THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2012 Cisco Systems, Inc. All rights reserved.

A through Z Commands

emm

emm clear

show mdf

emm

To load a preconfigured Embedded Menu Manager (EMM) Menu Definition File (MDF) and launch it, use the emm command in user EXEC or privileged EXEC mode. To launch a loaded preconfigured EMM menu, use the emm command in user EXEC or privileged EXEC mode.

emm mdf mdf-url [record replay-file-url]

emm preconfigured-menu-name [record replay-file-url]

Syntax Description

mdf mdf-url

The name and location of the specified MDF to be loaded.

preconfigured-menu- name

The preconfigured menu name of the EMM menu to be launched.

record

(Optional) Invokes the recording of all actions associated with the MDF.

replay-file-url

(Optional) The name and location of the file that records all actions associated with the MDF.

Command Modes

User EXEC (#) Privileged EXEC (#)

Command History

Release

Modification

12.4(20)T

This command was introduced.

The following example shows how to load a preconfigured MDF and launch it:

Router# emm mdf disk0:bgp.mdf
================================================================================
BGP Diagnostics
Enter ? for help or ?# for item help
--------------------------------------------------------------------------------
1. Install Diagnostic Scripts
2. Set Global Variables (email parameters)
3. Deploy BGP Neighbor Loss Diagnostic Script
4. Deploy BGP Neighbor Formation Problem Diagnostic Script
5. Deploy BGP Route Problem Diagnostic Script
6. Display Diagnostic Policy Configuration
7. Remove Diagnostic Policies
8. Exit
Enter selection [8]:8
Router#
The following example shows how to launch a loaded preconfigured EMM menu:
Router# emm BGP
================================================================================
BGP Diagnostics
Enter ? for help or ?# for item help
--------------------------------------------------------------------------------
1. Install Diagnostic Scripts
2. Set Global Variables (email parameters)
3. Deploy BGP Neighbor Loss Diagnostic Script
4. Deploy BGP Neighbor Formation Problem Diagnostic Script
5. Deploy BGP Route Problem Diagnostic Script
6. Display Diagnostic Policy Configuration
7. Remove Diagnostic Policies
8. Exit
Enter selection [8]:8
Router#

Related Commands

Command

Description

debug emm

Debugs MDFs.

emm clear

Changes the terminal clear-screen escape sequence.

show mdf

Displays loaded preconfigured MDFs.

emm clear

To change the terminal clear-screen escape sequence for a terminal/terminal emulator that is not a DEC vt100 terminal/terminal emulator, use the emm clear command in privileged EXEC mode.

emm clear escape-sequence

Syntax Description

escape-sequence

The escape sequence is entered as an even number of character representations of ASCII hexadecimal data. The value 1B5B324A1B5B303B30480D should be entered.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.4(20)T

This command was introduced.

The following example shows how the terminal clear-screen escape sequence is changed for a terminal/terminal emulator that is not a DEC vt100 terminal/terminal emulator:

Router(config)# emm clear

1B5B324A1B5B303B30480D

Related Commands

Command

Description

debug emm

Debugs MDFs.

emm

Loads and launches preconfigured MDFs or launches loaded preconfigured EMM menus.

show mdf

Displays loaded preconfigured MDFs.

show mdf

To display loaded preconfigured Embedded Menu Manager (EMM) Menu Definition Files (MDFs), use the show mdf command in user EXEC or privileged EXEC mode.

show mdf

Syntax Description

This command has no arguments or keywords.

Command Modes

User EXEC (#) Privileged EXEC (#)

Command History

Release

Modification

12.4(20)T

This command was introduced.

The following is sample output from the show mdf command when a preconfigured MDF has been loaded on the router:

Router# show mdf

Menu Name / URL:
BGP / disk0:bgp.mdf

The following is sample output from the show mdf command when no MDFs exist on the router:

Router# show mdf

No menus configured!

Related Commands

Command

Description

debug emm

Debugs MDFs.

emm

Loads and launches preconfigured MDFs or launches loaded preconfigured EMM menus.

emm clear

Changes the terminal clear-screen escape sequence.