocol (MGCP), use the show mgcp endpoint command inprivileged EXEC mode.
Command History
Release
Modification
12.1(1)T
The show mgcp command was introduced on the Cisco AS5300.
12.1(3)T
The show mgcpcommand output was updated to display additional gateway and platform information.
12.1(5)XM
The show mgcp command output was updated to display additional gateway and platform information.
12.2(2)T
The show mgcp command was implemented on the Cisco 7200 series and this command was integrated into Cisco IOS Release 12.2(2)T.
12.2(2)XA
The profile keyword was added to the show mgcp command.
12.2(4)T
This command was integrated into Cisco IOS Release 12.2(4)T.
12.2(2)XB
The output for the show mgcp command was enhanced to display the status of MGCP System Resource Check (SRC) Call Admission Control (CAC) and Service Assurance Agent (SA Agent) CAC. (Refer to the Cisco IOS Release 12.2(2) XB online document MGCP VoIP Call Admission Control. )
In addition, the nas dump slot port channel and nas info keywords and arguments were added to the show mgcp command. Because the number of keywords increased, the command-reference page for the show mgcp command was separated into the following command-reference pages:
12.2(8)T
This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.
12.2(11)T
This command is supported on the Cisco AS5300, Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850 in this release.
Examples
The following is sample output from this command:
Router# show mgcp endpoint ENDPOINT-NAME V-PORT SIG-TYPE ADMIN ds1-0/1@nytnk116 0:1 fxs-gs up ds1-0/2@nytnk116 0:1 fxs-gs up ds1-0/3@nytnk116 0:1 fxs-gs up ds1-0/4@nytnk116 0:1 fxs-gs up ds1-0/5@nytnk116 0:1 fxs-gs up ds1-0/6@nytnk116 0:1 fxs-gs up ds1-0/7@nytnk116 0:1 fxs-gs up ds1-0/8@nytnk116 0:1 fxs-gs up ds1-0/9@nytnk116 0:1 fxs-gs up ds1-0/10@nytnk116 0:1 fxs-gs up ds1-0/11@nytnk116 0:1 fxs-gs up ds1-0/12@nytnk116 0:1 fxs-gs up ds1-0/13@nytnk116 0:1 fxs-gs up ds1-0/14@nytnk116 0:1 fxs-gs up ds1-0/15@nytnk116 0:1 fxs-gs up ds1-0/16@nytnk116 0:1 fxs-gs up ds1-0/17@nytnk116 0:1 fxs-gs up ds1-0/18@nytnk116 0:1 fxs-gs up ds1-0/19@nytnk116 0:1 fxs-gs up ds1-0/20@nytnk116 0:1 fxs-gs up ds1-0/21@nytnk116 0:1 fxs-gs up ds1-0/22@nytnk116 0:1 fxs-gs up ds1-0/23@nytnk116 0:1 fxs-gs up ds1-0/24@nytnk116 0:1 fxs-gs up Interface T1 1 ENDPOINT-NAME V-PORT SIG-TYPE ADMIN ds1-1/1@nytnk116 1:1 e&m-imd up ds1-1/2@nytnk116 1:1 e&m-imd upThe table below describes significant fields shown in this output.
Table 21 show mgcp endpoint Field Descriptions Field
Description
ENDPOINT-NAME
Name used by the call agent to identify a specific mgcp endpoint on a given gateway.
V-PORT
Voice port
SIG-TYPE
Signaling type for a given endpoint (for example, NONE for SS7 ISDN User Part (ISUP) and FXS-GS for Foreign Exchange Station (FXS) Ground Start).
ADMIN
Administrative status--Up or Down. (This field is populated only on residential gateway (RGW) platforms.
Related Commands
Command
Description
debug mgcp
Enables debug traces for MGCP errors, events, media, packets, and parser.
mgcp
Allocates resources for the MGCP and starts the daemon.
security password-group
Defines the passwords used by gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.
show mgcp
Displays information for MGCP parameters.
show mgcp connection
Displays information for active MGCP-controlled connections.
show mgcp nas
Displays MGCP NAS information for data ports.
show mgcp profile
Displays values for MGCP profile-related parameters.
show mgcp statistics
Displays MGCP statistics regarding received and transmitted network messages.
show mgcp nas
To display Media Gateway Control Protocol (MGCP) network access server (NAS) information for data ports, use the show mgcp nas command in privileged EXEC mode.
Syntax Description
Command History
Release
Modification
12.1(1)T
The show mgcp command was introduced on the Cisco AS5300.
12.1(3)T
The show mgcp command output was updated to display additional gateway and platform information.
12.1(5)XM
The show mgcp command output was updated to display additional gateway and platform information.
12.2(2)T
The show mgcp command was implemented on the Cisco 7200 series and this command was integrated into Cisco IOS Release 12.2(2)T.
12.2(2)XA
The profile keyword was added to the show mgcp command.
12.2(4)T
This command was integrated into Cisco IOS Release 12.2(4)T.
12.2(2)XB
The output for the show mgcp command was enhanced to display the status of MGCP System Resource Check (SRC) Call Admission Control (CAC) and Service Assurance Agent (SA Agent) CAC. (Refer to the Cisco IOS Release 12.2(2) XB online document MGCP VoIP Call Admission Control. )
In addition, the nas dump slot port channel and nas info keywords and arguments were added to the show mgcp command. Because the number of keywords increased, the command-reference page for the show mgcp command was separated into the following command-reference pages:
12.2(8)T
This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.
12.2(11)T
This command is supported on the Cisco AS5300, Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850 in this release.
12.3(7)YB
The valid values for the bearer cap field of the show mgcp nas dump command output were changed to include LAPB, V.120, and sync data. The Signaling field was added to the show mgcp nas dump command output. See the table below.
12.4(6)T
This command was integrated into Cisco IOS Release 12.4(6)T
Examples
The following is sample output from this command for an autodetected V.120 call:
Router# show mgcp nas dump 1 7 24 Slot 1 state=Up Port 7 state=Up State In Use PortCb=0x6577949C ss_id=0x0 handle=0x65C88228 Bearer Cap=V.120 call_id=1 conn_id=6577B8EC Sig Type=Autodetect Events req- nas/crq- req id=7 :nas/of- req id=7 : Endpt name=S1/DS1-7/24 call_id = 1, conn_id=0x6577B8EC cgn=1000 cdn=5555 Rx packets=610 Rx bytes=73242 Tx packets 716 Tx bytes 72987The table below describes the significant fields shown in the display.
Table 22 show mgcp nas dump Field Descriptions Field
Description
Slot state
Status of specified slot.
Port state
Status of specified port.
State
Call status for the specified channel.
bearer cap
Bearer capability. Values are:
V.110, V.120, modem, or digital values are displayed when autodetection is not enabled and the signaling type is set to External. LAPB, V.120, and digital values are displayed if autodetection is enabled, and the signaling type is set to Autodetect.
call_id
Call identification for the currently active call, if any.
conn_id
Connection identification for the currently active call, if any.
Signaling
Call type signaling. Values are:
Events req
List of NAS events requested, if any, and their request IDs. The request ID identifies the MGCP message from the call agent that requested the events.
Endpt name
MGCP endpoint name.
The following sample output from this command shows the state, either Idle or In Use, for each channel:
Router# show mgcp nas info Number of ports configured=1 Slot 1 configured slot state=Up Port 7 state=Up =====Port 7 Channel States===== 0 Idle 1 Idle 2 Idle 3 Idle 4 Idle 5 Idle 6 Idle 7 Idle 8 Idle 9 Idle 10 Idle 11 Idle 12 Idle 13 Idle 14 Idle 15 Idle 16 Idle 17 Idle 18 Idle 19 Idle 20 Idle 21 Idle 22 Idle 23 In Use =======================================Related Commands
Command
Description
debug mgcp
Enables debug traces for MGCP errors, events, media, packets, and parser.
mgcp
Allocates resources for the MGCP and starts the daemon.
security password-group
Defines the passwords used by gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.
show mgcp
Displays information for MGCP parameters.
show mgcp connection
Displays information for active MGCP-controlled connections.
show mgcp endpoint
Displays information for MGCP-controlled endpoints.
show mgcp profile
Displays values for MGCP profile-related parameters.
show mgcp statistics
Displays MGCP statistics regarding received and transmitted network messages.
show mgcp profile
To display information for Media Gateway Control Protocol (MGCP) profiles, use the show mgcp profile command in privileged EXEC mode.
Command Default
If the optional profile-name argument is not used, all configured profiles are displayed.
Command History
Release
Modification
12.1(1)T
The show mgcp command was introduced on the Cisco AS5300.
12.1(3)T
The show mgcp command output was updated to display additional gateway and platform information.
12.1(5)XM
The show mgcp command output was updated to display additional gateway and platform information.
12.2(2)T
The show mgcp command was implemented on the Cisco 7200 series and this command was integrated into Cisco IOS Release 12.2(2)T.
12.2(2)XA
The profile keyword was added to the show mgcp command.
12.2(4)T
This command was integrated into Cisco IOS Release 12.2(4)T.
12.2(2)XB
Output for the show mgcpcommand was enhanced to display the status of MGCP System Resource Check (SRC) Call Admission Control (CAC) and Service Assurance Agent (SA Agent) CAC. (See the Cisco IOS Release 12.2(2)XB online document MGCP VoIP Call Admission Control. )
In addition, the nas dump slot port channel and nas info keywords and arguments were added to the show mgcp command. Because the number of keywords increased, the command-reference page for the show mgcp command was separated into the following command-reference pages:
12.2(8)T
This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.
12.2(11)T
This command is supported on the Cisco AS5300, Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850 in this release.
12.4(4)T
Output was added to show the order in which ANI and DNIS digits are sent to the call agent.
Examples
The following is sample output for this command for the default profile:
Router# show mgcp profile default MGCP Profile default Description: None Call-agent: none Initial protocol service is unknown Tsmax timeout is 20 sec, Tdinit timeout is 15 sec Tdmin timeout is 15 sec, Tdmax timeout is 600 sec Tcrit timeout is 4 sec, Tpar timeout is 16 sec Thist timeout is 30 sec, MWI timeout is 16 sec Ringback tone timeout is 180 sec, Ringback tone on connection timeout is 180 sec Network congestion tone timeout is 180 sec, Busy tone timeout is 30 sec Dial tone timeout is 16 sec, Stutter dial tone timeout is 16 sec Ringing tone timeout is 180 sec, Distinctive ringing tone timeout is 180 sec Continuity1 tone timeout is 3 sec, Continuity2 tone timeout is 3 sec Reorder tone timeout is 30 sec, Persistent package is ms-package Max1 DNS lookup: ENABLED, Max1 retries is 5 Max2 DNS lookup: ENABLED, Max2 retries is 7 Source Interface: NONE T3 endpoint naming convention is T1 CAS Notification Digit order is DNIS-ANIThe following is sample output for this command for a profile named "example":
Router# show mgcp profile example MGCP Profile example Description:None Call-agent:10.9.57.6 5003 Initial protocol service is MGCP 1.0 Tsmax timeout is 20, Tdinit timeout is 15 Tdmin timeout is 15, Tdmax timeout is 600 Tcrit timeout is 4, Tpar timeout is 16 Thist timeout is 30, MWI timeout is 16 Ringback tone timeout is 180, Ringback tone on connection timeout is 180 Network congestion tone timeout is 180, Busy tone timeout is 30 Dial tone timeout is 16, Stutter dial tone timeout is 16 Ringing tone timeout is 180, Distinctive ringing tone timeout is 180 Continuity1 tone timeout is 3, Continuity2 tone timeout is 3 Reorder tone timeout is 30, Persistent package is ms-package Max1 DNS lookup:ENABLED, Max1 retries is 4 Max2 DNS lookup:ENABLED, Max2 retries is 6 Voice port:1The table below describes significant fields shown in these outputs.
Table 23 show mgcp profile Field Descriptions Field
Description
MGCP Profile
The name configured for this profile with the mgcp profile command.
Description
Description configured for this profile with the description MGCP profilecommand.
Call-agent
Domain name server (DNS) or IP address of the call agent, as configured for this profile with the call-agentcommand.
Initial protocol service
Protocol service to be used, as configured for this profile with the call-agent command.
Tsmax timeout
Maximum timeout value for removing messages from the retransmission queue, as configured for this profile by the timeout tsmax command.
Tdinit timeout
Initial waiting delay, as configured for this profile by the timeout tdinit command.
Tdmin timeout
Minimum timeout value for the disconnected procedure, as configured for this profile by the timeout tdmin command.
Tdmax timeout
Maximum timeout value for the disconnected procedure, as configured for this profile by the timeout tdmax command.
Tcrit timeout
Critical timeout value for the interdigit timer used in digit matching, as configured for this profile by the timeout tcrit command.
Tpar timeout
Partial timeout value for the interdigit timer used in digit matching, as configured for this profile by the timeout tpar command.
Thist timeout
Packet storage timeout value, as configured for this profile by the timeout thist command.
MWI timeout
Timeout value for message-waiting-indicator tone, as configured for this profile by the timeout tone mwi command.
Ringback tone timeout
Timeout value for ringback tone, as configured for this profile by the timeout tone ringback command.
Ringback tone on connection timeout
Timeout value for ringback tone on connection, as configured for this profile by the timeout tone ringback connection command.
Network congestion tone timeout
Timeout value for the network congestion tone, as configured for this profile by the timeout tone network congestion command.
Busy tone timeout
Timeout value for the busy tone, as configured for this profile by the timeout tone busy command.
Dial tone timeout
Timeout value for the dial tone, as configured for this profile by the timeout tone dial command.
Stutter dial tone timeout
Timeout value for the stutter dial tone, as configured for this profile by the timeout tone dial stutter command.
Ringing tone timeout
Timeout value for the ringing tone, as configured for this profile by the timeout tone ringing command.
Distinctive ringing tone timeout
Timeout value for the distinctive ringing tone, as configured for this profile by the timeout tone ringing distinctive command.
Continuity1 tone timeout
Timeout value for the continuity1 tone, as configured for this profile by the timeout tone cot1 command.
Continuity2 tone timeout
Timeout value for the continuity2 tone, as configured for this profile by the timeout tone cot2 command.
Reorder tone timeout
Timeout value for the reorder tone, as configured for this profile by the timeout tone reorder command.
Persistent package
Name of package configured as persistent for this profile by the package persistent command.
Max1 lookup
Domain name server (DNS) lookup for the call agent after the suspicion threshold is reached, as configured for this profile by the max1 lookup command.
Max1 retries
Number of retries to reach the call agent before a new DNS lookup is performed, as configured for this profile by the max1 retries command.
Max2 lookup
DNS lookup for the call agent after the disconnected threshold is reached, as configured by the max2 lookup command.
Max2 retries
Maximum number of retries to reach the call agent before a new DNS lookup is performed, as configured by the max2 retries command.
CAS Notification Digit order
Order in which ANI and DNIS digits are sent in the notify message as configured with the notify command.
Related Commands
Command
Description
debug mgcp
Enables debug traces for MGCP errors, events, media, packets, and parser.
mgcp
Allocates resources for the MGCP and starts the daemon.
security password-group
Defines the passwords used by the gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.
show mgcp
Displays information for MGCP parameters.
show mgcp connection
Displays information for active MGCP-controlled connections.
show mgcp endpoint
Displays information for MGCP-controlled endpoints.
show mgcp nas
Displays MGCP NAS information for data ports.
show mgcp statistics
Displays MGCP statistics regarding received and transmitted network messages.
show mgcp srtp
To display information for active Secure Real-Time Transport Protocol (SRTP) connections that are controlled by Media Gateway Control Protocol (MGCP), use the show mgcp srtp command inprivileged EXEC mode.
Usage Guidelines
This command provides information about secure calls created by the MGCP application. To specify connection endpoints for display, use the show mgcp srtp detail endpoint command. To display valid values for the endpoint argument, that is, the endpoint port numbers, use the show mgcp connection command. Use the show mgcp srtp detail command to display a hashed version of the master key and salts (encryption mechanisms) used on each connection. This display allows you to validate keys and salts for each endpoint of a call without revealing the actual master key and salt.
Examples
The following is sample output from this command for encrypted connections:
Router# show mgcp srtp summary MGCP SRTP Connection Summary Endpoint Conn Id Crypto Suite aaln/S3/SU0/0 8 AES_CM_128_HMAC_SHA1_32 aaln/S3/SU0/1 9 AES_CM_128_HMAC_SHA1_32 S3/DS1-0/1 6 AES_CM_128_HMAC_SHA1_32 S3/DS1-0/2 7 AES_CM_128_HMAC_SHA1_32 4 SRTP connections activeRouter# show mgcp srtp detail MGCP SRTP Connection Detail for Endpoint *Definitions: CS=Crypto Suite, KS=HASHED Master Key/Salt, SSRC=Syncronization Source, ROC=Rollover Counter, KDR=Key Derivation Rate, SEQ=Sequence Number, FEC=FEC Order, MLT=Master Key Lifetime, MKI=Master Key Index:MKI Size Endpoint aaln/S3/SU0/0 Call ID 2 Conn ID 8 Tx:CS=AES_CM_128_HMAC_SHA1_32 KS=3NaOYXS9dLoYDaBHpzRejREfhf0= SSRC=Random ROC=0 KDR=1 SEQ=Random FEC=FEC->SRTP MLT=0x80000000 MKI=0:0 Rx:CS=AES_CM_128_HMAC_SHA1_32 KS=llYCQoqxtxtdf7ECe+x+DK+G9v4= SSRC=Random ROC=0 KDR=1 SEQ=Random FEC=FEC->SRTP MLT=0x80000000 MKI=0:0 Endpoint aaln/S3/SU0/1 Call ID 101 Conn ID 9 Tx:CS=AES_CM_128_HMAC_SHA1_32 KS=llYCQoqxtxtdf7ECe+x+DK+G9v4= SSRC=Random ROC=0 KDR=1 SEQ=Random FEC=FEC->SRTP MLT=0x80000000 MKI=0:0 Rx:Not Configured Endpoint S3/DS1-0/1 Call ID 1 Conn ID 6 Tx:CS=AES_CM_128_HMAC_SHA1_32 KS=3NaOYXS9dLoYDaBHpzRejREfhf0= SSRC=Random ROC=0 KDR=1 SEQ=Random FEC=FEC->SRTP MLT=0x80000000 MKI=0:0 Rx:CS=AES_CM_128_HMAC_SHA1_32 KS=llYCQoqxtxtdf7ECe+x+DK+G9v4= SSRC=Random ROC=0 KDR=1 SEQ=Random FEC=FEC->SRTP MLT=0x80000000 MKI=0:0 Endpoint S3/DS1-0/2 Call ID 100 Conn ID 7 Tx:CS=AES_CM_128_HMAC_SHA1_32 KS=llYCQoqxtxtdf7ECe+x+DK+G9v4= SSRC=Random ROC=0 KDR=1 SEQ=Random FEC=FEC->SRTP MLT=0x80000000 MKI=0:0 Rx:Not Configured 4 SRTP connections displayed Router# show mgcp srtp detail S3/DS1-0/ * MGCP SRTP Connection Detail for Endpoint S3/DS1-0/* Definitions: CS=Crypto Suite, KS=HASHED Master Key/Salt, SSRC=Syncronization Source, ROC=Rollover Counter, KDR=Key Derivation Rate, SEQ=Sequence Number, FEC=FEC Order, MLT=Master Key Lifetime, MKI=Master Key Index:MKI Size Endpoint S3/DS1-0/1 Call ID 1 Conn ID 6 Tx:CS=AES_CM_128_HMAC_SHA1_32 KS=3NaOYXS9dLoYDaBHpzRejREfhf0= SSRC=Random ROC=0 KDR=1 SEQ=Random FEC=FEC->SRTP MLT=0x80000000 MKI=0:0 Rx:CS=AES_CM_128_HMAC_SHA1_32 KS=llYCQoqxtxtdf7ECe+x+DK+G9v4= SSRC=Random ROC=0 KDR=1 SEQ=Random FEC=FEC->SRTP MLT=0x80000000 MKI=0:0 Endpoint S3/DS1-0/2 Call ID 100 Conn ID 7 Tx:CS=AES_CM_128_HMAC_SHA1_32 KS=llYCQoqxtxtdf7ECe+x+DK+G9v4= SSRC=Random ROC=0 KDR=1 SEQ=Random FEC=FEC->SRTP MLT=0x80000000 MKI=0:0 Rx:Not Configured 2 SRTP connections displayedThe table below describes the significant fields shown in the display.
Table 24 show mgcpsrtp Field Descriptions Field
Description
Endpoint
Endpoint for each call, shown in the digital endpoint naming convention of slot number (S0) and digital line (DS1-0) number (1).
Call ID
MGCP call ID sent by the call agent.
Conn ID
Connection ID generated by the gateway and sent in the ACK message.
Crypto Suite
Identifies the cryptographic suite used on the connection.
Related Commands
Command
Description
debug mgcp
Enables debug traces for MGCP errors, events, media, packets, and parser.
mgcp
Allocates resources for the MGCP and starts the daemon.
security password-group
Defines the passwords used by gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.
show mgcp
Displays values for MGCP parameters.
show mgcp connection
Displays information for active MGCP-controlled connections.
show mgcp endpoint
Displays information for MGCP-controlled endpoints.
show mgcp nas
Displays MGCP NAS information for data ports.
show mgcp profile
Displays values for MGCP profile-related parameters.
show mgcp statistics
To display Media Gateway Control Protocol (MGCP) statistics regarding received and transmitted network messages, use the show mgcp statisticscommand in privileged EXEC mode.
Command History
Release
Modification
12.1(1)T
The show mgcp command was introduced on the Cisco AS5300.
12.1(3)T
The show mgcp command output was updated to display additional gateway and platform information.
12.1(5)XM
The show mgcp command output was updated to display additional gateway and platform information.
12.2(2)T
The show mgcp command was implemented on the Cisco 7200 series and this command was integrated into Cisco IOS Release 12.2(2)T.
12.2(2)XA
The profile keyword was added to the show mgcp command.
12.2(4)T
This command was integrated into Cisco IOS Release 12.2(4)T.
12.2(2)XB
Output for the show mgcp command was enhanced to display the status of MGCP system resource check (SRC) call admission control (CAC) and Service assurance agent (SA Agent) CAC. (Refer to the Cisco IOS Release 12.2(2)XB online document MGCP VoIP Call Admission Control. )
The nas dump slot port channel and nas info keywords and arguments were added to the show mgcp command. To simplify the command reference, the command page for the show mgcp command was separated into the following command pages:
12.2(8)T
This command was integrated into Cisco IOS Release 12.2(8)T. Support for the Cisco AS5300, Cisco AS5350, Cisco AS5400, and Cisco AS5850 is not included in this release.
12.2(11)T
This command is supported on the Cisco AS5300, Cisco AS5350, Cisco AS5400, Cisco AS5800, and Cisco AS5850 in this release.
12.3(11)T
Output was enhanced to display dropped packets from unconfigured call agents if call-agent validation is enabled.
Examples
The following is sample output from this command for VoIP and VoAAL2 statistics:
Router# show mgcp statistics UDP pkts rx 8, tx 9 Unrecognized rx pkts 0, MGCP message parsing errors 0 Duplicate MGCP ack tx 0, Invalid versions count 0 Rx packets from unknown Call Agent 0 CreateConn rx 4, successful 0, failed 0 DeleteConn rx 2, successful 2, failed 0 ModifyConn rx 4, successful 4, failed 0 DeleteConn tx 0, successful 0, failed 0 NotifyRequest rx 0, successful 4, failed 0 AuditConnection rx 0, successful 0, failed 0 AuditEndpoint rx 0, successful 0, failed 0 RestartInProgress tx 1, successful 1, failed 0 Notify tx 0, successful 0, failed 0 ACK tx 8, NACK tx 0 ACK rx 0, NACK rx 0 IP address based Call Agents statistics: IP address 10.24.167.3, Total msg rx 8, successful 8, failed 0The following is an example of the MGCP VoIP SRC CAC portion of this command output for a gateway configured with MGCP VoIP SRC CAC:
Router# show mgcp statistics MGCP System Resource Check Statistics: ------------------------------------- Total CreateConn checked by SRC :0 CreateConn accepted by SRC:0 CreateConn rejected by SRC:0 Total ModifyConn checked by SRC :0 ModifyConn accepted by SRC:0 ModifyConn rejected by SRC:0 Reason Num. of requests rejected ------ ------------------------- cpu-5sec: 0 cpu-avg: 0 total-mem: 0 io-mem: 0 proc-mem: 0 total-calls: 0The table below describes significant fields shown in this output.
Table 25 show mgcp statistics Field Descriptions Field
Description
UDP pkts rx, tx
Number of User Datagram Protocol (UDP) packets transmitted and received from the call agent by the gateway MGCP application.
Unrecognized rx pkts
Number of unrecognized UDP packets received by the MGCP application.
MGCP message parsing errors
Number of MGCP messages received with parsing errors.
Duplicate MGCP ack tx
Number of duplicate MGCP acknowledgment messages transmitted to the call agents.
Invalid versions count
Number of MGCP messages received with invalid MGCP protocol versions.
Rx packets from unknown Call Agent
Number of dropped packets from unconfigured call agents.
CreateConn rx
Number of Create Connection (CRCX) messages received by the gateway, the number that were successful, and the number that failed.
DeleteConn rx
Number of Delete Connection (DLCX) messages received by the gateway, the number that were successful, and the number that failed.
DeleteConn tx
Number of DLCX messages sent from the gateway to the call agent (CA).
ModifyConn rx
Number of Modify Connection (MDCX) messages received by the gateway, the number that were successful, and the number that failed.
NotifyRequest rx
Number of Notify Request (RQNT) messages received by the gateway, the number that were successful, and the number that failed.
AuditConnection rx
Number of Audit Connection (AUCX) messages received by the gateway, the number that were successful, and the number that failed.
AuditEndpoint rx
Number of Audit Endpoint (AUEP) messages received by the gateway, the number that were successful, and the number that failed.
RestartInProgress tx
Number of Restart in Progress (RSIP) messages sent by the gateway, the number that were successful, and the number that failed.
Notify tx
Number of Notify (NTFY) messages sent by the gateway, the number that were successful, and the number that failed.
ACK tx, NACK tx
Number of Acknowledgment and Negative Acknowledgment messages sent by the gateway.
ACK rx, NACK rx
Number of Acknowledgment and Negative Acknowledgment messages received by the gateway.
IP address based Call Agents statistics: IP address, Total msg rx
IP address of the call agent, the total number of MGCP messages received from that call agent, the number of messages that were successful, and the number of messages that failed.
Total CreateConn checked by SRC
Total number of Create Connection (CRCX) messages that have been checked against the SRC component.
CreateConn accepted by SRC
Number of CRCX messages that have been accepted after being checked by the SRC component.
CreateConn rejected by SRC
Number of CRCX messages that have been rejected by SRC because of resource constraints.
Total ModifyConn checked by SRC
Total number of Modify Connection (MDCX) messages that have been checked against the SRC component.
ModifyConn accepted by SRC
Number of MDCX messages that have been accepted after being checked by the SRC component.
ModifyConn rejected by SRC
Number of MDCX messages that have been rejected by SRC because of resource constraints.
Reason
Specific threshold that was exceeded to cause the rejection.
Num. of requests rejected
Number of requests that have been rejected.
cpu-5sec
CPU utilization for previous 5 seconds threshold was exceeded.
cpu-avg
Average CPU utilization threshold was exceeded.
total-mem
Total memory utilization threshold was exceeded.
io-mem
I/O memory utilization threshold was exceeded.
proc-mem
Processor memory utilization threshold was exceeded.
total-calls
Total number of calls threshold was exceeded.
Related Commands
Command
Description
debug mgcp
Enables debug traces for MGCP errors, events, media, packets, and parser.
mgcp
Allocates resources for the MGCP and starts the daemon.
security password-group
Defines the passwords used by gatekeeper zones and associates them with an ID for gatekeeper-to-gatekeeper authentication.
show mgcp
Displays information for MGCP parameters.
show mgcp connection
Displays information for active MGCP-controlled connections.
show mgcp endpoint
Displays information for MGCP-controlled endpoints.
show mgcp nas
Displays MGCP NAS information for data ports.
show mgcp profile
Displays values for MGCP profile-related parameters.
show modem relay statistics
To display various statistics for modem relay, use the show modem relay statistics command in privileged EXEC mode.
show modem relay statistics { all | phy | pkt | queue | sprt | timer | v14 | v42 } [ call-identifier call-setup-time call-index ]
Syntax Description
all
All statistics associated with the modem-relay feature.
phy
Modem-relay physical layer statistics.
pkt
Modem-relay packetizer statistics.
queue
Modem-relay queue statistics.
sprt
Modem-relay SPRT layer statistics.
timer
Modem-relay timer statistics.
v14
Modem-relay V.14 statistics
v42
Modem-relay V.42 statistics.
call -identifier call-setup-time
(Optional) Value of the system UpTime when the call that is associated with this entry was started. Range is from 0 to 4294967295.
call -identifier call-index
(Optional) Dial-peer identification number used to distinguish between calls with the same setup time. Range is from 0 to 4294967295.
Usage Guidelines
Use this command to display various modem-relay call statistics, including counts of different types of packets, errors, and events, for all modem-relay calls.
Display statistics for a specific modem-relay call by using the call-identifier keyword and specifying the call-setup time and call index of the desired call. Obtain values for the call-setup time and call index from the SetupTime and Index fields at the start of each call record in the show call active command output.
Examples
The following is sample output from the show modem relay statistics v14 command:
Router# show modem relay statistics v14ID:11D6
V14 Layer Statistics
sync_count=47 sync_loss_count=46 min_bundle_size_rcvd_local=1 max_bundle_size_rcvd_local=20 min_bundle_size_rcvd_remote=0 max_bundle_size_rcvd_remote=0 info_bytes_removed_dueto_phy_rcv_q=0 overflow_count_rcv_q=0 info_bytes_removed_dueto_old_age_rcv_q=0 info_bytes_discarded_bad_offset_rcv_q=0 info_bytes_overwrite_rcv_q=0 info_bytes_filled_rcv_q=0 total_bytes_rcv_local=310 min_bundle_size_send_local=0, max_bundle_size_send_local=0 min_bundle_size_send_network=1, max_bundle_size_send_network=22 info_bytes_removed_dueto_phy_xmit_q=0, overflow_count_xmit_q=0 info_bytes_discarded_bad_offset_xmit_q=0 info_bytes_overwrite_xmit_q=0 info_bytes_filled_xmit_q=0, total_bytes_xmit_local=0 Total Modem Relay Call Legs = 1The following is sample output from this command:
Router# show modem relay statistics all call-identifier 43009 1 ID:3 SPRT Layer Statistics sprt_info_frames_rcvd=10 sprt_xid_frames_rcvd=0 sprt_tc0_explicit_acks_rcvd=6 sprt_tc1_explicit_acks_rcvd=122 sprt_tc2_explicit_acks_rcvd=126 sprt_destructive_brks_rcvd=0 sprt_expedited_brks_rcvd=0 sprt_non_expedited_brks_rcvd=0 sprt_info_tframes_sent=9 sprt_info_tframes_resent=0 sprt_xid_frames_sent=0 sprt_tc0_explicit_acks_sent=8 sprt_tc1_explicit_acks_sent=129 sprt_tc2_explicit_acks_sent=132 sprt_destructive_brks_sent=0 sprt_expedited_brks_sent=0 sprt_non_expedited_brks_sent=0 sprt_info_tframes_asked_to_consumed=10 sprt_info_tframes_consumed=10 sprt_info_tframes_failed_to_consume=0 sprt_info_bytes_rcvd=10 sprt_info_bytes_sent=76 sprt_pkts_dropped_intf_busy=289 sprt_min_rexmit_timeout=500 sprt_max_rexmit_timeout=500 Queue Statistics sprt_tc1_rcv_qdrops=0 sprt_tc1_xmit_qdrops=0 sprt_tc2_rcv_qdrops=0 sprt_tc2_xmit_qdrops=0 pktizer_out_qdrops=4 pktizer_in_qdrops=0 v42_xmit_qdrops=0 V42 Layer Statistics vs_chng_dueto_timeouts=0 vs_chng_dueto_rej=0 vs_chng_dueto_rnr_resp_f1_set=0 nr_seq_exception=0 good_rcvd_lapm_pkts=1385 discarded_rcvd_lapm_pkts=0 rejected_rcvd_lapm_pkts=0 v42_rcvd_iframe=9 v42_rcvd_rr=1374 v42_rcvd_rnr=0 v42_rcvd_rej=0 v42_rcvd_srej=0 v42_rcvd_sabme=0 v42_rcvd_dm=0 v42_rcvd_ui=0 v42_rcvd_disc=0 v42_rcvd_ua=1 v42_rcvd_frmr=0 v42_rcvd_xid=1 v42_rcvd_test=0 v42_rcvd_destructive_brk=0 v42_rcvd_expedited_brk=0 v42_rcvd_non_expedited_brk=0 v42_rcvd_brkack=0 v42_sent_iframe=10 v42_sent_rr=1464 v42_sent_rnr=0 v42_sent_rej=0 v42_sent_srej=0 v42_sent_sabme=1 v42_sent_dm=0 v42_sent_ui=0 v42_sent_disc=0 v42_sent_ua=0 v42_sent_frmr=0 v42_sent_xid=1 v42_sent_test=0 v42_sent_destructive_brk=0 v42_sent_expedited_brk=0 v42_sent_non_expedited_brk=0 v42_sent_brkack=0 Physical Layer Statistics num_local_retrain=0 num_remote_retrain=0 num_local_speed_shift=0 num_remote_speed_shift=0 num_sync_loss=0 Packetizer Statistics frames_inprogress=5 good_crc_frames=1385 bad_crc_frames=31 frame_aborts=124 hdlc_sync_detects=1 hdlc_sync_loss_detects=0 bad_frames=0 Timer Statistics xid_timer_cnt=0 sabme_timer_cnt=0 ack_timer_cnt=0 chkpnt_timer_cnt=1333The following is sample output from this command:
Router# show modem relay statistics all ID:3 SPRT Layer Statistics sprt_info_frames_rcvd=10 sprt_xid_frames_rcvd=0 sprt_tc0_explicit_acks_rcvd=6 sprt_tc1_explicit_acks_rcvd=155 sprt_tc2_explicit_acks_rcvd=158 sprt_destructive_brks_rcvd=0 sprt_expedited_brks_rcvd=0 sprt_non_expedited_brks_rcvd=0 sprt_info_tframes_sent=9 sprt_info_tframes_resent=0 sprt_xid_frames_sent=0 sprt_tc0_explicit_acks_sent=8 sprt_tc1_explicit_acks_sent=161 sprt_tc2_explicit_acks_sent=165 sprt_destructive_brks_sent=0 sprt_expedited_brks_sent=0 sprt_non_expedited_brks_sent=0 sprt_info_tframes_asked_to_consumed=10 sprt_info_tframes_consumed=10 sprt_info_tframes_failed_to_consume=0 sprt_info_bytes_rcvd=10 sprt_info_bytes_sent=76 sprt_pkts_dropped_intf_busy=357 sprt_min_rexmit_timeout=500 sprt_max_rexmit_timeout=500 Queue Statistics sprt_tc1_rcv_qdrops=0 sprt_tc1_xmit_qdrops=0 sprt_tc2_rcv_qdrops=0 sprt_tc2_xmit_qdrops=0 pktizer_out_qdrops=4 pktizer_in_qdrops=0 v42_xmit_qdrops=0 V42 Layer Statistics vs_chng_dueto_timeouts=0 vs_chng_dueto_rej=0 vs_chng_dueto_rnr_resp_f1_set=0 nr_seq_exception=0 good_rcvd_lapm_pkts=1910 discarded_rcvd_lapm_pkts=0 rejected_rcvd_lapm_pkts=0 v42_rcvd_iframe=9 v42_rcvd_rr=1899 v42_rcvd_rnr=0 v42_rcvd_rej=0 v42_rcvd_srej=0 v42_rcvd_sabme=0 v42_rcvd_dm=0 v42_rcvd_ui=0 v42_rcvd_disc=0 v42_rcvd_ua=1 v42_rcvd_frmr=0 v42_rcvd_xid=1 v42_rcvd_test=0 v42_rcvd_destructive_brk=0 v42_rcvd_expedited_brk=0 v42_rcvd_non_expedited_brk=0 v42_rcvd_brkack=0 v42_sent_iframe=10 v42_sent_rr=1988 v42_sent_rnr=0 v42_sent_rej=0 v42_sent_srej=0 v42_sent_sabme=1 v42_sent_dm=0 v42_sent_ui=0 v42_sent_disc=0 v42_sent_ua=0 v42_sent_frmr=0 v42_sent_xid=1 v42_sent_test=0 v42_sent_destructive_brk=0 v42_sent_expedited_brk=0 v42_sent_non_expedited_brk=0 v42_sent_brkack=0 Physical Layer Statistics num_local_retrain=0 num_remote_retrain=0 num_local_speed_shift=0 num_remote_speed_shift=0 num_sync_loss=0 Packetizer Statistics frames_inprogress=5 good_crc_frames=1910 bad_crc_frames=31 frame_aborts=124 hdlc_sync_detects=1 hdlc_sync_loss_detects=0 bad_frames=0 Timer Statistics xid_timer_cnt=0 sabme_timer_cnt=0 ack_timer_cnt=0 chkpnt_timer_cnt=1809 Total Modem Relay Call Legs = 1The following is sample output from this command:
Router# show modem relay statistics sprt ID:3 SPRT Layer Statistics sprt_info_frames_rcvd=10 sprt_xid_frames_rcvd=0 sprt_tc0_explicit_acks_rcvd=6 sprt_tc1_explicit_acks_rcvd=177 sprt_tc2_explicit_acks_rcvd=180 sprt_destructive_brks_rcvd=0 sprt_expedited_brks_rcvd=0 sprt_non_expedited_brks_rcvd=0 sprt_info_tframes_sent=9 sprt_info_tframes_resent=0 sprt_xid_frames_sent=0 sprt_tc0_explicit_acks_sent=8 sprt_tc1_explicit_acks_sent=183 sprt_tc2_explicit_acks_sent=187 sprt_destructive_brks_sent=0 sprt_expedited_brks_sent=0 sprt_non_expedited_brks_sent=0 sprt_info_tframes_asked_to_consumed=10 sprt_info_tframes_consumed=10 sprt_info_tframes_failed_to_consume=0 sprt_info_bytes_rcvd=10 sprt_info_bytes_sent=76 sprt_pkts_dropped_intf_busy=403 sprt_min_rexmit_timeout=500 sprt_max_rexmit_timeout=500 Total Modem Relay Call Legs = 1The following is sample output from this command:
Router# show modem relay statistics queue ID:3 Queue Statistics sprt_tc1_rcv_qdrops=0 sprt_tc1_xmit_qdrops=0 sprt_tc2_rcv_qdrops=0 sprt_tc2_xmit_qdrops=0 pktizer_out_qdrops=4 pktizer_in_qdrops=0 v42_xmit_qdrops=0 Total Modem Relay Call Legs = 1The following is sample output from this command:
Router# show modem relay statistics v42 ID:3 V42 Layer Statistics vs_chng_dueto_timeouts=0 vs_chng_dueto_rej=0 vs_chng_dueto_rnr_resp_f1_set=0 nr_seq_exception=0 good_rcvd_lapm_pkts=2442 discarded_rcvd_lapm_pkts=0 rejected_rcvd_lapm_pkts=0 v42_rcvd_iframe=9 v42_rcvd_rr=2431 v42_rcvd_rnr=0 v42_rcvd_rej=0 v42_rcvd_srej=0 v42_rcvd_sabme=0 v42_rcvd_dm=0 v42_rcvd_ui=0 v42_rcvd_disc=0 v42_rcvd_ua=1 v42_rcvd_frmr=0 v42_rcvd_xid=1 v42_rcvd_test=0 v42_rcvd_destructive_brk=0 v42_rcvd_expedited_brk=0 v42_rcvd_non_expedited_brk=0 v42_rcvd_brkack=0 v42_sent_iframe=10 v42_sent_rr=2539 v42_sent_rnr=0 v42_sent_rej=0 v42_sent_srej=0 v42_sent_sabme=1 v42_sent_dm=0 v42_sent_ui=0 v42_sent_disc=0 v42_sent_ua=0 v42_sent_frmr=0 v42_sent_xid=1 v42_sent_test=0 v42_sent_destructive_brk=0 v42_sent_expedited_brk=0 v42_sent_non_expedited_brk=0 v42_sent_brkack=0 Total Modem Relay Call Legs = 1The following is sample output from this command:
Router# show modem relay statistics phy ID:3 Physical Layer Statistics num_local_retrain=0 num_remote_retrain=0 num_local_speed_shift=0 num_remote_speed_shift=0 num_sync_loss=0 Total Modem Relay Call Legs = 1The following is sample output from this command:
Router# show modem relay stat pkt ID:3 Packetizer Statistics frames_inprogress=5 good_crc_frames=2573 bad_crc_frames=61 frame_aborts=150 hdlc_sync_detects=1 hdlc_sync_loss_detects=0 bad_frames=0 Total Modem Relay Call Legs = 1The following is sample output from this command:
Router# show modem relay stat timer ID:3 Timer Statistics xid_timer_cnt=0 sabme_timer_cnt=0 ack_timer_cnt=0 chkpnt_timer_cnt=2750 Total Modem Relay Call Legs = 1Related Commands
Command
Description
debug voip ccapi inout
Traces the execution path through the call control API.
debug vtsp all
Displays all VTSP debugging except statistics, tone, and event.
show call active
Displays active call information for voice calls or fax transmissions in progress.
show call active voice
Displays current call information for a call in progress.
show modems
Displays all modem configurations.