Table Of Contents
Preface
Objectives
Audience
Document Organization
New and Modified Commands by Release
New and Modified Commands in Cisco IOS-XE Release 3.3.0SQ
New and Modified Commands in Cisco IOS-XE Release 3.2.0SQ
New and Modified Commands in Cisco IOS Release 12.2(50)SQ4
New and Modified Commands in Cisco IOS Release 12.2(50)SQ2
New and Modified Commands in Cisco IOS Release 12.2(50)SQ1
New and Modified Commands in Cisco IOS Release 12.2(50)SQ
New and Modified Commands in Cisco IOS Release 12.2(44)SQ2
New and Modified Commands in Cisco IOS Release 12.2(44)SQ1
Document Conventions
Related Documentation
Obtaining Documentation and Submitting a Service Request
Preface
This guide provides information about the Cisco RF Gateway 10 (RFGW-10) command set. This preface contains the following sections:
•
Objectives
•Audience
•Document Organization
•New and Modified Commands by Release
•Document Conventions
•Related Documentation
•Obtaining Documentation and Submitting a Service Request
Objectives
This guide describes the commands necessary to configure, maintain, and troubleshoot the Cisco RF Gateway 10 Universal Edge Quadrature Amplitude Modulation (RFGW-10 UEQAM) platform.
Audience
This book is intended for system administrators and support engineers who configure and maintain the Cisco RFGW-10 and cable modem devices.
Document Organization
This command reference guide is organized as follows:
•Chapter 1—Using the Command-Line Interface in Cisco IOS Software
•Chapter 2—List of Cisco RFGW-10 Commands
•Chapter 3—Cisco RFGW-10 Commands
New and Modified Commands by Release
This section identifies new and modified commands.
New and Modified Commands in Cisco IOS-XE Release 3.3.0SQ
New commands in Cisco IOS-XE Release 3.3.0SQ:
•cable linecard encryption
•cable partition
•cable qam-group
•cable qam-partition
•cable qam-replication-group
•cable route linecard load-balance-group
•cable service-group
•cable video encryption-failover-mode
•cable video ip udp
•cable video ip multicast
•cable video pre-encrypted-multicast
•clear cable ermi statistics
•errp
•mac-address
•mgmt-ip
•pilot-qam
•qam-group
•qam-partition
•replicate-qam
•rtsp
•show cable ermi errp
•show cable ermi rtsp
•show cable qam-partition
•show_cable_qam-replication-group
•show_cable_service-group
•show_cable_video_gqi
Modified Commands in Cisco IOS-XE Release 3.3.0SQ:
•active
•cable downstream tsid
•cable mode
•cable video group
•cable video labels
•cable video multicast uplink
•cable video psi-interval
•cable video timeout
•clear_cable_video_gqi_statistics
•clear cable video packet
•clear cable video session
•keepalive retry
•protocol
•server
Integrated Commands in Cisco IOS-XE Release 3.3.0SQ:
•mac-address
•reset interval
•show cable video route
•show cable video session
•show cable video statistics packet
New and Modified Commands in Cisco IOS-XE Release 3.2.0SQ
New commands in Cisco IOS-XE Release 3.2.0SQ:
•block
•cable clock auto-revert
•cable downstream max-carriers
•cable downstream frequency (channel)
•cable downstream freq-profile
•cable downstream rf-profile
•cable downstream start-freq
•cable downstream symbol-rate
•lane
•reserve cardtype
•show cable freq-profile
•show cable linecard carrier-id-mapping
•show cable linecard licenses
•show cable linecard load-balancing-group
•show cable linecard logical-qamid-mapping
•show cable rf-profile
Modified command in Cisco IOS Release 3.2.0SQ
•cable depi dest-ip
•cable downstream annex
•cable downstream interleaver-depth
•cable downstream modulation
•cable mode
New and Modified Commands in Cisco IOS Release 12.2(50)SQ4
New commands in Cisco IOS Release 12.2(50)SQ4:
•cable midplane ping
New and Modified Commands in Cisco IOS Release 12.2(50)SQ2
New commands in Cisco IOS Release 12.2(50)SQ2:
•depi eqam-stats
•protect-tunnel
•show cable depi-sessions slot count
•show controllers linecard
•show depi session
•show depi tunnel
Modified command in Cisco IOS Release 12.2(50)SQ2:
•show cable video session
New and Modified Commands in Cisco IOS Release 12.2(50)SQ1
Modified commands in Cisco IOS Release 12.2(50)SQ1
•asm
•ssm
•cable video udp
•show cable video label
New and Modified Commands in Cisco IOS Release 12.2(50)SQ
New commands in Cisco IOS Release 12.2(50)SQ
•clear cable video packets
•clear cable video server-group
•depi-class
•dest-ip
•depi-tunnel
•ip rpc portmapper
•l2tp class
•mode
•keepalive
•reset interval
•show depi
Modified commands in Cisco IOS Release 12.2(50)SQ
•cable mode
•cable video servers
•show redundancy
Obsolete commands in Cisco IOS Release 12.2(50)SQ
•cable image-upgrade download slot
New and Modified Commands in Cisco IOS Release 12.2(44)SQ2
Modified commands in Cisco IOS Release 12.2(44)SQ2
•cable image-upgrade download
New and Modified Commands in Cisco IOS Release 12.2(44)SQ1
Modified commands in Cisco IOS Release 12.2(44)SQ1
•show cable line card version
Document Conventions
This guide uses the following conventions for command syntax descriptions and textual emphasis:
Convention
|
Description
|
boldface font
|
Commands and keywords are in boldface.
|
italic font
|
Arguments for which you supply values are in italics.
|
[ ]
|
Elements in square brackets are optional.
|
{x | y | z}
|
Alternative, mutually exclusive, keywords are grouped in braces and separated by vertical bars.
|
[x | y | z]
|
Optional alternative keywords are grouped in brackets and separated by vertical bars.
|
string
|
A nonquoted set of characters. Do not use quotation marks around the string or the string will include the quotation marks.
|
screen font
|
Terminal sessions and information the system displays are in screen font.
|
boldface screen font
|
Information you must enter is in boldface screen font.
|
italic screen font
|
Arguments for which you supply values are in italic screen font.
|
^
|
The symbol ^ represents the key labeled Control—for example, the key combination ^D in a screen display means hold down the Control key while you press the D key.
|
< >
|
Nonprinting characters, such as passwords, are in angle brackets in contexts where italics are not available.
|
[ ]
|
Default responses to system prompts are in square brackets.
|
!, #
|
An exclamation point ( ! ) or a pound sign ( # ) at the beginning of a line of code indicates a comment line.
|
Note This symbol means reader take note. Notes contain helpful suggestions or references to material not covered in the publication.
Caution This symbol means
reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
Related Documentation
This section lists the documents that provide more detailed hardware and software information about the Cisco RFGW-10 documented in this guide. These documents are available on Cisco.com.
For detailed information about the Cisco RFGW-10 platform, see the following documents:
•Cisco RF Gateway 10 Hardware Installation Guide
•Cisco RF Gateway 10 Software Feature and Configuration Guide
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
Feedback
