To enable data protection for a circuit emulation (CEM) channel, use the data-protectioncommand in CEM configuration mode. To disable data protection, use the no form of this command.
data-protection
nodata-protection
Syntax Description
This command has no arguments or keywords.
Command Default
Data protection is disabled for a CEM channel.
Command Modes
CEM configuration
Command History
Release
Modification
12.3(7)T
This command was introduced.
Examples
The following example demonstrates how to enable data protection.
Router(config-cem)# data-protection
Related Commands
Command
Description
cem
Enters circuit emulation configuration mode.
clearcem
Clears CEM channel statistics.
showcem
Displays CEM channel statistics.
data-strobe
To specify an input control lead to be monitored as an indicator of valid data, use the data-strobe command in CEM configuration mode. To disable the monitoring of an input control lead, use the no form of this command.
data-strobeinput-lead
{ on | off }
nodata-strobe
Syntax Description
input-lead
Specifies the input lead. The choice of leads depends on whether the port is DCE or DTE.
on
Enables packet creation when the lead is asserted.
off
Enables packet creation when the lead is deactivated.
Command Default
No input control lead is monitored.
Command Modes
CEM configuration
Command History
Release
Modification
12.3(7)T
This command was introduced.
Usage Guidelines
Any input control signal on a serial data port may be configured as a “data strobe” to indicate to the NM-CEM-4SER network module whether ingress data on the port should be encapsulated for transmission or ignored. If the data-strobe command is specified with the on keyword, data packets are created and sent when the input lead is asserted. If the data strobe is off (either intentionally or as a result of the failure of the customer premises equipment [CPE]), no data packets are created, and this results in preservation of bandwidth in the IP network.
This command applies only to serial ports.
Examples
The following example demonstrates how to specify that packets are to be created and sent to the far end only when the DTR input control lead is asserted.
Router(config-cem)# data-strobe dtr on
Related Commands
Command
Description
cem
Enters circuit emulation configuration mode.
clearcem
Clears CEM channel statistics.
control-leadsamplingrate
Configures the sampling rate of input control leads.
control-leadstate
Specifies the state of an output control lead.
showcem
Displays CEM channel statistics.
dce-terminal-timing enable
To prevent phase shifting of the data with respect to the clock when running the line at high speeds and long distances, use the dce-terminal-timingenable command in interface configuration mode. If serial clock transmit external (SCTE) terminal timing is not available from the DTE, use the noform of this command; the
DCE will use its own clock instead of SCTE from the DTE.
dce-terminal-timingenable
nodce-terminal-timingenable
Syntax Description
This command has no arguments or keywords.
Command Default
The DCE uses its own clock.
Command Modes
Interface configuration
Command History
Release
Modification
10.0
This command was introduced.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Usage Guidelines
On the Cisco 4000 router, you can specify the serial Network Interface Module timing signal configuration. When the board is operating as a DCE and the DTE provides terminal timing (SCTE or TT), the dce-terminal-timingenable command causes the DCE to use SCTE from the DTE.
Examples
The following example shows how to prevent phase shifting of the data with respect to the clock:
Router(config)# interface serial 0
Router(config-if)# dce-terminal-timing enable
debug l2protocol-tunnel
To configure the debugging option of Layer 2 Protocol Tunneling (L2PT), use the debugl2protocol-tunnel command in EXEC mode.
If you do not specify a debugging option, all options are enabled.
Command Modes
User EXEC (>)
Command History
Release
Modification
15.2(2)T
This command was introduced.
Examples
The following example shows how to debug the l2protocol-tunnel command:
Router# debug l2protocol-tunnel error
Related Commands
Command
Description
l2protoco-tunnel
Enables Layer 2 protocol tunneling for CDP, STP, or VTP packets on an interface.
show l2protocol-tunnel
Displays information about L2PT ports.
debug platform link-dc
To display debugging messages for the link daughter card, use the debugplatformlink-dccommand in privileged EXEC mode. To disable debugging output, use the no form of this command.
Physical layer (PHY) and SerDes debug information.
transceiver
Pluggable optics module information.
wanphy
WAN PHY driver debug information.
Command Default
Debugging is not enabled.
Command Modes
Privileged EXEC (#)
Command History
Release
Modification
12.2(33)SRD
This command was introduced.
Note
This command applies only to the Cisco 7600 Series Ethernet Services Plus (ES+) line card on the Cisco 7600 series router.
12.2(33)SRD1
This command added the dwdm and wanphy keywords.
Usage Guidelines
Use this command with the remote command command or the attach command in privileged EXEC mode.
Examples
The following examples show the output for both the debug platform link-dc tranceiver command and the debug platform link-dc interrupt command. Notice that the show platform hardware transceiver command shows the status for the port.
Router# remote command module 1 debug platform link-dc tranceiver
Link-DC transceiver debugging is on
Router# remote command module 1 debug platform link-dc interrupt
Link-DC interrupt debugging is on
Router# remote command module 1 show debug
x40g subsystem:
Link-DC transceiver debugging is on
Link-DC interrupt debugging is on
Router# remote command module 1 show platform hardware transceiver status 1
Show status info for port 1:
TenGigabitEthernet1/1:
State: Enabled
Environmental Information - raw values
Temperature: 7616
Tx voltage: 0 in units of 100uVolt
Tx bias: 28722 uA
Tx power: -2 dBm (5441 in units of 0.1 uW)
Rx power: 0 dBm (7712 in units of 0.1 uW)
(AUX1) Laser Temperature: 8704
(AUX2) +3.3V Supply Voltage: 32928
XFP TX is enabled.
XFP TX is soft enabled.
XFP is ready.
XFP is not power down.
XFP is not soft power down.
XFP doesn't have interrupt(s).
XFP is not LOS.
XFP data is ready.
XFP TX path is ready.
XFP TX laser is not in fault condition.
XFP TX path CDR is locked.
XFP RX path is ready.
XFP RX path CDR is locked.
No active alarms
No active warning
Router-dfc1#
*Aug 15 11:20:26.436 PDT: DFC1: TenGigabitEthernet1/1 XFP: show status
*Aug 15 11:20:26.436 PDT: DFC1: TenGigabitEthernet1/1 XFP: show environmental monitoring
*Aug 15 11:20:26.436 PDT: DFC1: pluggable optics read - addr: 50, offset: 60, len: 14, dataptr: 2377A668
*Aug 15 11:20:26.448 PDT: DFC1: pluggable optics read - addr: 50, offset: 6E, len: 2, dataptr: 21AA028E
*Aug 15 11:20:26.452 PDT: DFC1: pluggable optics read - addr: 50, offset: 50, len: 2, dataptr: 2377A6A0
*Aug 15 11:20:26.456 PDT: DFC1: pluggable optics read - addr: 50, offset: 52, len: 2, dataptr: 2377A6A2
Note
The following console log is seen when both the debug platform link-dc tranceiver command and the debug platform link-dc interrupt command are entered (as in the preceding example), and there is a transceiver Rx loss of signal (LOS) event.
Router-dfc1#
*Aug 15 11:23:52.127 PDT: DFC1: x40g_link_dc_interrupt_handler: intr_status 0x8000
*Aug 15 11:23:52.127 PDT: DFC1: x40g_link_xphy_isr: xphy intr intr_st 0x80000
*Aug 15 11:23:52.127 PDT: DFC1: x40g_link_xphy_isr: xphy intr port 1
*Aug 15 11:23:52.127 PDT: DFC1: x40g_xphy_link_status_callout: port 1 link status 0
*Aug 15 11:23:52.131 PDT: DFC1: x40g_link_dc_interrupt_handler: intr_status 0x8000
*Aug 15 11:23:52.131 PDT: DFC1: x40g_link_xphy_isr: xphy intr intr_st 0x80000
*Aug 15 11:23:52.131 PDT: DFC1: x40g_link_xphy_isr: xphy intr port 1
*Aug 15 11:23:52.131 PDT: DFC1: x40g_xphy_link_status_callout: port 1 link status 1
*Aug 15 11:23:52.135 PDT: DFC1: x40g_link_dc_process: interrupt msg_id 6, msg_num 1
*Aug 15 11:23:52.135 PDT: DFC1: x40g_link_dc_interrupt_handler: intr_status 0x8000
*Aug 15 11:23:52.135 PDT: DFC1: x40g_link_xphy_isr: xphy intr intr_st 0x80000
*Aug 15 11:23:52.135 PDT: DFC1: x40g_link_xphy_isr: xphy intr port 1
*Aug 15 11:23:52.135 PDT: DFC1: x40g_xphy_link_status_callout: port 1 link status 0
*Aug 15 11:23:52.135 PDT: DFC1: x40g_link_dc_interrupt_handler: intr_status 0x4000
*Aug 15 11:23:52.135 PDT: DFC1: x40g_link_xcvr_isr: intr_st 0x2, start 0, end 4, type 2,port_offset 0x0
*Aug 15 11:23:52.135 PDT: DFC1: Link xcvr port 1: Rx LOS interrupt
*Aug 15 11:23:52.135 PDT: DFC1: x40g_link_dc_process: interrupt msg_id 2, msg_num 1
*Aug 15 11:23:52.135 PDT: DFC1: Port 2: transceiver Rx LOS event
*Aug 15 11:23:52.147 PDT: DFC1: x40g_link_dc_process: xcvr oir timer timeout
00:12:37: %LINEPROTO-DFC1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/2, changed state to down
*Aug 15 11:24:46.576 PDT: DFC1: x40g_link_dc_interrupt_handler: intr_status 0x4000
*Aug 15 11:24:46.576 PDT: DFC1: x40g_link_xcvr_isr: intr_st 0x2, start 0, end 4, type 2,port_offset 0x0
*Aug 15 11:24:46.576 PDT: DFC1: Link xcvr port 1: Rx LOS interrupt
*Aug 15 11:24:46.576 PDT: DFC1: x40g_link_dc_process: interrupt msg_id 2, msg_num 1
*Aug 15 11:24:46.576 PDT: DFC1: Port 2: transceiver Rx LOS recovered
*Aug 15 11:24:46.580 PDT: DFC1: x40g_link_dc_interrupt_handler: intr_status 0x8000
*Aug 15 11:24:46.580 PDT: DFC1: x40g_link_xphy_isr: xphy intr intr_st 0x80000
*Aug 15 11:24:46.580 PDT: DFC1: x40g_link_xphy_isr: xphy intr port 1
*Aug 15 11:24:46.580 PDT: DFC1: x40g_xphy_link_status_callout: port 1 link status 0
*Aug 15 11:24:46.584 PDT: DFC1: x40g_link_dc_interrupt_handler: intr_status 0x8000
*Aug 15 11:24:46.584 PDT: DFC1: x40g_link_xphy_isr: xphy intr intr_st 0x80000
*Aug 15 11:24:46.584 PDT: DFC1: x40g_link_xphy_isr: xphy intr port 1
*Aug 15 11:24:46.584 PDT: DFC1: x40g_xphy_link_status_callout: port 1 link status 1
*Aug 15 11:24:46.584 PDT: DFC1: x40g_link_dc_process: interrupt msg_id 6, msg_num 1
*Aug 15 11:24:46.600 PDT: DFC1: x40g_link_dc_process: xcvr oir timer timeout
00:13:31: %LINEPROTO-DFC1-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/2, changed state to up
The following example shows the output for the debug platform link-dc dwdm command.
The following example shows the output for the debug platform link-dc wanphy command.
Router-dfc1# debug platform link-dc wanphy
Link-DC WAN PHY debugging is on
*Jan 28 11:59:16.184 PDT: DFC1: Port 1 WIS alarms:
ser 0, plm_p_far 0, ais_p_far 0, lof 0, los 0
rdi 0, ais_l 0, lcd_p 0, plm_p 0, ais_p 0, lop 0
*Jan 28 11:59:17.184 PDT: DFC1: Port 1 WIS alarms:
ser 0, plm_p_far 0, ais_p_far 0, lof 0, los 0
rdi 0, ais_l 0, lcd_p 0, plm_p 0, ais_p 0, lop 0
*Jan 28 11:59:17.184 PDT: DFC1: Port 1 WIS counters: b1 0, b2 0, b3 0, fe_b2 0, fe_b3 0
*Jan 28 11:59:17.184 PDT: DFC1: Port 1 WIS J1RX: 0x0000000000000089.0x302E302E302E3000
...
*Jan 28 11:59:22.288 PDT: DFC1: Port 1 WIS alarms:
ser 0, plm_p_far 0, ais_p_far 0, lof 0, los 0
rdi 0, ais_l 0, lcd_p 0, plm_p 0, ais_p 0, lop 0
*Jan 28 11:59:22.288 PDT: DFC1: Port 1 WIS counters: b1 0, b2 0, b3 0, fe_b2 0, fe_b3 0
*Jan 28 11:59:22.288 PDT: DFC1: Port 1 WIS J1RX: 0x0000000000000089.0x302E302E302E3000
Related Commands
Command
Description
showplatformhardwaretransceiver
Displays transceiver information on a port.
debug platform network-clock
To debug issues related to the network clock, such as alarms, out-of-resource (OOR), and active-standby sources not selected correctly, use the debug platform network-clock command in the privileged EXEC mode. To disable debugging, use the
nono form of this command. .
debugplatformnetwork-clock
nodebugplatformnetwork-clock
Command Default
This command has no arguments or keywords.
Command Modes
Privileged EXEC (#)
Command History
Release
Modification
Cisco IOS XE Release 3.2
This command was integrated into Cisco ASR 1000 Series routers.
Cisco IOS Release 12.2(33)SRE
This command was introduced on the Cisco 7600 Series routers.
Examples
The following example shows how to debug the network clock:
Router(config)# debug platform network-clock
debug platform software ucse
To debug the Cisco UCS E-Series Server (UCSE) platform software and display debug messages, use the
debug platform software ucse command in privileged EXEC mode. To disable debug, use the no form of this command.
debugplatformsoftwareucse
{ all | error | normal }
nodebugplatformsoftwareucse
{ all | error | normal }
Syntax Description
all
Displays all platform debug messages.
error
Displays error debug messages.
normal
Displays normal debug messages.
Command Modes
Privileged EXEC (#)
Command History
Release
Modification
Cisco IOS XE Release 3.9S
This command was introduced on the Cisco UCS E-Series Servers installed in the Cisco 4400 Series Integrated Services Router (ISR).
Usage Guidelines
After you use the debug platform software ucse all command, use the appropriate ucse command to display debug messages.
Examples
The following example shows how to display debug messages for the ucse subslot imc password-reset command:
Router# debug platform software ucse all
Router#
Router# ucse subslot 2/0 imc password-reset
ucse2/0/0
Password reset command sent.
Router#
IMC ACK: UCSE password reset successful for IMC
ACK received for UCSE: Password Reset Command
debug snmp tunnel-mib
To enable the debugging for configuring the IP Tunnel Management Information Base (MIB) through Simple Network Management Protocol (SNMP), use the debugsnmptunnel-mib command in privileged EXEC mode. To disable debugging, use the no form of this command.
debugsnmptunnel-mib
nodebugsnmptunnel-mib
Syntax Description
This command has no arguments or keywords.
Command Modes
Privileged EXEC (#)
Command History
Release
Modification
12.2(33)SRB
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
12.2(33)SB1
This command was integrated into Cisco IOS Release 12.2(33)SB1.
12.2(44)SG
This command was integrated into Cisco IOS Release 12.2(44)SG.
Cisco IOS Release XE 2.1
This command was integrated into Cisco IOS Release XE 2.1.
Usage Guidelines
Use the debugsnmptunnel-mib command to verify whether a tunnel is created or deleted.
Examples
The following is sample output from the debugsnmptunnel-mib command. The output shows that a tunnel is created through SNMP.
Router# debug snmp tunnel-mib
SNMP TUNNEL-MIB debugging is on
k_tunnelInetConfigEntry_get: Entering
k_tunnelInetConfigEntry_get: Exact search
tim_client_tunnel_endpoint_data_get: Entering
tim_client_tunnel_endpoint_data_get: Exact search
tim_client_tunnel_endpoint_data_get: No element found
k_tunnelInetConfigEntry_get: Client service failed
k_tunnelInetConfigEntry_test: Entering
k_tunnelInetConfigEntry_test: Completed
k_tunnelInetConfigEntry_set: Entering
tim_client_tunnel_endpoint_data_get: Entering
tim_client_tunnel_endpoint_data_get: Exact search
tim_client_tunnel_endpoint_data_get: No element found
k_tunnelInetConfigEntry_set: Calling tunnel create
tim_client_tunnel_create: Entering
tim_client_tunnel_create: Completed
default (CEM)
To reset channel options to their default values, use the defaultcommand in CEM configuration mode.
Resets the IP differentiated services code point (DSCP) field to its default value.
iptos
Resets the IP type of service (ToS) field to its default value.
ipprecedence
Resets the IP precedence field to its default value.
payload-compression
Resets payload compression to its default value.
payload-size
Resets payload size to its default value.
signaling
Resets signaling to its default value.
Command Default
The CEM channel options are set at their configured values.
Command Modes
CEM configuration
Command History
Release
Modification
12.3(7)T
This command was introduced for CEM configuration mode.
Examples
The following example demonstrates how to reset CEM channel data protection to its default value.
Router(config-cem)# default data-protection
Related Commands
Command
Description
cem
Enters circuit emulation configuration mode.
clearcem
Clears CEM channel statistics.
data-protection
Enables data protection.
dejitter-buffer
Configures the dejitter buffer size.
idle-pattern
Defines the idle pattern that the channel transmits when it goes down.
payload-compression
Enables payload compression.
payload-size
Configures the payload size.
showcem
Displays CEM channel statistics.
signaling
Enables CAS signaling.
default interface
To reset the configuration of an interface back to its default
values, use the
defaultcommand in global configuration mode.
defaultinterface-typeinterface-number
Syntax Description
interface-type
Type of interface. The interface types that are available
to be reset to their default values will vary depending on the available
interface types on the networking device and the Cisco IOS release that is
installed on the device. Not all possible interface types are documented here.
async--Reconfigures
the specified async interface to its default value.
atm--Reconfigures
the specified ATM interface to its default value.
bvi--Reconfigures
the specified bridge-group virtual interface to its default value.
dialer--Reconfigures
the specified dialer interface to its default value.
ethernet--Reconfigures
the specified Ethernet interface to its default value.
fastethernet--Reconfigures
the specified Fast Ethernet interface to its default value.
fddi--Reconfigures
the specified FDDI interface to its default value.
gigabitethernet--Reconfigures
the specified Gigabit Ethernet interface to its default value.
group-async--Reconfigures
the specified group async interface to its default value.
loopback--Reconfigures
the specified loopback interface to its default value.
null--Reconfigures
the specified null interface to its default value.
pos--Reconfigures
the specified Packet over SONET (POS) interface to its default value.
serial--Reconfigures
the specified serial interface to its default value.
tunnel--Reconfigures
the specified tunnel interface to its default value.
interface-number
Number of the interface, slot, router shelf, unit, port, or
port adaptor if appropriate for the interface type. Slash marks may be required
between elements of this argument.
Command Default
Existing interface configuration values are not reset.
Command Modes
Global configuration
Command History
Release
Modification
11.1
This command was introduced.
12.2(33)SRA
This command was integrated into Cisco IOS Release
12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX
train. Support in a specific 12.2SX release of this train depends on your
feature set, platform, and platform hardware.
Usage Guidelines
The
default command is a general-purpose command
that is not limited to interfaces; it resets defaults based on the command name
that follows it. Use the
default(interface) command when you need to remove any configuration
for a specified interface and reset the interface to its default values.
Examples
The following example demonstrates how to reset serial interface 0 to
its default values.
Router(config)# default serial 0
Related Commands
Commands
Description
interface
Enters interface configuration mode.
define interface-range
To create an interface-range macro, use the
defineinterface-range command in global configuration mode. To remove an interface-range macro, use the
no form of this command.
defineinterface-rangemacro-nameinterface-range
Syntax Description
macro-name
Name of the interface-range macro.
interface-range
Type of interface range.
For a list of valid values, see the “Usage Guidelines” section.
Command Default
Interface-range macro is not configured.
Command Modes
Global configuration (config)
Command History
Release
Modification
12.2(14)SX
This command was introduced.
12.2(17d)SXB
This command was integrated into Cisco IOS XE Release 12.2(17d)SXB.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
15.1(2)SNG
This command was implemented on the Cisco ASR 901 Series Aggregation Services Routers.
Usage Guidelines
The
define interface-range command applies a particular configuration on multiple interfaces and creates multiple logical, and sub interfaces.
An interface range macro name can comprise up to 32 characters.
An interface range for a macro can accept a maximum of five ranges. However, the subinterface range for a macro accepts only one range.
An interface range cannot span slots.
Use the
interface-typeslot/first-interfacelast-interface format to enter the interface range.
Valid values for the
interface-type argument are as follows:
atm—Supported on Cisco 7600 series routers that are configured with a Supervisor Engine 2
ethernet
fastethernet
ge-wan—Supported on Cisco 7600 series routers that are configured with a Supervisor Engine 2
gigabitethernet
loopback
port-channelinterface-number—Valid values are from 1 to 256
pos—Supported on Cisco 7600 series routers that are configured with a Supervisor Engine 2
tengigabitethernet
tunnel
vlanvlan-id—Valid values are from 1 to 4094
Examples
The following example shows how to create a multiple-interface macro:
Executes a command on multiple ports at the same time.
dejitter-buffer
To configure the size of the dejitter buffer, use the dejitter-buffer command in CEM configuration mode. To restore the dejitter buffer to its default size, use the no form of this command.
dejitter-buffersize
nodejitter-buffer
Syntax Description
size
Size, in milliseconds, of the dejitter buffer. The range is from 5 to 500. The default is 60. For Cisco ASR 901 Series Aggregation Services Routers, the range is from 4 to 500; the default is 4.
Command Default
The dejitter buffer defaults to 60 milliseconds. For Cisco ASR 901 Series Aggregation Services Routers, the default is 4.
Command Modes
CEM configuration
Command History
Release
Modification
15.1(2)SNG
This command was implemented on Cisco ASR 901 Series Aggregation Services Routers.
15.1(2)SNG
This command was implemented on Cisco ASR 901 Series Aggregation Services Routers.
Examples
The following example shows how to set the dejitter buffer to 200 milliseconds.
Router(config-cem)# dejitter-buffer 200
The following example shows how to specify the size of the dejitter buffer to 10 milliseconds on the Cisco ASR 901 Series Aggregation Services Router:
Router# configure terminal
Router(config)# interface cem 0/0
Router(config-if)# no ip address
Router(config-if)# cem 0
Router(config-if-cem)# dejitter-buffer 10
Router(config-if-cem)# xconnect 10.10.10.10 200 encapsulation mpls
Router(config-if-cem-xconn)# exit
Router(config-if-cem)# exit
Router(config-if)# exit
Router(config)# exit
Related Commands
Command
Description
cem
Enters circuit emulation configuration mode.
clearcem
Clears CEM channel statistics.
clearcem
Clears CEM channel statistics.
clearcem
Clears CEM channel statistics.
showcem
Displays CEM channel statistics.
delay (interface)
To set a delay value for an interface, use the delay command in interface configuration mode. To restore the default delay value, use the no form of this command.
delaytens-of-microseconds
nodelay
Syntax Description
tens-of-microseconds
Integer that specifies the delay in tens of microseconds for an interface or network segment. To see the default delay, use the showinterfaces command.
Command Default
Default delay values may be displayed with the showinterfacesEXEC command.
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Cisco IOS XE Release 3.2S
This command was modified. Support was added for this command in virtual network interface configuration mode.
Examples
The following example shows how to set a delay of 30,000 microseconds on serial interface 3:
Router(config)# interface serial 3
Router(config-if)# delay 3000
Related Commands
Command
Description
showinterfaces
Displays the statistical information specific to a serial interface.
delay-req interval
To specify a recommended interval for Precision Time Protocol member
devices to send delay request messages, use the
delay-reqinterval command in PTP clock port configuration
mode. To remove a delay request interval configuration, use the
no form of this command.
delay-reqintervalinterval-valueunicast
nodelay-reqintervalinterval-valueunicast
Syntax Description
interval-value
Specifies the length of the interval for delay request
messages. The intervals are set using log base 2 values, as follows:
4--1 packet
every 16 seconds
3--1 packet
every 8 seconds
2--1 packet
every 4 seconds
1--1 packet
every 2 seconds
0--1 packet
every second
-1--1 packet
every 1/2 second, or 2 packets per second
-2--1 packet
every 1/4 second, or 4 packets per second
-3--1 packet
every 1/8 second, or 8 packets per second
-4--1 packet
every 1/16 seconds, or 16 packets per second.
-5--1 packet
every 1/32 seconds, or 32 packets per second.
-6--1 packet
every 1/64 seconds, or 64 packets per second.
The recommended value is -6.
unicast
(Optional) Specifies that the device send PTP delay request
messages using unicast mode.
Command Default
The default value is -4 (16 packets per second).
Command Modes
PTP clock-port configuration (config-ptp-port)
Command History
Release
Modification
15.0(1)S
This command was introduced.
Usage Guidelines
This configuration is only required when an interface is in PTP slave
mode.
Examples
The following example shows how to use the
delay-req command:
To add a description to an E1 or T1 controller or the Channelized T3 Interface Processor (CT3IP) in Cisco 7500 series routers, use the
descriptioncommand in controller configuration mode. To remove the description, use the
noform of this command.
descriptionstring
nodescription
Syntax Description
string
Comment or description (up to 80 characters) to help you remember what is attached to an interface.
Command Default
No description is added.
Command Modes
Controller configuration
Command History
Release
Modification
10.3
This command was introduced.
11.3
This command was modified to include the CT3IP controller.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Usage Guidelines
The
description command is meant solely as a comment to be put in the configuration to help you remember what certain controllers are used for. The description affects the CT3IP and Multichannel Interface Processor (MIP) interfaces only and appears in the output of the
showcontrollere1,
showcontrollert1,showcontrollert3, andshowrunning-configEXEC commands.
Examples
The following example shows how to add a description for a 3174 controller:
Router(config)# controller t1
Router(config-controller)# description 3174 Controller for test lab
Related Commands
Command
Description
showcontrollerse1
Displays information about the E1 links supported by the NPM (Cisco 4000) or MIP (Cisco 7500 series).
showcontrollerst1
Displays information about the T1 links.
showcontrollerst3
Displays information about the CT3IP on Cisco 7500 series routers.
description (interface)
To add a description to an interface configuration, use the descriptioncommand in interface configuration mode. To remove the description, use the noform of this command.
descriptionstring
nodescription
Syntax Description
string
Comment or a description to help you remember what is attached to this interface. This string is limited to 238 characters.
Command Default
No description is added.
Command Modes
Interface configuration
Command History
Release
Modification
9.21
This command was introduced.
Usage Guidelines
The description command is meant solely as a comment to be put in the configuration to help you remember what certain interfaces are used for. The description appears in the output of the following EXEC commands:morenvram:startup-config,
showinterfaces, andmoresystem:running-config
Examples
The following example shows how to add a description for a T1 interface:
interface serial 0
description Fractional T1 line to remote office -- 128 kbps
Related Commands
Command
Description
morenvram:startup-config
Displays the startup configuration file contained in NVRAM or specified by the CONFIG_FILE environment variable.
moresystem:running-config
Displays the running configuration.
showinterfaces
Displays statistics for all interfaces configured on the router or access server.
diagnostic level
To turn on power-on diagnostic tests for the network service engines (NSEs) installed in a Cisco 7300 series router, use the diagnosticlevel command in privileged EXEC configuration mode. There is no no form of this command.
diagnosticlevel
{ power-on | bypass }
Syntax Description
power-on
Power-on diagnostic tests are performed at system bootup on the NSEs.
bypass
No diagnostic tests are performed. This is the default.
Command Default
No diagnostic tests are performed.
Command Modes
Privileged EXEC
Command History
Release
Modification
12.1(10)EX2
This command was introduced.
12.2(18)S
This command was introduced on Cisco 7304 routers running Cisco IOS Release 12.2 S.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Usage Guidelines
Use this command to enable power-on diagnostic tests to run on the installed NSEs of a Cisco 7300 series router when the system is booted. It is recommended that you issue this command only if you are experiencing problems with an NSE and are planning on rebooting the router. Issuing this command causes an increase in the boot time.
Examples
The following example shows how to enable diagnostic power-on tests:
diagnostic level power-on
The following sample output shows the output that is displayed upon system bootup after a power cycle or router crash:
.
.
.
System Power On Diagnostics
DRAM Size ....................128 MB
Testing DRAM..................Passed
Level2 Cache .................Present
Testing Level2 Cache (256 KB)Passed
Level3 Cache .................Present
Testing Level3 Cache (1024 KB)Passed
System Power On Diagnostics Complete
Note
This output is displayed when the system is booting, not when the command is issued.
Related Commands
Command
Description
debugredundancy
Enables NSE redundancy debugging.
showc7300
Displays the types of cards (NSE and line cards) installed in a Cisco 7300 series router.
showredundancy(7300)
Displays redundancy information for the active and standby NSEs.
dial-tdm-clock
To configure the clock source and priority of the clock source used by the time-division multiplexing (TDM) bus on the dial shelf of the Cisco AS5800, use the dial-tdm-clock command in global configuration mode. To return the clock source and priority to the default values, use the no form of this command.
Specifies the priority of the clock source. The range is from 1 to 50. Priority 1 is the highest priority, and 50 is the lowest.
external
Specifies the priority of an external clock source. The external clock source is connected to the front panel of the Dial Shelf Controller (DSC) card.
e1 | t1}
[120ohm]
Specifies priority of the E1 (2.048 MHz) or T1 (1.54 MHz) external clock source. The default value of the external coaxial cable impedance is 75 ohm. Specify the 120ohmoption if a 120 ohm coaxial cable is connected.
freerun
Specifies the priority of the local oscillator clock source.
trunk-slotslot
Specifies the priority of the trunk card to provide the clock source. The slot number is from 0 to 5 (these are the only slots capable of providing clock sources).
portport
Specifies the controller number on the trunk used to provide the clock source. The port number is from 0 to 28. The T1 and E1 trunk cards each have 12 ports. The T3 trunk card has 28 ports.
line
{0 | 1
(Optional) Specifies the optical port. If the physical optical port is 0, theline value is also 0.
Command Default
If no clock sources are specified, the software selects the first available good clock source on a trunk port.
Command Modes
Global configuration
Command History
Release
Modification
11.3(2)AA
This command was introduced.
12.2(15)T
The line keyword was added.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Usage Guidelines
The TDM bus in the backplane on the dial shelf must be synchronized to the T1/E1 clocks on the trunk cards. The DSC card on the dial shelf provides hardware logic to accept multiple clock sources as input and use one of them as the primary source to generate a stable, PPL synchronized output clock. The input clock can be any of the following sources:
Trunk port in slots 0 through 5 (up to 12 can be selected (two per slot)
An external T1 or E1 clock source fed directly through a connector on the DSC card
A free running clock from an oscillator in the clocking hardware on the DSC card
The clock commands are listed in the configuration file with the highest priority listed first.
If the current primary clock source is good, specifying another clock source of higher priority does not cause the clock source to switch to the higher priority clock source. The new higher priority clock source is used as a backup clock source. This prevents switching of the clock source as you enter multiple dial-tdm-clock priority configuration commands in random order. Also, it is important not to disturb the existing clock source as long as it is good. To force the new higher priority clock source to take over from a currently good primary clock source, configure the new clock source and use the no dial-tdm-clock priority command to remove the current primary clock source.
To display the current primary and backup clocks along with their priorities, use the showdial-shelfclocksEXECcommand.
Examples
In the following example, an external clock source is set at priority 1 and the trunk card in slot 4, port 1 is set at priority 5:
Displays information about the dial shelf, including clocking information.
dot1q tunneling ethertype
To define the Ethertype field type used by peer devices when implementing Q-in-Q VLAN tagging, use the
dot1qtunnelingethertypecommand in interface configuration mode. To remove the VLAN tag Ethertype, use the
no form of this command.
The Ethertype field used by peer devices when implementing Q-in-Q VLAN tagging is 0x8100.
Command Modes
Interface configuration (config-if)
Command History
Release
Modification
12.3(7)T
This command was introduced.
12.3(7)XI1
This command was implemented on the Cisco 10000 series routers.
12.2(31)SB2
This command was integrated into Cisco IOS Release 12.2(31)SB2.
12.2(33)SRC
This command was integrated into Cisco IOS Release 12.2(33)SRC.
Cisco IOS XE Release 2.2
This command was integrated into Cisco IOS XE Release 2.2.
Usage Guidelines
Use the
dot1qtunnelingethertype command if the peer switching devices are using an Ethertype field value of 0x9100 or 0x9200. All Cisco switching devices use the default Ethertype field value of 0x88A8. The Cisco 10000 series router also supports the 0x9200 Ethertype field value.
Note
On the Cisco 10000 series router, the Ethertype field for the outer VLAN ID can be changed, but the Ethertype field for the inner VLAN ID cannot be changed.
This command is used with the IEEE 802.1Q-in-Q VLAN Tag Termination feature in which double VLAN tagging is configured using the
encapsulationdot1q command. 802.1Q double tagging allows a service provider to use a single VLAN to support customers who have multiple VLANs.
Examples
The following example shows how to configure an Ethertype field as 0x9100:
Enables 802.1Q encapsulation of traffic on a specified subinterface or range of subinterfaces.
interface
Configures an interface and enters interface configuration mode.
down-when-looped
To configure an interface to inform the system that it is down when loopback is detected, use the down-when-loopedcommand in interface configuration mode.
down-when-looped
Syntax Description
This command has no arguments or keywords.
Command Default
Disabled
Command Modes
Interface configuration
Command History
Release
Modification
10.0
This command was introduced.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Usage Guidelines
This command is valid for High-Level Data Link Control (HDLC) or PPP encapsulation on serial and High-Speed Serial Interface (HSSI) interfaces.
This command does not have a no form.
Backup Interfaces
When an interface has a backup interface configured, it is often desirable that the backup interface be enabled when the primary interface is either down or in loopback. By default, the backup is enabled only if the primary interface is down. By using the down-when-looped command, the backup interface will also be enabled if the primary interface is in loopback.
Testing an Interface with the Loopback Command
If testing an interface with the loopback command, or by placing the DCE into loopback, the down-when-looped command should not be configured; otherwise, packets will not be transmitted out the interface that is being tested.
Examples
The following example shows how to configure interface serial 0 for HDLC encapsulation. The interface is then configured to let the system know that it is down when in loopback mode.
Configures an interface as a secondary or dial backup interface.
loopback(E3controller)
Diagnoses equipment malfunctions between an interface and a device.
ds0-group (J1 controller)
To configure channelized J1 time slots, use theds0-groupcommandincontroller configuration mode. To remove the DS0 group, use theno form of this command.
Specifies the DS0 time slot range of values from 1 to 31 for J1 interfaces. Time slot 16 is reserved for signaling.
typeexternal-signaling
Specifies that the signaling traffic comes from an outside source. The signaling method selection for type depends on the connection that you are making.
Command Default
No DS0 group is defined.
Command Modes
Controller configuration
Command History
Release
Modification
11.2
This command was originally the cas-group command.
12.0(1)T
The cas-group command was introduced for the Cisco 3600 series.
12.0(5)XE
The command was renamedds0-group on the Cisco AS5300 and on the Cisco 2600 and Cisco 3600 series.
12.0(7)T
The command was integrated into the Cisco IOS Release 12.0(7)T.
12.2(8)T
The command was introduced as a J1 configuration command for the Cisco 2600 and Cisco 3600 series.
Usage Guidelines
The ds0-group command replaces the existing cas-group command. Making the command generic allows flexibility and scalability. It is not restricted to channel associated signaling (CAS) or channel bundling.
The ds0-group command automatically creates a logical voice port that is numbered as follows on Cisco 2600 and Cisco 3600 series routers: slot/port:ds0-group-no. Although only one voice port is created for each group, applicable calls are routed to any channel in the group.
Examples
The following example is sample output from the showcontrollersj1command on the Cisco 3660 series after channelized J1 time slots have been configured:
Router(config-controller)# ds0-group 1 timeslots 1-15,17-31 type e&m-wink-start
Router(config-controller)# end
Router# show controllers j1
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(1), cp
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(2), cp
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(3), cp
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(4), cp
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(5), cp
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(6), cp
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(7), cp
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(8), cp
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(9), cp
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(10), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(11), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(12), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(13), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(14), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(15), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(17), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(18), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(19), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(20), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(21), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(22), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(23), p
*Mar 1 03:12:26.259: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(24), p
*Mar 1 03:12:26.263: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(25), p
*Mar 1 03:12:26.263: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(26), p
*Mar 1 03:12:26.263: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(27), p
*Mar 1 03:12:26.263: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(28), p
*Mar 1 03:12:26.263: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(29), p
*Mar 1 03:12:26.263: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(30), p
*Mar 1 03:12:26.263: %LINK-3-UPDOWN: Interface recEive and transMit3/0:0(31), p
Related Commands
Command
Description
ds0busyout
Busyouts one or more signal level 0s (DS0s).
dsl-group
To create and configure a digital subscriber line (DSL) group, and
enter config-controller-dsl-group mode, or to automatically configure an ATM
group, use the
dsl-groupcommand in
configuration controller mode. To disable the DSL group, use the
no form of this command.
(Optional) DSL group number. The DSL group number can be
one of the following numbers:
0
1
efm-bond
(Optional) Defines the DSL group as Ethernet First Mile
(EFM) group bonding group.
link-number
(Optional) Link number of the pair. Link number options are
limited to one of the following choices, based on the hardware interface and
the desired DSL group:
HWIC-4SHDSL-E
EFM-bond DSL Group
0
1
2
3
Any combination
of the numbers 0, 1, 2, and 3
1-Pair DSL Group
0
1
2
3
In the case of 1-pair DSL group (2-wire), only one pair
needs to be configured.
HWIC-4SHDSL
IMA DSL Group
0
1
2
3
Any combination
of the numbers 0, 1, 2, and 3
M-Pair DSL Group
0-1
0-2
0-3
2-Pair DSL Group
0-1
2-3
1-Pair DSL Group
0
1
2
HWIC-2SHDSL
DSL Group 0
0
0-1
DSL Group 1
1
auto
(Optional) Automatically assigns the Central Office’s (CO)
wire configuration to an ATM DSL group on the Customer Premise Equipment (CPE).
default
(Optional) Sets a command to the default values.
exit
(Optional) Exits DSL group command mode.
no
(Optional) Negates a command or set its defaults.
shdsl
(Optional) Configures the symmetric g.shdsl.
4-wire
(Optional) Configures the 4-wire symmetric g.shdsl.
annex
(Optional) Configures the annex symmetric g.shdsl.
Command Default
No DSL group is defined or automatically configured.
Command Modes
Configuration controller (config-controller)
Configuration controller DSL group (config-controller-dsl-group)
Command History
Release
Modification
12.4(15)T
This command was introduced for the Cisco HWIC-4SHDSL and
HWIC-2SHDSL running on the Cisco 1841 router and the Cisco 2800 and 3800 series
access routers.
15.1(1)T
This command was modified to support automatic
configuration of Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841
router and the Cisco 2800 and 3800 series access routers.
Added
dsl-grouppairslink-number
[efm-bond] for the Cisco HWIC-4SHDSL-E.
15.1(1)T1
This command was modified. The auto configuration options
default,exit,no,
and
shdslwere added to the dsl-group.
Usage Guidelines
Use the
dsl-group command in configuration controller
mode to define the DSL group, and manually configure the DSL group from
configuration controller DSL group mode. Use the
dsl-groupauto command to
automatically adopt the Central Office (CO) wire configuration on an ATM DSL
group. Use the
dsl-grouppairs to define the DSL
group as Ethernet First Mile (EFM) group bonding group.
Note
Automatic configuration is not supported on IMA groups.
Automatic configuration is limited to only one DSL group and ATM
interface. After a group is automatically configured, no other group can be
created. All manually created groups must be deleted before creating an
automatic configuration group.
Examples
The following example shows how to use the dsl-group command to
create an IMA-DSL group and enter configuration controller DSL group mode:
Router(config-controller)# dsl-group 1 pairs 0-1 ima
Router(config-controller-dsl-group)#
Sep 14 13:15:40.285:%HWIC_SHDSL-5-DSLGROUP_UPDOWN: SHDSL 0/2/0 dsl-group(1) state changed to down.
Sep 14 13:15:42.285:%LINK-3-UPDOWN: Interface ATM0/2/IMA1, changed state to down
Sep 14 13:15:43.285:%LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2/IMA1, changed state to down
The following example shows how to use the dsl-group auto command to
automatically adopt the Central Office (CO) configuration on an ATM group:
Router(config-controller)# dsl-group auto
Router(config-controller-dsl-group-auto)#
*May 14 18:56:33.136: %HWIC_SHDSL-5-DSLGROUP_UPDOWN: SHDSL 0/0/0 dsl-group(0) state changed to down.
*May 14 18:56:35.136: %LINK-3-UPDOWN: Interface ATM0/0/0, changed state to down
*May 14 18:56:36.136: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0/0,
changed state to down
The following example shows how to configure a single-pair DSL group
and enters the configuration controller DSL group mode:
Configures a controller for SHDSL mode and enters
configuration controller mode.
ima group
Defines physical links as IMA group members.
ima group clock-mode
Sets the clock mode for an IMA group.
ima link
Defines physical links in an IMA group.
shdsl 4-wire mode enhanced
Defines the SHDSL to use enhanced mode in a 2-pair DSL
group.
shdsl annex
Defines the SHDSL G.991.2 standard.
shdsl rate
Defines the SHDSL rate.
show controller shdsl
Displays the status of the controller that is configured
for SHDSL mode.
dsl-mode shdsl symmetric annex
To specify the operating mode of the digital subscriber line (DSL) controller, use the dsl-modeshdslsymmetricannexcommand in controller configuration mode.
To specify the line coding type of the DSL controller, use the dsl-modeshdslsymmetricannexcodingcommand in controller configuration mode. To return the DSL to the default Annex A, use the no form of the command.
dsl-modeshdslsymmetricannexmode
[ codingtype ]
nodsl-modeshdslsymmetricannexmode
[ codingtype ]
Syntax Description
mode
Sets the DSL operating mode. The valid values are:
a: Supports Annex A of the G.991.2 standard for North America. This is the default.
b: Supports Annex B of the G.991.2 standard for Europe.
a-b: Supports Annex A or B. For CPE mode only. Not supported in CO mode. Selected when the line trains.
a-b-anfp: Supports Annex A or B-ANFP. For CPE mode only. Not supported in CO mode. Selected when the line trains.
b-anfp: Supports Annex B-ANFP.
f: Supports Annex F, 2-wire mode, line 0 only.
f-g: Supports Annex F-G, 2-wire mode, line 0 only.
g: Supports Annex G, 2-wire mode, line 0 only.
coding
TCPAM line coding.
Type
The valid values are:
16bit-TCPAM: Sets the line coding to16 bit-TCPAM.
32bit-TCPAM: Sets the line coding to 32 bit-TCPAM.
AUTO-TCPAM: Detects the central office coding type.
The annex defaults to A for North America.
Command Modes
Controller configuration (config-controller)
Command History
Release
Modification
12.3(4)XD
This command was introduced on Cisco 2600 series and Cisco 3700 series routers.
12.3(4)XG
This command was integrated into the Cisco IOS Release 12.3(4)XG on the Cisco 1700 series routers.
12.3(7)T
This command was integrated into Cisco IOS Release 12.3(7)T on Cisco 2600 series, Cisco 3631, and Cisco 3700 series routers.
12.3(11)T
Support for the following additional annex parameters was integrated into Cisco IOS Release 12.3(11)T to support Cisco 1700, Cisco 2600, Cisco 2800, Cisco 3700, and Cisco 3800 series routers:
b
a-b
a-b-anfp
b-anfp
12.3(14)T
This command was implemented on Cisco 1800 series routers.
12.4(15)T
Support for the following additional annex parameters was integrated into Cisco IOS Release 12.X(X)T to support Cisco to support Cisco 1700, Cisco 2600, Cisco 2800, Cisco 3700, and Cisco 3800 series routers:
f
f-g
g
12.4(20)T
Support for codingtype parameters was added.
Usage Guidelines
This command is used to configure the DSL controller interface to operate in a specified DSL mode and to set regional operating parameters. The shdsl keyword is used to set the mode to SHDSL and configures multirate, high-speed DSL per ITU G.991.2. The symmetric keyword configures the controller to symmetric mode. The annex keyword configures the controller to use regional operating parameters. The regional operating parameters default to North America. The coding keyword configures the controller Trellis Encoded Pulse Amplitude Modulation (TCPAM) line coding type.
Examples
The following example displays the use of the controllerdsl0/0commandto configure the controller in the router configured on the central office (CO) side. Use the dsl-modeshdslsymmetricannexbcommand to configure the controller for multirate, high-speed DSL with symmetric mode for European operating parameters.
Router# configure terminal
Router(config)# controller dsl 0/0
Router(config-controller)# line-term co
Router(config-controller)# dsl-mode shdsl symmetric annex b
Router(config-controller)# mode atm
Router(config-controller)#
00:22:07: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to down
Router(config-controller)# line-mode 4-wire
00:23:25: %CONTROLLER-5-UPDOWN: Controller DSL 0/0, changed state to up
00:23:31: %LINK-3-UPDOWN: Interface ATM0/0, changed state to up
00:23:32: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to up
The following example uses the dsl-modeshdslsymmetricannexcommandtoconfigurethecontrollerfor2-wireline0,annexF,AUTO-TCPAMlinecoding.
Router> enable
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# controller dsl 0
Router(config-controller)# line-mode 2-wire line-zero
Router(config-controller)# dsl-mode shdsl symmetric annex f coding ?
16bit-TCPAM 16bit-TCPAM line coding
32bit-TCPAM 32bit-TCPAM line coding
AUTO-TCPAM AUTO-TCPAM line coding
Router(config-controller)# dsl-mode shdsl symmetric annex f coding auto-tcpam
Router(config-controller)#
Router#
Related Commands
Command
Description
controllerdsl
Configures the DSL controller.
dsu bandwidth
To specify the maximum allowable bandwidth used by a T3 or E3
controller or the PA-T3 and PA-E3 port adapters, use the
dsubandwidthcommand in interface configuration mode. To return to the
default bandwidth, use the
no form of this command.
dsubandwidthkbps
nodsubandwidth
Syntax Description
kbps
Maximum bandwidth, in kbps. Range is from 22 to 44736.
Default values are as follows:
34,010 for E3
or PA-E3
44,210 for T3
44,736 for
PA-T3
34,368 kbps for
E3 on a Cisco_10000 Series Router
44,210 kbps for
T3 on a Cisco_10000 Series Router
E3 or PA-E3 Port Adatpters
34,010 kbps
44,210 kbps
44,736 kbps
34,368 kbps for E3
44,210 kbps for T3
Command Modes
Interface configuration
Command History
Release
Modification
11.1CA
This command was introduced.
12.2(11)YT
This command was integrated into Cisco IOS Release
12.2(11)YT and implemented on the following platforms: Cisco 2650XM, Cisco
2651XM, Cisco 2691, Cisco 3660 series, Cisco 3725, and Cisco 3745 routers.
12.2(15)T
This command was integrated into Cisco IOS Release
12.2(15)T.
12.2(31)SB
This command was integrated into Cisco IOS Release
12.2(31)SB.
12.2(33)SRA
This command was integrated into Cisco IOS Release
12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX
train. Support in a specific 12.2SX release of this train depends on your
feature set, platform, and platform hardware.
Usage Guidelines
Local and Remote Bandwidths
The local interface configuration must match the remote interface
configuration. For example, if you reduce the maximum bandwidth to 16,000 on
the local port, you must also do the same on the remote port.
The
dsubandwidthcommand reduces the bandwidth by padding the E3 and T3 frame.
Verifying DSU Bandwidth
To verify the data service unit (DSU) bandwidth configured on the
interface, use the show interfaces serial user EXEC command.
G.751 Framing
When G.751 framing is used, DSU bandwidth can be used to select a
payload subrate from 34,010 kbps down to 22 kbps. Before framing bypass can be
used, a DSU bandwidth of 34,010 kbps must be configured.
Continuous Range of Bandwidth
Even though Cisco_IOS software allows you to configure a continuous
range of bandwidths in subrate modes, vendors support bandwidths only in
quantums (for example, in an E3 digital link, bandwidth must be in multiples of
358 kbps). Therefore, the software sets the user-configured bandwidth to the
closest vendor-supported bandwidth. Use the show interfaces serial
slot/port command to display the actual bandwidth
that is configured.
Subrates
The user-configured subrate mode, subrate bandwidth, actual subrate
bandwidth configured, and scramble configuration are displayed near the end of
the show interfaces serial command output.
DSU Modes and Vendor-Supported Bandwidths
The following table shows DSU modes and vendor-supported bandwidths.
Mode
DSU
Bandwidth Range
Bandwidth Multiples
0
Digital Link or Cisco
358-34,010 kbps for E3
300-44,210 kbps for T3
358 kbps
300.746 kbps
1
ADC Kentrox T3/E3 IDSU
1000-34,010 kbps for E3
1500-44,210 kbps for T3
500 kbps
500 kbps
2
Larscom Access T45
3100-44,210 kbps
3158 kbps
3
Adtran T3SU 300
75-44,210 kbps
75.186 kbps
4
Verilink HDM 2182
1500-44,210 kbps
1579 kbps
Examples
The following example sets the maximum allowable DSU bandwidth to
16,000 kbps on interface 1/0/0:
Router(config)# interface serial 1/0/0
Router(config-if)# dsu bandwidth 16000
The following example shows the user-configured subrate bandwidth and
the actual configured subrate bandwidth as displayed in the output of the show
interfaces serial command:
Router# show interfaces serial
Serial1/0 is up, line protocol is up
Hardware is DSXPNM Serial
MTU 1500 bytes, BW 44210 Kbit, DLY 20000 usec,
reliability 253/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive not set
DTR is pulsed for 0 seconds on reset, Restart-Delay is 1637167 secs
Last input 04:59:04, output 04:59:04, output hang never
Last clearing of "show interface" counters 00:00:02
Input queue:0/75/0/0 (size/max/drops/flushes); Total output drops:0
Queueing strategy:fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DSU mode 0, bandwidth 34010, real bandwidth 34010, scramble 0
Related Commands
Command
Description
showinterfacesserial
Displays information that is specific to the interface
hardware.
dsu mode
To specify the interoperability mode used by a T3 or E3 controller or
the PA-T3 and PA-E3 port adapters, use the
dsumodecommand in interface configuration mode. To return to the
default mode, use the
no form of this command.
Sets the interoperability mode to 0. This is the default.
Specify mode 0
to connect an E3 controller to another E3 controller or to a Digital Link data
service unit (DSU) DL3100.
Specify mode 0
to connect a PA-E3 port adapter to another PA-E3 port adapter or to a DL3100.
Specify mode 0
to connect a PA-T3 port adapter to another PA-T3 port adapter or to a DL3100.
1
Sets the interoperability mode to 1. Specify mode 1 to
connect an E3 or T3 controller or a PA-E3 or PA-T3 port adapter to a Kentrox
DSU.
2
Sets the interoperability mode to 2. Specify mode 2 to
connect a T3 controller or a PA-T3 port adapter to a Larscom DSU.
3
Sets the interoperability mode to 3. Specify mode 3 to
connect a T3 controller to an Adtran T3SU 300.
4
Sets the interoperability mode to 4. Specify mode 4 to
connect a T3 controller to a Verilink HDM 2182.
adtran
Connects a T3 interface to an Adtran DSU.
cisco
Connects an E3 or T3 interface to a Cisco DSU.
digital-link
Connects an E3 or T3 interface to a Digital Link DSU.
kentrox
Connects an E3 or T3 interface to a Kentrox DSU.
larscom
Connects a T3 interface to a Larscom DSU.
verilink-highbit
Connects a T3 interface to a Verilink High Bit DSU.
verilink-lowbit
Connects a T3 interface to a Verilink Low Bit DSU.
Cisco 10000 Series Router
0
cisco
Command Modes
Interface configuration
Command History
Release
Modification
11.1CA
This command was introduced.
12.2(11)YT
This command was integrated into Cisco IOS Release
12.2(11)YT and implemented on the following platforms for E3 and T3
controllers: Cisco 2650XM, Cisco 2651XM, Cisco 2691, Cisco 3660 series, Cisco
3725, and Cisco 3745 routers.
12.2(15)T
This command was integrated into Cisco IOS Release
12.2(15)T.
12.2(31)SB
This command was integrated into Cisco IOS Release
12.2(31)SB.
12.2(33)SRA
This command was integrated into Cisco IOS Release
12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX
train. Support in a specific 12.2SX release of this train depends on your
feature set, platform, and platform hardware.
Usage Guidelines
Scrambling Support in DSU Mode 1
DSU mode 1 refers to Kentrox mode. If DSU mode is used on a T3 serial
interface and the bandwidth is greater than or equal to 35,000 bits per second
(bps), the scrambling option is not supported. Likewise, if DSU mode 1 is used
for an E3 serial interface and the bandwidth is greater than or equal to 24,510
bps, scrambling is not supported.
Match Local and Remote DSU Configurations
The local interface configuration must match the remote interface
configuration. For example, if you define the DSU interoperability mode as 1 on
the local port, you must also do the same on the remote port.
Know the DSU Type
You must know what type of DSU is connected to the remote port to
determine if it interoperates with an E3 or T3 controller or a PA-E3 or PA-T3
port adapter. The
dsumode command enables and improves interoperability
with other DSUs.
Verify DSU Mode
To verify the DSU mode configured on the interface, use the
showcontrollersserial or
showinterfacesserial user EXEC commands.
Cisco 10000 Series Router
Only Cisco, Digital Link, and Kentrox DSUs are supported on E3
interfaces.
Examples
Examples
The following example sets the DSU mode to 1 on interface 1/0/0:
Router(config)# interface serial 1/0/0
Router(config-if)# dsu mode 1
Examples
The following example shows the configuration for a serial interface
configured in DSU mode 1. The bandwidth is set higher than that supported by
the Kentrox firmware allows for scrambling. therefore, the scrambling option is
not supported in this configuration.
Router(config
)#
interface serial 1/0/0
Router(config-if)# mtu 4474
Router(config-if)# ip address 192.168.93.114 255.255.255.252
Router(config-if)# ip mtu 4470
Router(config-if)# dsu mode 1
Router(config-if)# dsu bandwidth 44210
Examples
The following example sets the DSU mode to cisco:
Router(config)# interface serial 1/0/0
Router(config-if)# dsu mode cisco
Related Commands
Command
Description
showcontrollers
Displays information about the controllers.
showinterfaces
Displays statistics for all interfaces configured on the
router.
dte-invert-txc
To invert the transmit external clock (TXC) signal received from the DCE when the device is operating as a DTE, use the dte-invert-txc command in interface configuration mode. If the DCE accepts serial clock transmit external (SCTE) signal when the device is operating as a DTE, use the no form of this command.
dte-invert-txc
nodte-invert-txc
Syntax Description
This command has no arguments or keywords.
Command Default
The TXC signal is not inverted.
Command Modes
Interface configuration
Command History
Release
Modification
9.1
This command was introduced.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Usage Guidelines
Use this command if the DCE cannot receive SCTE from the DTE, the data is running at high speeds, and the transmission line is long. The dte-invert-txc command prevents phase shifting of the data with respect to the clock.
On the Cisco 4000 series, you can specify the serial Network Processor Module timing signal configuration. When the board is operating as a DTE, the dte-invert-txc command inverts the TXC clock signal it gets from the DCE that the DTE uses to transmit data.
If the DCE accepts SCTE from the DTE, use nodte-invert-txc.
Examples
The following example inverts the TXC on serial interface 0:
Router(config)# interface serial 0
Router(config-if)# dte-invert-txc
duplex
To configure the duplex operation on an interface, use the duplex command in interface configuration mode. To return to the default configuration, use the
no form of this command.
duplex
{ full | half | auto }
noduplex
Syntax Description
full
Specifies full-duplex operation.
half
Specifies half-duplex operation.
auto
Enables autonegotiation. The interface automatically operates at half-duplex or full-duplex mode depending on environmental factors, such as the type of media and the transmission speeds for the peer routers, hubs, and switches used in the network configuration.
Command Default
Half-duplex mode is enabled.
For the 4-port 10/100 Fast Ethernet Shared Port Adapter (SPA) and the 2-port 10/100/1000 Gigabit Ethernet SPA on the Cisco 7304 router, autonegotiation is enabled. The command is set to auto.
Command Modes
Interface configuration (config-if)
Command History
Release
Modification
11.2(10)P
This command was introduced.
12.2S
This command was integrated into Cisco IOS Release 12.2S.
12.2(14)SX
This command was implemented on the Supervisor Engine 720.
12.2(17d)SXB
This command was integrated into Cisco IOS Release 12.2 SXB.
12.2(20)S2
This command was implemented on the 4-port 10/100 Fast Ethernet SPA and the 2-port 10/100/1000 Gigabit Ethernet SPA on the Cisco 7304 router.
Cisco IOS XE Release 3.9S
This command was integrated into Cisco IOS XE Release 3.9S.
15.2(02)SA
This command was implemented on the Cisco ME 2600X Series Ethernet Access Switches.
Usage Guidelines
To use the autonegotiation capability (that is, to automatically detect speed and duplex modes), you must set both the
speed command and the
duplex command to auto.
Cisco Cloud Services Router 1000V Series
Cisco Cloud Services Router 1000V Series does not support the duplex command.
Duplex Options and Interfaces
The table below lists the supported command options by interface type.
Table 1 Supported Duplex Command Options
Interface Type
Supported Syntax
Default Setting
Usage Guidelines
10/100-Mbps module
duplex [half | full]
See the “Usage Guidelines” column.
Run the
no duplex autocommand to set the speed to
auto.
If the speed is set to
10 or
100, without configuring the duplex setting, the duplex is set to
half.
100-Mbps fiber modules
duplex [half | full]
half
Gigabit Ethernet interfaces
duplexfull
full
10-Mbps ports
duplex [half | full]
half
If the transmission speed on a 16-port RJ-45 Gigabit Ethernet port is set to 1000, the duplex mode is set to full. If the transmission speed is changed to 10 or 100, the duplex mode stays at half duplex. You must configure the correct duplex mode when the transmission speed is changed to 10 or 100 from 1000.
Gigabit Ethernet is full duplex only. You cannot change the mode on Gigabit Ethernet ports.
When manually configuring the interface speed to either 10 or 100-Mbps, you should also configure the duplex mode on the interface.
Caution
Changing the interface speed and duplex mode configuration might shut down and reenable the interface during reconfiguration.
4-Port 10/100 Fast Ethernet SPA and 2-Port 10/100/1000 Gigabit Ethernet SPA on the Cisco 7304 Router
The
duplex command is applied to the SPA interfaces that use the RJ-45 media. Gigabit Ethernet interfaces using fiber media support full-duplex mode only and use the
negotiation command to enable and disable autonegotiation.
To enable the autonegotiation capability on an RJ-45 interface, you must set either the
speed command or the
duplex command to
auto. The default configuration is that both commands are set to
auto.
Note
For the Cisco AS5300, the
duplex{full| half| auto} command syntax replaces the duplex commands—half-duplex and
full-duplex. Cisco 7600 series routers can automatically negotiate the interface speed and the duplex mode only if one of the connected interfaces are configured to
auto.
The table below describes the interface behavior for different combinations of the
duplex and
speed command settings. The specified
duplex command configured with the specified
speed command produces the resulting system action.
If you specify both
duplex and
speed settings other than
auto on an RJ-45 interface, autonegotiation is disabled for the interface.
Note
If you need to force an interface port to operate with certain settings and, therefore, need to disable autonegotiation, you must be sure that the remote link is configured with compatible link settings for proper transmission including the support of flow control on the link.
Note
Every interface on a 4-port 10/100 Fast Ethernet SPA supports transmission of pause frames to stop packet flow when the Modular Services Card (MSC) is full. You cannot disable flow control for an interface on the 4-port 10/100 Fast Ethernet SPA. Hence, the flow control support is not configurable, but it is advertised during autonegotiation. If you disable autonegotiation, you must be sure that the remote device is configured to support flow control because flow control is automatically enabled for all interfaces on the 4-port 10/100 Fast Ethernet SPA.
Table 2 Relationship Between duplex and speed Commands
duplex Command
speed Command
Resulting System Action
duplexauto
speedauto
Autonegotiates both speed and duplex modes. The interface advertises the capability for the following link settings:
10 Mbps and half duplex
10 Mbps and full duplex
100 Mbps and half duplex
100 Mbps and full duplex
1000 Mbps and half duplex
1000 Mbps and full duplex
duplexauto
speed10 or speed100 or speed1000
Autonegotiates the duplex mode. The interface advertises the capability for the configured speed with the capability for both half-duplex or full-duplex mode.
For example, if the
speed100 command is configured with
duplexauto, then the interface advertises the following capability:
100 Mbps and half duplex
100 Mbps and full duplex
duplexhalf or duplexfull
speedauto
Autonegotiates the speed. The interface advertises the capability for duplex mode for Fast Ethernet interfaces at a speed of 10-Mbps and 100-Mbps, and Gigabit interfaces at 10-Mbps, 100-Mbps, and 1000-Mbps.
For example, if the
duplexfull command is configured with the
speedauto command, then the interface advertises the following capability:
10 Mbps and full duplex
100 Mbps and full duplex
1000 Mbps and full duplex (Gigabit Ethernet interfaces only)
duplexhalf
speed10
Forces 10-Mbps speed and the half-duplex operation, and disables autonegotiation on the interface.
duplexfull
speed10
Forces a speed of 10-Mbps and the full-duplex operation, and disables autonegotiation on the interface.
duplexhalf
speed100
Forces a speed of 100-Mbps and the half-duplex operation, and disables autonegotiation on the interface.
duplexfull
speed100
Forces a speed of 100-Mbps and the full-duplex operation, and disables autonegotiation on the interface.
duplexhalf
speed1000
Forces a speed of 1000-Mbps and the half-duplex operation, and disables autonegotiation on the interface (Gigabit Ethernet only).
duplexfull
speed1000
Forces a speed of 1000-Mbps and the full-duplex operation, and disables autonegotiation on the interface (Gigabit Ethernet only).
Examples
The following example shows how to configure a full-duplex operation on a Cisco AS5300 router:
Device(config)# interface fastethernet 0
Device(config-if)# duplex full
The following example shows how to specify the advertisement of only half-duplex support and either 10-Mbps or 100-Mbps capability during autonegotiation for the second interface (port 1) on the SPA located in the bottom subslot (1) of the MSC that is installed in slot 2 of the Cisco 7304 router:
With this configuration, the interface advertises the following capabilities during autonegotiation:
10 Mbps and half duplex
100 Mbps and half duplex
Note
Flow control support is always advertised when autonegotiation is enabled.
Related Commands
Command
Description
interface
Configures an interface and enters interface configuration mode.
interfacefastethernet
Selects a particular Fast Ethernet interface for configuration.
interfacegigabitethernet
Selects a particular Gigabit Ethernet interface for configuration.
showcontrollers
Displays information that is specific to the hardware on a module.
showcontrollersfastethernet
Displays Fast Ethernet interface information, transmission statistics, and errors, and the applicable MAC destination address and VLAN filtering tables.
showcontrollersgigabitethernet
Displays Gigabit Ethernet interface information, transmission statistics, and errors, and the applicable MAC destination address and VLAN filtering tables.
showinterfaces
Displays traffic that is seen by a specific interface.
showinterfacesfastethernet
Displays information about Fast Ethernet interfaces.
showinterfacesgigabitethernet
Displays information about Gigabit Ethernet interfaces.
speed
Sets the port speed for a Fast Ethernet interface.
dxi interface-dfa
To specify a map command for a point to point serial interface, use the Data Exchange Interface (dxi) command dxiinterface-dfa in interface configuration mode. To deletct the map command, use the no form of this command.
dxiinterface-dfavpi-numbervci
[ snap | mux ]
nodxiinterface-dfavpi-numbervci
Syntax Description
vpi-number
ATM network virtual path identifier (VPI) of the permanent virtual circuit (PVC), in the range from 0 to 15. The VPI is a 4-bit field in the header of the ATM DXI frame. The VPI value is unique only on a single interface, not throughout the ATM network, because it has local significance only.
Both vpi and vci cannot be specified as 0; if one is 0, the other cannot be 0.
vci
ATM network virtual channel identifier (VCI) of this PVC, in the range from 0 to 63. The VCI is a 6-bit field in the header of the ATM DXI frame. The VCI value is unique only on a single interface, not throughout the ATM network, because it has local significance only.
Both vpi
and vci
cannot be specified as 0; if one is 0, the other cannot be 0.
snap
(Optional) LLC/SNAP encapsulation based on the protocol used in the packet. This keyword defines a PVC that can carry multiple network protocols. This is the default.
mux
(Optional) Enables multiplex (mux) encapsulation.
Command Default
No map command is specified.
Command Modes
Interface configuration
Command Default
No map definition is established.
Command Modes
Interface configuration
Command History
Release
Modification
10.3
This command was introduced.
12.4
This command was integrated into Cisco IOS Release 12.4.
Examples
The following example shows how to specify a map command.
Router(config)# interface serial 1
Router(config-if)# dxi interface-dfa 10
Related Commands
Command
Description
encapsulationatm-dxi
Enables ATM-DXI encapsulation.
dxipvc
Configures multiprotocol or single protocol AMT-Data Exchange Interface (dxi) encapsulation.
dximap
Maps a protocol address to a given virtual path identifier (VPI) and virtual channel identifier (VCI).
showdxipvc
Displays the PVC statistics for a serial interface.
smds dxi
Enables Data Exchange Interface (dxi) version 2.2 support.
dxipvc
Configures multiprotocol or single protocol AMT-Data Exchange Interface (dxi) encapsulation.
dxs3mode
To define the controller type as an E3 or T3 controller, use the dxs3mode command in controller configuration mode. To remove the controller, use the no form of this command.
Adds a description to identify particulars about a controller.
e2-clockrate
To configure serial interface 0 for E2 (8 MHz full duplex) and to shut down the other three serial interfaces (1 to 3), use the e2-clockrate command in interface configuration mode. To disable the full duplex E2, use the no form of this command.
e2-clockrate
noe2-clockrate
Syntax Description
This command has no arguments or keywords.
Command Default
All interfaces are running.
Command Modes
Interface configuration
Command History
Release
Modification
12.0(2)XD
This command was introduced.
12.0(3)T
This command was integrated into Cisco IOS Release 12.0(3)T.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Usage Guidelines
The e2-clockrate command is an interface configuration command and is seen only with interfaceserial0. When this command is used, serial interface 0 supports speeds up to E2 (8 MHz full duplex) and the other three serial interfaces (1 to 3) are put in the “shutdown” state. Also, running this command displays the following warning message:
Serial interface 0 is configured to support E2 rates and serial ports “1-3” are moved to shutdown state
.
Examples
The following example shows sample display output for the e2-clockrate EXEC command.
Router(config-if)#
e2-clockrate
Interface Serial 0 is configured to support clockrates up to E2 (8Mbps)
Interfaces serial 1-3 will not be operational
Related Commands
Command
Description
clockrate
Configures the clock rate for the hardware connections on serial interfaces such as NIMs and interface processors to an acceptable bit rate.
early-token-release
To enable early token release on Token Ring interfaces, use the early-token-release command in interface configuration mode. To disable this function, use the no form of this command.
early-token-release
noearly-token-release
Syntax Description
This command has no arguments or keywords.
Command Default
Disabled
Command Modes
Interface configuration
Command History
Release
Modification
10.0
This command was introduced.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Usage Guidelines
Early token release is a method whereby the Token Ring interfaces can release the token back onto the ring immediately after transmitting, rather than waiting for the frame to return. This feature helps increase the total bandwidth of the Token Ring.
The Token Ring Interface Processor (TRIP) on the Cisco 7500 series routers and the Token Ring adapters on the Cisco 7200 series routers all support early token release.
Examples
The following example enables the use of early token release on Token Ring interface 1:
The following example enables the use of early token release on the Token Ring interface processor in slot 4 on port 1 on the Cisco 7500 series routers:
The efm-grp command is used to perform the necessary link operations (add, delete, and shutdown) of a single link after the creation of efm-bonding group. To perform the link operations in the efm-grp command, enter the config-controller-dsl-group mode. Use the no form of the command to shut down the related command.
This command is used to add, delete, or shutdown a link in the efm-bond.
Examples
The following example shows how efm-grp command is used.
Router(config-controller-dsl-group)# efm-grp ?
add Add a link to the EFM Bonding group
delete Delete a link from the EFM Bonding group
shutdown Shutdown a link in the EFM Bonding group
Router(config-controller-dsl-group)# efm-grp add ?
link EFM Bonding group link configuration
Router(config-controller-dsl-group)# efm-grp add link ?
<0-3> Link pair number
Related Commands
Command
Description
controllershdsl
Configures a controller for SHDSL mode and enters config-controller mode.
shdslannex
Defines the SHDSL G.991.2 standard.
shdslrate
Defines the SHDSL rate.
showcontrollershdsl
Displays the status of the controller that is configured for SHDSL mode.
eigrp interface
Note
Effective with Cisco IOS Release 15.0(1)M, the eigrpinterfacecommand is replaced by the dampening-change command and the dampening-interval command. See the dampening-change and dampening-intervalcommands for more information.
To set a threshold value to minimize hysteresis in a router-to-radio configuration, use the eigrpinterface command in interface configuration mode. To reset the hysteresis threshold to the default value, use the no form of this command.
(Optional) Value used to minimize the effect of frequent routing changes in router-to-radio configurations. Percent interface metric must change to cause update. Value range is 1 to 100.
dampening-intervalvalue
(Optional) Specifies the time interval in seconds to check the interface metrics at which advertising of routing changes occurs. The default value is 30 seconds. Value range is 1 to 65535.
Command Default
Default for change-based dampening is 50 percent of the computed metric.
Default for interval-based dampening is 30 seconds.
Command Modes
Interface configuration (config-if)
Command History
Release
Modification
12.4(15)XF
This command was introduced.
12.4(15)T
This command was integrated into Cisco IOS Release 12.4(15)T.
15.0(1)M
This command was replaced. This command was replaced by the dampening-changecommand and the dampening-interval command.
Usage Guidelines
This command advertises routing changes for EIGRP traffic only.
The REPLY sent to any QUERY will always contain the latest metric information. Exceptions which will result in immediate UPDATE being sent:
A down interface
A down route
Any change in metric which results in the router selecting a new next hop
Change-based Dampening
The default value for the change tolerance will be 50% of the computed metric. It can be configured in the range from 0 to 100 percent. If the metric change of the interface is not greater (or less) than the current metric plus or minus the specified amount, the change will not result in a routing change, and no update will be sent to other adjacencies.
Interval-based Dampening
The default value for the update intervals is 30 seconds. It can be configured in the range from 0 to 64535 seconds. If this option is specified, changes in routes learned though this interface, or in the interface metrics, will not be advertised to adjacencies until the specified interval is met. When the timer expires, any changes detected in any routes learned through the interface, or the metric reported by the interfaces will be sent out.
Examples
Examples
The following example sets the threshold to 50 percent tolerance routing updates involving VMI interfaces and peers:
When the CEM is in rx-only mode, there is no data transmitted by that CEM. The CEM status shows “active (rx-only)”.
tx
The CEM in tx-only mode does not receive any data. There is no data sent to the IP side and the received data is silently dropped at the CEM. The CEM status shows “active (tx-only)”.
Command Default
Default mode is unidirectional mode.
Command Modes
Configuration CEM mode (emulation-mode).
Command History
Release
Modification
12.4(20)YA
This command was introduced.
Usage Guidelines
You can use the emulation-mode command to configure the CEM in unidirectional mode. Once configured, traffic will flow only in that direction through the CEM channel. The CEM status will show as “active (rx-only)” or “active (tx-only)” depending on the configuration. To disable the command's effect, use the
no form of this command.
Examples
The following example shows how the command configures the traffic in unidirectional mode:
The following example shows how the command configures the traffic in bidirectional mode:
Router(config-cem
)# emulation-mode bidirectional
encapsulation
To set the encapsulation method used by the interface, use the encapsulation command in interface configuration mode. To remove the encapsulation, use the no form of this command.
encapsulationencapsulation-type
noencapsulationencapsulation-type
Syntax Description
encapsulation-type
Encapsulation type; one of the following keywords:
atm-dxi--
ATM Mode-Data Exchange Interface.
bstun--Block Serial Tunnel.
dot1qvlan-id [native]--Enables IEEE 802.1q encapsulation of traffic on a specified subinterface in VLANs. The vlan-id argument is a virtual LAN identifier. The valid range is from 1 to 1000. The optional native keyword sets the PVID value of the port to the vlan-id value.
frame-relay--Frame Relay (for serial interface).
hdlc--
High-Level Data Link Control (HDLC) protocol for serial interface. This encapsulation method provides the synchronous framing and error detection functions of HDLC without windowing or retransmission. This is the default for synchronous serial interfaces.
islvlan-id--Inter-Switch Link (ISL) (for VLANs).
lapb--X.25 Link Access Procedure, Balanced. Data link layer protocol (LAPB) DTE operation (for serial interface).
ppp--
PPP
(for serial interface).
sdesaid--IEEE 802.10. The said argument is a security association identifier. This value is used as the VLAN identifier. The valid range is from 0 to 0xFFFFFFFE.
sdlc--IBM serial Systems Network Architecture (SNA).
sdlc-primary--IBM serial SNA (for primary serial interface)
.
sdlc-secondary--IBM serial SNA (for secondary serial interface).
slip--Specifies Serial Line Internet Protocol (SLIP) encapsulation for an interface configured for dedicated asynchronous mode or dial-on-demand routing (DDR). This is the default for asynchronous interfaces.
smds--Switched Multimegabit Data Services (SMDS) (for serial interface).
ss7--Sets the encapsulation type to SS7 and overrides the serial interface objects high-level data link control (HDLC) default.
Command Default
The default depends on the type of interface. For example, synchronous serial interfaces default to HDLC and asynchronous interfaces default to SLIP.
Command Modes
Interface configuration
Command History
Release
Modification
10.0
This command was introduced.
10.3
The sde keyword was added to support IEEE 802.10
11.1
The isl keyword was added to support the Interswitch Link (ISL) Cisco protocol for interconnecting multiple switches and routers, and for defining virtual LAN (VLAN) topologies.
11.3(4)T
The tr-isltrbrf-vlan keyword was added to support TRISL, a Cisco proprietary protocol for interconnecting multiple routers and switches and maintaining VLAN information as traffic goes between switches.
12.0(1)T
The dot1q keyword was added to support IEEE 8021q standard for encapsulation of traffic on a specified subinterface in VLANs.
12.1(3)T
The native keyword was added.
12.2(11)T
This command was modified to include the ss7 keyword in support of integrated signaling link terminal capabilities.
12.2(13)T
Support for IPv6 was added.
12.3(2)T
The tr-isltrbrf-vlan keyword was removed because support for the TRISL protocol is no longer available in Cisco IOS software.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
Cisco IOS XE Release 2.5
This command was updated. It was integrated into Cisco IOS XE Release 2.5.
Usage Guidelines
SLIP and PPP
To use SLIP or PPP, the router or access server must be configured with an IP routing protocol or with the iphost-routing command. This configuration is done automatically if you are using old-style slipaddress commands. However, you must configure it manually if you configure SLIP or PPP via the interfaceasync command.
On lines configured for interactive use, encapsulation is selected by the user when they establish a connection with the slip or ppp EXEC command.
IP Control Protocol (IPCP) is the part of PPP that brings up and configures IP links. After devices at both ends of a connection communicate and bring up PPP, they bring up the control protocol for each network protocol that they intend to run over the PPP link such as IP or IPX. If you have problems passing IP packets and the showinterface command shows that line is up, usethenegotiations command to see if and where the negotiations are failing. You might have different versions of software running, or different versions of PPP, in which case you might need to upgrade your software or turn off PPP option negotiations. All IPCP options as listed in
RFC 1332, PPP Internet Protocol Control Protocol (IPCP)
, are supported on asynchronous lines. Only Option 2, TCP/IP header compression, is supported on synchronous interfaces.
PPP echo requests are used as keepalive packets to detect line failure. The nokeepalive command can be used to disable echo requests. For more information about the nokeepalive command, refer to the chapter “IP Services Commands” in the CiscoIOSIPCommandReference,Volume1of4:AddressingandServicesand to thechapter“Configuring IP Services” in the CiscoIOSIPConfigurationGuide.
To use SLIP or PPP, the Cisco IOS software must be configured with an IP routing protocol or with the iphost-routing command. This configuration is done automatically if you are using old-style slipaddress commands. However, you must configure it manually if you configure SLIP or PPP via the interfaceasync command.
Note
Disable software flow control on SLIP and PPP lines before using the encapsulation command.
SS7
The SS7 encapsulation command is new with the Integrated SLT feature and is available only for interface serial objects created by the channel-group command. For network access server (NAS) platforms, the encapsulation for channel group serial interface objects defaults to HDLC. You must explicitly set the encapsulation type to SS7 to override this default.
When encapsulation is set to SS7, the encapsulation command for that object is no longer available. A serial SS7 link is deleted only when its associated dial feature card (DFC) card is removed. As with existing Cisco 26xx-based SLTs, you do not need to specify whether the SS7 link is to be used as an A-link or an F-link.
By itself this command does not select the correct encapsulation type. Therefore, once created, you must set the encapsulation type to the new SS7 value, as well as assign a session channel ID to the link at the serial interface command level. The configuration on a digital SS7 link can be saved (no shutdown) only when its encapsulation is successfully set to SS7 and it has been assigned a channel identifier.
VLANs
Do not configure encapsulation on the native VLAN of an IEEE 802.1q trunk without the native keyword. (Always use the native keyword when the vlan-id is the ID of the IEEE 802.1q native VLAN.)
For detailed information on use of this command with VLANs, refer to the Cisco IOS Switching Services Configuration Guide
and the Cisco IOS Switching Services Command Reference
.
Examples
The following example shows how to reset HDLC serial encapsulation on serial interface 1:
Router(config)# interface serial 1
Router(config-if)# encapsulation hdlc
The following example shows how to enable PPP encapsulation on serial interface 0:
Router(config)# interface serial 0
Router(config-if)# encapsulation ppp
The following example shows how to configure async interface 1 for PPP encapsulation:
To learn more about the virtual serial interface and check SS7 encapsulation, enter the show interfaces serial slot/trunk:channel-group command in privileged EXEC mode, as in the following example:
Router# show interfaces serial 7/3:1
Serial7/3:1 is up, line protocol is down
Hardware is PowerQUICC Serial
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 4/255, rxload 1/255
Encapsulation SS7 MTP2, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters 03:53:40
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 26000 bits/sec, 836 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11580159 packets output, 46320636 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
2 carrier transitions
DCD=up DSR=down DTR=down RTS=down CTS=down
Related Commands
Command
Description
channel-group
Assigns a channel group and selects the DSO time slots desired for SS7 links.
encapsulationx25
Specifies operation of a serial interface as an X.25 device.
keepalive
Sets the keepalive timer for a specific interface.
ppp
Starts an asynchronous connection using PPP.
pppauthentication
Enables CHAP or PAP or both and specifies the order in which CHAP and PAP authentication are selected on the interface.
pppbapcall
Sets PPP BACP call parameters.
slip
Starts a serial connection to a remote host using SLIP.
end (satellite initial configuration)
To exit satellite initial configuration mode, save any new or changed parameters, and reset the Cisco IP VSAT satellite WAN network module (NM-1VSAT-GILAT), use the end command in satellite initial configuration mode.
end
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values
Command Modes
Satellite initial configuration
Command History
Release
Modification
12.3(14)T
This command was introduced.
Usage Guidelines
The end command is identical to the exit command in satellite initial configuration mode.
When you enter the exit or end command to exit satellite initial configuration mode, the system automatically saves any changed parameters to the NM-1VSAT-GILAT network module nonvolatile memory and resets the NM-1VSAT-GILAT network module.
Examples
The following example shows what appears when you enter the end or exitcommand after changing one or more initial configuration parameters:
Router(sat-init-config)# end
Applying changed parameters to the satellite module.
Parameter update succeeded. Module is now resetting.
Router#
The following example shows what appears when you enter the end or exit command when no parameters have been changed:
Router(sat-init-config)# end
Router#
Related Commands
Command
Description
apply
Saves new or changed satellite initial configuration parameters and resets the Cisco IP VSAT satellite WAN network module (NM-1VSAT-GILAT).
exit(satelliteinitialconfiguration)
Exits satellite initial configuration mode, saves any new or changed parameters, and resets the Cisco IP VSAT satellite WAN network module (NM-1VSAT-GILAT).
equipment loopback
To run loopbacks in conjunction with remote equipment, use the equipmentloopbackcommand in controller configuration mode. To terminate the loopback, use the no form of this command.
equipment
[ customer | network ]
loopback
noequipment
[ customer | network ]
loopback
Syntax Description
customer
(Optional) Enables the line card to respond to remote T3 loopback commands from the remote T3 equipment.
network
(Optional) Causes the line card to ignore remote T3 loopback commands.
Command Default
No default behavior or values.
Command Modes
Controller configuration
Command History
Release
Modification
12.2S
This command was introduced
Examples
The following example configures an equipment network loopback:
To enable error-disable detection, use the
errdisabledetectcausecommand in global configuration mode. To disable error-disable detection, use the
no form of this command.
Specifies error-disable detection for all error-disable causes.
bpduguard
Specifies detection for the Bridge Protocol Data Unit (BPDU)-guard error-disable cause.
dtp-flap
Specifies detection for the Dynamic Trunking Protocol (DTP)-flap error-disable cause.
l2ptguard
Specifies detection for the Layer 2 Protocol Tunneling guard error-disable cause.
link-flap
Specifies detection for the link flap error-disable cause.
packet-buffer-error
Causes the packet buffer error to error-disable the affected port.
pagp-flap
Specifies detection for the Port Aggregation Protocol (PAgP)-flap error-disable cause.
rootguard
Specifies detection for the root-guard error-disable cause.
udld
Specifies detection for the Unidirectional Link Detection (UDLD) error-disable cause.
Command Default
Error-disable detection is enabled for all causes.
Command Modes
Global configuration (config)
Command History
Release
Modification
15.0(1)M
This command was introduced in a release earlier than Cisco IOS Release 15.0(1)M.
12.2(14)SX
This command was modified. Support was added for the Supervisor Engine 720.
12.2(17b)SXA
This command was modified. The
packet-buffer-error keyword was added.
12.2(17d)SXB
This command was modified. Support for this command on the Supervisor Engine 2 was extended to Release 12.2(17d)SXB.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
Usage Guidelines
Note
Entering the
noerrdisabledetectcausepacket-buffer-error command allows you to detect the fault that triggers a power cycle of the affected module.
A cause (bpduguard, dtp-flap, link-flap, pagp-flap, root-guard, udld) is defined as the reason why the error-disable state occurred. When a cause is detected on an interface, the interface is placed in an error-disable state (an operational state that is similiar to the link-down state).
You must enter the
shutdown and then the
noshutdown commands to recover an interface manually from the error-disable state.
Examples
The following example shows how to enable error-disable detection for the Layer 2 protocol-tunnel guard error-disable cause:
Router(config)#
errdisable detect cause l2ptguard
Related Commands
Command
Description
showerrdisabledetect
Displays the error-disable detection status.
showinterfacesstatus
Displays the interface status or a list of interfaces in an error-disable state on LAN ports only.
shutdown
Disables an interface.
errdisable recovery
To configure recovery mechanism variables, use the
errdisablerecovery command in global configuration mode. To return to the default state, use the
no form of this command.
Enables error-disable recovery from a specific cause.
all
Enables the recovery timers for all error-disable causes.
arp-inspection
Enables error-disable recovery from an Address Resolution Protocol (ARP) inspection cause.
bpduguard
Enables the recovery timer for the Bridge Protocol Data Unit (BPDU)-guard error-disable cause.
channel-misconfig
Enables the recovery timer for the channel-misconfig error-disable cause.
dhcp-rate-limit
Enables the recovery timer for the Dynamic Host Configuration Protocol (DHCP)-rate-limit error-disable cause.
dtp-flap
Enables the recovery timer for the Dynamic Trunking Protocol (DTP)-flap error-disable cause.
gbic-invalid
Enables the recovery timer for the Gigabit Interface Converter (GBIC)-invalid error-disable cause.
l2ptguard
Enables the recovery timer for the Layer 2 Protocol Tunneling (L2PT) error-disable cause.
link-flap
Enables the recovery timer for the link-flap error-disable cause.
pagp-flap
Enables the recovery timer for the Port Aggregation Protocol (PAgP)-flap error-disable cause.
psecure-violation
Enables the recovery timer for the psecure-violation error-disable cause.
security-violation
Enables the automatic recovery of ports that were disabled because of 802.1X security violations.
rootguard
Enables the recovery timer for the root-guard error-disable cause.
udld
Enables the recovery timer for the Unidirectional Link Detection (UDLD) error-disable cause.
unicast-flood
Enables the recovery timer for the unicast-flood error-disable cause.
intervalseconds
Specifies the time, in seconds, to recover from a specified error-disable cause. The range is from 30 to 86400. The default interval is 300.
Command Default
The recovery mechanisms are disabled.
Command Modes
Global configuration (config)
Command History
Release
Modification
15.0(1)M
This command was introduced in a release earlier than Cisco IOS Release 15.0(1)M.
12.2(14)SX
This command was modified. This command was implemented on the Supervisor Engine 720.
12.2(17d)SXB
This command was modified. This command was implemented on the Supervisor Engine 2.
12.2(18)SXD
This command was modified. The
arp-inspection keyword was added.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
Usage Guidelines
A cause (bpduguard, channel-misconfig, dhcp-rate-limit, dtp-flap, l2ptguard, link-flap, pagp-flap, psecure-violation, security-violation, rootguard, udld, or unicast-flood) is defined as the reason why the error-disable state occurred. When a cause is detected on an interface, the interface is placed in an error-disable state (an operational state that is similar to the link-down state). If you do not enable error-disable recovery for the cause, the interface stays in the error-disable state until a shutdown and no shutdown occur. If you enable recovery for a cause, the interface is brought out of the error-disable state and allowed to retry operation once all the causes have timed out.
You must enter the
shutdown command and then the
noshutdown command to manually recover an interface from the error-disable state.
Note
A separate line is required each time you want to enter the
errdisablerecoverycause command to add a new reason for recovery; each new reason does not get appended to the original single line. This means you must enter each new reason separately.
Examples
This example shows how to enable the recovery timer for the BPDU-guard error-disable cause:
Router(config)#
errdisable recovery cause bpduguard
This example shows how to set the recovery timer to 300 seconds:
Router(config)#
errdisable recovery interval 300
Related Commands
Command
Description
showerrdisablerecovery
Displays the information about the error-disable recovery timer.
showinterfacesstatus
Displays the interface status or a list of interfaces in an error-disabled state on LAN ports only.
shutdown
Disables an interface.
error throttling
To stop receiving error data packets on multiple channel groups configured on all interfaces on the T1 controller of a channelized T3 port adapter or on the E1 controller of a channelized E3 port adapter, use the errorthrottling command in controller configuration mode. To continue receiving error data packets on all channels on the T1 or E1 controller, use the no form of this command.
errorthrottling
noerrorthrottling
Syntax Description
This command has no arguments or keywords.
Command Default
The errorthrottling command is enabled by default on a T3 or a E3 port adapter.
Command Modes
Controller configuration (config-controller)
Command History
Release
Modification
12.2(19c)
This command was introduced.
15.0(1)M3
This command was modified. This command can be enabled on E1 controllers.
12.2(33)SRD5
This command was integrated into Cisco IOS Release 12.2(33)SRD5.
Usage Guidelines
Use the showcontrollerst3 command or showcontrollerse3 command to display whether the current router configuration has error throttling enabled or disabled.
The errorthrottling command disables the T1 or E1 level clock in order to stop receiving error data packets on a T1 or E1 controller.
When a T1 or a E1 has multiple channel groups configured over it, error throttling affects all the channels on a T1 or a E1. If any single interface receives a burst of errors, over a short duration, such as 400 errors in 100 milliseconds (ms), the T1 or E1 clock is turned off for a period of 100 ms. When there is a high rate of errors, the error rate is likely to continue for a long duration of time. Using error throttling to stop receiving the error data packets reduces wasteful processing and discarding of error packets.
The noerrorthrottling command allows all the error data packets to be processed, dropped, and accounted for on a T1 or a E1 controller. When the error rate is high, the CPU can become overloaded.
When the noerrorthrottling command is used to configure a T3 or a E3 port, the configuration applies to all of the 28 associated T1 or E1 channels.
Examples
The following example enables error throttling by disabling the T1 clock in order to stop receiving error data packets on a T1 controller:
Router(config-controller)# error throttling
The following example uses the showcontrollerst3 command to display partial output showing that error throttling is enabled on the T1 controller:
Router# show controllers t3 2/1/0
T3 2/1/0 is down. Hardware is 2CT3 single wide port adapter
CT3 H/W Version: 0.2.2, CT3 ROM Version: 1.0, CT3 F/W Version: 2.5.1
FREEDM version: 1, reset 0 resurrect 0
Applique type is Channelized T3
Transmitter is sending remote alarm.
Receiver has loss of signal.
FEAC code received: No code is being received
Framing is M23, Line Code is B3ZS, Clock Source is Internal
Rx-error throttling on T1's ENABLED
.
The following example uses the showcontrollerse3 command to display partial output showing that error throttling is enabled on the E1 controller:
Router# show controller e3 5/0
*Mar 14 21:19:06.795: %SYS-5-CONFIG_I: Configured from console by console
E3 5/0 is up.
CE3 H/W Version : 3.1.0, CE3 ROM Version : 1.1, CE3 F/W Version : 1.2.1
Applique type is Channelized E3
Total available channels 128, used 4
No alarms detected. Line Code is HDB3, Clock Source is Line.
Rx-error throttling on E1's ENABLED
Data in current interval (564 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation
0 P-bit Err Secs, 0 P-bit Severely Err Secs
0 Severely Err Framing Secs, 0 Unavailable Secs
0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
E3 5/0 E1 1
No alarms detected.
Framing is crc4, Clock Source is line, National bits are 0x1F.
Data in current interval (565 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavail Secs
E3 5/0 E1 2
No alarms detected.
Framing is crc4, Clock Source is line, National bits are 0x1F.
Related Commands
Command
Description
show controllers e3
Displays information about E3 links, and displays hardware and software driver information for the E3 controller.
show controllers t3
Displays information about T3 links, and displays hardware and software driver information for the T3 controller.
esmc mode ql-disabled
To disable the Ethernet synchronization message channel (ESMC) on an interface, use the
esmcmodeql-disabledcommand in interface configuration mode. To remove the quality level (QL) disabled mode and get back to the default ql-enabled mode, use the
no form of this command.
esmcmodeql-disabled
noesmcmodeql-disabled
Syntax Description
This command has no arguments or keywords.
Command Default
The ESMC mode is ql-enabled.
Command Modes
Interface configuration (config-if)
Command History
Release
Modification
15.0(1)S
This command was introduced.
15.1(2) SNI
This command was introduced in Cisco ASR 901 Aggregation Services Router.
Cisco IOS XE Release 3.8S
This command was integrated into Cisco IOS XE Release 3.8S.
Usage Guidelines
You can use the
esmc modeql-disabled command only if a synchronous Ethernet (SyncE) capable interface is installed on the device. When this command is used no QL ESMC packets are sent during network clock synchronization.
Examples
The following example shows how to enable ESMC process:
Device(config-if)# esmc mode ql-disabled
Related Commands
Command
Description
esmcprocess
Enables the ESMC process in a device.
showesmc
Displays the enabled ESMCs in a device.
showinterfacesaccounting
Displays the number of packets of each protocol type that have been sent through all configured interfaces.
esmc process
To enable the Ethernet synchronization message channel (ESMC) process in a router, use the
esmcprocesscommand in global configuration mode. To disable the process, use the
no form of this command.
esmcprocess
noesmcprocess
Syntax Description
This command has no arguments or keywords.
Command Default
The ESMC process is disabled.
Command Modes
Global configuration (config)
Command History
Release
Modification
15.0(1)S
This command was introduced.
15.1(2) SNI
This command was introduced in Cisco ASR 901 Aggregation Services Router.
Cisco IOS XE Release 3.8S
This command was integrated into Cisco IOS XE Release 3.8S.
Usage Guidelines
You can use the
esmc
process command only if a synchronous Ethernet (SyncE) capable interface is installed on the device. ESMC is the communication channel for conveying clock information in SyncE. You can use the ESMC process in a SyncE to synchronize the clock frequency over an Ethernet port.
Examples
The following example shows how to enable ESMC process:
Device(config)# esmc process
Related Commands
Command
Description
esmcmodeql-disabled
Disables the ESMC on an interface.
showesmc
Displays the enabled ESMCs in a device.
showinterfacesaccounting
Displays the number of packets of each protocol type that have been sent through all configured interfaces.
exit (satellite initial configuration)
To exit satellite initial configuration mode, save any new or changed parameters, and reset the Cisco IP VSAT satellite WAN network module (NM-1VSAT-GILAT), use the exit command in satellite initial configuration mode.
exit
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values
Command Modes
Satellite initial configuration
Command History
Release
Modification
12.3(14)T
This command was introduced.
Usage Guidelines
The exitcommand is identical to the end command in satellite initial configuration mode.
When you enter the exit or end command to exit satellite initial configuration mode, the system automatically saves any changed parameters to the NM-1VSAT-GILAT network module nonvolatile memory and resets the NM-1VSAT-GILAT network module.
Examples
The following example shows what appears when you enter the exit or endcommand after changing one or more initial configuration parameters:
Router(sat-init-config)# exit
Applying changed parameters to the satellite module.
Parameter update succeeded. Module is now resetting.
Router#
The following example shows what appears when you enter the exit or endcommand when no parameters have been changed:
Router(sat-init-config)# exit
Router#
Related Commands
Command
Description
apply
Saves new or changed satellite initial configuration parameters and resets the Cisco IP VSAT satellite WAN network module (NM-1VSAT-GILAT).
end(satelliteinitialconfiguration)
Exits satellite initial configuration mode, saves any new or changed parameters, and resets the Cisco IP VSAT satellite WAN network module (NM-1VSAT-GILAT).